Operation Guide 5146

MO1003-EA
Operation Guide 5146
About This Manual
• Depending on the model of your watch, display text
appears either as dark figures on a light background or
light figures on a dark background. All sample displays
in this manual are shown using dark figures on a light
background.
• Button operations are indicated using the letters shown
in the illustration.
• Note that the product illustrations in this manual are
intended for reference only, and so the actual product
may appear somewhat different than depicted by an
illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
Stopwatch Mode
General Guide
Countdown Timer Mode
▲
▲
• Press C to change from mode to mode.
• In any mode (except a setting mode), press B to illuminate the display.
Timekeeping Mode
World Time Mode
▲
▲
Alarm Mode
▲
Press C.
Timekeeping
lll
Day of week
ll
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A for about three
llll
seconds until the currently selected city code flashes in
the upper digital display. This is the setting mode.
2.
Press
C. This will display the DST setting screen.
l
l
l
3. Use D to toggle the DST setting on (on) and off (OFF).
• The default DST setting is off (OFF).
4. When the setting you want is selected, press A to exit
the setting mode.
DST indicator
• The DST indicator appears to indicate that Daylight
Saving Time is turned on.
lll
Home City Time
Day of week
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
l l ll l
Home City Date
Daylight Saving Time (DST)
lll
You can adjust the Home Time city date and time in the Timekeeping Mode.
• The analog time of this watch is synchronized with the digital time. The analog time
setting is adjusted automatically whenever you change the digital time.
• If the analog time does not match the digital time for any reason, use the procedure
described under “To adjust home positions” to match the analog setting to the digital
setting.
• Pressing D in the Timekeeping Mode toggles digital display between the Home City
Date and Home City Time.
ll
▲
▲
D
Month Day Seconds
PM indicator Hour : Minutes Seconds
ll
lll
To set the digital time and date
1. In the Timekeeping Mode, hold down A for about three
City code
seconds until the currently selected city code flashes in
the upper digital display. This is the setting mode.
l
l
l
l
2. Use D (east) and B (west) to select the city code you
want.
• Make sure you select your Home City code before
changing any other setting.
• For full information on city codes, see the “City Code
Table”.
l l ll l
PM indicator
Seconds
12-hour and 24-hour timekeeping
• With the 12-hour format, the PM indicator (P) appears for times in the range of noon to
11:59 p.m. and no indicator appears for times in the range of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
the PM indicator (P).
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
Stopwatch
Upper display
segments
Hour : Minutes
3. Press C to change the flashing screen content in the sequence shown below to
select the other setting.
City Code
Illumination
Duration
DST
12/24-Hour
Format
Day
Month
Seconds
Year
Hour
Minutes
4. When the setting you want to change is flashing, use D or B to change it as
described below.
Screen:
To do this:
Change the city code
Toggle the DST setting between
Daylight Saving Time (on) and
Standard Time (OFF).
Toggle between 12-hour (12H) and
24-hour (24H) timekeeping
Reset the seconds to 00
Change the hour and minutes
Do this:
Use D (east) and B
(west).
Press D.
Important!
• Check to make sure that the speed hand is not moving before you perform any
Stopwatch Mode button operation.
Specifying a Distance Value
Press D.
Press D.
Use D (+) and B (–).
Change the year, month, or day
Toggle the display illumination
duration between 1.5 seconds (LT1)
and three seconds (LT3)
Speed hand
You can use the stopwatch to measure elapsed time, lap
times and split times. If you specify a distance value, the
stopwatch also will calculate and display speeds.
• The digital display range of the stopwatch is 99 hours,
59 minutes, 59.999 seconds. The stopwatch continues
to run until you stop it. If it reaches the above limit, it will
restart the time measurement from zero.
• The stopwatch operation continues even if you exit the
Stopwatch Mode. If you exit the Stopwatch Mode while a
stopwatch operation is in progress, the segments along
the top of the upper digital display (upper display
segments) will indicate the seconds of the current time.
