TCP Smart SMAWHTOWRAIL500W05EW Wifi Towel Radiator Instruction manual

Add to My manuals
13 Pages

advertisement

TCP Smart SMAWHTOWRAIL500W05EW Wifi Towel Radiator Instruction Manual | Manualzz
WIFI TOWEL RADIATOR
TCP Smart WiFi app-controlled towel radiator is the perfect bathroom heating solution. This advanced towel radiator comes
with Smart WiFi featuring 24/7 hour programming, with Comfort and Eco mode settings. The display panel can be fitted on
either left or right side to suit your bathroom layout.
USER INSTRUCTIONS
MODEL
SMAWHTOWRAIL500W05EW
SMABLTOWRAIL500W05EW
POWER
AC220-240V
50-60Hz 500W Class II
IMPORTANT: These instructions are for your safety. Please read thoroughly before use and retain for future
reference.
If you are in any doubt about installing this product, consult a
qualified electrician.
INSTALLATION INSTRUCTIONS
This product is suitable for indoor use only. It is IP24 rated. Do not submerge unit underwater. Do not attach to surfaces
which are damp, freshly painted or otherwise electrically conductive (eg metallic surfaces).
Please see above wall mounting instructions to ensure correct placement. Separate placement sheet is included in
the box
1) Drill holes on the wall according to the above placements.
Warning: Be sure to keep to the distances as shown in the placement instructions.
2) Fit the fasten tube in the hole and fit the bracket on the wall with screws.
3) Carefully hang the unit on the bracket, then fix the unit with the locker and screw following above picture (step 1). Then
fix the screw in step 2 by turning the lock in the bracket. Finish by covering screw heads with the cover.
Warning: Before using the heater, make sure it’s mounted tightly on the wall.
LOCATION OF INSTALLATION
This product can be installed in a bathroom but only in the area designated by the IP rating – Zone 3 – see location
information below.
Suitable for indoor only. This product is rated as IP24. If the product is to be installed within a bathroom
it can only be located within zone 3.
Zone 0
The area inside a bath or inside the shower
This area requires low voltage and an IP67
rating.
Zone 1
The area above the bath to a height of basin.
2.25m (7’ 4””) from the floor. If the light is
240V then a 30ma residual current device
(RCD) must also be used to protect the circuit
in this zone.
.
WIRING INSTRUCTIONS
The power supply to the towel
radiator must be protected in accordance with applicable standard by a 30mA differential Circuit-breaker, 16A rated. Before
carrying out any connection tasks, cut off the power supply to the electronic regulator using the circuit-breaker or the
protection fuse in the power supply circuit. This appliance does not come fitted/supplied with a fused plug. DO NOT wire/fit
a plug to this appliance.
Means for disconnection having a contact separation in all poles must be incorporated in the fixed wiring in accordance with
the wiring rules.
Connecting the power supply cable to the mains (220-240V AC)
220v – 240V +10% - 10% 50Hz monophase power supply.
Warning: you need to connect the 2 wires of the supply cable to a connection black ensuring the mains polarity is followed
as below:
IMPORTANT: The wire in the mains lead are coloured in accordance with the following code:
Blue – Neutral
Brown – Live
The blue wire must be connected to the terminal marked with an N or coloured black.
The brown wire must be connected t the terminal marked with an L or coloured red.
WARNING: Never connect live or neutral wires to the earth terminal.
All fittings must be installed by a competent person in accordance with the current IEE Wiring Regulation (BS 7671). If in
doubt, consult a qualified electrician.
SAFETY INSTRUCTIONS (to be read before operating the heater).
1.
CAUTION: Some parts of this product can become very hot and cause burns. Particular attention has to be given
where children and vulnerable people are present. Children 3 years and younger should be continually
supervised when in close proximity to the heater. Children aged from 3 to 8 years shall only switch on/off the
appliance provided that it has been placed or installed in its intended normal operating position and they
have been given supervision or instruction concerning use of the appliance in a safe way and understand the
hazards involved. Children aged from 3 to 8 years shall not plug in, regulate and clean the appliance or
perform user maintenance.
2.
Keep the power cord away from the hot body of the heater.
3.
4.
Indoor use only.
Do not use the heater in areas where flammable liquids are stored or where flammable fumes
