Alliance Laundry Systems GA2210*A1102 Specifications

Pocket Hardmount
Refer to Page 8 for Model Identification
Installation/Operation/Maintenance
Washer-Extractors
PHM1427C_SVG
Original Instructions
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
www.alliancelaundry.com
F8423301ENR3
August 2014
Table of Contents
Safety Information..................................................................................5
Explanation of Safety Messages....................................................................... 5
Important Safety Instructions........................................................................... 5
Safety Decals................................................................................................. 6
Operator Safety.............................................................................................. 6
Introduction........................................................................................... 8
Model Identification........................................................................................8
Delivery Inspection.........................................................................................8
Serial Plate Location....................................................................................... 8
Serial Plate Information - UniLinc Models.................................................... 8
Replacement Parts ......................................................................................... 8
Customer Service............................................................................................8
Specifications and Dimensions................................................................ 9
Specifications and Dimensions.........................................................................9
Machine Dimensions ....................................................................................13
Machine Foundation Requirements.................................................................17
Concrete Foundation Pad Installation..............................................................17
Floor Load Data........................................................................................ 19
Mounting Bolt Installation Requirements [Approved Foundations Only]............20
Machine Mounting and Grouting................................................................ 21
Grout Placement........................................................................................... 21
Mounting Bolt Hole Locations....................................................................... 23
Gap Setting for Vibration Switch................................................................ 35
Drain Connection Requirements.....................................................................37
Water Connection......................................................................................... 39
Electrical Installation Requirements................................................................41
Electrical Specifications.............................................................................43
Steam Requirements (Steam Heat Option Only)...............................................53
Chemical Injection Supply System................................................................. 54
Connecting External Liquid Supplies.......................................................... 55
Connecting External Liquid Supplies to the Machine with Optional Five Compartment Supply Dispenser..................................................................... 56
External Supplies.......................................................................................... 58
Chemical Injection Using Internal 24VAC Control Transformer.................... 59
Chemical Injection Using External AC Power Source................................... 59
External Supply Signals............................................................................. 60
Startup................................................................................................. 62
Basket Rotation............................................................................................ 62
© Copyright
2014, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed
written consent of the publisher.
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
3
Operation............................................................................................. 63
Operating Instructions for UniLinc Control..................................................... 63
Shakeout Routine...................................................................................... 64
Basket Jog Feature [150 Pound Model Only]............................................... 64
Operating Instructions for M30 Control.......................................................... 65
Shakeout Routine...................................................................................... 67
Models Equipped with Both Steam and Electric Heating.................................. 67
Maintenance......................................................................................... 68
Maintenance.................................................................................................68
Daily........................................................................................................... 68
Beginning of Day...................................................................................... 68
End of Day............................................................................................... 69
Weekly........................................................................................................ 69
Monthly....................................................................................................... 69
Quarterly......................................................................................................70
Care of Stainless Steel................................................................................... 70
Disposal of Unit.................................................................................... 71
Disposal of Unit............................................................................................71
4
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Safety Information
Safety Information
Explanation of Safety Messages
•
Precautionary statements [“DANGER,” “WARNING,” and
“CAUTION”], followed by specific instructions, are found in this
manual and on machine decals. These precautions are intended
for the personal safety of the operator, user, servicer, and those
maintaining the machine.
•
DANGER
•
Indicates an imminently hazardous situation that, if
not avoided, will cause severe personal injury or
death.
WARNING
Indicates a hazardous situation that, if not avoided,
could cause severe personal injury or death.
•
CAUTION
Indicates a hazardous situation that, if not avoided,
may cause minor or moderate personal injury or
property damage.
Additional precautionary statements [“IMPORTANT” and
“NOTE”] are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used to inform the reader of specific procedures where minor
machine damage will occur if the procedure is not followed.
NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related.
To reduce the risk of fire, electric shock, serious injury or death to persons when using your washer,
follow these basic precautions:
W023
F8423301ENR3
•
•
WARNING
Read all instructions before using the washer.
•
•
Important Safety Instructions
•
•
•
Install the washer according the INSTALLATION instructions. Refer to the GROUNDING instructions in the INSTALLATION manual for the proper grounding of the washer. All connections for water, drain, electrical power and
grounding must comply with local codes and be made by licensed personnel when required. It is recommended that the
machine be installed by qualified technicians.
Do not install or store the washer where it will be exposed to
water and/or weather.
To prevent fire and explosion, keep the area around machine
free from flammable and combustible products. Do not add
the following substances or textiles containing traces of the
following substances to the wash water: gasoline, kerosene,
waxes, cooking oils, vegetable oils, machine oils, dry-cleaning solvents, flammable chemicals, thinners, or other flammable or explosive substances. These substances give off vapors
that could ignite, explode or cause the fabric to catch fire by
itself.
Under certain conditions, hydrogen gas may be produced in a
hot water system that has not been used for two weeks or
more. HYDROGEN GAS IS EXPLOSIVE. If the hot water
system has not been used for such a period, before using a
washing machine or combination washer-dryer, turn on all hot
water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. The
gas is flammable, do not smoke or use an open flame during
this time.
To reduce the risk of an electric shock or fire, DO NOT use
an extension cord or an adapter to connect the washer to the
electrical power source.
Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used
near children. This appliance is not intended for use by young
children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with
the appliance. This is a safety rule for all appliances.
DO NOT reach and/or climb into the tub or onto the washer,
ESPECIALLY if the wash drum is moving. This is an imminently hazardous situation that, if not avoided, will cause severe personal injury or death.
Never operate the washer with any guards, panels and/or parts
removed or broken. DO NOT bypass any safety devices or
tamper with the controls.
Use washer only for its intended purpose, washing textiles.
Never wash machine parts or automotive parts in the machine. This could result in serious damage to the basket or
tub.
Use only low-sudsing, no-foaming types of commercial detergent. Be aware that hazardous chemicals may be present.
Wear hand and eye protection when adding detergents and
chemicals. Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Heed all
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
5
Safety Information
warnings or precautions. To reduce the risk of poisoning or
chemical burns, keep them out of the reach of children at all
times [preferably in a locked cabinet].
Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener
or product.