Each segment represents one second. This is to let you
know that a stopwatch operation is in progress.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
Press D.
You can use the procedure below to specify a distance value, if you want. If you
specify a distance value, the watch will calculate and indicate speed for certain
stopwatch operations.
• The distance value represents kilometers, miles, or any other distance unit you want.
Specifying a distance value of 10.0, for example, can mean 10.0 kilometers or 10.0
miles.
• No speed calculation is performed when 0.0 is specified as the current distance
value.
• For lap time readings, you can specify either the lap distance (when all the laps are
the same distance) or the total race distance.
• For split time readings, you can specify the total race distance only. Though the
watch will indicate a speed each time you take a split reading, they will be based on
the total race distance, and so they will not indicate actual intermediate split speeds.
5. Press A to exit the setting mode.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
1
Operation Guide 5146
lll
lll
How speed is indicated
Segments
(100 unit)
OVER
Split Time
A split time reading shows the time elapsed since the
beginning of the current time measurement.
• If you want the watch to calculate the speed of the race,
specify the race distance for the distance setting.
• For split time readings, you can specify the total race
distance only. Though the watch will indicate a speed
each time you take a split reading, they will be based on
the total race distance, and so they will not indicate
actual intermediate split speeds.
lll
To specify a distance value
1. In the Stopwatch Mode, make sure the stopwatch is
stopped and reset to all zeros.
• If you need to reset the stopwatch to all zeros, press A.
2. Hold down A for about three seconds until the current
distance
value setting flashes in the lower digital display.
l
l
l
l
• This is the distance value setting mode.
3. Press C to move the flashing between the values on
the left side and right side of the distance value decimal
point.
4. While a distance value is flashing, use D (+) and B (–)
to change it.
• You can specify a distance value in the range of 0.1 to
99.9.
5. After specifying the distance value you want, press A
to exit the setting mode.
Speed hand
(Up to 100)
1000 indicator
• While an elapsed time measurement operation is being
performed in the Stopwatch Mode, the watch will
indicate a speed value, which is calculated based on the
distance you specified and the elapsed time.
The speed value is indicated as described below.
Speed hand: Up to 100
Upper display segments: 100 unit
A 1000 indicator points to 1000 (located to the right of
the upper display segments) when the speed value
exceeds 1000.
• The speed hand indicates speed values less than 100.
Only even-numbered values are indicated.
• Speed can be indicated from 0 to 1998. OVER is
indicated by the speed hand when the speed exceeds
1998.
Example:
When the speed value is 1,740.
Speed hand: Indicates 40.
Upper display segments: Indicate 700.
1000 indicator: Displayed
Time Measurement
You need to specify either lap time or split time measurement before you start a
stopwatch operation.
• If you want to measure total elapsed time, select split time measurement.
To specify lap time or split time readings
1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.
• Make sure that LAP (lap times) or SPL (split times) is shown in the lower digital
display.
• If you need to reset the stopwatch to all zeros, press A.
2. You can toggle between LAP (lap times) and SPL (split times) by pressing A.
Split time
To set up the stopwatch to take split time readings
1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.
• If you need to reset the stopwatch to all zeros, press A.
2. Make sure that SPL (split times) is shown in the lower digital display.
• If LAP (lap times) is displayed, press A to toggle it to SPL.
To perform a split time measurement
Select split time (SPL) measurement and then perform
Speed hand (calculated)
the following button operations.
Hours
D Start ➝ A Split ➝ A Split Release* ➝
D Stop ➝ A Reset
* The split time is released automatically if you do not
press A within about 12 seconds.
• You can press A to take split readings as many times
as you like.
• The stopwatch continues elapsed time measurement
internally while a split time reading is displayed.
• Pressing A while a split time is displayed will switch
Minutes
back to normal elapsed time measurement. The elapsed
Seconds
1/1000
time will appear in the lower digital display.
seconds
• You also could press D to stop elapsed time
measurement instead.
