This symbol is intended to
alert the user to the presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol is
intended to alert the
user to the presence of
important operating
and maintenance (servicing) instructions in the literature accompanying
the appliance.
IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:
WATER AND MOISTURE: Appliance should not be used near water (near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken
so that objects do not fall and liquids are not spilled into the enclosure through openings.
POWER SOURCES: The appliance should be connected to a power supply only of the type described
in the operating instructions or as marked on the appliance.
GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polarization means of an appliance is not defeated.
POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against them, paying particular attention
to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
SERVICING: The user should not attempt to service the appliance beyond that described in the
operating instructions. All other servicing should be referred to qualified service personnel.
FUSING: If your unit is equipped with a fuse receptacle, replace only with the same type fuse.
Refer to replacement text on the unit for correct fuse type.
SAFETY INSTRUCTIONS (EUROPEAN)
The conductors in the AC power cord are colored in accordance with the following code.
GREEN & YELLOW—Earth
BLUE—Neutral
BROWN—Live
U.K. MAIN PLUG WARNING: A molded main plug that has been cut off from the cord is
unsafe. NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED
OR CUT MAIN PLUG INTO A POWER SOCKET.
CARVIN ENGINEERING DATA
LIMITED WARRANTY
Your Carvin product is guaranteed against failure for ONE YEAR unless otherwise stated. Carvin will
service and supply all parts at no charge to the customer providing the unit is under warranty. Shipping
costs are the responsibility of the customer. CARVIN DOES NOT PAY FOR PARTS OR SERVICING OTHER
THAN OUR OWN. A COPY OF THE ORIGINAL INVOICE IS REQUIRED TO VERIFY YOUR WARRANTY.
Carvin assumes no responsibility for horn drivers or speakers damaged by this unit. This warranty
does not cover, and no liability is assumed, for damage due to: natural disasters, accidents, abuse,
loss of parts, lack of reasonable care, incorrect use, or failure to follow instructions. This warranty
is in lieu of all other warranties, expressed or implied. No representative or person is authorized to
represent or assume for Carvin any liability in connection with the sale or servicing of Carvin products. CARVIN SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
When RETURNING merchandise to the factory, you may call for a return authorization number. Describe
in writing each problem. If your unit is out of warranty, you will be charged the current FLAT RATE for
parts and labor to bring your unit up to factory specifications.
BR12 and BR15 BASS AMPS
OPERATING MANUAL
for percussive slap. The 1” Titanium HF Driver is fully adjustable from
a variable rear control. All enclosures are covered in durable black
DuraTuff II™ for your transporting protection.
BR12
POWER AMP
Pure, clean bass power is delivered to your speaker from the
BR12/BR15 series ultra-low distortion power amp. Turn-on muting,
short circuit and thermal overload circuits protect your speakers and
amp form accidental overloads. ( Note: It is normal for the amp to
get warm to the touch).
HELP SECTION
1) AMP WILL NOT TURN ON
Check the power to the amp. Check for tripped circuit breakers, unplugged extension cords or powerstrip switches that may be turned off. Check the fuse. If a dark brownish color or no wire can be
seen within the glass tube, then replace. The amp may be perfectly fine but occasionally a fuse
may blow because of high AC voltage surges. After the fuse has been replaced with the proper
Slow Blow value and if the fuse fails again, the amp will require servicing.
2) NO OUTPUT with POWER LED light ON
Check the speaker cable. If OK, it’s possible that a speaker jack is defective. Check the SEND &
RETURN jacks as one of these jacks could be defective. Insert a guitar cord between these two
jacks to test. Defective jacks will require servicing.
3) KEEP YOUR AMP LOOKING NEW
Use a damp cloth to wipe the controls on the front & rear chassis panels. Wipe dry! Brush the lint
off the Duratuff II™ covering.
RECEIVING INSPECTION—read before getting star ted
BR15
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL! THIS UNIT CONTAINS HIGH
RISK OF ELECTRIC SHOCK VOLTAGE INSIDE!
CAUTION
INSPECT YOUR AMP FOR ANY DAMAGE which may have occurred during shipping.
If any damage is found, please notify the shipping company and CARVIN immediately.
SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship your
unit, always use the original carton and packing material. This will provide the best possible protection during shipment. CARVIN and the shipping company are not liable for
any damage caused by improper packing.
SAVE YOUR INVOICE. It will be required for warranty service if needed in the future.
SHIPMENT SHORTAGE. If you find items missing, they may have been shipped separately. Please allow several days for the rest of your order to arrive before inquiring.
RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this manual
for your records. Keep your portion of the card and return the portion with your name
and comments to us, or you may register online at www.carvin.com/registration.
G E T T I N G S TA RT E D Q U I C K LY
Congratulations on your purchase of the Carvin BR12/BR15 bass
amplifier. For over 40 years we have been building bass amplifiers,
so you can expect award-winning performance from these compact professional bass systems.
Turn the amp on and volume off, set the tone controls at their mid
“0” center position, turn the compressor and noise gate off and set
the 5 band graphic EQ to the their center/mid positions. Plug your
amp into the AC voltage and then plug in your bass. Now, turn the
amp’s power switch ON and gradually raise the volume. Re-adjust
the contour and tone controls as needed and your ready to go.
BASS SIGNAL PROCESSING
The preamp of a bass amplifier is the key to great tone. The first item
in the amp’s signal chain is the internal Class A discrete preamp circuits. Class A preamps circuits are renown for their superior sonic
detail. Secondly, your BASS, MID sweep & TREBLE controls are powerful active circuits, which will add flexibility in generating your tone.
The BX120 head also features a 5 BAND GRAPHIC EQ allowing you to
put the final touches on your sound from specialized filters designed
just for the bass guitar.
The BR12 and BR15 continues with features that are only found in
the most comprehensive bass rigs. A COMPRESSOR, which is sought
out by most professionals, is featured because it controls the overall level of the amp regardless of where the volume control is set. You
can now control your peaks without the amp getting too loud or keep
the amp from distorting.
You may easily add to your signal processing with an effects processor to enhance your sound. Any device from a foot pedal to a full effects
rack can be plugged into the rear of the “buffered” Send / Receive
EFFECTS LOOP.
The preamp LINE/PHONES jack can also be used as a main output
from the preamp to send your signal to a mixing console or another
high powered amplifier, allowing you to use the full complement of
signal processing from your unit.
Freq. Response:
THD:
RMS Power:
Direct Out:
Contour:
Tone Controls:
(3 band with mid sweep)
Compressor:
Comp Thresh/Ratio:
5 Band Graphic EQ:
Cabinet Freq. Resp:
Cabinet Types:
Cabinet Construction:
Tweeter Attenuation:
Warranty:
Power Requirements:
Fuse:
Size and Weight
Footswitch:
20 Hz to 20k Hz ±3 dB
Typically less than .1%
120 watts @ 4 ohms
XLR jack, GND Lift, and Level
FLAT to 250Hz/-8DB MID Cut
LO: 80Hz ±12dB
MID: 200-2KHz ±12dB
HI: 8KHz ±12dB
up to 30dB reduction
-7 to -27 dB, 3:1 ratio
80Hz, 250Hz, 500Hz,
800Hz, & 2kHz, ±12dB
BR12: 50 Hz to 16k Hz BR15: 41 Hz to 16k Hz
Sealed enclosure
Baltic Birch Plywood
Continuously variable
One Year
120VAC, 225VA
240VAC, 225VA
5A 250V slow blow
BR12: 17.5Wx12Dx25H. 36 lbs. BR15:19.3Wx14.9Dx24H. 46 lbs.
FS22, mute and EQ
COMBO CABINET DESIGN
For your records, you may wish to record the following information.
Part of the success of the BR12/BR14 combo amplifiers are their lightweight design and high performance. A cabinet tuned to the speakers parameters in each system adds to the speaker’s efficiency in the
35 Hz to 50 Hz range, resulting in overall warmth and a bigger,
rounder sound. The BRseries combo’s also feature a 1”Titanium HF
Driver to extend the upper range to 16k Hz, enhancing the harmonics
Serial No._____________________ Invoice Date_______________
76-42120A 1106
https://manual-hub.com/
Specifications:
12340 World Trade Drive, San Diego, CA 92128
800.854.2235 www.carvin.com
FRONT & REAR PANEL CONTROLS
19
19
1
2
3
4
5
6
9
7
8
7
1. INPUT JACK
The 1/4" phone jack is an instrument input designed to handle both active and
passive basses in connection with the Active Switch.
