Makita 2030S Instruction manual

312 mm (12-9/32")MODEL 2030s
INSTRUCTION MANUAL
DOUBLE
INSULATION
SPECIFICAT10 NS
Cutting width
Max. c u t t i n g d e p t h
Feed rateimin
Imml
Imml
lml
3.0 (118")f o r
312 (12-9/32"1
Auto feed
stock
size lmml
Auto feed
290 x 500 I1 1-13/32"x 19-11/16")
Manual feed
155 x 900 (6-118"x 35~7116")
No load speed
9,000
(RPMI
stock
~~
240 15-29/32" 9-7/16"]wide
~
10.5(34.5ft.1
240 ~- 312 (9.7116" - 12-9/32"]w i d e
-
3 0 (118")
155 16-1/8"1
Table
~
1 5 (1/16"1for stock 150
1.0 13/64']for
Manual feed
0 - 150 (0'' 5-29132"1 wide
Overall dimensions
Fence size (mml
~
615 x 100 124~7132"x 3~15116")
(W x L x HI lmml
704 x 900 x 574 (27~23132"
x 35~7116"x 22~19132")
Stock height
lmml
4 - 160 15/32" - 6-5/16")
~
Net weight
44 kg 197 lbsl
For Your Own Safety Read Instruction
Manual Before Operating Planer-Jointer
GENERAL SAFETY PRECAUTIONS
(For All Tools)
1. KNOW YOUR POWER TOOL. Read the owner’s manual carefully. Learn the
tools applications and limitations, as well as the specific potential hazards
peculiar t o it.
2. KEEP GUARDS IN PLACE and in working order.
3.REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o
see that keys and adjusting wrenches are removed from tool before turning
it on.
4. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
5. DON‘T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp
or wet locations, or expose them t o rain. Keep work area well lighted.
6. KEEP CHILDREN AWAY. All visitors should be kept safe distance from work
area.
7. MAKE WORKSHOP KID PROOF w i t h padlocks, master switches, or by
removing starter keys.
8. DON’T FORCE TOOL. It will do the job better and safer at the rate for which
it was designed.
9. USE RIGHT TOOL. Don’t force tool or attachment t o do a job for which it
was n o t designed.
IO. WEAR
PROPER APPAREL. Wear no loose clothing, gloves, neckties, rings,
bracelets, or other jewelry which may get caught in moving parts. Nonslip
footwear is recommended. Wear protective hair covering t o contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting
operation is dusty. Everyday eyeglasses only have impact resistant lenses,
they are NOT safety glasses.
12. SECURE WORK. Use clamps or a vise t o hold work when practical. It‘s safer
than using your hand and it frees both hands t o operate tool.
13. DON’T OVERREACH. Keep proper footing and balance at all times.
14.MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and
safest performance. Follow instructions for lubricating and changing accessories.
15. DISCONNECT TOOLS before servicing; when changing accessories such as
blades, bits, cutters, and the like.
2
16. EXTENSION CORDS. Make sure your extension cord is in good condition.
When using an extension cord, be sure t o use one heavy enough t o carry
the current your product will draw. A n undersized cord will cause a drop in
line voltage resulting in loss of power and overheating. Table 1 shows the
correct size t o use depending on cord length and nameplate ampere rating.
If i n doubt, use the next heavier gage. The smaller the gage number, the
heavier the cord.
Minimum aaae for cord"
Total length of cord in feet
Volts
120V
240 V
Ampere Rating
More Than
0
Not
More Than
5 0 ft.
100 ft.
1 5 0 ft.
100 ft.
200 ft.
300 ft.
AWG
14
12
12
Not Recommended
6
18
16
16
12
18
16
16
16
14
14
16
14
12
6
I
25ft.
5 0 ft.
aOnly the applicable parts of the Table need to be included. For instance, a 120-volt product need not
include the 240-volt heading.
17. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is
in off position before plugging in.
18. USE RECOMMENDED ACCESSORIES. Consult the owner's manual for
recommended accessories. The use of improper accessories may cause risk
of injury t o persons.
19. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or
if the cutting tool is accidentally contacted.
20. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other
part that is damaged should be carefully checked t o determine that it will
operate properly and perform its intended function - check for alignment
of moving parts, binding of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced.
21. DIRECTION OF FEED. Feed work into a blade or cutter against the direction
of rotation of the blade or cutter only.
22. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don't
leave tool until it comes t o a complete stop.
23.PROPER GROUNDING. This tool should be grounded while in use t o protect
the operator from electric shock.
24. POLARIZED PLUGS. To reduce the risk of electric shock, this equipment has
a polarized plug (one blade is wider than the other). This plug will f i t in a
polarized outlet only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician t o install the
proper outlet. Do not change the plug in any way.
3
VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle,
outlet, etc.) be sure the voltage supplied is the same as that specified on the
nameplate of the tool. A power source w i t h voltage greater than that specified
for the tool can result in SERIOUS INJURY t o the user - as well as damage t o
the tool. If in doubt, DO NOT PLUG I N THE TOOL. Using a power source w i t h
voltage less than the nameplate rating is harmful t o the motor.
ADDITIONAL SAFETY RULES
FOR JOINTER & AUTO-PLANER
1. Don't use the t o o l in presence of flammable liquids or gases.
2. Handle the blades very carefully.
cracks or damage before operation. Replace
cracked or damaged blades immediately.
3. Check the blades carefully for
4. Be sure the planer blade installation bolts are securely tightened before
operating.
5. Sharpen both blades evenly, or replace both blades or both cutterhead covers
at the same time.
6. Remove nails and clean the workpiece before cutting. Nail, sand or other
matter can cause blade damage.
7. Make sure the blade is not contacting workpiece before the switch is turned
on.
8. Wait until the blades attain full speed before cutting.
9. Keep hands away from rotating parts.
IO. Stop operation immediately if you notice anything abnormal.
11. Always switch o f f and wait for blades t o come to a complete stop before
adjusting any parts, cleaning out chips or approaching the blade.
12. Never stick your finger into the chip chute. Chute may jam w h e n cutting
damp wood. Turn off the planer-jointer and then clean out chips w i t h a stick.
13. Do not touch blades right after operation, they may be extremely hot and
could burn your skin.
14. Don't abuse cord. Never yank cord t o disconnect from receptacle. Keep cord
from heat, oil and sharp edges.
15. Do not use auto-planer and jointer at the same time. Overloading of the motor
can occur.
4
FOR JOINTER
1. Maintain the proper relationships of infeed and outfeed table surfaces and
cutterhead blade path.
2. Do not perform jointing operations on material shorter than 140 m m (5-1/2
inches), narrower than 19 m m ( 3 / 4 inch), or less than 12.7 m m (112 inch) thick.
3. Do not perform planing operations on material shorter than 140 m m (5-1/2
inches), narrower than 19 m m ( 3 / 4 inch), wider than 155 m m (6-1/8 inches)
or thinner than 12.7 m m (112 inch).
4. Support the workpiece adequately at all times during operation; maintain
control of the work at all times.
5. Do not back the work toward the infeed table.
6. Do not attempt t o perform an abnormal or little-used operation without study
and the use of adequate hold-down/push blocks, jigs, fixtures, stops and the
like.
FOR AUTO-PLANER
1. Two or more pieces of narrow but similar thickness stock can be passed
through the auto-planer side by side.
However, allow some spacing between the stock t o permit the feed rollers
t o grip the thinnest piece.
Otherwise, a slightly thinner piece could be kicked back by the cutterhead.
2. Determine the depth of cut according t o the table shown on the front of the
tool. Do not attempt t o cut more than the specified amount i n one pass.
WARNING
For Your O w n Safety, Read Instruction Manual Before Operating Jointer
1. Wear eye protection.
2. Never perform jointing or planing operation w i t h cutter head or drive guard
removed.
3. Never make jointing or planing cut deeper than 3 m m (118 inch).
4. Always use hold-down/push blocks for jointing material narrower than 76.2
m m (3inches), or planing material thinner than 76.2 m m (3inches).
SAVE THESE INSTRUCTIONS.
5
Movement and transport of planer-jointer
When moving the tool, hold i t as shown in
the figure. When transporting it by vehicle,
secure with a rope or other substantial
means to prevent tipping or movement.
