Compaq | Netelligent 1224 | User`s guide | Compaq Netelligent 1224 User`s guide

Pass-Through Expansion Kit
Installation Instructions
First Edition (May 1999)
Part Number ER-TL881-EA. A01/138255-001
Compaq Computer Corporation
Notice
The information in this publication is subject to change without notice.
COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL OR
EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN, NOR FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR
USE OF THIS MATERIAL. THIS INFORMATION IS PROVIDED “AS IS” AND COMPAQ
COMPUTER CORPORATION DISCLAIMS ANY WARRANTIES, EXPRESS, IMPLIED OR
STATUTORY AND EXPRESSLY DISCLAIMS THE IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, GOOD TITLE AND AGAINST
INFRINGEMENT.
This publication contains information protected by copyright. No part of this publication may be
photocopied or reproduced in any form without prior written consent from Compaq Computer
Corporation.
© 1999 Compaq Computer Corporation.
All rights reserved. Printed in the U.S.A.
The software described in this guide is furnished under a license agreement or nondisclosure agreement.
The software may be used or copied only in accordance with the terms of the agreement.
Compaq, Deskpro, Fastart, Compaq Insight Manager, Systempro, Systempro/LT, ProLiant, ROMPaq,
QVision, SmartStart, NetFlex, QuickFind, PaqFax, ProSignia, registered United States Patent and
Trademark Office.
Neoserver, Netelligent, Systempro/XL, SoftPaq, QuickBlank, QuickLock are trademarks and/or service
marks of Compaq Computer Corporation.
Microsoft, MS-DOS, Windows, and Windows NT are registered trademarks of Microsoft Corporation.
Pentium is a registered trademark and Xeon is a trademark of Intel Corporation.
Other product names mentioned herein may be trademarks and/or registered trademarks of their
respective companies.
Pass-Through Expansion Kit Installation Instructions
First Edition (May 1999)
Part Number ER-TL881-EA. A01/138255-001
Contents
About This Guide
Text Conventions ....................................................................................................v
Symbols in Text .................................................................................................... vi
Symbols on Equipment.......................................................................................... vi
Rack Stability....................................................................................................... vii
Getting Help ........................................................................................................ vii
Compaq Technical Support.......................................................................... viiii
Compaq Website .......................................................................................... viii
Compaq Authorized Reseller .......................................................................... ix
Chapter 1
Overview
Mechanism Section Covers ................................................................................. 1-1
Parts and Tools.................................................................................................... 1-2
Chapter 2
Upgrade Procedure
Assembly Procedures .......................................................................................... 2-1
Identifying the Parts of the Mechanism ......................................................... 2-1
Orienting the Parts During Assembly............................................................ 2-4
Assembling the Mechanism .......................................................................... 2-5
Installing the Belt ......................................................................................... 2-7
Adding Sections to an Existing Mechanism ....................................................... 2-11
Index
iv Pass-Through Expansion Kit Installation Instructions
List of Figures
Figure 1-1. Cover Assembly Side Plate............................................................... 1-2
Figure 1-2. Mechanism Section Cover ................................................................ 1-2
Figure 2-1. Mechanism External Parts ................................................................. 2-2
Figure 2-2. Mechanism Car ................................................................................ 2-3
Figure 2-3. Car Rear View Showing Belt Block.................................................. 2-3
Figure 2-4. Assembled Mechanism..................................................................... 2-5
Figure 2-5. Tensioner Ramp and Idler Pulley...................................................... 2-7
Figure 2-6. Threading the Belt Around the Motor Drive Pulley ........................... 2-8
Figure 2-7. Belt Ends ......................................................................................... 2-9
Figure 2-8. Belt Block with Belt in Place ...........................................................2-10
Figure 2-9. Aligning the Captive Screws with the Belt Block .............................2-11
List of Tables
Table 1-1 Upgrade Kit 120880–B31 Parts............................................................ 1-3
Table 2-1 Required Belt Length........................................................................... 2-8
About This Guide
This guide is designed to be used as step-by-step instructions for installation
and as a reference for operation, troubleshooting, and future upgrades.
