Pure power tolls 10.8V Li-ION Specifications

10.8V Li-ION
Charger
Original
Instructions
Read instructions before operating this tool.
H10100
PURE 10.8V Battery Charger
EC - DECLARATION OF CONFORMITY
TABLE OF CONTENTS
We, the importer
Evolution Power Tools Ltd.
Venture One
Longacre Close
Sheffield
S20 3FR
EC - Declaration of Conformity
Important Information
12 Month Limited Warranty
02
General Safety Rules
Additional Specific Safety Rules
04
Labels and Symbols
06
Charger Overview
07
Specification
07
Operation
08
Maintenance
09
Environmental Protection
09
Service Parts Lists
09
03
03
05
Declare that the product
Part numbers: PURECHARGER2(m9802)
Evolution: Pure
10.8V Batery Charger
Complies with the essential requirements
of the following European Directives:
2006/42/EC – Machine Directive
2006/95/EC – Low Voltage Directive
2004/108/EC – EMC Directive
2002/95/EC – Restriction of the use of
Certain Hazardous Substances in Electrical
and Electric Equipment
Standards and Technical specifications
referred to:EN 60335-1+ A13 : 2008
EN 60335-2-29: 2004
EN 50366:
EN 55014-1: 2006
EN 55014-2: 2008
EN 61000-3-2:2006
EN 61000-3-3: 2008
All documentation is held on file at the
above address and is available, on request
for review.
Authorized Signatory
Date: 29/1/2010
Name: Mr Matthew J Gavins
Position: Managing Director
Year of Manufacture: 2010
2
10.8V Li-ION
Charger
IMPORTANT
Please read these operating and safety
instructions carefully and completely. For
your own safety, before using this equipment
check that the voltage is correct and that all
handles and parts are firmly secured. If you
are uncertain about any aspect of using this
equipment, please contact our Technical
Helpline.
Technical Helpline UK 0870 609 2297
Technical Helpline USA 1-866-EVO-TOOL
PURE 10.8V Battery Charger
Congratulations on your purchase of
an Evolution Power Tools Pure 10.8V
Battery Charger. Please complete your
product registration on line to validate your
machine’s warranty period and ensure
prompt service if needed. We sincerely
thank you for selecting a product from
Evolution Power Tools.
12
MONTH
LIMITED
WARRANTY.
Evolution power tools reserves the right to
make improvements and modifications to
design without prior notice.
Evolution Power Tools will, within twelve (12)
months from the original date of purchase,
repair or replace any goods found to be
defective in materials or workmanship. This
warranty is void if the tool being returned has
been used beyond the recommendations
in the Instruction Manual or has been
damaged by accident, neglect, or improper
service. This warranty does not apply to
machines and / or components which
have been altered, changed, or modified
in any way, or subjected to use beyond
recommended capacities and specifications.
Electrical components are subject to
respective manufacturers’ warranties. All
goods returned defective shall be returned
prepaid freight to Evolution Power Tools.
Evolution Power Tools reserves the right
to optionally repair or replace it with the
same or equivalent item. In no event shall
Evolution Power Tools be liable for loss or
damage resulting directly or indirectly from
the use of our merchandise or from any
other cause. Evolution Power Tools is not
liable for any costs incurred on such goods
or consequential damages. No officer,
employee or agent of Evolution Power Tools
is authorized to make oral representations
of fitness or to waive any of the foregoing
terms of sale and none shall be binding on
Evolution Power Tools. Questions relating
to this limited warranty should be directed
to the company’s head office, or call the
appropriate Helpline number.
GENERAL SAFETY RULES
WARNING
When using electric tools, basic safety
precautions should always be followed to
reduce the risk of fire, electric shock and
personal injury.
Please read all of these instructions before
attempting to operate this machine. Save
this manual for future reference.
1. Keep work area clear. Cluttered work
areas invite accidents.
2. Consider work area environment. Do
not expose tools to rain. Do not use tools in
damp or wet locations. Keep work area well
lit. Never use tools near flammable liquids
or gases.
3. Protect yourself against electric shock.
Avoid body contact with earthed or grounded
surfaces.
4. Keep other people away. Do not let others,
especially children, come close to the work,
and touch the tool or the extension lead.
Keep them away from the work area.
3
5. Store idle tools. When not in use, tools
should be stored in a dry locked-up place,
out of children’s reach.
