McQuay | MAC | Specifications | McQuay MAC Specifications

Catalog
Air-Cooled Mini Chiller
Models: MAC 020-150 C/CR
M4AC 020-150 C/CR
M5AC 020-055CR
MAC-C-2009
Table of Contents
Nomenclature ......................................................................................................................1
- Product Line up
Features...............................................................................................................................5
Application Information........................................................................................................7
- Refrigerant Circuit Diagram
- Chiller Panel Controller
- Precautions and Installation
Sound Data .......................................................................................................................57
Selection Process .............................................................................................................64
- Water Pressure drop vs Flow rate
- Glycol
Engineering and Physical Data .........................................................................................67
- Specifications
Performance Data ...........................................................................................................118
Dimensional Data.............................................................................................................132
Electrical Data..................................................................................................................136
Wiring Diagrams..............................................................................................................145
Servicing and Maintenance..............................................................................................162
Troubleshooting...............................................................................................................163
Exploded View and Part List............................................................................................164
This manual supercedes MAC-C-2008
Note : Installation and maintenance are to be performed only by qualified personnel who are
familiar with local codes and regulations, and experienced with this type of equipment.
Caution : Sharp edges and coil surfaces are a potential injury hazard. Avoid contact with them.
Warning : Moving machinery and electrical power hazard. May cause severe personnel
injury or death. Disconnect and lock off power before servicing equipment.
“McQuay” is a registered trademark of McQuay International. All rights reserved.
© 2009 McQuay International. All rights reserved throughout the world.
Bulletin illustrations cover the general appearance of McQuay International products at the time of publication.
We reserve the right to change design and construction specifications at any time without notice.
Nomenclature
M
4
AC
080
Nominal
Cooling
Capacity
M R22 Equipment
4 R407C Equipment
Brand Name
(McQuay)
Air Cooled
Chiller
C
R
_ Cooling
R Heating
Generation
1
Product Line Up
MAC-C/CR
AXAB
x
x
x
x
x
x
x
x
AXAA
x
x
x
x
x
x
x
x
AXAB
x
x
x
x
x
x
x
x
AXAA
x
x
x
x
x
x
x
x
AXAB
x
x
x
x
x
x
x
x
FXAA
x
x
x
x
x
x
x
x
FXAB
x
x
x
x
x
x
x
x
FXAA
x
x
x
x
x
x
x
x
FXAB
x
x
x
x
x
x
x
x
FXAA
x
x
x
x
x
x
x
x
FXAB
x
x
x
x
x
x
x
x
FXAC
x
x
x
x
x
x
x
x
FXAD
x
x
x
x
x
x
x
x
FXAC
x
x
x
x
x
x
x
x
FXAD
x
x
x
x
x
x
x
x
FXAC
x
x
x
x
x
x
x
x
FXAD
x
x
x
x
x
x
x
x
FXAC
x
x
x
x
x
x
x
x
FXAD
x
x
x
x
x
x
x
x
020CR
AXAA
x
x
x
x
025CR
AXAA
x
x
x
x
030CR
AXAA
x
x
x
x
040CR
FXAA
x
x
x
050CR
FXAA
x
x
060CR
FXAA
x
080CR
FXAC
100CR
x
Capillary Tube
x
Single phase fan motor
x
CCH (crank case heater)
Water tank + pump
x
Phase protector
Terminal block
x
Anti freeze & auto pump on
Rotary compressor
x
Gold fin
CE mark
x
Expansion tank
LCD Panel - Chiller Panel
x
Pump only
Magnetic contactor
x
020C
Scroll compressor
PCB - MC01
AXAA
Model name
Nomenclature
Classification
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
025C
x
030C
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
040C
050C
060C
x
x
080C
MAC
x
x
x
x
100C
x
x
x
x
120C
150C
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
FXAC
x
x
x
x
x
x
x
x
x
x
x
x
x
x
120CR
FXAC
x
x
x
x
x
x
x
x
x
x
x
x
x
x
150CR
FXAC
x
x
x
x
x
x
x
x
x
x
x
x
x
x
2
x
M4AC-C/CR
x
AXAA
x
x
x
x
x
x
AXAB
x
x
x
x
x
x
AXAA
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Single phase fan motor
x
x
TXV
x
x
Capillary Tube
x
CCH (crank case heater)
x
x
Phase protector
x
Anti freeze & auto pump on
AXAB
x
Pump only
x
Expansion tank
x
Water tank + pump
x
Gold fin
x
Terminal block
CE mark
x
Isolator switch
LCD Panel - Chiller Panel
x
Rotary compressor
Magnetic contactor
AXAA
Scroll compressor
PCB - MC01
020C
Nomenclature
Model name
Classification
025C
x
030C
AXAB
x
x
x
x
x
x
FXAA
x
x
x
x
x
x
FXAB
x
x
x
x
x
x
FXAA
x
x
x
x
x
x
FXAB
x
x
x
x
x
x
FXAA
x
x
x
x
x
x
FXAB
x
x
x
x
x
x
080C
FXAG
x
x
x
x
x
x
x
x
100C
FXAG
x
x
x
x
x
x
x
120C
FXAG
x
x
x
x
x
x
150C
FXAG
x
x
x
x
x
x
020CR
AXAA
x
x
x
x
025CR
AXAA
x
x
x
x
030CR
AXAA
x
x
x
040CR
FXAA
x
x
050CR
FXAA
x
060CR
FXAA
080CR
040C
050C
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
060C
M4AC
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
FXAD
x
x
x
x
x
x
x
x
x
x
x
x
x
x
100CR
FXAD
x
x
x
x
x
x
x
x
x
x
x
x
x
x
120CR
FXAD
x
x
x
x
x
x
x
x
x
x
x
x
x
x
150CR
FXAD
x
x
x
x
x
x
x
x
x
x
x
x
x
x
3
x
LCD Panel - Chiller Panel
CE mark
Rotary compressor
Terminal block
Gold fin
Water tank + pump
Expansion tank
AXAA
x
x
x
x
x
x
x
x
x
025CR
030CR
AXAA
x
x
x
x
x
x
x
x
x
EXAA
x
x
x
x
x
x
x
x
040CR
EXAA
x
x
x
x
x
x
x
050CR
EXAA
x
x
x
x
x
x
055CR
EXAA
x
x
x
x
x
x
4
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
TXV
Pump only
Capillary Tube
Magnetic contactor
020CR
Anti freeze & auto pump on
PCB - MC01
M5AC
Nomenclature
Model name
M5AC-CR
Classification
Features
Refrigerant Circuit
Models MAC/M4AC080~150C/CR has been designed with two separate refrigerant circuits, i.e. it has two
compressors. By doing so, the unit has part loading capabilities, i.e. 0-50-100% of rated capacity. This will
improve the reliability and energy efficiency of the unit, especially during low loading operations. Each circuit is
factory brazed and evacuated before accurately charged with refrigerant to ensure optimum performance.
Because each circuit is separated, there is no danger of cross-contamination should either one of the compressor
experiences a burnt-up. Each circuit is also equipped with a carefully sized thermostatic expansion valve (for
cooling only units) to give optimum performance characteristic. For the heatpump version, the expansion process
is done with capillary tubes.
Scroll Compressor
Scroll Compressors are used (for model which is available) for the units (MAC/M4AC020C/CR using rotary
compressor) to give quiet and reliable performance over a wide operating temperature range. However, in
order to protect the compressors from damage, a phase protector (for model which is available) is provided to
prevent the compressors from rotating in the wrong directions.
Tandem Compressor
M5AC models are using R410A rotary compressors in tandem configuration. Tandem compressors are highly
efficient and cost saving. It reduces mechanical losses, minimize gas flow losses and turbulence. There are 3
steps capacity loading (0-40-60-100%) for M5AC040/050CR and 2 steps capacity loading (0-50-100%) for
M5AC030/055CR.
Condenser Fan Motor
Models MAC/M4AC080~150C/CR is equipped with two high air flow propeller fan blades which are made of
metal. The fans are driven vertically by weather proof motors which are single phase type.
Evaporator
The heat exchanger is made of stainless steel plates closely arranged and brazed together (BPHE) to ensure
high heat exchange efficiency. For models MAC/M4AC080~150C/CR, the water flow through the BPHE in a
channel on its own, while because of the two compressors, the refrigerant flows through another two separate
channels. The refrigeran t will either be in a counter-flow or parallel-flow with respect to the water, depending on
the mode of operation (cooling or heating).
Safety Procetection
The safety protections provided for the mini chiller are:
a) High and low pressure switches
b) Differential water flow switch
c) Compressor, water pump and fan motor overload protectors
d) Anti-freeze protection sensor
During abnormal condition, chiller panel controller will turn off the unit and then display the faults of operation.
Water Tank And Piping Connection
The models M4AC/MAC080~150C/CR does not come with a water buffer tank. However, the unit does come
with an 8 liters expansion tank. Besides that, an optional 135L hydraulic tank is also available.
The external water piping connection can be made either from the left or right side of the unit. Connection is
done with Ø1-1/4 “ female thread couplings for both supply and return pipes.
Meanwhile, MAC/M4AC020~060C/CR does come with a 22 L or 40 L (refer to specification) water buffer tank.
5
Antifreeze Protection
The chiller unit has several anti-freeze protection features:
1. Brazed plate heat exchanger anti-freeze
The BPHE has a strip heater around it to prevent water freezing inside
2. Auto mode
The chiller controller will force on the unit to the heat mode if the outdoor ambient air temperature
becomes too cold.
Maintenance
In order to facilitate of the controller, a rocker switch is provided to power-off the supply to the PCB. However,
switching off the switch will not disconnect the main incoming power supply to the chiller unit.
6
Application Information
Refrigerant Circuit Diagram
M4AC / MAC 020C / 025C / 030C
Water / Refrigerant Circuit Diagram
FILTER
IL
ILTER
DRIER
CAP TUBE
BPHE
WATER
A
ATER
OUT
AUTO PRESS RELIEF VA
V LV
L E
WATER
A
ATER
IN
COMPRESSOR
WATER
ATER PUMP
A
P
EXPANSION
P
PANSION
T
TANK
WATER
ATER STORAGE
A
T
TANK
PART NO : 70-03-4-06746
M4AC / MAC 040C / 050C / 060C
Water / Refrigerant Circuit Diagram
FILTER
IL
ILTER
DRIER
CAP TUBE
BPHE
WATER
A
ATER
OUT
EXPANSION
P
PANSION
T
TANK
AUTO PRESS RELIEF VA
V LV
L E
WATER
A
ATER
IN
COMPRESSOR
WATER
ATER PUMP
A
P
WATER
ATER STORAGE
A
T
TANK
PART NO : 70-03-4-0
87461
7
M4AC / MAC 020CR / 025CR / 030CR
Water / Refrigerant Circuit Diagram
CHECK
VALV
L E
LV
FILTER
IL
ILTER
DRIER
CHECK
VALV
L E
LV
COOLING
CAP
TUBE
HEATING
A
ATING
CAP
TUBE
BPHE
WATER
A
ATER
OUT
CHARGE
COMPENSAT
A OR
AT
AUTO PRESS RELIEF VA
V LV
L E
COMPRESSOR
WATER
A
ATER
IN
SUCTION
ACCUMULAT
A OR
AT
P
EXPANSION
T
TANK
WATER
ATER STORAGE
A
T
TANK
PART NO : 70-03-4-06745
M4AC / MAC 040CR / 050CR / 060CR
Water / Refrigerant Circuit Diagram
CHECK
VA VE
FILTER
IL
ILTER
DRIER
CHECK
VALV
L E
LV
BPHE
HEATING
A
ATING
CAP
TUBE
WATER
A
ATER
OUT
COOLING
CAP
TUBE
LIQUID
RECEIVER
EXPANSION
P
PANSION
T
TANK
AUTO PRESS RELIEF VA
V LV
L E
SUCTION
ACCUMULAT
A OR
AT
WATER
A
ATER
IN
COMPRESSOR
WATER
ATER PUMP
A
P
WATER
ATER STORAGE
A
T
TANK
PART NO : 70-03-4-06745
9
8
M4AC / MAC 080C / 100C / 120C / 150C
Water / Refrigerant Circuit Diagram
FIN TUBE
HEA T EXCHANGER
(SYSTEM 1)
FIN TUBE
HEA T EXCHANGER
(SYSTEM 1)
FIL TER DRIER
FIL TER DRIER
THERMOST ATIC
EXP ANSION
VA LV E
COMPRESSOR
THERMOST AT IC
EXP ANSION
VA LV E
COMPRESSOR
BRAZED PLA TE
HEA T EXCHANGER
WATER
OUTLET
WATER
INLET
M4AC / MAC 080CR / 100CR / 120CR / 150CR
Water / Refrigerant Circuit Diagram
FIN TUBE
HEA T EXCHANGER
(SYSTEM 2)
FIN TUBE
HEA T EXCHANGER
(SYSTEM 1)
4-W AY V ALV E
CHECK
VA LV E
HEA TING
CAP
TUBE
HEA TING
CAP
TUBE
FIL TER
DRIER
CHECK
VA LV E
COOLING
CAP
TUBE
CHECK
VA LV E
4-W AY V ALV E
FIL TER
DRIER
COOLING
CAP
TUBE
CHECK
VA LV E
COMPRESSOR
COMPRESSOR
SUCTION
ACCUMULA TOR
SUCTION
ACCUMULA TOR
LIQUID
RECEIVER
LIQUID
RECEIVER
WATER
IN
WATER
OUT
9
PAR T NO : 70-03-4-056764
M5AC 020CR / 025CR
Water / Refrigerant Circuit Diagram
CHECK
VALV
L E
LV
CHECK
VALV
L E
LV
FILTER
IL
ILTER
DRIER
COOLING
CAP
TUBE
HEATING
A
ATING
CAP
TUBE
BPHE
WATER
A
ATER
OUT
CHARGE
COMPENSAT
A OR
AT
AUTO AIR VENT
SUCTION
ACCUMULAT
A OR
AT
COMPRESSOR
WATER
A
ATER
IN
P
EXPANSION
P
PANSION
T
TANK
WATER
ATER PUMP
A
WA
WA
ATER
TER STORAGE
T
TANK
PART NO : 70-03-4-08054
WATER / REFRIGERANT
M5AC 030CR
Water / Refrigerant Circuit Diagram
4WV
BPHE
TWIN T UBE
JOINT
WATER O UT
WA
FILTER
L
DRIER
EXPANSION
P
TANK
CHECKK
VALVE
OI L
RETURN
T UBE
OI L
RETURN
TUBE
CHARGE
COMPENSAT
A OR
WATER IN
WA
PUMP
COMPRESSOR 2
COMPRESSOR 1
TXV
10
M5AC 040 / 050CR
Water / Refrigerant Circuit Diagram
W
4WV
BPHE
TWIN TUBE
JOINT
ACCUMULAT
A OR
FILTER
L
DRIER
CHECKK
VALVE
O IL
RETURN
TUBE
WA
W
ATER
O UT
EXPANSION
P
TTANK
OIL
RETURN
TUBE
WA
W
ATER
IN
PUMP
COMPRESSOR 1
COMPRESSOR 2
TXV
LIQUID RECEIVER
M5AC 055CR
Water
/
Refrigerant
Circuit Diagram
WATER / REFRI
4WV
BPHE
SUB ACCUMULAT
A OR
TWIN TUBE
JOINT
WA
W
ATER
OUT
FILTER
L
DRIER
OIL
RETURN
TUBE
CHECKK
VALVE
EXPANSION
P
T
TANK
OIL
RETURN
TUBE
WATER
WA
IN
PUMP
COMPRESSOR 2
COMPRESSOR 1
TXV
LIQUID RECEIVER
11
Chiller Panel Controller
1. Safety Consideration
Only specially trained and technicians and installers are authorized to install and service this
equipment..
1.1 General Installation Recommendations
• Only supply DC voltage (9-17V, typically 12V, maximum current 200mA) as a power source
to the device.
• Input contact voltage supply should limit to 12VDC or 24VAC.
• Isolated all the low voltage wiring (communication bus, etc) from high voltage power supply
wiring.
2. General Description
2.1 General
The chiller panel controller is designed to control the chiller operation. This device allows the
user to have customized control for each connected unit.
2.2 Features
The requirements of user friendly and easy to use have been taken into account in designing
this chiller panel controller. It can do the task as follow:
• Whole system configuration
• Unique parameter settings
• Operation status display
• Tracing fault record (easy in hardware troubleshooting)
The display is shown in an 8-lines graphical LCD display. There are 8 dedicated keys available
in the panel,
• Menu selection
• Navigation on the screen
• Modification of the selected value
During first start-up, the panel will have a default configuration (timer schedule, set point,
miscellaneous settings, etc) User can do the changes on that particular configuration later.
2.3 Panel Position
The chiller panel controller can be installed anywhere, as long as it is easy to accessed by
authorized personnel.
The requirements of installation are:
• Avoid exposure to shocks
• Avoid any source of electromagnetic pollution
• Avoid installation on uneven vertical surface
2.4 Operation Environmental Condition
• Temperature:
-10°C to 65°C operating temperature
-20°C to 85°C storage temperature
•
Relative Humidity:
0 to 95% non-condensing
12
3. Hardware Description
Legend
1&2
3
4
5
6
7
8
9
10
Navigation key
Execute instruction key
Cancel instruction key
Switching to heat mode shortcut key
Switching to cool mode shortcut key
Toggle ON/OFF shortcut key
Show alarm key
Graphical LCD display
ON/OFF indicator
Legend
1&2
3
4
5
6
7
8
9
10
Chiller terminal unit connection
Not available
CMOS rset jumper (JH2)
Chiller bus resist or configuration (JH3)
Not available
Not available
Not available
Not available
Backup battery
3.1 Key Explanation
The 2 navigation keys permit item selection and modifying the selected value.
ENTER key is used to execute the navigation instruction
ESC key is used to cancel the navigation instruction
Shortcut key to switch the operation mode in the summary pages
Shortcut key to trigger ON/OFF in the summary pages
Shortcut key to show fault / alarm in the summary pages
13
4. Installation
4.1 Chiller Bus
Supported up to 50 units of Chiller
Chiller 0
Chiller Panel 0
(Master)
Chiller 1
Chiller 2
5 way wire (CM8)
Chiller
Communication bus
Chiller Panel 1
(Slave)
Chiller Network
Chiller panel needs to be energized with +12Vdc. The 5 way wires that provided is once on the easiest
solution to establish a communication between the panel and chiller main board (CN8-CN8). If the 5-way
wires socket has been occupied in main board, just using 2 insulation wired are needed to establish a communication between panel and chiller main board.
Chiller panel can support maximum up to 50 units of chiller. In the chiller network, duplication of main board
unit address is not allowed. Each chiller main board should have their unique unit address (0-50).
For first time running, user need to assign a unique unit address to each main board in the chiller network.
User should follow the procedure below:
•
•
Only power ON one main board at once time. Make sure not others main boards are energize.
By using the panel connected to the main board.
<ENTER>
Sum m ary Pages
<ENTER>
Main Menu
Setting Menu
<ENTER>
G7 Unit No
1. General
Set Paraam eter
<ENTER>
<ENTER>
key in "0001" as passw ord
•
•
Key in unique unit address and press ENTER to execute.
De-energized the main board and repeat the procedures again all the main boards have been
assigned a unique unit address.
IMPORTANT : Do not assign a same unit address to more than one chiller main board.
RECOMMENDATION : Please select a coherant model (G1 Model) to all the chiller main boards in
the same network.
14
4.2 Others Configuration
•
•
•
JH2 in chiller panel should let it open (put the jumper header on one pin only) all the time
unless user need to do CMOS reset to that particular panel.
JH3 should let it open (put the jumper header on one pin only) all the time as well.
Remember to put in the coin cell battery on the panel. Without the backup battery, the panel will
always reset the time to 12:00am, 1st Jan 2000.
4.3 Installation of the Chiller Panel Controller
•
•
•
•
•
•
•
Disconnect the unit and ensure no others unit energy source that supplies the panel.
Open the rear panel of the Chiller Panel (insert a ‘flat-head’ screwdriver in the top joint of main
casing with rear panel to open the real panel).
Pass the necessary wires of the panel across the large opening in the rear panel. Place the rear
panel flat support against the wall and make marks on the wall through the four installation holes
(inner and outer).
Drill four appropriate holes in the marked places.
Attach the rear panel to the wall and put on the screws on it. Ensure that all cables are passed
through the hole of the rear panel.
Connect the wires to the corresponding terminal according to the wiring bus network. The
power supply and communication wires must be correctly connected to ensure that the
panel works.
Close the chiller panel (ensure the bottom joint is aligned for the casing, then complete others joint
part. Ensure that the contacts at the back of the panel are aligned with each others).
Bus Wiring Diagram
15
5. Software Description
5.1 Introduction
The Chiller Panel Controller can be used to control / display the status of Chiller.
Status viewing:
• ON/OFF status
• Mode (Cooling / Heating/ Boiling)
• Mode set temperature
• Compressor status (ON/OFF/ DEFROST)
• Water in, Water Out, Outdoor air and Panel temperature
• Chiller model (Chiller, Heat Pump, Chiller/ Boiler, Chiller+Boiler, Heat Pump/Boiler, Heat Pump+
Boiler
• Advance parameter settings
• Defrost sensor temperatures
• Compressor discharge sensor temperatures
• Compressor run times
• Incoming alarm/ fault/ error
Status settings:
• ON/OFF switching
• Mode setting (Cooling / Heating/ Boiling)
• Mode set temperature
• Manual entering defrost
• Advance parameter settings
• Password changing
• Panel option setting (Backlight, Alarm Buzzer, Screen saver, Contrast, Brightness, temperature
unit)
• Time and date settings
• Clearing compressor run time
16
5.2 Menu Structures
Menu Structure Diagram for Chiller
17
5.3 Chiller Menu Structure
5.31 Summary Pages
There are 4 pages in [Summary Pages]. Press UP or DOWN for page scrolling. Press ENTER to go to
[Main Menu]. Time and date are shown on top of each page. Beside that, the bottom of each page shows
current control unit of the Chiller.
For example:
[00] - Chiller Panel controls Chiller ID 0 currently
[03] - Chiller Panel controls Chiller ID 3 currently
[All] - Chiller Panel controls all Chiller currently
1st page: Display ON/OFF status, Mode settings and Temperature settings.
01/01/2000
12:00am
Status
: ON
Mode
: Cooling
Cool Temp
: 12.0°C
[00]
2nd page: Display Compressor status.
01/01/2000
Compressor
12:00am
: ON
[00]
3rd page: Display Water In, Water Out, Outdoor air and Panel temperature
01/01/2000
Water In
Water Out
Outdoor Air
Panel
12:00am
:19.8°C
: 25.6°C
: 32.2°C
: 20.5°C
[00]
4th page: DisplayChiller model, Compressor No. and Chiller ID.
01/01/2000
12:00am
Model
: Chiller
No. Comp
: 1 Comp
Unit No
:0
18
5.3.2 Main Menu
Press ENTER in [Summary Pages] to go into this menu
MAIN MENU
Operating Menu
Setting Menu
Timer Menu
Alarm Menu
Display Menu
There are 5 sub menus in [Main Menu]. Press UP or DOWN to select sub menus, ENTER to enter into
the sub menu or press ESC to exit to [Summary Pages]
5.3.2.1 Operation Menu
Select [Operation Menu] in [Main Menu] and press ENTER to go into this menu.
OPERATION MENU
Status
: ON
Mode
: Cooling
Cool Temperature : 12.0° C
Heat Temperature : 40.0° C
Some normal settings can be found here. Press UP or DOWN to select each settings, ENTER to start the
setting or press ESC here to exit to [Main Menu]
Settings : -ON/OFF unit
- Mode changing (Cooling/ Heating/ Boiling)
- Cooling temperature setting
- Manual Defrost Selection
5.3.2.1.1 Manual Defrost
Select [Manual Defrost] in [Operation Menu] and press ENTER to go into this menu.
Defrost Compressor
Comp 1
This menu lets user select one compressor to enter into defrost cycle manually, as long as the
environment fulfill the defrost requirement.
19
5.3.2.2 Settings Menu
Select [Settings Menu] in [Main Menu] and press ENTER to go into this menu.
SETTINGS MENU
Set Parameter
Change Passw ord
Panel Option
Set Panel ID
Some advance settings can be found here. Press UP or DOWN to select settings, ENTER to start the
setting or press ESC here to exit to [Main Menu].
Settings
- Set Parameter
- Password Changing
- Panel Option
- Set Panel ID
5.3.2.2.1 Set Parameter
Select [Set Parameter] in [Settings Menu] and press ENTER to go into this menu.
1.General
2. Sensor
3. Regulator
4. Compressor
5. Defrost
6. Antif reeze
7. Alarm and Contact
There are 7 groups of advance parameters for user to set in this menu, Press UP or DOWN to
select the group, ENTER to go into the group or ESC to exit to [Setting Menu].
Settings:- General
- Sensor
- Regulator
- Compressor
- Defrost
- Antifreeze
- Alarm and Contact
5.3.2.2.2 Password Changing
Select [Password Changing] in [Setting Menu] and Press ENTER to go into this menu.
Please enter the
Old passw ord ………..
0
- - --
User can change the old password in this menu.
Press ESC to exit to [Settings Menu].
20
5.3.2.2.3 Panel Option
Select [Panel Option] in [Setting Menu] and Press ENTER to go into this menu.
Backlight
Buzzer
Screen Saver
Timeout
Contrast
Brightness
Temp Unit
: Norm al :
: On
: Disable
: 5m
: 50%
: Medium
:°C
User can do some miscellaneous for the panel. These settings would not affect whole system performance.
Settings - Toggle Backlight
- Alarm Buzzer
- Enable / Disable Screen Saver
- Screen Saver timeout
- Contrast display
- Backlight brightness
- Temperature unit
Press ESC to exit to [Settings Menu]
5.3.2.2.4 Set Panel ID
Select [Set Panel ID] in [Settings Menu] and press ENTER to go into this menu.
Please enter the
Panel ID……
=> Unit 0
User can assign the ID no, to the panel.
Example: If ID no. 0 has been assigned, the panel acts like Master Panel Unit. It can choose to control
each Chiller in the network.
If other ID no. (1-50) has been assigned, the panel acts like Slave Panel Unit. It is dedicated to
one particular Chiller. It can only control the Chiller with same ID in the network.
Press [ESC] to exit to [Settings Menu]
21
5.3.2.3 Time Menu
Select [Time Menu] in [Main Menu] and press ENTER to go into this menu.
TIMER MENU
Clock Setting
Date Setting
Time Schedule
Timer : Disable
:
All the timer/ schedule settings are included in this menu. Press UP or DOWN to select each settings.
ENTER to start the setting or press ESC here to exit to [Main Menu].
Settings:
- Set Clock
- Set Date
- Set Schedule ( 7 days Programmable Timer)
- Enable/ Disable Timer Schedule
5.3.2.3.1 Set Clock
Select [Clock Setting] in [Timer Menu] and press ENTER to go into this menu.
Set Time :
hh: mm
00: 00
User can set the time in this menu. The time setting is in 24-hour format.
Pres [ESC] to exit to [Timer Menu].
22
5.3.2.3.2 Set Date
Select [Date Setting] in [Timer Menu] and press ENTER to go into this menu.
Set Time :
yyyy hh mm
2000 /01 / 01
User can set the date in this menu. The date is set according to sequence below:
(year) / (month) / (day)
Press [ESC] to exit to [Timer Menu].
5.3.2.3.3 Set Schedule
Select [Schedule Timer] in [Timer Menu] and press ENTER to go into this menu.
Sun
Mon
Tue
Wed
Timer 1
ON OFF
0800 1600
0800 1600
0800 1600
0800 1600
Timer2
ON OFF
____ ____
____ ____
____ ____
____ ____
This is the 7 days programmable timer schedule menu. There are 2 ON/OFF events in one day. User can
choose to set each day of week (Sunday - Saturday) ON/OFF timer. Before this schedule carry their
effect to the Chiller, user need to set the [Timer] in [Timer Menu] to enable.
Press [ESC] to exit to [Timer Menu].
5.3.2.4 Alarm Menu
Select [Alarm Menu] in [Main Menu] and press ENTER to go into this menu.
ALARAM MENU
Show Alarms
Erase All Alarm
This place keeps records for all previous occurred fault/ alarms. User can view the alarm history and clear
that record (alarm history) as well. The panel can keep up to 20 fault/ alarm records.
Press ESC to exit to [Main Menu]
23
5.3.2.4.1 Show Alarms
Select [Show Alarms] in [Alarm Menu] and press ENTER to go into this menu.
[Ch 0]
Alarm 1
Comp 1 overload
01/ 01/ 00
12:00am
User can view all the fault/ alarm records in this menu.
The record shows
- Alarm type
- Alarm occurred date
- Alarm occurred time
- Alarm occurred unit (Chiller ID)
Beside that, user can erase the alarm record in this menu.
Press [ESC] to exit to [Alarm Menu].
5.3.2.4.2 Erase All Alarms
Select [Erase All Alarms] in [Alarm Menu] and press ENTER to go into this menu.
Are you sure ?
Press Enter to erase,
or ESC to exit.
User can rase all the alarm / fault records at once in this menu.
Press [ESC] to exit to [Alarm Menu].
5.3.2.5 Dispaly Menu
Select [Display Menu] in [Main Menu] and press ENTER to go into this menu.
DISPLAY MENU
Defrost Sensor
Discharge Sensor
Comp Run Time
This menu display Defrost Sensor temperature, Compressor Discharge sensor temperature and
Compressor Run Time. Beside that, user can clear each Compressor Run Time for Chiller.
Press [ESC] to exit to [Main Menu]
24
5.3.2.5.1 Defrost Sensor
Select [Defrost Sensor] in [Display Menu] and press ENTER to go into this menu.
Defrost Sensor
Comp 1 : 12.8° C
User can view the defrost sensor temperature for each compressor in the Chiller.
Press [ESC] to exit to [Display Menu]
5.3.2.5.2 Discharge Sensor
Select [Discharge Sensor] in [Display Menu] and press ENTER to go into this menu.
Discharges Sensor
Comp 1 : 36.5° C
User can view the discharge sensor temperature for each compressor in the Chiller.
Press [ESC] to exit to [Display Menu].
5.3.2.5.3 Comp Run Time
Select [Comp Run Time] in [Display Menu] and press ENTER to go into this menu.
Comp Run Time
Comp 1 : 13579h
User can view the compressor run time for each compressor in the Chiller. Beside that, user can
clear each compressor run time in this menu. User needs to key in the correct password before
clearing the compressor run time.
Press [ESC] to exit to [Display Menu].
25
6. Operation User Manual
6.1 Starting
Chiller panel can be set as Master or Slave panel unit. When the Panel ID is set to ‘0’, it acts like a Master
panel, whereas it is Slave panel if Panel ID is set to others number (1-50).
Chiller panel can control the Chiller if both ID no. (Panel ID and Chiller ID) are same.
For example: Panel ID 1 can only control Chiller ID 1
Master Panel can choose to control each Chiller or control all Chiller at once in the network.
For example : Panel ID 0 (master) can control Chiller ID 0 / ID 1/ ID 32 .... or all Chillers at once.
Panel ID can be set in Set Panel ID in Settings Menu.
Please enter the
Panel ID ……
=> Unit 0
26
6.2 Chiller Operation Control
6.2.1 Starting
During power on for the Chiller Panel, it needs to take several times to collect information from the Chiller.
At this time, all the status will show “--”. Please ensure the particular Chiller exists in the network. When
the process is completed, user can start to control the Chiller using the panel.
01/ 01/ 2000
12:00am
01/ 01/ 2000
12:00am
Status
: --
Status
: ON
Mode
: --
Mode
: Cooling
Cool Temp
: --
Cool Temp
: 12° C
[00]
[00]
In gathering information process
Gathering information completed
6.2.2 Changing Display Unit
Chiller Panel (Master) can choose to choose to control / display each Chiller status. This can be done in
[Summary Pages] only.
01/ 01/ 2000
12:00am
Status
: ON
Mode
: Cooling
Cool Temp
: 12° C
In [Summary Pages], press and hold ENTER buttom
(1 second) to go into [Unit Selection] menu.
[00]
Unit Selection
:
Select All
Select One
:0
Unit Selection
:
Select All
Select One
Select “Select All” and press ENTER if user want to
control all Chilelr in the network, or select “Select One”
to control a particular Chiller. Press ESC to exit to
[Summary Pages].
Select a Chiller ID via UP or DOWN and press ENTER
to confirm or ESC to cancel.
:0
27
6.2.3 Switching ON/OFF
There are several ways to switch ON/OFF for the Chiller.
i) [Summary Pages]
Press and hold ON/OFF button (hold 1 second). Please note that the ON/OFF button will only function in
[Summary Pages].
ii) [Operation Menu]
<ENTER>
Summary Pages
<ENTER>
Main Menu
Operation Menu
<ESC>
OPERATION MENU
Status
: ON
Mode
: Cooling
Cool Temperature : 12.0° C
Heat Temperature : 40.0° C
OPERATION MENU
Status
: ON
Mode
: Cooling
Cool Temperature : 12.0° C
Heat Temperature : 40.0° C
<ESC>
In [Operation Menu], select “Status” and press
ENTER.
Toggle ON/OFF via UP or DOWN button, and then
press ENTER to confirm the change or ESC to cancel.
iii) [Timer Menu]
<ENTER>
Summary Pages
<ENTER>
Main Menu
Timer Menu
<ESC>
<ESC>
7 days programmable time can turn chiller ON/OFF. User can set the schedule in this
[Timer Menu]. Please refer 6.2.11 (page 27) for schedule settings.
28
6.2.4 Switching Mode
There are several ways to switch the mode for the Chiller. Please take note that some mode cannot be set
due to current Chiller model settings.
Chiller Model
Chiller
Heat Pump
Chiller / Boiler
Heat Pump /Boiler
Chiller + Boiler
Heat Pump + Boiler
Cooling
√
√
√
√
√
√
Mode
Heating
×
√
×
√
×
√
Boiling
×
×
√
√
Auto
Auto
√
×
Auto
- Allow to set
- Not Allow to set
- Turn ON automatically
i) [Summary Pages]
Cooling - Press and hold COOL button.
Heating - Press and hold HEAT button (if it allows to set).
Boiling - Press and hold HEAT button again (if it allows to set).
ii) [Operation Menu]
<ENTER>
Summary Pages
<ENTER>
Main Menu
<ESC>
OPERATION MENU
Status
: ON
Mode
: Cooling
Cool Temperature : 12.0° C
Heat Temperature : 40.0° C
OPERATION MENU
Status
: ON
Mode
: Cooling
Cool Temperature : 12.0° C
Heat Temperature : 40.0° C
Operation Menu
<ESC>
In [Operation Menu], select “Mode” and press
ENTER to start setting or ESC to exit to [Main Menu]
Toggle ON/OFF via UP or DOWN button, and then
press ENTER to confirm the change or ESC to
cancel.
29
6.2.5 Changing Mode Set Temperature
There are 2 ways to change the mode set temperature for the Chiller.
i) [Operation Menu]
OPERATION MENU
Status
: ON
Mode
: Cooling
Cool Temperature : 12.0°C
Heat Temperature : 40.0°C
OPERATION MENU
Status
: ON
Mode
: Cooling
Cool Temperature : 12.0°C
Heat Temperature : 40.0°C
In [Operation Menu], select “Cool Temp” / “Heat
Temp”and press ENTER start setting or ESC to exit
to [Main Menu].
Change value via UP or DOWN button, and then press
ENTER to confirm the change or ESC to cancel.
ii) [Set Parameter]
<ENTER>
Summary Pages
<ENTER>
Main Menu
<ESC>
Settings Menu
<ESC>
<ENTER>
<ESC>
Key in Password
Set Parameter
1.
2.
3.
4.
5.
6.
7.
General
Sensor
Regulator
Compressor
Defrost
Antifreeze
Alarm and Contact
R1 Cool SP
R2 Cool Diff
R3 Heat SP
R4 Heat Diff
R5 Min Cool SP
R6 Max Cool SP
R7 Min Heat SP
: 12.0° C
: 3.0° C
: 40.0° C
: 3.0° C
: -20° C
: 40° C
: -20° C
R1 Cool SP
R2 Cool Diff
R3 Heat SP
R4 Heat Diff
R5 Min Cool SP
R6 Max Cool SP
R7 Min Heat SP
: 12.0° C
: 3.0° C
: 40.0° C
: 3.0° C
: -20° C
: 40° C
: -20° C
In [Set Parameter], select “Regulator” and press
ENTER. Press ESC tp exit to [Main Menu].
Select “R3”/ “R5” and press ENTER to start setting
or ESC to exit to [Set Parameter] menu.
Change value via UP or DOWN button. The
boarderline is limited by R5&R6 (cool), R7&R8(heat).
Press ENTER to confirm or ESC to cancel.
30
6.2.6 Manual Defrost
User can choose which compressor will go into manual defrost cycle by using the Chiller Panel, as long
as the condition is fulfilled with defrost condition. This can be done in [Operation Menu].
<ENTER>
Summary Pages
<ENTER>
Main Menu
<ESC>
Operation Menu
<ESC>
Please take note that “Manual Defrost” option will only available in HEATING mode. It will disappear in
COOLING/ BOILING mode.
OPERATION MENU
Status
: ON
Mode
: Cooling
Cool Temperature : 12.0° C
Heat Temperature : 40.0° C
OPERATION MENU
Status
: ON
Mode
: Heating
Cool Temperature : 12.0° C
Heat Temperature : 40.0° C
“Manual Defrost” disappear when Chiller not in HEATING mode
OPERATION MENU
Status
: ON
Mode
: Heating
Cool Temperature : 12.0° C
Heat Temperature : 40.0° C
Manual Defrost
In [Operation Menu], select [Manual Defrost], press
ENTER to go into it, or ESC to exit to [Main Menu].
Defrost Compressor
Comp 1
Select which compressor to go into defrost cycle via
UP or DOWN button. Press ENTER to confirm or ESC
to exit to [Operation Menu].
31
6.2.7 Advance Parameter Settings
The Chiller Panel provide user a lot of advance parameter settings for the Chiller. The parameters are
divided into 7 groups. There all are stored in [Set Parameter] menu and it is password-procteted layer
in the panel.
* CAUTION : INPROPER SETTINGS WILL CAUSE PERMANENT DAMAGE TO THE CHILLER !!!
<ENTER>
Summary Pages
<ENTER>
Main Menu
Settings Menu
<ESC>
<ESC>
<ENTER>
Key in Password
Set Parameter
7 groups of Advance Parameter:
1) General
G1 Model
G2 No. Comp
G3 On/Off in
G4 Col/ Heat In
G5 Ext Alarm in
G6 Water Sys
G7 Unit No
: Chiller
: 1 Comp
: Disable
: Disable
: Disable
: Isolated
:0
2) Sensor
S1 Water Enter
S2 Water Leave
S3 Air Sensor
S4 Defrost 1
S5 Defrost 2
S6 Defrost 3
S7 Defrost 4
: 0.0° C
: 0.0° C
: 0.0° C
: 0.0° C
: 0.0° C
: 0.0° C
: 0.0° C
S8 Cp Dish 1
S9 Cp Dish 2
S10 Cp Dish 3
S11 Cp Dish 4
: 0.0° C
: 0.0° C
: 0.0° C
: 0.0° C
: 12.0° C
: 3.0° C
: 40.0° C
: 3.0° C
: -20° C
: 40° C
: -20° C
R8 Max Heat SP
R9 Ax Heat SP
R10 Ax Heat Diff
R11 Au Bo SP
R12 Au Bo Diff
R13 Au Bo Start
: 90° C
: 5.0° C
: 2.0° C
: 5.0° C
: 2.0° C
: 30m
3) Regulator
R1 Cool SP
R2 Cool Diff
R3 Heat SP
R4 Heat Diff
R5 Mix Cool SP
R6 Max Cool SP
R7 Min Heat SP
32
<ESC>
4) Compressor
C1 Min Run
C2 Min Stop
C3 2On Interval
C4 2Cp ON Dly
C5 P-Cp ON Dly
C6 Cp-P OFF Dly
C7 Cp Cut Off
: 12s
: 240s
: 360s
: 15s
: 60s
: 60s
: 120° C
5) Condenser Defrost
D1 Start Temp
D2 End Temp
D3 Max Dura
D4 Interval
D5 Dly Bfr Def
D6 Dly Aft Def
: -3° C
: 14° C
: 10m
: 45m
: 0s
: 0s
6) Cool Mode Antifreeze
A1 Heater SP
A2 Heater Diff
A3 Sensor
A4 Alarm SP
A5 Alarm Diff
: 5° C
: 2.0° C
: Leave
: 3° C
: 2.0° C
7) Alarm and Contact
P1 FS Confirm
P2 FS Delay
P3 LP Delay
P4 CO Reset
P5 HP Rest
P6 LP Reset
P7 FO Reset
: 5s
: 180s
: 30s
: Manual
: Auto
: Auto
: Manual
P8 RO Reset
P9 FS Reset
P10 Aux Reset
P11 A/F Reset
P12 CO Contact
P13 HP Contact
P14 LP Contact
Please refer to 8. APPENDIX for detail desciption.