Text Conventions
This document uses the following conventions to distinguish elements of text:
Keys
Keys appear in boldface. A plus sign (+) between
two keys indicates that they should be pressed
simultaneously.
USER INPUT
User input appears in a different typeface and in
uppercase.
FILENAMES
File names appear in uppercase italics.
Menu Options,
Command Names,
Dialog Box Names
These elements appear in initial capital letters.
COMMANDS,
DIRECTORY NAMES,
and DRIVE NAMES
These elements appear in uppercase.
Type
When you are instructed to type information, type
the information without pressing the Enter key.
Enter
When you are instructed to enter information, type
the information and then press the Enter key.
vi Pass-Through Expansion Kit Installation Instructions
Symbols in Text
These symbols may be found in the text of this guide. They have the following
meanings.
WARNING: Text set off in this manner indicates that failure to follow directions
in the warning could result in bodily harm or loss of life.
CAUTION: Text set off in this manner indicates that failure to follow directions
could result in damage to equipment or loss of information.
IMPORTANT: Text set off in this manner presents clarifying information or specific
instructions.
NOTE: Text set off in this manner presents commentary, sidelights, or interesting points
of information.
Symbols on Equipment
These icons may be located on equipment in areas where hazardous conditions
may exist.
Any surface or area of the equipment marked with these symbols
indicates the presence of electrical shock hazards. Enclosed area
contains no operator serviceable parts.
WARNING: To reduce the risk of injury from electrical shock hazards,
do not open this enclosure.
Any RJ-45 receptacle marked with these symbols indicates a Network
Interface Connection.
WARNING: To reduce the risk of electrical shock, fire, or damage to
the equipment, do not plug telephone or telecommunications
connectors into this receptacle.
About This Guide vii
Any surface or area of the equipment marked with these symbols
indicates the presence of a hot surface or hot component. If this
surface is contacted, the potential for injury exists.
WARNING: To reduce the risk of injury from a hot component, allow
the surface to cool before touching.
Power Supplies or Systems marked with these symbols
indicate the equipment is supplied by multiple sources of
power.
WARNING: To reduce the risk of injury from electrical shock,
remove all power cords to completely disconnect power from
the system.
Rack Stability
WARNING: To reduce the risk of personal injury or damage to the equipment,
be sure that:
■
The leveling jacks are extended to the floor.
■
The full weight of the rack rests on the leveling jacks.
■
The stabilizing feet are attached to the rack if it is a single rack
installations.
■
The racks are coupled together in multiple rack installations.
■
A rack may become unstable if more than one component is extended for
any reason. Extend only one component at a time.
Getting Help
If you have a problem and have exhausted the information in this guide, you
can get further information and other help in the following locations.
viii Pass-Through Expansion Kit Installation Instructions
Compaq Technical Support
You are entitled to free hardware technical telephone support for your product
for as long you own the product. A technical support specialist will help you
diagnose the problem or guide you to the next step in the warranty process.
In North America, call the Compaq Technical Phone Support Center at
1-800-OK-COMPAQ1. This service is available 24 hours a day, 7 days a week.
Outside North America, call the nearest Compaq Technical Support Phone
Center. Telephone numbers for world wide Technical Support Centers are
listed on the Compaq website. Access the Compaq website by logging on to
the Internet at http://www.compaq.com.
Be sure to have the following information available before you call Compaq:
■
Technical support registration number (if applicable)
■
Product serial number (s)
■
Product model name(s) and numbers(s)
■
Applicable error messages
■
Add-on boards or hardware
■
Third-party hardware or software
■
Operating system type and revision level
■
Detailed, specific questions
Compaq Website
The Compaq website has information on this product as well as the latest
drivers and Flash ROM images. You can access the Compaq website by
logging on to the Internet at http://www.compaq.com.
