Clay Paky C61401 Instruction manual

ENGLISH
A.LEDA WASH K5
A.LEDA WASH K10
A.LEDA WASH K20
®
C61401
C61405
C61410
INSTRUCTION MANUAL
INDEX
Page
Contents
2
Safety information
3
Unpacking and preparation
4
Installation and start-up
5
Control panel
7
Menu setting
14
Maintenance
16
Optional accessories
19
Technical information
19
Cause and solution of problems
20
Channel functions
Congratulations on choosing a Clay Paky product!
We thank you for your custom.
Please note that this product, as all the others in the rich Clay
Paky range, has been designed and made with total quality to
ensure excellent performance and best meet your expectations
and requirements.
Carefully read this instruction manual in its entirety and keep it
safe for future reference. It is essential to know the information
and comply with the instructions given in this manual to ensure
the fitting is installed, used and serviced correctly and safely.
CLAY PAKY S.p.A. disclaims all liability for damage to the fitting
or to other property or persons deriving from installation, use and
maintenance that have not been carried out in conformity with this
instruction manual, which must always accompany the fitting.
CLAY PAKY S.p.A. reserves the right to modify the
characteristics stated in this instruction manual at any time and
without prior notice.
1
SAFETY INFORMATION
• Installation
Make sure all parts for fixing the projector are in a good state of repair.
Make sure the point of anchorage is stable before positioning the projector.
The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if
the primary support system fails, the fitting falls as little as possible.
If the safety chain gets used, it needs to be replaced with a genuine spare.
LED
• Minimum distance of illuminated objects
The projector needs to be positioned so that the objects hit by the beam of light are at least 0.20
metres (8”) from the lens of the projector.
0.2
• Minimum distance from flammable materials
The projector must be positioned so that any flammable materials are at least 0.20 metres (8”) from
every point on the surface of the fitting.
• Mounting surfaces
It is permissible to mount the fitting on normally flammable surfaces.
• Maximum ambient temperature
Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).
IP20
• IP20 protection rating
The fitting is protected against penetration by solid bodies of over 12mm (0.47”) in diameter (first
digit 2), but not against dripping water, rain, splashes or jets of water (second digit 0).
• Protection against electrical shock
Connection must be made to a power supply system fitted with efficient earthing (Class I appliance
according to standard EN 60598-1).
It is, moreover, recommended to protect the supply lines of the projectors from indirect contact
and/or shorting to earth by using appropriately sized residual current devices.
• Connection to mains supply
Connection to the electricity mains must be carried out by a qualified electrical installer.
Check that the mains frequency and voltage correspond to those for which the projector is designed
as given on the electrical data label.
This label also gives the input power to which you need to refer to evaluate the maximum number
of fittings to connect to the electricity line, in order to avoid overloading.
tc 90°C
• Temperature of the external surface
The maximum temperature that can be reached on the external surface of the fitting, in a thermally
steady state, is 90°C (194°F).
• Maintenance
Before starting any maintenance work or cleaning the projector, cut off power from the mains
supply.
LiFePO4
• Battery
This product contains a rechargeable lead-acid battery. To preserve the environment, please
dispose the battery at the end of its life according to the regulation in force. Instructions on how to
remove the battery from the product are available on www.claypaky.it
The products to which this manual refers comply with the European Directives pursuant to:
• 2006/95/EC - Safety of electrical equipment supplied at low voltage (LVD)
• 2004/108/EC - Electromagnetic Compatibility (EMC)
• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS)
A.LEDA WASH
2
UNPACKING AND PREPARATION
1
IST004/001
2 x 183102/805
Packing contents - Fig. 1
2
UNLOCKED
3
°
90
A.LEDA WASH
°
90
PAN Mechanism Lock and Release (every 90°) - Fig. 2
°
90
°
90
LOCKED
INSTALLATION AND START-UP
3
Installing the projector - Fig. 3
The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall.
WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request).
This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.
4
1
2
2
3
1
Connecting and disconnecting power cable - Fig. 4
A.LEDA WASH
4
CONTROL PANEL
5
Mains
NB: connecting one “A.leda
Wash K5” to the mains, it is
possible to connect up to a
maximum of 11 “A.leda Wash
K5” in parallel at the same time.
Connecting to the mains supply - Fig. 5
6
DMX 512
5 PIN
5
4
3
1
2
SCREEN
SIGNAL
SIGNAL
DMX 512
DMX 512
3 PIN
SIGNAL
2
SCREEN
1
3
SIGNAL
Connecting to the control signal line (DMX) - Fig. 6
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use
microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 3 or 5-pin male/female
connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the
shield braid and to pin 1 of the connectors.
7
Fixture ID
Dmx Address
2
1
Warning Message
7.5m
Switching on the projector - Fig. 7
Press the switch. The projector starts resetting the effects. At the same time, the following information scrolls on the display:
Model
A.leda Wash
Firmware
Version X.X.X
Date - Hour
xxx (Fixture ID)
Dmx Address xxx
System errors
E: .........................
W: .........................
On conclusion of resetting in case of absence of the dmx signal, Pan and Tilt move to the “Home” position (Pan 50% - Tilt 50%). The control panel
(Fig. 7) has a display and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions:
rest status and setting status. When it is in the rest status, the display shows the projector’s DMX address and the Fixture ID address (if set).
During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status.
It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the
key will be cancelled.
F
Continue
A.LEDA WASH
5
➔
8
28
28
Reversal of the display - Fig. 8
To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and
maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.
Setting the projector starting address
On each projector, the starting address must be set for the control signal (addresses from 1 to 512).
The address can also be set with the projector switched off.
Setting the address: see pag. 8.
Setting the projector Fixture ID
On each projector, the Fixture ID address must be set for an easy identification of the fixtures in an installation (ID from 1 to 255).
The Fixture ID address can be set with the projector switched off.
Setting the Fixture ID: see pag. 8.
B
C
Functions of the buttons - Using the menu
F
C
Confirms the displayed value, or activates the displayed function, or enters the successive
menu.
Decreases the value displayed (with auto-repetitions) or passes to the next item in the menu.
DOWN
B
Increases the value displayed (with auto-repetitions) or passes to the previous item in a menu.
D
Return to the top level.
E
Commute from units, tens, hundreds, in the "Address", "Fixture ID" and "Calibration" menù.
UP
LEFT
RIGHT
USING THE MENU:
1) Press
once – “Main Menu” appears on the display.
2) Use the UP
and DOWN
keys to select the menu to be used:
• Setup (Setup Menu): To set the setting options.
• Option (Option Menu): To set the operating options
• Informations (Informations Menu): To read the counters, software version and other information.
• Manual Control (Manual control Menu): To trigger the test and manual control functions.
• Test (Test Menu): To check the proper functionning of effects
• Advanced (Advanced Menu): Access to the "Advanced menu" is recommended for a trained technical personnel.
To enable the "Advanced" see pag.13
3) Press
to display the first item in the selected menu.
4) Use the UP
and DOWN
keys to select the MENU items.
F
F
B
C
B
C
Setting addresses and options with the projector disconnected
The projector’s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply.
All that is needed is to press
to momentarily activate the display and thus access the settings. Once the required operations have been carried out,
the display will switch off again after a wait time of 30 seconds.
F
A.LEDA WASH
6
MENU SETTING
1
3
2
Set Up
Dmx
Address
Option
Pan / Tilt
Invert
Pan
Information
Invert
Tilt
Channel
Mode
System
Errors
Fixture
Hours
Swap
Pan-Tilt
LED
Energy Tot
Fixture ID
Encoder
Pan-Tilt
Ethernet
Interface
Silent
Mode
System
Version
Standard
Board
Diagnost.