33
: Manual
: Manual
: Manual
: Manual
: Normal
: Normal
: Normal
P15 FO Contact
P16 PO Contact
P17 FS Contact
P18 EA Contact
P19 DE Contact
: Normal
: Normal
: Normal
: Normal
: Normal
6.2.8 Changing Password
For security purpose, some places in the panel are password-proctected. User can change the password
at anytime.
<ENTER>
<ENTER>
Summary Pages
Main Menu
Settings Menu
<ESC>
<ESC>
<ENTER>
<ESC>
Change Password
Please enter the
Old password ----------0
----
User needs to enter the old password in order to change
the password.
Change the 1st digit value via UP or DOWN. Press
ENTER to start enter 2nd digit and the rest, or ESC to
exit at anytime.
Password accepted . . .
Password error . . .
Access granted !
Access denied !
If password not correct, this message will be
shown and exit to [settings Menu]
If password correct, this message will be
shown and proceed to new password
settings.
Please enter the
New password ----------0
----
Same as previous, UP DOWN to change value, ENTER
to go to next digit, ESC to exit.
User is not allowed to set the password to 0000.
New password
Has been set …….
New password
‘0 0 0 0’
Is not accepted ………
If new password is accepted, this message
will be shown and then exit to [Settings Menu].
If new password is ‘0000’, this message
will be shown and then exit to [Settings Menu].
The password remains as previous.
34
6.2.9 Clock Setting
User can set the clock for the panel.
<ENTER>
Summary Pages
<ENTER>
Main Menu
Timer Menu
<ESC>
<ESC>
<ENTER>
<ESC>
Set Time
Set Time :
UP or DOWN to change ‘hour’. ENTER to set ‘minute’
or ESC to exit to [Timer Menu].
hh mm
UP or DOWN to change ‘minute’. ENTER to confirm
or ESC to set ‘hour’again.
00 : 00
6.4.10 Date Setting
User can set the date for the panel.
<ENTER>
Summary Pages
<ENTER>
Main Menu
Timer Menu
<ESC>
<ESC>
<ENTER>
<ESC>
Set Time
Set Time :
yyyy hh mm
2000 /01 / 01
UP or DOWN to change ‘year’. ENTER to set ‘month’ or
ESC to exit to [Timer Menu].
UP or DOWN to change ‘month’. ENTER to set ‘day’ or
ESC to set ‘year’ again.
UP or DOWN to change ‘day’. ENTER to confirm or
ESC to set ‘month’ again.
35
6.2.11 7 days Programmable Setting
The are 2 ON/OFF events in one day for the schedule. This schedule is applicable to all the chillers in
the network.
Sun
Mon
Tue
Wed
Sun
Mon
Tue
Wed
Timer 1
ON OFF
Timer 2
ON OFF
0800 1600
0800 1600
0800 1600
0800 1600
____
____
____
____
Timer 1
ON OFF
Timer 2
ON OFF
UP or DOWN select event. ENTER to start
setting or ESC to back to select day of week.
0800 1600
0800 1600
0800 1600
0800 1600
____
____
____
____
Event setting is same like time setting. User can
disable the event by set it to ‘- - - -’
____
____
____
____
____
____
____
____
UP or DOWN select day of week, ENTER
to select event or ESC to exit to [Timer Menu].
Before the schedule will carry the effect, user need to set ENABLE for “TIMER” in [Timer Menu].
TIMER MENU
Set Time
Set Date
Set Schedule
Timer : Disable
Select “Timer” and press ENTER to start the
settings. UP or DOWN to toggle Enable/ Disable,
ENTER to confirm or ESC to cancel.
36
6.2.12 Viewing Alarm / Erase Alarm Record
Whenever a new fault/ alarm is occurred, there will be a message pop up to show the fault/ alarm.
Backlight will blinking with beeping sound (if “Alarm Buzzer” is set ON). If the fault/ alarm has not been
dissolved from the Chiller, a sign [A] will be shown in the [Summary Pages].(from pop up menu)
automatically if the fault/ alarms have been dissolved.
While the fault/ alarms have not been dissolved (sign [A]), user can check that fault/ alarm by to into
[Alarm Menu]. If all the fault/ alarm have been dissolved, user can view the fault/alarm historty records
in [Alarm Menu] as well. Screen saver will be deactivated while all the alarms have not been dissolved.
If panel ID is set 0 (Master panel), it can receive and view all the fault / alarms from all chillers in the
network.
[Ch 0]
New Alarm 1
Comp 1 overload
12:00am
01/ 01/ 2000
[Ch 0]
New Alarm 1
Comp 1 overload
01 / 01/ 00
[Ch 0] show alarm occurred unit.
Press any button to stop backlight blinking and beeping.
Press ESC again to exit to normal page.
Press UP or DOWN to scroll the record.
Press ENTER if user want to erase the reocrd, or ESC
to exit to [Alarm Menu].
12:00am
Erase Alarm ?
Press ENTER to erase the alarm, or ESC to cancel.
Please Enter to Erase,
Or ESC to exit
User can erase all the fault/ alarm record at once time through [Erase All Alarm] in [Alarm Menu].
37
6.2.13 Viewing Defrost Sensor Temperature
The Chiller Panel displays defrost sensor temperature for each compressor in [Defrost Sensor]
in [Display Menu].
Defrost Sensor
Press ESC to exit to [Display Menu]
Comp 1 : 12.8° C
6.2.14 Viewing Compressor Discharge Temperature
The Chiller Panel displays compressor discharge temperature for each compressor in [Discharge Sensor]
in [Display Menu].
Discharge Sensor
Comp 1
: 36.5° C
Press ESC to exit to [Display Menu]
38
6.2.15 Viewing/ Clear Compressor Run Time
User can view/ clear the compressor run time for the Chiller in [Comp Run Time] in [Display Menu].
Press UP or DOWN to select teh compressor. ENTER
to start clear the run time, or ESC to exit to [Display
Menu].
Comp Run Time
Comp 1 : 13579h
Clear Run Time ?
Press ENTER and key in the password to confirm or
ESC to cancel
Press Enter to Clear
Or ESC to exit.
6.2.16 Miscellaneous Settings
User can do some miscellaneous settings to the panel.
Backlight
Buzzer
Screen Saver
Timeout
Contrast
Brightness
Temp Unit
: Normal :
: On
: Disable
: 5m
: 50%
: Medium
:°C
Press UP or DOWN to select the item. ENTER to set,
or ESC to exit to [Settings Menu].
Press UP or DOWN to toggle the value. ENTER to confirm,
or ESC to cancel.
39
Parameter
Value
Description
Backlight
Normal
Always
ON
OFF
Enable
Disable
1-30m
0-100%
OFF
Low, Medium, High
°C
°F
Turn ON backlight for 30s via key press
Always ON backlight
Enable beeping sound when fault/ alarm occurred
Disable beeping sound when fault/ alarm occurred
Show screen saver when timeout
No screen save
Timeout for showing screen saver
Adjust the contrast setting for the LCD panel
No backlight
Adjust the backlight intensity
Display temperature in degree Celsius
Display temperature in degree Fahrenheit
Buzzer
*Screen Saver
*Timeout
Contrast
Brightness
Temp Unit
* This product must be branded. Screen saver will be deactivated for brand less panel
6.3 CMOS Reset
•
CMOS reset allows user to reset some settings to default value such as:
Password
Backlight
Buzzer
Screen Saver
Timeout
Contrast
Brightness
Temp Unit
•
-> 0001
-> Normal
-> ON
-> Disable
-> 5m
-> 50%
-> Medium
-> C
Procedures
1. Power OFF the panel
2. Close the jumper JH2 with the provided jumper header
3. Power ON the panel and the LCD panel should display as follow:
CMOS reset completed !
CMOS is resetting …………
Please remove JUMPER
and restart the panel
4. Remove the jumper header (put the jumper header on 1 pin only), power OFF and then
power ON the panel.
40
7. Problem And Troubleshooting
Symptoms
1 Panel gets hot
abnormally
2 The LCD no display
(blank screen)
3 - -' for all status
(quite a long time)
4 ON/ OFF, COOL or
HEAT button not
function
5 Cannot switch to
HEATING mode
6 Cannot switch to
BOILING mode
7 No "Manual Defrost"
item
8 Cannot step inside
[Set Parameter]
Possible Cause
- Wiring fault in 12VDC supply
Troubleshooting
- Change a new panel module and turn ON the unit again
after the verification
- Correct the wiring problem
- Check the wiring and supply 12VDC to panel
- Check the power source
- Change a new panel module
- Ensure the selected unit exits in the network
- Ensure the wiring is correct
- Ensure the wiring is not defective
-Ensure the wiring has been isolated from high power cable
- Select a coherent unit address on the panel (refer to
6.2.2)
- Change a new module
- Ensure it is pressed (hold 1s) in [Summary Pages]
not in other menu.
- Change a new module
- Ensure this mode is available in current "Model" of
Chiller, please refer to 6.2.4
- Ensure this mode is available in current "Model" of
Chiller, please refer to 6.2.4
- Ensure current running mode is HEATING
- Wiring fault in 12VDC supply
- No power supply
- Voltage supply too low
- Module defective
-Panel cannot/ not yet
received the information
from chiller or FCU completely
- That particular unit address
is not recognized by the panel
- Module defective
- Software limitation
- Module defective
- Software limitation
- Software limitation
- Software limitation
- Software limitation. Panel has
not received all the information
from chiller completely
9 7 Days Programmable - Software limitation. User
Timer not function
did not activate the schedule
10 No beeping sound
- Software limitation. User
when new alarm
did not set ON to the alarm
occurred
buzzer
11 No screen saver after - Software limitation. User did
timeout
not set ENABLE to the screen
saver
12 Time always reset to - No backup battery
12:00am, 1st Jan 2000 - Energy of the backup battery is
low
13 Panel stop operation. - Unstable power supply
Whole operation
- Energy of the backup battery is
freezing (hang)
low
- Refer to symptoms 3
Control of Chiller:
- Ensure the "Timer" in [Timer Menu] is set ENABLE
Control of Chiller:
- Ensure the 'Timer" in [Operation Menu] is set ENABLE
- Ensure "Buzzer" in [Panel Option] is set ON
- Ensure "Screen Saver" in [Panel Option] I set ENABLE
- Replace coin cell battery
- Power off the panel. Take out the backup battery as well.
Replace with a new 3V coil cell battery if necessary. Put
back the backup battery into the panel and power on again
41
8. Appendix
G7
General
Model
0=Chiller
1=Heat pum p,
2=Chiller/ Boiler,
3=Heat pum p/ Boiler, 4=Chiller+Boiler
5=Heat pum p+Boiller
Number of com pressor
1=1 com pressor,
2=2 com pressor,
3=3 com pressor,
4=4 com pressor
On/Off input
0=disable, 1=enable
Coo/ Heat input
0=disable, 1=enable
External alarm input
0=disable, 1=enable
Water system for chiller netw ork
0=independent, 1=m odular
Unit num ber
S1
S2
S3
S4
S5
S6
S7
S8
S9
S10
S11
SENSOR
Entering w ater sensor calibration
Leaving w ater sensor calibration
Air sensor calibration
Defrost(condenser) sensor 1 calibration
Defrost(condenser) sensor 2 calibration
Defrost(condenser) sensor 3 calibration
Defrost(condenser) sensor 4 calibration
Com pressor discharge sensor 1 calibration
Com pressor discharge sensor 2 calibration
Com pressor discharge sensor 3 calibration
Com pressor discharge sensor 4 calibration
Type
U
U
U
U
U
U
U
U
U
U
U
Unit
°C (F)
°C (F)
°C (F)
°C (F)
°C (F)
°C (F)
°C (F)
°C (F)
°C (F)
°C (F)
°C (F)
Default
0 (0)
0 (0)
0 (0)
0 (0)
0 (0)
0 (0)
0 (0)
0 (0)
0 (0)
0 (0)
0 (0)
Min
-12 (21.6)
-12 (21.6)
-12 (21.6)
-12 (21.6)
-12 (21.6)
-12 (21.6)
-12 (21.6)
-12 (21.6)
-12 (21.6)
-12 (21.6)
-12 (21.6)
Max
-12 (21.6)
-12 (21.6)
-12 (21.6)
-12 (21.6)
-12 (21.6)
-12 (21.6)
-12 (21.6)
-12 (21.6)
-12 (21.6)
-12 (21.6)
-12 (21.6)
Resolution
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
Type
D
U
D
U
U
U
U
U
U
Unit
°C (F)
°C (F)
°C (F)
°C (F)
°C (F)
°C (F)
°C (F)
°C (F)
°C (F)
Default
12 (53.6)
1.5* (2.7)
40 (104)
1.5* (2.7)
7 (44.6)
20 (68)
30 (68)
50 (122)
5 (9)
Min
R5
0.4 (0.7)
R7
0.4 (0.7)
-20 (-4)
R5
-20 (-4)
R7
0 (0)
Max
R6
10 (18)
R8
10 (18)
R6
40 (104)
R8
90 (194)
40 (72)
Resolution
0.1
0.1
0.1
0.1
1
1
1
1
0.1
U
U
°C (F)
°C (F)
2 (3.6)
5 (9)
0.4 (0.7)
0 (0)
10 (18)
40 (72)
0.1
0.1
R12
R13
REGULATOR
Cooling set-point
Cooling differential
Heating set-point
Heating differential
Minim um Cooling set-point
Maxim um Cooling set-point
Minim um Heating set-point
Maxim um Heating set-point
Auxiliary heater set-point(threshold below
below heating set-point)
Auxiliary heater differential
Auto boiler set-point(threshold below
Heating set-point)
Auto boiler differential
Auto boiler start tim e threshold
U
U
°C (F)
m in
2 (3.6)
30
0.4 (0.7)
0
10 (18)
199
0.1
1
C1
C2
C3
C4
C5
C6
C7
COMPRESSOR
Com pressor m inim um run tim e
Com pressor m inim um stop tim e
Tim e interval betw een tw o starts
Start delay betw een tw o com pressors
Pum p on ? com pressor on delay
Com p off ? pum p off delay
Discharge cut-off-set-point
Type
U
U
U
U
U
U
U
Unit
sec
sec
sec
sec
sec
sec
°C (F)
Default
120
180
450
15
180
60
120(248)
Max
0
0
0
0
0
0
0 (32)
Min
1990
1990
1990
199
1990
199
150 (302)
Resolution
10
10
10
1
10
10
1
D1
D2
D3
D4
D5
D6
CONDENSSOR
Start defrost tem perature
End defrost tem perature
Maxim um duration of defrost cycle
Defrost interval tim e
Delay before defrosting
Delay after defrosting
Type
U
U
U
U
U
U
Unit
°C (F)
°C (F)
m in
m in
sec
sec
Default
0 (32)
14 (57)
10
45
0
120
Max
-20 (-4)
D1
1
0
0
0
Min
D2
40 (104)
40
199
1990
1990
Resolution
1
1
1
1
10
10
G1
G2
G3
G4
G5
G6
R1
R2
R3
R4
R5
R6
R7
R8
R9
R10
R11
Type
F
Unit
Flag
Default
4
(Chiller+Boiler)
Min
0
Max
2
Resolution
1
F
Flag
1
1
4
1
F
Flag
0 (disable)
0
1
1
F
Flag
0 (disable)
0
1
1
F
Flag
0 (disable)
0
1
1
F
Flag
0 (disable)
0
1
1
F
Flag
0
0
50
1
42
A1
A2
A3
A4
A5
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
COOL MODE ANTIFREEZE
Antifreeze heater set-point
Antifreeze heater differential
Antifreeze sensor select
0=Leaving water, 1=Entering water
Antifreeze alarm set-point
Antifreeze alarm differential
Unit
°C (F)
°C (F)
Flag
ALARM AND CONTACT
Flow switch confirmation time
Flow switch alarm delay at pump start
Low pressure alarm delay at compressor start up
Comp overload alarm reset type
0=Manual reset, 1=Auto reset
High pressure alarm reset type
0=Manual reset, 1=Auto reset
Low pressure alarm reset
0=Manual reset, 1=Auto reset
Fan overload alarm reset type
0=Manual reset, 1=Auto reset
Pump overload alarm reset type
0=Manual reset, 1=Auto reset
Flow switch alarm reset type
0=Manual reset, 1=Auto reset
Auxiliary alarm reset type
0=Manual reset, 1=Auto reset
Antifreeze alarm reset type
0=Manual reset, 1=Auto reset
Comp overload contact type
0=Normally close(NC) 1=Normally open(NO)
High pressure contact type
0=Normally close(NC) 1=Normally open(NO)
Low pressure contact type
0=Normally close(NC) 1=Normally open(NO)
Fan overload contact type
0=Normally close(NC) 1=Normally open(NO)
Pump overload contact type
0=Normally close(NC) 1=Normally open(NO)
Flow switch contact type
0=Normally close(NC) 1=Normally open(NO)
External alarm contact type
0=Normally close(NC) 1=Normally open(NO)
Defrost end contact type
0=Normally close(NC) 1=Normally open(NO)
Unit
sec
sec
sec
Flag
°C (F)
°C (F)
Flag
Flag
Flag
Flag
Flag
Flag
Flag
Flag
Flag
Flag
Flag
Flag
Flag
Flag
Flag
43
Default
5 (41)
2 (3.6)
0
(leaving)
3 (37)
2 (3.6)
Min
-40 (-40)
0.4 (0.7)
0
Max
40 (104)
10 (18)
1
Resolution
1
0.1
1
-40 (-40)
0.4 (0.7)
40(104)
10 (18)
1
0.1
Default
5
120
30
0
(manual)
1
(auto)
1
(auto)
1
(auto)
0
(manual)
0
(manual)
1
(auto)
1
(auto)
0
(NC)
0
(NC)
0
(NC)
0
(NC)
0
(NC)
0
(NC)
0
(NC)
0
(NC)
Min
0
0
0
0
Max
199
199
199
1
Resolution
1
1
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
0
1
1
Precautions and Installation
Special Precautions When Dealing With Refrigerant R407C Unit
1) What is new refrigerant R407C?
R407C is a zeotropic refrigerant mixture which has Zero Ozone Depletion Potential (ODP = 0) and thus
conformed to the Montreal Protocol regulation. It requires Polyol-ester oil (POE) oil for its compressor’s
lubricant. Its refrigerant capacity and performance are about the same as the refrigerant R22.
2) Components
Mixture weight compositionR32(23%), R125(25%), R134a(52%)
3) Characteristic
•
R407C liquid and vapor components have different compositions when the fluid evaporates or condenses.
Hence, when leak occurs and only vapor leaks out, the composition of the refrigerant mixture left in the
system will change and subsequently affect the system performance. DO NOT add new refrigerant to
leaked system. It is recommended that the system should be evacuated thoroughly before recharging with
R407C.
•
When refrigerant R407C is used, the composition will differ depending on whether it is in gaseous or liquid
phase. Hence when charging R407C, ensure that only liquid is being withdrawn from the cylinder or can.
This is to make certain that only original composition of R407C is being charged into the system.
•
POE oil is used as lubricant for R407C compressor, which is different from the mineral oil used for R22
compressor. Extra precaution must be taken not to expose the R407C system too long to moist air.
4) Check list before installation/servicing
•
Tubing
Refrigerant R407C is more easily affected by dust of moisture compared with R22, make sure to temporarily
cover the ends of the tubing prior to installation
•
Compressor oil
No additional charge of compressor oil is permitted.
•
Refrigerant
No other refrigerant other that R407C
•
Tools
Tools specifically for R407C only (must not be used for R22 or other refrigerant)
i)
Manifold gauge and charging hose
ii) Gas leak detector
iii) Refrigerant cylinder/charging cylinder
iv) Vacuum pump c/w adapter
v) Flare tools
vi) Refrigerant recovery machine
5)
Handling and installation guidelines
Like R22 system, the handling and installation of R407C system are closely similar. All precautionary measures;
such as ensuring no moisture, no dirt or chips in the system, clean brazing using nitrogen, and thorough leak
check and vacuuming are equally important requirements. However, due to zeotropic nature of R407C and its
hydroscopic POE oil, additional precautions must be taken to ensure optimum and trouble free system operation.
a) Filter dryer must be installed along the liquid line for all R407C air conditioners. This is to minimise the
contamination of moisture and dirt in the refrigerant system. Filter dryer must be of molecular sieve type.
For a heat pump system, install a two--way flow filter dryer along the liquid line.
b) During installation or servicing, avoid prolong exposure of the internal part of the refrigerant system to
moist air. Residual POE oil in the piping and components can absorb moisture from the air.
44
c) Ensure that the compressor is not expose to open air for more than the recommended time specified by
its manufacturer (typically less than 10 minutes). Removed the seal plugs only when the compressor is
about to be brazed.
d) The system should be thoroughly vacuumed to 1.0 Pa ( 700mmHg) or lower. This vacuuming level is
more stringent than R22 system so as to ensure no incompressible gas and moisture in the system.
e) When charging R407C, ensure that only liquid is being withdrawn from the cylinder or can. This is to
ensure that only the original composition of R407C is being delivered into the system. The liquid composition
can be different from the vapor composition.
R32 / R125 / R134
23% / 25% / 52%
33% / 33% / 34%
Composition of R407C in vapour phase
is different from liquid phase.
f)
Normally, the R407C cylinder or can is being equipped with a dip pipe for liquid withdrawal. However, if the
dip pipe is not available, invert the cylinder or can so as to withdraw liquid from the valve at the bottom.
Dip-pipe
Invert cylinder
without dip-pipe
Liquid
withdrawal
g) When servicing leak, the top up method, commonly practiced for R22 system, is not recommended for
R407C system. Unlike R22 where the refrigerant is of a single component, the composition of R407C,
which made up of three different components, may have changed during the leak. Consequently, a top up
may not ensure that the R407C in the system is of original composition. This composition shift may
adversely affect the system performance. It is recommended that the system should be evacuated
thoroughly before recharging with R407C.
45
Special Precautions When Dealing With Refrigerant R410A Unit
1) What Is New Refrigerant R410A?
R410A is a new HFC refrigerant which does not damage the ozone layer. The working pressure of this new
refrigerant is 1.6 times higher than conventional refrigerant (R22), thus proper installation / servicing is
essential.
2) Components
Mixture of composition by weight : R32(50%) and R125(50%)
3) Characteristic
• R410A liquid and vapor components have different compositions when the fluid evaporates or
condenses. Hence, when leak occurs and only vapor leaks out, the composition of the refrigerant mixture
left in the system will change and subsequently affect the system performance. DO NOT add new
refrigerant to leaked system. It is recommended that the system be evacuated thoroughly before
recharging with R410A.
• When refrigerant R410A is used, the composition will differ depending on whether it is in gaseous or
liquid phase.
Hence when charging R410A, ensure that only liquid is being withdrawn from the cylinder or can. This is
to make certain that only original composition of R410A is being charged into the system.
• POE oil is used as lubricant for R410A compressor, which is different from the mineral oil used for R22
compressor.
Extra precaution must be taken to avoid exposing the R410A system to moist air.
4) Check List Before Installation / Servicing
• Tubing
Refrigerant R410A is more easily affected by dust or moisture compared with R22, make sure to
temporarily cover the ends of the tubing prior to installation
• Compressor oil
No additional charge of compressor oil is permitted.
• Refrigerant
No other refrigerant other that R410A
• Tools (size of service port is different from R22 system)
Tools specifically for R410A only (must not be used for R22 or other refrigerant)
i)
Gauge manifold and charging hose
ii) Gas leak detector
iii) Refrigerant cylinder/charging cylinder
iv) Vacuum pump c/w adapter
v) Flare tools
vi) Refrigerant recovery machine
5) Handling And Installation Guidelines
Like R22 systems, the handling and installation of R410A system are closely similar. All precautionary
measures; such as ensuring no moisture, no dirt or chips in the system, clean brazing using nitrogen, and
thorough leak check and vacuuming are equally important requirements. However, due to its hydroscopic
POE oil, additional precautions must be taken to ensure optimum and trouble-free system operation.
a) During installation or servicing, avoid prolong exposure of the internal part of the refrigerant system to
moist air. Residual POE oil in the piping and components can absorb moisture from the air.
b) Ensure that the compressor is not expose to open air for more than the recommended time specified by
its manufacturer (typically less than 10 minutes). Removed the seal-plugs only when the compressor is
about to be brazed.
c) The system should be thoroughly vacuumed to 1.0 Pa ( 700mmHg) or lower. This vacuuming level is
more stringent than R22 system so as to ensure no incompressible gas and moisture in the system.
46
d) When charging R410A, ensure that only liquid is being withdrawn from the cylinder or can. This is to
ensure that only the original composition of R410A is being delivered into the system. The liquid
composition can be different from the vapor composition.
Dip-pipe
Invert cylinder
without dip-pipe
Liquid
withdrawal
e) Normally, the R410A cylinder or can is being equipped with a dip-pipe for liquid withdrawal. However, if
the dip-pipe is not available, invert the cylinder or can so as to withdraw liquid from the valve at the
bottom.
47
Installations
M4AC/ MAC 020/ 025/ 030 C/CR, M5AC 020 / 025 / 030CR
M4AC/ MAC 040/ 050/ 060 C/CR, M5AC 040 / 050 / 055 CR
48
M4AC/ MAC 080/ 100/ 120/ 150 C/CR
500
MIN 500
M4AC / MAC 020 / 025 / 030 / 040 / 050 / 060C/CR, M5AC 020 / 025 / 030 / 040 / 050 /
055CR
500
1500
AIR FLOW
AIR FLOW
AIR FLOW
For single unit installation
49
500
M4AC / MAC 020 / 025 / 030 / 040 / 050 / 060 C/CR, M5AC 020 / 025 / 030 / 040 / 050 / 055 CR
500
1000
500
AIR FLOW
AIR FLOW
1500
AIR FLOW
1000
AIR FLOW
AIR FLOW
AIR FLOW
AIR FLOW
MIN 500
For multiple unit installation (mm)
50
100
50
For floor installation (mm)
Safety Precautions
Before installing the air conditioner unit, please read the following safety precautions carefully
!
•
•
•
•
•
•
•
Warning
Installation and maintenance should be performed by qualified persons who are familiar
with local code and regulation, and experienced with this type of appliance.
All field wiring must be installed in accordance with the national wiring regulation.
Ensure that the rated voltage of the unit corresponds to that of the name plate before
commencing wiring work according to the wiring diagram.
The unit must be GROUNDED to prevent possible hazards due to installation failure.
All electrical wiring must not touch the refrigerant piping, compressor or any moving parts
of the fan motors.
Confirm that the unit has been switched OFF before installing or servicing the unit.
Do not touch the compressor or refrigerant piping without wearing gloves.
IMPORTANT
DO NOT INSTALL OR USE THE AIR CONDITIONER UNIT IN A LAUNDRY ROOM
50
!
Caution
Please take note of the following important points when installing.
•
Do not install the unit where leakage of flammable gas may occur.
If gas leaks and accumulates around the unit, it may cause fire ignition.
•
Ensure that the drainage piping is connected properly.
!
•
If the drainage piping is not connected properly, it may cause water leakage which will dampen the
furniture.
Do not overcharge the unit.
This unit is factory pre-charged. Overcharge will cause over-current or damage to the compressor.
•
Ensure that the units panel is closed after service or installation.
!
Unsecured panels will cause unit to operate noisily.
Installation Location
• Installation work should be done by the authorized dealer or qualified contractor. Never install the unit
yourself.
• Make sure there is sufficient airflow around the unit.
• Vibration isolator should be provided to reduce the vibration and noise of the unit.
• There should be sufficient space allocated for servicing and maintenance when installing the unit.
Transportation
• The unit should be lifted using a crane. Ensure that the hanger belts
are not touching the coil, top panel and front panel (use protective panel)
as shown in Figure 1.
• The bolt of the base and channel support can be removed after
putting the unit on the fixed location.
Figure 1
Water Piping and Fitting
• All water pipe must be insulated to prevent capacity losses and condensation.
• Install a 40-60 mesh strainer to ensure water quality is good.
• Water pipe recommended are black steel pipe and copper pipe.
• During installation, the piping of the unit should be clamp before rotating the installation pipe to reduce the
moment induce on the unit piping.
• Users are recommended to install the pipe and accessories as shown in Figure 2 & 3.
• An air vent must be installed at the highest position, while a drainage plug at the lowest position of the
water circuit. Open the air vent to release any air trap in the water circuit.
• Run the clean water through the water inlet and operate the pump to drain out the dirty water. Clean
the strainer after running the pump for 30 minutes.
• Fill up the water circuit after connecting the pipes and equipment. Check water leakage at all
connections and joints. Do not start the unit when the system is leaking.
• To optimize the capacity of the system, ensure that the system is free of air bubbles. The air trapped
in the system would make the system unbalanced.
51
M4AC / MAC / 020 / 025 / 030 C/CR, M5AC 020 / 025 / 030 CR
AIRVENT (INSTALL
T
HIGHEST POSITION)
PRESSURE GAUGE
GATE
A
VALVE
GATE
A
VALVE
GATE
A
BALANCING
VALVE
VALVE
THERMOMETER
FAN COIL
L UNIT/AIR HANDLING UNIT
THERMOMETER
GATE
A E VALV
L E
VALVE
GATE
A VALV
L E
P
BYP
P
(DIFFER ENT
ALV
L E
STRAINER
FLEXIBLE
GATE
A VAL
LVE (LOWER
POSITION FOR DRAINAGE)
CHECK
VALVE
MAKE UP
VALVE
M4AC / MAC / 040 / 050 / 060 C/CR, M5AC 040 / 050 / 055 CR
AIRVENT (INSTALL
T
HIGHEST POSITION)
PRESSURE GAUGE
GA
A
VA E
GATE
A
VALVE
GA
A
THERMOMETER
FAN COIL
L UNIT/AIR HANDLING UNIT
THERMOMETER
BYP
P
ALV
L E
P (DIFFER ENT
VALVE
STRAINER
FLEXIBLE
ALV
L
TYPE)
AL
LVE (LOWER
VALV
L E
MAKE UP
VALVE
Figure 2
M4AC / MAC 080 / 100 / 120 / 150 C/CR
AIRVENT (INSTALL
HIGHEST POSITION)
PRESSURE GAUGE
GATE
VALVE
GATE
VALVE
GATE
VALVE
THERMOMETER
BALANCING
VALVE
FAN COIL UNIT/AIR HANDLING UNIT
FLEXIBLE
THERMOMETER
GATE
VALVE
BALANCING
VALVE
STRAINER
FLEXIBLE
CHECK
VALVE
GATE
VALVE
PRESSURE
DIFFERENTIAL
VALVE
GATE VALVE
(LOWER POSITION
FOR DRAINAGE)
MAKE UP
VALVE
!
Figure 3
CAUTION
• Do not allow water to remain in the water pipes if the unit is not operating for a long period.
•
Water must be drained out if the unit is not running during winter. Failing to do so would cause the pipe
to crack.
Do not drink the chilled water in the unit.
52
Electrical And Wiring
•
Refer to the wiring diagram provided on the unit when making electrical wiring.
• Install an isolator (optional) to prevent electrical shock.
• Do not ground any electrical equipment to the water piping.
• Operation of the mini chiller without any fan speed controller (Field supply) is limited to an ambient
temperature of 20C. With the fan speed controller (Field supply), the unit is able to operate down
to -5C.
All mini chillers will have a 1/4” access valve provided for along the liquid
line of the refrigerant circuit.This valve is for direct pressure connection
to the fan speed controller. To install the fan speed controller, screw in
the female adaptor to the 1/4” access valve. Use a pair of spanners to
tighten properly(max. torque 15Nm). See Fig. 8. Ensure there is no leakage at
the joint. Wire the fan speed controller to the terminal blocks.
TO (PCB)
OUT_FAN1
OF IN
L/L1
N/L2
OF OUT
L1
Remove this wire
when doing wiring
for fan speed
controller
OF IN OF OUT
M4AC / MAC 020 / 025 / 030C/CR
M5AC 020 / 025CR
FSC
TO (PCB)
OUT_FAN1
F
TO (A) OUT_FAN1
CAPACIT
P
OR
TB1
OF IN
N
Power supply 230V / 1Ph-N / 50Hz
TB3
Wiring for fan
speed controller
(FSC)
TB3
Figure 8
TO (A) OUT_FAN1
CAPACIT
P
OR
TB1
TB3
15 Nm
R
S
L1
L2
T
N
OF OUT
Remove this wire
when doing
wiring for fan
speed controller
L3
N
Power supply 400V / 3Ph-N / 50Hz
TB3 OF IN OF OUT
Wiring for fan
speed controller
(FSC)
M4AC / MAC 040 / 050 / 060C/CR
M5AC 030 / 040 / 050 / 055CR
FSC
12 VDC or 230V AC
H C OFF ON
4WV 4WV HTR ALL ALL FM1 FM2 OF1 OF2 C / H ON/
1
2
IN
OFF
Remove these wires
when do wiring for fan
speed controller
Wiring for fan speed
controller (FSC)
Power supply 415V / 3Ph-N / 50Hz
FM1
FM2
OF1
OF2
M4AC / MAC 080 / 100 / 120 / 150C/CR
FSC1
FSC2
53
5HFRPPHQGHGIXVHDQGFDEOHVL]HV
0RGHO
0$&&&5
0$&&&5
9ROWDJHUDQJH
0$&&&5
0$&&&5
0$&&&5
0$&&&5
0$&&&5
0$&&&5
93K+]
1
0$&&&5
0$&&&5
0$&&&5
0$&&&5
93K+]1
5HFRPPHQGHGIXVH$
3RZHUVXSSO\FDEOHVL]HPP 1XPEHUVRIFRQGXFWRU
,QWHUFRQQHFWLRQFDEOHVL]HPP
0RGHO
0$&&&5
0$&&&5
0$&&&5
0$&&&5
9ROWDJHUDQJH
5HFRPPHQGHGIXVH$
3RZHUVXSSO\FDEOHVL]HPP 1XPEHUVRIFRQGXFWRU
,QWHUFRQQHFWLRQFDEOHVL]HPP
93K+]1
0$&&&5
0$&&&5
0$&&&5
0$&&&5
0RGHO
9ROWDJHUDQJH
5HFRPPHQGHGIXVH$
3RZHUVXSSO\FDEOHVL]HPP 1XPEHUVRIFRQGXFWRU
,QWHUFRQQHFWLRQFDEOHVL]HPP
0RGHO
0$&&5
0$&&5
0$&&5
0$&&5
93K+]1
9ROWDJHUDQJH
5HFRPPHQGHGIXVH$
3RZHUVXSSO\FDEOHVL]HPP 1XPEHUVRIFRQGXFWRU
,QWHUFRQQHFWLRQFDEOHVL]HPP
93K+]1
0RGHO
0$&&5
0$&&5
9ROWDJHUDQJH
5HFRPPHQGHGIXVH$
3RZHUVXSSO\FDEOHVL]HPP 1XPEHUVRIFRQGXFWRU
,QWHUFRQQHFWLRQFDEOHVL]HPP
93K+]1
93K+]1
,03257$17
7KHILJXUHVVKRZQLQWKHWDEOHDUHIRULQIRUPDWLRQSXUSRVHRQO\7KH\VKRXOGEHFKHFNHGDQGVHOHFWHGWRFRPSO\ZLWKWKH
ORFDOQDWLRQDOFRGHVRIUHJXODWLRQV7KLVLVDOVRVXEMHFWHGWRWKHW\SHRILQVWDOODWLRQDQGFRQGXFWRUVXVHG
7KHDSSURSULDWHYROWDJHUDQJHVKRXOGEHFKHFNHGZLWKODEHOGDWDRQWKHXQLW
v
v
v
v
v
v
v
&$87,21
$OOILHOGZLULQJPXVWEHLQVWDOOHGLQDFFRUGDQFHZLWKWKHQDWLRQDOZLULQJUHJXODWLRQ
$OOWKHWHUPLQDOVDQGFRQQHFWLRQVPXVWEHWLJKWHQHG,PSURSHUFRQQHFWLRQDQGIDVWHQLQJVFRXOGFDXVHHOHFWULF
VKRFNVKRUWFLUFXLWDQGILUH
(QVXUHWKDWWKHUDWHGYROWDJHRIWKHXQLWFRUUHVSRQGVWRWKDWRIWKHQDPHSODWHEHIRUHFRPPHQFLQJZLULQJZRUN
DFFRUGLQJWRWKHZLULQJGLDJUDP
7KHXQLWPXVEH*5281'('WRSUHYHQWSRVVLEOHKD]DUGVGXHWRLQVXODWLRQIDLOXUH
$OOHOHFWULFDOZLULQJPXVWQRWWRXFKWKHUHIULJHUDQWSLSLQJFRPSUHVVRUSXPSIDQPRWRURUDQ\PRYLQJSDUWVRIWKH
IDQPRWRUV
'RQRWRSHUDWHWKHFKLOOHUZLWKZHWKDQGV,WZRXOGUHVXOWLQHOHFWULFVKRFN
'RQRWXVHIXVHRIGLIIHUHQWDPSHUDJHWKDQVWDWHG8VLQJZLUHHWFWRUHSODFHDIXVHFRXOGFDXVHHTXLSPHQW
GDPDJHRUILUH
54
!
WARNING
•
All terminals and connection must be tightened.
• Avoid any wires from touching the refrigerant pipe. Apply insulation if necessary.
• Avoid any wires from touching the moving components such as, fan motor, pump & compressor.
Water Piping System Setup
•
Fill up the water circuit after connecing all the pipes and equipment. Perform leak checks for all
connections and joints. Do not start the unit when the system is leaking.
• To optimize the capacity of the system, ensure that the system is free of air bubbles.
The air trapped in the system would make the system unbalanced.
• Ensure that the water tank (optional) is not full. This is to ensure optimal performance of the mini chiller. If
the pressure is too high, release the air trapped from the auto air vent (on the tank) and manual air
vent (installed on the water system).
Refrigerant Circuit
•
All mini chillers units are pre-charged with R22, R407C or R410A refrigerant. The only piping that needs
to be done is the water piping from mini chiller (outdoor) to the fan coil unit (indoor).
Safety And Caution
It is advisable to read through all the safety precautions before installing and commissioning of the unit.
• Contact your dealer for installation, reinstallation or dismantling of unit. Improper handling of unit could
result in leaks, electrical shock or unit malfunction.
• Use the controller handset to switch on/off the unit. Do not plug off the main power supply directly, it would
cause the unit to breakdown.
• Improper connections and fastening could cause electric shock, short circuit and fire.
• Do not introduce foreign objects such as fingers, sticks etc. into the air inlet and outlet.
• Do not spray any chemical agents or flammable agents to the unit. It would cause fire or explosion.
• Do not climb or place objects on top of the mini chiller.
• Do not operate the chiller with wet hands. It would result in electric shock.
• Do not use fuse of different amperage than stated. Using wire, etc. to replace a fuse could cause
equipment damage or fire.