Positioning the planer-jointer
Locate the tool in a well lit and level place
where you can maintain good footing and
balance. Bolt i t to the workbench using
the bolt holes provided in the base.
When locating it without bolting, use the
stays provided to help maintain its stability.
Remove the two bolts which secure the
stays. Extend the stays by one bolt hole
and secure them using the bolts.
Installing the crank handle
Install the crank handle using the socket wrench provided.
Switch action
CAUTION :
Before plugging in the tool, always be sure that the tool is switched off.
To s t a r t the tool, insert the key and press
the ON side of the switch. To stop it, press
the OFF side.
CAUTION :
When not using the tool, remove the key
and store i t in a secure place. This prevents
unauthorized operation.
6
AUTO-PLANER FUNCTIONS:
Dimensional adjustment
Raise the table by turning the crank handle
clockwise until the indicator plate points
to the scale graduation indicating the desired finished dimension. One full turn of
the crank handle moves the table 2 mm
(3/32") up or down. The scale has inch
graduations on i t s right side and metric
graduations on i t s left side.
Adjusting the depth of cut
The maximum depth of cut differs depending upon the width of workpiece being cut.
Refer to the table a t right. When you wish
to cut deeper than the amount specified in
the table, make two or more passes to
avoid overloading the motor, jamming the
workpiece and subsequent damage.
To adjust the depth of cut, proceed as
follows.
Insert the workpiece flat on the infeed
table top. Raise the table by turning the
crank handle clockwise. The depth gauge
will rise and the amount of gauge rise indicates the depth of cut.
I
Scael-\
I
Crank h
Indicator plate
a
n
d
l
e
M a x demh of
d
cut
3 mm
( 1 18")
s
d
1 "
(1132"l
nm
150"
16 I
132"l
Width
Scale 7
&
\
'
Indicator plate
CAUTION :
Always raise the table when aligning the indicator plate with the graduation indicating
the desired finished dimension. If the table i s lowered into the desired finished dimension, additional play in the screw may result. This may cause an undesired finished
dimension, gouging or sniping of the workpiece.
*Always place the workpiece flat on the infeed table top when predetermining the depth
of cut. Otherwise, the predetermined depth of cut will differ from actual depth of cut.
7
Operation
Determine the depth of cut as described
before. Insert the workpiece flat on the
table top. When cutting a long or heavy
workpiece, lift up i t s end slightly at the
start and the end of the cut to avoid gouging or sniping a t the extreme ends of the
work piece.
Two rollers are provided on top of the tool
t o enable quick, effotless return of the
workpiece to the infeed table side. This i s
especially convenient with two operators.
Roller
CAUTION :
e Workpieces
with the following dimensions cannot be fed into the auto-planer because
the interval between the two feed rollers i s 114 mm (4-1/2"). Do not try to cut them.
I
1
1I
7-
1
I
Fq
Less than 1 1 5 m m
More than 1 1 5 mm
(4-1i2")
I
I
Less than
I 1 5 mm (4-1
/2")
Having a groove more than
long.
115 mm (4-1/2")
wide.
115mm(4112 I
3
Having grooves at intervals of 1 1 5 mm
(4-1
/2").
estop the tool when the workpiece has stalled. Allowing the tool to run with a stalled
workpiece causes rapid wearing of the feed rollers.
8
JOINTER FUNCTIONS:
Extension support table
The extension support table i s convenient
for cutting long workpieces. Install it on
the outfeed table and semi-tighten the four
hex bolts. Extend the legs and hook the
arms over the screw using the hook (A).
Then tighten the screws securely. Adjust
the table height using the knobs so that the
extension support table i s level with the
outfeed table. Then tighten the wing nuts
securely. After adjusting the table height,
tighten the four hex bolts securely.
I
When moving the tool, fold the extension
support table as follows.
First fold the extension support table as
shown in the figure. Tighten the two hex
bolts securely. While holding the legs,
loosen the screws and unhook the arms
from the screw. Fold the legs and hook the
arms over the screw using the hook (6).
Then tighten the screws securely.