• Pressing D to stop elapsed time measurement displays
the time (and speed if a distance is specified) of the final
split (which is the overall elapsed time).
To measure times with the stopwatch
Elapsed Time
D
Start
➤ D
Stop
Lap Time
D
Start
( LAP
➤ A
Lap
(Lap01)
displayed)
Split Time
D
➤ A
Split
Start
➤ A
Reset
➤ A
Lap
(Lap02)
➤ D
Stop
➤ A
Reset
➤ A
Split release
➤ D
Stop
➤ A
Reset
( SPL displayed)
▲
▲
A
Countdown Timer
Auto-repeat off
Elapsed Time Measurement
Use the following procedure to measure elapsed time, without taking lap time or split
time readings.
Lap time
A lap time reading shows the time elapsed since the last
lap time reading was taken.
• If you want the watch to calculate the speed of each lap
(when all of the laps are the same distance), specify the
lap distance for the distance setting.
• If you want the watch to calculate the speed of the entire
race, specify the race distance for the distance setting.
A speed will be indicated each time you take a lap
reading, but these lap speeds will not indicate actual
speed of the entire race.
To set up the stopwatch to take lap time readings
1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.
• If you need to reset the stopwatch to all zeros, press A.
2. Make sure that LAP (lap times) is shown in the lower digital display.
• If SPL (split times) is displayed, press A to toggle it to LAP.
To configure countdown start time and auto-repeat settings
1. While the countdown start time is on the display in the
Auto-repeat on
Countdown Timer Mode, hold down A for about three
seconds until the hour setting of the countdown start
time starts to flash. This is the setting mode.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
l
l
l
display it.
l
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
lll
To perform a lap time measurement
Select lap time (LAP) measurement and then perform the
Lap number
following button operations.
Hours
Speed hand
D Start ➝ A Lap* ➝ A Lap* ➝
(calculated)
D Stop ➝ A Reset
* Normal elapsed time measurement reappears after
about 12 seconds.
• You can press A to take lap readings as many times as
you like.
• While a lap time is displayed, the upper digital display
will alternate between the lap number (#01 to #99) and
the lap hour value. If you take more than 99 lap
Minutes
readings, the lap number will restart from #00 following
lap #99.
1/1000
Seconds seconds • Pressing D to stop elapsed time measurement displays
the time (and speed if a distance is specified) of the final
lap.
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm will sound for 10 seconds or
until you stop it by pressing any button.
• The countdown time is reset to its starting value automatically after the alarm stops
if auto-repeat is turned off.
• When auto-repeat is turned on, the countdown will restart automatically without
pausing when it reaches zero.
• The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
• Press D while a countdown operation is in progress to pause it.
Press D again to resume the countdown.
• To stop a countdown timer operation completely, first pause it (by pressing D), and
then press A. This returns the countdown time to its starting value.
lll
Lap Time
Start time
(Hours : Minutes) Seconds
lll
To perform elapsed time measurement
Select split time (SPL) measurement and then perform the following button operations.
D Start ➝ D Stop ➝ A Reset
• If you have a distance value specified for the current elapsed time measurement, the
upper display segments and speed hand will indicate the speed when you press D
to stop the elapsed time operation.
• After pressing D to stop an elapsed time operation, you could press D again to
restart from the point where you left off.
You can set the countdown start time within a range of
one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• You also can select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
Start time
(Hours : Minutes)
Start Time
(Hours)
Start Time
(Minutes)
Auto-Repeat
On/Off
3. Perform the following operations, depending on which setting currently is selected
on the display.
• While the start time setting is flashing, use D (+) and B (–) to change it.
• While the auto-repeat on/off setting is flashing on the display, press D to toggle
) and off (
).
auto-repeat on (
4. Press A to exit the setting mode.
) is displayed on the Countdown Timer Mode screen while
• The auto-repeat on (
this function is turned on.
2
Operation Guide 5146
World Time
• All of the operations in this section are performed in the World Time Mode, which
you enter by pressing C.