Always follow the fabric care instructions supplied by the textile manufacturer.
Loading door MUST BE CLOSED any time the washer is to
fill, tumble or spin. DO NOT bypass the loading door switch
by permitting the washer to operate with the loading door
open. Do not attempt to open the door until the washer has
drained and all moving parts have stopped.
Be aware that hot water is used to flush the supply dispenser.
Avoid opening the dispenser lid while the machine is running.
Do not attach anything to the supply dispenser’s nozzles, if
applicable. The air gap must be maintained.
Do not operate the machine without the water reuse plug or
water reuse system in place, if applicable.
Be sure water connections have a shut-off valve and that fill
hose connections are tight. CLOSE the shut-off valves at the
end of each wash day.
Keep washer in good condition. Bumping or dropping the
washer can damage safety features. If this occurs, have washer checked by a qualified service person.
DANGER: Before inspecting or servicing machine, power
supply must be turned OFF. The servicer needs to wait for at
least 5 minutes after turning the power OFF and needs to
check for residual voltage with a voltage meter. The inverter
capacitor or EMC filter remains charged with high voltage for
some time after powering OFF. This is an imminently hazardous situation that, if not avoided, will cause severe personal
injury or death.
Do not repair or replace any part of the washer, or attempt any
servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions
that the user understands and has the skills to carry out. ALWAYS disconnect the washer from electrical, power and water supplies before attempting any service.
Disconnect the power by turning off the circuit breaker or by
unplugging the machine. Replace worn power cords.
Before the washer is removed from service or discarded, remove the door to the washing compartment.
Failure to install, maintain, and/or operate this washer according to the manufacturer’s instructions may result in conditions
which can produce bodily injury and/or property damage.
•
•
•
•
•
•
•
•
•
•
•
•
•
WARNING
Machine installations must comply with minimum
specifications and requirements stated in the applicable Installation Manual, any applicable municipal
building codes, water supply requirements, electrical wiring regulations and any other relevant statutory regulations. Due to varied requirements and applicable local codes, this machine must be installed,
adjusted, and serviced by qualified maintenance personnel familiar with applicable local codes and the
construction and operation of this type of machinery. They must also be familiar with the potential
hazards involved. Failure to observe this warning
may result in personal injury, property damage,
and/or equipment damage, and will void the warranty.
W820
IMPORTANT: Ensure that the machine is installed on a
level floor of sufficient strength. Ensure that the recommended clearances for inspection and maintenance are
provided. Never allow the inspection and maintenance
space to be blocked.
WARNING
Never touch internal or external steam pipes, connections, or components. These surfaces can be extremely hot and will cause severe burns. The steam
must be turned off and the pipe, connections, and
components allowed to cool before the pipe can be
touched.
SW014
Safety Decals
Safety decals appear at crucial locations on the machine. Failure
to maintain legible safety decals could result in injury to the operator or service technician.
Use manufacturer-authorized spare parts to avoid safety hazards.
Operator Safety
NOTE: The WARNINGS and IMPORTANT SAFETY INSTRUCTIONS appearing in this manual are not meant
to cover all possible conditions and situations that may
occur. Common sense, caution and care must be exercised when installing, maintaining, or operating the
washer.
Any problems or conditions not understood should be reported to
the dealer, distributor, service agent or the manufacturer.
6
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Safety Information
WARNING
NEVER insert hands or objects into basket until it
has completely stopped. Doing so could result in serious injury.
SW012
The following maintenance checks must be performed daily:
1. Verify that all warning labels are present and legible, replace
as necessary.
2. Check door interlock before starting operation of the machine:
a. Attempt to start the machine with the door open. The machine should not start.
b. Close the door without locking it and start the machine.
The machine should not start.
c. Attempt to open the door while a cycle is in progress. The
door should not open.
If the door lock and interlock are not functioning properly, disconnect power and call a service technician.
3. Do not attempt to operate the machine if any of the following
conditions are present:
a. The door does not remain securely locked during the entire cycle.
b. Excessively high water level is evident.
c. Machine is not connected to a properly grounded circuit.
Do not bypass any safety devices in the machine.
WARNING
Operating the machine with severe out-of-balance
loads could result in personal injury and serious
equipment damage.
W728
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
7
Introduction
Introduction
Model Identification
1.
Information in this manual is applicable to these models:
Models
UWL035K12
UWU060K1L
UWL125K1M
UWN035K12
UWL060T3L
UWN080T3V
UWU035K12
UWL060K1M
UWU080T3V
UWL035K1L
UWN060K1M
UWL100K1M
UWN035K1L
UWU060K1M
UWN100K1M
UWU035K1L
UWN060T3L
UWU100K1M
UWL035K1M
UWU060T3L
UWL100T3V
UWN035K1M
UWL060T3M
UWN100T3V
UWU035K1M
UWN060T3M
UWU100T3V
UWL035T3V
UWU060T3M
UWN125K1M
UWN035T3V
UWL060T3V
UWU125K1M
UWU035T3V
UWN060T3V
UWL125T3V
UWL060K12
UWU060T3V
UWN125T3V
UWN060K12
UWL080K1M
UWU125T3V
UWU060K12
UWN080K1M
UWL150T3V
UWL060K1L
UWU080K1M
UWN150T3V
UWN060K1L
UWL080T3V
UWU150T3V
Delivery Inspection
Upon delivery, visually inspect crate, protective cover, and unit
for any visible shipping damage. If signs of possible damage are
evident, have the carrier note the condition on the shipping papers before the shipping receipt is signed, or advise the carrier of
the condition as soon as it is discovered.
Serial Plate Location
The serial plate is located on the valve panel of the machine. Always provide the machine’s serial number and model number
when ordering parts or when seeking technical assistance.
Refer to Figure 1 .
Serial Plate Information - UniLinc Models
Press and hold
same time.
, then
, then
keypads at the
2. Press the
3. Press the
keypad until Diagnostic is highlighted.
4. Press the
5. Press the
keypad until machine ID is highlighted.
keypad.
keypad.
1
2
PHM944N_SVG
Model Example of Serial Plate Location
1. In control (UniLinc Models)
2. At back of machine
Figure 1
Replacement Parts
If literature or replacement parts are required, contact the source
from which the machine was purchased or contact Alliance Laundry Systems at +1 (920) 748-3950 for the name and address of
the nearest authorized parts distributor.