• Provide proper grounding for the mini chiller. Do not connect the ground wire to gas piping, water piping,
lighting rods or telephone ground wire. Improper grounding could cause electrical shock.
• Do not attempt to do any service or maintenance when unit is operating.
• Do not change the settings of the safety devices.
• Do not consume the chilled water in the unit.
• Do not allow water to remain in the water pipes if the unit is not operating for a long period. Water must
be drained out if the unit is not running during winter. Failing to do so would cause the pipe to crack.
•
Do not touch the aluminum fin coil. It would damage the coil or cause injury.
!
Caution
•
R407C / R410A must be charged as liquid. Usually R407C / R410A cylinder is equipped with a
dip-pipe for liquid withdrawal. If there is no dip-pipe, the cylinder should be inverted so as to
withdraw liquid R407C / R410A from the valve.
• Do not top-up when servicing leak, as this will reduce the unit performance. Vacuum the unit
thoroughly and then charge the unit with fresh R407C / R410A according to the amount
recommended in the specification.
55
Control Operation Guide
The unit is equipped with a microprocessor controller board. The microprocessor contorller is provided to
give temperature control for the system by accurately measuring the ambient temperature, and controlling
the water entering and water leaving temperature. The temperature setting in teh unit is preset in the factory.
It is not recommended to chage the setting unless necessary. A wired contoller handset is connected to the
microprocessor board. Every parameter setting and reading can be observed from the LCD of the handset.
1. Handset location
The handset is located on a metal bracket behind the right door panel.
2. LED Display (microprocessor board)
The keypad LED will light up when the unit is turned on.
3. LCD display (contoller handset)
During normal operations, the LCD can display the entering water temperature, the leaving water
temperatur, the entering water setpoint temperature, compressor on or off status and outdoor air
temperature. When malfunctioning occurred, the LCD would blink. The display would show the faulty
parameter and the date and time of the occurance.
4. Controller functioning specification
There is a 3 minute delay for the compressor and fan motor to restart (default setting). During defrosting,
fan motor is not running.
56
Sound Data
MAC/M4AC020C/CR, M5AC020CR NC CURVE
Sound Pressure level (dB, ref 20µPa)
80
70
60
NC-60
NC-55
50
NC-50
NC-45
40
NC-40
NC-35
30
NC-30
20
10
0
125
250
500
1000
2000
4000
8000
Octave-band frequency (Hz)
MAC/M4AC025C/CR, M5AC025CR NC CURVE
80
Sound Pressure level (dB, ref 20µPa)
70
60
NC-60
NC-55
50
NC-50
NC-45
40
NC-40
NC-35
30
NC-30
20
10
0
125
250
500
1000
2000
Octave-band frequency (Hz)
57
4000
8000
MAC/M4AC030C/CR NC CURVE
Sound Pressure level (dB, ref 20µPa)
80
70
60
NC-60
50
NC-50
NC-55
NC-45
40
NC-40
30
NC-30
NC-35
20
10
0
125
250
500
1000
2000
4000
8000
Octave-band frequency (Hz)
MAC/M4AC040C/CR NC CURVE
80
Sound Pressure level (dB, ref 20µPa)
70
60
NC-60
NC-55
50
NC-50
40
NC-45
NC-40
NC-35
30
NC-30
20
10
0
125
250
500
1000
2000
Octave-band frequency (Hz)
58
4000
8000
MAC/M4AC050C/CR NC CURVE
70
60
NC-60
NC-55
50
NC-50
40
NC-45
NC-40
NC-35
30
NC-30
20
10
0
125
250
500
1000
2000
4000
8000
Octave-band frequency (Hz)
MAC/M4AC060C/CR NC CURVE
80
70
Sound Pressure level (dB, ref 20µPa)
Sound Pressure level (dB, ref 20µPa)
80
60
NC-60
NC-55
50
NC-50
NC-45
NC-45
40
NC-40
NC-35
NC-35
30
NC-30
20
10
0
125
250
500
1000
2000
Octave-band frequency (Hz)
59
4000
8000
MAC/M4AC080C/CR NC CURVE
Sound Pressure level (dB, ref 20µPa)
90
80
70
NC-70
NC-65
60
NC-60
NC-55
50
NC-50
NC-45
40
NC-40
30
20
10
0
125
250
500
1000
2000
4000
8000
Octave-band frequency (Hz)
MAC/M4AC 100C/CR NC CURVE
90
Sound Pressure level (dB, ref 20µPa)
80
NC-70
70
NC-65
60
NC-60
NC-55
50
NC-50
NC-45
40
NC-40
30
20
10
0
125
250
500
1000
2000
Octave-band frequency (Hz)
60
4000
8000
MAC/M4AC 120C/CR NC CURVE
Sound Pressure level (dB, ref 20µPa)
90
80
NC-70
70
NC-65
60
NC-60
NC-55
50
NC-50
NC-45
40
NC-40
30
20
10
0
125
250
500
1000
2000
4000
8000
Octave-band frequency (Hz)
MAC/M4AC 150C/CR NC CURVE
Sound Pressure level (dB, ref 20µPa)
90
80
NC-70
70
NC-65
60
NC-60
NC-55
50
NC-50
NC-45
40
NC-40
30
20
10
0
125
250
500
1000
2000
Octave-band frequency (Hz)
61
4000
8000
M5AC030C/CR NC CURVE
80
Sound pressure level (dB, ref 20µPa)
70
60
NC-60
NC-55
50
NC-50
NC-45
40
NC-40
NC-35
30
NC-30
20
10
0
125
250
500
1000
2000
4000
8000
Octave-band frequency (Hz)
M5AC040C/CR NC CURVE
Sound pressure level (dB, ref 20µPa)
80
70
NC-60
60
NC-55
50
NC-50
NC-45
40
NC-40
NC-35
30
NC-30
20
10
0
125
250
500
1000
2000
Octave-band frequency (Hz)
62
4000
8000
M5AC050C/CR NC CURVE
80
Sound pressure level (dB, ref 20µPa)
70
NC-60
60
NC-55
50
NC-50
NC-45
40
NC-40
NC-35
30
NC-30
20
10
0
125
250
500
1000
2000
4000
8000
Octave-band frequency (Hz)
M5AC055C/CR NC CURVE
80
Sound pressure level (dB, ref 20µPa)
70
60
NC-60
NC-55
50
NC-50
NC-45
40
NC-40
NC-35
30
NC-30
20
10
0
125
250
500
1000
2000
Octave-band frequency (Hz)
63
4000
8000
Selection Process
Water Pressure Drop vs Flow Rate
Model : MAC/M4AC020C/CR
Water Flow
m3/hr
0.6
0.8
1.0
1.2
1.4
Pump Head kPa
System Head kPa
117.0
115.0
114.0
112.0
108.0
12.0
25.0
34.0
50.0
59.9
Available Head Presure
kPa
105.0
90.0
80.0
62.0
48.1
Model : MAC/M4AC025C/CR
Water Flow
m3/hr
0.7
0.8
1.0
1.3
1.5
1.8
Pump Head kPa
System Head kPa
116.0
116.0
114.0
110.0
105.0
100.0
10.4
10.8
15.2
20.9
27.9
35.2
Available Head Presure
kPa
105.6
105.2
98.8
89.1
77.1
64.8
Model : MAC/M4AC030C/CR, M5AC030CR
Water Flow
m3/hr
0.9
1.2
1.5
1.8
2.1
Pump Head kPa
System Head kPa
115.0
112.0
105.0
98.0
90.0
7.4
12.3
19.6
29.4
36.8
Available Head Presure
kPa
107.6
99.7
85.4
68.6
53.2
Model : MAC/M4AC040C/CR, M5AC040CR
Water Flow
m3/hr
1.2
1.6
2.0
2.4
2.8
Pump Head kPa
System Head kPa
168.0
162.0
144.0
137.0
113.0
26.3
26.5
34.3
49.5
62.5
Available Head Presure
kPa
141.7
135.5
109.7
87.5
50.5
Model : MAC/M4AC050C/CR, M5AC050CR
Water Flow
m3/hr
1.5
2.0
2.5
3.0
Pump Head kPa
System Head kPa
163.0
144.0
126.0
107.0
15.0
25.7
39.4
52.6
64
Available Head Presure
kPa
148.0
118.3
86.6
54.4
Model : MAC/M4AC060C/CR, M5AC055CR
Water Flow
m3/hr
1.8
2.4
3.0
3.2
Pump Head kPa
System Head kPa
150.0
137.0
107.0
69.0
10.5
22.8
39.0
41.8
Available Head Presure
kPa
139.5
114.2
68.0
27.2
Model : MAC/M4AC080C/CR
Water Flow
m3/hr
2.4
3.2
4.0
4.8
5.6
6.4
Pump Head kPa
System Head kPa
300.0
270.0
260.0
230.0
200.0
175.0
18.7
32.6
49.3
69.6
93.5
121.0
Available Head Presure
kPa
281.3
237.4
210.7
160.4
106.5
54.0
Model : MAC/M4AC100C/CR
Water Flow
m3/hr
3.0
4.0
5.0
6.0
7.0
Pump Head kPa
System Head kPa
280.0
260.0
220.0
180.0
150.0
22.9
39.3
59.8
84.2
112.6
Available Head Presure
kPa
257.1
220.7
160.2
95.8
37.4
Model : MAC/M4AC120C/CR
Water Flow
m3/hr
3.0
4.0
5.0
6.0
7.0
Pump Head kPa
System Head kPa
280.0
270.0
260.0
250.0
230.0
16.6
28.6
43.6
61.5
82.4
Available Head Presure
kPa
263.4
241.4
216.4
188.5
147.6
Model : MAC/M4AC150C/CR
Water Flow
m3/hr
3.0
4.0
5.0
6.0
7.0
8.0
Pump Head kPa
System Head kPa
280.0
270.0
260.0
250.0
230.0
210.0
13.8
23.7
36.0
50.7
67.8
87.1
65
Available Head Presure
kPa
266.2
246.3
224.0
199.3
162.2
122.9
Correction Factors With Glycol Use
LWT/ deg C
-5
-3.9
-1.1
1.7
4.4
7.2
10
10
0.925
0.945
0.956
0.965
0.962
GYLCOL %
WATER FLOW
10
20
30
40
1.015
1.04
1.08
1.135
CAPACITY FACTOR
GLYCOL
20
30
0.89
0.87
0.9
0.876
0.925
0.892
0.938
0.906
0.949
0.918
0.959
0.927
0.957
0.926
PRESSURE
DROP
1.06
1.12
1.18
1.24
66
40
0.77
0.781
0.796
0.809
0.82
0.829
0.828
Engineering and Physical Data
General Data - R22 Cooling only
MODEL
NOMINAL COOLING CAPACITY
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
POWER SOURCE
MAC020C
MAC025C
Btu/h
18000
23500
W
5275
6887
W
2669
2730
A
12.6
R22
REFRIGERANT TYPE
CONTROL
UNIT DIMENSION
PACKING DIMENSION
12.6
220-240 / 1 / 50
V/Ph/Hz
CAPILLARY TUBE
HEIGHT
mm/in
800 / 31.5
WIDTH
mm/in
1160 / 45.7
DEPTH
mm/in
460 / 18.1
HEIGHT
mm/in
958 / 37.7
WIDTH
mm/in
1309 / 51.5
DEPTH
mm/in
574 / 22.6
UNIT WEIGHT
kg/lb
116 / 256
123 / 271
SOUND PRESSURE LEVEL
dBA
57
57
l/s / m3/hr
0.25 / 0.9
0.33 / 1.2
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
TYPE/DRIVE
PROPELLER / DIRECT
QUANTITY
1
1
HYDRAULIC KIT
HIGH HEAD CIRCULATOR
TYPE
PUMP
PIPING
TANK
MAX. WATER OPER. PRESSURE
kPa / psi
WATER FLOW RATE
l/s / m3/hr
INSTALLATION PIPE CONNECITON
HEAD
1000 / 145
0.25 / 0.9
m
9.2
9.5
MILD STEEL COATED WITH ZING
MATERIAL
CAPACITY/VOLUME
0.33 / 1.2
25.4 / 1
mm/in
L / ft3
22 / 0.78
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
ROTARY
SCROLL
0 - 100%
0 - 100%
1.1 / 2.4
1.8 / 4.0
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
67
General Data - R22 Cooling only
MODEL
MAC030C
MAC040C
Btu/h
27500
40000
W
8059
11723
NOMINAL TOTAL INPUT POWER
W
3491
4470
NOMINAL RUNNING CURRENT
A
16.6
8.8
V/Ph/Hz
220-240 / 1 / 50
380-415 / 3 / 50
NOMINAL COOLING CAPACITY
POWER SOURCE
R22
REFRIGERANT TYPE
CONTROL
UNIT DIMENSION
CAPILLARY TUBE
HEIGHT
mm/in
800 / 31.5
1410 / 55.5
WIDTH
mm/in
1160 / 45.7
1160 / 45.7
DEPTH
mm/in
460 / 18.1
460 / 18.1
HEIGHT
mm/in
958 / 37.7
1578 / 62.1
WIDTH
mm/in
1309 / 51.5
1309 / 51.5
DEPTH
mm/in
574 / 22.6
574 / 22.6
UNIT WEIGHT
kg/lb
128 / 282
195 / 430
SOUND PRESSURE LEVEL
dBA
58
60
l/s / m3/hr
0.39 / 1.4
0.56 / 2.0
PACKING DIMENSION
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
TYPE/DRIVE
PROPELLER / DIRECT
QUANTITY
1
2
HYDRAULIC KIT
TYPE
PUMP
PIPING
TANK
HIGH HEAD CIRCULATOR
MAX. WATER OPER. PRESSURE
kPa / psi
WATER FLOW RATE
l/s / m3/hr
INSTALLATION PIPE CONNECITON
HEAD
0.39 / 1.4
0.56 / 2.0
25.4 / 1
mm/in
m
9.6
9.7
MILD STEEL COATED WITH ZING
MATERIAL
CAPACITY/VOLUME
HORIZONTAL MULTISTAGE END-SUCTION
1000 / 145
L / ft3
22 / 0.78
40 / 1.41
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
SCROLL
SCROLL
0 - 100%
0 - 100%
1.6 / 3.5
2.7 / 6.0
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
68
General Data - R22 Cooling only
MODEL
MAC050C
MAC060C
Btu/h
50000
53000
W
14654
15533
NOMINAL TOTAL INPUT POWER
W
5245
6361
NOMINAL RUNNING CURRENT
A
9.3
NOMINAL COOLING CAPACITY
POWER SOURCE
R22
REFRIGERANT TYPE
CAPILLARY TUBE
CONTROL
UNIT DIMENSION
PACKING DIMENSION
12.3
380-415 / 3 / 50
V/Ph/Hz
HEIGHT
mm/in
1410 / 55.5
WIDTH
mm/in
1160 / 45.7
DEPTH
mm/in
460 / 18.1
HEIGHT
mm/in
1578 / 62.1
WIDTH
mm/in
1309 / 51.5
DEPTH
mm/in
574 / 22.6
UNIT WEIGHT
kg/lb
196 / 432
203 / 448
SOUND PRESSURE LEVEL
dBA
60
61
l/s / m3/hr
0.70 / 2.5
0.74 / 2.7
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
TYPE/DRIVE
PROPELLER / DIRECT
QUANTITY
2
2
HYDRAULIC KIT
HORIZONTAL MULTISTAGE END-SUCTION
TYPE
PUMP
PIPING
TANK
MAX. WATER OPER. PRESSURE
kPa / psi
WATER FLOW RATE
l/s / m3/hr
INSTALLATION PIPE CONNECITON
HEAD
1000 / 145
0.70 / 2.5
m
7.5
8.3
MILD STEEL COATED WITH ZINC
MATERIAL
CAPACITY/VOLUME
0.74 / 2.7
25.4 / 1
mm/in
L / ft3
40 / 1.41
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
SCROLL
SCROLL
0 - 100%
0 - 100%
3.1 / 6.8
3.1 / 6.8
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
69
General Data - R22 Cooling only
MODEL
MAC080C
MAC100C
Btu/h
78000
93000
W
22860
27257
NOMINAL TOTAL INPUT POWER
W
8667
10175
NOMINAL RUNNING CURRENT
A
16.3
NOMINAL COOLING CAPACITY
POWER SOURCE
17.0
380-415 / 3 / 50
V/Ph/Hz
REFRIGERANT TYPE
R22
CONTROL
TXV
UNIT DIMENSION
PACKING DIMENSION
HEIGHT
mm/in
1245 / 49.0
WIDTH
mm/in
1500 / 59.1
DEPTH
mm/in
900 / 35.4
HEIGHT
mm/in
1452 / 57.2
WIDTH
mm/in
1732 / 68.2
DEPTH
mm/in
1032 / 40.6
UNIT WEIGHT
kg/lb
340 / 750
350 / 772
SOUND PRESSURE LEVEL
dBA
65
66
l/s / m3/hr
1.08 / 3.9
1.31 / 4.7
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
TYPE/DRIVE
PROPELLER / DIRECT
QUANTITY
2
2
HYDRAULIC KIT
TYPE
PUMP
PIPING
TANK
HORIZONTAL MULTISTAGE END-SUCTION
MAX. WATER OPER. PRESSURE
kPa / psi
WATER FLOW RATE
l/s / m3/hr
INSTALLATION PIPE CONNECITON
HEAD
1000 / 145
1.08 / 3.9
m
21.6
MATERIAL
CAPACITY/VOLUME
1.31 / 4.7
42 / 1 1/4"
mm/in
18.7
NA
L / ft3
NA
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
SCROLL
SCROLL
0 - 50 - 100%
0 - 50 - 100%
4.5 x2 / 9.9 x2
3.9 x2 / 8.6 x2
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
70
General Data - R22 Cooling only
MODEL
MAC120C
MAC150C
Btu/h
116000
138000
W
33998
40445
NOMINAL TOTAL INPUT POWER
W
11005
13779
NOMINAL RUNNING CURRENT
A
22.9
NOMINAL COOLING CAPACITY
POWER SOURCE
26.7
380-415 / 3 / 50
V/Ph/Hz
REFRIGERANT TYPE
R22
CONTROL
TXV
UNIT DIMENSION
PACKING DIMENSION
HEIGHT
mm/in
1245 / 49.0
WIDTH
mm/in
1800 / 70.9
DEPTH
mm/in
1150 / 45.3
HEIGHT
mm/in
1452 / 57.2
WIDTH
mm/in
2032 / 80.0
DEPTH
mm/in
1282 / 50.5
UNIT WEIGHT
kg/lb
460 / 1014
540 / 1190
SOUND PRESSURE LEVEL
dBA
67
69
l/s / m3/hr
1.67 / 6.0
2.00 / 7.2
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
TYPE/DRIVE
PROPELLER / DIRECT
QUANTITY
2
2
HYDRAULIC KIT
HORIZONTAL MULTISTAGE END-SUCTION
TYPE
PUMP
PIPING
TANK
MAX. WATER OPER. PRESSURE
kPa / psi
WATER FLOW RATE
l/s / m3/hr
INSTALLATION PIPE CONNECITON
HEAD
1000 / 145
1.67 / 6.0
m
19.2
16.5
NA
MATERIAL
CAPACITY/VOLUME
2.00 / 7.2
42 / 1 1/4"
mm/in
L / ft3
NA
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
SCROLL
SCROLL
0 - 50 - 100%
0 - 50 - 100%
6.0 x2 / 13.2 x2
7.1 x2 / 15.7 x2
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
71
General Data - R22 Heat pump
MODEL
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
MAC020CR
MAC025CR
Btu/h
18000
23000
W
5275
6740
Btu/h
22000
25000
W
6448
7327
COOLING
W
2599
2779
HEATING
W
2770
2614
COOLING
A
12.3
12.7
HEATING
A
12.7
POWER SOURCE
12.0
220-240 / 1 / 50
V/Ph/Hz
R22
REFRIGERANT TYPE
CAPILLARY TUBE
CONTROL
UNIT DIMENSION
PACKING DIMENSION
HEIGHT
mm/in
800 / 31.5
WIDTH
mm/in
1160 / 45.7
DEPTH
mm/in
460 / 18.1
HEIGHT
mm/in
958 / 37.7
WIDTH
mm/in
1309 / 51.5
DEPTH
mm/in
574 / 22.6
UNIT WEIGHT
kg/lb
116 / 256
123 / 271
SOUND PRESSURE LEVEL
dBA
57
57
COOLING
l/s / m3/hr
0.25 / 0.9
0.32 / 1.2
HEATING
l/s / m3/hr
0.31 / 1.1
0.35 / 1.3
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
PROPELLER / DIRECT
TYPE/DRIVE
QUANTITY
1
1
HYDRAULIC KIT
HIGH HEAD CIRCULATOR
TYPE
PUMP
MAX. WATER OPER. PRESSURE
WATER FLOW RATE
COOLING
l/s / m3/hr
0.25 / 0.9
HEATING
l/s / m3/hr
0.31 / 1.1
INSTALLATION PIPE CONNECITON
PIPING
TANK
HEAD
1000 / 145
kPa / psi
0.32 / 1.2
0.35 / 1.3
25.4 / 1
mm/in
COOLING
m
9.2
9.6
HEATING
m
7.2
9.1
MILD STEEL COATED WITH ZINC
MATERIAL
CAPACITY/VOLUME
3
22 / 0.78
L / ft
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
ROTARY
SCROLL
0 - 100%
0 - 100%
1.6 / 3.5
1.9 / 4.2
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
b) HEATING - 40°C / 45°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 7°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
72
General Data - R22 Heat pump
MODEL
MAC030CR
MAC040CR
Btu/h
27500
40000
W
8060
11723
Btu/h
31500
43000
W
9232
12602
COOLING
W
3541
4560
HEATING
W
3561
4629
COOLING
A
18.3
8.6
HEATING
A
18.4
8.8
V/Ph/Hz
220-240 / 1 / 50
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
POWER SOURCE
380-415 / 3 / 50
REFRIGERANT TYPE
R22
CONTROL
UNIT DIMENSION
PACKING DIMENSION
CAPILLARY TUBE
HEIGHT
mm/in
800 / 31.5
1410 / 55.5
WIDTH
mm/in
1160 / 45.7
1160 / 45.7
460 / 18.1
460 / 18.1
DEPTH
mm/in
HEIGHT
mm/in
958 / 37.7
1578 / 62.1
WIDTH
mm/in
1309 / 51.5
1309 / 51.5
DEPTH
mm/in
574 / 22.6
574 / 22.6
UNIT WEIGHT
kg/lb
128 / 282
195 / 430
SOUND PRESSURE LEVEL
dBA
58
60
COOLING
l/s / m3/hr
0.39 / 1.4
0.56 / 2.0
HEATING
l/s / m3/hr
0.44 / 1.6
0.60 / 2.2
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
PROPELLER / DIRECT
TYPE/DRIVE
QUANTITY
2
2
HYDRAULIC KIT
TYPE
PUMP
HIGH HEAD CIRCULATOR
MAX. WATER OPER. PRESSURE
WATER FLOW RATE
COOLING
l/s / m3/hr
0.39 / 1.4
HEATING
l/s / m3/hr
0.44 / 1.6
INSTALLATION PIPE CONNECITON
PIPING
TANK
HEAD
HORIZONTAL MULTISTAGE END-SUCTION
1000 / 145
kPa / psi
0.56 / 2.0
0.60 / 2.2
25.4 / 1
mm/in
COOLING
m
9.5
9.7
HEATING
m
8.2
8.8
MILD STEEL COATED WITH ZINC
MATERIAL
CAPACITY/VOLUME
3
22 / 0.78
L / ft
40 / 1.41
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
ROTARY
SCROLL
0 - 100%
0 - 100%
1.8 / 4.0
3.0 / 6.6
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
b) HEATING - 40°C / 45°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 7°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
73
General Data - R22 Heat pump
MODEL
MAC050CR
MAC060CR
Btu/h
46000
53000
W
13481
15533
Btu/h
52000
59000
W
15240
17292
COOLING
W
5046
6551
HEATING
W
4999
6247
COOLING
A
8.9
13.4
HEATING
A
8.9
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
POWER SOURCE
13.0
380-415 / 3 / 50
V/Ph/Hz
R22
REFRIGERANT TYPE
CONTROL
UNIT DIMENSION
PACKING DIMENSION
CAPILLARY TUBE
HEIGHT
mm/in
1410 / 55.5
WIDTH
mm/in
1160 / 45.7
DEPTH
mm/in
460 / 18.1
HEIGHT
mm/in
1578 / 62.1
WIDTH
mm/in
1309 / 51.5
DEPTH
mm/in
574 / 22.6
UNIT WEIGHT
kg/lb
196 / 432
203 / 448
SOUND PRESSURE LEVEL
dBA
60
61
COOLING
l/s / m3/hr
0.64 / 2.3
0.74 / 2.7
HEATING
l/s / m3/hr
0.73 / 2.6
0.83 / 3.0
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
PROPELLER / DIRECT
TYPE/DRIVE
QUANTITY
2
2
HYDRAULIC KIT
TYPE
PUMP
HORIZONTAL MULTISTAGE END-SUCTION
MAX. WATER OPER. PRESSURE
WATER FLOW RATE
COOLING
l/s / m3/hr
0.64 / 2.3
HEATING
l/s / m3/hr
0.73 / 2.6
INSTALLATION PIPE CONNECITON
PIPING
TANK
HEAD
1000 / 145
kPa / psi
0.74 / 2.7
0.83 / 3.0
25.4 / 1
mm/in
COOLING
m
9.0
8.4
HEATING
m
6.3
5.1
MILD STEEL COATED WITH ZINC
MATERIAL
CAPACITY/VOLUME
3
40 / 1.41
L / ft
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
SCROLL
SCROLL
0 - 100%
0 - 100%
3.7 / 8.2
4.0 / 8.8
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
b) HEATING - 40°C / 45°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 7°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
74
General Data - R22 Heat pump
MODEL
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
MAC080CR
MAC100CR
Btu/h
77000
94000
W
22567
27549
Btu/h
90000
110000
W
26376
32239
COOLING
W
9577
11255
HEATING
W
9329
10759
COOLING
A
16.3
18.3
HEATING
A
15.7
POWER SOURCE
17.4
380-415 / 3 / 50
V/Ph/Hz
R22
REFRIGERANT TYPE
CONTROL
UNIT DIMENSION
PACKING DIMENSION
CAPILLARY TUBE
HEIGHT
mm/in
1245 / 49.0
WIDTH
mm/in
1500 / 59.1
DEPTH
mm/in
900 / 35.4
HEIGHT
mm/in
1452 / 57.2
WIDTH
mm/in
1732 / 68.2
DEPTH
mm/in
1032 / 40.6
UNIT WEIGHT
kg/lb
350 / 772
360 / 794
SOUND PRESSURE LEVEL
dBA
65
66
COOLING
l/s / m3/hr
1.08 / 3.9
1.31 / 4.7
HEATING
l/s / m3/hr
1.14 / 4.1
1.37 / 4.9
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
PROPELLER / DIRECT
TYPE/DRIVE
QUANTITY
2
2
HYDRAULIC KIT
HORIZONTAL MULTISTAGE END-SUCTION
TYPE
PUMP
MAX. WATER OPER. PRESSURE
WATER FLOW RATE
COOLING
l/s / m3/hr
1.08 / 3.9
HEATING
l/s / m3/hr
1.14 / 4.1
INSTALLATION PIPE CONNECITON
PIPING
TANK
HEAD
1000 / 145
kPa / psi
1.31 / 4.7
1.37 / 4.9
42 / 1 1/4"
mm/in
COOLING
m
21.8
18.3
HEATING
m
18.0
13.4
NA
MATERIAL
CAPACITY/VOLUME
3
NA
L / ft
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
SCROLL
SCROLL
0 - 50 - 100%
0 - 50 - 100%
4.3 x2 / 9.5 x2
4.5 x2 / 9.9 x2
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
b) HEATING - 40°C / 45°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 7°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
75
General Data - R22 Heat pump
MODEL
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
MAC120CR
MAC150CR
Btu/h
113000
138000
W
33118
40445
Btu/h
120000
132000
W
35169
38686
COOLING
W
11714
13881
HEATING
W
11948
14572
COOLING
A
23.7
26.3
HEATING
A
23.8
POWER SOURCE
27.3
380-415 / 3 / 50
V/Ph/Hz
R22
REFRIGERANT TYPE
CONTROL
CAPILLARY TUBE
UNIT DIMENSION
PACKING DIMENSION
HEIGHT
mm/in
WIDTH
mm/in
1800 / 70.9
DEPTH
mm/in
1150 / 45.3
HEIGHT
mm/in
1452 / 57.2
WIDTH
mm/in
2032 / 80.0
DEPTH
mm/in
1245 / 49.0
1282 / 50.5
UNIT WEIGHT
kg/lb
480 / 1058
560 / 1235
SOUND PRESSURE LEVEL
dBA
67
69
COOLING
l/s / m3/hr
1.67 / 6.0
2.00 / 7.2
HEATING
l/s / m3/hr
1.79 / 6.4
2.10 / 7.6
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
PROPELLER / DIRECT
TYPE/DRIVE
QUANTITY
2
2
HYDRAULIC KIT
HORIZONTAL MULTISTAGE END-SUCTION
TYPE
PUMP
MAX. WATER OPER. PRESSURE
WATER FLOW RATE
COOLING
l/s / m3/hr
1.67 / 6.0
HEATING
l/s / m3/hr
1.79 / 6.4
INSTALLATION PIPE CONNECITON
PIPING
TANK
HEAD
1000 / 145
kPa / psi
2.00 / 7.2
2.10 / 7.6
42 / 1 1/4"
mm/in
COOLING
m
19.7
16.5
HEATING
m
18.4
17.4
NA
MATERIAL
CAPACITY/VOLUME
3
NA
L / ft
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
SCROLL
SCROLL
0 - 50 - 100%
0 - 50 - 100%
7.6 x2 / 16.8 x2
6.5 x2 / 14.3 x2
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
b) HEATING - 40°C / 45°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 7°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
76
General Data - R407C Cooling only
MODEL
Btu/h
NOMINAL COOLING CAPACITY
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
POWER SOURCE
M4AC020C
M4AC025C
21000
23000
W
6154
6740
W
2617
2949
A
12.5
R407C
REFRIGERANT TYPE
CAPILLARY TUBE
CONTROL
UNIT DIMENSION
PACKING DIMENSION
13.6
220-240 / 1 / 50
V/Ph/Hz
HEIGHT
mm/in
800 / 31.5
WIDTH
mm/in
1160 / 45.7
DEPTH
mm/in
460 / 18.1
HEIGHT
mm/in
958 / 37.7
WIDTH
mm/in
1309 / 51.5
DEPTH
mm/in
574 / 22.6
UNIT WEIGHT
kg/lb
116 / 256
123 / 271
SOUND PRESSURE LEVEL
dBA
57
57
l/s / m3/hr
0.29 / 1.0
0.32 / 1.2
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
TYPE/DRIVE
PROPELLER / DIRECT
QUANTITY
1
1
HYDRAULIC KIT
TYPE
PUMP
PIPING
TANK
HIGH HEAD CIRCULATOR
MAX. WATER OPER. PRESSURE
kPa / psi
WATER FLOW RATE
l/s / m3/hr
INSTALLATION PIPE CONNECITON
HEAD
1000 / 145
0.29 / 1.0
m
7.8
9.6
MILD STEEL COATED WITH ZINC
MATERIAL
CAPACITY/VOLUME
0.32 / 1.2
25.4 / 1
mm/in
L / ft3
22 / 0.78
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
ROTARY
SCROLL
0 - 100%
0 - 100%
1.1 / 2.4
1.9 / 4.2
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
77
General Data - R407C Cooling only
MODEL
M4AC030C
M4AC040C
Btu/h
27000
40000
W
7912
11723
NOMINAL TOTAL INPUT POWER
W
3679
4910
NOMINAL RUNNING CURRENT
A
17.4
9.3
V/Ph/Hz
220-240 / 1 / 50
380-415 / 3 / 50
NOMINAL COOLING CAPACITY
POWER SOURCE
R407C
REFRIGERANT TYPE
CONTROL
UNIT DIMENSION
CAPILLARY TUBE
HEIGHT
mm/in
800 / 31.5
1410 / 55.5
WIDTH
mm/in
1160 / 45.7
1160 / 45.7
DEPTH
mm/in
460 / 18.1
460 / 18.1
HEIGHT
mm/in
958 / 37.7
1578 / 62.1
WIDTH
mm/in
1309 / 51.5
1309 / 51.5
DEPTH
mm/in
574 / 22.6
574 / 22.6
UNIT WEIGHT
kg/lb
128 / 282
195 / 430
SOUND PRESSURE LEVEL
dBA
58
60
l/s / m3/hr
0.38 / 1.4
0.56 / 2.0
PACKING DIMENSION
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
TYPE/DRIVE
PROPELLER / DIRECT
QUANTITY
1
2
HYDRAULIC KIT
TYPE
PUMP
PIPING
TANK
HIGH HEAD CIRCULATOR
MAX. WATER OPER. PRESSURE
kPa / psi
WATER FLOW RATE
l/s / m3/hr
INSTALLATION PIPE CONNECITON
HEAD
0.38 / 1.4
0.56 / 2.0
25.4 / 1
mm/in
m
9.8
9.7
MILD STEEL COATED WITH ZINC
MATERIAL
CAPACITY/VOLUME
HORIZONTAL MULTISTAGE END-SUCTION
1000 / 145
L / ft3
22 / 0.78
40 / 1.41
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
SCROLL
SCROLL
0 - 100%
0 - 100%
1.7 / 3.7
3.4 / 7.5
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
78
General Data - R407C Cooling only
MODEL
M4AC050C
M4AC060C
Btu/h
50000
52000
W
14654
15240
NOMINAL TOTAL INPUT POWER
W
5955
6859
NOMINAL RUNNING CURRENT
A
10.2
NOMINAL COOLING CAPACITY
POWER SOURCE
R407C
REFRIGERANT TYPE
CAPILLARY TUBE
CONTROL
UNIT DIMENSION
PACKING DIMENSION
12.9
380-415 / 3 / 50
V/Ph/Hz
HEIGHT
mm/in
1410 / 55.5
WIDTH
mm/in
1160 / 45.7
DEPTH
mm/in
460 / 18.1
HEIGHT
mm/in
1578 / 62.1
WIDTH
mm/in
1309 / 51.5
DEPTH
mm/in
574 / 22.6
UNIT WEIGHT
kg/lb
196 / 432
203 / 448
SOUND PRESSURE LEVEL
dBA
60
61
l/s / m3/hr
0.70 / 2.5
0.73 / 2.6
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
PROPELLER / DIRECT
TYPE/DRIVE
QUANTITY
2
2
HYDRAULIC KIT
HORIZONTAL MULTISTAGE END-SUCTION
TYPE
PUMP
MAX. WATER OPER. PRESSURE
WATER FLOW RATE
PIPING
TANK
INSTALLATION PIPE CONNECITON
HEAD
1000 / 145
kPa / psi
3
0.70 / 2.5
l/s / m /hr
m
7.5
8.7
MILD STEEL COATED WITH ZINC
MATERIAL
CAPACITY/VOLUME
0.73 / 2.6
25.4 / 1
mm/in
L / ft3
40 / 1.41
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
SCROLL
SCROLL
0 - 100%
0 - 100%
3.4 / 7.5
3.5 / 7.6
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
79
General Data - R407C Cooling only
MODEL
M4AC080C
M4AC100C
Btu/h
74000
88000
W
21688
25791
NOMINAL TOTAL INPUT POWER
W
9463
10771
NOMINAL RUNNING CURRENT
A
17.3
NOMINAL COOLING CAPACITY
POWER SOURCE
18.0
380-415 / 3 / 50
V/Ph/Hz
R407C
REFRIGERANT TYPE
TXV
CONTROL
UNIT DIMENSION
PACKING DIMENSION
HEIGHT
mm/in
1245 / 49.0
WIDTH
mm/in
1500 / 59.1
DEPTH
mm/in
900 / 35.4
HEIGHT
mm/in
1452 / 57.2
WIDTH
mm/in
1732 / 68.2
DEPTH
mm/in
1032 / 40.6
UNIT WEIGHT
kg/lb
340 / 750
350 / 772
SOUND PRESSURE LEVEL
dBA
65
66
l/s / m3/hr
1.08 / 3.9
1.31 / 4.7
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
PROPELLER / DIRECT
TYPE/DRIVE
QUANTITY
2
2
HYDRAULIC KIT
HORIZONTAL MULTISTAGE END-SUCTION
TYPE
PUMP
PIPING
TANK
MAX. WATER OPER. PRESSURE
kPa / psi
WATER FLOW RATE
l/s / m3/hr
INSTALLATION PIPE CONNECITON
HEAD
1000 / 145
1.08 / 3.9
m
22.6
20.0
NA
MATERIAL
CAPACITY/VOLUME
1.31 / 4.7
42 / 1 1/4"
mm/in
L / ft3
NA
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
SCROLL
SCROLL
0 - 50 - 100%
0 - 50 - 100%
4.0 x2 / 8.8 x2
3.9 x2 / 8.6 x2
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
80
General Data - R407C Cooling only
MODEL
M4AC120C
M4AC150C
Btu/h
115000
13700
W
33705
40152
NOMINAL TOTAL INPUT POWER
W
11805
14531
NOMINAL RUNNING CURRENT
A
23.6
NOMINAL COOLING CAPACITY
POWER SOURCE
27.9
380-415 / 3 / 50
V/Ph/Hz
R407C
REFRIGERANT TYPE
CONTROL
TXV
HEIGHT
UNIT DIMENSION
PACKING DIMENSION
mm/in
1245 / 49.0
WIDTH
mm/in
1800 / 70.9
DEPTH
mm/in
1150 / 45.3
HEIGHT
mm/in
1452 / 57.2
WIDTH
mm/in
2032 / 80.0
DEPTH
mm/in
UNIT WEIGHT
SOUND PRESSURE LEVEL
1282 / 50.5
kg/lb
460 / 1014
540 / 1190
dBA
67
69
l/s / m3/hr
1.67 / 6.0
2.00 / 7.2
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
PROPELLER / DIRECT
TYPE/DRIVE
QUANTITY
2
2
HYDRAULIC KIT
HORIZONTAL MULTISTAGE END-SUCTION
TYPE
PUMP
PIPING
TANK
MAX. WATER OPER. PRESSURE
kPa / psi
WATER FLOW RATE
l/s / m3/hr
INSTALLATION PIPE CONNECITON
HEAD
1000 / 145
1.67 / 6.0
m
19.4
16.7
NA
MATERIAL
CAPACITY/VOLUME
2.00 / 7.2
42 / 1 1/4"
mm/in
L / ft3
NA
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
SCROLL
SCROLL
0 - 50 - 100%
0 - 50 - 100%
