ZMODO CM-S10055BK Mini Hidden Pinhole Camera User's Guide

Mini Hidden Pinhole Camera

User’s Guide

CM-S10055BK

1201-1205 ,Sangda Mansion, High Technology Park,

ShenZhen, Guangdong, China

Tel: 0755-3363-1636 Fax: 0755-3363-1639

SAFETY PRECAUTIONS

WARNING CAUTION

1. Be sure to use only the standard adapter that is

specified in the specification sheet. Using any

other adapter could cause fire, electrical shock, or

damage to the product

2. Incorrectly connecting the power supply or

replacing battery may cause explosion, fire,

electric shock, or damage to the product.

3. Do not connect multiple cameras to a single

adapter. Exceeding the capacity may cause

abnormal heat generation or fire.

4. Securely plug the power cord into the power

receptacle. Insecure connection may cause fire.

5. When installing the camera, fasten it securely and

firmly. A falling camera may cause personal injury

6. Do not place conductive objects (e.g.screwdrivers,

coins, metal things, etc.) or containers filled with

water on top of the camera. Doing so may cause

personal injury due to fire, electric shock, or falling

objects.

7. Do not install the unit in humid, dusty, or sooty

locations. Doing so may cause fire or electric

shock.

8. If any unusual smells or smoke come from the unit,

stop using the product. In such case, immediately

disconnect the power source and contact the

service center. Continued use in such a condition

may cause fire or electric shock.

9. If this product fails to operate normally, contact the

nearest service center. Never attempt to modify

this product in any way. (ZMODO is not liable for

problems caused by unauthorized modifications or

attempted repair.)

10. When cleaning, do not spray water directly onto

parts of the product. Doing so may cause fire or

electric shock.

1. Do not drop objects on the product or apply strong

shock to it. Keep away from a location subject to

excessive vibration or magnetic interference.

2. Do not install in a location subject to high

temperature (over 120F), low temperature (below

-5F), or high humidity. Doing so may cause fire or

electric shock.

3. If you want to relocate the already installed

product, be sure to turn off the power and then

move or reinstall it.

4. Remove the power plug from the outlet when then

there is a lightning. Neglecting to do so may cause

fire or damage to the product.

5. Keep out of direct sunlight and heat radiation

sources. It may cause fire.

6. Install it in a place with good ventilation.

7. Avoid aiming the camera directly towards

extremely bright objects such as sun, as this may

damage the CCD image sensor.

8. Apparatus shall not be exposed to dripping or

splashing and no objects filled with liquids, such as

vases, shall be placed on the apparatus.

9. The Mains plug is used as a disconnect device and

shall stay readily operable at any time.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE REAR COVER.

NO USER SERVICEABLE PARTS

INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

This symbol alerts you that important literature concerning operation and maintenance has been included with this product.

This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product.

1

1201-1205 ,Sangda Mansion, High Technology Park,

ShenZhen, Guangdong, China

Tel: 0755-3363-1636 Fax: 0755-3363-1639

PRODUCT OVERVIEW

Product Overview

Discretely monitor your home or small business with this hidden camera. Featuring a clever styling as an easily overlooked common item, this camera includes imaging provided by a 1/3"

Sony Color CCD, which delivers good video quality, reliable operation, a long operating life, and high value. This hidden camera is designed for indoor use, and can easily be mounted for the perfect viewing angle. BNC and RCA connections are used for video and power. Installation is easy and hassle free, just plug and play.

Package includes

Please check your camera and accessories included in the package. Those components are as shown below:

Camera

Main Features

1/3" Sony Color CCD Image Sensor

420 TV Lines, Horizontal

3.7mm Pinhole Lens

Signal: NTSC

Iris: Auto

Night Vision Min. Light: 0.5 Lux (F1.2)

Operation Temperature: -5F ~ 120F

Mount: Wall or Ceiling

Video Connector: BNC

Power Connector: RCA 12V DC

Screws

Mount Bracket

CCD CAMERA

CCD CAM

ERA

WWW.Z

MODO

.COM

C

C

D

C

AM

ER

A

W

W

W

.Z

M

OD

O.