Customer Service
For technical assistance, contact your local distributor or contact:
Alliance Laundry Systems
Shepard Street
P.O. Box 990
Ripon, WI 54971-0990
U.S.A.
www.alliancelaundry.com
Phone: +1 (920) 748-3121 Ripon, Wisconsin
Alliance International: +32 56 41 20 54 Wevelgem, Belgium
On UniLinc models, serial plate information is also programmed
into the control. To access machine ID through the control:
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
8
Specifications and Dimensions
Specifications and Dimensions
Specifications and Dimensions
UW Models
Specifications
35
60
80
100
125
150
Overall Dimensions
Overall width, in. [mm]
33.4 [848]
36.6 [930]
41.5 [1054]
41.5 [1054]
48 [1219]
50.3 [1277]
Overall height, in. [mm]
55.5 [1410]
64.5 [1638]
68.5 [1740]
68.5 [1740]
72 [1829]
79 [2007]
Overall depth, in. [mm]
43.6 [1108]
45 [1143]
51.5 [1308]
54.5 [1384]
58 [1473]
63 [1600]
1030 [468]
[V-speed]
1300 [590]
[V-speed]
1730 [785]
1770 [805]
2420 [1100]
2970 [1347]
750 [341] [2speed]
1136 [515]
[2-speed]
150 [68] [Vspeed]
200 [92]
330 [150]
360 [163]
550 [250]
572 [260]*
1085 [493]
[V-speed]
1340 [608]
[V-speed]
1795 [814]
1835 [832]
2525 [1148]
3022 [1371]
810 [367] [2speed]
1175 [533]
[2-speed]
Domestic shipping volume,
ft3 [m3]
66 [1.9]
84 [2.4]
119 [3.4]
119 [3.4]
166 [4.7]
172 [4.9]
Domestic shipping dimensions, WxDxH, in. [mm]
38 x 47 x 64
[970 x 1200
x 1630]
40 x 49 x
74.5 [1016
x 1245 x
1892]
44 x 60.5 x
77.25 [1118
x 1537 x
1962]
44 x 60.5 x
77.25 [1118
x 1537 x
1962]
61.5 x 60 x
77.75 [1560
x 1520 x
1980]
54.5 x 69
x79 [139 x
176 x 201]
Export shipping weight, lbs.
[kg]
1150 [522]
[V-speed]
1464 [664]
[V-speed]
1990 [903]
2030 [921]
2800 [1270]
3350 [1520]
910 [413] [2speed]
1300 [590]
[2-speed]
Weight And Shipping Information
Net weight, lbs. [kg ]
Basket Weight, lbs. [kg]
74 [34] [2speed]
Domestic shipping weight,
lbs. [kg]
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
9
Specifications and Dimensions
UW Models
Specifications
35
60
80
100
125
150
Export shipping volume, ft3
[m3]
78 [2.2]
96 [2.7]
134 [3.8]
134 [3.80]
184 [5.3]
220 [6.3]
Export shipping dimensions,
WxDxH, in. [mm]
41 x 50 x
65.5 [1050
x 1280 x
1670]
43 x 52.125
x 74.5
[1092 x
1324 x
1892]
47 x 63.5 x
77.25 [1194
x 1613 x
1962]
47 x 63.5 x
77.25 [1194
x 1613 x
1962]
63.5 x 63 x
80 [1620 x
1610 x
2030]
61.5 x 71 x
87 [1562 x
1804 x
2210]
Cylinder diameter, in. [mm]
26.3 [667]
32 [813]
36 [914]
36 [914]
42 [1067]
43 [1093]
Cylinder depth, in. [mm]
18.4 [467]
20 [508]
21 [533]
27 [686]
24 [610]
27.8 [706]
Cylinder volume, ft3 [l]
5.8 [163]
9.3 [264]
12.4 [350]
15.9 [450]
19.2 [544]
23.4 [662]
Perforation size, in. [mm]
0.2 [4.8]
0.2 [4.8]
0.2 [4.8]
0.2 [4.8]
0.2 [4.8]
0.2 [4.8]
Perforation open area, %
18
22
23
23
24
21.5
Door opening size, in. [mm]
14.4 [365]
17.5 [445]
17.5 [445]
17.5 [445]
20 [508]
24.8 [629]
Height of door bottom above
floor, in. [mm]
23.8 [603]
28.3 [718]
29 [737]
29 [737]
29 [737]
32 [813]
Number of motors in drive
train
1
1
1
1
1
1
Drive motor power, hp [kW]
2.0 [1.3] [2speed]
3.0 [2.2] [2speed]
7.5 [5.6]
7.5 [5.6]
10 [7.5]
10 [7.5]
5.0 [3.7] [Vspeed]
5.0 [3.7] [Vspeed]
Wash Cylinder Information
* Basket Only
Door Opening Information
Drive Train Information
Cylinder Speeds / Centrifugal Force Data
10
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
UW Models
Specifications
35
60
80
100
125
150
1/2 Wash/reverse, RPM [G]
[V-speed only]
26 [.25]
26 [.31]
26 [.35]
26 [.35]
26 [.40]
23 [.32]
Wash/reverse, RPM [G]
42 [0.66]
[UniLinc
models]
40 [0.73] [Vspeed]
40 [0.8]
40 [0.8]
37 [0.8]
36 [0.8]
73 [2.57]
[UniLinc
models]
70 [2.5]
62 [2.29]
61 [2.29]
44 [0.73]
[M30 Vspeed models]
44 [0.88] [2speed]
50 [0.95] [2speed]
Distribution, RPM [G] [Vspeed only]
83 [2.57]
71 [2.3]
70 [2.5]
[M30 models]
Very Low extract, RPM [G]
[V-speed only]
401 [60]
364 [60]
343 [60]
343 [60]
317 [60]
314 [60]
Low extract, RPM [G] [Vspeed only]
568 [120]
514 [120]
485 [120]
485 [120]
449 [120]
444 [120]
Medium extract, RPM [G]
[V-speed only]
695 [180]
630 [180]
594 [180]
594 [180]
550 [180]
543 [180]
High extract, RPM [G]
803 [240]
[V-speed]
727 [240]
[V-speed]
686 [240]
686 [240]
565 [190]
627 [240]
504 [95] [2speed]
465 [98] [2speed]
898 [300]
813 [300]
766 [300]
766 [300]
579 [200]
701 [300]
Very High extract, RPM [G]
[V-speed only]
Balance Detection
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
11
Specifications and Dimensions
UW Models
Specifications
Vibration switch installed
35
60
STD [Vspeed]
STD [Vspeed]
N/A [2speed]
N/A [2speed]
80
100
125
150
STD
STD
STD
STD
Direct Steam Heating [Optional]
Steam inlet connection size,
in. [mm]
0.5 [13]
0.5 [13]
0.5 [13]
0.5 [13]
0.75 [19]
0.75 [19]
Number of steam inlets
1
1
1
1
1
1
Steam required to
raise bath
temperature
10°F, lbs.