1
For continuous quality improvement, calls may be recorded or monitored.
About This Guide ix
Compaq Authorized Reseller
For the name of your nearest Compaq Authorized Reseller:
■
In the United States, call 1-800-345-1518.
■
In Canada, call 1-800-263-5868.
■
Elsewhere, see the Compaq website for locations and telephone
numbers.
blank
Chapter
1
Overview
This document provides instructions for the addition of sections to the PassThrough mechanism (“the mechanism”) in a TL881 MiniLibrary system. It is
intended to be used in conjunction with the Compaq Upgrade Kit, part number
120880–B31
IMPORTANT: These procedures should be performed by a qualified service technician.
Mechanism Section Covers
The Pass-Through mechanism moves tape cartridges vertically between
TL881 MiniLibrary modules. Each module section is covered by an individual
sheet-metal enclosure. These covers protect the mechanism during shipping
and are an important safety shield during operation.
A separate detachable side plate is part of the cover assembly. During
installation the side plates should be removed on any mechanism sections
located behind a MiniLibrary module; this allows easy access to a cartridge
stranded in transit by a commercial power outage. The remaining portion of
the cover can be removed also from any section behind a module.
IMPORTANT: Both parts of the covers must remain in place over any section of the
mechanism that is not behind a MiniLibrary module. Any gaps between modules should
remain completely covered.
1-2 Pass-Through Expansion Kit Installation Instructions
Figure 1-1 shows the cover assembly side plate (1) and Figure 1-2 shows the
mechanism section cover (2).
1
SHR-1224
Figure 1-1. Cover Assembly Side Plate
2
SHR-1225
Figure 1-2. Mechanism Section Cover
Overview 1-3
Parts and Tools
You need the parts and tools described here. The upgrade kit, part number
120880–B31, contains the parts listed in Table 1-1.
Table 1-1
Upgrade Kit 120880–B31 Parts
Kit Parts
Part Number
1 Instructions (this document)
104159-101
2 Extension Sections
968224-101
2 Safety Covers
968013-101
2 Cover Plates
968026-101
2 Belts
968257-101
1 Support Brace
968216-101
4 Tie Bars
968216-101
8 Button Rivets, Nylon
972502-101
2 M3 x 8 mm sems Phillips pan head
screws
970945-308
16 M3 x 20 mm sems Phillips pan head
screws
970945-320
1 Kit Contains: Angle brackets; Nut plates;
Screws and lock washers for mounting
slides; And screws for fastening support
braces to slides
606619-002
2 RS-232 Cable Assemblies
968239-004
You need these tools:
■
Flat-head screwdriver
■
No. 1 Phillips screwdriver
■
No. 2 Phillips screwdriver
■
Utility knife
■
0.050" Allen wrench or paper clip
blank
Chapter
2
Upgrade Procedure
Assembly Procedures
Assembly of the Pass-Through mechanism (“the mechanism”) requires
experience working with moderately complex mechanisms, and the ability to
follow directions carefully. The following sections first provide an overview
of the parts and procedures required to assemble and install the mechanism. It
will be useful to read these sections through before beginning work. The most
common procedure required in the field, adding a section or sections to an
existing mechanism, is described in a separate section following the overview.
It refers to some of the procedures described in the overview.
Identifying the Parts of the Mechanism
Locate and identify the mechanism internal and external parts. The mechanism
includes the following external parts (Figure 2-1).
■
Motor drive section (1)
■
Extension sections (2)
■
Mechanism base with idler pulley (3)
■
Tie bars (4)
■
Support brace (5)
■
Left and right rack slide extensions (6)
Compaq Confidential – Need to Know Required
Writer: Don Kaplan Project: Pass-Through Mechanism Expansion Kit Installation Instructions Comments:
Part Number: ER-TL881-EA. A01/138255-001 File Name: C-CH2 UP.DOC Last Saved On: 5/13/99 10:01 AM
2-2 Pass-Through Mechanism Expansion Kit Installation Instructions
■
Angle brackets (7)
■
L-shaped nut plates (8).