5.6 x2 / 12.3 x2
6.0 x2 / 13.2 x2
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
81
General Data - R407C Heat pump
MODEL
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
M4AC020CR
M4AC025CR
Btu/h
17000
22000
W
4982
6448
Btu/h
20000
25500
W
5861
7474
COOLING
W
2597
3076
HEATING
W
2685
2745
COOLING
A
12.6
14.3
HEATING
A
13.0
POWER SOURCE
14.1
220-240 / 1 / 50
V/Ph/Hz
REFRIGERANT TYPE
R407C
CAPILLARY TUBE
CONTROL
UNIT DIMENSION
PACKING DIMENSION
HEIGHT
mm/in
800 / 31.5
WIDTH
mm/in
1160 / 45.7
DEPTH
mm/in
460 / 18.1
HEIGHT
mm/in
958 / 37.7
WIDTH
mm/in
1309 / 51.5
DEPTH
mm/in
574 / 22.6
UNIT WEIGHT
kg/lb
116 / 256
123 / 271
SOUND PRESSURE LEVEL
dBA
57
57
COOLING
l/s / m3/hr
0.24 / 0.9
0.31 / 1.1
HEATING
l/s / m3/hr
0.28 / 1.0
0.36 / 1.3
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
PROPELLER / DIRECT
TYPE/DRIVE
QUANTITY
1
1
HYDRAULIC KIT
TYPE
PUMP
HIGH HEAD CIRCULATOR
MAX. WATER OPER. PRESSURE
WATER FLOW RATE
COOLING
l/s / m3/hr
0.25 / 0.9
HEATING
l/s / m3/hr
0.31 / 1.1
INSTALLATION PIPE CONNECITON
PIPING
TANK
HEAD
1000 / 145
kPa / psi
0.32 / 1.2
0.35 / 1.3
25.4 / 1
mm/in
COOLING
m
9.7
9.8
HEATING
m
8.0
9.0
MILD STEEL COATED ZINC
MATERIAL
CAPACITY/VOLUME
3
22 / 0.78
L / ft
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
ROTARY
SCROLL
0 - 100%
0 - 100%
1.5 / 3.3
1.8 / 4.0
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
b) HEATING - 40°C / 45°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 7°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
82
General Data - R407C Heat pump
MODEL
M4AC030CR
M4AC040CR
Btu/h
25000
40000
W
7327
11723
Btu/h
32500
45000
W
9525
13188
COOLING
W
3804
4820
HEATING
W
4004
4994
COOLING
A
19.2
9.1
HEATING
A
20.0
9.2
V/Ph/Hz
220-240 / 1 / 50
380-415 / 3 / 50
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
POWER SOURCE
R407C
REFRIGERANT TYPE
CONTROL
UNIT DIMENSION
PACKING DIMENSION
CAPILLARY TUBE
HEIGHT
mm/in
800 / 31.5
1410 / 55.5
WIDTH
mm/in
1160 / 45.7
1160 / 45.7
460 / 18.1
460 / 18.1
DEPTH
mm/in
HEIGHT
mm/in
958 / 37.7
1578 / 62.1
WIDTH
mm/in
1309 / 51.5
1309 / 51.5
DEPTH
mm/in
574 / 22.6
574 / 22.6
UNIT WEIGHT
kg/lb
128 / 282
195 / 430
SOUND PRESSURE LEVEL
dBA
58
60
COOLING
l/s / m3/hr
0.35 / 1.3
0.56 / 2.0
HEATING
l/s / m3/hr
0.46 / 1.7
0.63 / 2.3
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
PROPELLER / DIRECT
TYPE/DRIVE
QUANTITY
2
2
HYDRAULIC KIT
TYPE
PUMP
HIGH HEAD CIRCULATOR
MAX. WATER OPER. PRESSURE
WATER FLOW RATE
COOLING
l/s / m3/hr
0.35 / 1.3
HEATING
l/s / m3/hr
0.46 / 1.7
INSTALLATION PIPE CONNECITON
PIPING
TANK
HEAD
HORIZONTAL MULTISTAGE END-SUCTION
1000 / 145
kPa / psi
0.56 / 2.0
0.63 / 2.3
25.4 / 1
mm/in
COOLING
m
10.2
9.7
HEATING
m
7.9
7.9
MILD STEEL COATED WITH ZINC
MATERIAL
CAPACITY/VOLUME
3
22 / 0.78
L / ft
40 / 1.41
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
ROTARY
SCROLL
0 - 100%
0 - 100%
1.6 / 3.5
3.0 / 6.6
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
b) HEATING - 40°C / 45°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 7°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
83
General Data - R407C Heat pump
MODEL
M4AC050CR
M4AC060CR
Btu/h
46000
51000
W
13481
14947
Btu/h
51000
60000
W
14947
17584
COOLING
W
5446
6507
HEATING
W
5647
6268
COOLING
A
9.5
12.7
HEATING
A
9.8
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
POWER SOURCE
12.6
380-415 / 3 / 50
V/Ph/Hz
R407C
REFRIGERANT TYPE
CONTROL
UNIT DIMENSION
PACKING DIMENSION
CAPILLARY TUBE
HEIGHT
mm/in
1410 / 55.5
WIDTH
mm/in
1160 / 45.7
DEPTH
mm/in
460 / 18.1
HEIGHT
mm/in
1578 / 62.1
WIDTH
mm/in
1309 / 51.5
DEPTH
mm/in
574 / 22.6
UNIT WEIGHT
kg/lb
196 / 432
203 / 448
SOUND PRESSURE LEVEL
dBA
60
61
COOLING
l/s / m3/hr
0.64 / 2.3
0.71 / 2.6
HEATING
l/s / m3/hr
0.71 / 2.6
0.84 / 3.0
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
PROPELLER / DIRECT
TYPE/DRIVE
QUANTITY
2
2
HYDRAULIC KIT
HORIZONTAL MULTISTAGE END-SUCTION
TYPE
PUMP
MAX. WATER OPER. PRESSURE
WATER FLOW RATE
COOLING
l/s / m3/hr
0.64 / 2.3
HEATING
l/s / m3/hr
0.71 / 2.6
INSTALLATION PIPE CONNECITON
PIPING
TANK
HEAD
1000 / 145
kPa / psi
0.71 / 2.6
0.84 / 3.0
25.4 / 1
mm/in
COOLING
m
9.0
9.1
HEATING
m
6.7
4.7
MILD STEEL COATED WITH ZINC
MATERIAL
CAPACITY/VOLUME
3
40 / 1.41
L / ft
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
SCROLL
SCROLL
0 - 100%
0 - 100%
3.5 / 7.7
4.0 / 8.8
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
b) HEATING - 40°C / 45°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 7°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
84
General Data - R407C Heat pump
MODEL
M4AC080CR
M4AC100CR
Btu/h
74000
88000
W
21688
25791
Btu/h
90000
98000
W
26377
28722
COOLING
W
9946
11028
HEATING
W
9975
11134
COOLING
A
16.4
18.5
HEATING
A
16.8
18.5
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
POWER SOURCE
380-415 / 3 / 50
V/Ph/Hz
R407C
REFRIGERANT TYPE
CONTROL
UNIT DIMENSION
PACKING DIMENSION
CAPILLARY TUBE
HEIGHT
mm/in
1245 / 49.0
WIDTH
mm/in
1500 / 59.1
DEPTH
mm/in
900 / 35.4
HEIGHT
mm/in
1452 / 57.2
WIDTH
mm/in
1732 / 68.2
DEPTH
mm/in
1032 / 40.6
UNIT WEIGHT
kg/lb
350 / 772
360 / 794
SOUND PRESSURE LEVEL
dBA
65
66
l/s / m3/hr
1.08 / 3.9
1.31 / 4.7
1.14 / 4.1
1.37 / 4.9
EVAPORATOR
NOMINAL WATER FLOW
COOLING
HEATING
3
l/s / m /hr
CONDENSER FAN
PROPELLER / DIRECT
TYPE/DRIVE
QUANTITY
2
2
HYDRAULIC KIT
HORIZONTAL MULTISTAGE END-SUCTION
TYPE
PUMP
MAX. WATER OPER. PRESSURE
WATER FLOW RATE
COOLING
l/s / m3/hr
1.08 / 3.9
HEATING
l/s / m3/hr
1.14 / 4.1
INSTALLATION PIPE CONNECITON
PIPING
TANK
HEAD
1000 / 145
kPa / psi
1.31 / 4.7
1.37 / 4.9
42 / 1 1/4"
mm/in
COOLING
m
22.5
20.0
HEATING
m
18.0
17.1
NA
MATERIAL
CAPACITY/VOLUME
L / ft3
NA
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
SCROLL
SCROLL
0 - 50 - 100%
0 - 50 - 100%
4.0 x2 / 8.8 x2
3.3 x2 / 7.3 x2
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
b) HEATING - 40°C / 45°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 7°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
85
General Data - R407C Heat pump
MODEL
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
M4AC120CR
M4AC150CR
Btu/h
110000
130000
W
32239
38101
Btu/h
118000
144000
W
34583
42204
COOLING
W
12273
15151
HEATING
W
12386
15824
COOLING
A
24.2
27.8
HEATING
A
23.8
29.0
POWER SOURCE
380-415 / 3 / 50
V/Ph/Hz
REFRIGERANT TYPE
R407C
CONTROL
UNIT DIMENSION
PACKING DIMENSION
CAPILLARY TUBE
HEIGHT
mm/in
1245 / 49.0
WIDTH
mm/in
1800 / 70.9
DEPTH
mm/in
1150 / 45.3
HEIGHT
mm/in
1452 / 57.2
WIDTH
mm/in
2032 / 80.0
DEPTH
mm/in
1282 / 50.5
UNIT WEIGHT
kg/lb
480 / 1058
560 / 1235
SOUND PRESSURE LEVEL
dBA
67
69
COOLING
l/s / m3/hr
1.67 / 6.0
2.00 / 7.2
HEATING
l/s / m3/hr
1.79 / 6.4
2.10 / 7.6
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
PROPELLER / DIRECT
TYPE/DRIVE
QUANTITY
2
2
HYDRAULIC KIT
TYPE
PUMP
HORIZONTAL MULTISTAGE END-SUCTION
MAX. WATER OPER. PRESSURE
WATER FLOW RATE
COOLING
l/s / m3/hr
1.67 / 6.0
HEATING
l/s / m3/hr
1.79 / 6.4
INSTALLATION PIPE CONNECITON
PIPING
TANK
HEAD
1000 / 145
kPa / psi
2.00 / 7.2
2.10 / 7.6
42 / 1 1/4"
mm/in
COOLING
m
20.2
17.9
HEATING
m
18.8
15.2
NA
MATERIAL
CAPACITY/VOLUME
3
NA
L / ft
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
SCROLL
SCROLL
0 - 50 - 100%
0 - 50 - 100%
5.8 x2 / 12.8 x2
6.1 x2 / 13.4 x2
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
b) HEATING - 40°C / 45°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 7°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
86
General Data - R410A Heat pump
MODEL
M5AC020CR
M5AC025CR
Btu/h
17000
21000
W
4980
6150
Btu/h
21500
25000
W
6300
7330
COOLING
W
2550
2760
HEATING
W
2590
2790
COOLING
A
11.9
12.7
HEATING
A
12.1
12.9
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
POWER SOURCE
220-240 / 1 / 50
V/Ph/Hz
R410A
REFRIGERANT TYPE
CONTROL
UNIT DIMENSION
PACKING DIMENSION
CAPILLARY TUBE
HEIGHT
mm/in
800 / 31.5
WIDTH
mm/in
1160 / 45.7
DEPTH
mm/in
460 / 18.1
HEIGHT
mm/in
958 / 37.7
WIDTH
mm/in
1309 / 51.5
DEPTH
mm/in
574 / 22.6
UNIT WEIGHT
kg/lb
125 / 276
165 / 364
SOUND PRESSURE LEVEL
dBA
57
57
l/s / m3/hr
0.23 / 0.84
0.28 / 1.00
0.32 / 1.16
0.35 / 1.25
EVAPORATOR
NOMINAL WATER FLOW
COOLING
HEATING
3
l/s / m /hr
CONDENSER FAN
PROPELLER / DIRECT
TYPE/DRIVE
QUANTITY
1
1
HYDRAULIC KIT
HIGH HEAD CIRCULATOR
TYPE
PUMP
MAX. WATER OPER. PRESSURE
WATER FLOW RATE
COOLING
l/s / m3/hr
0.23 / 0.84
0.28 / 1.00
HEATING
l/s / m3/hr
0.32 / 1.16
0.35 / 1.25
INSTALLATION PIPE CONNECITON
PIPING
TANK
HEAD
1000 / 145
kPa / psi
25.4 / 1
mm/in
COOLING
m
9.7
10.1
HEATING
m
7.3
9.1
MILD STEEL COATED WITH ZINC
MATERIAL
CAPACITY/VOLUME
L / ft3
22 / 0.78
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
ROTARY
ROTARY
0 - 100%
0 - 100%
1.2 / 2.7
1.7 / 3.8
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
b) HEATING - 40°C / 45°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 7°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
87
General Data - R410A Heat pump
MODEL
M5AC030CR
M5AC040CR
Btu/h
26800
37500
W
7848
10981
Btu/h
32500
40800
W
9517
11947
COOLING
W
3720
4330
HEATING
W
3630
4490
COOLING
A
16.7
20.3
HEATING
A
16.3
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
POWER SOURCE
21.0
380-415 / 3 / 50
V/Ph/Hz
REFRIGERANT TYPE
R410A
CONTROL
CAPILLARY TUBE & TXV
HEIGHT
mm/in
790 / 31.1
1410 / 55.5
WIDTH
mm/in
1010 / 39.8
1010 / 39.8
DEPTH
mm/in
460 / 18.1
460 / 18.1
HEIGHT
mm/in
958 / 37.7
1578 / 62.1
WIDTH
mm/in
1204 / 47.4
1204 / 47.4
DEPTH
mm/in
574 / 22.6
574 / 22.6
UNIT WEIGHT
kg/lb
125 / 276
165 / 364
SOUND PRESSURE LEVEL
dBA
58
60
COOLING
l/s / m3/hr
0.42 / 1.5
0.53 / 1.9
HEATING
l/s / m3/hr
UNIT DIMENSION
PACKING DIMENSION
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
PROPELLER / DIRECT
TYPE/DRIVE
QUANTITY
1
2
HYDRAULIC KIT
TYPE
PUMP
HIGH HEAD CIRCULATOR
MAX. WATER OPER. PRESSURE
WATER FLOW RATE
COOLING
l/s / m3/hr
HEATING
l/s / m3/hr
INSTALLATION PIPE CONNECITON
PIPING
TANK
HEAD
0.42 / 1.5
0.53 / 1.9
25.4 / 1
mm/in
COOLING
m
9.7
HEATING
m
7.9
10.6
9.4
NA
MATERIAL
CAPACITY/VOLUME
HORIZONTAL MULTISTAGE END-SUCTION
1000 / 145
kPa / psi
L / ft3
NA
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
TANDEM ROTARY
TANDEM ROTARY
0 - 50 - 100%
0 - 40 - 60 - 100%
2.2 / 4.9
3.6 / 7.8
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
b) HEATING - 40°C / 45°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 7°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
88
General Data - R410A Heat pump
MODEL
M5AC050CR
M5AC055CR
Btu/h
47000
50000
W
13763
14641
Btu/h
51000
55000
W
14934
16105
COOLING
W
5090
5890
HEATING
W
5130
5990
COOLING
A
23.0
27.3
HEATING
A
23.5
27.7
NOMINAL COOLING CAPACITY
NOMINAL HEATING CAPACITY
NOMINAL TOTAL INPUT POWER
NOMINAL RUNNING CURRENT
POWER SOURCE
380-415 / 3 / 50
V/Ph/Hz
R410A
REFRIGERANT TYPE
CONTROL
UNIT DIMENSION
PACKING DIMENSION
CAPILLARY TUBE & TXV
HEIGHT
mm/in
1410 / 55.5
WIDTH
mm/in
1010 / 39.8
DEPTH
mm/in
460 / 18.1
HEIGHT
mm/in
1578 / 62.1
WIDTH
mm/in
1204 / 47.4
DEPTH
mm/in
574 / 22.6
UNIT WEIGHT
kg/lb
167 / 368
173 / 381
SOUND PRESSURE LEVEL
dBA
60
60
COOLING
l/s / m3/hr
0.64 / 2.3
0.72 / 2.6
HEATING
l/s / m3/hr
EVAPORATOR
NOMINAL WATER FLOW
CONDENSER FAN
PROPELLER / DIRECT
TYPE/DRIVE
QUANTITY
2
2
HYDRAULIC KIT
HORIZONTAL MULTISTAGE END-SUCTION
TYPE
PUMP
MAX. WATER OPER. PRESSURE
WATER FLOW RATE
COOLING
HEATING
INSTALLATION PIPE CONNECITON
PIPING
TANK
HEAD
COOLING
HEATING
1000 / 145
kPa / psi
l/s / m3/hr
0.64 / 2.3
l/s / m /hr
25.4 / 1
mm/in
m
8.6
9.5
m
6.8
7.1
NA
MATERIAL
CAPACITY/VOLUME
0.72 / 2.6
3
3
NA
L / ft
COMPRESSOR
TYPE
STAGE OF CAPACITY CONTROL (Btu/h)
TANDEM ROTARY
TANDEM ROTARY
0 - 40 - 60 - 100%
0 - 50 - 100%
4.2 / 9.3
4.4 / 9.7
REFRIGERANT
CHARGING MASS
kg/lb
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 & ISO13253.
3) NOMINAL COOLING AND HEATING CAPACITY ARE BASED ON THE CONDITIONS BELOW :
a) COOLING - 12°C / 7°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 35°C AIR AMBIENT TEMPERATURE.
b) HEATING - 40°C / 45°C ENTERING / LEAVING EVAPORATOR WATER TEMPERATURE, 7°C AIR AMBIENT TEMPERATURE.
4) SOUND PRESSURE LEVEL ARE ACCORDING TO JIS B 8615 STANDARD. POSITION OF THE MEASUREMENT POINT IS 1m IN FRONT AND 1m BELOW THE UNIT.
89
Components Data - R22 Cooling only
MODEL
MAC020C
MAC025C
TYPE
PROPELLER
Q'TY
CONDENSER
FAN
1
1
MATERIAL
STEEL PLATE
DRIVE
DIRECT
DIAMETER
457.2 / 18
mm/in
TYPE
CONDENSER
FAN MOTOR
INDUCTION
Q'TY
INDEX OF PROTECTION (IP)
TYPE
COMPRESSOR
OIL TYPE
OIL AMOUNT
cm3 / fl.oz.
1
1
NA
NA
ROTARY
SCROLL
MINERAL OIL
MINERAL OIL
1130 / 38
1240 / 42
TYPE
CROSS FINNED TUBES
SEAMLESS COPPER
MATERIAL
TUBE
CONDENSER
COIL
PUMP
CASING
mm/in
THICKNESS
mm/in
9.52 / 3/8
0.33 / 0.013
MATERIAL
FIN
BPHE
DIAMETER
0.35 / 0.014
ALUMINIUM
THICKNESS
mm/in
FACE AREA
m2 / ft2
0.11 / 0.0043
0.66 / 7.1
0.65 / 7.0
ROW
1
2
FIN PER INCH
20
16
TYPE
BRAZED PLATE HEAT EXCHANGER
STAINLESS STEEL
MATERIAL
HIGH HEAD CIRCULATOR
TYPE
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
COLOUR
LIGHT GREY
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
90
Components Data - R22 Cooling only
MODEL
MAC030C
MAC040C
PROPELLER
TYPE
Q'TY
CONDENSER
FAN
1
2
STEEL PLATE
MATERIAL
DIRECT
DRIVE
DIAMETER
457.2 / 18
mm/in
TYPE
CONDENSER
FAN MOTOR
INDUCTION
Q'TY
INDEX OF PROTECTION (IP)
TYPE
COMPRESSOR
OIL TYPE
OIL AMOUNT
cm3 / fl.oz.
1
2
NA
NA
SCROLL
SCROLL
MINERAL OIL
MINERAL OIL
1240 / 42
1950 / 66
CROSS FINNED TUBES
TYPE
MATERIAL
TUBE
CONDENSER
COIL
PUMP
CASING
mm/in
9.52 / 3/8
THICKNESS
mm/in
0.35 / 0.014
THICKNESS
mm/in
0.11 / 0.0043
FACE AREA
m2 / ft2
ALUMINIUM
MATERIAL
FIN
BPHE
SEAMLESS COPPER
DIAMETER
0.65 / 7.0
2
2
FIN PER INCH
16
16
TYPE
BRAZED PLATE HEAT EXCHANGER
STAINLESS STEEL
MATERIAL
TYPE
1.17 / 12.6
ROW
HIGH HEAD CIRCULATOR
HORIZONTAL MULTISTAGE END-SUCTION
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
COLOUR
LIGHT GREY
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
91
Components Data - R22 Cooling only
MODEL
MAC050C
MAC060C
TYPE
PROPELLER
Q'TY
CONDENSER
FAN
2
2
STEEL PLATE
MATERIAL
DIRECT
DRIVE
DIAMETER
457.2 / 18
mm/in
TYPE
CONDENSER
FAN MOTOR
INDUCTION
Q'TY
INDEX OF PROTECTION (IP)
TYPE
COMPRESSOR
OIL TYPE
OIL AMOUNT
cm3 / fl.oz.
2
2
NA
NA
SCROLL
SCROLL
MINERAL OIL
MINERAL OIL
1770 / 60
1770 / 60
CROSS FINNED TUBES
TYPE
MATERIAL
TUBE
CONDENSER
COIL
PUMP
CASING
mm/in
THICKNESS
mm/in
9.52 / 3/8
0.35 / 0.014
MATERIAL
FIN
BPHE
SEAMLESS COPPER
DIAMETER
0.33 / 0.013
ALUMINIUM
THICKNESS
mm/in
FACE AREA
m2 / ft2
0.11 / 0.0043
1.17 / 12.6
1.17 / 12.6
ROW
2
2
FIN PER INCH
16
16
BRAZED PLATE HEAT EXCHANGER
TYPE
MATERIAL
STAINLESS STEEL
HORIZONTAL MULTISTAGE END-SUCTION
TYPE
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
COLOUR
LIGHT GREY
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
92
Components Data - R22 Cooling only
MODEL
MAC080C
MAC100C
PROPELLER
TYPE
Q'TY
CONDENSER
FAN
2
2
ALUMINIUM
MATERIAL
DIRECT
DRIVE
DIAMETER
609.6 / 24
mm/in
TYPE
CONDENSER
FAN MOTOR
INDUCTION
Q'TY
INDEX OF PROTECTION (IP)
TYPE
COMPRESSOR
OIL TYPE
OIL
AMOUNT
2
2
NA
NA
SCROLL
SCROLL
MINERAL OIL
MINERAL OIL
1770 / 60
COMP1
cm3 / fl.oz.
1950 / 66
COMP2
cm3 / fl.oz.
1950 / 66
SEAMLESS COPPER
MATERIAL
TUBE
CONDENSER
COIL
BPHE
PUMP
CASING
DIAMETER
mm/in
9.52 / 3/8
THICKNESS
mm/in
0.33 / 0.013
ALUMINIUM (HYDROPHILIC)
MATERIAL
FIN
1770 / 60
CROSS FINNED TUBES
TYPE
THICKNESS
mm/in
FACE AREA
m2 / ft2
0.11 / 0.0043
1.37 / 14.7
1.37 / 14.7
ROW
2
2
FIN PER INCH
14
14
BRAZED PLATE HEAT EXCHANGER
TYPE
STAINLESS STEEL
MATERIAL
TYPE
HORIZONTAL MULTISTAGE END-SUCTION
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
LIGHT GREY
COLOUR
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
93
Components Data - R22 Cooling only
MODEL
MAC120C
MAC150C
TYPE
PROPELLER
Q'TY
CONDENSER
FAN
2
2
ALUMINIUM
MATERIAL
DIRECT
DRIVE
DIAMETER
609.6 / 24
mm/in
INDUCTION
TYPE
CONDENSER
FAN MOTOR
Q'TY
INDEX OF PROTECTION (IP)
TYPE
COMPRESSOR
OIL TYPE
OIL
AMOUNT
2
2
NA
NA
SCROLL
SCROLL
MINERAL OIL
MINERAL OIL
2510 / 85
COMP1
cm3 / fl.oz.
1770 / 60
COMP2
cm3 / fl.oz.
1770 / 60
TYPE
MATERIAL
TUBE
CONDENSER
COIL
BPHE
PUMP
CASING
SEAMLESS COPPER
DIAMETER
mm/in
9.52 / 3/8
THICKNESS
mm/in
0.33 / 0.013
MATERIAL
FIN
2510 / 85
CROSS FINNED TUBES
ALUMINIUM (HYDROPHILIC)
THICKNESS
mm/in
FACE AREA
m2 / ft2
0.11 / 0.0043
1.79 / 19.3
1.79 / 19.3
ROW
2
2
FIN PER INCH
14
14
TYPE
BRAZED PLATE HEAT EXCHANGER
STAINLESS STEEL
MATERIAL
HORIZONTAL MULTISTAGE END-SUCTION
TYPE
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
COLOUR
LIGHT GREY
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
94
Components Data - R22 Heat pump
MODEL
MAC020CR
MAC025CR
PROPELLER
TYPE
Q'TY
CONDENSER
FAN
1
1
STEEL PLATE
MATERIAL
DIRECT
DRIVE
DIAMETER
457.2 / 18
mm/in
INDUCTION
TYPE
CONDENSER
FAN MOTOR
Q'TY
INDEX OF PROTECTION (IP)
TYPE
COMPRESSOR
OIL TYPE
OIL AMOUNT
cm3 / fl.oz.
1
1
NA
NA
ROTARY
SCROLL
MINERAL OIL
MINERAL OIL
1130 / 38
1240 / 42
CROSS FINNED TUBES
TYPE
SEAMLESS COPPER
MATERIAL
TUBE
CONDENSER
COIL
PUMP
CASING
mm/in
THICKNESS
mm/in
9.52 / 3/8
0.33 / 0.013
0.35 / 0.014
ALUMINIUM (HYDROPHILIC GOLD)
MATERIAL
FIN
BPHE
DIAMETER
THICKNESS
mm/in
FACE AREA
m2 / ft2
0.11 / 0.0043
0.66 / 7.1
0.65 / 7.0
ROW
1
2
FIN PER INCH
20
16
TYPE
BRAZED PLATE HEAT EXCHANGER
STAINLESS STEEL
MATERIAL
HIGH HEAD CIRCULATOR
TYPE
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
COLOUR
LIGHT GREY
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
95
Components Data - R22 Heat pump
MODEL
MAC030CR
MAC040CR
TYPE
PROPELLER
Q'TY
CONDENSER
FAN
1
2
MATERIAL
STEEL PLATE
DRIVE
DIRECT
DIAMETER
457.2 / 18
mm/in
TYPE
CONDENSER
FAN MOTOR
INDUCTION
Q'TY
INDEX OF PROTECTION (IP)
TYPE
COMPRESSOR
OIL TYPE
OIL AMOUNT
cm3 / fl.oz.
1
2
NA
NA
SCROLL
SCROLL
MINERAL OIL
MINERAL OIL
1240 / 42
1950 / 66
TYPE
CROSS FINNED TUBES
SEAMLESS COPPER
MATERIAL
TUBE
CONDENSER
COIL
PUMP
CASING
mm/in
9.52 / 3/8
THICKNESS
mm/in
0.35 / 0.014
THICKNESS
mm/in
0.11 / 0.0043
FACE AREA
m2 / ft2
MATERIAL
FIN
BPHE
DIAMETER
ALUMINIUM
0.65 / 7.0
2
2
FIN PER INCH
16
16
TYPE
BRAZED PLATE HEAT EXCHANGER
STAINLESS STEEL
MATERIAL
TYPE
1.17 / 12.6
ROW
HIGH HEAD CIRCULATOR
HORIZONTAL MULTISTAGE END-SUCTION
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
COLOUR
LIGHT GREY
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
96
Components Data - R22 Heat pump
MODEL
MAC050CR
MAC060CR
PROPELLER
TYPE
Q'TY
CONDENSER
FAN
2
2
STEEL PLATE
MATERIAL
DIRECT
DRIVE
DIAMETER
457.2 / 18
mm/in
INDUCTION
TYPE
CONDENSER
FAN MOTOR
Q'TY
INDEX OF PROTECTION (IP)
TYPE
COMPRESSOR
OIL TYPE
OIL AMOUNT
cm3 / fl.oz.
2
2
NA
NA
SCROLL
SCROLL
MINERAL OIL
MINERAL OIL
1770 / 60
1770 / 60
CROSS FINNED TUBES
TYPE
SEAMLESS COPPER
MATERIAL
TUBE
CONDENSER
COIL
PUMP
CASING
mm/in
THICKNESS
mm/in
9.52 / 3/8
0.35 / 0.014
0.33 / 0.013
ALUMINIUM (HYDROPHILIC GOLD)
MATERIAL
FIN
BPHE
DIAMETER
THICKNESS
mm/in
FACE AREA
m2 / ft2
0.11 / 0.0043
1.17 / 12.6
1.17 / 12.6
ROW
2
2
FIN PER INCH
16
16
TYPE
BRAZED PLATE HEAT EXCHANGER
STAINLESS STEEL
MATERIAL
TYPE
HORIZONTAL MULTISTAGE END-SUCTION
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
COLOUR
LIGHT GREY
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
97
Components Data - R22 Heat pump
MODEL
MAC080CR
MAC100CR
TYPE
PROPELLER
Q'TY
CONDENSER
FAN
2
2
MATERIAL
ALUMINIUM
DRIVE
DIRECT
DIAMETER
609.6 / 24
mm/in
INDUCTION
TYPE
CONDENSER
FAN MOTOR
Q'TY
INDEX OF PROTECTION (IP)
TYPE
COMPRESSOR
OIL TYPE
OIL
AMOUNT
2
2
NA
NA
SCROLL
SCROLL
MINERAL OIL
MINERAL OIL
1770 / 60
COMP1
cm3 / fl.oz.
1950 / 66
COMP2
cm3 / fl.oz.
1950 / 66
SEAMLESS COPPER
MATERIAL
TUBE
CONDENSER
COIL
DIAMETER
mm/in
9.52 / 3/8
THICKNESS
mm/in
0.33 / 0.013
MATERIAL
THICKNESS
FIN
BPHE
PUMP
CASING
1770 / 60
CROSS FINNED TUBES
TYPE
FACE AREA
ALUMINIUM (HYDROPHILIC)
0.11 / 0.0043
mm/in
2
2
1.37 / 14.7
m / ft
1.37 / 14.7
ROW
2
2
FIN PER INCH
14
14
BRAZED PLATE HEAT EXCHANGER
TYPE
STAINLESS STEEL
MATERIAL
TYPE
HORIZONTAL MULTISTAGE END-SUCTION
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
LIGHT GREY
COLOUR
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
98
Components Data - R22 Heat pump
MODEL
MAC120CR
MAC150CR
PROPELLER
TYPE
Q'TY
CONDENSER
FAN
2
2
ALUMINIUM
MATERIAL
DIRECT
DRIVE
DIAMETER
609.6 / 24
mm/in
TYPE
CONDENSER
FAN MOTOR
INDUCTION
Q'TY
INDEX OF PROTECTION (IP)
TYPE
COMPRESSOR
OIL TYPE
OIL
AMOUNT
2
2
NA
NA
SCROLL
SCROLL
MINERAL OIL
MINERAL OIL
2510 / 85
COMP1
cm3 / fl.oz.
1770 / 60
COMP2
cm3 / fl.oz.
1770 / 60
SEAMLESS COPPER
MATERIAL
TUBE
CONDENSER
COIL
BPHE
PUMP
CASING
DIAMETER
mm/in
9.52 / 3/8
THICKNESS
mm/in
0.33 / 0.013
ALUMINIUM (HYDROPHILIC)
MATERIAL
FIN
2510 / 85
CROSS FINNED TUBES
TYPE
THICKNESS
mm/in
FACE AREA
m2 / ft2
0.11 / 0.0043
1.79 / 19.3
1.79 / 19.3
ROW
2
2
FIN PER INCH
14
14
BRAZED PLATE HEAT EXCHANGER
TYPE
STAINLESS STEEL
MATERIAL
TYPE
HORIZONTAL MULTISTAGE END-SUCTION
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
LIGHT GREY
COLOUR
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
99
Components Data - R407C Cooling only
MODEL
M4AC020C
PROPELLER
TYPE
Q'TY
CONDENSER
FAN
M4AC025C
1
1
STEEL PLATE
MATERIAL
DIRECT
DRIVE
DIAMETER
457.2 / 18
mm/in
INDUCTION
TYPE
CONDENSER
FAN MOTOR
Q'TY
INDEX OF PROTECTION (IP)
COMPRESSOR
1
1
NA
NA
TYPE
ROTARY
SCROLL
OIL TYPE
POE OIL
POE OIL
OIL AMOUNT
cm3 / fl.oz.
700 / 24
1240 / 42
CROSS FINNED TUBES
TYPE
SEAMLESS COPPER
MATERIAL
TUBE
CONDENSER
COIL
PUMP
CASING
mm/in
THICKNESS
mm/in
9.52 / 3/8
0.33 / 0.013
0.35 / 0.014
ALUMINIUM
MATERIAL
FIN
BPHE
DIAMETER
THICKNESS
mm/in
FACE AREA
m2 / ft2
0.11 / 0.0043
0.66 / 7.1
0.65 / 7.0
ROW
1
2
FIN PER INCH
20
16
TYPE
BRAZED PLATE HEAT EXCHANGER
STAINLESS STEEL
MATERIAL
TYPE
HIGH HEAD CIRCULATOR
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
COLOUR
LIGHT GREY
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
100
Components Data - R407C Cooling only
MODEL
M4AC030C
PROPELLER
TYPE
Q'TY
CONDENSER
FAN
M4AC040C
1
2
STEEL PLATE
MATERIAL
DIRECT
DRIVE
DIAMETER
457.2 / 18
mm/in
INDUCTION
TYPE
CONDENSER
FAN MOTOR
Q'TY
INDEX OF PROTECTION (IP)
COMPRESSOR
1
2
NA
NA
TYPE
SCROLL
SCROLL
OIL TYPE
POE OIL
POE OIL
OIL AMOUNT
cm3 / fl.oz.
1240 / 42
SEAMLESS COPPER
MATERIAL
TUBE
CONDENSER
COIL
BPHE
PUMP
CASING
DIAMETER
mm/in
9.52 / 3/8
THICKNESS
mm/in
0.35 / 0.014
THICKNESS
mm/in
0.11 / 0.0043
FACE AREA
m2 / ft2
ALUMINIUM
MATERIAL
FIN
0.65 / 7.0
1.17 / 12.6
ROW
2
2
FIN PER INCH
16
16
TYPE
BRAZED PLATE HEAT EXCHANGER
STAINLESS STEEL
MATERIAL
TYPE
1950 / 66
CROSS FINNED TUBES
TYPE
HIGH HEAD CIRCULATOR
HORIZONTAL MULTISTAGE END-SUCTION
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
COLOUR
LIGHT GREY
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
101
Components Data - R407C Cooling only
MODEL
M4AC050C
Q'TY
CONDENSER
FAN
M4AC060C
PROPELLER
TYPE
2
2
MATERIAL
STEEL PLATE
DIRECT
DRIVE
DIAMETER
457.2 / 18
mm/in
INDUCTION
TYPE
CONDENSER
FAN MOTOR
Q'TY
INDEX OF PROTECTION (IP)
COMPRESSOR
2
2
NA
NA
TYPE
SCROLL
SCROLL
OIL TYPE
POE OIL
POE OIL
OIL AMOUNT
cm3 / fl.oz.
1770 / 60
SEAMLESS COPPER
MATERIAL
TUBE
CONDENSER
COIL
DIAMETER
mm/in
THICKNESS
mm/in
THICKNESS
BPHE
PUMP
CASING
9.52 / 3/8
0.35 / 0.014
FACE AREA
0.33 / 0.013
ALUMINIUM
MATERIAL
FIN
1770 / 60
CROSS FINNED TUBES
TYPE
0.11 / 0.0043
mm/in
2
2
1.17 / 12.6
m / ft
1.17 / 12.6
ROW
2
2
FIN PER INCH
16
16
TYPE
BRAZED PLATE HEAT EXCHANGER
STAINLESS STEEL
MATERIAL
HORIZONTAL MULTISTAGE END-SUCTION
TYPE
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
COLOUR
LIGHT GREY
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
102
Components Data - R407C Cooling only
MODEL
M4AC080C
Q'TY
CONDENSER
FAN
M4AC100C
PROPELLER
TYPE
2
2
ALUMINIUM
MATERIAL
DIRECT
DRIVE
DIAMETER
609.6 / 24
mm/in
TYPE
CONDENSER
FAN MOTOR
INDUCTION
Q'TY
INDEX OF PROTECTION (IP)
COMPRESSOR
2
2
NA
NA
TYPE
SCROLL
SCROLL
OIL TYPE
POE OIL
POE OIL
1770 / 60
OIL
AMOUNT
COMP1
cm3 / fl.oz.
1950 / 66
COMP2
cm3 / fl.oz.
1950 / 66
TYPE
MATERIAL
TUBE
CONDENSER
COIL
mm/in
9.52 / 3/8
THICKNESS
mm/in
0.33 / 0.013
THICKNESS
BPHE
PUMP
CASING
SEAMLESS COPPER
DIAMETER
ALUMINIUM (HYDROPHILIC)
MATERIAL
FIN
1770 / 60
CROSS FINNED TUBES
FACE AREA
0.11 / 0.0043
mm/in
2
2
1.37 / 14.7
m / ft
1.37 / 14.7
ROW
2
2
FIN PER INCH
14
14
BRAZED PLATE HEAT EXCHANGER
TYPE
MATERIAL
STAINLESS STEEL
HORIZONTAL MULTISTAGE END-SUCTION
TYPE
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
LIGHT GREY
COLOUR
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
103
Components Data - R407C Cooling only
MODEL
M4AC120C
PROPELLER
TYPE
Q'TY
CONDENSER
FAN
M4AC150C
2
2
ALUMINIUM
MATERIAL
DIRECT
DRIVE
DIAMETER
609.6 / 24
mm/in
TYPE
CONDENSER
FAN MOTOR
INDUCTION
Q'TY
INDEX OF PROTECTION (IP)
COMPRESSOR
2
2
NA
NA
TYPE
SCROLL
SCROLL
OIL TYPE
POE OIL
POE OIL
2510 / 85
OIL
AMOUNT
COMP1
cm3 / fl.oz.
1770 / 60
COMP2
cm3 / fl.oz.
1770 / 60
SEAMLESS COPPER
MATERIAL
TUBE
CONDENSER
COIL
BPHE
PUMP
CASING
DIAMETER
mm/in
9.52 / 3/8
THICKNESS
mm/in
0.33 / 0.013
ALUMINIUM (HYDROPHILIC)
MATERIAL
FIN
2510 / 85
CROSS FINNED TUBES
TYPE
THICKNESS
mm/in
FACE AREA
m2 / ft2
0.11 / 0.0043
1.79 / 19.3
1.79 / 19.3
ROW
2
2
FIN PER INCH
14
14
BRAZED PLATE HEAT EXCHANGER
TYPE
STAINLESS STEEL
MATERIAL
TYPE
HORIZONTAL MULTISTAGE END-SUCTION
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
LIGHT GREY
COLOUR
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
104
Components Data - R407C Heat pump
MODEL
M4AC020CR
TYPE
PROPELLER
Q'TY
CONDENSER
FAN
M4AC025CR
1
1
STEEL PLATE
MATERIAL
DIRECT
DRIVE
DIAMETER
457.2 / 18
mm/in
TYPE
CONDENSER
FAN MOTOR
INDUCTION
Q'TY
INDEX OF PROTECTION (IP)
COMPRESSOR
1
1
NA
NA
TYPE
ROTARY
SCROLL
OIL TYPE
POE OIL
POE OIL
OIL AMOUNT
cm3 / fl.oz.
700 / 24
1240 / 42
TYPE
CROSS FINNED TUBES
MATERIAL
TUBE
CONDENSER
COIL
PUMP
CASING
mm/in
THICKNESS
mm/in
9.52 / 3/8
0.33 / 0.013
MATERIAL
FIN
BPHE
SEAMLESS COPPER
DIAMETER
0.35 / 0.014
ALUMINIUM (HYDROPHILIC GOLD)
THICKNESS
mm/in
FACE AREA
m2 / ft2
0.11 / 0.0043
0.66 / 7.1
0.65 / 7.0
ROW
1
2
FIN PER INCH
20
16
TYPE
BRAZED PLATE HEAT EXCHANGER
MATERIAL
STAINLESS STEEL
TYPE
HIGH HEAD CIRCULATOR
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
COLOUR
LIGHT GREY
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
105
Components Data - R407C Heat pump
MODEL
M4AC030CR
PROPELLER
TYPE
Q'TY
CONDENSER
FAN
M4AC040CR
1
2
STEEL PLATE
MATERIAL
DIRECT
DRIVE
DIAMETER
457.2 / 18
mm/in
INDUCTION
TYPE
CONDENSER
FAN MOTOR
Q'TY
INDEX OF PROTECTION (IP)
COMPRESSOR
1
2
NA
NA
TYPE
SCROLL
SCROLL
OIL TYPE
POE OIL
POE OIL
OIL AMOUNT
cm3 / fl.oz.