[10°C, kg]
LOW
2.1 [1.7]
3.3 [2.7]
4.6 [3.7]
5.7 [4.6]
6.7 [5.4]
8.3 [6.7]
MED
2.3 [1.8]
3.7 [3.0]
5.2 [4.2]
6.5 [5.2]
7.8 [6.3]
9.5 [7.6]
HIGH
2.7 [2.2]
4.1 [3.3]
6.1 [4.9]
7.6 [6.1]
9.1 [7.3]
11.1 [8.9]
Total electrical heating capacity, kW [N/A for 2-speed
models]
15.6
27.4
41.2 [QVolt]
41.2 [QVolt]
41.0 [P-Volt]
N/A
27.4 [NVolt]
27.4 [NVolt]
Number of electrical heating
elements
6
6
9
9
12
N/A
Electrical heating element
size, kW
2.6
4.2
4.2
4.2
4.2
N/A
Time required to
raise bath
temperature,
min per
10°F
[5.5°C]
LOW
2.4
2.4
2.2
2.8
N/A
N/A
MED
2.7
2.7
2.5
3.2
N/A
N/A
HIGH
3.1
3.0
3.0
3.7
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Electrical Heating [Optional]
Noise Emission
12
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
54.9 [NVolt]
F8423301ENR3
Specifications and Dimensions
UW Models
Specifications
35
60
80
100
125
150
N/A = Not Applicable
Table 1
Machine Dimensions
ment. Allow at least 6 inches [152 mm] between machines in
multiple installations.
Allow a minimum of 24 inches [610 mm] at the rear and 6 inches
[152 mm] at the sides for maintenance, inspection, and adjust-
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
13
Specifications and Dimensions
1
2
3
6
4
5
F
C
A
G
B
E
D
N
M
9
7
L
10
K
11
14
P
O
8
O
J
13
12
H
PHM858N_SVG
35-125 Pound Models
1. Door Unlock Button
2. Emergency Stop Button
3. Supply Dispenser
4. Door Handle
5. Spray Rinse Nozzle [Optional]
6. Recirculation Inlet
7. Water Inlet Valves
8. Steam Connection [Optional]
9. Shell Vent
10. Power Input [Electric Heat Models]
11. Power Input [Non-Electric Heat Models]
12. Drain [80, 100 and 125 models only]
13. Drain
14. Overflow Vent
Figure 2
14
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
1
8
2
9
10
3
6
4
7
F
J
5
C
A
G
E
D
B
N
M
L
9
10
K
12
O
P
O
11
14
J
H
13
PHM837N_SVG
150 Pound Model
1. Door Unlock Button
2. Emergency Stop Button
3. Supply Valve Box
4. Supply Dispenser
5. Spray Rinse Nozzle
6. Door Handle
7. Basket Jog Buttons
8. Recirculation Inlet
9. Shell Vent
10. Water Inlet Valves
11. Steam Connection [Optional]
12. Power Input
13. Drain
14. Overflow Vent
Figure 3
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
15
Specifications and Dimensions
Machine Dimensions [Refer Figure 2 and Figure 3 ]
35
60
80
100
125
150
A
30.1 in. [765
mm]
35.6 in. [905
mm]
41.1 in. [1045
mm]
41.1 in. [1045
mm]
48 in. [1219
mm]
50.3 in. [1277
mm]
B
33.4 in. [848
mm]
36.6 in. [930
mm]
41.5 in. [1054
mm]
41.5 in. [1054
mm]
48 in. [1219
mm]
50.3 in. [1277
mm]
C
23.8 in. [603
mm]
28.3 in. [718
mm]
29 in. [737
mm]
29 in. [737
mm]
29 in. [737
mm]
32 in. [813
mm]
D
43.6 in. [1108
mm]
45 in. [1143
mm]
51.5 in. [1308
mm]
54.5 in. [1384
mm]
58 in. [1473
mm]
63 in. [1600
mm]
E
3.27 in. [83
mm]
3.8 in. [97
mm]
.36 in. [9 mm]
3.48 in. [88
mm]
2.53 in. [64
mm]
2.9 in. [73
mm]
F
55.5 in. [1410
mm]
64.5 in. [1638
mm]
68.5 in. [1740
mm]
68.5 in. [1740
mm]
72 in. [1829
mm]
79 in. [2007
mm]
G
36 in. [914
mm]
36 in. [914
mm]
43.8 in. [1111
mm]
43.8 in. [1111
mm]
48 in. [1219
mm]
56 in. [1422
mm]
H
8 in. [203 mm]
15.5 in. [394
mm]
16.9 in. [429
mm]
16.9 in. [429
mm]
11.4 in. [289
mm]
15.8 in. [400
mm]
J
47.1 in. [1195
mm]
53.7 in. [1364
mm]
56.4 in. [1433
mm]
56.4 in. [1433
mm]
57.9 in. [1471
mm]
64.4 in. [1635
mm]
K
2.3 in. [58
mm]
2.3 in. [58
mm]
2.3 in. [58
mm]
2.3 in. [58
mm]
2.3 in. [58
mm]
2.3 in. [58
mm]
L
4.9 in. [124
mm]
4.9 in. [124
mm]
4.9 in. [124
mm]
4.9 in. [124
mm]
4.9 in. [124
mm]
4.9 in. [124
mm]
M
7.8 in. [198
mm]
7.8 in. [198
mm]
7.8 in. [198
mm]
7.8 in. [198
mm]
7.8 in. [198
mm]
7.8 in. [198
mm]
N
10.4 in. [264
mm]
10.4 in. [264
mm]
10.4 in. [264
mm]
10.4 in. [264
mm]
10.4 in. [264
mm]
10.4 in. [264
mm]
O
2.6 in. [66
mm]
2.6 in. [66
mm]
2.6 in. [66
mm]
2.6 in. [66
mm]
2.6 in. [66
mm]
2.6 in. [66
mm]
16
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
Machine Dimensions [Refer Figure 2 and Figure 3 ]
35
P
2.9 in. [72
mm]
60
2.9 in. [72
mm]
80
100
2.9 in. [72
mm]
2.9 in. [72
mm]
125
2.9 in. [72
mm]
150
2.9 in. [72
mm]
Table 2
Machine Foundation Requirements
A 6 inch [153 mm] [for 35 and 60 2-speed, L-speed and M-speed
models] or a 12 inch [305 mm] [for all other models] thickness of
4,000 psi reinforced concrete foundation is absolutely necessary
because of the high extract speed and the G-forces exerted.