Quiet
Option
Display
Dmx
Monitor
Information
Special
Functions
Manual
Control
Pan/Tilt
speed
Fans
Monitor
Dimmer
curve
Test
Network
params
RGB
Gamma
Halogen
Mode
Advanced
Setting
Default
Preset
User
Preset 1
User
Preset 2
User
Preset 3
4
5
Manual
Control
Reset
Channel
6
Test
Pan / Tilt
Colour
Advanced
Access code
1234
Upload
Aleda fw
All
Setup
Model
Calibration
Continue
A.LEDA WASH
7
➔
NOTE: On grey the default options
Set Up
Dmx
Address
SET UP MENU
DMX ADDRESS
NOTE: without the DMX signal the Address (XXX) flashing
Allows you to select the DMX ADDRESS.
1) Press
- the current DMX Adress appear on the display.
2) Use the UP
and DOWN
, RIGHT
keys to plan the DMX
Address.
3) Press
to confirm the selection or LEFT
to keep current settings.
Address xxx
F
B
C
E
D
F
Channel
Mode
CHANNEL MODE
Allows you to select a channel arrangement from the two available.
1) Press
- the current settings appear on the display (Standard or
Vector).
2) Use the UP
and DOWN
keys to select one of the following
settings:
- Standard
- Shape
- Extended
- Extended RGBW
3) Press
to confirm the selection or LEFT
to keep current settings.
Standard
F
Shape
B
Extended
Extended
RGBW
Fixture ID
C
F
D
FIXTURE ID
Allows you to select the FIXTURE ID.
- the current Fixture ID appear on the display.
1) Press
2) Use the UP
, DOWN
, RIGHT
keys to plan the Fixture ID.
3) Press
to confirm the selection or LEFT
to keep current settings.
Value xxx
F
B
F
C
D
ETHERNET INTERFACE
It lets you set the Ethernet settings to be attributed to the projector.
1) Premere
.
2) Use the UP
and DOWN
keys to select the “Ethernet Interface”
options to set:
Ethernet
Interface
F
B
C
Control Protocol
It lets you select the “Control Protocol” Art-net to assign according to the
control unit used:
1) Press
the current setting appears on the display.
2) Use the UP
and DOWN
keys to select one of the following settings:
- Disabled
- Art-net on IP 2
- Art-net on IP 10
3) Press
to confirm the selection or LEFT
to keep the current setting.
Control
Protocol
F
B
C
F
D
Repeat on DMX
It lets you enable the transmission of the Ethernet protocol by DMX signal
to all the connected projectors.
1) Press
the current setting appears on the display.
2) Use the UP
and DOWN
keys to select one of the following settings:
- Disabled: DMX transmission disabled.
- Enabled on primary: DMX transmission enabled.
3) Press
to confirm the selection or LEFT
to keep the current setting.
Repeat on
DMX
F
B
C
F
D
Universe
It lets you assign the “Universe” number to be assigned to a series of
projectors.
1) Press
– the current Universe address appears on the display.
2) Use the UP
, DOWN
, RIGHT
keys to set the Universe
address.
3) Press
to confirm the selection or LEFT
to keep the current
setting.
Universe
F
F
A.LEDA WASH
E
8
B
C
E
D
OPTIONS MENU
Option
Pan / Tilt
Invert
Pan
PAN / TILT
Invert pan
Used for reversing Pan movement.
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable (Off)
PAN inversion.
3) Press
to confirm the selection or LEFT
to keep current
settings.
On
Off
F
B
C
F
Invert
Tilt
D
Invert tilt
Used for reversing tilt movement.
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable (Off)
Tilt inversion.
3) Press
to confirm the selection or LEFT
to keep current
settings.
On
Off
F
B
C
F
Swap
Pan-Tilt
D
Swap Pan-Tilt
Used for swapping Pan and Tilt channels (as well as Pan fine and Tilt fine).
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable (Off)
Pan and Tilt channel swap.
3) Press
to confirm the selection or LEFT
to keep current
settings.
On
Off
F
B
C
F
Encoder
Pan-Tilt
D
Encoder Pan-Tilt
Used for enabling the Pan / Tilt encoders.
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable (Off)
Pan / Tilt encoders.
3) Press
to confirm the selection or LEFT
to keep current
settings.
On
F
Off
B
C
F
Silent
mode
D
SILENT MODE
It lets you select the “Silent Mode” from the two available.
1) Press
the current setting appears on the display.
2) Use the UP
and DOWN
keys to select one of the following
settings:
Standard: Maximum speed and consequently maximum effects noise
level.
Quiet: reduces the speed of some effects, thereby reducing their noise
level.
3) Press
to confirm the selection or LEFT
to keep the current
setting.
Standard
F
Quiet
B
C
F
D
DISPLAY
Used for automatically reduce brightness on the display after about 30
seconds in idle.
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable
(Off) the decreasing of display brightness.
to confirm the selection or LEFT
to keep current
3) Press
settings.
On
Display
Off
F
B
C
F
Special
Functions
D
SPECIAL FUNCTIONS
Pan / Tilt speed
Lets you select two different Pan and Tilt speeds.
- the current setting appears on the display.
1) Press
2) Use the UP
and DOWN
keys to select one of the following
settings:
- Normal
- Fast
to confirm the selection or LEFT
to keep current
3) Press
settings.
Pan / Tilt
speed
F
F
B
C
D
Continue
A.LEDA WASH
9
➔
Option
Special
Functions
Dimmer Curve
Lets you select four different Dimmer channel curves.
- the current setting appears on the display.
1) Press
and DOWN
keys to select one of the following
2) Use the UP
settings:
- Curve 1
- Curve 2
- Curve 3
- Curve 4
to confirm the selection or LEFT
to keep current settings.
3) Press
Dimmer
Curve
F
B
C
F
D
RGB Gamma
Lets you select three different RGBW gamma curves.
- the current setting appears on the display.
1) Press
2) Use the UP
and DOWN
keys to select one of the following
settings:
- Gamma 1.0
- Gamma 1.5
- Gamma 2.0
to confirm the selection or LEFT
to keep current settings.
3) Press
RGB
Gamma
F
B
C
F
D
Halogen Mode
Lets you select five different halogen lamp simulations.
- the current setting appears on the display.
1) Press
and DOWN
keys to select one of the following
2) Use the UP
settings:
- Halogen OFF
- Halogen Lamp 1
- Halogen Lamp 2
- Halogen Lamp 3
- Halogen Lamp 4
- Halogen Lamp 5
to confirm the selection or LEFT
to keep current settings.
3) Press
Halogen
Mode
F
B
C
F
Setting
Default
Preset
SETTING
Used to save 3 different settings of the items in the options menu and
relative submenus.
- “Default preset” appears on the display.
1) Press
and DOWN
keys to select one of the following
2) Use the UP
configurations:
- Default preset (*)
- User preset 1
- User preset 2
- User Preset 3
- “Load preset X” appears on the display.
3) Press
and DOWN
keys to select:
4) Use the UP
- Load preset X to recall a previously stored configuration.
- Save to preset X to store the current configuration.
a confirmation message (Are you sure?) appears on the display.
5) Select YES to confirm the selection or NO to keep the current setting
and return to the next higher level.
(*) DEFAULT PRESET
Used for restoring default values on all options menu items and relevant
submenus.
, a confirmation message (Are you sure?) appears on the
1) Press
display.
2) Select YES to confirm the selction or NO to keep current setting.