Extension support table
- 1
Hook (A)-,
7
Hex bolts
Arm
Screw
VI
I
x e H ;
bolt
Adjusting the depth of cut
The depth of cut can be adjusted from
0 mm to 3 mm (1/8"). Align the pointer to
the desired graduation on the scale plate by
turning the depth adjusting knob. The infeed table i s lowered for increased depth of
cut by turning i t clockwise and raised by
turning i t counterclockwise.
Scale plate
1 L Depth adjusting knob
9
Adjusting the fence angle
The fence angle can be adjusted a t any
angle from 0’ to 45’. Loosen the clamp
screws ( A ) and (B) and pull the fence out
slightly. Then tighten the clamp screws (A)
and (B). Loosen the hex bolts ( A ) and (B)
and tilt the fence according to your work.
Then tighten the hex bolts ( A ) and (B)
securely.
I
ClamD screw ( A )
7
Hex bolts ( A )
-Fence
bolts (6)
Operation
Placement of hands during feeding
At the start of the cut, the left hand holds the workpiece firmly down on the infeed table
and firmly against the fence. The right hand pushes the workpiece toward the blades.
After the cut has started, the new surface rests firmly on the outfeed table. The left hand
should press down on this part well away from directly over the cutterhead, a t the same
time maintaining flush contact with the fence. The right hand presses the workpiece
forward and before the right hand passes over the cutterhead it should be cautiously
moved to the workpiece on the outfeed table.
Jointing an edge
Set the fence square with the table. Hold
the best fece of the workpiece firmly
against the fence throughout the feed. Side
pressure i s required to keep the workpiece
in flush contact with the fence. This i s very
important when jointing wide workpiece.
Surfacing
For surfacing, press the workpiece down
against the outfeed table. Surfacing or
planing a wide work surface on a warped or
twisted board is very difficult t o accomplish. Hold-down/push blocks be useful in
all cases. They should always be used when
surfacing workpieces thinner than 76.2 mm
(3”).If the workpiece is warped m , joint
the dished (hollow, concave) surface first,
whenever possible. Small depths of cut
only should be taken whenever surfacing
warped workpieces.
10
Fence
L
1
-
Joint
I
Joint edge of workpiece on
dished side whenever possible
Beveling
To cut a bevel, set the fence a t the required angle and run the workpiece across the blades
while keeping it firmly against the fence and tables. Carefully maintain flush, steady contact with the fence while making the cut.
REPLACING THE PLANER BLADES
Dull blades can cause a rough finish, an overload of the motor and dangerous kickback of
the workpiece. Sharpen or replace dull blades immediately. This tool is equipped with
either throw-away blades or standard blades. The method of replacing the blades differs
depending upon the type of the blade. Follow the correct method for your tool.
CAUTION :
*Always be sure that the tool is switched off and unplugged before removing or installing
the blades.
0
0
0
Handle the blades very carefully when removing or installing the blades to prevent cuts
or injury from the blades and to prevent damage to the blades. They are razor-sharp.
Clean out all chips, dust, pitch or foreign matter adhering to the drum or blades before
installing the blades.
Use blades of the same dimensions and weight, or drum oscillation/vibration will result,
causing poor cutting action and, eventually, tool breakdown.
Replace both blades a t the same time.
.The throw-away blade has a cutting edge on both sides. When one cutting edge becomes
dull, you can use the other cutting edge. Always remove resin and dirt sticking to the
reverse side of the blade before using the other cutting edge. This blade must not be resharpened. When both cutting edges become dull, the blade should be carefully thrown
away.
11
AUTO-PLANE R
1. Removing the blades
Loosen the hex bolt which secures the
chip cover and open the chip cover.
Open the safety cover over the jointer
and rotate the drum by turning the
knob until the drum can be locked in
the position whereby the blade installation bolts face upward.
Knob
1
Hex bolt
Blad; installation bolt
The magnetic holder has a different
shaped claw on each side. Use the correct claw for auto-planer.
For jointer
Claw
M
I
Magnetic holder
Place the two magnetic holders on the set plate and push them in the direction of the
arrow until the claw contacts the blade. Remove the eight blade installation bolts using
the socket wrench. Grip the magnetic holders and raise them straight up to remove the
set plate and blade from the drum. Press the lock plate and rotate the drum by turning
the knob 180" to lock the drum. Remove the other blade as described above.