When designing floors or foundations, refer to Table 4 for Floor
Load Data for all model sizes. If the foundation requirements
have been met, proceed to Mounting Bolt Installation Requirements section.
NOTE: Do not mount on wooden floors, tile floors,
above ground level, or over basements or crawl spaces
because of the high extract speed and the G-forces exerted.
WARNING
To reduce the risk of fire, serious injury, property
damage and/or death, install the machine on a level
(within 3/8 inch), uncovered concrete floor of sufficient strength at grade.
W787
For new foundations a mounting bolt template is available at extra cost. For new foundations a bolt-locator fixture or rebar frame
is also available and a preferred option. This rigid welded assembly made of reinforcing rod and mounting bolts is designed to be
embedded in concrete. Refer to Figure 5 .
The machine must be anchored to a smooth level surface so that
the entire base of the machine is supported and rests on the
mounting surface.
IMPORTANT: Do not permanently support the machine
on only four points with spacers. Grouting is required
and spacers must be removed.
F8423301ENR3
IMPORTANT: The above instructions and recommendations are conservative specifications for a typical installation based on consultations with a structural engineer. Alliance Laundry Systems stands behind all installations meeting these specifications. For alternate
installation specifications based on your soil type, location, building structure, unique floor geometry, machine types, and utilities, consult a structural engineer
in your local area.
Concrete Foundation Pad Installation
A concrete foundation and pad may be constructed to elevate the
machines. This concrete base [recommended not to exceed 8 inches [203 mm] above existing floor] must be placed, reinforced
with rebar and tied to the existing 6 inch [153 mm] [for 35 and 60
2-speed, L-speed and M-speed models] or 12 inch [305 mm] [for
all other models] minimum floor. Refer to Figure 4 and Table 4 .
If the existing floor does not meet these requirements or an elevated pad is desired, the following steps MUST be performed.
IMPORTANT: Do NOT install a pad on top of the existing floor. The foundation and pad must be constructed
and tied together as one piece.
1. Cut a hole larger on all sides than the machine base through
the existing floor. The foundation should extend a minimum
of 9 inches [229 mm] for 35 models or 12 inches [305 mm]
for 60-150 models out from the machine on all sides.
2. Excavate to a depth of 18 inches [457 mm] from the top of the
existing floor.
3. If installing a foundation and elevated pad, prepare a form for
the above-existing floor portion of the foundation. Verify that
the top of the foundation is level. The height of the foundation
pad must not exceed 8 inches [203 mm] above the existing
floor.
4. Backfill and compact fill with gravel or smaller stone, making
sure to allow for correct concrete thickness.
5. Add reinforcing bar to tie existing floor with new floor.
6. Completely fill with a minimum of 6 inch [153 mm] [for 35
and 60 2-speed, L-speed and M-speed models] or 12 inches
[305 mm] [for all other models] with 4,000 psi concrete up to
the existing foundation level. Refer to Figure 4 . The concrete
must be poured so that the entire foundation and optional elevated pad cures as one piece.
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
17
Specifications and Dimensions
NOTE: If the washer-extractor installation will include
the Premium Wet Clean Module, the elevated base
must be designed to accommodate the additional
depth of 24 inches [610 mm].
7. Allow concrete to cure.
8. Proceed to Machine Mounting and Grouting section.
C
E
A
C
G
C
D
C
1
B
F
PHM838N_SVG
1. Compact Fill
Figure 4
35
A
60
2-Speed, L-Speed and M-Speed 6
in. [152 mm]
80
100
125
150
12 in. [305
mm]
12 in. [305
mm]
12 in. [305
mm]
12 in. [305
mm]
V-Speed 12 in. [305 mm]
B [minimum]
6 in. [152 mm]
6 in. [152 mm]
6 in. [152 mm]
6 in. [152 mm]
6 in. [152 mm]
6 in. [152 mm]
C
9 in. [229
mm ]
12 in. [305
mm ]
12 in. [305
mm ]
12 in. [305
mm ]
12 in. [305
mm ]
12 in. [305
mm ]
D
36 in. [914
mm ]
36 in. [914
mm ]
43.75 in.
[1111 mm]
43.75 in.
[1111 mm]
48 in. [1219
mm ]
56 in. [1422
mm ]
E [maximum]
0-8 in. [0-203
mm ]
0-8 in. [0-203
mm ]
0-8 in. [0-203
mm ]
0-8 in. [0-203
mm ]
0-8 in. [0-203
mm ]
0-8 in. [0-203
mm ]
F
48.125 in.
[1222 mm]
59.625 in.
[1514 mm]
65.125 in.
[1654 mm ]
65.125 in.
[1654 mm ]
72 in. [1829
mm]
74.25 in.