1
5
2
8
5
7
6
4
6
8
4
8
3
5
6
8
4
SHR-1233
Figure 2-1. Mechanism External Parts
NOTE: The slide extensions, (6) in Figure 2-1, are not enclosed with the mechanism
parts. They are supplied as part of the installation hardware for the slides that come with
each of the modules.
The rails for each rack type might be different but the mounting scheme is the same.
If you are installing a module, follow the instructions for installing rack slides
that appear in both the System User’s Guide and the Service Manual for the
TL881 MiniLibrary system. After the rack slides and the slave modules are in
place, and after the mechanism is assembled, you will install the mechanism in
the rack by attaching the support braces (5) to the slide extensions (6) using
the angle brackets (7) and L-shaped nut plates (8).
The internal parts you will need to recognize during assembly, the car and the
belt block, are shown in Figures 2-2 and 2-3; Figure 2-3 locates the belt block
(1) and the captive screws (2).
Compaq Confidential – Need to Know Required
Writer: Don Kaplan Project: Pass-Through Mechanism Expansion Kit Installation Instructions Comments:
Part Number: ER-TL881-EA. A01/138255-001 File Name: C-CH2 UP.DOC Last Saved On: 5/13/99 10:01 AM
Upgrade Procedure 2-3
SHR-1234
Figure 2-2. Mechanism Car
1
2
SHR-1235
Figure 2-3. Car Rear View Showing Belt Block
Compaq Confidential – Need to Know Required
Writer: Don Kaplan Project: Pass-Through Mechanism Expansion Kit Installation Instructions Comments:
Part Number: ER-TL881-EA. A01/138255-001 File Name: C-CH2 UP.DOC Last Saved On: 5/13/99 10:01 AM
2-4 Pass-Through Mechanism Expansion Kit Installation Instructions
The belt block is fastened to the back of the car with two captive screws
(Figure 2-3). Make a careful note of the orientation of the block with respect to
the car.
Orienting the Parts During Assembly
To determine the orientation of an extension section examine the flanges on
the edges of the section and note that they are dissimilar. Position the section
so that its orientation matches that of the elevator base.
Figure 2-4 shows a typical mechanism assembly. The motor drive section
always goes on top, and the base section with the idler pulley always goes on
the bottom. Extension sections are mounted between the motor drive section
and the base section. All sections are joined together with tie bars. For systems
up to four sections, two support braces are needed, one attached to the motor
drive and one to the base section. For larger systems, a third support brace
should be mounted near the center of the mechanism, as shown in Figure 2-4.
Compaq Confidential – Need to Know Required
Writer: Don Kaplan Project: Pass-Through Mechanism Expansion Kit Installation Instructions Comments:
Part Number: ER-TL881-EA. A01/138255-001 File Name: C-CH2 UP.DOC Last Saved On: 5/13/99 10:01 AM
Upgrade Procedure 2-5
2
1
1
3
4
5
1
SHR-1236
™ Support brace; š Motor section drive; › Extension section; œ Tie bar;
 Base section.
Figure 2-4. Assembled Mechanism
Assembling the Mechanism
You need a clean, flat work area such as a table or work bench. The surface
should be long enough to support the full height of the mechanism. The height
is equal to the height of the stack of modules in your system plus any gaps you
intend to include in the stack.
Do the following steps to assemble the mechanism. Even though in most cases
you are adding to a previously-assembled mechanism, it will help if you take a
few minutes to read this section and the next section on installing the belt
before you proceed to the section entitled Adding to an Existing Mechanism.