10
11
you play your bass. Now turn the GAIN to the full left and re-sweep the FREQ.
control and notice the mids disappear at different frequencies. There are many
variables as you can hear, so write down some of the settings for future reference. The mid sweep system is designed for fine tuning your overall sound.
ADJUSTING THE GRAPHIC EQ SLIDERS:
The best way to use the GRAPHIC EQ is to set all the sliders to their center
detent positions. When the sliders are in this position, they do no affect the audio
signal. After playing in this “flat” setting for a few minutes, raise one slider (to
boost) and play a broad range of notes to hear the change. Then lower the same
slider pass the center detent (to cut), play a few notes to hear the change and
return the slider to the center position. Try this with each slider to hear what
they do, then go back and adjust them together if needed for your sound.
2. BLUE JEWEL LIGHT
The Blue jewel light indicates the power is on.
3. DRIVE CONTROL
The DRIVE control adjusts the input level to the class A preamps. The Drive
control serves two purposes. The first half of the knob, 0-5, can be used to adjust
the input sensitivity for the differences in bass pickups. The second half of the
knob, 5-10, will increase the harmonic content of the tone. The closer to 10 the
more overdrive the tone will become. The drive knob will increase the volume
of the amplifier, so use it in combination with the master volume to achieve the
desired amplifier volume.
4. MUTE SWITCH
The MUTE switch mutes the output of the amplifier. A blue LED indicates the
MUTE switch is on. The mute switch is ideal for changing basses while the amp
is on and silent tuning on stage, since the rear tuner output is not muted. The
mute feature can also be switched with an FS22 footswitch.
5. ACTIVE SWITCH
Flip the active switch to the down “OFF” position for standard passive bass
pickups. If your bass uses a battery with an onboard active preamp, put the switch
in the up position. A blue LED indicates the ACTIVE switch is on.
6. CONTOUR CONTROL
The contour control provides a variable mid range scoop. When this control is
set to “FLAT” there is no change to the mid range frequencies. As you turn the
contour control clockwise, a mid range cut is scooped at 250Hz. When the contour control is set to maximum, the mid-range is cut at -9dB at 300Hz.
7. BASS AND TREBLE TONE CONTROLS
The BASS and TREBLE tone controls are custom shaped controls to deliver punchy
lows and crisp tight highs for a variety of bass sounds.
When the BASS control is turned to the right, it boosts the signal and when
turned to the left cuts the signal. The effected frequencies are centered at 80Hz
and can deliver a great deal of volume. Be careful not to distort the output.
When the TREBLE control is turned to the right, it boosts the signal and when
turned to the left, it cuts the signal. The boosted frequency for the TREBLE control is centered at 8k Hz.
8. MID SWEEP TONE CONTROLS (GAIN & FREQ.)
These two controls will take some time to learn how to use. First, the FREQ.
control does not function if the GAIN control is set in the center “0” position. To
demonstrate, turn the GAIN to the right for full boost. Now turn the FREQ. control from full left to full right and notice the added mids change frequencies as
15
17
16
19
12
9. COMPRESSOR (COMP)
For some people, a compressor is a new feature. What it basically does is reduce
(or compress) the volume of the incoming signal to conform to a preset maximum output level. This describes the COMP knob in the full-clock wise position where it functions as a limiter. As the knob is turned back (counter
clockwise) the compressor lets a larger and larger percentage of the incoming
signals to pass through. This is raising the threshold of where the compressor
turns on. The maximum compression ratio is 3:1.
EQ IN switch: when the blue LED is lit the Graphic EQ is in and will effect the
sound of the amplifier. The Graphic EQ can also be switched in and out with an
FS22 footswitch.
17. SPEAKER OUTPUT JACK(S)
There are 2 speaker output jacks designed for a total minimum impedance of 4
ohms.
18. AC POWER
The detachable AC POWER CORD supplied is designed to operate with one type
of voltage (the European 230V export model uses a CEE-7 plug cord set). Check
the rear power cord label for the proper voltage. Plug the cord into a grounded
“3” prong” power source. No attempt should ever be made to defeat or use the
amp without the ground connected.