[1886 mm]
18
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
35
G
18 in. [457
mm]
60
18 in. [457
mm]
80
100
18 in. [457
mm]
125
18 in. [457
mm]
18 in. [457
mm]
150
18 in. [457
mm]
Table 3
Floor Load Data
Floor Load Data
Specifications
Static floor
load, lbs.
[kN]
Static pressure, lbs.-ft2
[kN-m2]
Dynamic
floor load,
lbs. [kN]
Dynamic
pressure,
lbs.-ft2 [kNm2]
F8423301ENR3
Speed
35
60
80
100
125
150
V-speed
1,272 [5.66]
1,442 [6.42]
2,292 [10.2]
2,490 [11.1]
3,283 [14.6]
3,936 [17.5]
2-speed
1,272 [5.66]
1,442 [6.42]
N/A
N/A
N/A
N/A
L-speed
1,272 [5.7]
1,442 [6.4]
N/A
N/A
N/A
N/A
M-speed
1,272 [5.7]
1,442 [6.4]
2,292 [10.2]
2,490 [11.1]
3,283 [14.6]
N/A
V-speed
169 [8.08]
162 [7.7]
184 [8.79]
199 [9.6]
205 [9.8]
202 [9.7]
2-speed
169 [8.08]
162 [7.7]
N/A
N/A
N/A
N/A
L-speed
169 [8]
162 [7.7]
N/A
N/A
N/A
N/A
M-speed
169 [8]
162 [7.7]
184 [8.8]
199 [9.5]
205 [9.8]
N/A
V-speed
1,576 [7]
2,704 [12]
3,603
[16.36]
4,504
[16.41]
3,746
[22.29]
4,501 [19.4]
2-speed
473 [2.1]
950 [4.23]
N/A
N/A
N/A
N/A
L-speed
525 [2.3]
900 [4]
N/A
N/A
N/A
N/A
M-speed
944 [4.2]
1,624 [7.2]
2,167 [9.6 ]
2,708 [12]
3,380 [15]
N/A
V-speed
380 [18.2]
466 [22.34]
472 [22.63]
559 [26.8]
439 [21]
433 [20.8]
2-speed
233 [11.2]
269 [6.3]
N/A
N/A
N/A
N/A
L-speed
240 [11.5]
263 [12.59 ]
N/A
N/A
N/A
N/A
M-speed
295 [14.1]
344 [16.5]
357 [17]
416
416
N/A
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
19
Specifications and Dimensions
Floor Load Data
Specifications
Dynamic
load frequency, Hz
1Maximum
Speed
35
60
80
100
125
V-speed
15
13.6
12.8
12.8
9.7
11.7
2-speed
8.2
8.0
N/A
N/A
N/A
N/A
L-speed
8.63
7.82
N/A
N/A
N/A
N/A
M-speed
11.58
10.5
9.9
9.9
9.2
N/A
V-speed
2,848 [12.7]
4,146 [18.4]
5,895 [26.2]
6,994 [31.1]
7,028 [31.3]
8,437
[37.52]
2-speed
1,745 [7.8]
2,392 [10.6]
N/A
N/A
N/A
N/A
L-speed
1,797 [8]
2,342
[10.4 ]
N/A
N/A
N/A
N/A
M-speed
2,216 [9.9]
3,066 [13.6]
4,459 [19.8]
5,198 [23]
6,663 [29.6]
N/A
V-speed
4,076 [5.54]
8,492 [11.5]
11,688
[15.9]
14,611
[19.9]
12,488 [17]
17,231
[23.4]
2-speed
1,224 [1.7]
2,985 [4]
N/A
N/A
N/A
N/A
L-speed
1,356 [1.8]
2,826 [3.8]
N/A
N/A
N/A
N/A
M-speed
2,442 [3.3]
5,099 [6.9]
7,029 [9.6]
8,786 [11.9]
11,268
[15.3]
N/A
vertical
load,
Base moment, lbs.-ft
[kN-m]
150
N/A = Not Applicable
1
Acting in the downward direction against the floor.
Table 4
Mounting Bolt Installation Requirements [Approved Foundations Only]
NOTE: If installing epoxy bolts into an elevated concrete foundation pad, the concrete foundation pad
should extend a minimum of 9 inches [229 mm] (for 35
pound machines or 12 inches [305 mm] for 60-150
pound machines out from the machine base on all
sides. Refer to Figure 4 .)
20
A bolt kit consisting of eight bolts is available as an option. 35
machines use 5/8-11 x 8 inch bolts. 60-125 machines use 3/4-10
x 8 inch bolts. 150 machines use 3/4-10 x10 inch grade 5 bolts.
The bolts should be embedded in a 4,000 psi [ 241 bar] minimum
reinforced concrete floor that is a minimum of 6 inches [152 mm]
[for 35 and 60 2-speed, L-speed, and M-speed models] or a 12 inches [305 mm] [for all other models] thick. Use the mounting
bolt layouts in Mounting Bolt Hole Locations section.
On 35–125 machines, the threaded end of the bolts should extend
2 inches [51 mm] above the mounting surface. On 150 machines,
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
the threaded end of the bolts should extend 3 inches [76 mm]
above the mounting surface.
Refer to Figure 5 for a typical installation of individual mounting
bolts.
A
1
B
2
3
C
D
4
5
E
PHM862N_SVG
Acrylic Adhesive Anchors
1. Machine Frame Base
2. Grout
3. Acrylic Adhesive
4. Anchor Bolt [minimum Grade 5 SAE rating]
5. Concrete
Figure 5
Acrylic Adhesive Anchors
A
2 in. [64 mm] [minimum
thread extension]
B
3/4 in. [19 mm]
C
6 in. [165 mm]
D
4 in. [102 mm] [minimum
embedment]
E
Drill hole size per manufacturer requirements
Table 5
1. Place the machine adjacent to the foundation. Do not attempt
to move the machine by pushing on the sides. Always insert a
pry bar or other device under the bottom frame of the machine
to move it into place.
2. Remove the wood skid by unscrewing the carriage bolts holding the skid to the bottom frame of the machine.
3. Place the machine carefully over the anchor bolts. Never attempt to lift the machine by the door handle or by pushing on
the cover panels.
4. Raise and level the machine 0.5 inch [12.7 mm] off the floor
on four points, using spacers such as nut fasteners.