Compaq Confidential – Need to Know Required
Writer: Don Kaplan Project: Pass-Through Mechanism Expansion Kit Installation Instructions Comments:
Part Number: ER-TL881-EA. A01/138255-001 File Name: C-CH2 UP.DOC Last Saved On: 5/13/99 10:01 AM
2-6 Pass-Through Mechanism Expansion Kit Installation Instructions
1. Place the base section (Figures 2-1 and 2-4), with the inside facing
down, overhanging the right end of the work area, with the bottom plate
of the section toward the right.
2. Place each of the extension sections, with the inside facing down, in a
row aligned edge-to-edge beginning with the base section. The bottoms
of the sections should be toward the right. Omit the motor drive at this
time.
3. Align a support brace over the holes on the rear of the base section
(Figure 2-4).
4. Insert two M4 x 20 mm Phillips sems screws through the holes in the
support brace into the holes in the base section; tighten the screws.
5. Place pairs of tie bars so that they straddle all of the joints where
sections come together. Be sure that the beveled edge is toward the
inside corner of the sections.
6. Install two M3 x 20 mm Phillips sems screws through each tie bar into
the threaded holes in the flanges of the extension sections; tighten the
screws finger tight only.
7. Insert two M3 x 20 mm sems screws through each tie bar into the side of
the extension sections; tighten the screws finger-tight only.
8. Press the base section and the first extension section together firmly;
then tighten the screws alternately, first the two into the flanges of the
base section and the extension section, and then the two into the sides of
the base section and the extension section, so that each tie bar is drawn
into the inside corner of the sections.
IMPORTANT: Be careful not to overtighten these screws.
9. Inspect the joint where the sections come together to ensure that the
sections are aligned well. If there is a gap or misalignment, do Step 8
again.
10. Do Steps 8 and 9 for each extension section you add.
NOTE: It might be necessary to use suitable blocks to support the row of sections so that
neither the motor housing not the bottom flange of the base section touch the work
surface while you are connecting the motor drive section.
11. Align a support brace over the holes on the rear of the motor drive
section (Figure 2-4).
12. Insert two M4 x 20 mm Phillips sems screws through the support brace
into the holes in the motor drive section; tighten the screws.
Compaq Confidential – Need to Know Required
Writer: Don Kaplan Project: Pass-Through Mechanism Expansion Kit Installation Instructions Comments:
Part Number: ER-TL881-EA. A01/138255-001 File Name: C-CH2 UP.DOC Last Saved On: 5/13/99 10:01 AM
Upgrade Procedure 2-7
Installing the Belt
Do these steps to install the belt.
1. Turn the assembled mechanism over so that the motor points upward.
2. Locate the tensioner ramp in the base section (Figure 2-5). Compress the
spring until the hole in the tensioner ramp is aligned with a hole in the
base section. Insert an 0.050" Allen wrench or a paper clip through the
holes; this sets the idler pulley for zero belt tension.
3. Locate the length of toothed belt that was enclosed with the extension
section. Table 2-1 lists the required length of belt for your system. Make
sure you have the right length; if you do, cut the belt anywhere between
two teeth.
4. With the toothed side of the belt toward you position the right end of the
belt about halfway along the elevator.
SHR-1238
Figure 2-5. Tensioner Ramp and Idler Pulley
5. Thread the left end of the belt counter-clockwise around the motor drive
pulley (Figure 2-6).
Compaq Confidential – Need to Know Required
Writer: Don Kaplan Project: Pass-Through Mechanism Expansion Kit Installation Instructions Comments:
Part Number: ER-TL881-EA. A01/138255-001 File Name: C-CH2 UP.DOC Last Saved On: 5/13/99 10:01 AM
2-8 Pass-Through Mechanism Expansion Kit Installation Instructions
6. Move the left end of the belt to the right and thread it around the idler
pulley (Figure 2-5) and back to meet what started out as the right end of
the belt. When you hold the two ends of the belt, they should be
touching or very slightly overlapping (Figure 2-7).