1240 / 42
SEAMLESS COPPER
MATERIAL
TUBE
CONDENSER
COIL
BPHE
PUMP
CASING
DIAMETER
mm/in
9.52 / 3/8
THICKNESS
mm/in
0.35 / 0.014
ALUMINIUM (HYDROPHILIC GOLD)
MATERIAL
FIN
THICKNESS
mm/in
FACE AREA
m2 / ft2
0.11 / 0.0043
0.65 / 7.0
1.17 / 12.6
ROW
2
2
FIN PER INCH
16
16
TYPE
BRAZED PLATE HEAT EXCHANGER
STAINLESS STEEL
MATERIAL
TYPE
1950 / 66
CROSS FINNED TUBES
TYPE
HIGH HEAD CIRCULATOR
HORIZONTAL MULTISTAGE END-SUCTION
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
COLOUR
LIGHT GREY
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
106
Components Data - R407C Heat pump
MODEL
M4AC050CR
TYPE
PROPELLER
Q'TY
CONDENSER
FAN
M4AC060CR
2
2
STEEL PLATE
MATERIAL
DIRECT
DRIVE
DIAMETER
457.2 / 18
mm/in
TYPE
CONDENSER
FAN MOTOR
INDUCTION
Q'TY
INDEX OF PROTECTION (IP)
COMPRESSOR
2
2
NA
NA
TYPE
SCROLL
SCROLL
OIL TYPE
POE OIL
POE OIL
OIL AMOUNT
cm3 / fl.oz.
1770 / 60
MATERIAL
TUBE
CONDENSER
COIL
BPHE
PUMP
CASING
SEAMLESS COPPER
DIAMETER
mm/in
THICKNESS
mm/in
9.52 / 3/8
0.35 / 0.014
MATERIAL
FIN
1770 / 60
CROSS FINNED TUBES
TYPE
0.33 / 0.013
ALUMINIUM (HYDROPHILIC GOLD)
THICKNESS
mm/in
FACE AREA
m2 / ft2
0.11 / 0.0043
1.17 / 12.6
1.17 / 12.6
ROW
2
2
FIN PER INCH
16
16
TYPE
BRAZED PLATE HEAT EXCHANGER
MATERIAL
STAINLESS STEEL
HORIZONTAL MULTISTAGE END-SUCTION
TYPE
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
COLOUR
LIGHT GREY
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
107
Components Data - R407C Heat pump
MODEL
M4AC080CR
Q'TY
CONDENSER
FAN
M4AC100CR
PROPELLER
TYPE
2
2
ALUMINIUM
MATERIAL
DIRECT
DRIVE
DIAMETER
609.6 / 24
mm/in
TYPE
CONDENSER
FAN MOTOR
INDUCTION
Q'TY
INDEX OF PROTECTION (IP)
COMPRESSOR
2
2
NA
NA
TYPE
SCROLL
SCROLL
OIL TYPE
POE OIL
POE OIL
1770 / 60
OIL
AMOUNT
COMP1
cm3 / fl.oz.
1950 / 66
COMP2
cm3 / fl.oz.
1950 / 66
SEAMLESS COPPER
MATERIAL
TUBE
CONDENSER
COIL
BPHE
PUMP
CASING
DIAMETER
mm/in
9.52 / 3/8
THICKNESS
mm/in
0.33 / 0.013
ALUMINIUM (HYDROPHILIC)
MATERIAL
FIN
1770 / 60
CROSS FINNED TUBES
TYPE
THICKNESS
mm/in
FACE AREA
m2 / ft2
0.11 / 0.0043
1.37 / 14.7
1.37 / 14.7
ROW
2
2
FIN PER INCH
14
14
BRAZED PLATE HEAT EXCHANGER
TYPE
STAINLESS STEEL
MATERIAL
TYPE
HORIZONTAL MULTISTAGE END-SUCTION
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
LIGHT GREY
COLOUR
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
108
Components Data - R407C Heat pump
MODEL
M4AC120CR
TYPE
Q'TY
CONDENSER
FAN
M4AC150CR
PROPELLER
2
2
MATERIAL
ALUMINIUM
DRIVE
DIRECT
DIAMETER
609.6 / 24
mm/in
INDUCTION
TYPE
CONDENSER
FAN MOTOR
Q'TY
INDEX OF PROTECTION (IP)
COMPRESSOR
2
2
NA
NA
TYPE
SCROLL
SCROLL
OIL TYPE
POE OIL
POE OIL
2510 / 85
OIL
AMOUNT
COMP1
cm3 / fl.oz.
1770 / 60
COMP2
cm3 / fl.oz.
1770 / 60
SEAMLESS COPPER
MATERIAL
TUBE
CONDENSER
COIL
BPHE
PUMP
CASING
DIAMETER
mm/in
9.52 / 3/8
THICKNESS
mm/in
0.33 / 0.013
MATERIAL
FIN
2510 / 85
CROSS FINNED TUBES
TYPE
ALUMINIUM (HYDROPHILIC GOLD)
THICKNESS
mm/in
FACE AREA
m2 / ft2
0.11 / 0.0043
1.79 / 19.3
1.79 / 19.3
ROW
2
2
FIN PER INCH
14
14
BRAZED PLATE HEAT EXCHANGER
TYPE
STAINLESS STEEL
MATERIAL
TYPE
HORIZONTAL MULTISTAGE END-SUCTION
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
LIGHT GREY
COLOUR
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
109
Components Data - R410A Heat pump
MODEL
M5AC020CR
Q'TY
CONDENSER
FAN
M5AC025CR
PROPELLER
TYPE
1
1
MATERIAL
STEEL PLATE
DIRECT
DRIVE
DIAMETER
457.2 / 18
mm/in
TYPE
CONDENSER
FAN MOTOR
INDUCTION
Q'TY
INDEX OF PROTECTION (IP)
COMPRESSOR
1
1
NA
NA
TYPE
SCROLL
SCROLL
OIL TYPE
POE OIL
POE OIL
OIL AMOUNT
cm3 / fl.oz.
1130 / 38
SEAMLESS COPPER
MATERIAL
TUBE
CONDENSER
COIL
BPHE
PUMP
CASING
DIAMETER
mm/in
9.52 / 3/8
THICKNESS
mm/in
0.37 / 0..015
MATERIAL
FIN
1130 / 38
CROSS FINNED TUBES
TYPE
ALUMINIUM (HYDROPHILIC GOLD)
THICKNESS
mm/in
FACE AREA
m2 / ft2
0.11 / 0.0043
0.66 / 7.1
0.65 / 7.0
ROW
1
2
FIN PER INCH
20
16
TYPE
BRAZED PLATE HEAT EXCHANGER
STAINLESS STEEL
MATERIAL
HIGH HEAD CIRCULATOR
TYPE
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
COLOUR
LIGHT GREY
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
110
Components Data - R410A Heat pump
MODEL
M5AC030CR
TYPE
Q'TY
CONDENSER
FAN
M5AC040CR
PROPELLER
1
2
MATERIAL
STEEL PLATE
DRIVE
DIRECT
DIAMETER
457.2 / 18
mm/in
INDUCTION
TYPE
CONDENSER
FAN MOTOR
Q'TY
INDEX OF PROTECTION (IP)
COMPRESSOR
1
2
NA
NA
TYPE
SCROLL
SCROLL
OIL TYPE
POE OIL
POE OIL
OIL
AMOUNT
COMP1
cm3 / fl.oz.
670 / 23
670 / 23
COMP2
cm3 / fl.oz.
670 / 23
1130 / 38
CROSS FINNED TUBES
TYPE
SEAMLESS COPPER
MATERIAL
TUBE
CONDENSER
COIL
PUMP
CASING
mm/in
9.52 / 3/8
THICKNESS
mm/in
0.37 / 0.015
MATERIAL
FIN
BPHE
DIAMETER
ALUMINIUM (HYDROPHILIC GOLD)
THICKNESS
mm/in
FACE AREA
m2 / ft2
0.11 / 0.0043
0.65 / 7.0
1.17 / 12.6
ROW
2
2
FIN PER INCH
16
16
BRAZED PLATE HEAT EXCHANGER
TYPE
STAINLESS STEEL
MATERIAL
TYPE
HORIZONTAL MULTISTAGE END-SUCTION
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
LIGHT GREY
COLOUR
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
111
Components Data - R410A Heat pump
MODEL
M5AC050CR
PROPELLER
TYPE
Q'TY
CONDENSER
FAN
M5AC055CR
2
2
STEEL PLATE
MATERIAL
DIRECT
DRIVE
DIAMETER
457.2 / 18
mm/in
TYPE
CONDENSER
FAN MOTOR
INDUCTION
Q'TY
INDEX OF PROTECTION (IP)
COMPRESSOR
2
2
NA
NA
TYPE
SCROLL
SCROLL
OIL TYPE
POE OIL
POE OIL
1130 / 38
OIL
AMOUNT
COMP1
cm3 / fl.oz.
1130 / 38
COMP2
cm3 / fl.oz.
1130 / 38
SEAMLESS COPPER
MATERIAL
TUBE
CONDENSER
COIL
BPHE
PUMP
CASING
DIAMETER
mm/in
9.52 / 3/8
THICKNESS
mm/in
0.37 / 0.015
ALUMINIUM (HYDROPHILIC GOLD)
MATERIAL
FIN
1130 / 38
CROSS FINNED TUBES
TYPE
THICKNESS
mm/in
FACE AREA
m2 / ft2
0.11 / 0.0043
1.17 / 12.6
1.17 / 12.6
ROW
2
2
FIN PER INCH
16
16
BRAZED PLATE HEAT EXCHANGER
TYPE
STAINLESS STEEL
MATERIAL
TYPE
HORIZONTAL MULTISTAGE END-SUCTION
MATERIAL
CAST IRON & STAINLESS STEEL
MATERIAL
ELECTRO-GALVANIZED MILD STEEL
FINISH
POLYESTER POWDER
LIGHT GREY
COLOUR
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
112
Safety Devices - R22 Cooling only & Heat pump
MODEL
MAC020C/CR
TYPE
HIGH PRESSURE
SWITCH
NC
NC
OPEN
kPa / psi
2939 / 426
2939 / 426
CLOSE
kPa / psi
2415 / 350
2415 / 350
TYPE
LOW PRESSURE
SWITCH (COOLING OPEN
ONLY)
CLOSE
LOW PRESSURE
SAFETY DEVICE SWITCH (HEAT
PUMP)
MAC025C/CR
NC
NC
kPa / psi
124 / 18
125 / 18
kPa / psi
193 / 28
193 / 28
TYPE
NC
NC
OPEN
kPa / psi
48 / 7
48 / 7
CLOSE
kPa / psi
152 / 22
152 / 22
DIFFERENTIAL PRESSURE SWITCH
YES
YES
ANTI-FREEZE PROTECTION SENSOR
YES
YES
OVER PRESSURE RELIEF VALVE
YES
YES
ANTI-FREEZE HEATER ON BPHE
YES
YES
PUMP OLP
YES
YES
COMPRESSOR OLP
YES
YES
MAC030C/CR
MAC040C/CR
MODEL
HIGH PRESSURE
SWITCH
TYPE
OPEN
CLOSE
LOW PRESSURE TYPE
SWITCH (COOLING OPEN
ONLY)
CLOSE
LOW PRESSURE TYPE
NC
NC
kPa / psi
2939 / 426
2939 / 426
kPa / psi
2415 / 350
2415 / 350
NC
NC
kPa / psi
124 / 18
125 / 18
kPa / psi
193 / 28
193 / 28
NC
NC
kPa / psi
48 / 7
48 / 7
kPa / psi
152 / 22
152 / 22
NA
BUILT IN ON BOARD
DIFFERENTIAL PRESSURE SWITCH
YES
YES
ANTI-FREEZE PROTECTION SENSOR
YES
YES
NA
110 / 230
OVER PRESSURE RELIEF VALVE
YES
YES
ANTI-FREEZE HEATER ON BPHE
PUMP OLP
YES
YES
YES
YES
COMPRESSOR OLP
YES
YES
MAC050C/CR
MAC060C/CR
SWITCH (HEAT
SAFETY DEVICE PUMP)
OPEN
CLOSE
PHASE PROTECTION
DISCH. THERMOSTAT SETTING
°C / °F
MODEL
HIGH PRESSURE
SWITCH
TYPE
OPEN
CLOSE
LOW PRESSURE TYPE
SWITCH (COOLING OPEN
ONLY)
CLOSE
LOW PRESSURE TYPE
SWITCH (HEAT
SAFETY DEVICE PUMP)
OPEN
CLOSE
PHASE PROTECTION
NC
NC
kPa / psi
2939 / 426
2939 / 426
kPa / psi
2415 / 350
2415 / 350
NC
NC
kPa / psi
124 / 18
125 / 18
kPa / psi
193 / 28
193 / 28
kPa / psi
NC
48 / 7
48 / 7
152 / 22
152 / 22
BUILT IN ON BOARD
BUILT IN ON BOARD
DIFFERENTIAL PRESSURE SWITCH
YES
YES
ANTI-FREEZE PROTECTION SENSOR
YES
YES
110 / 230
110 / 230
OVER PRESSURE RELIEF VALVE
YES
YES
ANTI-FREEZE HEATER ON BPHE
PUMP OLP
YES
YES
YES
YES
COMPRESSOR OLP
YES
YES
DISCH. THERMOSTAT SETTING
kPa / psi
NC
°C / °F
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
113
Safety Devices - R22 Cooling only & Heat pump
MODEL
MAC080C/CR
TYPE
HIGH PRESSURE
SWITCH
NC
NC
OPEN
kPa / psi
2939 / 426
2939 / 426
CLOSE
kPa / psi
2415 / 350
2415 / 350
LOW PRESSURE TYPE
SWITCH (COOLING OPEN
ONLY)
CLOSE
SAFETY DEVICE
LOW PRESSURE
SWITCH (HEAT
PUMP)
NC
NC
kPa / psi
124 / 18
125 / 18
kPa / psi
193 / 28
193 / 28
TYPE
OPEN
kPa / psi
CLOSE
kPa / psi
NC
NC
48 / 7
48 / 7
152 / 22
152 / 22
BUILT IN ON BOARD
BUILT IN ON BOARD
DIFFERENTIAL PRESSURE SWITCH
YES
YES
ANTI-FREEZE PROTECTION SENSOR
YES
PHASE PROTECTION
DISCH. THERMOSTAT SETTING
°C / °F
110 / 230
YES
110 / 230
OVER PRESSURE RELIEF VALVE
YES
YES
ANTI-FREEZE HEATER ON BPHE
YES
YES
PUMP OLP
YES
YES
COMPRESSOR OLP
YES
YES
MAC120C/CR
MAC150C/CR
MODEL
HIGH PRESSURE
SWITCH
TYPE
OPEN
CLOSE
LOW PRESSURE TYPE
SWITCH (COOLING OPEN
ONLY)
CLOSE
LOW PRESSURE TYPE
SAFETY DEVICE
MAC100C/CR
SWITCH (HEAT
PUMP)
OPEN
CLOSE
PHASE PROTECTION
NC
NC
kPa / psi
2939 / 426
2939 / 426
kPa / psi
2415 / 350
2415 / 350
NC
NC
kPa / psi
124 / 18
125 / 18
kPa / psi
193 / 28
193 / 28
kPa / psi
NC
48 / 7
48 / 7
152 / 22
152 / 22
BUILT IN ON BOARD
BUILT IN ON BOARD
DIFFERENTIAL PRESSURE SWITCH
YES
YES
ANTI-FREEZE PROTECTION SENSOR
YES
YES
110 / 230
110 / 230
OVER PRESSURE RELIEF VALVE
YES
YES
ANTI-FREEZE HEATER ON BPHE
PUMP OLP
YES
YES
YES
YES
COMPRESSOR OLP
YES
YES
DISCH. THERMOSTAT SETTING
kPa / psi
NC
°C / °F
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
114
Safety Devices - R407C Cooling only & Heat pump
MODEL
M4AC020C/CR
TYPE
HIGH PRESSURE
SWITCH
NC
NC
OPEN
kPa / psi
3243 / 470
3243 / 470
CLOSE
kPa / psi
2650 / 384
2650 / 384
LOW PRESSURE TYPE
SWITCH (COOLING OPEN
ONLY)
CLOSE
LOW PRESSURE
SAFETY DEVICE SWITCH (HEAT
PUMP)
M4AC025C/CR
NC
NC
kPa / psi
124 / 18
124 / 18
kPa / psi
193 / 28
193 / 28
TYPE
NC
NC
OPEN
kPa / psi
48 / 7
48 / 7
CLOSE
kPa / psi
152 / 22
152 / 22
DIFFERENTIAL PRESSURE SWITCH
YES
YES
ANTI-FREEZE PROTECTION SENSOR
YES
YES
OVER PRESSURE RELIEF VALVE
YES
YES
ANTI-FREEZE HEATER ON BPHE
YES
YES
PUMP OLP
YES
YES
COMPRESSOR OLP
YES
YES
M4AC030C/CR
M4AC040C/CR
MODEL
HIGH PRESSURE
SWITCH
LOW PRESSURE
SWITCH
(COOLING ONLY)
LOW PRESSURE
SWITCH (HEAT
SAFETY DEVICE PUMP)
TYPE
NC
NC
OPEN
kPa / psi
3243 / 470
3243 / 470
CLOSE
TYPE
kPa / psi
2650 / 384
2650 / 384
OPEN
NC
NC
kPa / psi
124 / 18
124 / 18
CLOSE
TYPE
kPa / psi
193 / 28
193 / 28
OPEN
kPa / psi
CLOSE
PHASE PROTECTION
NC
48 / 7
48 / 7
152 / 22
152 / 22
BUILT IN ON BOARD
BUILT IN ON BOARD
DIFFERENTIAL PRESSURE SWITCH
YES
YES
ANTI-FREEZE PROTECTION SENSOR
YES
YES
110 / 230
110 / 230
OVER PRESSURE RELIEF VALVE
YES
YES
ANTI-FREEZE HEATER ON BPHE
PUMP OLP
YES
YES
YES
YES
COMPRESSOR OLP
YES
YES
M4AC050C/CR
M4AC060C/CR
DISCH. THERMOSTAT SETTING
kPa / psi
NC
°C / °F
MODEL
HIGH PRESSURE
SWITCH
TYPE
OPEN
CLOSE
LOW PRESSURE TYPE
SWITCH (COOLING OPEN
ONLY)
CLOSE
LOW PRESSURE TYPE
SWITCH (HEAT
SAFETY DEVICE PUMP)
OPEN
CLOSE
PHASE PROTECTION
NC
NC
kPa / psi
3243 / 470
3243 / 470
kPa / psi
2650 / 384
2650 / 384
NC
NC
kPa / psi
124 / 18
124 / 18
kPa / psi
193 / 28
193 / 28
kPa / psi
NC
48 / 7
48 / 7
152 / 22
152 / 22
BUILT IN ON BOARD
BUILT IN ON BOARD
DIFFERENTIAL PRESSURE SWITCH
YES
YES
ANTI-FREEZE PROTECTION SENSOR
YES
YES
110 / 230
110 / 230
OVER PRESSURE RELIEF VALVE
YES
YES
ANTI-FREEZE HEATER ON BPHE
PUMP OLP
YES
YES
YES
YES
COMPRESSOR OLP
YES
YES
DISCH. THERMOSTAT SETTING
kPa / psi
NC
°C / °F
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
115
Safety Devices - R407C Cooling only & Heat pump
MODEL
M4AC080C/CR
TYPE
HIGH PRESSURE
SWITCH
NC
NC
OPEN
kPa / psi
3243 / 470
3243 / 470
CLOSE
kPa / psi
2650 / 384
2650 / 384
TYPE
LOW PRESSURE
SWITCH (COOLING OPEN
ONLY)
CLOSE
SAFETY DEVICE
LOW PRESSURE
SWITCH (HEAT
PUMP)
NC
NC
kPa / psi
124 / 18
124 / 18
kPa / psi
193 / 28
193 / 28
TYPE
NC
NC
OPEN
kPa / psi
48 / 7
48 / 7
CLOSE
kPa / psi
152 / 22
152 / 22
PHASE PROTECTION
BUILT IN ON BOARD
BUILT IN ON BOARD
DIFFERENTIAL PRESSURE SWITCH
YES
YES
ANTI-FREEZE PROTECTION SENSOR
YES
YES
110 / 230
110 / 230
OVER PRESSURE RELIEF VALVE
YES
YES
ANTI-FREEZE HEATER ON BPHE
YES
YES
PUMP OLP
YES
YES
COMPRESSOR OLP
YES
YES
M4AC120C/CR
M4AC150C/CR
DISCH. THERMOSTAT SETTING
°C / °F
MODEL
HIGH PRESSURE
SWITCH
TYPE
OPEN
CLOSE
LOW PRESSURE TYPE
SWITCH (COOLING OPEN
ONLY)
CLOSE
LOW PRESSURE TYPE
SAFETY DEVICE
M4AC100C/CR
SWITCH (HEAT
PUMP)
OPEN
CLOSE
PHASE PROTECTION
NC
NC
kPa / psi
3243 / 470
3243 / 470
kPa / psi
2650 / 384
2650 / 384
NC
NC
kPa / psi
124 / 18
124 / 18
kPa / psi
193 / 28
193 / 28
kPa / psi
NC
48 / 7
48 / 7
152 / 22
152 / 22
BUILT IN ON BOARD
BUILT IN ON BOARD
DIFFERENTIAL PRESSURE SWITCH
YES
YES
ANTI-FREEZE PROTECTION SENSOR
YES
YES
110 / 230
110 / 230
OVER PRESSURE RELIEF VALVE
YES
YES
ANTI-FREEZE HEATER ON BPHE
PUMP OLP
YES
YES
YES
YES
COMPRESSOR OLP
YES
YES
DISCH. THERMOSTAT SETTING
kPa / psi
NC
°C / °F
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
116
Safety Devices - R410A Heat pump
MODEL
M5AC030CR
HIGH PRESSURE
SWITCH
LOW PRESSURE
SWITCH
SAFETY DEVICE
TYPE
NC
OPEN
kPa / psi
4140 / 600
4140 / 600
CLOSE
TYPE
kPa / psi
3312 / 480
3312 / 480
OPEN
CLOSE
NC
NC
kPa / psi
124 / 18
124 / 18
kPa / psi
193 / 28
193 / 28
DIFFERENTIAL PRESSURE SWITCH
YES
YES
ANTI-FREEZE PROTECTION SENSOR
YES
YES
OVER PRESSURE RELIEF VALVE
YES
YES
ANTI-FREEZE HEATER ON BPHE
PUMP OLP
YES
YES
YES
YES
COMPRESSOR OLP
YES
YES
M5AC050CR
M5AC055CR
MODEL
HIGH PRESSURE
SWITCH
LOW PRESSURE
SWITCH
SAFETY DEVICE
M5AC040CR
NC
TYPE
NC
NC
OPEN
kPa / psi
4140 / 600
4140 / 600
CLOSE
TYPE
kPa / psi
3312 / 480
3312 / 480
OPEN
CLOSE
NC
NC
kPa / psi
124 / 18
124 / 18
kPa / psi
193 / 28
193 / 28
DIFFERENTIAL PRESSURE SWITCH
YES
YES
ANTI-FREEZE PROTECTION SENSOR
YES
YES
OVER PRESSURE RELIEF VALVE
YES
YES
ANTI-FREEZE HEATER ON BPHE
PUMP OLP
YES
YES
YES
YES
COMPRESSOR OLP
YES
YES
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
117
118
MAC060C
MAC050C
MAC040C
MAC030C
MAC025C
MAC020C
MODEL
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
LEAVING WATER TEMP (°C)
Cooling Only
Refrigerant : R22
4.62
5.00
5.38
5.76
6.13
6.51
6.89
8.52
8.67
8.83
8.98
9.14
9.29
9.45
8.85
9.02
9.18
9.35
9.52
9.68
9.85
11.73
12.19
12.65
13.10
13.56
14.02
14.48
15.57
15.86
16.16
16.45
16.74
17.04
17.33
16.18
16.48
16.77
17.07
17.37
17.66
17.96
COOL
CAP.
kW
20
2.18
2.19
2.21
2.22
2.24
2.25
2.27
1.90
1.90
1.91
1.92
1.93
1.94
1.95
2.43
2.48
2.53
2.58
2.62
2.67
2.72
3.14
3.16
3.17
3.19
3.21
3.23
3.24
3.68
3.70
3.73
3.75
3.77
3.79
3.81
4.47
4.49
4.52
4.54
4.57
4.60
4.62
POWER
INPUT
kW
4.49
4.84
5.18
5.53
5.88
6.22
6.57
7.65
7.85
8.04
8.24
8.44
8.64
8.84
8.05
8.30
8.55
8.81
9.06
9.31
9.56
11.22
11.71
12.19
12.68
13.16
13.65
14.14
14.46
14.90
15.33
15.77
16.21
16.65
17.08
15.25
15.65
16.05
16.44
16.84
17.24
17.64
COOL
CAP.
kW
25
2.32
2.34
2.35
2.37
2.39
2.40
2.42
2.13
2.16
2.19
2.22
2.24
2.27
2.30
2.80
2.84
2.89
2.94
2.99
3.03
3.08
3.34
3.40
3.46
3.52
3.58
3.64
3.70
4.20
4.22
4.24
4.26
4.28
4.30
4.32
5.12
5.16
5.20
5.24
5.28
5.32
5.36
POWER
INPUT
kW
4.30
4.62
4.94
5.26
5.59
5.91
6.23
6.72
6.94
7.17
7.39
7.62
7.85
8.07
7.25
7.59
7.92
8.26
8.60
8.94
9.27
10.62
11.15
11.68
12.20
12.73
13.26
13.79
13.35
13.93
14.51
15.09
15.67
16.25
16.83
14.32
14.82
15.32
15.82
16.32
16.82
17.32
COOL
CAP.
kW
30
2.49
2.51
2.53
2.55
2.56
2.58
2.60
2.37
2.41
2.46
2.51
2.56
2.60
2.65
3.16
3.21
3.26
3.30
3.35
3.39
3.44
3.79
3.86
3.93
4.00
4.06
4.13
4.20
4.73
4.76
4.79
4.83
4.86
4.89
4.92
5.77
5.82
5.88
5.93
5.98
6.04
6.09
POWER
INPUT
kW
4.25
4.59
4.88
5.28
5.44
5.72
5.94
5.94
6.26
6.55
6.89
7.12
7.41
7.67
6.59
7.08
7.45
8.06
8.18
8.55
8.79
10.25
10.81
11.36
11.72
12.47
13.02
13.58
12.56
13.20
13.84
14.65
15.12
15.76
16.40
13.42
14.01
14.59
15.53
15.77
16.35
16.94
COOL
CAP.
kW
35
2.60
2.62
2.64
2.68
2.68
2.70
2.72
2.60
2.65
2.69
2.74
2.78
2.82
2.86
3.40
3.43
3.46
3.50
3.53
3.56
3.59
4.03
4.16
4.29
4.50
4.25
4.68
4.81
5.21
5.23
5.24
5.26
5.28
5.29
5.31
6.32
6.34
6.36
6.38
6.40
6.42
6.44
POWER
INPUT
kW
3.92
4.19
4.46
4.73
5.00
5.28
5.55
4.85
5.13
5.41
5.70
5.98
6.26
6.55
5.65
6.16
6.67
7.17
7.68
8.19
8.70
9.41
10.03
10.64
11.25
11.87
12.48
13.10
11.13
12.00
12.87
13.73
14.60
15.47
16.34
12.46
13.16
13.87
14.57
15.27
15.98
16.68
COOL
CAP.
kW
40
AMBIENT TEMPERATURE ON CONDENSOR (°C)
2.84
2.86
2.88
2.90
2.92
2.94
2.96
2.84
2.93
3.01
3.09
3.18
3.26
3.35
3.90
3.94
3.98
4.03
4.07
4.11
4.16
4.68
4.77
4.85
4.94
5.03
5.12
5.20
5.80
5.85
5.91
5.96
6.01
6.07
6.12
7.07
7.15
7.24
7.32
7.40
7.48
7.56
POWER
INPUT
kW
3.84
4.10
4.36
4.63
4.89
5.15
5.41
3.92
4.23
4.54
4.85
5.16
5.47
5.78
5.33
5.87
6.41
6.96
7.50
8.04
8.58
9.17
9.80
10.43
11.06
11.70
12.33
12.96
10.68
11.61
12.54
13.46
14.39
15.32
16.24
11.53
12.33
13.14
13.94
14.75
15.56
16.36
COOL
CAP.
kW
42
2.91
2.93
2.95
2.97
2.99
3.01
3.03
3.08
3.18
3.28
3.39
3.49
3.59
3.70
4.05
4.09
4.13
4.17
4.21
4.26
4.30
4.86
4.95
5.04
5.13
5.22
5.31
5.40
6.02
6.07
6.13
6.19
6.24
6.30
6.36
7.72
7.82
7.91
8.01
8.10
8.20
8.29
POWER
INPUT
kW
3.60
3.85
4.10
4.36
4.61
4.86
5.11
3.64
3.93
4.23
4.53
4.83
5.12
5.42
4.69
5.30
5.91
6.52
7.13
7.74
8.35
8.55
9.24
9.93
10.62
11.30
11.99
12.68
9.79
10.84
11.88
12.92
13.96
15.00
16.05
11.34
12.17
12.99
13.82
14.65
15.47
16.30
COOL
CAP.
kW
46
3.09
3.11
3.13
3.15
3.17
3.19
3.21
3.12
3.23
3.34
3.44
3.55
3.66
3.76
4.34
4.38
4.42
4.46
4.50
4.55
4.59
5.55
5.60
5.65
5.70
5.76
5.81
5.86
6.48
6.56
6.64
6.72
6.80
6.88
6.96
7.85
7.95
8.05
8.15
8.25
8.34
8.44
POWER
INPUT
kW
Performance Data
119
5.20
5.56
5.74
6.20
6.69
7.23
6.29
6.70
7.11
7.52
8.01
8.70
28.75
29.62
30.27
30.50
31.06
31.90
35.67
36.82
37.12
37.88
38.53
39.54
42.88
44.19
45.10
45.54
46.38
47.57
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
MAC100C
MAC120C
MAC150C
7.23
7.81
8.17
8.67
9.35
10.12
4.31
4.64
4.83
5.16
5.58
6.03
25.18
25.92
26.15
26.47
27.30
27.92
5
6
7
8
9
10
MAC080C
COMP.
INPUT
kW
20
COOL
CAP.
kW
MODEL
Cooling Only
Refrigerant : R22
LEAVING WATER TEMP (°C)
41.39
42.58
43.55
44.04
44.98
45.90
34.55
35.65
36.08
36.76
37.51
38.38
27.80
28.65
29.26
29.56
30.18
30.90
24.03
24.75
25.05
25.38
26.15
26.69
COOL
CAP.
kW
25
8.22
8.83
9.27
9.79
10.53
11.52
6.99
7.45
7.88
8.31
8.88
9.73
6.01
6.42
6.68
7.13
7.67
8.39
4.95
5.31
5.55
5.89
6.35
6.94
COMP.
INPUT
kW
39.91
40.97
42.00
42.54
43.58
44.24
33.43
34.49
35.04
35.64
36.49
37.21
26.85
27.68
28.26
28.61
29.31
29.90
22.87
23.57
23.96
24.29
24.99
25.46
COOL
CAP.
kW
30
9.20
9.85
10.36
10.90
11.71
12.92
7.69
8.20
8.66
9.11
9.75
10.76
6.81
7.28
7.62
8.06
8.65
9.54
5.59
5.98
6.28
6.62
7.11
7.84
COMP.
INPUT
kW
38.42
39.36
40.44
41.05
42.18
42.57
32.30
33.32
34.00
34.51
35.46
36.04
25.90
26.71
27.26
27.67
28.43
28.90
21.71
22.40
22.86
23.20
23.84
24.23
COOL
CAP.
kW
35
10.19
10.88
11.45
12.02
12.89
14.31
8.39
8.96
9.43
9.90
10.61
11.79
7.62
8.13
8.56
8.99
9.63
10.70
6.23
6.65
7.00
7.35
7.88
8.75
COMP.
INPUT
kW
35.68
36.72
37.81
38.24
39.38
39.99
30.05
31.05
31.79
32.23
33.02
33.26
23.37
24.11
24.80
25.07
25.73
26.28
19.66
20.29
20.86
21.09
21.60
22.18
COOL
CAP.
kW
AMBIENT TEMPERATURE (°C)
40
11.34
12.04
12.69
13.22
14.21
15.32
9.38
9.98
10.57
10.98
11.72
13.25
8.52
9.06
9.53
9.97
10.65
11.58
6.94
7.39
7.77
8.13
8.66
9.43
COMP.
INPUT
kW
34.58
35.67
36.76
37.12
38.25
38.96
29.15
30.15
30.91
31.31
32.04
32.14
22.36
23.07
23.81
24.03
24.65
25.23
18.83
19.45
20.05
20.25
20.70
21.35
COOL
CAP.
kW
42
11.80
12.51
13.18
13.70
14.74
15.73
9.78
10.39
11.03
11.41
12.17
13.83
8.89
9.43
9.92
10.37
11.06
11.93
7.23
7.69
8.08
8.44
8.98
9.70
COMP.
INPUT
kW
32.39
33.56
34.66
34.88
36.01
36.90
27.35
28.33
29.14
29.48
30.09
29.92
20.34
20.98
21.84
21.95
22.49
23.13
17.19
17.76
18.45
18.57
18.91
19.71
COOL
CAP.
kW
46
12.71
13.44
14.17
14.66
15.80
16.53
10.56
11.21
11.94
12.27
13.06
15.00
9.61
10.17
10.70
11.15
11.88
12.64
7.80
8.28
8.69
9.07
9.61
10.25
COMP.
INPUT
kW
120
MAC060CR
MAC050CR
MAC040CR
MAC030CR
MAC025CR
MAC020CR
MODEL
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
3.29
3.31
3.55
3.57
3.59
3.61
3.63
3.65
3.67
4.82
4.83
4.84
4.85
4.86
4.87
4.88
14.48
14.33
14.60
14.87
15.14
15.41
15.68
15.94
16.18
16.48
16.77
17.07
17.37
17.66
17.96
12.65
14.02
3.22
3.24
12.19
3.27
3.20
11.73
3.26
2.76
10.71
13.56
2.71
10.53
13.10
2.66
1.99
9.24
10.36
1.99
9.09
2.61
1.98
8.94
10.19
1.97
8.78
2.56
1.96
8.63
10.01
1.95
8.48
2.51
1.94
8.33
9.84
2.21
6.89
2.46
2.19
6.51
9.66
2.18
6.13
2.15
5.38
2.16
2.13
5.76
2.12
5.00
POWER
INPUT
kW
4.62
COOL
CAP.
kW
20
Heatpump - Cooling Mode
Refrigerant : R22
LEAVING WATER TEMP (°C)
17.64
17.24
16.84
16.44
16.05
15.65
15.25
15.72
15.32
14.91
14.51
14.11
13.71
13.31
14.14
13.65
13.16
12.68
12.19
11.71
11.22
9.96
9.76
9.56
9.36
9.15
8.95
8.75
8.64
8.45
8.26
8.06
7.87
7.68
7.48
6.57
6.22
5.88
5.53
5.18
4.84
4.49
COOL
CAP.
kW
25
5.44
5.43
5.42
5.41
5.41
5.40
5.39
4.17
4.14
4.12
4.10
4.08
4.06
4.04
3.78
3.72
3.65
3.59
3.53
3.47
3.41
3.13
3.08
3.03
2.98
2.93
2.88
2.84
2.35
2.32
2.29
2.26
2.24
2.21
2.18
2.36
2.34
2.32
2.31
2.29
2.28
2.26
POWER
INPUT
kW
17.32
16.82
16.32
15.82
15.32
14.82
14.32
15.49
14.96
14.42
13.89
13.35
12.82
12.28
13.79
13.26
12.73
12.20
11.68
11.15
10.62
9.21
8.98
8.75
8.52
8.30
8.07
7.84
7.90
7.68
7.45
7.23
7.01
6.79
6.57
6.23
5.91
5.59
5.26
4.94
4.62
4.30
COOL
CAP.
kW
30
6.00
6.00
5.99
5.98
5.97
5.97
5.96
4.74
4.71
4.68
4.65
4.62
4.59
4.56
4.29
4.22
4.15
4.08
4.01
3.93
3.86
3.49
3.44
3.40
3.35
3.30
3.26
3.21
2.71
2.66
2.61
2.56
2.52
2.47
2.42
2.53
2.51
2.50
2.48
2.46
2.45
2.43
POWER
INPUT
kW
16.94
16.35
15.77
15.53
14.59
14.01
13.42
15.09
14.50
13.91
13.48
12.73
12.14
11.55
13.58
13.02
12.47
11.72
11.36
10.81
10.25
8.83
8.57
8.25
8.06
7.61
7.29
6.91
7.50
7.25
6.97
6.74
6.40
6.12
5.81
5.94
5.72
5.44
5.28
4.88
4.59
4.25
COOL
CAP.
kW
35
6.59
6.58
6.58
6.57
6.56
6.56
6.55
5.11
5.10
5.08
5.07
5.06
5.04
5.03
4.91
4.78
4.33
4.59
4.38
4.24
4.11
3.64
3.61
3.58
3.55
3.51
3.48
3.45
2.93
2.88
2.84
2.80
2.75
2.71
2.66
2.65
2.63
2.61
2.61
2.58
2.56
2.53
POWER
INPUT
kW
16.68
15.98
15.27
14.57
13.87
13.16
12.46
15.04
14.24
13.44
12.64
11.84
11.04
10.24
13.10
12.48
11.87
11.25
10.64
10.03
9.41
7.72
7.43
7.15
6.86
6.58
6.29
6.01
6.40
6.13
5.85
5.57
5.30
5.02
4.74
5.55
5.28
5.00
4.73
4.46
4.19
3.92
COOL
CAP.
kW
AMBIENT TEMPERATURE ON CONDENSOR (°C)
40
7.13
7.12
7.12
7.12
7.11
7.11
7.11
5.90
5.85
5.80
5.74
5.69
5.64
5.59
5.31
5.22
5.13
5.04
4.95
4.86
4.77
4.22
4.17
4.13
4.08
4.04
4.00
3.95
3.42
3.33
3.25
3.16
3.08
2.99
2.90
2.88
2.86
2.84
2.82
2.80
2.79
2.77
POWER
INPUT
kW
16.36
15.56
14.75
13.94
13.14
12.33
11.53
14.95
14.09
13.24
12.39
11.54
10.68
9.83
12.96
12.33
11.70
11.06
10.43
9.80
9.17
7.42
7.12
6.83
6.53
6.24
5.94
5.65
5.66
5.35
5.05
4.74
4.44
4.13
3.83
5.41
5.15
4.89
4.63
4.36
4.10
3.84
COOL
CAP.
kW
42
7.69
7.69
7.69
7.69
7.68
7.68
7.68
6.13
6.07
6.02
5.96
5.91
5.85
5.80
5.51
5.42
5.33
5.23
5.14
5.05
4.96
4.36
4.32
4.28
4.23
4.19
4.15
4.10
3.78
3.67
3.57
3.46
3.36
3.25
3.14
2.95
2.93
2.91
2.89
2.87
2.85
2.83
POWER
INPUT
kW
16.30
15.47
14.65
13.82
12.99
12.17
11.34
14.76
13.81
12.85
11.89
10.93
9.97
9.01
12.68
11.99
11.30
10.62
9.93
9.24
8.55
6.82
6.50
6.18
5.87
5.55
5.23
4.91
5.30
5.01
4.72
4.43
4.14
3.85
3.56
5.11
4.86
4.61
4.36
4.10
3.85
3.60
COOL
CAP.
kW
46
7.80
7.80
7.80
7.80
7.80
7.80
7.79
6.71
6.63
6.55
6.47
6.40
6.32
6.24
5.98
5.92
5.87
5.82
5.76
5.71
5.66
4.65
4.61
4.57
4.53
4.48
4.44
4.40
3.85
3.74
3.63
3.52
3.41
3.30
3.19
3.12
3.10
3.08
3.07
3.05
3.03
3.01
POWER
INPUT
kW
121
MAC150CR
MAC120CR
MAC100CR
MAC080CR
MODEL
5.58
6.10
23.17
23.59
24.11
24.75
27.44
27.69
28.93
29.46
30.10
30.96
33.52
34.25
35.06
35.48
36.29
37.60
39.50
40.91
41.54
42.64
43.55
45.07
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
9.97
9.22
8.55
8.10
7.66
7.13
8.87
8.19
7.61
7.22
6.82
6.33
7.63
7.05
6.54
6.11
5.87
5.47
6.53
5.27
5.02
22.75
4.66
22.02
6
COMP.