WARNING
Crush hazard. To avoid personal injury and/or
property damage, do not tip the machine more
than 25 degrees in any direction.
W793
5. Fill the space between the machine base and the floor with a
good quality non-shrinking machinery precision grout to
ensure a stable installation. Grout completely under all frame
members [remove front panel and back panel to gain access to
all frame members]. Refer to Table 6 . Force grout under machine base until all voids are filled.
6. Before grout sets completely, make a drain opening in the rear
of the machine grouting with a stiff piece of wire; this opening should be approximately 0.5 inch [12.7 mm] wide to allow any surface water build-up under the base of the machine
to drain away. Do not omit this step.
7. Position the mounting bolt lockwashers and locknuts on the
anchor bolts and finger-tighten locknuts to machine base.
8. Allow machine grout to set, but not cure.
9. Remove the spacers carefully, allowing the machine to settle into the wet grout.
10. After the grout is completely cured, tighten the locknuts by
even increments – one after the other – until all are tightened
evenly and the machine is fastened securely to the floor.
11. Torque 5/8 inch bolts [35 model] to 90 ft.-lbs. and torque 3/4
inch bolts [60-150 models] to 160 ft.-lbs.
NOTE: Check and retighten the locknuts after five to
ten days of operation and every month thereafter. Refer
to Maintenance section.
Machine Mounting and Grouting
After the concrete has cured, proceed as follows:
Grout Placement
IMPORTANT: Grouting is required.
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
21
Specifications and Dimensions
A
E
F
B
C
B
E
G
D
E
A
PHM547N_SVG
PHM574N_SVG
35 Pound 2-Speed Models
35 Pound V-Speed Models
H
H
E
J
M
E
B
I
L
K
E
N
E
PHM548N_SVG
PHM575N_SVG
60 Pound 2-Speed Models
60 Pound V-Speed Models
O
T
W
Q
P
R
S
U
E
V
E
S
E
E
PHM576N_SVG
PHM192N_SVG
80 Pound Models
100 Pound Models
DD
X
Y
EE
E
AA
FF
Z
CC
BB
E
GG
PHM180N_SVG
125 Pound Models
GG
PHM605N_SVG
150 Pound Models
= GROUT
PHM943N_SVG
22
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
A
30.13 in. [765 mm]
R
17.5 in. [445 mm]
B
36 in. [914 mm]
S
33 in. [838 mm]
C
17.88 in. [454 mm]
T
41.13 in. [1044 mm]
D
20 in. [508 mm]
U
43.81 in. [1113 mm]
E
4.06 in. [103 mm] typical
V
20.69 in. [526 mm]
F
27.88 in. [708 mm]
W
10.88 in. [276 mm]
G
22 in. [559 mm]
X
48 in. [1219 mm]
H
35.63 in. [905 mm]
Y
3.25 in. [83 mm]
I
35.94 in. [913 mm]
Z
48 in. [219 mm]
J
11.94 in. [303 mm]
AA
24.31 in. [617 mm]
K
27.5 in. [699 mm]
BB
39.88 in. [1013 mm]
L
12 in. [305 mm]
CC
22 in. [559 mm]
M
27.88 in. [708 mm]
DD
50 in. [1270 mm]
N
27.5 in. [699 mm]
EE
34 in. [863.6 mm]
O
41.13 in. [1044 mm]
FF
56 in. [1422 mm]
P
43.75 in. [1111 mm]
GG
8 in. [203.2 mm] typical
Q
14 in. [356 mm]
Table 6
Mounting Bolt Hole Locations
IMPORTANT: All drawings are not to scale.
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
23
Specifications and Dimensions
B
C
A
E
D
G
F
I
H
K
J
J
L
1
PHM630N_SVG
35 Pound Models
1. Front of Machine
Figure 6
Mounting Bolt Hole Locations – 35 Pound Models
A
36 in. [914 mm]
B
28.63 in. [727 mm]
C
0.75 in. [19 mm]
D
43.28 in. [1089 mm]
E
30.19 in. [767 mm]
24
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
Mounting Bolt Hole Locations – 35 Pound Models
F
40.19 in. [1022 mm]
G
34.5 in. [876 mm]
H
34.16 in. [868 mm]
I
21.19 in. [538 mm]
J
2 in. [51 mm]
K
26.13 in. [664 mm]
L
30.13 in. [765 mm]
Table 7
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
25
Specifications and Dimensions
A
A
B
D
E
C
H
F
I
I
G
J
K
L
L
M
A
N
1
PHM631N_SVG
60 Pound V-speed Models
1. Front of Machine
Figure 7
Mounting Bolt Hole Locations – 60 Pound Models [V-speed]
A
0.75 in. [19 mm]
B
34.13 in. [867 mm]
C
44.81 in. [1138 mm]
D
4.81 in. [122 mm]
E
9 in. [229 mm]
26
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
Mounting Bolt Hole Locations – 60 Pound Models [V-speed]
F
1.25 in. [32 mm]
G
39.25 in. [997 mm]
H
10.75 in. [273 mm]
I
36 in. [914 mm]
J
34.56 in. [878 mm]
K
10.69 in. [271 mm]
L
2 in. [51 mm]
M
31.63 in. [803 mm]
N
35.63 in. [905 mm]
Table 8
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
27
Specifications and Dimensions
A
B
A
A
D
G
C
E
F
H
E
I
J
A
L
K
K
M
1
PHM666N_SVG
60 Pound 2-speed Models
1. Front of Machine
Figure 8
Mounting Bolt Hole Locations – 60 Pound Models [2-speed]
A
0.75 in. [19 mm]
B
34.13 in. [867 mm]
C
46.81 in. [1189 mm]
D
4.19 in. [122 mm]
E
1.25 in. [32 mm]
F
44.81 in. [1138 mm]
28
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
Mounting Bolt Hole Locations – 60 Pound Models [2-speed]
G
9 in. [229 mm]
H
36 in. [914 mm]
I
39.25 in. [997 mm]
J
21.44 in. [554 mm]
K
2 in. [51 mm]
L
31.75 in. [803 mm]
M
35.63 in. [905 mm]
Table 9
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
29
Specifications and Dimensions
A
A
B
C
D
G
E
F
H
I
K
J
H
K
L
L
M
A
1
PHM632N_SVG
80 and 100 Pound Models
1. Front of Machine
Figure 9
Mounting Bolt Hole Locations – 80 and 100 Pound Models
A
0.75 in. [19 mm]
B
39.63 in. [1008 mm]
C
6.75 in. [171 mm]
D
9 in. [229 mm]
30