CO

M

Package Box

1) CM-S10055BK Mini Hidden Pinhole Camera

1) A Card

3) Screws

1) Package Box

2

1201-1205 ,Sangda Mansion, High Technology Park,

ShenZhen, Guangdong, China

Tel: 0755-3363-1636 Fax: 0755-3363-1639

SCHEMATIC DIAGRAM

1 Main Body

2 Pinhole Lens

3 Mount Bracket

1201-1205 ,Sangda Mansion, High Technology Park,

ShenZhen, Guangdong, China

Tel: 0755-3363-1636 Fax: 0755-3363-1639

3

CONNECTING CABLES

RCA Cable

DVR

Video Balun

Monitor

BNC Cable

To connect cables

1.

Connect the BNC cable to the video connector attached on your camera

2.

Connect the BNC cable to the Video Input on a monitor, DVR or Video Balun.

3. Connect the power adapter to the RCA Power connector attached on your camera. When the

monitor is turned on, the camera image appears.

Note

It is very important that you identify these ends before installing the cable so that you have the correct ends at the correct location.

4

1201-1205 ,Sangda Mansion, High Technology Park,

ShenZhen, Guangdong, China

Tel: 0755-3363-1636 Fax: 0755-3363-1639

HOW TO INSTALL

Before installation

Please read the following instructions before installing your camera:

You have to check whether the location (ceiling or wall) can bear five times the weight of your

camera.

Do not allow the cable to be caught in a pinched area, otherwise the electric line cover may be

damaged. This may cause cable breakdown or fire.

When installing your camera, don't allow anyone to walk or stand under your installation site,

and remove all valuable items. A dropped camera may cause injury to bystanders or harm to

valuable items.

Installation procedure

To install your camera step

5

1201-1205 ,Sangda Mansion, High Technology Park,

ShenZhen, Guangdong, China

Tel: 0755-3363-1636 Fax: 0755-3363-1639

HOW TO INSTALL

Pinhole Lens step

Attach the Mount Bracket to the 2 screws supplied in your package. As shown in the picture, push the three screws into the 3 holes on the bottom of the Mount Bracket, then twist in the screws into the wall using a screwdriver.

step on clockwise until it becomes tight.

Note

As shown on the left, you can also put the whole Main Body into the wall or ceiling.

Only left the pinhole lens outside. If mounted in this way, it will be more covert.

step

Bracket. Make sure that the pinhole lens is facing the camera’s monitoring area.

The camera now is installed on the mounting location.

1201-1205 ,Sangda Mansion, High Technology Park,

ShenZhen, Guangdong, China

Tel: 0755-3363-1636 Fax: 0755-3363-1639

6

Screw

CAMERA SPECIFICATION

Specifications for NTSC & PAL Standard

Item

Product type

Power input

Broadcast type

Power Consumption

Image device

Effective Pixels

Scanning mode

Synchronization mode

Horizontal resolution

Minimum illumination

Signal output

Lens

S/N Ratio

Controls

Product color

Operation temperature

Size (package)

Weight

Mounting

Details

Mini Pinhole Hidden Camera

NTSC Standard color system

DC 12V

PAL Standard color system

(525 Lines, 60 Fields) (625 Lines, 50 Fields)

Approx. 120mA

1/3 inch SONY Color CCD

510(H) x 492(V), 250,920 pixels

NTSC Standard PAL Standard

525 Lines 625 Lines

Internal Synchronization

Focal Length

420 TV Lines

0.5Lux (F1.2)

1.0Vp-p, 75ohms

Zone

Horizontal

Limit of Viewing Angle

3.7mm pinhole

Vertical

78°

68°

> 48dB

Auto Iris

Auto Gain Control

Auto Back Light Compensation

Auto Switching between Color and B&W by day and night change(D/N)

Black

-5F—120F

2.44"x 1.69"x 1.81”

0.31 lbs

Ceiling or Wall

1201-1205 ,Sangda Mansion, High Technology Park,

ShenZhen, Guangdong, China

Tel: 0755-3363-1636 Fax: 0755-3363-1639

7

FCC Statement

This device complies with part 15of the FCC

Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received including interference that may cause undesired operation.

Note

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 1 5 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Correct Disposal of This Product

(Waste Electrical & Electronic

Equipment) (Applicable in the

European Union and other

European countries with

separate collection systems)

This marking shown on the product or its literature, indicates that it shouldnot be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

SKU: CM-S10055BK

8 4 6 6 5 5 0 0 1 5 6 2

8

1201-1205 ,Sangda Mansion, High Technology Park,

ShenZhen, Guangdong, China

Tel: 0755-3363-1636 Fax: 0755-3363-1639