-
Socket wrench
I Blade installation bolt
LMagnetic holders
12
2. Installing the blades
Provide a flat wood block approx.
300 mm (11-13/16") long and 100 mm
(3-15/16") wide. Place the blade and set
plate on the wood block so that the
blade locating lug of the set plate rests
in the groove of the blade. Adjust the
s e t plate so that both ends of the blade
protrude approx. 1 mm (3/64") beyond
the end of the set plate. Place the two
magnetic holders on the set plate and
push them until the claw contacts the
blade (Note: Use the correct claw for
auto-planer.
Magnetic holder
I
Set plate
(3/64")
Grip the magnetic holders and slip the
heel of the set plate into the groove in
the drum. Install the blade installation
bolts.
~
After tightening all the blade installation bolts lightly and evenly from the
center to the outside, tighten them completely following the same sequence.
Remove the magnetic holders from the
set plate.
Blade
Blade installation bolt
Magnetic holder
-Socket
wrench
Magnetic holders
13
Install the other blade as described above. Rotate the drum slowly while pressing the lock
plate to make sure there i s nothing abnormal. Then close the chip cover and secure using
the hex bolt.
CAUTION :
Do not tighten the blade installation bolts without the blade locating lug of the set plate
correctly resting in the groove of the blade. This may cause damage to the blade and
potential injury to the operator.
0
0
Tighten the blade installation bolts securely when installing the blades.
Do not turn the tool on with the chip cover open.
14
JOINTER
1. Removing the blades
CAUTION :
Always close the chip cover over the auto-planer before removing the blade.
Lower the infeed table fully by turning
the depth adjusting knob clockwise.
Loosen the hex bolt which secures the
safety cover rod and lift off the safety
cover. Set the fence angle a t 0
' and
push the fence fully toward the autoplaner. Pull the lock pin and rotate the
drum by turning the knob to lock the
drum in the position whereby the blade
installation bolts face upward.
Lock pin
-
(NOTE)
The drum can be locked in two different positions. One position is where the blade
edge faces upward and the other i s where the blade installation bolts face upward.
Remove the four blade installation bolts
and the drum plate. Place the two magnetic holders on the set plate. (Note:
The magnetic holder has a different
shaped claw on each side. Use the correct claw for jointer.) Push them in the
direction of the arrow until the claw
contact the blade.
Grip the magnetic holders and raise
them to remove the set plate and blade
from the drum. Pull the lock pin and
r o t a t e the drum by turning the knob
180' to lock the drum. Remove the
other blade as described above.
15
2. Installing the blades
Provide a flat wood block approx.
150 mm (5-29/32") long and 100 mm
(3-15/16") wide. Place the blade and s e t
plate on the wood block so that the
blade locating lug of the set plate rests
in the groove of the blade. Adjust the
set plate so that both ends of the blade
do not protrude from the ends of the
s e t plate. Place the two magnetic holders
on the set plate and push them until the
claw contacts the blade. (Note: Use the
correct claw for jointer.)
Lock the drum in the position whereby
the blade installation bolts face upward.
Place the set plate and blade on the
drum so that the heads of the depth
adjusting screws in the drum f i t into the
square holes in the set plate. Remove
the magnetic holders while holding the
set plate with your hand.
Place the drum plate on the set plate.
Install the blade installation bolts and
semi-tighen them.
16
Lock the drum in the position whereby
the blade edge faces upward. Place the
triangular rule flat on the outfeed table.
Turn the adjusting screws until the
blade edge just contacts the triangular
rule. After adjusting both adjusting
screws, pull the lock pin to unlock the
drum. Rotate the drum by turning the
knob clockwise to make sure the blade
protrusion is a t exactly the same height
a l l the way across. If not, adjust the
adjusting screws again.
Outfeed t a b l e
After carefully adjusting the blade protrusion, lock the drum in the position
whereby the blade installation bolts
face upward. Securely tighten the blade
installation bolts evenly from the center
of the outside.
Then slightly retighten the adjusting
screws by turning clockwise.