INPUT
kW
5
COOL
CAP.
kW
20
Heatpump - Cooling Mode
Refrigerant : R22
LEAVING WATER TEMP (°C)
44.57
43.07
42.15
41.17
40.45
39.07
36.98
35.71
34.91
34.43
33.64
32.79
30.53
29.63
28.99
28.47
27.44
26.97
24.60
23.91
23.39
22.97
22.52
21.79
COOL
CAP.
kW
25
11.45
10.47
9.73
9.24
8.76
8.17
10.15
9.28
8.64
8.21
7.77
7.24
8.93
8.16
7.59
7.15
6.84
6.39
7.67
7.05
6.51
6.17
5.87
5.47
COMP.
INPUT
kW
44.07
42.60
41.67
40.80
39.99
38.64
36.36
35.13
34.35
33.79
33.04
32.07
30.11
29.16
28.53
28.01
27.19
26.50
24.46
23.71
23.19
22.76
22.29
21.55
COOL
CAP.
kW
30
12.93
11.72
10.92
10.39
9.86
9.22
11.44
10.37
9.66
9.19
8.72
8.15
10.23
9.27
8.64
8.19
7.80
7.30
8.81
8.01
7.44
7.06
6.72
6.28
COMP.
INPUT
kW
43.58
42.12
41.19
40.43
39.53
38.21
35.74
34.55
33.79
33.16
32.43
31.34
29.69
28.70
28.07
27.54
26.93
26.03
24.32
23.50
22.98
22.56
22.06
21.32
COOL
CAP.
kW
35
14.41
12.97
12.10
11.53
10.96
10.27
12.72
11.45
10.69
10.18
9.67
9.06
11.53
10.38
9.69
9.23
8.77
8.21
9.96
8.96
8.37
7.96
7.57
7.09
COMP.
INPUT
kW
40.46
39.11
38.12
37.62
36.69
35.49
32.60
31.51
30.72
30.29
29.69
28.62
27.20
26.30
25.64
25.19
24.67
23.77
22.45
21.72
21.34
20.96
20.38
19.71
COOL
CAP.
kW
AMBIENT TEMPERATURE (°C)
40
15.10
13.88
13.01
12.48
11.84
11.12
13.29
12.23
11.41
10.95
10.39
9.80
12.32
11.34
10.59
10.16
9.65
9.07
10.41
9.61
8.96
8.63
8.14
7.69
COMP.
INPUT
kW
39.21
37.90
36.89
36.50
35.55
34.40
31.34
30.30
29.49
29.14
28.60
27.53
26.20
25.34
24.67
24.25
23.77
22.86
21.70
21.00
20.68
20.32
19.71
19.06
COOL
CAP.
kW
42
15.38
14.24
13.38
12.86
12.20
11.46
13.52
12.55
11.70
11.26
10.68
10.09
12.64
11.73
10.95
10.54
10.00
9.42
10.59
9.87
9.20
8.89
8.37
7.93
COMP.
INPUT
kW
36.71
35.49
34.43
34.25
33.27
32.23
28.82
27.87
27.03
26.85
26.41
25.36
24.21
23.42
22.74
22.37
21.96
21.05
20.21
19.57
19.36
19.04
18.37
17.77
COOL
CAP.
kW
46
15.93
14.96
14.11
13.62
12.91
12.15
13.97
13.17
12.28
11.88
11.26
10.68
13.27
12.50
11.68
11.29
10.71
10.10
10.95
10.38
9.68
9.42
8.83
8.41
COMP.
INPUT
kW
122
MAC060CR
MAC050CR
MAC040CR
MAC030CR
MAC025CR
MAC020CR
MODEL
11.09
10.65
55
11.98
40
50
12.42
35
11.54
9.13
55
45
9.25
9.50
40
50
9.62
35
9.37
5.81
45
6.48
55
7.82
40
50
8.49
35
7.15
4.96
55
45
5.12
5.44
40
50
5.60
35
5.28
5.00
55
45
5.07
5.23
40
50
5.31
35
5.15
2.87
55
45
3.31
50
4.18
3.74
4.61
35
40
45
HEAT
CAP.
kW
-7
7.63
7.02
6.42
5.81
5.20
6.22
5.59
4.95
4.32
3.69
5.35
4.83
4.33
3.82
3.32
4.19
3.79
3.40
3.00
2.61
3.03
2.78
2.54
2.29
2.05
2.72
2.57
2.42
2.27
2.13
POWER
INPUT
kW
Heatpump - Heating Mode
Refrigerant : R22
LEAVING WATER TEMP (°C)
11.34
11.77
12.20
12.63
13.06
9.79
9.92
10.04
10.17
10.29
6.52
7.15
7.78
8.41
9.05
5.46
5.60
5.75
5.89
6.03
5.19
5.26
5.32
5.39
5.46
3.19
3.62
4.04
4.47
4.90
HEAT
CAP.
kW
-5
7.64
7.03
6.43
5.82
5.21
6.19
5.57
4.95
4.33
3.71
5.42
4.90
4.39
2.31
3.35
4.21
3.81
3.42
3.02
2.62
3.04
2.79
2.54
2.29
2.04
2.76
2.60
2.45
2.30
2.15
POWER
INPUT
kW
13.23
13.62
14.01
14.40
14.79
11.63
11.75
11.88
12.00
12.13
8.47
8.99
9.51
10.03
10.55
6.71
6.84
6.97
7.11
7.24
5.73
5.86
5.99
6.13
6.26
4.05
4.46
4.88
5.29
5.70
HEAT
CAP.
kW
0
7.67
7.06
6.45
5.84
5.23
6.18
5.57
4.97
4.37
3.76
5.50
4.99
4.48
3.97
3.46
4.27
3.87
3.47
3.07
2.66
3.10
2.83
2.57
2.30
2.04
2.87
2.71
2.54
2.37
2.21
POWER
INPUT
kW
14.88
15.24
15.59
15.95
16.31
13.22
13.35
13.48
13.60
13.73
10.17
10.59
11.02
11.44
11.87
7.78
7.91
8.04
8.17
8.29
6.19
6.40
6.61
6.81
7.02
4.80
5.20
5.60
6.00
6.40
HEAT
CAP.
kW
4
7.70
7.09
6.47
5.86
5.25
6.17
5.58
4.99
4.40
3.81
5.55
5.05
4.55
4.05
3.55
4.33
3.92
3.51
3.11
2.70
3.15
2.87
2.60
2.32
2.05
2.97
2.79
2.62
2.44
2.26
POWER
INPUT
kW
16.79
17.11
17.29
17.75
18.07
14.90
15.09
15.24
15.48
15.68
11.95
12.27
12.60
13.29
13.59
8.83
8.97
9.23
9.27
9.41
6.68
6.95
7.33
7.48
7.75
5.53
6.08
6.45
6.88
7.13
HEAT
CAP.
kW
7
7.73
7.11
6.26
5.88
5.27
6.21
5.62
5.01
4.44
3.85
5.63
5.13
4.65
4.17
3.67
4.38
3.97
3.56
3.15
2.74
3.21
2.92
2.63
2.34
2.05
3.05
2.87
2.70
2.50
2.32
POWER
INPUT
kW
AMBIENT TEMPERATURE ON CONDENSOR (°C)
18.33
18.62
18.90
19.19
19.48
16.57
16.70
16.83
16.95
17.08
13.73
13.95
14.17
14.40
14.62
10.07
10.17
10.28
10.39
10.50
7.17
7.49
7.82
8.15
8.48
6.38
6.75
7.12
7.49
7.86
HEAT
CAP.
kW
10
7.75
7.14
6.52
5.90
5.28
6.14
5.58
5.02
4.47
3.91
5.71
5.22
4.73
4.24
3.75
4.44
4.02
3.61
3.19
2.77
3.25
2.95
2.65
2.35
2.05
3.18
2.98
2.77
2.57
2.37
POWER
INPUT
kW
19.12
19.39
19.66
19.93
20.20
17.33
17.46
17.59
17.72
17.84
14.54
14.71
14.89
15.07
15.25
10.59
10.69
10.79
10.89
11.00
7.39
7.74
8.10
8.45
8.81
6.73
7.10
7.46
7.83
8.19
HEAT
CAP.
kW
15
7.77
7.15
6.53
5.91
5.29
6.13
5.58
5.03
4.48
3.93
5.74
5.25
4.76
2.70
3.79
4.47
4.05
3.63
3.21
2.79
3.27
2.96
2.66
2.36
2.05
3.22
3.02
2.81
2.60
2.40
POWER
INPUT
kW
21.32
21.54
21.77
21.99
22.22
19.46
19.59
19.72
19.85
19.98
16.70
16.78
16.85
16.93
17.00
12.06
12.14
12.23
12.31
12.40
8.01
8.43
8.85
9.27
9.69
7.72
8.11
8.49
8.87
9.12
HEAT
CAP.
kW
21
7.80
7.18
6.56
5.94
5.32
6.10
5.57
5.05
4.52
3.99
5.84
5.35
4.87
4.39
3.91
4.54
4.11
3.69
3.26
2.84
3.33
3.01
2.69
2.37
2.06
3.37
3.14
2.92
2.70
2.47
POWER
INPUT
kW
123
MAC150CR
MAC120CR
MAC100CR
MAC080CR
MODEL
17.28
40
20.91
22.79
22.19
10.43
55
21.55
50
45
23.19
21.92
40
9.93
23.77
23.01
35
8.77
20.25
21.98
21.19
8.84
55
21.08
50
45
22.17
21.27
40
8.24
23.03
22.58
35
7.28
19.87
21.36
20.83
8.11
55
20.92
50
45
21.68
40
22.07
22.60
22.17
35
7.31
15.96
6.47
16.72
17.29
17.70
18.14
55
5.09
4.78
4.22
50
16.88
17.69
35
45
-5
0
4
7
AMBIENT TEMPERATURE (°C)
10
15
21
11.09
10.87
10.69
10.16
9.03
9.57
9.33
9.06
8.46
7.52
8.47
8.29
8.19
7.43
6.62
5.57
5.50
5.46
5.13
4.56
27.41
28.74
29.41
29.97
30.79
25.65
26.72
27.48
27.88
28.82
24.27
25.31
25.89
26.57
27.28
19.69
20.50
21.08
21.57
22.17
12.02
11.66
11.36
10.75
9.67
10.27
9.93
9.60
9.00
8.10
8.87
8.59
8.40
7.74
6.97
6.73
6.54
6.40
6.02
5.42
32.61
33.98
34.71
35.39
36.40
29.97
31.15
31.87
32.44
33.45
27.78
28.89
29.51
30.17
31.03
22.67
23.53
24.11
24.67
25.39
12.77
12.29
11.89
11.22
10.17
10.83
10.41
10.04
9.44
8.56
9.18
8.84
8.56
7.99
7.25
7.66
7.38
7.15
6.73
6.11
36.51
37.91
38.68
39.45
40.61
33.21
34.47
35.17
35.87
36.93
30.42
31.58
32.22
32.87
33.84
24.90
25.80
26.38
27.00
27.80
13.33
12.77
12.29
11.58
10.56
11.25
10.77
10.37
9.76
8.91
9.42
9.02
8.68
8.18
7.46
8.36
8.01
7.71
7.27
6.62
38.03
39.41
40.28
41.08
42.15
35.34
36.60
37.30
38.02
39.06
32.25
33.38
34.11
34.76
35.66
26.10
27.00
27.60
28.14
28.93
13.35
12.82
12.24
11.61
10.75
11.34
10.88
10.40
9.86
9.13
9.77
9.36
8.92
8.51
7.88
8.47
8.13
7.81
7.37
6.82
40.55
41.90
42.96
43.78
44.71
38.90
40.17
40.84
41.62
42.60
35.30
36.37
37.24
37.90
38.70
28.10
28.99
29.64
30.04
30.81
13.39
12.91
12.18
11.68
11.07
11.48
11.06
10.45
10.02
9.49
10.34
9.94
9.32
9.07
8.59
8.64
8.34
7.98
7.55
7.15
44.89
46.16
47.02
47.79
44.44
45.10
45.93
46.86
39.96
41.01
41.66
42.35
31.39
32.08
32.32
33.06
13.02
12.10
11.76
11.45
11.28
10.51
10.21
9.92
10.63
9.79
9.73
9.44
8.58
8.19
7.77
7.55
HEATING COMP. HEATING COMP. HEATING COMP. HEATING COMP. HEATING COMP. HEATING COMP. HEATING COMP. HEATING COMP.
CAP.
INPUT
CAP.
INPUT
CAP.
INPUT
CAP.
INPUT
CAP.
INPUT
CAP.
INPUT
CAP.
INPUT
CAP.
INPUT
kW
kW
kW
kW
kW
kW
kW
kW
kW
kW
kW
kW
kW
kW
kW
kW
-7
Heatpump - Heating Mode
Refrigerant : R22
LEAVING WATER TEMP (°C)
124
M4AC060C
M4AC050C
M4AC040C
M4AC030C
M4AC025C
M4AC020C
MODEL
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
5.38
5.82
6.26
6.70
7.14
7.59
8.03
8.33
8.48
8.63
8.78
8.94
9.09
9.24
8.69
8.85
9.01
9.18
9.34
9.50
9.66
11.73
12.19
12.65
13.10
13.56
14.02
14.48
15.57
15.86
16.16
16.45
16.74
17.04
17.33
15.88
16.17
16.46
16.75
17.04
17.33
17.62
COOL
CAP.
kW
Cooling Only
Refrigerant : R407C
LEAVING WATER TEMP (°C)
20
2.13
2.14
2.16
2.17
2.19
2.20
2.22
2.05
2.06
2.07
2.08
2.09
2.10
2.11
2.56
2.61
2.66
2.72
2.77
2.82
2.87
3.45
3.47
3.48
3.50
3.52
3.54
3.56
4.18
4.20
4.23
4.25
4.28
4.30
4.33
4.82
4.84
4.87
4.90
4.93
4.96
4.99
POWER
INPUT
kW
5.23
5.63
6.04
6.44
6.85
7.25
7.65
7.48
7.68
7.87
8.06
8.26
8.45
8.64
7.90
8.15
8.39
8.64
8.89
9.14
9.38
11.22
11.71
12.19
12.68
13.16
13.65
14.14
14.46
14.90
15.33
15.77
16.21
16.65
17.08
14.97
15.36
15.75
16.14
16.53
16.92
17.31
COOL
CAP.
kW
25
2.27
2.28
2.30
2.32
2.33
2.35
2.37
2.30
2.33
2.36
2.39
2.42
2.46
2.49
2.95
3.00
3.05
3.10
3.15
3.20
3.25
3.67
3.74
3.80
3.87
3.93
4.00
4.06
4.76
4.79
4.81
4.83
4.86
4.88
4.90
5.52
5.56
5.60
5.65
5.69
5.74
5.78
POWER
INPUT
kW
5.01
5.38
5.76
6.13
6.51
6.88
7.26
6.57
6.79
7.01
7.23
7.45
7.68
7.90
7.12
7.45
7.78
8.11
8.44
8.77
9.10
10.62
11.15
11.68
12.20
12.73
13.26
13.79
13.35
13.93
14.51
15.09
15.67
16.25
16.83
14.05
14.54
15.03
15.52
16.01
16.50
17.00
COOL
CAP.
kW
30
2.44
2.45
2.47
2.49
2.51
2.52
2.54
2.56
2.61
2.66
2.71
2.76
2.81
2.86
3.33
3.38
3.43
3.48
3.53
3.58
3.63
4.16
4.23
4.31
4.39
4.46
4.54
4.61
5.37
5.41
5.44
5.48
5.51
5.55
5.58
6.22
6.28
6.34
6.40
6.45
6.51
6.57
POWER
INPUT
kW
4.95
5.35
5.68
6.15
6.33
6.66
6.92
5.81
6.12
6.40
6.74
6.97
7.25
7.50
6.47
6.95
7.31
7.91
8.03
8.39
8.63
10.25
10.81
11.36
11.72
12.47
13.02
13.58
12.56
13.20
13.84
14.65
15.12
15.76
16.40
13.17
13.75
14.32
15.24
15.47
16.05
16.62
COOL
CAP.
kW
35
2.54
2.57
2.59
2.62
2.62
2.64
2.66
2.81
2.86
2.91
2.96
3.00
3.05
3.09
3.58
3.62
3.65
3.69
3.72
3.75
3.79
4.42
4.57
4.71
4.94
4.66
5.14
5.28
5.92
5.94
5.95
5.97
5.99
6.00
6.02
6.82
6.84
6.86
6.88
6.90
6.92
6.94
POWER
INPUT
kW
4.56
4.88
5.19
5.51
5.83
6.14
6.46
4.74
5.02
5.30
5.57
5.85
6.13
6.40
5.54
6.04
6.54
7.04
7.54
8.04
8.54
9.41
10.03
10.64
11.25
11.87
12.48
13.10
11.13
12.00
12.87
13.73
14.60
15.47
16.34
12.23
12.92
13.61
14.30
14.99
15.68
16.37
COOL
CAP.
kW
40
2.78
2.80
2.81
2.83
2.85
2.87
2.89
3.07
3.16
3.25
3.34
3.43
3.52
3.62
4.11
4.16
4.20
4.25
4.29
4.34
4.38
5.14
5.23
5.33
5.42
5.52
5.62
5.71
6.59
6.65
6.70
6.76
6.82
6.88
6.94
7.63
7.71
7.80
7.89
7.98
8.07
8.15
POWER
INPUT
kW
AMBIENT TEMPERATURE ON CONDENSOR (°C)
4.47
4.78
5.08
5.39
5.69
6.00
6.30
3.83
4.13
4.44
4.74
5.05
5.35
5.66
5.23
5.76
6.29
6.83
7.36
7.89
8.42
9.17
9.80
10.43
11.06
11.70
12.33
12.96
10.68
11.61
12.54
13.46
14.39
15.32
16.24
11.31
12.10
12.89
13.68
14.47
15.27
16.06
COOL
CAP.
kW
42
2.84
2.86
2.88
2.90
2.92
2.94
2.96
3.32
3.44
3.55
3.66
3.77
3.88
3.99
4.27
4.31
4.35
4.40
4.44
4.49
4.53
5.33
5.43
5.53
5.63
5.73
5.83
5.93
6.83
6.89
6.96
7.02
7.09
7.15
7.22
8.33
8.43
8.53
8.64
8.74
8.84
8.94
POWER
INPUT
kW
4.20
4.49
4.78
5.07
5.37
5.66
5.95
3.56
3.85
4.14
4.43
4.72
5.01
5.30
4.60
5.20
5.80
6.40
7.00
7.60
8.20
8.55
9.24
9.93
10.62
11.30
11.99
12.68
9.79
10.84
11.88
12.92
13.96
15.00
16.05
11.13
11.94
12.75
13.56
14.37
15.18
15.99
COOL
CAP.
kW
46
3.02
3.04
3.06
3.08
3.10
3.12
3.13
3.38
3.49
3.61
3.72
3.84
3.95
4.07
4.58
4.62
4.66
4.71
4.75
4.79
4.84
6.09
6.15
6.20
6.26
6.32
6.38
6.43
7.35
7.44
7.53
7.62
7.72
7.81
7.90
8.47
8.58
8.68
8.79
8.89
9.00
9.10
POWER
INPUT
kW
125
5.42
5.80
5.99
6.47
6.98
7.53
6.47
6.89
7.31
7.74
8.26
8.94
7.81
8.45
8.84
9.38
10.12
10.94
34.02
35.12
35.41
36.12
36.72
37.71
42.36
43.67
44.54
44.97
45.77
47.00
5
6
7
8
9
10
5
6
7
8
9
10
M4AC100C
M4AC120C
M4AC150C
4.73
5.09
5.30
5.66
6.13
6.61
COMP.
INPUT
kW
26.39
27.19
27.77
27.98
28.48
29.27
M4AC080C
23.77
24.46
24.68
24.98
25.74
26.34
COOL
CAP.
kW
20
5
6
7
8
9
10
5
6
7
8
9
10
MODEL
Cooling Only
Refrigerant : R407C
LEAVING WATER TEMP (°C)
41.69
42.98
43.76
44.25
45.03
46.24
33.64
34.70
35.18
35.71
36.32
37.30
25.83
26.63
27.12
27.41
27.89
28.65
22.60
23.29
23.61
23.89
24.43
25.05
COOL
CAP.
kW
25
8.87
9.57
10.07
10.65
11.50
12.41
7.39
7.94
8.39
8.86
9.53
10.30
6.51
7.01
7.33
7.80
8.42
9.09
5.57
6.00
6.30
6.68
7.22
7.79
COMP.
INPUT
kW
40.46
42.04
42.65
43.09
43.84
44.88
32.99
34.31
34.68
35.14
35.85
36.60
25.18
26.19
26.47
26.83
27.36
27.93
21.51
22.37
22.61
22.91
23.37
23.86
COOL
CAP.
kW
30
9.94
10.68
11.26
11.87
12.81
13.79
8.31
8.93
9.41
9.92
10.71
11.53
7.50
8.05
8.49
8.95
9.66
10.40
6.36
6.83
7.20
7.59
8.19
8.82
COMP.
INPUT
kW
38.15
39.36
40.16
40.76
41.89
42.57
32.02
33.03
33.70
34.21
35.15
35.72
24.50
25.27
25.79
26.18
26.90
27.34
20.60
21.25
21.69
22.01
22.62
22.99
COOL
CAP.
kW
35
10.86
11.59
12.20
12.81
13.73
15.25
9.08
9.69
10.20
10.71
11.48
12.75
8.19
8.74
9.20
9.66
10.35
11.50
6.94
7.41
7.80
8.19
8.78
9.75
COMP.
INPUT
kW
36.95
38.19
39.00
39.76
40.96
42.17
30.36
31.38
32.04
32.67
33.66
34.65
23.18
23.97
24.47
24.95
25.70
26.46
19.32
19.97
20.39
20.79
21.42
22.05
COOL
CAP.
kW
AMBIENT TEMPERATURE (°C)
40
11.47
12.20
12.81
13.42
14.34
15.31
9.59
10.20
10.71
11.22
11.99
12.80
8.65
9.20
9.66
10.12
10.81
11.55
7.33
7.80
8.19
8.58
9.17
9.79
COMP.
INPUT
kW
34.90
36.14
37.31
37.55
38.39
39.76
28.24
29.25
30.19
30.39
31.07
32.18
21.55
22.32
23.04
23.19
23.71
24.55
17.38
18.00
18.58
18.70
19.12
19.80
COOL
CAP.
kW
42
12.25
12.98
13.65
14.21
15.15
16.12
10.24
10.85
11.41
11.88
12.67
13.47
9.24
9.79
10.29
10.72
11.43
12.15
7.83
8.30
8.73
9.09
9.69
10.30
COMP.
INPUT
kW
31.75
32.90
33.98
34.20
35.30
36.18
26.26
27.20
27.98
28.31
28.89
29.92
18.90
19.50
20.30
20.40
20.90
21.50
15.00
15.50
16.10
16.20
16.50
17.20
COOL
CAP.
kW
46
14.00
14.80
15.61
16.15
17.40
18.21
11.45
12.15
12.94
13.30
14.15
15.00
9.97
10.55
11.10
11.57
12.32
13.11
8.53
9.05
9.50
9.91
10.50
11.20
COMP.
INPUT
kW
126
M4AC060CR
M4AC050CR
M4AC040CR
M4AC030CR
M4AC025CR
M4AC020CR
MODEL
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4.36
4.71
5.07
5.43
5.79
6.14
6.50
7.97
8.12
8.26
8.41
8.55
8.70
8.84
8.79
8.95
9.10
9.26
9.42
9.58
9.74
11.73
12.19
12.65
13.10
13.56
14.02
14.48
14.33
14.60
14.87
15.14
15.41
15.68
15.94
15.58
15.86
16.15
16.43
16.72
17.00
17.29
COOL
CAP.
kW
20
2.12
2.13
2.15
2.16
2.18
2.19
2.21
2.14
2.15
2.16
2.17
2.18
2.19
2.20
2.65
2.70
2.76
2.81
2.86
2.92
2.97
3.38
3.40
3.42
3.44
3.46
3.48
3.50
3.83
3.85
3.87
3.90
3.92
3.94
3.96
4.79
4.80
4.81
4.82
4.83
4.84
4.85
POWER
INPUT
kW
Heatpump - Cooling Mode
Refrigerant : R407C
LEAVING WATER TEMP (°C)
4.23
4.56
4.89
5.22
5.54
5.87
6.20
7.16
7.35
7.53
7.72
7.90
8.09
8.27
7.96
8.14
8.32
8.51
8.69
8.87
9.06
11.22
11.71
12.19
12.68
13.16
13.65
14.14
13.31
13.71
14.11
14.51
14.91
15.32
15.72
14.68
15.06
15.45
15.83
16.21
16.60
16.98
COOL
CAP.
kW
25
2.26
2.28
2.29
2.31
2.32
2.34
2.36
2.40
2.44
2.47
2.50
2.53
2.56
2.59
3.05
3.10
3.16
3.21
3.26
3.31
3.36
3.60
3.67
3.73
3.80
3.86
3.93
3.99
4.36
4.38
4.41
4.43
4.45
4.47
4.49
5.36
5.36
5.37
5.38
5.39
5.40
5.41
POWER
INPUT
kW
4.05
4.36
4.66
4.96
5.27
5.57
5.88
6.29
6.50
6.71
6.92
7.13
7.35
7.56
7.13
7.34
7.54
7.75
7.96
8.17
8.38
10.62
11.15
11.68
12.20
12.73
13.26
13.79
12.28
12.82
13.35
13.89
14.42
14.96
15.49
13.78
14.27
14.75
15.23
15.71
16.19
16.67
COOL
CAP.
kW
30
2.43
2.45
2.46
2.48
2.50
2.51
2.53
2.67
2.72
2.78
2.83
2.88
2.93
2.99
3.45
3.50
3.55
3.60
3.65
3.70
3.75
4.08
4.16
4.23
4.31
4.38
4.46
4.53
4.92
4.95
4.99
5.02
5.05
5.08
5.12
5.92
5.93
5.94
5.95
5.95
5.96
5.97
POWER
INPUT
kW
4.01
4.33
4.60
4.98
5.13
5.39
5.60
5.56
5.86
6.13
6.45
6.67
6.94
7.18
6.28
6.63
6.92
7.33
7.50
7.80
8.03
10.25
10.81
11.36
11.72
12.47
13.02
13.58
11.55
12.14
12.73
13.48
13.91
14.50
15.09
12.92
13.48
14.05
14.95
15.18
15.74
16.31
COOL
CAP.
kW
35
2.53
2.56
2.58
2.61
2.61
2.63
2.65
2.94
2.99
3.03
3.09
3.13
3.18
3.23
3.71
3.74
3.78
3.82
3.85
3.88
3.92
4.34
4.48
4.62
4.85
4.58
5.05
5.19
5.42
5.44
5.45
5.47
5.49
5.50
5.52
6.51
6.52
6.52
6.53
6.54
6.54
6.55
POWER
INPUT
kW
3.69
3.95
4.21
4.46
4.72
4.98
5.23
4.54
4.80
5.07
5.33
5.60
5.86
6.13
5.47
5.72
5.98
6.24
6.50
6.76
7.02
9.41
10.03
10.64
11.25
11.87
12.48
13.10
10.24
11.04
11.84
12.64
13.44
14.24
15.04
11.99
12.67
13.35
14.02
14.70
15.38
16.06
COOL
CAP.
kW
40
AMBIENT TEMPERATURE ON CONDENSOR (°C)
2.77
2.79
2.80
2.82
2.84
2.86
2.88
3.20
3.30
3.39
3.49
3.58
3.68
3.77
4.25
4.30
4.35
4.40
4.44
4.49
4.54
5.04
5.14
5.23
5.33
5.42
5.51
5.61
6.03
6.09
6.14
6.20
6.25
6.31
6.36
7.06
7.07
7.07
7.07
7.08
7.08
7.09
POWER
INPUT
kW
3.62
3.87
4.12
4.36
4.61
4.86
5.10
3.67
3.96
4.25
4.54
4.83
5.12
5.41
5.13
5.40
5.67
5.94
6.21
6.48
6.75
9.17
9.80
10.43
11.06
11.70
12.33
12.96
9.83
10.68
11.54
12.39
13.24
14.09
14.95
11.10
11.87
12.65
13.42
14.20
14.97
15.75
COOL
CAP.
kW
42
2.83
2.85
2.87
2.89
2.91
2.93
2.95
3.47
3.59
3.70
3.82
3.93
4.05
4.17
4.42
4.46
4.51
4.55
4.60
4.65
4.69
5.24
5.33
5.43
5.53
5.63
5.73
5.82
6.26
6.32
6.37
6.43
6.49
6.55
6.61
7.63
7.64
7.64
7.64
7.64
7.64
7.64
POWER
INPUT
kW
3.40
3.63
3.87
4.11
4.34
4.58
4.82
3.40
3.68
3.96
4.24
4.52
4.80
5.07
4.47
4.76
5.05
5.34
5.62
5.91
6.20
8.55
9.24
9.93
10.62
11.30
11.99
12.68
9.01
9.97
10.93
11.89
12.85
13.81
14.76
10.92
11.71
12.51
13.30
14.10
14.89
15.69
COOL
CAP.
kW
46
3.01
3.03
3.05
3.07
3.08
3.10
3.12
3.52
3.64
3.76
3.88
4.01
4.13
4.25
4.74
4.78
4.83
4.87
4.92
4.96
5.01
5.98
6.03
6.09
6.15
6.20
6.26
6.32
6.73
6.82
6.90
6.99
7.07
7.15
7.24
7.75
7.75
7.75
7.75
7.75
7.76
7.76
POWER
INPUT
kW
127
25.80
26.05
27.21
27.71
28.30
29.11
33.03
33.75
34.55
34.96
35.76
37.05
38.26
39.63
40.23
41.29
42.18
43.65
5
6
7
8
9
10
5
6
7
8
9
10
5
6
7
8
9
10
M4AC100CR
M4AC120CR
M4AC150CR
M4AC080CR
21.16
21.86
22.26
22.66
23.16
23.77
COOL
CAP.
kW
5
6
7
8
9
10
MODEL
20
8.27
8.89
9.40
9.93
10.71
11.56
6.53
7.04
7.45
7.86
8.47
9.14
5.63
6.06
6.30
6.75
7.28
7.86
4.91
5.30
5.56
5.89
6.44
6.88
COMP.
INPUT
kW
Heatpump - Cooling Mode
Refrigerant : R407C
LEAVING WATER TEMP (°C)
37.51
38.84
39.52
40.47
41.35
42.79
32.18
33.01
33.78
34.26
35.03
36.28
25.33
25.77
26.73
27.23
27.83
28.68
20.94
21.64
22.07
22.48
22.98
23.64
COOL
CAP.
kW
25
9.53
10.26
10.82
11.44
12.35
13.33
7.82
8.43
8.90
9.40
10.14
10.95
6.91
7.44
7.81
8.28
8.94
9.65
5.89
6.34
6.68
7.06
7.65
8.24
COMP.
INPUT
kW
36.75
38.04
38.81
39.64
40.52
41.93
31.32
32.27
33.01
33.55
34.31
35.52
24.85
25.50
26.26
26.76
27.35
28.24
20.72
21.43
21.88
22.29
22.79
23.51
COOL
CAP.
kW
30
10.75
11.55
12.17
12.84
13.86
14.91
8.99
9.66
10.19
10.74
11.59
12.48
8.02
8.61
9.08
9.57
10.34
11.12
6.77
7.26
7.66
8.07
8.72
9.38
COMP.
INPUT
kW
36.00
37.25
38.10
38.82
39.70
41.06
30.47
31.53
32.24
32.85
33.59
34.75
24.37
25.22
25.79
26.28
26.87
27.80
20.50
21.21
21.69
22.10
22.60
23.38
COOL
CAP.
kW
35
11.75
12.54
13.20
13.86
14.85
16.50
9.83
10.49
11.04
11.59
12.42
13.80
8.76
9.35
9.84
10.33
11.07
12.30
7.39
7.89
8.30
8.72
9.34
10.38
COMP.
INPUT
kW
34.09
35.35
36.15
36.76
37.72
38.86
28.85
29.92
30.59
31.11
31.92
32.88
23.08
23.93
24.48
24.89
25.53
26.31
19.41
20.13
20.58
20.93
21.47
22.12
COOL
CAP.
kW
AMBIENT TEMPERATURE (°C)
40
12.41
13.20
13.86
14.52
15.51
16.56
10.38
11.04
11.59
12.14
12.97
13.86
9.25
9.84
10.33
10.82
11.56
12.35
7.80
8.30
8.72
9.13
9.75
10.42
COMP.
INPUT
kW
31.81
33.15
33.72
34.29
35.35
36.57
26.92
28.05
28.53
29.02
29.92
30.95
21.54
22.44
22.83
23.21
23.93
24.76
18.11
18.87
19.19
19.52
20.13
20.82
COOL
CAP.
kW
42
13.25
14.05
14.78
15.38
16.39
17.44
11.08
11.75
12.35
12.86
13.71
14.58
9.88
10.47
11.01
11.46
12.22
13.00
8.33
8.83
9.29
9.67
10.31
10.96
COMP.
INPUT
kW
30.82
31.82
32.75
32.92
33.94
35.11
24.50
25.52
25.94
26.12
26.93
27.85
20.00
20.86
21.25
21.60
22.25
23.00
16.80
17.36
18.00
18.30
18.50
19.10
COOL
CAP.
kW
46
14.44
15.34
16.18
16.76
17.78
18.93
12.00
12.65
13.35
13.80
14.80
15.70
10.47
11.10
11.70
12.10
12.95
13.75
8.91
9.35
9.98
10.25
11.00
11.60
COMP.
INPUT
kW
128
M4AC060CR
M4AC050CR
M4AC040CR
M4AC030CR
M4AC025CR
M4AC020CR
MODEL
35
40
45
50
55
35
40
45
50
55
35
40
45
50
55
35
40
45
50
55
35
40
45
50
55
35
40
45
50
55
7.04
7.65
10.83
5.83
12.18
11.28
5.22
12.63
6.44
7.03
8.95
11.73
6.31
4.88
9.32
5.59
4.17
9.44
9.07
5.76
9.20
5.21
6.08
5.80
8.19
6.78
3.57
8.89
4.66
4.71
5.12
7.49
4.26
5.29
3.37
5.62
3.82
2.93
5.78
5.45
3.17
5.09
2.40
5.33
2.91
2.14
5.41
5.17
2.71
2.61
2.66
2.56
3.00
5.25
2.41
2.26
3.79
3.40
2.12
4.19
HEAT POWER
CAP.
INPUT
kW
kW
-7
Heatpump - Heating Mode
Refrigerant : R407C
LEAVING WATER TEMP (°C)
11.53
11.97
12.40
12.84
13.28
9.61
9.73
9.85
9.97
10.10
6.83
7.49
8.15
8.81
9.47
5.64
5.79
5.93
6.08
6.23
5.29
5.36
5.43
5.49
5.56
2.89
3.28
3.67
4.06
4.45
7.66
7.05
6.45
5.84
5.23
7.00
6.29
5.60
4.89
4.19
5.84
5.28
4.73
4.17
3.61
4.73
4.29
3.84
3.39
2.95
3.18
2.92
2.66
2.39
2.13
2.75
2.60
2.44
2.29
2.14
HEAT POWER
CAP.
INPUT
kW
kW
-5
13.45
13.85
14.25
14.65
15.04
11.41
11.53
11.65
11.77
11.90
8.87
9.41
9.96
10.50
11.05
6.93
7.07
7.20
7.34
7.47
5.83
5.97
6.11
6.24
6.38
3.68
4.05
4.43
4.81
5.18
7.69
7.08
6.47
5.86
5.25
6.98
6.30
5.62
4.93
4.25
5.93
5.38
4.83
4.28
3.73
4.80
4.35
3.90
3.44
2.99
3.24
2.96
2.69
2.41
2.13
2.86
2.70
2.53
2.37
2.20
HEAT POWER
CAP.
INPUT
kW
kW
0
15.13
15.49
15.85
16.22
16.58
12.97
13.10
13.22
13.34
13.47
10.64
11.09
11.53
11.98
12.42
8.03
8.17
8.30
8.43
8.56
6.31
6.52
6.73
6.94
7.16
4.36
4.72
5.09
5.45
5.81
7.72
7.11
6.49
5.88
5.27
6.97
6.30
5.64
4.97
4.30
5.98
5.45
4.91
4.37
3.83
4.86
4.40
3.95
3.49
3.03
3.29
3.00
2.72
2.43
2.14
2.96
2.78
2.61
2.43
2.25
HEAT POWER
CAP.
INPUT
kW
kW
4
17.07
17.40
17.58
18.05
18.37
14.61
14.81
14.95
15.19
15.38
12.51
12.85
13.19
13.91
14.23
9.11
9.27
9.53
9.57
9.72
6.81
7.08
7.47
7.62
7.90
5.03
5.53
5.86
6.25
6.48
7.75
7.13
6.28
5.90
5.28
7.02
6.35
5.66
5.01
4.35
6.07
5.53
5.01
4.49
3.96
4.92
4.46
4.00
3.54
3.08
3.36
3.05
2.75
2.45
2.14
3.04
2.86
2.69
2.49
2.31
HEAT POWER
CAP.
INPUT
kW
kW
7
10
17.51
17.82
18.14
18.45
18.77
15.20
15.32
15.45
15.57
15.70
13.17
13.47
13.78
14.08
14.38
9.64
9.75
9.87
9.99
10.11
6.98
7.28
7.57
7.87
8.16
5.33
5.68
6.02
6.37
6.71
7.76
7.14
6.53
5.91
5.29
6.95
6.31
5.66
5.02
4.38
6.10
5.56
5.03
4.50
3.97
4.95
4.48
4.02
3.55
3.09
3.36
3.06
2.75
2.45
2.14
3.10
2.91
2.71
2.52
2.33
HEAT POWER
CAP.
INPUT
kW
kW
AMBIENT TEMPERATURE ON CONDENSOR (°C)
19.44
19.71
19.99
20.26
20.53
17.00
17.13
17.25
17.38
17.50
15.22
15.40
15.59
15.78
15.96
10.93
11.04
11.14
11.25
11.35
7.53
7.89
8.25
8.62
8.98
6.12
6.45
6.78
7.11
7.44
7.79
7.17
6.55
5.93
5.31
6.93
6.31
5.68
5.06
4.44
6.18
5.66
5.13
4.61
4.08
5.02
4.55
4.08
3.61
3.14
3.42
3.10
2.78
2.46
2.15
3.21
3.01
2.80
2.59
2.39
HEAT POWER
CAP.
