GE Profile PFD87GSSVWH Capacity Smart Front Load Gas Dryer Instruction manual

Add to My manuals
4 Pages

advertisement

GE Profile PFD87GSSVWH Capacity Smart Front Load Gas Dryer Instruction manual | Manualzz
PFD87GSSVWW/SPVRS
GE Profile™ 7.8 cu. ft. Capacity Smart Front Load Gas Dryer
with Steam and Sanitize Cycle
Stacked:
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
GAS DRYER RATING
120V
60Hz, 8A
Pedestal:
Riser:
EXHAUST OPTIONS: 4-way via rear, left, right, and bottom.
(The right, left, and bottom venting options require Side Vent
Kit: GFA28DSVN)
79-1/2″
(202 cm)
CIRCUIT REQUIREMENTS: An individual, properly grounded
branch circuit, protected by a 15-20 amp circuit breaker or a
time-delay fuse, is required.
46-3/4″
NOTE: Dryer wall outlet must be located within 36" of service
cord entry and accessible when dryer is mounted in position.
INSTALLATION INFORMATION: For complete information,
see installation instructions packed with your dryer.
55-7/8″
(118.7 cm)
(141.8 cm)
16″
7″
ADA Compliant
56-1/2"
28″
(71.2 cm)
34"
(143.5 cm)
(86.4 cm)
*39-3/4″
(101 cm)
*With leveling legs retracted:
39-3/4" (101 cm).
With leveling legs fully extended:
40-5/8" (103.1 cm).
22-1/2"
(57.15 cm)
6-1/8"
Front View
Side View
3-5/8"
1-5/8"
Back View
11"
For answers to your Monogram, Café™, GE Profile™ or GE Appliances product questions,
visit our website at geappliances.com or call GE Answer Center ® Service, 800.626.2000.
Specification Revised 11/23
PFD87GSSVWW/SPVRS
GE Profile™ 7.8 cu. ft. Capacity Smart Front Load Gas Dryer
with Steam and Sanitize Cycle
SPECIAL INSTALLATION REQUIREMENTS:
DRYER ACCESSORIES**
STACKED INSTALLATION:
GE Part Number
WB64X5025
WH97X30578
WE02X29449
GFA28DSVN
WE25X20060
WX17X10001CA
GFP1528SNWW
GFP1528PNRS
GFR0728SNWW
GFR0728PNRS
GFA28KITN
– Brackets for stacking dryer over washer are not included with
the dryer. Order part no. GFA28KITN.
ALCOVE OR CLOSET INSTALLATION:
- If your dryer is approved for installation in an alcove or closet, it will
be stated on a label on the dryer back.
- The dryer MUST be exhausted to the outside.
- Minimum clearances between dryer cabinet and adjacent walls or
other surfaces are: 0" all sides and top.*
- Closet doors must be louvered or otherwise ventilated and must
contain a minimum of 60 sq. in. of open area equally distributed. If
this closet contains both a washer and a dryer, doors must contain
a minimum of 120 sq. in. of open area equally distributed.
Description
Touch-up Paint (White) .06 oz.
Touch-Up Paint (Royal Sapphire) – 0.6 oz
Dryer Rack Assembly
Side Vent Kit
Steam Kit
Vibration Pads
Pedestal Assembly (White)
Pedestal Assembly (Royal Sapphire)
Riser (White)
Riser (Royal Sapphire)
Stacking Kit
WARRANTY
- No other fuel-burning appliance shall be installed in the same
closet with a gas dryer.
Labor Warranty
Parts Warranty
BATHROOM OR BEDROOM INSTALLATION:
Limited 1-year entire appliance
Limited 1-year entire appliance
Limited 10-year motor
- The dryer MUST be exhausted to the outdoors.
- The installation must conform with the local codes, or in the
absence of local codes, with the National Electric Code and
National Fuel Gas Code, ANSI Z223 for gas dryers.
MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET
INSTALLATIONS:
Minimum clearances to combustible surfaces are: 0" all sides and
top.*
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES,
PLEASE CALL 1-800-GE-CARES.
*For improved performance, a 1/2" clearance is suggested on each side.
**Accessories sold separately.
28"
28"
28"
16"
16"
7"
28-7/8"
28-7/8"
PEDESTAL DIMENSIONS (IN INCHES)
The optional 16" pedestal raises the door
opening and height of the washer or dryer.
For answers to your Monogram, Café™, GE Profile™ or GE Appliances product questions,
visit our website at geappliances.com or call GE Answer Center ® Service, 800.626.2000.
28"
7"
28 7/16"
28 7/16"
RISER DIMENSIONS (IN INCHES)
The optional 7" riser raises the door opening and height