Table 2-1
Required Belt Length
Number of Extensions (Base, Motor
Drive, Extension)
Length of Belt
2
27 inches
3
41 inches
4
55 inches
5
69 inches
6
83 inches
SHR-1237
Figure 2-6. Threading the Belt Around the Motor Drive Pulley
Compaq Confidential – Need to Know Required
Writer: Don Kaplan Project: Pass-Through Mechanism Expansion Kit Installation Instructions Comments:
Part Number: ER-TL881-EA. A01/138255-001 File Name: C-CH2 UP.DOC Last Saved On: 5/13/99 10:01 AM
Upgrade Procedure 2-9
SHR-1239
Figure 2-7. Belt Ends
7. Locate the belt block and the four screws that hold the belt retaining
plates to the block (Figure 2-8). Loosen the four screws and slide the
ends of the belt under the plates until they engage the teeth on the block;
both ends of the belt should be visible through the gap between the
plates. Set the belt so there is only a small space between the ends of the
belt (about 1/32").
8. Tighten the four screws that hold the belt retaining plates.
9. Pull out the Allen wrench or the paper clip from the base section; now
the proper tension is applied to the belt.
Compaq Confidential – Need to Know Required
Writer: Don Kaplan Project: Pass-Through Mechanism Expansion Kit Installation Instructions Comments:
Part Number: ER-TL881-EA. A01/138255-001 File Name: C-CH2 UP.DOC Last Saved On: 5/13/99 10:01 AM
2-10 Pass-Through Mechanism Expansion Kit Installation Instructions
2
1
3
SHR-1240
™ Belt; š Visible gap; › Block.
Figure 2-8. Belt Block with Belt in Place
10. Open the door of the car and locate the two captive screws. Figure 2-9
shows the screws, (2), and also shows the car in the track, although at
the time of this step the car has not yet been installed in the track (the
figure also shows the car without the door for clarity; don’t remove the
door)
11. Turn each screw counter-clockwise until about one thread width is
embedded in the car bracket and the screws are held in an upright
position.
12. Position the belt block at least six inches from the motor drive pulley.
13. Now you must position the car in the mechanism so it appears as shown
in Figure 2-9. Tilt the car so that you can engage the spring-loaded
wheels in the track as shown, and position the car so the captive screws
are directly over the holes in the belt block.
14. While holding the tilted car in place with one hand, grasp the belt with
the other hand several inches from the belt block as shown in Figure 29, and push the belt down (1) until the belt block is pressed against the
back of the mechanism.
15. Continue to push the belt down while at the same time compressing the
springs and rotating the fixed wheels downward until the fixed wheels
are engaged in the other track as shown in the figure, and the captive
screws are just protruding into the holes in the belt block; release the car
and make sure all the wheels are engaged in the track grooves (continue
to press the belt block against the back of the mechanism).
Compaq Confidential – Need to Know Required
Writer: Don Kaplan Project: Pass-Through Mechanism Expansion Kit Installation Instructions Comments:
Part Number: ER-TL881-EA. A01/138255-001 File Name: C-CH2 UP.DOC Last Saved On: 5/13/99 10:01 AM
Upgrade Procedure 2-11
2
1
SHR-1198
Figure 2-9. Aligning the Captive Screws with the Belt Block
16. Begin to tighten the captive screws. When both screws are threaded into
the belt block partially, release the belt and then continue to tighten the
screws until the belt block is seated firmly against the car bracket. Close
the car door and secure it.
17. Using nylon button rivets install safety covers over any exposed
mechanism sections that will not be covered by modules.
18. If you have not already installed all new modules, go to the section
entitled Mounting the Module Rack Slides in the System User’s Guide
that was enclosed with the module.
NOTE: The 10-32 pan head screws and lock washers required to mount the slides in the
rack are included in Kit 606619-001, which is one of the items in this kit.