INPUT
kW
kW
15
21.68
21.91
22.13
22.36
22.59
19.09
19.22
19.35
19.48
19.60
17.48
17.56
17.64
17.72
17.80
12.45
12.54
12.63
12.71
12.80
8.16
8.59
9.02
9.45
9.87
7.02
7.36
7.71
8.06
8.29
7.83
7.20
6.58
5.96
5.33
6.89
6.30
5.70
5.11
4.51
6.29
5.77
5.25
4.73
4.22
5.10
4.62
4.14
3.67
3.19
3.48
3.15
2.82
2.48
2.15
3.35
3.13
2.91
2.69
2.46
HEAT POWER
CAP.
INPUT
kW
kW
21
129
8.30
9.30
10.00
9.93
11.22
11.81
19.90
19.20
18.80
24.26
23.73
23.20
35
40
45
50
55
35
40
45
50
55
M4AC120CR
M4AC150CR
6.40
7.20
7.70
17.10
16.70
16.30
M4AC100CR
kW
kW
7.30
8.10
9.00
INPUT
CAP.
18.10
17.70
17.00
35
40
45
50
55
COMP.
HEATING
35
40
45
50
55
M4AC080CR
MODEL
-7
Heatpump- Heating Mode
Refrigerant : R407C
LEAVING WATER TEMP (°C)
27.72
27.04
26.58
25.87
24.39
22.71
21.86
21.68
20.90
19.97
19.15
18.70
18.10
17.65
16.84
18.61
18.15
17.73
17.15
16.37
kW
CAP.
HEATING
-5
10.18
11.46
12.06
12.26
12.51
8.38
9.43
10.10
10.40
10.67
7.35
8.26
9.10
9.21
9.41
6.52
7.33
7.80
7.85
7.95
kW
INPUT
COMP.
40.18
39.25
38.40
37.56
35.87
32.92
32.16
31.47
30.78
29.40
27.34
26.71
26.14
25.56
24.41
25.11
24.53
24.00
23.48
22.42
kW
CAP.
HEATING
0
10.72
12.06
12.73
12.90
13.20
8.64
9.72
10.40
10.70
11.00
7.60
8.55
9.20
9.50
9.70
6.69
7.52
7.94
8.03
8.18
kW
INPUT
COMP.
43.05
41.78
40.89
40.10
39.04
35.27
34.24
33.51
32.85
31.99
29.30
28.43
27.83
27.29
26.57
26.90
26.11
25.56
25.06
24.40
kW
CAP.
HEATING
4
10.99
12.47
13.06
13.67
14.07
8.86
10.04
10.53
11.02
11.34
7.79
8.84
9.30
9.69
9.98
6.86
7.77
8.15
8.53
8.78
kW
INPUT
COMP.
44.31
43.05
42.20
41.36
39.84
36.31
35.27
34.58
33.89
32.65
30.16
29.30
28.72
28.15
27.11
27.70
26.90
26.38
25.85
24.90
kW
CAP.
HEATING
7
11.51
12.63
13.40
13.93
14.54
9.28
10.17
10.80
11.22
11.72
8.16
8.95
9.50
9.87
10.31
7.18
7.88
8.36
8.69
9.07
kW
INPUT
COMP.
AMBIENT TEMPERATURE (°C)
45.24
44.70
43.81
42.96
41.78
37.07
36.62
35.90
35.21
34.24
30.79
30.42
29.81
29.24
28.43
28.28
27.93
27.38
26.85
26.11
kW
CAP.
HEATING
10
12.33
13.02
13.67
14.47
14.78
9.94
10.50
11.02
11.66
11.91
8.74
9.23
9.69
10.26
10.48
7.69
8.13
8.53
9.03
9.22
kW
INPUT
COMP.
47.26
46.51
45.67
44.81
43.55
38.73
38.11
37.42
36.73
35.69
32.17
31.65
31.08
30.50
29.64
29.54
29.07
28.54
28.01
27.22
kW
CAP.
HEATING
15
13.13
13.54
13.94
14.90
15.41
10.58
10.91
11.20
12.01
12.42
9.31
9.60
9.75
10.56
10.93
8.19
8.44
8.90
9.30
9.61
kW
INPUT
COMP.
51.99
51.16
50.22
48.84
42.60
41.75
41.00
40.40
36.35
35.76
35.20
34.30
33.60
32.85
32.60
31.90
kW
CAP.
HEATING
21
13.53
13.90
14.29
15.39
10.90
11.22
11.55
12.40
9.51
9.80
9.86
10.70
8.45
8.69
9.16
9.60
kW
INPUT
COMP.
130
M5AC055CR
M5AC050CR
M5AC040CR
M5AC030CR
M5AC025CR
M5AC020CR
MODEL
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
4
5
6
7
8
9
10
kW
2.02
2.04
2.05
2.07
2.08
2.10
2.11
2.09
2.12
2.16
2.19
2.23
2.26
2.30
2.04
2.06
2.08
2.11
2.13
2.15
2.17
1.63
2.07
2.45
2.94
3.22
3.61
3.94
3.15
3.17
3.19
3.21
3.22
3.24
3.26
3.92
3.93
3.94
3.95
3.96
3.97
3.98
kW
5.61
6.13
6.58
7.03
7.34
7.85
8.22
6.57
6.95
7.31
7.72
8.02
8.38
8.71
9.37
9.83
10.15
10.76
10.78
11.10
11.27
11.74
11.95
12.30
12.36
12.99
13.34
13.83
15.33
15.55
15.63
15.98
15.81
15.89
15.85
15.32
15.83
16.07
16.84
16.56
16.81
16.79
POWER
INPUT
COOL
CAP.
20
Heatpump- Cooling Mode
Refrigerant : R410A
LEAVING WATER TEMP (°C)
5.04
5.49
5.90
6.30
6.58
7.04
7.35
6.12
6.50
6.84
7.24
7.52
7.86
8.17
8.49
8.92
9.24
9.79
9.87
10.18
10.38
11.02
11.31
11.72
11.89
12.52
12.93
13.45
14.15
14.51
14.77
15.24
15.29
15.55
15.70
14.43
14.99
15.34
16.11
16.03
16.38
16.52
kW
COOL
CAP.
25
2.18
2.20
2.22
2.24
2.25
2.27
2.28
2.24
2.28
2.31
2.35
2.38
2.42
2.46
2.45
2.48
2.51
2.53
2.55
2.58
2.60
2.20
2.54
2.83
3.21
3.42
3.71
3.96
3.59
3.60
3.62
3.64
3.65
3.67
3.69
4.37
4.38
4.39
4.40
4.41
4.42
4.42
kW
POWER
INPUT
4.48
4.86
5.22
5.58
5.83
6.22
6.47
5.68
6.04
6.36
6.76
7.02
7.34
7.63
7.61
8.01
8.32
8.82
8.95
9.27
9.49
10.30
10.67
11.13
11.42
12.06
12.52
13.07
12.97
13.48
13.91
14.50
14.77
15.20
15.55
13.54
14.15
14.60
15.37
15.50
15.95
16.24
kW
COOL
CAP.
30
2.35
2.37
2.38
2.40
2.42
2.43
2.45
2.40
2.43
2.47
2.51
2.54
2.58
2.61
2.87
2.90
2.93
2.96
2.98
3.01
3.04
2.77
3.01
3.21
3.47
3.61
3.81
3.98
4.02
4.04
4.05
4.07
4.08
4.10
4.11
4.83
4.84
4.84
4.85
4.86
4.86
4.87
kW
POWER
INPUT
4.01
4.35
4.62
4.98
5.15
5.42
5.58
5.17
5.49
5.80
6.15
6.42
6.72
7.01
6.73
7.10
7.41
7.85
8.04
8.35
8.60
9.58
10.04
10.55
10.95
11.59
12.11
12.69
11.79
12.45
13.05
13.76
14.25
14.85
15.40
12.65
13.31
13.87
14.64
14.97
15.53
15.97
kW
COOL
CAP.
35
2.47
2.50
2.52
2.55
2.55
2.57
2.59
2.54
2.56
2.60
2.59
2.68
2.72
2.78
3.28
3.31
3.35
3.38
3.41
3.44
3.47
3.35
3.48
3.59
3.74
3.81
3.91
4.00
4.46
4.47
4.49
4.50
4.51
4.53
4.54
5.29
5.29
5.30
5.30
5.31
5.31
5.32
kW
POWER
INPUT
3.34
3.59
3.86
4.12
4.31
4.60
4.72
4.78
5.12
5.41
5.79
6.01
6.30
6.56
5.84
6.19
6.50
6.88
7.12
7.43
7.71
8.86
9.40
9.97
10.48
11.12
11.70
12.31
10.61
11.42
12.19
13.02
13.73
14.51
15.25
11.76
12.48
13.13
13.91
14.44
15.10
15.69
kW
COOL
CAP.
40
2.68
2.70
2.72
2.74
2.75
2.77
2.79
2.71
2.75
2.78
2.82
2.86
2.90
2.93
3.69
3.73
3.77
3.80
3.84
3.87
3.91
3.92
3.95
3.97
4.01
4.00
4.02
4.02
4.90
4.91
4.92
4.93
4.94
4.95
4.96
5.74
5.74
5.75
5.75
5.75
5.76
5.76
kW
POWER
INPUT
AMBIENT TEMPERATURE (DB) ON CONDENSER ( °C )
3.11
3.33
3.59
3.83
4.01
4.27
4.38
4.33
4.66
4.94
5.31
5.50
5.78
6.02
5.49
5.82
6.13
6.49
6.76
7.07
7.35
8.57
9.14
9.74
10.29
10.94
11.53
12.15
10.14
11.00
11.84
12.73
13.53
14.37
15.19
10.87
11.64
12.40
13.17
13.91
14.67
15.42
kW
COOL
CAP.
42
2.74
2.76
2.78
2.81
2.82
2.84
2.85
2.86
2.90
2.94
2.98
3.02
3.05
3.09
3.86
3.90
3.93
3.97
4.01
4.04
4.08
4.15
4.14
4.12
4.11
4.08
4.06
4.03
5.07
5.08
5.09
5.10
5.11
5.12
5.13
6.20
6.20
6.20
6.20
6.20
6.21
6.21
kW
POWER
INPUT
2.60
2.78
2.96
3.14
3.33
3.51
3.69
4.28
4.62
4.90
5.29
5.46
5.74
5.96
4.79
5.10
5.40
5.71
6.02
6.33
6.64
7.99
8.63
9.28
9.92
10.56
11.20
11.85
9.20
10.18
11.16
12.13
13.11
14.09
15.07
10.69
11.47
12.25
13.03
13.81
14.58
15.36
kW
COOL
CAP.
46
2.90
2.92
2.93
2.95
2.97
2.99
3.01
2.90
2.95
2.99
3.05
3.06
3.10
3.12
4.19
4.23
4.27
4.31
4.35
4.39
4.43
4.61
4.52
4.42
4.33
4.23
4.14
4.05
5.42
5.43
5.44
5.45
5.46
5.47
5.48
6.29
6.29
6.29
6.29
6.29
6.29
6.30
kW
POWER
INPUT
131
M5AC055CR
M5AC050CR
M5AC040CR
M5AC030CR
M5AC025CR
M5AC020CR
MODEL
35
40
45
50
55
35
40
45
50
55
35
40
45
50
55
35
40
45
50
55
35
40
45
50
55
35
40
45
50
55
2.14
2.37
2.55
2.76
2.91
2.14
2.31
2.49
2.59
2.83
2.37
2.74
3.10
3.46
3.82
2.71
11.00
3.57
4.01
4.45
3.30
3.89
4.47
5.06
5.64
5.01
5.60
6.18
6.76
7.35
kW
kW
2.30
2.24
2.17
2.30
1.78
3.85
3.63
3.62
3.10
2.84
4.69
4.50
4.31
4.12
3.93
6.75
6.11
5.47
4.83
4.19
7.83
7.71
7.59
7.47
7.34
10.12
9.68
9.23
8.78
8.33
POWER
INPUT
HEAT
CAP.
-7
Heatpump- Heating Mode
Refrigerant : R410A
LEAVING WATER TEMP (°C)
4.59
4.34
4.12
3.69
3.57
5.92
5.69
5.26
5.17
4.90
7.43
7.27
7.12
6.96
6.81
9.88
9.42
8.97
8.51
8.05
11.79
11.67
11.55
11.42
11.30
13.68
13.31
12.94
12.57
12.20
kW
HEAT
CAP.
2.30
2.52
2.72
2.89
3.09
2.29
2.48
2.67
2.88
3.04
2.46
2.83
3.20
3.57
3.94
2.90
-4.53
3.75
4.18
4.60
3.41
3.96
4.51
5.06
5.61
5.06
5.64
6.23
6.82
7.41
kW
POWER
INPUT
-5
4.66
4.42
4.21
3.91
3.62
6.00
5.77
5.63
5.25
4.99
7.54
7.38
7.23
7.08
6.93
10.00
9.55
9.10
8.65
8.20
11.95
11.83
11.70
11.58
11.46
13.82
13.45
13.09
12.72
12.36
kW
HEAT
CAP.
0
2.32
2.53
2.73
2.90
3.10
2.29
2.47
2.66
2.85
3.03
2.46
2.83
3.21
3.58
3.95
2.91
1.19
3.76
4.18
4.61
3.41
3.96
4.51
5.06
5.61
5.06
5.65
6.24
6.82
7.41
kW
POWER
INPUT
4.61
4.38
4.17
3.90
3.59
5.96
5.73
5.77
5.21
4.95
7.48
7.33
7.18
7.02
6.87
9.94
9.49
9.04
8.58
8.13
11.88
11.75
11.63
11.51
11.38
13.75
13.38
13.02
12.65
12.28
kW
HEAT
CAP.
4
2.32
2.53
2.73
2.90
3.10
2.28
2.47
2.65
2.84
3.02
2.46
2.83
3.20
3.57
3.95
2.91
5.05
3.75
4.18
4.61
3.41
3.96
4.51
5.06
5.61
5.06
5.65
6.24
6.82
7.41
kW
POWER
INPUT
6.45
6.13
5.84
5.41
5.02
7.68
7.44
7.33
6.93
6.66
9.77
9.64
9.52
9.40
9.27
12.88
12.60
11.95
11.65
11.34
15.18
15.06
14.93
14.81
14.68
16.71
16.41
16.11
15.81
15.51
kW
HEAT
CAP.
7
2.48
2.68
2.89
3.03
3.27
2.40
2.59
2.79
2.99
3.18
2.53
2.91
3.29
3.67
4.05
3.09
3.50
3.90
4.32
4.74
3.50
4.02
4.54
5.06
5.58
5.09
5.69
6.28
6.87
7.47
kW
POWER
INPUT
4.81
4.57
4.35
4.06
3.74
6.14
5.91
5.69
5.39
5.13
7.73
7.58
7.43
7.28
7.13
10.22
9.79
9.35
8.91
8.48
12.23
12.11
11.98
11.86
11.74
14.07
13.71
13.35
12.99
12.63
kW
HEAT
CAP.
AMBIENT TEMPERATURE (DB) ON CONDENSOR (°C)
2.33
2.55
2.74
2.91
3.12
2.30
2.48
2.67
2.85
3.04
2.47
2.84
3.21
3.58
3.96
2.92
13.01
3.77
4.20
4.62
3.42
3.97
4.51
5.06
5.61
5.06
5.65
6.24
6.83
7.42
kW
POWER
INPUT
10
4.66
4.42
4.21
3.93
3.62
6.00
5.77
5.55
5.25
4.99
7.54
7.38
7.23
7.08
6.93
10.00
9.55
9.10
8.65
8.20
11.95
11.83
11.70
11.58
11.46
13.82
13.45
13.09
12.72
12.36
kW
HEAT
CAP.
2.32
2.53
2.73
2.90
3.10
2.29
2.47
2.66
2.84
3.03
2.46
2.83
3.21
3.58
3.95
2.91
11.98
3.76
4.18
4.61
3.41
3.96
4.51
5.06
5.61
5.06
5.65
6.24
6.82
7.41
kW
POWER
INPUT
15
5.26
4.99
4.75
4.40
4.09
5.94
5.71
6.10
5.19
4.93
8.27
8.13
7.99
7.85
7.70
10.85
10.45
10.05
9.65
9.24
13.02
12.90
12.77
12.65
12.52
14.78
14.43
14.09
13.74
13.40
kW
HEAT
CAP.
2.31
2.53
2.73
2.94
3.10
2.32
2.51
2.70
2.89
3.08
2.48
2.86
3.23
3.61
3.98
2.96
14.07
3.81
4.23
4.65
3.44
3.98
4.52
5.06
5.60
5.07
5.66
6.25
6.84
7.43
kW
POWER
INPUT
21
Dimensional Data
Outline and Dimension
80,0
300,0
80,0
English
Model : M4AC/ MAC020 / 025 / 030C/CR, M5AC020 / 025CR
10,0
1181,6
10,0
460,0
85,0
128,5
DRAINAGE
55,2
475,0
789,5
WATER WATER
OUTLET INLET
128,5
All Dimensions are in mm
15,0
1181,6
15,0
79,7
300,0
80,3
Model : M4AC/ MAC040 / 050 / 060C/CR
20,0
460,0
1160,0
878,8
1409,4
WATER WATER
OUTLET INLET
DRAINAGE
85,0
All Dimensions are in mm
132
128,5
Model : M4AC/ MAC080 / 100 / 120 / 150C/CR
D
C
A
L
K
M
I
J
WATER
WA
OUTLET
G
WA
W
ATER
INLET
H E
L
F
B
All Dimensions are in mm
Model
A
B
C
D
E
M4AC/MAC080 C/CR
1500
900
1245
1190
297.5
F
G
Base Leg Hole
307.5
1446
M4AC/MAC100 C/CR
1500
900
1245
1190
297.5
307.5
1446
M4AC/MAC120 C/CR
1800
1150
1245
1190
347.5
416
1776
M4AC/MAC150 C/CR
1800
1150
1245
1190
347.5
416
1776
H
I
J
K
L
M
100
265
385
60
200
170
100
265
385
60
200
170
100
265
385
60
200
170
100
265
385
60
200
170
133
Model : M5AC030CR
1051,6
10,0
10,0
1010,0
22,3
22,3
All Dimensions are in mm
81,4
789,5
479,0
283,3
50,0
WATER
OUTLET
WATER
INLET
147,3 94,2
15,0
1029,0
15,0
406,5
79,4
300,0
80,6
Model : M5AC040 / 050 / 055CR
85,0
70,5
WATER OUT
50,0
724,9
882,9
982,9
WATER IN
70,0
452,0
ELECTRICAL
CABLE
36,5
281,5
All Dimensions are in mm
134
Accessory Hydraulic Kit (Optional)
Hydraulic kit consists of 135L capacity water storage butffer tank, over pressure release value and
drainage point.
Weight
Material of water tank
Pipe Connection
Type of pipes connection
Packing Dimension
= 92kg
= Mild steel with 3mm thickness
= 1 - 1/4”
= BSPF Female
= 838 (W) x 788 (D) x 1378 (H)
The buffer tank is installed at the water return path back to chiller. In order to let the connection look tidy, the
tank has a bypass pipe (the center connection) to allow the pipe to be connected to FCU. The additional
outlets are sealed (they are meant for installation at different side). Please refer to the expleded view.
135
Electrical Data
Electrical Data - R22 Cooling only
MODEL
MAC020C
INSULATION GRADE
POWER SOURCE
CONDENSER FAN
MOTOR
W
135
135
A
0.67
0.67
MOTOR OUTPUT
W
145
145
POLES
6
6
INSULATION GRADE
E
NA
220 - 240 / 1 / 50
V/Ph/Hz
220 - 240 / 1 / 50
CAPACITOR
µF
45
50
RATED INPUT POWER
W
2359
2405
RATED RUNNING CURRENT
A
11.20
11.10
LOCKED ROTOR AMP.
A
67
82
POWER SOURCE
V/Ph/Hz
175
190
A
0.77
0.83
MAC030C
MAC040C
V/Ph/Hz
220 - 240 / 1 / 50
W
135
270
A
0.67
1.34
MOTOR OUTPUT
POLES
W
145
145 x2
6
6
NA
NA
380 - 415 / 3 / 50
V/Ph/Hz
220 - 240 / 1 / 50
CAPACITOR
µF
60
NA
RATED INPUT POWER
W
3155
3880
RATED RUNNING CURRENT
A
15.00
7.60
LOCKED ROTOR AMP.
INSULATION GRADE
A
114
66
POWER SOURCE
V/Ph/Hz
F
F
220 - 240 / 1 / 50
380 - 415 / 3 / 50
RATED INPUT POWER
W
201
320
RATED RUNNING CURRENT
A
0.88
0.71
MAC050C
MAC060C
MODEL
INSULATION GRADE
POWER SOURCE
V/Ph/Hz
F
F
220 - 240 / 1 / 50
220 - 240 / 1 / 50
RATED INPUT POWER
W
270
270
RATED RUNNING CURRENT
A
1.34
1.34
MOTOR OUTPUT
POLES
W
145 x2
145 x2
INSULATION GRADE
POWER SOURCE
WATER PUMP
F
220 - 240 / 1 / 50
RATED RUNNING CURRENT
POWER SOURCE
COMPRESSOR
F
RATED INPUT POWER
INSULATION GRADE
CONDENSER FAN
MOTOR
220 - 240 / 1 / 50
W
POWER SOURCE
WATER PUMP
F
220 - 240 / 1 / 50
RATED RUNNING CURRENT
INSULATION GRADE
COMPRESSOR
F
RATED INPUT POWER
MODEL
CONDENSER FAN
MOTOR
F
220 - 240 / 1 / 50
RATED RUNNING CURRENT
INSULATION GRADE
WATER PUMP
F
220 - 240 / 1 / 50
RATED INPUT POWER
POWER SOURCE
COMPRESSOR
V/Ph/Hz
MAC025C
6
6
NA
NA
380 - 415 / 3 / 50
V/Ph/Hz
380 - 415 / 3 / 50
CAPACITOR
µF
NA
NA
RATED INPUT POWER
W
4630
5740
RATED RUNNING CURRENT
A
8.10
11.10
LOCKED ROTOR AMP.
INSULATION GRADE
A
74
101
POWER SOURCE
V/Ph/Hz
F
F
380 - 415 / 3 / 50
380 - 415 / 3 / 50
RATED INPUT POWER
W
345
351
RATED RUNNING CURRENT
A
0.77
0.78
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.
136
Electrical Data - R22 Cooling only
MODEL
MAC080C
INSULATION GRADE
POWER SOURCE
CONDENSER FAN
MOTOR
V/Ph/Hz
W
565
565
A
2.40
2.40
MOTOR OUTPUT
W
120 x2
120 x2
POWER SOURCE
NA
380 - 415 / 3 / 50
380 - 415 / 3 / 50
µF
NA
NA
RATED INPUT POWER
W
7052
8560
RATED RUNNING CURRENT
A
14.00
14.70
LOCKED ROTOR AMP. (COMP1/COMP2)
A
66 / 66
74 / 74
F
F
V/Ph/Hz
380 - 415 / 3 / 50
380 - 415 / 3 / 50
RATED INPUT POWER
W
1050
1050
RATED RUNNING CURRENT
A
1.50
1.50
MAC120C
MAC150C
POWER SOURCE
INSULATION GRADE
POWER SOURCE
V/Ph/Hz
F
F
220 - 240 / 1 / 50
220 - 240 / 1 / 50
1532
RATED INPUT POWER
W
772
RATED RUNNING CURRENT
A
3.60
6.80
MOTOR OUTPUT
POLES
W
200 x2
450 x2
INSULATION GRADE
POWER SOURCE
WATER PUMP
8
NA
V/Ph/Hz
MODEL
COMPRESSOR
8
CAPACITOR
INSULATION GRADE
CONDENSER FAN
MOTOR
F
220 - 240 / 1 / 50
RATED RUNNING CURRENT
INSULATION GRADE
WATER PUMP
F
220 - 240 / 1 / 50
RATED INPUT POWER
POLES
COMPRESSOR
MAC100C
8
6
NA
NA
380 - 415 / 3 / 50
V/Ph/Hz
380 - 415 / 3 / 50
CAPACITOR
µF
NA
NA
RATED INPUT POWER
W
9433
11447
RATED RUNNING CURRENT
A
19.70
22.40
LOCKED ROTOR AMP. (COMP1/COMP2)
INSULATION GRADE
A
101 / 101
95 / 95
F
F
V/Ph/Hz
380 - 415 / 3 / 50
380 - 415 / 3 / 50
POWER SOURCE
RATED INPUT POWER
W
800
800
RATED RUNNING CURRENT
A
2.00
2.00
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.
137
Electrical Data - R22 Heat pump
MODEL
CONDENSER FAN
MOTOR
COMPRESSOR
WATER PUMP
INSULATION GRADE
POWER SOURCE
RATED INPUT POWER
RATED RUNNING CURRENT
MOTOR OUTPUT
POLES
INSULATION GRADE
POWER SOURCE
CAPACITOR
RATED INPUT POWER (COOLING)
RATED INPUT POWER (HEATING)
RATED RUNNING CURRENT (COOLING)
RATED RUNNING CURRENT (HEATING)
LOCKED ROTOR AMP.
INSULATION GRADE
POWER SOURCE
RATED INPUT POWER (COOLING)
RATED INPUT POWER (HEATING)
RATED RUNNING CURRENT (COOLING)
RATED RUNNING CURRENT (HEATING)
V/Ph/Hz
W
A
W
V/Ph/Hz
µF
W
W
A
A
A
V/Ph/Hz
W
W
A
A
MODEL
CONDENSER FAN
MOTOR
COMPRESSOR
WATER PUMP
INSULATION GRADE
POWER SOURCE
RATED INPUT POWER
RATED RUNNING CURRENT
MOTOR OUTPUT
POLES
INSULATION GRADE
POWER SOURCE
CAPACITOR
RATED INPUT POWER (COOLING)
RATED INPUT POWER (HEATING)
RATED RUNNING CURRENT (COOLING)
RATED RUNNING CURRENT (HEATING)
LOCKED ROTOR AMP.
INSULATION GRADE
POWER SOURCE
RATED INPUT POWER (COOLING)
RATED INPUT POWER (HEATING)
RATED RUNNING CURRENT (COOLING)
RATED RUNNING CURRENT (HEATING)
V/Ph/Hz
W
A
W
V/Ph/Hz
µF
W
W
A
A
A
V/Ph/Hz
W
W
A
A
MODEL
CONDENSER FAN
MOTOR
COMPRESSOR
WATER PUMP
INSULATION GRADE
POWER SOURCE
RATED INPUT POWER
RATED RUNNING CURRENT
MOTOR OUTPUT
POLES
INSULATION GRADE
POWER SOURCE
CAPACITOR
RATED INPUT POWER (COOLING)
RATED INPUT POWER (HEATING)
RATED RUNNING CURRENT (COOLING)
RATED RUNNING CURRENT (HEATING)
LOCKED ROTOR AMP.
INSULATION GRADE
POWER SOURCE
RATED INPUT POWER (COOLING)
RATED INPUT POWER (HEATING)
RATED RUNNING CURRENT (COOLING)
RATED RUNNING CURRENT (HEATING)
V/Ph/Hz
W
A
W
V/Ph/Hz
µF
W
W
A
A
A
V/Ph/Hz
W
W
A
A
MAC020CR
MAC025CR
F
220 - 240 / 1 / 50
135
0.67
145
6
E
220 - 240 / 1 / 50
45
2289
2379
10.90
11.20
67
F
220 - 240 / 1 / 50
175
186
0.77
0.82
F
220 - 240 / 1 / 50
135
0.67
145
6
NA
220 - 240 / 1 / 50
50
2455
2285
11.20
10.50
82
F
220 - 240 / 1 / 50
189
194
0.83
0.85
MAC030CR
MAC040CR
F
220 - 240 / 1 / 50
135
0.67
145
6
NA
220 - 240 / 1 / 50
60
3205
3215
16.7
16.8
114
F
220 - 240 / 1 / 50
201
211
0.88
0.93
F
220 - 240 / 1 / 50
270
1.34
145 x2
6
NA
380 - 415 / 3 / 50
NA
3970
4030
7.4
7.6
66
F
380 - 415 / 3 / 50
320
329
0.71
0.73
MAC050CR
MAC060CR
F
220 - 240 / 1 / 50
270
1.34
145 x2
6
NA
380 - 415 / 3 / 50
NA
4440
4380
7.7
7.7
74
F
380 - 415 / 3 / 50
336
349
0.75
0.77
F
220 - 240 / 1 / 50
270
1.34
145 x2
6
NA
380 - 415 / 3 / 50
NA
5930
5620
12.2
11.8
101
F
380 - 415 / 3 / 50
351
357
0.78
0.79
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.
138
Electrical Data - R22 Heat pump
MODEL
MAC080CR
INSULATION GRADE
POWER SOURCE
CONDENSER FAN
MOTOR
V/Ph/Hz
W
565
565
A
2.40
2.40
MOTOR OUTPUT
W
120 x2
120 x2
NA
380 - 415 / 3 / 50
380 - 415 / 3 / 50
µF
NA
NA
RATED INPUT POWER (COOLING)
W
7962
9190
RATED INPUT POWER (HEATING)
W
7714
8694
RATED RUNNING CURRENT (COOLING)
A
14.00
16.00
RATED RUNNING CURRENT (HEATING)
A
13.40
15.10
LOCKED ROTOR AMP. (COMP1/COMP2)
A
66 / 66
74 / 74
F
F
V/Ph/Hz
380 - 415 / 3 / 50
380 - 415 / 3 / 50
RATED INPUT POWER (COOLING)
W
1050
1050
RATED INPUT POWER (HEATING)
W
1050
1050
RATED RUNNING CURRENT (COOLING)
A
1.50
1.50
RATED RUNNING CURRENT (HEATING)
A
1.50
1.50
MAC120CR
MAC150CR
POWER SOURCE
MODEL
INSULATION GRADE
POWER SOURCE
V/Ph/Hz
F
F
220 - 240 / 1 / 50
220 - 240 / 1 / 50
1532
RATED INPUT POWER
W
772
RATED RUNNING CURRENT
A
3.60
6.80
MOTOR OUTPUT
POLES
W
200 x2
450 x2
INSULATION GRADE
POWER SOURCE
8
6
NA
NA
380 - 415 / 3 / 50
V/Ph/Hz
380 - 415 / 3 / 50
CAPACITOR
µF
NA
NA
RATED INPUT POWER (COOLING)
W
10142
11549
RATED INPUT POWER (HEATING)
W
10376
12240
RATED RUNNING CURRENT (COOLING)
A
20.5
22.0
RATED RUNNING CURRENT (HEATING)
A
20.6
23.0
LOCKED ROTOR AMP. (COMP1/COMP2)
INSULATION GRADE
A
101 / 101
95 / 95
F
F
V/Ph/Hz
380 - 415 / 3 / 50
380 - 415 / 3 / 50
RATED INPUT POWER (COOLING)
W
800
800
RATED INPUT POWER (HEATING)
W
800
800
RATED RUNNING CURRENT (COOLING)
A
2.00
2.00
RATED RUNNING CURRENT (HEATING)
A
2.00
2.00
POWER SOURCE
WATER PUMP
8
NA
V/Ph/Hz
INSULATION GRADE
COMPRESSOR
8
CAPACITOR
POWER SOURCE
CONDENSER FAN
MOTOR
220 - 240 / 1 / 50
RATED RUNNING CURRENT
INSULATION GRADE
WATER PUMP
F
220 - 240 / 1 / 50
RATED INPUT POWER
POLES
COMPRESSOR
MAC100CR
F
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.
139
Electrical Data - R407C Cooling only
MODEL
M4AC020C
INSULATION GRADE
POWER SOURCE
CONDENSER FAN
MOTOR
W
135
135
A
0.67
0.67
MOTOR OUTPUT
W
145
145
POLES
6
6
INSULATION GRADE
E
NA
220 - 240 / 1 / 50
V/Ph/Hz
220 - 240 / 1 / 50
CAPACITOR
µF
50
50
RATED INPUT POWER
W
2299
2625
RATED RUNNING CURRENT
A
11.00
12.10
LOCKED ROTOR AMP.
A
58
82
POWER SOURCE
V/Ph/Hz
183
189
A
0.80
0.83
M4AC030C
M4AC040C
V/Ph/Hz
W
135
270
A
0.67
1.34
MOTOR OUTPUT
POLES
W
145
145 x2
6
6
NA
NA
380 - 415 / 3 / 50
V/Ph/Hz
220 - 240 / 1 / 50
CAPACITOR
µF
60
NA
RATED INPUT POWER
W
3345
4320
RATED RUNNING CURRENT
A
15.90
8.10
LOCKED ROTOR AMP.
INSULATION GRADE
A
114
66
POWER SOURCE
V/Ph/Hz
F
F
220 - 240 / 1 / 50
380 - 415 / 3 / 50
RATED INPUT POWER
W
199
320
RATED RUNNING CURRENT
A
0.87
0.71
M4AC050C
M4AC060C
MODEL
INSULATION GRADE
POWER SOURCE
V/Ph/Hz
F
F
220 - 240 / 1 / 50
220 - 240 / 1 / 50
RATED INPUT POWER
W
270
270
RATED RUNNING CURRENT
A
1.34
1.34
MOTOR OUTPUT
POLES
W
145 x2
145 x2
INSULATION GRADE
POWER SOURCE
WATER PUMP
F
220 - 240 / 1 / 50
RATED RUNNING CURRENT
POWER SOURCE
COMPRESSOR
F
220 - 240 / 1 / 50
RATED INPUT POWER
INSULATION GRADE
CONDENSER FAN
MOTOR
220 - 240 / 1 / 50
W
INSULATION GRADE
WATER PUMP
F
220 - 240 / 1 / 50
RATED RUNNING CURRENT
POWER SOURCE
COMPRESSOR
F
RATED INPUT POWER
MODEL
CONDENSER FAN
MOTOR
220 - 240 / 1 / 50
RATED RUNNING CURRENT
INSULATION GRADE
WATER PUMP
F
220 - 240 / 1 / 50
RATED INPUT POWER
POWER SOURCE
COMPRESSOR
V/Ph/Hz
M4AC025C
F
6
6
NA
NA
380 - 415 / 3 / 50
V/Ph/Hz
380 - 415 / 3 / 50
CAPACITOR
µF
NA
NA
RATED INPUT POWER
W
5340
6240
RATED RUNNING CURRENT
A
9.00
11.70
LOCKED ROTOR AMP.
INSULATION GRADE
A
74
101
POWER SOURCE
V/Ph/Hz
F
F
380 - 415 / 3 / 50
380 - 415 / 3 / 50
RATED INPUT POWER
W
345
349
RATED RUNNING CURRENT
A
0.77
0.77
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.
140
Electrical Data - R407C Cooling only
MODEL
M4AC080C
INSULATION GRADE
POWER SOURCE
CONDENSER FAN
MOTOR
V/Ph/Hz
W
565
565
A
2.40
2.40
MOTOR OUTPUT
W
120 x2
120 x2
POWER SOURCE
NA
380 - 415 / 3 / 50
380 - 415 / 3 / 50
µF
NA
NA
RATED INPUT POWER
W
7848
9156
RATED RUNNING CURRENT
A
15.00
15.70
LOCKED ROTOR AMP. (COMP1/COMP2)
A
66 / 66
74 / 74
F
F
V/Ph/Hz
380 - 415 / 3 / 50
380 - 415 / 3 / 50
RATED INPUT POWER
W
1050
1050
RATED RUNNING CURRENT
A
1.50
1.50
M4AC120C
M4AC150C
POWER SOURCE
INSULATION GRADE
POWER SOURCE
V/Ph/Hz
F
F
220 - 240 / 1 / 50
220 - 240 / 1 / 50
1532
RATED INPUT POWER
W
772
RATED RUNNING CURRENT
A
3.60
6.80
MOTOR OUTPUT
POLES
W
200 x2
450 x2
INSULATION GRADE
POWER SOURCE
WATER PUMP
8
NA
V/Ph/Hz
MODEL
COMPRESSOR
8
CAPACITOR
INSULATION GRADE
CONDENSER FAN
MOTOR
F
220 - 240 / 1 / 50
RATED RUNNING CURRENT
INSULATION GRADE
WATER PUMP
F
220 - 240 / 1 / 50
RATED INPUT POWER
POLES
COMPRESSOR
M4AC100C
8
6
NA
NA
380 - 415 / 3 / 50
V/Ph/Hz
380 - 415 / 3 / 50
CAPACITOR
µF
NA
NA
RATED INPUT POWER
W
10233
12199
RATED RUNNING CURRENT
A
20.40
23.60
LOCKED ROTOR AMP. (COMP1/COMP2)
INSULATION GRADE
A
101 / 101
95 / 95
F
F
V/Ph/Hz
380 - 415 / 3 / 50
380 - 415 / 3 / 50
POWER SOURCE
RATED INPUT POWER
W
800
800
RATED RUNNING CURRENT
A
2.00
2.00
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.
141
Electrical Data - R407C Heat pump
MODEL
CONDENSER FAN
MOTOR
COMPRESSOR
WATER PUMP
INSULATION GRADE
POWER SOURCE
RATED INPUT POWER
RATED RUNNING CURRENT
MOTOR OUTPUT
POLES
INSULATION GRADE
POWER SOURCE
CAPACITOR
RATED INPUT POWER (COOLING)
RATED INPUT POWER (HEATING)
RATED RUNNING CURRENT (COOLING)
RATED RUNNING CURRENT (HEATING)
LOCKED ROTOR AMP.
INSULATION GRADE
POWER SOURCE
RATED INPUT POWER (COOLING)
RATED INPUT POWER (HEATING)
RATED RUNNING CURRENT (COOLING)
RATED RUNNING CURRENT (HEATING)
V/Ph/Hz
W
A
W
V/Ph/Hz
µF
W
W
A
A
A
V/Ph/Hz
W
W
A
A
MODEL
CONDENSER FAN
MOTOR
COMPRESSOR
WATER PUMP
INSULATION GRADE
POWER SOURCE
RATED INPUT POWER
RATED RUNNING CURRENT
MOTOR OUTPUT
POLES
INSULATION GRADE
POWER SOURCE
CAPACITOR
RATED INPUT POWER (COOLING)
RATED INPUT POWER (HEATING)
RATED RUNNING CURRENT (COOLING)
RATED RUNNING CURRENT (HEATING)
LOCKED ROTOR AMP.
INSULATION GRADE
POWER SOURCE
RATED INPUT POWER (COOLING)
RATED INPUT POWER (HEATING)
RATED RUNNING CURRENT (COOLING)
RATED RUNNING CURRENT (HEATING)
V/Ph/Hz
W
A
W
V/Ph/Hz
µF
W
W
A
A
A
V/Ph/Hz
W
W
A
A
MODEL
CONDENSER FAN
MOTOR
COMPRESSOR
WATER PUMP
INSULATION GRADE
POWER SOURCE
RATED INPUT POWER
RATED RUNNING CURRENT
MOTOR OUTPUT
POLES
INSULATION GRADE
POWER SOURCE
CAPACITOR
RATED INPUT POWER (COOLING)
RATED INPUT POWER (HEATING)
RATED RUNNING CURRENT (COOLING)
RATED RUNNING CURRENT (HEATING)
LOCKED ROTOR AMP.
INSULATION GRADE
POWER SOURCE
RATED INPUT POWER (COOLING)
RATED INPUT POWER (HEATING)
RATED RUNNING CURRENT (COOLING)
RATED RUNNING CURRENT (HEATING)
V/Ph/Hz
W
A
W
V/Ph/Hz
µF
W
W
A
A
A
V/Ph/Hz
W
W
A
A
M4AC020CR
M4AC025CR
F
220 - 240 / 1 / 50
135
0.67
145
6
E
220 - 240 / 1 / 50
50
2289
2369
11.20
11.50
58
F
220 - 240 / 1 / 50
173
181
0.76
0.79
F
220 - 240 / 1 / 50
135
0.67
145
6
F
220 - 240 / 1 / 50
50
2755
2415
12.80
12.60
82
F
220 - 240 / 1 / 50
186
195
0.82
0.86
M4AC030CR
M4AC040CR
F
220 - 240 / 1 / 50
135
0.67
145
6
NA
220 - 240 / 1 / 50
60
3475
3655
17.7
18.4
114
F
220 - 240 / 1 / 50
194
214
0.85
0.94
F
220 - 240 / 1 / 50
270
1.34
145 x2
6
NA
380 - 415 / 3 / 50
NA
4230
4390
7.9
8.0
66
F
380 - 415 / 3 / 50
320
334
0.71
0.74
M4AC050CR
M4AC060CR
F
220 - 240 / 1 / 50
270
1.34
145 x2
6
NA
380 - 415 / 3 / 50
NA
4840
5030
8.3
8.6
74
F
380 - 415 / 3 / 50
336
347
0.75
0.77
F
220 - 240 / 1 / 50
270
1.34
145 x2
6
NA
380 - 415 / 3 / 50
NA
5890
5640
11.5
11.4
101
F
380 - 415 / 3 / 50
347
358
0.77
0.79
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.