may be present.
5.
Do not use this heater if it has been dropped;
6.
Do not use if there are visible signs of damage to the heater;
7.
Do not leave the heater switched on when your property is vacant.
WARNINGS
-
Always use the heater in an upright position.
-
If the supply cord is damaged, it must be replaced by the manufacturer, their service agent or a
similarly qualified person in order to avoid a hazard.
-
In order to avoid a hazard due to inadvertent resetting of the thermal cut out, this appliance must not
be supplied through an external switching device, such as a timer, or connected to a circuit that is
regularly switched on and off by the utility.
-
Always use this appliance with rollers fixed and ensure it is mounted tightly to the wall.
OPERATING THE RADIATOR
Manual Settings using the LCD screen
Choose a suitable location for the r a d i a t o r , taking into account the safety instructions above.
ON/OFF BUTTON
Press once to turn the device on. Press again to turn the device off.
This feature can be performed using the TCP Smart App.
MODE SELECTION
Press this button to cycle between the following options:
Press
to enter mode selection. By pressing
, the heating mode runs in a continuous cycle as above:
Comfort mode: Press
and
to set the temperature from 5-35oC.
ECO mode: This is pre-set as 4 oC below comfort mode.
Pre-programmed schedule – Select to run the programme as stated below.
- Anti-frost mode. To avoid damage to the product during extreme cold weather use anti-frost mode. The heater must
be turned on and Anti Frost mode selected for this function to work. The screen will display
7 oC. The temperature cannot be adjusted.
. The target temperature is
Pre-Programmed scheduling - Select to run the programme as stated below.
Programmable scheduling – Select to create a programme to suit your own requirements.
This feature can be performed using the TCP Smart App.
P1, P2 and P3 Programmed scheduling –
-
Note: Clock and day of the week setting must be done for the below scheduling to work.
(Monday-Sunday) Pre-programmed schedule. Please note: this schedule cannot be adjusted.
-
00:00am – 01:00am
comfort mode,
-
01:00am – 07:00am
ECO mode
-
07:00am – 00:00am
comfort mode.
(Monday-Friday)
Pre-programmed schedule. Please note: this schedule cannot be adjusted.
-
00:00am – 01:00am
comfort mode,
-
01:00am – 05:00am
ECO mode
-
05:00am – 09:00am
comfort mode,
-
09:00am – 19:00pm
ECO mode
-
19:00pm – 00:00am
comfort mode
(Saturday-Sunday) Pre-programmed schedule. Please note: this schedule cannot be adjusted.
-
00:00am – 01:00am
comfort mode,
-
01:00am – 08:00am
ECO mode
-
08:00am – 11:00am
comfort mode,
-
11:00am – 13:00pm
ECO mode
-
13:00pm – 16:00pm
comfort mode,
-
16:00pm – 20:00pm
ECO mode
-
20:00pm – 00:00am
comfort mode.
(Monday-Friday) Programmable schedule. Please note that this schedule can be adjusted to
suit your requirements using the instructions below. The below is for illustration purposes only.
00:00am – 01:00am
comfort mode,
01:00am – 05:00am
ECO mode
05:00am –09:00am
comfort mode,
09:00am – 12:00pm
ECO mode
12:00pm – 16:00pm
comfort mode,
16:00pm – 18:00pm
ECO mode
18:00pm – 00:00am
comfort mode.
(Saturday-Sunday) Programmable schedule. Please note that this schedule can be adjusted to suit your
requirements using the instructions below. The below is for illustration purposes only.
00:00am – 01:00am
comfort mode,
01:00am – 05:00am
ECO mode
05:00am –00:00am
comfort mode
Adjustable program setting
1.
Press
2.
The screen will display
1
2
3
4
Monday
Tuesday
Wednesday
Thursday
5
Friday
6
7
Saturday
Sunday
Press
3.
mode and select P3. press
. Press
and
to set from
(Monday-Sunday).
to confirm and enter hour setting:
The screen will display
. Press
for every hour. Comfort mode
4.
for 3 secs to enter day setting:
and
to select the hour from 00-24. Press
or ECO mode
to choose heating mode
.
Repeat the operation until you have completed the schedule of every hour and every day.
Notes: After setting heating mode for hour 23, press
When screen displays
And
, press
to set
to come back to day setting.
scheduling.
BUTTONS
Use these buttons to increase or decrease the target temperature, and to increase or decrease time within timer
function
This feature can be performed using the TCP Smart App.
TIMER BUTTON
24 Hr Timer
Press once, the screen will display “
” and will keep flashing. Press
and
to set timer from 0-24
hours. Wait 3 seconds to confirm setting. From the moment the time is set, the timer will then continue to count down. During
the countdown, when the target temperature is reached, the towel heater will turn off. Once the heater detects a fall in actual