Adding Sections to an Existing
Mechanism
Before you do this procedure read through the two preceding sections,
Assembling the Mechanism and Installing the Belt; it will help you to
Compaq Confidential – Need to Know Required
Writer: Don Kaplan Project: Pass-Through Mechanism Expansion Kit Installation Instructions Comments:
Part Number: ER-TL881-EA. A01/138255-001 File Name: C-CH2 UP.DOC Last Saved On: 5/13/99 10:01 AM
2-12 Pass-Through Mechanism Expansion Kit Installation Instructions
understand how to do the steps in this section. To add to an existing
mechanism you must first disassemble the mechanism partially, then make the
necessary changes using procedures described in the preceding sections. Do
the following steps.
1. Locate the support braces on the mechanism (Figures 2-1 and 2-4). To
remove the assembly from the rack disconnect the cable that is
connected to the motor drive assembly, then remove the two screws that
fasten each support brace to angle brackets at the ends. Pull the
mechanism straight back until it is clear of the modules.
2. Locate the safety covers over the drive motor section and the base
assembly. Note that the covers are held in place by nylon button rivet
fasteners. Using a suitable thin-bladed tool, pry up the cover until the
fasteners can be removed. Set the covers aside and save the fasteners for
later use.
3. Place the mechanism on a suitable work surface with the motor at the
left and pointed upward.
4. Open the door of the car to gain access to the captive screws (Figure
2-9), but do not remove the door. Loosen the captive screws until they
are disengaged from the belt block.
5. Grasp the far side of the car and pull it toward you to compress the
springs until the wheels on the far side are free of the track groove; then
rotate the far side of the car up, decompress the springs to free the
near-side wheels from their track grooves, and remove the car.
6. Locate the tensioner ramp in the base section (Figure 2-5). Compress the
spring until the hole in the tensioner ramp is aligned with a hole in the
base section. Insert an 0.050" Allen wrench or a paper clip through the
holes. This sets the idler pulley for zero belt tension.
7. Loosen the four screws on the belt block (Figure 2-8) enough so that
you can pull the ends of the belt free of the block.
8. Pull the belt free of the motor drive assembly and the base section and
set the belt aside.
9. Turn the mechanism over and support it so that neither the motor nor the
flange at the bottom of the base assembly is touching the work surface.
10. Remove the eight screws that hold a pair of tie bars in place and separate
the mechanism at that joint.
11. You can now add sections as needed and install a new belt, as described
in Assembling the Mechanism and Installing the Belt.
NOTE: If you are adding a section and do not intend to install a TL881 MiniLibrary module
in front of that section, regulatory agency safety regulations required that you install a
safety cover over the exposed section.
Compaq Confidential – Need to Know Required
Writer: Don Kaplan Project: Pass-Through Mechanism Expansion Kit Installation Instructions Comments:
Part Number: ER-TL881-EA. A01/138255-001 File Name: C-CH2 UP.DOC Last Saved On: 5/13/99 10:01 AM
Index
B
belt block 2-2
Compq authorized resellers,
telephone numbers viii
technical support telephone
numbers vii
http://www.compaq.com viii
C
captive screws 2-2
car 2-2
Compaq authorized reseller viii
compaq upgrade kit
part number 1-1
parts 1-1
I
icons
symbols on equipment vi
L
length of belt 2-7
E
elevator
external parts 2-1
internal parts 2-2
existing mechanism 2-13
G
M
mechanism assembly
base section 2-4
extension section 2-4
motor drive section 2-4
support brace 2-4
tie bar 2-4
getting help vii
P
H
parts and tools 1-2
help
additional sources vii
Compaq website viii
2 Pass-Through Mechanism Expansion Kit Installation Instructions
R
tools 1-3
RJ-45 receptacle vi
U
S
upgrade kit part number 1-2
section covers 1-1
symbols in text vi
symbols on equipment vi
W
T
technical support viii
telephone numbers viii
tensioner ramp 2-7
text conventions v
warnings
electrical shock vii
rack stability vii
work area 2-6
www.compaq.com. viii
Download PDF