OPTION
DEFAULT
Invert Pan
Off
Invert Tilt
Off
Swap Pan-Tilt
Off
Encoder Pan-Tilt
On
Display
On
Silent Mode
Standard
P/T Speed
Fast
Dimmer Curve
Curve 1
RGB Gamma
Gamma 1.5
Halogen Mode
Halogen Off
Reset To
Dafault
Go Back
User
Preset 1
F
Load
Preset 1
Save To
Preset 1
User
Preset 2
F
Load
Preset 2
Save To
Preset 2
User
Preset 3
Load
Preset 3
Save To
Preset 3
F
A.LEDA WASH
D
10
B
C
B
C
INFORMATION MENU
Information
SYSTEM ERRORS
Shows a list of warnings and messages relevant to errors occurred since
the fixtures switching-on.
1) Pressing
you are allowed to reset the SYSTEM ERRORS list.
A confirmation message (Are you sure you want to clear error list ?)
appears on the display.
2) Select YES to reset the list or NO to go back.
System
Errors
F
Fixture
Hours
FIXTURE HOURS
Used for displaying projector operating hours (total and partial).
1) Press
- Hours total and partial appears on the display.
Total counter
Counts the number of projector working life hours (from manufacture to date).
Partial counter
Counts the number of partial projector working life hours since the
last reset to date.
2) Press
to reset partial projector working hours a confirmation
message (Are you sure?) appears on the display.
3) Select YES to reset partial projectors counter or NO to keep the
current setting and return to the top menu level.
Total XXX
Partial XXX
F
Reset...
F
LED ENERGY TOT
Lets you view total LED working hours.
- to display total and partial Watts/hour:
1) Press
Total
Total LED working hours from construction to date.
Partial
LED working hours from last reset to date.
2) Press
to reset the partial counter. A confirmation appears on the
screen (Are you sure?)
3) Select YES to reset the partial counter or NO to keep the current setting
and open the next menu level.
LED Energy
Tot
F
F
System
Version
Board
CPU brd
com.dev
0: PT-3f
1: Ld - Kxx
Revis.
x.x.x
x.x
x.x
x.x
Hw.rv.
x.x
Board
Diagnost.
Board
0:PT-3f
1: Ld - Kxx
Status
Good
Good
Err%
0.00
0.00
SYSTEM VERSION
Used for displaying the software and hardware version of each board
installed in the projector.
CPU brd (CPU board)
0: PT-3f (Scheda Pan / Tilt)
1: Ld - Kxx (Scheda LED)
x.x
x.x
BOARD DIAGNOSTIC
Used for displaying the status error of each board installed in the projector:
0: PT-3f (Scheda Pan / Tilt)
1: Ld - Kxx (Scheda LED)
DMX MONITOR
Used for displaying the projector DMX channel level in bit (Val) and in
percentage (Perc).
Dmx
Monitor
Fans
Monitor
Fan
PwrSp
Head
FANS MONITOR
Used for displaying the speed of each fan installed in the projector:
PwrSp (fan PSU)
Head (fan head)
Speed (RPM)
XXXX
XXXX
NETWORK PARAMS
Allows the "Network" parameters of the projector to be displayed or:
IP address: Internet Protocol address (two projectors must not have
the same IP address)
IP mask: 255.0.0.0
Mac address: Media Access Control: the projector’s Ethernet Address.
Network
params
A.LEDA WASH
11
Continue
➔
MANUAL CONTROL
Manual
Control
RESET
Used for resetting the projector.
1) Press
to reset the projectors, a confirmation message (Are you
sure ?) appears on the display.
2) Select YES to starting reset the fixture or NO to keep the current
setting and return to the top menu level.
No
Reset
Yes
F
CHANNEL
Used for setting channel levels from the projector control panel.
1) Press
- the first channel appears on the display.
2) Use the UP
and DOWN
keys to select the required channel:
3) Press
and use the UP
and DOWN
keys to select the
required DMX level (value between 0 and 255).
4) Press LEFT
to return to the top menu level.
Channel
F
B
F
D
C
B
C
TEST MENU
Test
TEST
Allows you to check the proper functioning of effects.
1) Press
to return to the top menu level.
2) Use the UP
and DOWN
keys to select the required test.
3) Press
to confirm the selection or LEFT
to keep current settings.
Test sequence:
Pan - Tilt effects (Pan & Tilt)
Colour effects (CMY / CTO / Colour wheel)
All effects
Pan-Tilt
Colour
All
F
B
F
C
D
ADVANCED MENU
Advanced
To enable the "Advanced Menu" set up the "Access code" (1234) using the
, DOWN
, RIGHT
keys.
UP
Press
- "Menu advanced" appears on the display
Code
1234
B
F
Upload
Aleda fw
Transfer the firmware on all
the connected fixtures ?
Are you sure ?
Yes/No
Setup
Model
Changing to a wrong model
may damage the fixture.
Are you sure ?
Yes/No
C
E
UP LOAD FIRMWARE
Allows you to transfer the firmware from 1 fixture to all the connected fixtures.
, a confirmation message appears on the display.
1) Press
2) Select YES to start the firmware loading or NO to keep the current setting and return to the top menu level
F
SETUP MODEL
Allows you to change the default model of projector.
1) Press
a confirmation message appears on the display.
2) Select YES to define the model of projector or NO to keep the current
setting and return to the top menu level.
F
CALIBRATION
Allows you to adjust effects from the control panel to obtain perfect uniformity between the projectors.
1) Press
- “channels” appears on the display.
2) Using the UP
and DOWN
keys, select the effect you wish to
regulate.
and use the RIGHT
, UP
and DOWN
buttons to
3) Press
make the adjustment by setting a value between 0 and 255.
4) Press
to confirm the selection or LEFT
to keep current settings and return to the top level.
Calibration
F
F
F
B
C
E
B
C
D
FACTORY DEFAULT
Allows you to restore default values of all channels (128).
1) Press
– a confirmation message appears on the display (Reset
calibration to factory default ?).
2) Select YES to reset calibration to factory default or NO to keep the
current setting and return to the top menu level.
F
A.LEDA WASH
12
9
1
2
6
3
4
5
Battery removal - Fig. 9
This product contains a rechargeable lead-acid battery. To preserve the environment, please dispose the battery at the end of its life according
to the regulation in force.
LiFePO4
A.LEDA WASH
13
MAINTENANCE
10
3
4
1
2
Opening the covers - Fig. 10
11
4
3
1
2
Removing/Assembling the lens unit - Fig. 11
NB: Apply Loctite 222 (p/n COL002) to the threads of the 3 screws (1) before tightening them. A torque of 0.3N is recommended in order to avoid
damaging the zoom movement actuators.
A.LEDA WASH
14
12
2
DIM002/001
1
Replacing the line actuator - Fig. 12
NB: It is highly recommended to use the DIM002/001 (1) template whenever it is necessary to replace one of the three Zoom movement line actuators.
DIM002/001 ensures the actuator group is centred correctly on the lens plate before tightening the 2 screws (2) that fasten the actuator in place.