I
17
Install the other blade as described above. Re-install the safety cover in i t s original
position and be sure that the safety cover works properly and briskly.
CAUTION :
Do not tighten the blade installation bolts without the blade locating lug of the set
plate correctly resting in the groove of the blade. This may cause damage to the blade
and potential injury to the operator.
Tighten the blade installation bolts securely when installing the blades.
Always be sure that the drum is unlocked after installing the blades.
18
REMOVING OR INSTALLING THE JOINTER
CAUTION :
Always be sure that the tool is switched off and unplugged before removing or installing
the jointer.
The jointer can be easily removed from the auto-planer. You can carry it by yourself.
1. Removing the jointer
Loosen the right and left knobs. Pull the
jointer toward you as shown in the
figure. The jointer can be removed.
-
Knob
When the jointer is removed, the pulley
cover will close automatically. If you
lock the pulley cover in the open position for some reason, be sure to close it
by pushing the release button before
operating the auto-planer. Never operate
the auto-planer with the pulley cover
locked in the open position.
2. Installing the jointer
Open the pulley cover until it will be
locked. Align the line on the pulley with
the pointer on the side cover (L).
I
Side cover ( L )
Pulley cover
/--
,-Pointer
/=I
\L'
-
\\\
...
'
Line
Pulley
19
Loosen the clamp screws which secure
the fence. Remove the fence. Align the
line on the coupling with the pointer on
the frame of the jointer.
I
s
Coup1ing
Line
e
o
i
n te r
Align the two shafts of the jointer with the mating holes in the auto-planer. Push the
jointer toward the auto-planer until the frame of the jointer contacts that of the autoplaner. Make sure the jointer i s correctly installed on the auto-planer by viewing the
contact portion through the notch. Tighten the knobs to secure the jointer. Re-install
the fence and tighten the clamp screws to secure the fence.
r ‘lamp
Screw
Mating
Knob
Knob
20
-/
See this contact portion 2
through notch.
-Shaft
of jointer
MAINTENANCE
CAUTION :
Always be sure that the tool i s switched off and unplugged before attempting to perform
inspection or maintenance.
Replacing carbon brushes
Remove and check the carbon brushes regularly. Replace when they wear down to
the limit mark. Keep the carbon brushes
clean and free to slip in the holders. Both
carbon brushes should be replaced a t the
same time. Use only indentical carbon
brushes.
c
1
L
Limit mark
Open the chip cover and remove the brush
holder caps using a screwdriver. Take out
the worn carbon brushes, insert the new
ones and secure the brush holder caps.
Brush holder cap
I
\
Screwdriver
Lubrication
Oil the chain (after removing the side cover
R), the column moving parts (contact areas)
and the crank handle. This periodic lubrication should be performed with machine oil.
CAUTION :
Oiling and all maintenance should be done
with the tool turned off and unplugged.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance and
adjustment should be performed by Makita Authorized or Factory Service Centers,
always using Makita replacement parts only.
21
ACCESSOR I ES
ATTENTION :
These accessories or attachments are recommended for use with your Makita tool specified in this
manual. The use of any other accessories or attachments might present a risk of injury to persons. The
accessories or attachments should be used only in the proper and intended manner.
0
Planer blade
0
Magnetic holder
Part No. 76201 7-8
0
Key
Part No.
Socket wrench 9
Part No. 782203-5
0
Screwdriver
Part No. 783002-8
0
Triangular rule
Part No. 762001-3
0
Y joint assembly
Part No. 122342-3
c
0
IO' set
(For auto-planer)
Part No. 192382-5
0
Hood set
(For jointer)
Part No. 192383-3
Extension support table
Part No. 192381-7
0
Push block
Part No. 155508-0
22
Mar-22-’94
US
312 m m (12-9/32”)
PLANER-JOINTER
Model 2030s
23
24
Note: The switch and other part configurations
may differ from country to country.