19. HF DRIVER LEVEL CONTROL (ENCLOSURE)
11. MASTER VOLUME
The advantages of a compressor is to increase the overall level of playing (or
the average level) and not have peaks or other sudden loud parts (transients).
For example, in slap bass playing, the plucked notes can put out peaks that could
distort the amplifier at normal playing volumes. On the other hand, if the amplifiers volume was adjusted for these peaks, the rest of the notes would be too
quiet to hear. Now, when the compressor is adjusted to where the indicator LED
comes on when the peaks are present, the amplifier can be played louder and
still reduce the peaks without distortion. It’s like having someone constantly and
instantly re-adjusting the volume of the amplifier to prevent distortion when the
peaks occur.
The master is the last volume control of the amplifier. This is where overall level
of the amplifier is set. The master volume also effects the headphone output.
12. DI LEVEL & DI XLR OUTPUT
The BR series provides this professional feature only found on our larger bass
amplifiers. The direct output is used to send a direct signal to the main PA system
or a recording track. The signal is a buffered and balance version of the signal
straight from the input jack. Use the DI level control to adjust the output level
of the direct output, and use the Ground lift switch to break a ground loop buzz
caused by creating power ground loops through making the direct output connection to the PA system.
The Compressor circuit is also internally connected to the power amplifier. When
the amplifier reaches a distortion level that maybe harmful to speakers it activates the compressor to reduce the input signal. This in turn takes the amplifier
out of distortion and protects the speakers even when the compressor control
is set to “0”.
13. POWER SWITCH
The power switch turns on the amplifier and is indicated by the large blue jewel
light over the input jack.
10. 5-BAND POST SHAPE EQUALIZER AND EQ IN SWITCH
5 band’s of the GRAPHIC EQ have been custom shaped and selected for the
bass guitar. The levels and tonal shaping of each band are customized individually unlike a standard graphic EQ to increase its usefulness and sweeten the sound
of each band. Here are some references for the individual sliders to help relate
the frequencies in hertz to perceived sounds.
14. HEADPHONE/LINE OUT JACK
The 1/4” jack can be used for mono headphone or a line output to feed a mixer
or power amp.
15. SEND JACK (EFFECTS LOOP)
The SEND jack is the output of the preamp. This jack, used in conjunction with
the RETURN jack, makes up the external effects loop. The SEND jack is
designed to put out the proper level for the input of an external effects processor.
• The 80Hz slider is for the ultra lows. Often used in the cut region to boost or
reduce the low end.
• The 250 Hz slider is for the mid-low bass. The bass has a great deal of sound
here, so this slider can change the sound drastically. Slide it up and down to
hear what you like.
16. RETURN JACK (EFFECTS LOOP)
• The 500Hz slider is for the mid-bass frequencies. Like the 250Hz slider, there
is a great deal of bass guitar here also.
The RETURN jack completes the effects loop in conjunction with the SEND jack.
This jack is designed to receive signals from an external effects processor. When
something is plugged into this jack it goes directly into the power amp portion
of the bass amplifier and breaks the connection between the bass preamp and
the internal power amp.
• The 800Hz slider is for the bass guitar’s high mids. This is where the mids start
to get snappy, but they can also get honky.
• The 2KHz slider is for the bass guitar’s highs. The crispy high’s in slap bass
playing start in the range of this slider.
https://manual-hub.com/
In the back of the BR12 and BR15 there is a small jack plate with a level knob
for the HF Driver. This level control adjusts the volume of the HF Driver and
does not effect the 15” woofer.
The HF Driver level control is another way to increase or decrease the highs
coming from your bass. If more highs are desired, the HF Driver level can be
turned up (clock wise), or turned off if a warmer sound is desired.
Note: One thing to consider with the HF Driver volume is the direction the cabinet is facing. Because the combo amplifier’s HF Driver is less than two feet
off the ground, the listeners seated in front of the amplifier may be getting more
of the HF Driver volume than you (the player) standing in front of the amplifier.
So be conscious of the volume and direction of the HF Driver when adjusting.
">