A.LEDA WASH
15
OPTIONAL ACCESSORIES
A.LEDA WASH K5
13
C61452
C61453
1
2
3
Cover - Fig. 13
C61452 - Transparent cover
C61453 - Frosted cover
14
C61451
1
3
4
2
Transparent mask - Fig. 14
A.LEDA WASH
16
A.LEDA WASH K10
15
C61455
C61456
1
2
3
Cover - Fig. 15
C61455 - Transparent cover
C61456 - Frosted cover
16
C61454
1
3
4
2
Transparent mask - Fig. 16
Continue
A.LEDA WASH
17
➔
A.LEDA WASH K20
17
C61458
C61459
1
2
3
Cover - Fig. 17
C61458 - Transparent cove
C61459 - Frosted cover
18
C61457
1
3
4
2
Transparent mask - Fig. 18
A.LEDA WASH
18
TECHNICAL INFORMATION
220
(8.66")
Power supplies available
100-240V 50/60Hz
155
(6.10")
155
(6.10")
Input power
• K20 - 750VA
• K10 - 450VA
• K5 - 170VA
Max 1800VA (with 11 A.leda Wash K5 connected in parallel)
245
(9.65")
374
(14.72")
Total output
K5 - Max 2100 lumens
K10 - Max 5500 lumens
K20 - Max 10500 lumens
381
(15.00")
320
(12.60")
253
(9.96")
LED source
LED Osram Ostar RGBW - 15W
Average LED life: 50.000 h
290
(11.42")
Motors
5 (k10 & k20), 2 (k5) stepper motors, operating with
microsteps, totally microprocessor controlled.
250
(9.84")
160
(6.30")
360
(14.17")
423
(16.65")
Cooling
• High efficiency die-cast aluminium
• Forced ventilation
Inputs
DMX 512
Working position
Functioning in any position.
479
(18.86")
Movable body
• Movement by means of two stepper motors, controlled by
microprocessor.
• Automatic repositioning of PAN and TILT after accidental
movement not controlled by control unit.
• Travel:
- PAN = 540°
- TILT = 270°
358
(14.09")
253
(9.96")
380
(14.96")
360
(14.17")
160
(6.30")
460
(18.11")
476
(18.74")
IP20 protection rating
• Protected against the entry of solid bodies larger than 12mm
(0.47”).
• No protection against the entry of liquids.
CE Marking
Complies with the following European Directives
- 2006/95/EC (LVD)
- 2004/108/EC (EMC)
- 2011/65/EU (RoHS).
584
(22.99")
330
(12.99")
395
(15.55")
Weights
• K5: 7.55kg
• K10: 14.10 kg
• K20: 19.30 kg
CAUSE AND SOLUTION OF PROBLEMS
THE PROJECTOR WILL NOT SWITCH ON
ELECTRONICS NON-OPERATIONAL
PROBLEMS
DEFECTIVE PROJECTION
REDUCED LUMINOSITY
POSSIBLE CAUSES
No mains supply.
LED exhausted or defective.
Signal transmission cable faulty or disconnected.
Incorrect addressing.
Fault in the electronic circuits.
Lenses or reflector broken
Dust or grease deposited.
A.LEDA WASH
CHECKS AND REMEDIES
Check the power supply voltage.
Call an authorised technician.
Replace the cables.
Check addresses (see instructions).
Call an authorised technician.
Call an authorised technician.
Clean (see instructions).
19
CHANNEL FUNCTION
A.LEDA WASH K5
STANDARD
CHANNEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
EXTENDED
CHANNEL MODE
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
SHAPES
CHANNEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
CHANNEL MODE
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
Shape Selection
Shape Speed
Shape Smoothing
Shape Red
Shape Green
Shape Blue
Shape White
Shape Intensity
Background Intensity
Shape Transition
Shape Offset
A.LEDA WASH
CHANNEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
EXTENDED RGBW
CHANNEL MODE
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
Red LED 1
Green LED 1
Blue LED 1
Red LED 2
Green LED 2
Blue LED 2
Red LED 3
Green LED 3
Blue LED 3
Red LED 4
Green LED 4
Blue LED 4
Red LED 5
Green LED 5
Blue LED 5
Red LED 6
Green LED 6
Blue LED 6
Red LED 7
Green LED 7
Blue LED 7
CHANNEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
20
CHANNEL MODE
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
Red LED 1
Green LED 1
Blue LED 1
White LED 1
Red LED 2
Green LED 2
Blue LED 2
White LED 2
Red LED 3
Green LED 3
Blue LED 3
White LED 3
Red LED 4
Green LED 4
Blue LED 4
White LED 4
Red LED 5
Green LED 5
Blue LED 5
White LED 5
Red LED 6
Green LED 6
Blue LED 6
White LED 6
Red LED 7
Green LED 7
Blue LED 7
White LED 7
A.LEDA WASH K10
STANDARD
CHANNEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
EXTENDED
CHANNEL MODE
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
Zoom
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
CHANNEL MODE
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
Zoom
Shape Selection
Shape Speed
Shape Smoothing
Shape Red
Shape Green
Shape Blue
Shape White
Shape Intensity
Background Intensity
Shape Transition
Shape Offset
CHANNEL MODE
CHANNEL
CHANNEL MODE
Red
50
Blue LED 10
2
Red fine
51
Red LED 11
3
Green
52
Green LED 11
4
Green fine
53
Blue LED 11
5
Blue
54
Red LED 12
6
Blue fine
55
Green LED 12
7
White
56
Blue LED 12
8
White fine
57
Red LED 13
1
SHAPES
CHANNEL
CHANNEL
9
CTO
58
Green LED 13
10
Macro colour
59
Blue LED 13
11
Strobe
60
Red LED 14
12
Dimmer
61
Green LED 14
13
Dimmer Fine
62
Blue LED 14
14
Pan
63
Red LED 15
15
Pan Fine
64
Green LED 15
16
Tilt
65
Blue LED 15
17
Tilt Fine
66
Red LED 16
18
Function
67
Green LED 16
19
Reset
68
Blue LED 16
20
Zoom
69
Red LED 17
21
Red LED 1
70
Green LED 17
22
Green LED 1
71
Blue LED 17
23
Blue LED 1
72
Red LED 18
24
Red LED 2
73
Green LED 18
25
Green LED 2
74
Blue LED 18
26
Blue LED 2
75
Red LED 19
27
Red LED 3
76
Green LED 19
28
Green LED 3
77
Blue LED 19
29
Blue LED 3
30
Red LED 4
31
Green LED 4
32
Blue LED 4
33
Red LED 5
34
Green LED 5
35
Blue LED 5
36
Red LED 6
37
Green LED 6
38
Blue LED 6
39
Red LED 7
40
Green LED 7
41
Blue LED 7
42
Red LED 8
43
Green LED 8
44
Blue LED 8
45
Red LED 9
46
Green LED 9
47
Blue LED 9
48
Red LED 10
49
Green LED 10
Continue
A.LEDA WASH
21
➔
A.LEDA WASH K10
EXTENDED RGBW
CHANNEL
CHANNEL MODE
CHANNEL
CHANNEL MODE
1
Red
50
2
Red fine
51
Blue LED 8
3
Green
52
White LED 8
4
Green fine
53
Red LED 9
5
Blue
54
Green LED 9
6
Blue fine
55
Blue LED 9
7
White
56
White LED 9
8
White fine
57
Red LED 10
9
CTO
58
Green LED 10
10
Macro colour
59
Blue LED 10
11
Strobe
60
White LED 10
12
Dimmer
61
Red LED 11
13