of the washer or dryer while remaining ADA compliant.
Specification Revised 11/23
PFD87GSSVWW/SPVRS
GE Dryer Vent
GE Dryer Vent
GE Profile™ 7.8 cu. ft. Capacity Smart Front Load Gas Dryer
with Steam and Sanitize Cycle
DRYER EXHAUSTING INFORMATION – METAL DUCT ONLY
For complete information, see installation instructions packed with your dryer.
DUCTING MATERIALS: For best performance, this dryer should be vented with 4" diameter all
rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid)
ducting can be used (PM08X10084 or PM08X10085). In special installations, it may be necessary
to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible
metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semirigid) ducting cannot be used AND where a 4" diameter can be maintained throughout the entire
length of the transition duct. Please see installation instructions packed with your dryer for complete
instructions when using flexible metal (foil type) ducting.
Best performance
Maximum length of 4"
dia. rigid metal duct
Exhaust hood type
A
A
A
4
4
B
B
Domestic
dryer models
2-1/2
2-1/2
EXHAUST LENGTH CALCULATION:
1.
Determine the number of 90° turns needed for your installation. If you exhaust
to the side or bottom of dryer, add one turn.
2.The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated
is shown in the table.
7.5 cu. ft.
capacity models
electric dryers
Number
of
90°
turns
0
1
2
3
4
A
4"
opening
90 ft.
60 ft.
45 ft.
35 ft.
25 ft.
B
2-1/2"
opening
60 ft.
45 ft.
35 ft.
25 ft.
15 ft.
A turn of 45° or less may be ignored. Two 45° turns within the duct length
should be treated as a 90° elbow.
A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
CAUTION: For personal safety do not terminate exhaust into a chimney, under any enclosed house
floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture
could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen
exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc.
The wall cap must also be located at least 12" above the ground or any other obstruction with the
opening pointed down.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES,
PLEASE CALL 1-800-GE-CARES.
For answers to your Monogram, Café™, GE Profile™ or GE Appliances product questions,
visit our website at geappliances.com or call GE Answer Center ® Service, 800.626.2000.
55" long
Power Cord
6-1/8
1-5/8
11
3-5/8
Dryer Vent
Specification Revised 11/23
PFD87GSSVWW/SPVRS
GE Profile™ 7.8 cu. ft. Capacity Smart Front Load Gas Dryer
with Steam and Sanitize Cycle
FEATURES AND BENEFITS
Steam Cycle – Refresh small loads and dewrinkle larger loads with the
power of steam.
Washer Link – Wirelessly links your washer to your dryer so you only
choose a setting once.
Built-in WiFi – Start, stop and monitor your laundry from anywhere
while receiving real-time notifications and updates.
Steam Sanitize – Sterilize clothing with elevated temperatures designed
to kill common household germs and bacteria, while using steam
technology to reduce wrinkles and odors.
Quick Dry – Quickly dries items and small loads for families on the go.
Reduce Static – Prevent static cling with a gentle mist near the end of
the cycle.
Wrinkle Care – Prevents wrinkles by extending the tumble without heat.
Damp Alert – Signals when delicate clothes reach the ideal dampness
level for ironing or final air drying.
Convenient 4-Way Venting – Flexible venting options allow venting
from the front, rear or either side with Kit GFA28DSVN.
Reversible Door – Easily reverse your washer and dryer doors for
superior installation flexibility.
Check Vent Notification – Receive a notification when the dryer vent
needs to be cleaned, ensuring safe operation and optimal drying
performance.
4-way Venting Option
For answers to your Monogram, Café™, GE Profile™ or GE Appliances product questions,
visit our website at geappliances.com or call GE Answer Center ® Service, 800.626.2000.
Specification Revised 11/23

advertisement

Related manuals

advertisement