To view the current time in another time zone
In the World Time Mode, use D to scroll through available city codes (time zones).
• The lower digital display will show the time in the currently selected World Time City.
• A PM indicator (P) will be displayed in the lower digital display between the hours of
noon and midnight.
• When the city code (time zone) you want is selected, you can press A to display
the date. After about one second, the watch will resume regular timekeeping for the
currently selected city.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off.
• Alarm and Hourly Time Signal operations are performed in accordance with the
current time in your Home City, as kept in the Timekeeping Mode.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the SNZ setting screen
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
Snooze
Alarm on
2. Press A to toggle it on (on) and off (OFF).
alarm
indicator
• Turning on a alarm (AL1, AL2, AL3, AL4 or SNZ)
indicator
displays the alarm on indicator on its Alarm Mode
screen.
• In all modes, the alarm on indicator is shown for any
alarm that currently is turned on.
• The alarm on indicator flashes while the alarm is
sounding.
• The snooze alarm indicator flashes while the snooze
alarm is sounding and during the 5-minute intervals
On/Off
between alarms.
status
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Hourly time signal
Signal (SIG).
on indicator
2. Press A to toggle it on (on) and off (OFF).
• The Hourly Time Signal on indicator is shown on the
display in all modes while this function is turned on.
Press A.
▲
One second
Seconds
PM indicator
Hour : Minutes
Date
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, press D to display the city
code (time zone) whose Standard Time/Daylight Saving
Time setting you want to change.
2. Hold down A for about three seconds to toggle
between Daylight Saving Time ( DST indicator
displayed) and Standard Time ( DST indicator not
displayed).
• A DST indicator will be displayed in the lower digital
DST indicator
display if Daylight Saving Time is turned on.
• You can turn on DST individually for each city code,
except UTC.
• Turning on DST for the city code that is currently
selected as your Home City will turn on DST for normal
timekeeping.
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This
changes your Home City to your World Time City, and your World Time City to your
Home City. This capability can come in handy when you frequently travel between two
cities in different time zones.
Alarms
Illumination
An LED (light-emitting diode) illuminates the face of the
watch for easy reading in the dark. The watch’s auto light
switch turns on illumination automatically when you angle
the watch towards your face.
• The auto light switch must be turned on (indicated by
the auto light switch on indicator) for it to operate.
• See “Illumination Precautions” for other important
information about using illumination.
Auto light switch on
indicator
To illuminate the display manually
In any mode, press B to turn on illumination.
• The above operation turns on illumination regardless of
the current auto light switch setting.
• You can use the procedure below to select either 1.5
seconds or 3 seconds as the illumination duration. When
you press B, illumination will remain on for about 1.5
seconds or 3 seconds, depending on the current
illumination duration setting.
To specify the illumination duration
1. In the Timekeeping Mode, hold down A until the
lll
display contents start to flash. This is the setting mode.
2. Press C nine times to display the current illumination
duration LT1 or LT3.
3. Press D to toggle the setting between LT1(1.5
seconds) and LT3 (three seconds).
4. Press A to exit the setting mode.
ll
To swap your Home City and World Time City
1. In the World Time Mode, use D to select the World Time City you want.
2. Hold down A and B until the watch beeps.
• This will make the World Time City you selected in step 1 your Home City, and cause
the hour and minute hands to move to the current time in that city. At the same time,
it will change the Home City you had selected prior to step 2 your World Time City,
and cause the content of lower digital display to change accordingly.
• After swapping the Home City and World Time City, the watch stays in the World
Time Mode with the city that was selected as the Home City prior to step 2 now
displayed as the World Time City.
On/Off
status
ll
World Time
World Time digitally displays the current time in one of
48 cities (29 time zones) around the world. A simple
operation swaps your Home City with the currently
selected World Time City.