Dimmer Fine
62
Green LED 11
14
Pan
63
Blue LED 11
15
Pan Fine
64
White LED 11
16
Tilt
65
Red LED 12
17
Tilt Fine
66
Green LED 12
18
Function
67
Blue LED 12
19
Reset
68
White LED 12
20
Zoom
69
Red LED 13
21
Red LED 1
70
Green LED 13
22
Green LED 1
71
Blue LED 13
23
Blue LED 1
72
White LED 13
24
White LED 1
73
Red LED 14
25
Red LED 2
74
Green LED 14
26
Green LED 2
75
Blue LED 14
27
Blue LED 2
76
White LED 14
28
White LED 2
77
Red LED 15
29
Red LED 3
78
Green LED 15
30
Green LED 3
79
Blue LED 15
31
Blue LED 3
80
White LED 15
32
White LED 3
81
Red LED 16
33
Red LED 4
82
Green LED 16
34
Green LED 4
83
Blue LED 16
35
Blue LED 4
84
White LED 16
36
White LED 4
85
Red LED 17
37
Red LED 5
86
Green LED 17
38
Green LED 5
87
Blue LED 17
39
Blue LED 5
88
White LED 17
40
White LED 5
89
Red LED 18
41
Red LED 6
90
Green LED 18
42
Green LED 6
91
Blue LED 18
43
Blue LED 6
92
White LED 18
44
White LED 6
93
Red LED 19
45
Red LED 7
94
Green LED 19
46
Green LED 7
95
Blue LED 19
47
Blue LED 7
96
White LED 19
48
White LED 7
49
Red LED 8
A.LEDA WASH
Green LED 8
22
A.LEDA WASH K20
STANDARD
CHANNEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
EXTENDED
CHANNEL MODE
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
Zoom
SHAPES
CHANNEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
CHANNEL MODE
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
Zoom
Shape Selection
Shape Speed
Shape Smoothing
Shape Red
Shape Green
Shape Blue
Shape White
Shape Intensity
Background Intensity
Shape Transition
Shape Offset
CHANNEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
CHANNEL MODE
CHANNEL
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
Zoom
Red LED 1
Green LED 1
Blue LED 1
Red LED 2
Green LED 2
Blue LED 2
Red LED 3
Green LED 3
Blue LED 3
Red LED 4
Green LED 4
Blue LED 4
Red LED 5
Green LED 5
Blue LED 5
Red LED 6
Green LED 6
Blue LED 6
Red LED 7
Green LED 7
Blue LED 7
Red LED 8
Green LED 8
Blue LED 8
Red LED 9
Green LED 9
Blue LED 9
Red LED 10
Green LED 10
Blue LED 10
Red LED 11
Green LED 11
Blue LED 11
Red LED 12
Green LED 12
Blue LED 12
Red LED 13
Green LED 13
Blue LED 13
Red LED 14
Green LED 14
Blue LED 14
Red LED 15
Green LED 15
Blue LED 15
Red LED 16
CHANNEL MODE
Green LED 16
Blue LED 16
Red LED 17
Green LED 17
Blue LED 17
Red LED 18
Green LED 18
Blue LED 18
Red LED 19
Green LED 19
Blue LED 19
Red LED 20
Green LED 20
Blue LED 20
Red LED 21
Green LED 21
Blue LED 21
Red LED 22
Green LED 22
Blue LED 22
Red LED 23
Green LED 23
Blue LED 23
Red LED 24
Green LED 24
Blue LED 24
Red LED 25
Green LED 25
Blue LED 25
Red LED 26
Green LED 26
Blue LED 26
Red LED 27
Green LED 27
Blue LED 27
Red LED 28
Green LED 28
Blue LED 28
Red LED 29
Green LED 29
Blue LED 29
Red LED 30
Green LED 30
Blue LED 30
Red LED 31
Green LED 31
Blue LED 31
Red LED 32
Green LED 32
Blue LED 32
Red LED 33
Green LED 33
Blue LED 33
Red LED 34
Green LED 34
Blue LED 34
Red LED 35
Green LED 35
Blue LED 35
Red LED 36
Green LED 36
Blue LED 36
Red LED 37
Green LED 37
Blue LED 37
Continue
A.LEDA WASH
23
➔
A.LEDA WASH K20
EXTENDED RGBW
CHANNEL
CHANNEL MODE
CHANNEL
CHANNEL MODE
CHANNEL
CHANNEL MODE
1
Red
57
Red LED 10
113
Red LED 24
2
Red fine
58
Green LED 10
114
Green LED 24
3
Green
59
Blue LED 10
115
Blue LED 24
4
Green fine
60
White LED 10
116
White LED 24
5
Blue
61
Red LED 11
117
Red LED 25
6
Blue fine
62
Green LED 11
118
Green LED 25
7
White
63
Blue LED 11
119
Blue LED 25
8
White fine
64
White LED 11
120
White LED 25
9
CTO
65
Red LED 12
121
Red LED 26
10
Macro colour
66
Green LED 12
122
Green LED 26
11
Strobe
67
Blue LED 12
123
Blue LED 26
12
Dimmer
68
White LED 12
124
White LED 26
13
Dimmer Fine
69
Red LED 13
125
Red LED 27
14
Pan
70
Green LED 13
126
Green LED 27
15
Pan Fine
71
Blue LED 13
127
Blue LED 27
16
Tilt
72
White LED 13
128
White LED 27
17
Tilt Fine
73
Red LED 14
129
Red LED 28
18
Function
74
Green LED 14
130
Green LED 28
19
Reset
75
Blue LED 14
131
Blue LED 28
20
Zoom
76
White LED 14
132
White LED 28
21
Red LED 1
77
Red LED 15
133
Red LED 29
22
Green LED 1
78
Green LED 15
134
Green LED 29
23
Blue LED 1
79
Blue LED 15
135
Blue LED 29
24
White LED 1
80
White LED 15
136
White LED 29
25
Red LED 2
81
Red LED 16
137
Red LED 30
26
Green LED 2
82
Green LED 16
138
Green LED 30
27
Blue LED 2
83
Blue LED 16
139
Blue LED 30
28
White LED 2
84
White LED 16
140
White LED 30
29
Red LED 3
85
Red LED 17
141
Red LED 31
30
Green LED 3
86
Green LED 17
142
Green LED 31
31
Blue LED 3
87
Blue LED 17
143
Blue LED 31
32
White LED 3
88
White LED 17
144
White LED 31
33
Red LED 4
89
Red LED 18
145
Red LED 32
34
Green LED 4
90
Green LED 18
146
Green LED 32
35
Blue LED 4
91
Blue LED 18
147
Blue LED 32
36
White LED 4
92
White LED 18
148
White LED 32
37
Red LED 5
93
Red LED 19
149
Red LED 33
38
Green LED 5
94
Green LED 19
150
Green LED 33
39
Blue LED 5
95
Blue LED 19
151
Blue LED 33
40
White LED 5
96
White LED 19
152
White LED 33
41
Red LED 6
97
Red LED 20
153
Red LED 34
42
Green LED 6
98
Green LED 20
154
Green LED 34
43
Blue LED 6
99
Blue LED 20
155
Blue LED 34
44
White LED 6
100
White LED 20
156
White LED 34
45
Red LED 7
101
Red LED 21
157
Red LED 35
46
Green LED 7
102
Green LED 21
158
Green LED 35
47
Blue LED 7
103
Blue LED 21
159
Blue LED 35
48
White LED 7
104
White LED 21
160
White LED 35
49
Red LED 8
105
Red LED 22
161
Red LED 36
50
Green LED 8
106
Green LED 22
162
Green LED 36
51
Blue LED 8
107
Blue LED 22
163
Blue LED 36
52
White LED 8
108
White LED 22
164
White LED 36
53
Red LED 9
109
Red LED 23
165
Red LED 37
54
Green LED 9
110
Green LED 23
166
Green LED 37
55
Blue LED 9
111
Blue LED 23
167
Blue LED 37
56
White LED 9
112
White LED 23
168
White LED 37
A.LEDA WASH
24
NOTE: On conclusion of resetting in case of absence of DMX signal, Pan & Tilt move to the "Home" position (Pan 50% - Tilt 50%) all the others channels stay at 0%.