room temperature it will restart. Once the countdown is ended the heater will turn off completely.
Pre-Set Quick Timer
Press
one time, the screen will display “
”, press
once to select the desired time either
2Hrs, 4Hrs, 6Hrs or 8Hrs. From the moment the time is set, the timer will then continue to count down. During the countdown,
when the target temperature is reached, the towel heater will turn off. Once the heater detects a fall in actual room temperature
it will restart. Once the countdown is ended the heater will turn off completely.
This feature can be performed using the TCP Smart App.
Clock and day of the week setting
Press the
button for 3 seconds. The screen display will show”
”. Press
and
to select the day:
The number displayed will correspond to the day of the week as below:
1
2
3
4
5
6
7
Press
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
to confirm the day and enter the clock hour setting. The screen will display
time. Press
MINUTE time.
. Press
to confirm the time set and enter minute setting with the screen displaying
. Press
and
to set the HOUR
and
to set the
OPEN WINDOW FUNCTION
When the ambient temperature drops by 5°C within 10 minutes, the heater will register the possibility of an open window in
the room. If this happens, it will stop heating and enter standby mode.
To turn on open window function, press Mode and + buttons together and the screen will display
screen will display the set temperature.
, after 3 seconds, the
To turn off open window function, press Mode and - buttons together and the screen will display
screen will display the set temperature.
, after 3 seconds, the
CLEANING THE HEATER
Allow heater to cool down before cleaning. Clean the outside of the heater by wiping with a damp cloth and buff with
a dry cloth. Do not use anydetergents or abrasives.
CORRECT DISPOSAL OF THIS PRODUCT
WARRANTY INFORMATION
The manufacturer provides warranty in accordance with the legislation of the customer’s own countryof residence, with a
minimum of 2 year, starting from the date on which the appliance is sold to the end user.
The warranty only covers defects in material or workmanship.
The repairs under warranty may only be carried out by an authorized service centre. When making aclaim under the
warranty, the original bill of purchase (with purchase date) must be submitted. The warranty will not apply in cases of:
-
Normal wear and tear
Incorrect use, e.g. overloading of the appliance, use of non-approved accessories
Use of force, damage caused by external influences
-
Damage caused by non-observance of the user manual, e.g. connection to an unsuitablemains supply or
non-compliance with the installation instructions
Partially or completely dismantled appliances.
CERTIFICATION CONFORMITY
Hereby, Technical Consumer Products Ltd declares that the radio equipment type TCP Smart
Wifi Tower Fan 2000W – White is in accordance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address –
https://tcpsmart.eu/compliance-data
REGISTERED OFFICES
TCP UK Ltd, 1 Exchange Court, Cottingham Road, Corby, Northants, NN17 1TY.
TCP France, Quai Gabriel P’ri, 1, Joinville Le Point, France, 94340.
CONNECTING THE APPLIANCE TO WI-FI
Use the QR code below to download the TCP Smart App for control of the heater by voice or TCPSmart App.
QR code for both android and iOS
To control the heater using the TCP Smart App the unit must be turned on. Before you get
started you will need the following:
•
Smart device such as a mobile phone
•
Access to the Google or Apple App store, log on and passwords
•
The name of your Wi-Fi network and password to your Wi-Fi network
•
Confirm your home Wi-Fi router is running on 2.4Ghz and not 5Ghz. If you are unsure,please consult
your broadband provider for details on how to change the settings.
•
Turn off any Wi-Fi extenders during set up
•
Check you do not have any limitations on the number of devices with your broadbandprovider
Please note: Our products do not work on 5Ghz only 2.4Ghz.
For instructions on how to connect to Amazon Alexa or Google Nest please visit https://www.tcpsmart.eu/howto-alexa-google-nest
With the heater turned on, hold down the M o d e button
f o r 3 s e c o n d s until it bleeps and the W i F i LED light
blinks rapidly, the device is now in paring mode. In the TCP Smart App, enter your WiFi password and follow the
instructions in the App to connect.
USING THE APPLIANCE W H E N C O N N E C T E D TO WIFI
Main screen showing functions
Other Functions
Inc Open widow detection,
Temperature calibration & App