25
Mar.-22-'94
MODEL 2 0 3 0 s
'v0M
MA(
1
2
3
4
5
6
1
$&
9
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
41
48
49
50
51
52
53
54
55
56
51
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
13
26
DESCRIPTION
DESCRIPTION
MACHlNE
INE
~
2
2
2
2
2
2
2
8
10
11
12
13
14
16
17
18
19
20
21
22
23
24
25
26
27
$&
1
2
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
2
2
2
1
1
1
1
1
1
1
Compression Soring 14
Roller Shaft
Roller 29-300
Compression Spring 1 4
Stop Ring E - 6
Pan Head Screw M5x16 (With Washer!
Stop Ring E - 6
Pan Head Screw M5x60 (With Wanherl
Chip Cover
Countersunk Head Screw M4x30
Tube 1 0 - 1 0 8 - 1 5
Strain Relief
lapping Screw 4x18
Switch Box
Switch
Tapping Screw Bind PT3x8
Tapping Screw Flange P T 4 x l 2
Swttch Supporter
Strain Relief
Tapping Screw Flange PT4x12
Tapping Screw Flange PT4x12
Strain Relief
Switch Box Cover
Name Plate
G ~ W
nouslng
Makita Label
Flat Washer 12
Helical Gear 45
Woodruff Key 4
Drive Shaft
Flat Washer 1 4
ear tiouslng C O W
Pan Head Screw M5x85 IWifh Washer)
Torsion Spring 2 3
Te"SlOn.3,
Sprocket 1 2
Retaining Ring S - 12
Pan Head Screw M5x20 (With Washer)
Tension Roller
Plane 8earl"g 5
Ring 6
Pan Head Screw M5x25 [With Washer!
Flat Washer 8
Gear Complete 8 - 4 4
Gear Complete 8 - 4 7
Flat Washer 8
Flat Washer 6
flat Washer 6
field
Poly V Belt 9 314
Carbon Brush
Brush Holder Cap
Pan Head Screw M5x25 [With Washer)
Motor Housing
Pan Head Screw M5x8O IWith Washer!
Pan Head Screw M5x80 [With Washer!
Baffle Plate
V Pulley 9-25L
Ball Bearing 6200DDW
lnwlation Washer
Armature
Ball Bearing 6200DDW
Main Drum
Ball Bearing 6202LLB
Ball Bearing 6202LLB
Hex Flange Head Bolt M5x10
Knob 4 0
Bearing Box
Countersunk Head Screw M5x16
Lock Plate
Torsion Spring 12
Pan Head Screw M5x25 (With Washer!
74
75
76
11
78
79
80
81
82
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
1 110
111
112
113
114
115
116
111
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
131
138
139
140
141
142
143
144
145
146
1
1
1
1
1
1
1
16
2
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
1
1
1
1
2
1
2
1
1
1
1
8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
v
1
Pulley 9 - 5 8
Hex Socket Head Bolt M6x12
Key 4
Flat Washer 6
Sleeve 5
Gauge
Main Frame
Hex Flange Head Bolt M6x17
Set Plate 3 1 0
Chain 3 5 - 5 0
Retaining Ring 5- 12
Sprocket 12
Metal Cover 18)
Plane Bearing 17
Compression Spring 7
CDmPleSSlOn s p m g 13
Hex Socket Head Bolt M5x16 [With Washer!
Retaining Ring S - 12
Sprocket 12
Metal Cover IB!
Hex Socket Head Bolt M5x16 IWJth Washer!
Plane Bearing 17
Compression Spring 13
Roller 3 4 - 2 9 5
Knob 40
Compression Spring 13
Plane Bearing 17
Metal Cover IAI
Hex Socket Head Bolt M5x16 IWith Washerl
Metal Cover I A l
Hex Socket Head Bolt M5x16 lWith Washer!
Compression Spring 13
Plane Bearing 1 1
Roller 34-295
Table Plate
Countersunk Head Screw M4x12
Hex Lock Nut M E - 1 3
Flat Washer 8
Table
Pan Head Screw M5x8 IWith Washer!
Indicator
set Plate
Pan Head Screw M5x8 [With Washer]
Woodruff Key 3
Screw M 1 6
Thrust Needle Bearing 1023
Straight Bevel Gear 16
Flat Washer 10
Compression Spring 15
Stop Ring E - 12
Handle Shaft
Retaining Ring S - 1 0
Straight Bevel Gear 16
S p m g P," 4 - 18
Pan Head Screw M5x16 IWith Washerl
Stop Ring E - 6
Flat Washer 8
Knob 45
P,"8
Handle Supporter
Handle 125
Hex Flange Head Bolt M5x10
Pan Head Screw M5x30 IWtth Washer!