• C.T.O.
• RED – GREEN - BLUE - WHITE
BIT
255
0
BIT
EFFECT
COLOUR INSERTED
COLOUR EXCLUDED
• RED FINE – GREEN FINE – BLUE FINE – WHITE FINE
BIT
EFFECT
255
0
EFFECT
255
2500
250
2600
246
2700
242
2800
237
2900
233
3000
228
3100
224
3200
219
3300
215
3400
210
3500
206
3600
201
3700
197
3800
192
3900
188
4000
184
4100
179
4200
175
4300
170
4400
166
4500
161
4600
157
4700
152
4800
148
4900
144
5000
139
5100
135
5200
130
5300
126
5400
121
5500
117
5600
112
5700
108
5800
103
5900
99
6000
95
6100
90
6200
86
6300
81
6400
77
6500
72
6600
68
6700
63
6800
59
6900
54
7000
50
7100
46
7200
41
7300
37
7400
32
7500
28
7600
23
7700
19
7800
14
7900
10
8000
0-9
UNUSED RANGE
Note: If CTO channel is active, the WHITE channel is disabled.
Continue
A.LEDA WASH
25
➔
• MACRO COLOUR
LEE
REFERENCE
COLOUR
BIT VALUE
R G B W
207-255
197
Alice Blue
128
255
143
0
191-206
181
Congo Blue
77
0
255
0
184-190
174
Dark Steel Blue
181
255
95
0
180-183
170
Deep lavender
255
168
64
0
179
169
Lilac Tint
255
199
49
0
175-178
165
Daylight Blue
82
214
90
0
BIT
(25 flash/sec)
MACRO
BIT
• STOP / STROBE
OPEN
RANDOM FAST STROBE
RANDOM MEDIUM STROBE
RANDOM SLOW STROBE
OPEN
FAST PULSATION (25 flash/sec)
108
104 - 107
103
SLOW PULSATION
OPEN
FAST STROBE (25 flash/sec)
4
0-3
SLOW STROBE (1 flash/sec)
CLOSED
(0,5 flash/sec)
174
164
Flame Red
255
46
2
0
172-173
162
Bastard Amber
255
181
28
0
168-171
158
Deep Orange
222
84
0
0
162-167
152
Pale Gold
253
171
26
0
157-161
147
Apricot
255
143
13
0
151-156
141
Bright Blue
0
255
87
0
149-150
139
Primary Green
77
255
0
0
147-148
137
Special lavender
219
197
79
0
146
136
Pale Lavender
255
197
61
0
145
135
Deep Golden Amber
255
58
0
0
142-144
132
Medium Blue
0
255
143
0
138-141
128
Bright Pink
255
53
36
0
136-137
126
Mauve
227
41
56
0
134-135
124
Dark Green
84
255
13
0
131-133
121
Leaf Green
206
255
0
0
129-130
119
Dark Blue
0
186
255
0
128
118
Light Blue
74
255
82
0
127
117
Steel Blue
206
255
56
0
126
116
Med Blu Green
206
255
56
0
125
115
Peacock Blue
51
255
51
0
123-124
113
Magenta
255
20
15
0
121-122
111
Dark Pink
255
109
33
0
120
110
Middle Rose
217
130
28
0
119
109
Light Salmon
255
138
31
0
118
108
English Rose
255
148
23
0
117
107
Light Rose
255
141
31
0
115-116
105
Orange
255
122
0
0
114
104
Deep Amber
255
166
0
0
BIT
113
103
Straw
230
160
0
69
255
112
102
Light Amber
237
163
0
0
110-111
100
Spring Yellow
245
202
0
0
100-109
90
Dark yellow green
41
219
0
0
89-99
79
Just Blue
0
194
130
0
78-88
68
Sky Blue
0
255
135
0
68-77
58
Lavender
243
117
133
199
62-67
52
Light Lavender
243
117
39
197
49-61
39
Pink Carnation
255
107
0
130
46-48
36
Medium Pink
255
87
0
107
45
35
Light Pink
255
112
0
141
35-44
25
Sunrise Red
255
83
2
0
32-34
22
Dark Amber
255
65
0
0
31
21
Gold Amber
255
100
0
0
30
20
Medium Amber
255
135
0
0
29
19
Fire
255
56
0
0
27-28
17
Surprise Peach
198
114
9
0
23-26
13
Straw Tint
152
115
9
0
20-22
10
Medium Yellow
156
126
0
0
0
0
0
0
19
Black
18
White 5000°K
255
137
0
193
17
White 3700°K
255
201
25
255
16
White 7000°K
216
237
61
255
15
Magenta
255
0
255
0
14
Yellow
255
255
0
0
13
Cyan
0
255
255
0
12
Blue
0
0
255
0
11
Green
0
255
0
0
10
Red
255
0
0
0
0-9
Macro color OFF
A.LEDA WASH
EFFECT
252 - 255
239 - 251
226 - 238
213 - 225
208 - 212
207
• DIMMER
BIT
255
0
EFFECT
FULL LIGHT
NO LIGHT
• DIMMER FINE
0
26
EFFECT
• PAN
Operation with option InvertPan Off
(Tilt conventionally represented at 14% and option Invert Tilt
G
• TILT
Operation with option InvertPan Off
(Tilt conventionally represented at 14% and option Invert Tilt
G
GOff)
GOff)
BIT
BIT
255
255
0-255 Bit: 2.65 sec (K20)
0-255 Bit: 2.01 sec (K10)
0-255 Bit: 1.41 sec (K5)
0-255 Bit: 1.45 sec (K20)
0-255 Bit: 0.87 sec (K10)
0-255 Bit: 0.80 sec (K5)
0
0
G
G
Operation with option InvertPan On
(Tilt conventionally represented at 14% and option Invert Tilt
Operation with option InvertPan On
(Tilt conventionally represented at 14% and option Invert Tilt
GOff)
GOff)
BIT
BIT
255
255
0-255 Bit: 1.45 sec (K20)
0-255 Bit: 0.87 sec (K10)
0-255 Bit: 0.80 sec (K5)
0-255 Bit: 2.65 sec (K20)
0-255 Bit: 2.01 sec (K10)
0-255 Bit: 1.41 sec (K5)
0
0
• TILT FINE
Operation with option InvertPan Off
(Tilt conventionally represented at 14% and option Invert Tilt
• PAN FINE
Operation with option InvertPan Off
(Tilt conventionally represented at 14% and option Invert Tilt
G
G
GOff)
BIT
BIT
255
255
0
0
G
GOff)
G
Operation with option InvertPan On
(Tilt conventionally represented at 14% and option Invert Tilt
Operation with option InvertPan On
(Tilt conventionally represented at 14% and option Invert Tilt
GOff)
GOff)
BIT
BIT
255
255
0
0
Continue
A.LEDA WASH
27
➔
• FUNCTION
DIMMER CURVE 4 - S
BIT
251 – 255
103 – 250
98 – 102
93 – 97
88 – 92
83 – 87
78 – 82
73 – 77
68 – 72
63 – 67
58 – 62
53 – 57
48 – 52
43 – 47
38 – 42
25 – 37
12 – 24
0 – 11
EFFECT
Reset to defult
Unused Range
Halogen Lamp Simulation, type 5 (2500 W)
Halogen Lamp Simulation, type 4 (2000 W)
Halogen Lamp Simulation, type 3 (1200 W)
Halogen Lamp Simulation, type 2 (1000 W)
Halogen Lamp Simulation, type 1 (750W)
Halogen Lamp Simulation OFF (Default)
RGBW Gamma curve 3 – gamma = 2.0
RGBW Gamma curve 2 – gamma = 1.5 (Default)
RGBW Gamma curve 1 – gamma = 1.0
Dimmer Curve 4
Dimmer Curve 3 (Default)
Dimmer Curve 2
Dimmer Curve 1
Pan Tilt Normal
Pan Tilt Fast (Default)
Function off
The functions are actived passing through the “unused range” and staying 5 seconds
in necessary level.