• The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
• Times in the World Time Mode are based on UTC
offsets. See the “City Code Table” for information about
the UTC offsets that are supported.
lll
Currently selected
World Time City
About the Auto Light Switch
Alarm number
Alarm time
(Hour : Minutes)
When an alarm is turned on, the alarm tone will sound
when its alarm time is reached. One of the alarms is a
snooze alarm, while the other four are daily alarms.
You also can turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• There are five alarm screens numbered AL1, AL2, AL3
and AL4 for the daily alarm, and a snooze alarm screen
indicated by SNZ. The Hourly Time Signal screen is
indicated by SIG.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
Turning on the auto light switch causes illumination to turn on, whenever you position
your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and then tilting it towards
you more than 40 degrees causes illumination to turn on.
• Wear the watch on the outside of your wrist.
Parallel to
ground
More than
40°
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
AL1
On/Off
status
AL2
AL3
AL4
SNZ
SIG
• To set a daily alarm, display alarm screen AL1 , AL2,
AL3 or AL4. To set the snooze alarm, display the SNZ
screen.
• SIG is the Hourly Time Signal setting.
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A for about three seconds until the hour
setting of the alarm time starts to flash. This is the setting mode.
• This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
5. Press A to exit the setting mode.
Warning!
• Always make sure you are in a safe place whenever you are reading the
display of the watch using the auto light switch. Be especially careful when
running or engaged in any other activity that can result in accident or injury.
Also take care that sudden illumination by the auto light switch does not
startle or distract others around you.
• When you are wearing the watch, make sure that its auto light switch is turned
off before riding a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create a
distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down B for about three seconds to toggle the auto
light switch on (auto light switch on indicator displayed) and off (auto light switch on
indicator not displayed).
• The auto light switch on indicator remains in all modes while the auto light switch is
turned on.
• In order to protect against running down the battery, the auto light switch will turn off
automatically approximately six hours after you turn it on. Repeat the above
procedure to turn the auto light switch back on if you want.
3
Operation Guide 5146
Hand Home Position Correction
Specifications
The speed, hour, and minute hands of the watch can be thrown off by exposure to
strong magnetism or impact. The watch is designed to correct speed, hour and minute
hand manually.
Accuracy at normal temperature: ± 15 seconds a month
Digital Timekeeping: Hour, minutes, seconds, p.m. (P), month, day, day of the week
Time format: 12-hour and 24-hour
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Home City code (can be assigned one of 48 city codes); Standard Time /
Daylight Saving Time (summer time)
Analog Timekeeping: Hour, minutes (hand moves every 20 seconds)
Stopwatch:
Measuring unit: 1/1000 seconds
Measuring capacity: 99:59'59.999"
Measuring modes: Elapsed time, Lap time, Split time
Other: Speed
Countdown Timer:
Measuring unit: 1 second
Input range: 1 minute to 24 hours (1-minute increments)
Other: Auto-repeat timing
World Time: 48 cities (29 time zones)
Other: Daylight Saving Time/Standard Time, Home City/World Time City Swapping
Alarms: Four daily alarms, one snooze alarm, Hourly Time Signal
Illumination: LED (light-emitting diode), Auto Light Switch; Selectable illumination
duration
To adjust home positions
Speed hand
ll
lll
ll ll
llll
Correct speed hand
position
Hour and minute hands
ll
ll
lllll
1. In the Timekeeping Mode, hold down D for about three
seconds until Sub flashes in the lower digital display.
• This is the home position adjustment mode.
2. Check the position of the speed hand.
• The speed hand is in the correct home position if it is
pointed at 50 (9 o’clock). If it isn’t, use D to move the
hand clockwise until it is.
• After confirming that the speed hand is in its correct
home position, press C.
3. Check the positions of the hour and minute hands.
• The hands are in the correct home positions if they
are pointed at 12 o’clock. If they aren’t, use D
(clockwise) and B (counterclockwise) to adjust their
positions.
4. When everything is the way you want, press A to
return to regular timekeeping.
• This will cause the hour and minute hands to move to
the current Timekeeping Mode time and the speed hand
to move to the 0 position.