Side Cover L
Pan Head Screw M5x30 IWith Washer!
Side Cover R Complete
Foot
Leg
Cord
Strain Relief
Pan Head Screw M4x12 IWith Washer!
Hex Flange Head Bolt M6x17
US
MODEL 20305
Mar-22-'94
y' 0M sD
DESCRIPTION
1
1
1
1
1
4
1
4
1
1
1
1
1
1
2
1
1
20
1
1
1
1
2
1
1
1
1
2
1
1
1
2
1
1
2
1
1
NO
USED
US
DESCRIPTION
MACHINE
_
_
MACHINE
_
_
147
148
149
150
151
152
153
154
155
158
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
ITEM
NO.
Hex Flange Head Bolt M6x17
Leg
Foot
Base Cover
Pan Head Screw M5x16 IWith Washer)
Spring Pin 6 3 6
Base
Cap 2 0
Drum cover
Retaining Ring S 12
SpringPin4-16
Spring Pin 4 - 3 2
Rod 1 2 - 9 5
Torsion Spring 14
Bedplate
Adlust Bed
Indication Label
Countersunk Head Screw M 4 x l 2
Knob 4 0
Spring Pin 4 - 18
SpringPin4-18
Flat Washer 10
Pan Head Screw M5x16 IWith Washerl
Screw Holder
Flat Washer 10
Hex Flange Head Bolt M6x17
Hex Flange Head Bolt M6x17
Pan Head Screw M5x16 (With Washerl
Rule Holder L
Ruler Bar
Safety Cover
Pan Head Screw M5x16 (With Washerl
Ruler Bar
Rule Holder R
Pan Head Screw M5x16 IWith Washerl
Hex Flange Head Bolt M6x17
Hex Flange Head 8011 M6x17
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
217
218
219
220
1
1
1
4
1
1
1
1
1
1
2
1
2
1
1
1
1
1
1
I
2
1
2
1
2
2
2
1
1
1
4
1
2
2
8
1
Ruler
Set Screw M5x8
Lock Sleeve
Pan Head Screw M5x16 (With Washerl
Bearing Cover
Nut M 4 12
stopper Pln
Pln 2
compression sprmg 5
Hex Flange Head Bolt M5x10
Pan Head Screw M5x8 (With Washerl
Scale Plate
Screw M6x19
Fix Bed
Rod 17 6 3
Coupling Cushion
Hex Socket Head Bolt M6x12
Coupling
Set Screw M5x12
Key 4
Cup Washer 8
Rod 1 7 - 9 0
Flat Washer 8
Set Screw M5x12
Compression Spring 9
Hex Socket Head Bolt Max50
Pan Head Screw M5x16 (With Washer)
Chip Guide
Pan Head Screw M5x16 lWith Washer]
Sub Drum
Flat Head Screw M5x13
Ball Bearing 6200DDW
set Plate 155
Drum Plate
Hex Flange Head Bolt M6x17
Ball Bearing 6201DDW
21
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Poiicy
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to
be free of defects from workmanship and materials for the period of ONE YEAR from the date of
original purchase. Should any trouble develop during this one-year period, return the COMPLETE
tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows
the trouble is caused by defective workmanship or material, Makita will repair (or at our option,
replace) without charge.
This Warranty does not apply where:
repairs have been made or attempted by others:
repairs are required because of normal wear and tear:
The tool has been abused, misused or improperly maintained;
alterations have been made to the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THlS DlSCLAIMER
APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED
WARRANTIES OF “MERCHANTABILITY” AND “FITNESS FOR A SPECIFIC PURPOSE,”
AFTER THE ONE-YEAR TERM O F THIS WARRANTY.
This Warranty gives you specific legal rights, and you may also have other rights which vary from
state to state. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. Some states do not allow
limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi 446 Japan
883863-069
PRINTED IN JAPAN
1996 - 9 - N