Last selected function still active. Enable setting a new function.
DIMMER CURVE 1 - GAMMA 1 LINEAR
• RESET
BIT
255
EFFECT
COMPLETE RESET
Complete reset is activated passing throug the unused range
and staying 5 seconds in complete reset levels
128
127
COMPLETE RESET
PAN / TILT RESET
Pan / Tilt reset is activated passing throug the unused range
and staying 5 seconds in Pan / Tilt reset levels
77
76
PAN / TILT RESET
ZOOM RESET
Effects reset is activated passing throug the unused range
and staying 5 seconds in Effects reset levels.
26
25
0
UNUSED RANGE
* Automatic gamma is calculated based on background intensity to auto-adapt the
shape’s fade.
DIMMER CURVE 2 - GAMMA 1,5
DIMMER CURVE 3 - GAMMA 2,0
A.LEDA WASH
ZOOM RESET
28
SHAPE SELECTION - SHAPE SPEED - SHAPE OFFSET
BIT
32-255
31
30
29
28
27
26
25
24
SHAPE SELECTION
Reserved
Two rotating arcs of different colors and
direction
Two rotating arcs of different colors
Two rotating bars of different colors
Triangle
Half moon
Bar (2 arms)
Fan (3 arms)
Rainbow 2, fixed speed with variable
color offset.
On
K5
On
K10
No
No
Yes
Yes
On
K20
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
RANDOM
COLORS *1
SHAPE OFFSET
N.a.
N.a.
N.a.
Yes
Yes
Yes
Yes
Yes
Yes
N.a.
0-126 =
0-255 → angle offset from 0 to 360°
Yes
Yes
23
Rainbow 1, variable speed.
Yes
Yes
Yes
Yes
22
Random pixels with variable density
and speed
Random pixels distribuited on
many fixtures
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
21
SHAPE SPEED
max to min speed,
c.cw rotation
127-128 = STOP
129-255 = min to max speed,
cw rotationt"
0-126 = c.cw rotation
127-128 = STOP
129-255 = cw rotationt
The value 0-126 or 129-255 change
the rainbow angle offset (the orange
starting angle).
0-126 = max to min speed,
c.cw rotation
127-128 = STOP
129-255 = min to max speed,
cw rotationt
N.a.
0-255 → angle offset from 0 to 360°
0-255 → select pixel density
0-126 = max to min speed,
Instant-on + fadeout.
127-128 = STOP.
129-255 = min to max speed,
FadeIn + FadeOut.
0-255 → select random distribution
from 2 up to 20 fixtures
Fade or snap depending on fade
channel.
20
19
Ring with variable radius, filled.
Ring with variable radius
Yes
Yes
Yes
Yes
Yes
Yes
N.a.
N.a.
18
17
Ring Open/Close (close/open) Filled
Ring Open/Close (close/open)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0-126 =
16
15
Ring Opening (Closing) Filled
Ring Opening (Closing)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0-126 =
max to min speed,
Closing effect
127-128 = STOP
129-255 = min to max speed,
Opening effect
0-9 → continuous
10-255 → random distribution of flash
from 2 to 20 fixtures"
14
13
12
11
10
9
8
0-7
Ring 1 + 4
Ring 1 + 3
Ring 1 + 2
Ring 4
Ring 3
Ring 2
Ring 1
Macro OFF
No
No
Yes
No
No
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
N.a.
N.a.
N.a.
N.a.
N.a.
N.a.
0-255 =
0=
255 =
radius
minimum
maximum
N.a.
0-255 → angle offset from 0 to 360°
max to min speed,
Start closed
127-128 = STOP
129-255 = min to max speed,
Start opened"
*1: Random colors activation with foreground R,G,B,W = 0
Continue
A.LEDA WASH
29
➔
Macro Off
DMX channel value: from 0 to 7.
No shape effects activated. Turns off any previously selected shape.
Static Rings
DMX channel value: from 8 to 14.
The ring or rings used by the macro are turned on with the foreground colour (Shape Red+Shape Green+Shape blue+Shape White).
Avaliable combinations: Ring 1 On, Ring 2 On, Ring 3 On (Aleda K10, K20 only), Ring 4 On (Aleda K20 only),Ring 1+2 On,
Ring 1+3 On (Aleda K10, K20 only), Ring 1+4 On (Aleda K20 only).
Dynamic Rings
DMX channel
Dynamic Rings
DMX channel value: From 15 to 18.
The rings used by the macro are turned on sequentially, simulating an opening , closing or both.
The Shape Speed channel increases the speed from 126 (min speed) to 0 (max speed) for the closing and closing/opening effects and from 129 (min
speed) to 255 (max speed) for the opening and opening/closing effects. With DMX value = 127 or 128 the macro stays still.
The Shape Offset channel defines the macro effect distribution over a number of fixtures (affects also the behavior of a single fixture)
Dmx values from 0 to 9: continous distribution;
Dmx values from 10 to 255 random distribution of flash from 2 to 20 fixtures.
If foreground colors are all set to 0, the Random-Colors mode is activated.
The color used by the macro changes at every restart.
Rings with variable radius
DMX channel value: 19 - 20.
The Shape Speed channel defines the ring radius: 0 = min, 255 = max.
Random pixels
DMX
Random pixels
DMX channel value: 21 – 22.
Leds are turned on and off randomly.
The Shape Speed channel increases the speed and defines the fade effect for the leds: from 126 (min speed) to 0(max speed) with a Instant-on/ fade-out
led effect, and from 129 (min speed) to 255 (max speed)with a fade-in + fade-out led effect. At a DMX value of 127 and 128 the macro stays still.
For macro 21 the Shape Offset channel defines leds random distribution from 0 (2 fixtures) to 255 over a set of fixtures (20 fixtures).
For macro 22 the Shape Offset channel defines pixels density from 0 (min density) to 255 (max density).
If foreground colors are all set to 0 the Random-Colors mode is activated.
The Shape Smoothing channel adjusts the fading effect applied to the macro movement
Rainbows
DMX channel value: 23 – 24 .
It simulates a rainbow effect.
The Shape Speed channel increases the speed and defines the rotation : from 126 (min speed) to 0 (max speed) counter clock wise rotation and from 129
(min speed) to 255 (max speed) clock wise rotation. With DMX value 127 or 128 the macro stays still.
For the macro 24 (Rainbow with fixed speed) the Shape Speed channel also defines angle offset (the orange sector starting angle).
Rotating shapes
DMX channel value: from 25 to 31.
Shapes avaliable: Fan (3 arms), Bar (2 arms), Half Moon, Triangle, Two rotating bars of different colors, Two rotating arcs of different colors, Two rotating
arcs of different colors and direction.
The Shape Speed channel increases the speed and defines the rotation : from 126 (min speed) to 0 (max speed) counter clock wise rotation and from 129
(min speed) to 255 (max speed) clock wise rotation. With DMX value 127 or 128 the macro stays still.