background colour
On/Off
Target Temperature
Night Light
Target Temperature Setting
24 Hr Timer
Mode Selection
Room Temperature
Scheduling
Mode Selection Screen
Comfort mode
Eco mode
Preset Programming
Anti-Frost
Quick Timer
Schedule
Other functions
Select for following functions: Open Window Detection, Temperature Calibration and LCD Background colour.
Open window Detection
Press
on main screen. Slide
to main screen
button to left to turn on. Slide to right to turn off. Press < to return
Temperature Calibration
Use this function to manually adjust to the actual room temperature if it is not correct.
Use this function to manually adjust to the actual room temperature if it is not
correct.
Press
on main screen.
Change the temperature by using
or
buttons.
Once you have set the temperature press tick button to set and < to return to
previous screen.
Current room temperature is displayed on the main screen.
App background colour
Press other functions button
. To turn on slide the button
to change with target
temperature to the right. To turn off this function slide this button to the left. Press < to return to main screen.
Night Light
Press
to dim the LCD screen. Press again to return to normal brightness.
Target Temperature Setting
Use + and – buttons to set target temperature.
Timer
Use the + and – button to set a countdown, from 1 to 23 hours. From the moment the time is set, the timer will then continue
to count down. During the countdown, when the target temperature is reached, the towel heater will turn off. Once the heater
detects a fall in actual room temperature it will restart. Once the countdown is ended the heater will turn off completely.
For pre-set quick timer function see mode settings below.
Smart Scheduling
Press timer bar to take you to the below screen:
The scheduling can be selected as hourly
increments on separate days. When you
press the hour in any given day a temperature
bar will be displayed.
Use this to select the temperature for that
hour. Repeat as needed across each day /
each hour of the day. Press < to return to
main screen.
Note: Press Mode and
scheduling.
to activate
Mode
Select
to choose the following functions:
Comfort mode
- Set using the temperature scale on the main screen. Press < to return to main screen.
– this is a preset temperature which is 4°C below the comfort mode setting. Press < to return to main
Eco mode
screen.
Present Programme – see below
Present Programme – see below
Adjustable Programme – see below
P1 and P2 are pre-programmed schedules. P3 is a schedule that can be set to your own requirements. This is done via
the LCD screen on the heater using the steps below. Each programme can then be activated by pressing the
corresponding P1, P2 or P3 symbol. Press
to turn off. Press < to return to main screen.
Anti Frost
For this function to work the heater must be turned on. Once the Anti-frost mode is selected the target temperature will be
overridden and the heater will stay at 7°C until the anti-frost function is turned off. . Select
Press
to turn this function on.
to turn off. Press < to return to main screen.
Scheduling
Press
to turn on the scheduling you have selected. Press
to turn off. Press < to return to main screen.
Quick Timer
Select 2h, 3h or 4h for the heater to go into a countdown timer. From the moment the timer is set, the heater will continue
to count down. Once completed the Towel Radiator will switch off.
Once the target temperature is reached the towel heater will stay on until the countdown time is finished.
Press
to turn off ahead of the countdown time finishing. Press < to return to main screen.
TCP LTD, 1 EXCHANGE COURT, COTTINGHAM ROAD, CORBY, NN17 1EW

advertisement

Key Features

  • Smart WiFi control for remote access and scheduling
  • Comfort and Eco modes for energy efficiency
  • 24/7 hour programming for customized heating
  • LCD screen for easy operation
  • IP24 rated for safe use in bathrooms
  • Wall-mounted design for space-saving convenience

Related manuals

Frequently Answers and Questions

Where can I install the towel radiator?
You can install it in a bathroom, but only in Zone 3, which is the area above the bath to a height of basin (2.25m from the floor).
How do I connect the power supply cable?
Connect the blue wire to the terminal marked with an N or colored black, and the brown wire to the terminal marked with an L or colored red.
What safety precautions should I take?
Keep the power cord away from the hot body of the heater, and do not use it if it has been dropped or damaged.
Download PDF

advertisement