• Pressing C here will return to the setting at the
beginning of step 2.
Battery : One lithium battery (Type: CR1220)
Approximate Battery Life: 2 years on type CR1220
(10 seconds of alarm operation per day, one illumination operation (1.5 seconds)
per day)
ll lll
City Code Table
Correct hour and
minute hand positions
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Auto Return Features
• If you leave the watch with a flashing setting on the display for two or three minutes
without performing any operation, the watch will exit the setting mode automatically.
• The watch will return to the Timekeeping Mode automatically if you do not perform
any operation for two or three minutes in the Alarm Mode.
High-Speed Movement
• The D and B buttons are used to change setting in various setting modes. In most
cases, holding down these buttons will start high-speed movement.
Initial Screens
When you enter the Stopwatch Mode, World Time Mode or Alarm Mode, the data you
were viewing when you last exited the mode will appear first.
Timekeeping
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• The year can be set in the range of 2000 to 2099.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except when battery has replaced.
• The current time for all city codes in the Timekeeping Mode and World Time Mode is
calculated in accordance with the Coordinated Universal Time (UTC) for each city,
based on your Home City time setting.
City
UTC Offset/
City
Code
GMT Differential
PPG
Pago Pago
–11
HNL
Honolulu
–10
ANC
Anchorage
–9
YVR
Vancouver
–8
LAX
Los Angeles
YEA
Edmonton
–7
DEN
Denver
MEX
Mexico City
–6
CHI
Chicago
MIA
Miami
YTO
Toronto
–5
NYC
New York
SCL
Santiago
–4
YHZ
Halifax
YYT
St. Johns
–3.5
RIO Rio De Janeiro
–3
RAI
Praia
–1
UTC
0
LIS
Lisbon
LON
London
MAD
Madrid
PAR
Paris
ROM
Rome
+1
BER
Berlin
STO
Stockholm
City
Code
ATH
CAI
JRS
MOW
JED
THR
DXB
KBL
KHI
DEL
DAC
RGN
BKK
SIN
HKG
BJS
TPE
SEL
TYO
ADL
GUM
SYD
NOU
WLG
City
Athens
Cairo
Jerusalem
Moscow
Jeddah
Tehran
Dubai
Kabul
Karachi
Delhi
Dhaka
Yangon
Bangkok
Singapore
Hong Kong
Beijing
Taipei
Seoul
Tokyo
Adelaide
Guam
Sydney
Noumea
Wellington
UTC Offset/
GMT Differential
+2
+3
+3.5
+4
+4.5
+5
+5.5
+6
+6.5
+7
+8
+9
+9.5
+10
+11
+12
• Based on data as of June 2009.
• The rules governing global times (UTC offset and GMT differential) and summer
time are determined by each individual country.
Illumination Precautions
• Illumination may be difficult to see when viewed under direct sunlight.
• Illumination turns off automatically whenever an alarm sounds.
• Frequent use of illumination runs down the battery.
Auto light switch precautions
• Avoid wearing the watch on the inside of your wrist. Doing so causes the auto light
switch to operate when it is not needed, which shortens battery life. If you want to
wear the watch on the inside of your wrist, turn off the auto light switch feature.
More than 15 degrees
too high
• Illumination may not turn on if the face of the watch is
more than 15 degrees above or below parallel. Make
sure that the back of your hand is parallel to the ground.
• Illumination turns off in about 1.5 seconds or 3 seconds,
even if you keep the watch pointed towards your face.
• Static electricity or magnetic force can interfere with proper operation of the auto
light switch. If illumination does not turn on, try moving the watch back to the starting
position (parallel with the ground) and then tilt it back toward you again. If this does
not work, drop your arm all the way down so it hangs at your side, and then bring it
back up again.
• Under certain conditions, illumination may not turn on until about one second after
you turn the face of the watch towards you. This does not necessarily indicate
malfunction of the auto light switch.
• You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
4