6. Never force the tools. Your tools will be
more efficient and safer when used at the
rate for which they were intended.
7. Use the right tool. Do not force small tools
to do the job of a heavy duty tool. Do not use
tools for purposes not intended; for example
do not use circular saws to cut tree limbs
or logs.
8. Dress properly. Do not wear loose clothing
or jewellery which may get caught in moving
parts. Non-skid footwear is recommended
when working outdoors. If you have long
hair, tie it back and wear protective hair
covering.
9. Use protective equipment. Use safety
glasses. Use face or dust mask if cutting
operations create dust.
10. Connect dust extraction equipment. If
the machines have a connection for dust
extraction equipment, ensure these are
connected and properly used.
11. Do not damage the cable. Never pull
the power cable to disconnect the machine.
Keep the cable away from heat, oil and
sharp edges.
12. Secure workpiece. Where possible,
use clamps or a vice to hold the workpiece.
It’s much safer than using your hands.
13. Don’t over reach. Keep proper footing
and balance at all times.
14. Maintain tools in good working condition.
Keep cutting tools sharp and clean for better
performance and optimum safety. Follow
instructions for lubricating and changing
accessories. Inspect power cables regularly
and, if damaged, have them replaced by an
authorised service centre. Inspect extension
cables regularly and replace immediately if
damaged. Keep handles dry, clean and free
from oil and grease at all times.
15. Disconnect tools. Disconnect tools from
the power supply when not in use, before
any maintenance operation and when
changing accessories such as blades, bits,
cutters, etc.
4
16. Remove adjusting keys and spanners.
Get into the habit of checking that adjusting
keys and spanners have been removed from
the machine before turning it on.
17. Avoid unintentional starting. Ensure
switch is in “off” position before plugging in
the machine.
18. Use proper extension leads. When the
tool is used outdoors, use only extension
leads intended for outdoor use and labelled
as such.
19. Stay alert. Concentrate on what you
are doing, use common sense and do not
operate the tool when you are tired.
20. Check that no part is damaged. Before
using a tool, make sure that it is in good
working order. Check the alignment and
condition of moving parts, mounting and any
other aspect that may affect its operation. A
guard or other part that is damaged should
be properly repaired or replaced by an
authorised service centre unless otherwise
indicated in this instruction manual. Do not
use the tool if the switch does not turn on
and off.
21. Warning. The use of any accessory or
attachment other than one recommended in
this instruction manual may present a risk of
personal injury.
22. Have your tool repaired at an authorised
service centre. This electric tool complies
with current safety rules. Repairs should
only be carried out by an authorised service
centre using original spare parts. Failing
this, the user could expose themselves to
considerable danger.
ADDITIONAL SAFETY RULES FOR YOUR
PURE BATTERY CHARGER
WARNING! READ AND UNDERSTAND ALL
OF THESE INSTRUCTIONS.
SAVE THESE INSTRUCTIONS FOR FUTURE
OPERATOR USE.
1. Do not use the charger outdoors or expose
to wet or damp conditions. Water entering
the charger will increase the risk of electric
shock.
10.8V Li-ION
Charger
2. Use this charger only with the designated
Pure rechargeable battery packs. Other
types of battery may overheat and burst
causing personal injury or damage.
3. Do not abuse the charger cord. Never
use the cord to carry the charger. Do not
pull the cord rather than the plug when
disconnecting from the power supply.
Replace damaged cords immediately.
4. Ensure that the power cord is routed so
that it does not pose a trip hazard. Also
ensure that it cannot come into contact with
sharp edges or moving parts which could
cause damage to the cord.
5. Do not use any attachment not
recommended or sold by the battery
charger manufacturer. Use of unauthorised
attachments or battery packs could lead to
a significant risk of electric shock, fire or
personal injury.
6. Keep the power cord and the charger
body from heat sources. Heat can damage
the charger body and/or internal parts.
7. Do not use this charger if the cord or plug
is damaged. A damaged cord or plug must
be replaced before the charger can be used.
8. Do not use the charger if it has been
dropped, received a sharp blow or in any
other way has been damaged. Have the
charger checked at an authorized service
centre.
9. Do not disassemble charger. Take to
an authorized service centre when service
or repair is required.
10. Unplug the charger from the mains power
supply when attempting maintenance or
cleaning. This will reduce the risk of electric
shock.