The Shape Offset channel defines the angle offset from 0 (0 degree) to 255 (360 degree).
A.LEDA WASH
30
• SHAPE SMOOTHING
• ZOOM
BIT
BIT
255
EFFECT
246-255
245
244
243
EFFECT
WIDE BEAM
Smooth, fading curve with automatic gamma *
Smooth, fading curve gamma 2
Smooth, fading curve gamma 1,993
Smooth, fading curve gamma 1,986
0-255 Bit: 0.68 sec (K20)
0-255 Bit: 0.69 sec (K10)
Smooth, fading curve gamma 0,513
Smooth, fading curve gamma 0,506
Smooth, fading curve gamma 0,5
Snap
18
17
16
0-15
0
* Automatic gamma is calculated based on background intensity to auto-adapt the
shape’s fade.
NARROW BEAM
DMX BIT
Fading gamma
16
• SHAPE R G B W
BIT
255
0,500
Gamma Curve
EFFECT
1,000
COLOUR INSERTED
0,900
0,800
pixel power
0,700
0,600
0,500
0,400
0,300
0,200
0,100
0,000
0,100
0,200
0,300
0,400
0,500
0,600
0,700
0,800
0,900
1,000
0,700
0,800
0,900
1,000
0,700
0,800
0,900
1,000
pixel colour distribution
0
COLOUR EXCLUDED
Fading gamma
DMX BIT
92
• SHAPE INTENSITY
BIT
255
0,997
Gamma Curve
EFFECT
1,000
COLOUR INSERTED
0,900
0,800
pixel power
0,700
0,600
0,500
0,400
0,300
0,200
0,100
0,000
0,100
0,200
0,300
0,400
0,500
0,600
pixel colour distribution
0
COLOUR EXCLUDED
DMX BIT
Fading gamma
245
• BACKGROUND INTENSITY
2,000
Gamma Curve
BIT
255
EFFECT
1,000
COLOUR INSERTED
0,900
0,800
pixel power
0,700
0,600
0,500
0,400
0,300
0,200
0,100
0,000
0,100
0,200
0,300
0,400
0,500
0,600
pixel colour distribution
0
COLOUR EXCLUDED
Continue
A.LEDA WASH
31
➔
• SHAPE TRANSITION
BIT
FADING TIME
BIT
255
4000 ms
199
2600 ms
143
1480 ms
87
650 ms
254
3970 ms
198
2580 ms
142
1460 ms
86
640 ms
253
3950 ms
197
2560 ms
141
1440 ms
85
630 ms
252
3920 ms
196
2530 ms
140
1430 ms
84
620 ms
251
3890 ms
195
2510 ms
139
1410 ms
83
610 ms
250
3860 ms
194
2490 ms
138
1390 ms
82
600 ms
249
3840 ms
193
2470 ms
137
1380 ms
81
590 ms
248
3810 ms
192
2450 ms
136
1360 ms
80
570 ms
247
3780 ms
191
2420 ms
135
1340 ms
79
560 ms
246
3760 ms
190
2400 ms
134
1330 ms
78
550 ms
245
3730 ms
189
2380 ms
133
1310 ms
77
540 ms
244
3700 ms
188
2360 ms
132
1290 ms
76
530 ms
243
3680 ms
187
2340 ms
131
1280 ms
75
520 ms
242
3650 ms
186
2320 ms
130
1260 ms
74
510 ms
241
3630 ms
185
2290 ms
129
1240 ms
73
500 ms
240
3600 ms
184
2270 ms
128
1230 ms
72
490 ms
239
3570 ms
183
2250 ms
127
1210 ms
71
480 ms
238
3550 ms
182
2230 ms
126
1200 ms
70
470 ms
237
3520 ms
181
2210 ms
125
1180 ms
69
460 ms
236
3500 ms
180
2190 ms
124
1160 ms
68
450 ms
235
3470 ms
179
2170 ms
123
1150 ms
67
440 ms
234
3440 ms
178
2150 ms
122
1130 ms
66
430 ms
233
3420 ms
177
2130 ms
121
1120 ms
65
420 ms
232
3390 ms
176
2110 ms
120
1100 ms
64
410 ms
231
3370 ms
175
2090 ms
119
1090 ms
63
400 ms
230
3340 ms
174
2070 ms
118
1070 ms
62
390 ms
229
3320 ms
173
2050 ms
117
1060 ms
60-61
380 ms
228
3290 ms
172
2020 ms
116
1040 ms
59
370 ms
227
3270 ms
171
2000 ms
115
1030 ms
58
360 ms
226
3240 ms
170
1980 ms
114
1010 ms
57
350 ms
225
3220 ms
169
1960 ms
113
1000 ms
56
340 ms
224
3190 ms
168
1950 ms
112
980 ms
54-55
330 ms
223
3170 ms
167
1930 ms
111
970 ms
53
320 ms
222
3140 ms
166
1910 ms
110
950 ms
52
310 ms
221
3120 ms
165
1890 ms
109
940 ms
51
300 ms
220
3100 ms
164
1870 ms
108
930 ms
49-50
290 ms
219
3070 ms
163
1850 ms
107
910 ms
48
280 ms
218
3050 ms
162
1830 ms
106
900 ms
47
270 ms
217
3020 ms
161
1810 ms
105
880 ms
45-46
260 ms
216
3000 ms
160
1790 ms
104
870 ms
44
250 ms
215
2970 ms
159
1770 ms
103
860 ms
42-43
240 ms
214
2950 ms
158
1750 ms
102
840 ms
41
230 ms
213
2930 ms
157
1730 ms
101
830 ms
39-40
220 ms
212
2900 ms
156
1710 ms
100
820 ms
37-38
210 ms
211
2880 ms
155
1700 ms
99
800 ms
35-36
200 ms
210
2860 ms
154
1680 ms
98
790 ms
34
190 ms
209
2830 ms
153
1660 ms
97
780 ms
32-33
180 ms
208
2810 ms
152
1640 ms
96
770 ms
30-31
170 ms
207
2790 ms
151
1620 ms
95
750 ms
27-29
160 ms
206
2760 ms
150
1600 ms
94
740 ms
25-26
150 ms
205
2740 ms
149
1590 ms
93
730 ms
22-24
140 ms
204
2720 ms
148
1570 ms
92
710 ms
19-21
130 ms
203
2690 ms
147
1550 ms
91
700 ms
16-18
120 ms
202
2670 ms
146
1530 ms
90
690 ms
11-15
110 ms
201
2650 ms
145
1510 ms
89
680 ms
5-10
100 ms
200
2620 ms
144
1500 ms
88
670 ms
0-4
No fade
A.LEDA WASH
BIT
FADING TIME
32
FADING TIME
BIT
FADING TIME
A.LEDA WASH K5
A.LEDA WASH K10
LED reference number for pixel mapping
TILT: channel 16 at 80%
LED reference number for pixel mapping
TILT: channel 16 at 80%
13
14
12
15
4
11
LED
3
2
1
17
2
7
18
9
8
7
A.LEDA WASH K20
LED reference number for pixel mapping
TILT: channel 16 at 80%
28
29
30
27
26
13
14
4
5
31
12
15
25
11
32
16
LED
3
24
6
1
33
10
17
2
23
7
9
22
34
18
8
19
20
37
21
A.LEDA WASH
16
6
10
6
1
LED
3
5
4
5
35
36
33
19
A.LEDA WASH
34
A.LEDA WASH
35
IST004/001 – EN - Rev.0 09/13
CLAY PAKY S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311 - Fax +39-035-301876 - www.claypaky.it