142
Electrical Data - R407C Heat pump
MODEL
M4AC080CR
INSULATION GRADE
POWER SOURCE
CONDENSER FAN
MOTOR
W
565
565
A
2.40
2.40
MOTOR OUTPUT
W
120 x2
120 x2
POLES
8
8
INSULATION GRADE
E
F
380 - 415 / 3 / 50
V/Ph/Hz
380 - 415 / 3 / 50
CAPACITOR
µF
NA
NA
RATED INPUT POWER (COOLING)
W
8331
9413
RATED INPUT POWER (HEATING)
W
8360
9519
RATED RUNNING CURRENT (COOLING)
A
14.10
16.20
RATED RUNNING CURRENT (HEATING)
A
14.50
16.20
LOCKED ROTOR AMP. (COMP1/COMP2)
A
66 / 66
74 / 74
F
F
V/Ph/Hz
380 - 415 / 3 / 50
380 - 415 / 3 / 50
RATED INPUT POWER (COOLING)
W
1050
1050
RATED INPUT POWER (HEATING)
W
1050
1050
RATED RUNNING CURRENT (COOLING)
A
1.50
1.50
RATED RUNNING CURRENT (HEATING)
A
1.50
1.50
M4AC120CR
M4AC150CR
INSULATION GRADE
MODEL
INSULATION GRADE
POWER SOURCE
CONDENSER FAN
MOTOR
V/Ph/Hz
F
220 - 240 / 1 / 50
220 - 240 / 1 / 50
1532
RATED INPUT POWER
W
772
A
3.60
6.80
MOTOR OUTPUT
POLES
W
200 x2
450 x2
POWER SOURCE
8
6
NA
NA
380 - 415 / 3 / 50
V/Ph/Hz
380 - 415 / 3 / 50
CAPACITOR
µF
NA
NA
RATED INPUT POWER (COOLING)
W
10701
12819
RATED INPUT POWER (HEATING)
W
10814
13492
RATED RUNNING CURRENT (COOLING)
A
21.0
23.5
RATED RUNNING CURRENT (HEATING)
A
20.6
24.7
LOCKED ROTOR AMP. (COMP1/COMP2)
INSULATION GRADE
A
101 / 101
95 / 95
F
F
V/Ph/Hz
380 - 415 / 3 / 50
380 - 415 / 3 / 50
RATED INPUT POWER (COOLING)
W
800
800
RATED INPUT POWER (HEATING)
W
800
800
RATED RUNNING CURRENT (COOLING)
A
2.00
2.00
RATED RUNNING CURRENT (HEATING)
A
2.00
2.00
POWER SOURCE
WATER PUMP
F
RATED RUNNING CURRENT
INSULATION GRADE
COMPRESSOR
F
220 - 240 / 1 / 50
RATED RUNNING CURRENT
POWER SOURCE
WATER PUMP
F
220 - 240 / 1 / 50
RATED INPUT POWER
POWER SOURCE
COMPRESSOR
V/Ph/Hz
M4AC100CR
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.
143
Electrical Data - R410A Heat pump
MODEL
CONDENSER FAN
MOTOR
COMPRESSOR
WATER PUMP
INSULATION GRADE
POWER SOURCE
RATED INPUT POWER
RATED RUNNING CURRENT
MOTOR OUTPUT
POLES
INSULATION GRADE
POWER SOURCE
CAPACITOR
RATED INPUT POWER (COOLING)
RATED INPUT POWER (HEATING)
RATED RUNNING CURRENT (COOLING)
RATED RUNNING CURRENT (HEATING)
LOCKED ROTOR AMP.
INSULATION GRADE
POWER SOURCE
RATED INPUT POWER (COOLING)
RATED INPUT POWER (HEATING)
RATED RUNNING CURRENT (COOLING)
RATED RUNNING CURRENT (HEATING)
V/Ph/Hz
W
A
W
V/Ph/Hz
µF
W
W
A
A
A
V/Ph/Hz
W
W
A
A
MODEL
CONDENSER FAN
MOTOR
COMPRESSOR
WATER PUMP
INSULATION GRADE
POWER SOURCE
RATED INPUT POWER
RATED RUNNING CURRENT
MOTOR OUTPUT
POLES
INSULATION GRADE
POWER SOURCE
CAPACITOR (COMP1/COMP2)
RATED INPUT POWER (COOLING)
RATED INPUT POWER (HEATING)
RATED RUNNING CURRENT (COOLING)
RATED RUNNING CURRENT (HEATING)
LOCKED ROTOR AMP. (COMP1/COMP2)
INSULATION GRADE
POWER SOURCE
RATED INPUT POWER (COOLING)
RATED INPUT POWER (HEATING)
RATED RUNNING CURRENT (COOLING)
RATED RUNNING CURRENT (HEATING)
V/Ph/Hz
W
A
W
V/Ph/Hz
µF
W
W
A
A
A
V/Ph/Hz
W
W
A
A
MODEL
CONDENSER FAN
MOTOR
COMPRESSOR
WATER PUMP
INSULATION GRADE
POWER SOURCE
RATED INPUT POWER
RATED RUNNING CURRENT
MOTOR OUTPUT
POLES
INSULATION GRADE
POWER SOURCE
CAPACITOR (COMP1/COMP2)
RATED INPUT POWER (COOLING)
RATED INPUT POWER (HEATING)
RATED RUNNING CURRENT (COOLING)
RATED RUNNING CURRENT (HEATING)
LOCKED ROTOR AMP. (COMP1/COMP2)
INSULATION GRADE
POWER SOURCE
RATED INPUT POWER (COOLING)
RATED INPUT POWER (HEATING)
RATED RUNNING CURRENT (COOLING)
RATED RUNNING CURRENT (HEATING)
V/Ph/Hz
W
A
W
V/Ph/Hz
µF
W
W
A
A
A
V/Ph/Hz
W
W
A
A
M5AC020CR
M5AC025CR
F
220 - 240 / 1 / 50
135
0.67
145
6
E
220 - 240 / 1 / 50
45
2230
2262
10.40
10.50
67
F
220 - 240 / 1 / 50
185
193
0.82
0.85
F
220 - 240 / 1 / 50
135
0.67
145
6
E
220 - 240 / 1 / 50
50
2430
2446
11.20
11.30
68
F
220 - 240 / 1 / 50
195
209
0.86
0.91
M5AC030CR
M5AC040CR
F
220 - 240 / 1 / 50
135
0.67
145
6
E
220 - 240 / 1 / 50
50 / 50
3375
3285
15.1
14.7
35 / 35
F
220 - 240 / 1 / 50
210
210
0.92
0.92
F
220 - 240 / 1 / 50
270
1.34
145 x2
6
E
220 - 240 / 1 / 50
50 / 45
3740
3900
17.4
18.1
35 / 67
F
220 - 240 / 1 / 50
320
320
1.59
1.59
M5AC050CR
M5AC055CR
F
220 - 240 / 1 / 50
270
1.34
145 x2
6
E
220 - 240 / 1 / 50
60 / 50
4500
4540
20.1
20.6
58 / 68
F
220 - 240 / 1 / 50
320
320
1.59
1.59
F
220 - 240 / 1 / 50
270
1.34
145 x2
6
E
220 - 240 / 1 / 50
50 / 50
5300
5400
24.4
24.8
68 / 68
F
220 - 240 / 1 / 50
320
320
1.59
1.59
1) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
2) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151.
144
Wiring Diagrams
Model : M4AC/ MAC020C
145
Model : M4AC/ MAC025 / 030C
146
147
S
T
N
380-415/3pH/50Hz
TB1 R
W_PUMP
BOILER
AUX-H
COM1
COM2
LIVE
12V
F02
F01
LP2
LP1
HP2
HP1
CO2
CO1
FLOW
PO
ALM
DE2
DE1
C/H
ON/OFF
OUT_FAN2
CN6
ALM_OUT
ALM_IN
A_FREEZE
4WV1
OUT_FAN1
4WV2
TB2 12V 12V 12V N1
WI WO OA CD1CD2 DF1 DF2
LP
HP
N1 N1 N1
1
FL
H
T
R
OFF
COOL
ON
HEAT
O/F C/H 4WV HTR
2
ENTERING WATER SENSOR
LEAVING WATER SENSOR
OUTDOOR AIR TEMP SENSOR
COMP DISCHARGE SENSOR (1)
AL AL
IN OUT
L N C
OF 2
1A
2A
L N C
A
B
OF 1
CAP
C
OF 1
A
B
OF 2
CAP
C
TB3 OF IN OF OUT
4B
5B
FUSE
10A
SWITCH
N
42
32
31
COMP.
95
41
C O/L
96
U VW
E
PUMP
95
98
PUMP
P O/L
96
English
PART NO : 50 13 4 076741
P
COMP
98
71
U V WE
81
PHASE
PROTECTOR
N R S T
Model : M4AC/ MAC040 / 050 / 060C
Model : M4AC/ MAC080 / 100C (With Isolated Switch)
148
Model : M4AC / MAC 120/ 150C (With Isolated Switch)
149
Model : M4AC/ MAC080 / 100C (With Terminal Block)
150
Model : M4AC / MAC 120 / 150C (With Terminal Block)
151
Model : M4AC020CR
152
Model : M4AC / MAC 025 / 030CR
153
154
S
T
N
380-415/3pH/50Hz
TB1 R
W_PUMP
BOILER
AUX-H
COM1
COM2
LIVE
12V
F02
F01
LP2
LP1
HP2
HP1
C02
C01
FLOW
PO
ALM
DE2
DE1
C/H
ON/OFF
OUT_FAN2
CN6
ALM_OUT
ALM_IN
A_FREEZE
4WV2
4WV1
OUT_FAN1
DEFROST SENSOR (1)
LP
HP
1
FL
ON
2
4WV
OFF
HEAT
COOL
H
T
R
O/F C/H 4WV HTR
ENTERING WATER SENSOR
LEAVING WATER SENSOR
OUTDOOR AIR TEMP SENSOR
COMP DISCHARGE SENSOR (1)
TB2 12V 12V 12V N1 N1 N1 N1
WI WO OA CD1 CD2 DF1 DF2
AL AL
IN OUT
7
7
TB3 OF IN OF OUT
2A
U V WE
COMP.
L N C
45
COMP
44
96
C O/L
E
PUMP
U VW
95
98
PUMP
96
P O/L
PART NO : 50 13 4 076742
95
98
OF 2
1A
32
31
71
L N C
4B
5B
FUSE
10A
81
PHASE
PROTECTOR
N R S T
OF 1
8
1 R 2
E
3 L 4
A
5 Y 6
R2
A
B
OF 1
CAP
C
8
A
B
OF 2
CAP
C
1 R 2
E
3 L 4
A
5 Y 6
R1
SWITCH
N
Model : M4AC / MAC 040 / 050 / 060CR
Model : M4AC / MAC 080 / 100CR (With Isolated Switch)
155
Model : M4AC / MAC 120 / 150CR (With Isolated Switch)
156
Model : M4AC / MAC 080 / 100CR (With Terminal Block)
157
Model : M4AC / MAC 120 / 150CR (With Terminal Block)
158
Model : M5AC020 / 025CR
159
6
1
160
COMP R
1
S COMP 1 R
CAP R
5
S COMP 2 R
CAP R
6
5
COMP R
2
C S
1
4
L N
PUMP
SWITCH
1A
OF 1
C
OF 1
CAP
TB3 OF IN OF OUT
A
B
FL
HP
LP
4WV
N
COM2
LIVE
POWER RELAY
COMP 1
COOL
HEAT
ON
OFF
12V 12V N1 N1 N1 N1 C/H O/F
1
H
T
R
P 4WV HTR
CN6
2
OUT_FAN2
2A
CNL
4B
AL AL TB2
IN OUT
ENTERING WATER SENSOR
LEAVING WATER SENSOR
OUTDOOR AIR TEMP SENSOR
COMP DISCHARGE SENSOR (1)
COMP DISCHARGE SENSOR (2)
DEFROST SENSOR (1)
PART NO : 5013 4 076380
WI WO OA CD1CD2 DF1DF2
OUT_FAN1
5B
COM1
8
7
AUX-H
8
7
4WV1
FUSE
10A
BOILER
1R 2
E
3L 4
A
5Y 6
R2
W_PUMP
12V
F02
F01
LP2
LP1
HP2
HP1
C02
C01
FLOW
PO
ALM
DE2
DE1
C/H
ON/OFF
1 R2
E
3 L 4
A
5 Y 6
R1
4WV2
N
4
C S
T
A_FREEZE
S
ALM_IN
TB1 R
ALM_OUT
380-420/3PH-N/50Hz
Model : M5AC030CR
POWER RELAY
COMP 2
161
POWER RELAY
COMP 1
C S
S COMP 1 R
CAP R
6
5
C S
5
S COMP 2 R
CAP R
6
COMP R
2
1
4
8
7
8
POWER RELAY
COMP 2
7
PUMP
L N
OF 1
CAP
OF 2
CAP
C
C
41
TB3 OF IN OF OUT
OF 2
L NC
A
B
A
B
FL
HP
LP
4WV
N
12V 12V N1 N1
LIVE
COOL
HEAT
ON
OFF
N1 N1 C/H O/F
COM2
2A
1A
L NC
SWITCH
OF 1
4B
1
H
T
R
AL AL
IN OUT TB2
P 4WV HTR
CN6
2
OUT_FAN2
5B
LEAVING WATER SENSOR
ENTERING WATER SENSOR
OUTDOOR AIR TEMP SENSOR
COMP DISCHARGE SENSOR (1)
COMP DISCHARGE SENSOR (2)
DEFROST SENSOR (1)
PART NO : 5013 4 076381
WI WO OA CD1CD2 DF1DF2
4WV2
FUSE
10A
COM1
1 R2
E
3 L 4
A
5 Y 6
R2
BOILER
1 R2
E
3 L 4
A
5 Y 6
R1
4WV1
N
COMP R
1
1
4
T
A_FREEZE
S
OUT_FAN1
ALM_IN
TB1 R
AUX-H
12V
F02
F01
LP2
LP1
HP2
HP1
C02
C01
FLOW
PO
ALM
DE2
DE1
C/H
ON/OFF
ALM_OUT
380-420/3PH-N/50Hz
Model : M5AC040 / 050 / 055CR
W_PUMP
Servicing And Maintenance
Servicing
Servicing or maintenance of these unit must be carried out by experienced personnel with specific
training in refrigeration. Repeated check the safety devices and continuous cycling of control components
must be analyzed and corrected before being reset.
The simple design of the refrigeration circuit totally eliminates potential problems during normal unit
operation. No maintenance work is needed on the refrigeration circuit as long as the unit is operating
normally.
Ease of maintenance has been taken into consideration during the design stage such that the unit is easily
accessible for servicing and maintenance. By accessing from the front panel of the unit, servicing and
maintenance operation can be done easily. The electrical components are especially easy to access since
it is located in the terminal box on top of the front panel.
Under normal circumstances, these chiller require only a check and cleaning of air intake through the coil
surface only. These can be done monthly or quarterly depending on the surrounding where the units are
installed.
When the surrounding is very oily or dusty, then the coils must be regularly cleaned by a qualified air
conditioner service technician to ensure sufficient cooling capacity and efficient unit operation. The
normal life span might be shortened if no proper service is provided.
Maintenance
For consistent performance and durability, always conduct proper and regular maintenance to the unit.
For prolong period of operation time, the heat exchanger will become dirty impairing its effectiveness and
reducing the performance of the units. Consult your local dealer about the cleaning of the heat exchanger.
No major maintenance or servicing needed for the internal water circuit in the unit except the water pump
failure. It is advised that regular check on the filter to be conducted and change the water filter if the filter
is dirty or choked.
Always check the water level in the system, in order to protect the moving components in the hydraulic kit
from over heating and excessive wear.
162
Troubleshooting
When any malfunction is occurred, immediately switch off the power supply to the unit, and contact the
local dealer, if necessary. Some simple troubleshooting tips are given below:
SYMPTONS
1. Compressor does
not start.
PROBLEM CAUSES
• No power supply.
• Fuses blown or automatic circuit
break down open.
2. Fan does not work.
3. Unit does work, but
insufficient cooling.
•
•
Defective contactor or coil.
Unit is stopped because safety
device has tripped.
•
Loose wires.
•
Compressor faulty.
•
•
•
•
•
No power supply.
Fan motor faulty.
Thermostats setting too high.
Condenser coil dirty.
Obstacle blocking air inlet or
outlet of the unit.
Insufficient refrigerant in the
system.
Improper water flow rate,
Water in the system is
contaminated.
No water in the system.
Low water level in the system.
•
•
•
•
•
4. Flow switch error.
REMEDIAL ACTION
• Check power supply.
• Look for short circuit or grounded
wires in motor windings. Replace
fuses and reset circuit breakers
when the fault has been corrected.
Check tightness and soundness of
all electrical connections.
• Repair or replace.
• Determine the type of safety shut
down and correct the default before
the unit is restarted.
• Check wire connections and
tighten terminal screws.
• Contact local dealer.
•
•
•
•
•
Check power supply.
Contact local dealer
Reset thermostat.
Contact local dealer.
Remove obstacles.
•
Contact local dealer.
•
•
Contact local dealer.
Contact local dealer.
•
•
Check water supply.
Check water supply.
Phase Proctector (Optional)
The unit with Scroll Compressor can only rotate in one direction. For this reason, a protective device
(phase proctector) is fitted to prevent incorrect wiring of the electrical phases. When the three phases
are not connected correctly, the phase protector operates, and the unit will not start. This devise is located
in the control box of model MAC/ M4AC080~150C/CR.
The following tables shows the LED indicator light for phase proctector under normal operation and fault
coonditions.
LED
Description
Normal operation
Reverse phase
T phase missing
S phase missing
R phase missing
S & T phase missing
Overload
+
Sensor missing
○
On
+
+
●
PW
(Red)
P_R
(Yellow)
P_S
(Yellow)
P_T
(Yellow)
○
◑
◑
◑
●
◑
◑
◑
●
◑
●
●
●
●
●
○
●
◑
●
◑
●
◑
●
○
●
◑
◑
●
●
◑
●
○
Off
◑
Actions
Swith off the unit. Check the 3 phase wiring.
Swith off the unit. Check the 3 phase wiring.
Swith off the unit. Check the 3 phase wiring.
Swith off the unit. Check the 3 phase wiring.
Swith off the unit. Check the 3 phase wiring.
High discharge temperature. Check the refrigerant system.
Swtich off the unit. Plug in sensor.
Fast Blink
Notes: 1. “+” indicates additional for PP01 phase proctector.
2. When R phase missing. no LED or buzzer will indicate the error, but relay 71 and 81 will cut off.
163
Exploded View and Part List
Model : MAC/ M4AC020 / 025/ 030C
9
11
8
3
1
15
10
5
16
18
20
13
4
12
2
17
164
7
19
14
6
ITEM
1
2
3
4
5
6
7
DESCRIPTION
TOP PANEL
STRUCTURE FRONT RIGHT
PANEL SUPPORT PILLAR
ASSY, PANEL ORIFICE
STRUCTURE REAL RIGHT
PANEL RIGHT
ASSY BASE PAN
ASSY BASE PAN
8 PANEL PARTITION
9 ASSY, COIL M(4)AC020C
ASSY, COIL M(4)AC020CR
ASSY, COIL M(4)AC025 C
ASSY, COIL M(4)AC025CR
ASSY, COIL M(4)AC030C
ASSY, COIL M(4)AC030CR
10 COIL GUIDE BACK
11 COIL GUIDE LEFT
12 ASSY. CONTROL BOX
13 COVER, TERMINAL BOX
14 WATER STORAGE TANK 22L
15 HEAT EXCHANGER, BPHE
HEAT EXCHANGER, BPHE
16 CLAMP, BPHE
CLAMP, BPHE
17 COMPRESSOR MAC020C/CR
COMPRESSOR M4AC020C/CR
COMPRESSOR MAC025C/CR
COMPRESSOR M4AC025C/CR
COMPRESSOR MAC030C/CR
COMPRESSOR M4AC030C/CR
18 ASSY, UNIT TUBING
19 ASSY, WATER PIPING
20 ASSY. FAN MOTOR
PARTS NOT SHOWED IN DIAGRAM
FILTER DRIER M(4)AC020/25/30C
FILTER DRIER M(4)AC020/025/030CR
CONTROL MODULE, MC01 EC M(4)AC020/25/30C
CONTROL MODULE, MC01 HP M(4)AC020/025/030CR
TANK, EXPANSION 2 LITER
VAVLE, PRSS RELIFT
PUMP, WATER
PART NUMBER
R01014058833
R01014058975
R01014058974
R50014060810
R01014058976
R01014058978
R50014061048
R50014061049
R01014058980
R50024064810
R50024081356
R50024064816
R50024081358
R50024064846
R50024081360
R01024058986
R01024058985
R01014064127
R50064061062
R02209018354
R02209018356
R01014061320
R01014061322
R04019019032
R04019010654
R50049013221
R50049008112
R50049018853
R50049018851
R50039019117
R02169018759
R02169018760
R04084063454
R04084063455
R05019018922
R05024050808
R04139018353
RELATED MODEL
M(4)AC020C/CR M(4)AC025C/CR M(4)AC030C/CR
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
1. ALL SPECIFICATION ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE
165
9
9
9
9
9
9
9
9
9
9
9
9
9
9
Model : MAC/ M4AC040 / 050 / 060C
3
9
1
8 16
15
11
10
5
12
23
13
20
14
21
11
18
6
22
7
4
2
19
17
166
ITEM
1
2
3
4
5
6
7
8
9
DESCRIPTION
PANEL TOP
ASSY STRUTURE FRONT RIGHT TOP
PANEL, SUPPORT PILLAR
PANEL ORIFICE
ASSY STRUTURE REAR RIGHT
PANEL, RIGHT
ASSY, BASE PAN
PANEL PARTITION
ASSY COIL M(4)AC040/050C
ASSY COIL M(4)AC040/050CR
ASSY, COIL M(4)AC060C
ASSY, COIL M(4)AC060CR
10 COIL GUARD
11 COIL GUARD
12 ASSY. CONTROL BOX
13 COVER, TERMINAL BOX
14 ASSY, INS WATER STORAGE TANK 40L
15 CLAMP, BPHE
CLAMP, BPHE
CLAMP, BPHE
16 HEAT EXCHANGER, BPHE
HEAT EXCHANGER, BPHE
HEAT EXCHANGER, BPHE
17 COMPRESSOR MAC040C/CR
COMPRESSOR M4AC040C/CR
COMPRESSOR MAC050C/CR
COMPRESSOR M4AC050C/CR
COMPRESSOR MAC060C/CR
COMPRESSOR M4AC060C/CR
18 ASSY, PUMP BASE
19 PUMP,WATER
PUMP,WATER
20 ASSY, UNIT TUBING
21 ASSY, WATER PIPING
22 ASSY, FAN MOTOR
23 ASSY, S. HOISTING BRACKET
PARTS NOT SHOWED IN DIAGRAM
CONTROL MODULE MC01 EC M(4)AC040/050/060C
CONTROL MODULE MC01 HP M(4)AC040/050/060CR
VALVE, PRESS RELIFT
TANK, EXPANSION 5 LITER
PART NUMBER
R01014058833
R50014078230
R01014058828
R50014060812
R50014062763
R01014058830
R50014061520
R01014058831
R50024064859
R50024060027
R50024064864
R50024060026
R01024058841
R01024058840
R01014063767
R50064061154
R01014061746
R01014061747
R01014061748
R02209018404
R02209018403
R02209018405
R50049013223
R50049008114
R50049004675
R50049012601
R50049016337
R50049015682
R50014062970
R04139021339
R04139018353
R50039019117
R50014022906
R04084063454
R04084063455
R05024050808
R05019018923
RELATED MODEL
M(4)AC040C/CR M(4)AC050C/CR M(4)AC060C/CR
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
1. ALL SPECIFICATION ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE
167
9
9
9
9
9
9
9
9
Model : M4AC/ MAC080 / 100C/CR
7
17
38
9
10
41
37
36
35
33
32
40
26
25
18
21
16
8
2
6
24
5
19
28
30
15
29
14
3
12
13
11
4
31
1
20
27
22
168
34
ITEM
DESCRIPTION
ASSY, BASE PAN
ASSY, INS PARTITION PANEL
SUPPORT, FLUTTED WIRE
ASSY, RIGHT PANEL
ASSY, LEFT PANEL
PANEL, SUPPORT FRONT
STRUCTURE BACK L/R
PANEL, COIL SUPPORT
PANEL, RIGHT ORIFICE
PANEL, LEFT ORIFICE
SUPPORT, EXPANSION TANK
DOOR HINGE
ASSY, DOOR PANEL RIGHT
ASSY, PANEL DOOR LEFT
ASSY, COIL RIGHT MAC080/100C
ASSY, COIL RIGHT M4AC080/100C
ASSY, COIL RIGHT M(4)AC080/100CR
16 ASSY, COIL LEFT MAC080/100C
ASSY, COIL LEFT M4AC080/100C
ASSY, COIL RIGHT M(4)AC080/100CR
17 ACCUMULATOR
18 LIQUID RECEIVER
19 BRACKET BPHE
20 SUPPORT, TUBE
21 CLIP, FILTER
22 COMPRESSOR MAC080C/CR
COMPRESSOR M4AC080C/CR
COMPRESSOR MAC100C/CR
COMPRESSOR M4AC100C/CR
23 HEAT EXCHANGER M(4)AC080C/CR
HEAT EXCHANGER M(4)AC100C/CR
24 CLAMP, BPHE M(4)AC080C/CR
CLAMP, BPHE M(4)AC100C/CR
25 INS,ACCUMULATOR BODY
26 INS, LIQUID RECEIVER
27 PANEL, TERMINAL BOX SUPPORT
28 ASSY. CONTROL BOX
29 PANEL, FRONT MAC080/100C/CR
PANEL, FRONT M4AC080/100C/CR
30 ASSY, PANEL HOOK
31 PUMP, WATER
32 EXPANSION TANK 8L
33 CLAMP, EXPANSION TANK
34 ASSY, PANEL PARTITION
35 BRACKET, FAN MOTOR
36 FAN MOTOR
37 FAN BLADE
38 FAN GUARD 24"
PARTS NOT SHOWED IN DIAGRAM
HANDSET, SM01XX (MCQUAY)
CONTROL MODULE MC01 EC M(4)AC080/100C
CONTROL MODULE MC01 HP M(4)AC080/100CR
PHASE PROTECTOR
LOW PRESSURE SWITCH M(4)AC080/100C
LOW PRESSURE SWITCH M(4)AC080/100CR
HIGH PRESSURE SWITCH MAC080/100C/CR
HIGH PRESSURE SWITCH M4AC080/100C/CR
FILTER DRIER M(4)AC080/100C
FILTER DRIER M(4)AC080/100CR
VALVE, TXV M(4)AC080/100C
4 WAYS VALVE M(4)AC080/100CR
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
PART NUMBER
R50014055243
R50014085323
R50014085322
R01014082118
R01014054710
R01014054711
R01014082121
R01014082120
R01014054712
R01029016097
R50014074752
R50014056078
R50024059674
R50024056222
R50024054901
R50024059673
R50024056221
R50024054900
R01014054725
R50049013223
R50049008114
R50049004675
R50049012601
R02209015978
R02209015977
R01014056545
R01014056546
R01014082115
R01014082114
R04139021185
R05019001497
R01014054754
R50014055238
R01024055742
R03039015508
R03029015512
R01024055748
R04089019059
R04084063465
R04084063456
R04089018834
R04109015125
R04109015400
R04109015136
R04109018820
R02164028078
R02164034987
R05019016742
R05019002106
RELATED MODEL
M(4)AC080C M(4)AC080CR M(4)AC100C MAC100CR
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
-
9
9
9
9
9
9
9
9
1. ALL SPECIFICATION ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE
169
9
9
9
9
9
9
9
9
-
9
9
9
9
9
9
9
9
Model : M4AC/ MAC120 / 150C/CR
23
6 20 12
38
11
33
30
35
21
31
27
28
5
2
14
26
3
24
4
4
23
5
22
5
13
18
34
4
25
10
16
17
3
7
19
170
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
DESCRIPTION
ASSY, BASE PAN
ASSY, PANEL PARTITION
PANEL, SIDE RIGHT
PANEL, SIDE LEFT
PANEL, COIL SUPPORT
STRUCTURE BACK L/R
PANEL,CONTROL BOX SUPPORT
ASSY, CONTROL BOX MAIN
PANEL, SUPPORT FRONT
SUPPORT,WIRE FLUTTED
PANEL, RIGHT ORIFICE
PANEL, LEFT ORIFICE
PANEL, FRONT M4AC120/150C/CR
PANEL, FRONT MAC120/150C/CR
14 ASSY, COIL LEFT MAC120/150C
ASSY, COIL LEFT M4AC120/150C
ASSY, COIL LEFT M(4)AC120/150CR
15 ASSY, COIL RIGHT MAC120/150C
ASSY, COIL RIGHT M4AC120/150C
ASSY, COIL RIGHT M(4)AC120/150CR
16 DOOR HINGE
17 ASSY, DOOR PANEL RIGHT
18 ASSY, PANEL DOOR LEFT
19 COMPRESSOR MAC120C/CR
COMPRESSOR M4AC120C/CR
COMPRESSOR MAC150C/CR
COMPRESSOR M4AC150C/CR
20 ACCUMULATOR
21 LIQUID RECEIVER
22 BRACKET BPHE
23 HEAT EXCHANGER
HEAT EXCHANGER
24 CLAMP, BPHE
CLAMP, BPHE
25 SUPPORT, TUBE
26 CLIP, FILTER
27 COIL GUARD, BACK
28 COIL GUARD, L/R
29 FAN GUARD 26"
30 INS, ACCUMULATOR BODY
31 INS, LIQUID RECEIVER BODY
32 SUPPORT, EXPANSION TANK
33 CLAMP EXPANSION TANK
34 PUMP, WATER
35 EXPANSION TANK 8L
36 BRACKET, FAN MOTOR
37 FAN MOTOR
FAN MOTOR
38 FAN BLADE
PARTS NOT SHOWED IN DIAGRAM
CONTROL MODULE MC01 EC M(4)AC120/150C
CONTROL MODULE MC01 HP M(4)AC120/150CR
HANDSET, SM01XX (MCQUAY)
PHASE PROTECTOR
LOW PRESSURE SWITCH
LOW PRESSURE SWITCH
HIGH PRESSURE SWITCH MAC120/150C/CR
HIGH PRESSURE SWITCH M4AC120/150C/CR,
FILTER DRIER
FILTER DRIER
4 WAY VALVE
VALVE, TXV
PART NUMBER
R50014055342
R50014055348
R01014082113
R01014082112
R01014054711
R01014054710
R01014082119
R01014082123
R01014082122
R01014082116
R01014082117
R50024059678
R50024056228
R50024054943
R50024059679
R50024056227
R50024054944
R01029016097
R50014074750
R50014055347
R50049016337
R50049015682
R50049004676
R50049014526
R01014054725
R02209015975
R02209015976
R01014054741
R01014054740
R01024055747
R01014054712
R01014054754
R04139021186
R05019001497
R01024055741
R03039018420
R03039018421
R03029015513
R04084063465
R04084063456
R04089019059
R04089018834
R04109015125
R04109015400
R04109015136
R04109018820
R02164028078
R02164034987
R05019028873
R05019015478
RELATED MODEL
M(4)AC120C M(4)AC120CR M(4)AC150C M(4)AC150CR
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
-
1. ALL SPECIFICATION ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE
171
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
-
Model : M5AC 020 / 025CR
3
11
8
9
15
1
16
10
6
18
13
21
4
12
2
17
172
20
7
19
14
6
ITEM
1
2
3
4
5
6
7
8
9
DESCRIPTION
PANEL, TOP
STRUCTURE, FRONT RIGHT
PANEL, SUPPORT PILLAR
ASSY, PANEL ORIFICE
STRUCTURE, REAR RIGHT
PANEL, RIGHT
ASSY, BASE PAN
PANEL, PARTITION
ASSY, COIL
ASSY, COIL
10 COIL GUARD, BACK
11 COIL, GUARD LEFT
12 ASSY, CONTROL BOX
ASSY, CONTROL BOX
13 COVER, TERMINAL BOX
14 ASSY, INS WATER STORAGE TANK 22L
15 HEAT EXCHANGER, BPHE
HEAT EXCHANGER, BPHE
16 CLAMP, BPHE
CLAMP, BPHE
17 COMPRESSOR
COMPRESSOR
18 ASSY. UNIT TUBING
19 ASSY, WATER PIPING
20 SUPPORT, TUBE
21 ASSY,FAN MOTOR
PARTS NOT SHOWED IN DIAGRAM
TANK, EXPANSION 2 LITER
FILTER DRIER
PUMP,WATER
VALVE, PRESS.RELIEF
HANDLING HANDLE
HANDSET, SM01XX (MCQUAY)
DIFF.PRESSURE SWITCH
ASSY, CAP TUBE HEATING
ASSY, CAP TUBE HEATING
ASSY, CAP TUBE COOLING
ASSY, CAP TUBE COOLING
CONTROL MODULE, MC01 HP
CAPACITOR, CMPSR 3uF/440
CAPACITOR, CMPSR 45uF/450VAC
VALVE, ACCESS ½"
VALVE, ACCESS ¼"
STICKER,LOGO MCQUAY
PART NUMBER
R01014058833
R01014058975
R01014058974
R50014060810
R01014058976
R01014058978
R50014061048
R01014058980
R50024078423
R50024078923
R01024058986
R01024058985
R50044066916
R50044080491
R01014064127
R50064061062
R02209024436
R02209022052
R01014061320
R01014061321
R04019020449
R04019022149
R01014063180
R50039019117
R05019018922
R02169018760
R04139018353
R05024050808
R12014015328
R04089019059
R04109014874
R50024079564
R50024062717
R50024079563
R50024062696
R04084063455
R04029026757
R04029026778
R05019023908
R05014066271
R08024067040
RELATED MODEL
M5AC020CR
M5AC025CR
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
1. ALL SPECIFICATION ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE
173
Model: M5AC030CR
14
2
9
4
5
16
21
3
13
8
19
22
25
24
12
17
11
10
23
15
1
18
6
174
20
7
ITEM
DESCRIPTION
1 ASSY, BASE PAN
2 PANEL, SUPPORT PILLAR
3 PANEL, PARTITION
4 ASSY, COIL
5 HEAT EXCHANGER, BPHE
6 COMPRESSOR
7 FILTER DRIER
8 STRUCTURE, REAR RIGHT
9 PANEL, TOP
10 STRUCTURE, FRONT RIGHT 5AC030CR
11 ASSY, PANEL ORIFICE
12 PANEL, RIGHT
13 COIL GUARD, BACK
14 COIL, GUARD LEFT
15 ASSY, CONTROL BOX
16 CLAMP, BPHE
17 ASSY, FAN MOTOR
18 PUMP, WATER
19 TANK, EXPANSION 2 LITER
20 SUPPORT, TUBE
21 CLIP, FILTER 5AC030CR
22 CLAMP. EXPANSION TANK
23 COVER, TERMINAL BOX
24 ASSY, UNIT TUBING
25 ASSY, WATER PIPING
Parts Not in Diagram
CONTROL MODULE MC01 HP
HANDSET, WIRED SM01XX MCQUAY
STICKER,LOGO MCQUAY
R50014069928
R01014058974
R01014058980
R50024069941
R02209022052
R04019021176
R02169018760
R01014069935
R01014064936
R01014069936
R50014060810
R01014069933
R01024058986
R01024058985
R50044076662
R01014061321
R50039019117
R04139018353
R05019018922
R01014071995
R01014071927
R01014072222
R01014069940
R50024069943
R50024069949
RELATED MODEL
M5AC030CR
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
R04084068700
A04089020999
A08024067040
9
9
9
PART NUMBER
1. ALL SPECIFICATION ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE
175
Model : M5AC040 / 050/ 055CR
10
4
8
1
15
9
17
6
11
19
16
12
32
27
30
33
14
20
13
24
29
21
28
7
18
3
5
31
2
25
23
26
176
22
ITEM
1
2
DESCRIPTION
PANEL, TOP
ASSY, BASE PAN
ASSY, BASE PAN
3 ASSY, STRUCTURE FRONT RIGHT TOP
4 ASSY, SUPPORT PILLAR
5 ASSY, PANEL ORIFICE
6 ASSY, STRUCT. REAR RIGHT
7 PANEL, RIGHT
8 PANEL, PARTITION
9 COIL GUARD, BACK
10 COIL GUARD, LEFT
11 ASSY, CONTROL BOX
ASSY, CONTROL BOX
12 COVER, TERMINAL BOX
13 ASSY, PUMP BASE
14 PUMP, WATER
15 ASSY,SOLENOID COIL
16 CLAMP, BPHE
CLAMP, BPHE
CLAMP, BPHE
17 HEAT EXCHANGER,BPHE
HEAT EXCHANGER,BPHE
HEAT EXCHANGER,BPHE
18 ASSY, FAN MOTOR
19 ASSY, S. HOISTING BRACKET
20 PLATE, PUMP SUPPORT
21 SUPPORT, ACCUMULATOR
22 ACCUMULATOR
23 SUPPORT,ACCU & LIQUID RECEIVER
24 LIQUID RECEIVER
25 COMPRESSOR
COMPRESSOR
26 COMPRESSOR
COMPRESSOR
27 TANK, EXPANSION 5 LITER
28 INS, ACCUMULATOR BODY
29 INS, LIQUID RECEIVER BODY
30 CLIP, EXPANSION TANK
31 CLIP, FILTER
32 ASSY, UNIT TUBING
ASSY, UNIT TUBING
ASSY, UNIT TUBING
33 ASSY, WATER PIPING
ASSY, WATER PIPING
ASSY, WATER PIPING
Parts Not in Diagram
CONTROL MODULE MC01 HP
HANDSET, WIRED SM01XX MCQUAY
FILTER DRIER
STICKER,LOGO MCQUAY
R01014064936
R50014061524
R50014065985
R50014078915
R50014062762
R50014060812
R50014064939
R01014079937
R01014065858
R01024058841
R01024058840
R50044076664
R50044076665
R01014065057
R50014065859
R04139020248
R50134065210
R01014061746
R01014061747
R01014061748
R02209020577
R02209020578
R02209021556
R50039019117
R50014022906
R01014061851
R01014067320
R02119016393
R01014059624
R02119020906
R50049021175
R50049021179
R50049021177
R50049021173
R05019018923
R01014068177
R01014071226
R50024067840
R50024068183
R50024069541
R50024067637
R50024067648
R50024069491
M5AC040CR
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
-
RELATED MODEL
M5AC050CR
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
-
M5AC055CR
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
R04084068700
R04089020999
R02164034987
R08024067040
9
9
9
9
9
9
9
9
9
9
9
9
PART NUMBER
1. ALL SPECIFICATION ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE
177
Products manufactured in an ISO certified facility.
This document contains the most current product information as of this printing. For the
most up-to-date product information, please go to www .mcquay. com.
© 2009 McQuay International
+1 (800) 432-1342
www .mcquay. com
Download PDF