11. Disconnect the charger from the mains
supply when not in use. Store in a locked
cupboard out of children’s reach. Do not
store with any other small metallic items
that could fall into the charger battery-pack
port. Do not store in locations where the
temperature may reach or exceed 50 0C.
12. Do not touch any of the uninsulated
terminals in either the battery charger or
the battery pack. Terminals may be ‘live’
and there is a risk of electric shock.
WARNING
This machine is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning the safe use of the
machine by a person responsible for their
safety.
Children should be supervised to ensure
that they do not have access to, and are not
allowed to play with, this machine.
SAFETY LABELS & SYMBOLS
WARNING!
Do not operate machine if warning and / or
instruction labels are missing or damaged.
Contact Evolution Power Tools for replacement
labels.
Symbol
Description
V
Volts
A
Amperes
Hz
Hertz
~
Alternating Current
Double Insulated
Wear Safety
Goggles
5
Annotated photograph of 10.8V Battery charger
1
2
3
1. MAINS LEAD
2. BATTERY DOCKING PORT
3. LED CHARGING INDICATORS
4. VENTILATION SLOTS
6
4
10.8V Li-ION
Charger
SPECIFICATION
PURE 10.8V BATTERY CHARGER
Charger Input
Charger Output
Charging Time
240V ~ 50Hz
10.8 V DC
1 hour
OPERATING INSTRUCTIONS
WARNING
This charger is designed to charge Pure
10.8V battery packs. It should only be used
for this purpose. Using this charger with any
other battery packs could be dangerous.
CHARGING A BATTERY PACK
1. Position the charger on a work bench
or similar in a well ventilated location and
ensure that the charger cannot be covered
by workshop cloths etc.
RED LED
OFF
This charger is designed to detect problems
that can sometimes arise with rechargeable
battery packs. The status of the two LED’s
can alert the operator to potential problems.
Please refer to the table below.
CHARGER OR BATTERY PACK CONDITION
ON
Charger connected to power supply and ready to receive battery pack
ON
With battery pack inserted. Battery pack fully charged
FLASHING
ON
OFF
FLASHING
OFF
ON
CHARGING INDICATOR
GREEN LED
OFF
OFF
2. Plug the charger into a suitable power
socket. The green LED will illuminate.
3. Insert the Pure 10.8V battery pack into
the docking port of the charger. It will only fit
in one way round.
4. Firmly push the battery pack down into
the charger to ensure terminal connection.
The green LED will flash to confirm terminal
connection and that the charging cycle has
started.
5. When the green LED ceases flashing
but remains illuminated, the charging cycle
is completed and the battery pack is fully
charged.
6. Remove the battery pack from the charger,
and store the charger safely for future use.
OFF
Battery pack correctly inserted and charging cycle in progress
Battery temperature at or above 500C or below 00C
At least one of the three battery cells is lower than 2V
Battery failure or battery pack not properly connected to the charger
7
Note: If battery pack failure is suspected, we
recommend that the operator inserts a new
battery of known quality into the charger to
check that the charger is working correctly.
If the new battery charges correctly, then
the original battery is probably defective and
should be sent for safe recycling. If the new
battery pack displays the same problems as
the original, have the charger tested at an
authorized service centre.
Warning:
When a battery becomes discharged due
to prolonged use or exposure to direct
sunlight or heat, always allow the battery
pack to cool down before recharging. This
will allow the battery to be recharged to its
full capacity.
CHARGING TIMES
Normal charging time is approximately
1 hour but this can vary depending upon
circumstances.
a) If the battery pack is only partially
discharged it may take less than an hour to
recharge.
b) If the battery pack and ambient
temperature are very cold then recharging
could take up 1.5 hours.
c) If the battery pack is very hot it may not
recharge. Allow it to cool right down before
beginning the charging process.
MAINTENANCE
There are no user serviceable parts in this
charger.
Keep the charger clean and free from oil
and dirt etc. Clean with a dry cloth, and do
not use chemical cleaners which may affect
the plastic parts of the charger.
Regularly inspect the power cord and plug
or damage.
Ensure that the ventilation slots do not
become blocked.
8
ENVIRONMENTAL PROTECTION
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with
your Local Authority or retailer for recycling
advice.
10.8V Li-ION
Charger
Notes
9
Notes
10
10.8V Li-ION
Charger
Notes
11