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
Mounting Bolt Hole Locations – 80 and 100 Pound Models
E
43.75 in. [1111 mm]
F
2.25 in. [57 mm]
G
52.19 in. [1326 mm]
H
13.63 in. [346 mm]
I
46.31 in. [1176 mm]
J
39.75 in. [1010 mm]
K
35.13 in. [892 mm]
L
3 in. [76 mm]
M
41.13 in. [1045 mm]
Table 10
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
31
Specifications and Dimensions
A
A
B
C
D
F
E
G
H
I
J
K
K
F
1
A
PHM633N_SVG
125 Pound Models
1. Front of Machine
Figure 10
Mounting Bolt Hole Locations – 125 Pound Models
A
0.75 in. [19 mm]
B
46.5 in. [1181 mm]
C
7 in. [178 mm]
32
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
Mounting Bolt Hole Locations – 125 Pound Models
D
10 in. [254 mm]
E
61.5 in. [1562 mm]
F
48 in. [1219 mm]
G
55.47 in. [1409 mm]
H
15 in. [381 mm]
I
48.94 in. [1243 mm]
J
15.25 in. [387 mm]
K
23.25 in. [591 mm]
Table 11
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
33
Specifications and Dimensions
A
B
A
D
C
E
F
G
I
H
J
K
K
L
M
1
PHM778N_SVG
150 Pound Models
1. Front of Machine
Figure 11
Mounting Bolt Hole Locations – 150 Pound Models
A
10.38 in. [264 mm]
B
48.13 in. [1223 mm]
C
56 in. [1422 mm]
D
51.38 in. [1305 mm]
34
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
Mounting Bolt Hole Locations – 150 Pound Models
E
47.88 in. [1216 mm]
F
57.4 in. [1457 mm]
G
12.13 in. [308 mm]
H
15 in. [381 mm]
I
67.1 in. [1704 mm]
J
4 in. [102 mm]
K
1.5 in. [38.1 mm]
L
47 in. [1193 mm]
M
50 in. [1270 mm]
Table 12
Gap Setting for Vibration Switch
After the machine has been properly installed, the vibration
switch gap must be verified. To locate the vibration switch refer
to Figure 12 , Figure 13 and Figure 14 . For UniLinc models,
while the control is displaying the Inputs Outputs Menu the alarm
will sound when the frame switch is activated. To verify and set
the vibration switch gap use the following procedures:
WARNING
Only trained personnel should perform this procedure. Use caution while servicing machines with
covers removed and power applied.
W700
For UniLinc Models, Navigate to the Inputs Outputs
Menu:
2. Press the arrow keys to highlight the Diagnostic box.
3. Press the
key to enter the Diagnostic Menu.
4. Press the
key to enter the Test Menu.
5. Press the arrow keys to highlight the Inputs Outputs box.
6. Press the
key to enter the Inputs Outputs Menu.
Verify Vibration Switch Gap [35-125 Pound Models]:
1. Insert 0.009 inch feeler gauge between the adjustment bolt
and the vibration switch; the alarm must not activate.
2. Remove the feeler gauge.
3. Insert 0.010 inch feeler gauge [supplied with machine] between the adjustment bolt and the vibration switch; the alarm
must activate.
4. Remove the feeler gauge.
5. Adjust the vibration switch adjustment bolt if necessary. Refer toFigure 12 and Figure 13 .
1.
From the Cycle Menu press and hold the
,
,
keys to enter the System Menu.
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
35
Specifications and Dimensions
1
2
PHM794N_SVG
35 Pound Models
1. Adjustment Bolt
2. Vibration Switch
Figure 12
1
2
PHM795N_SVG
60, 80, 100 and 125 Pound Models
1. Adjustment Bolt
2. Vibration Switch
Figure 13
Verify Safety Switch Operation [150 Pound Design 2
Models]:
Place a large magnet above the normally-closed ball switch to
verify switch operation. Refer to Figure 14 .
36
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
IMPORTANT: UW150 Design 2 machines are manufactured with a normally-closed ball switch and
should not require any adjustment. To avoid nuisance tripping, machine must be level with a summed value of 3/8 inch [ 9.5 mm] front to back and
right to left to the earth. If switch is tripped, check if
machine is level and then for poor grouting and broken anchor bolts. DO NOT BYPASS SAFETY
SWITCH. Contact a qualified service technician for
further assistance.
1
PHM716N_SVG
150 Pound Models
1. Vibration Switch
Figure 14
Drain Connection Requirements
Figure 15 and Figure 16 show typical direct drain and drain
trough installations.
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
37
Specifications and Dimensions
1
3
2
2
1
9
3
4
4
5
6
A
8
5
7
7
6
8
PHM830N_SVG
PHM829N_SVG
Direct Drain System
1. Drain Pipe
2. Overflow Pipe (optional)
3. Vent
4. Trap (if required by local codes)
5. Steel Grate
6. Drain Trough
7. Strainer
8. Waste Line
9. 3 in. [76 mm] minimum gap
Figure 15
All drain systems must be vented to prevent an air lock and to
prevent siphoning.
Drain Trough System
1. Rear of Machine
2. Drain Pipe
3. Overflow Pipe (optional)
4. Steel Grate
5. Drain Trough
6. Strainer
7. Waste Line
8. 1 in. [25 mm] minimum gap
9. 3 in. [76 mm] minimum gap
Figure 16
Refer to Table 13 for capacity-specific drain information.
Refer to Figure 15 .
NOTE: Installation of additional machines will require
proportionately larger drain connections. Refer to Table
14 .
IMPORTANT: Machines must be installed in accordance with all local codes and ordinances.
IMPORTANT: Do not block the machine overflow opening.
If proper drain size is not available or practical, a surge tank is
required. A surge tank along with a sump pump should be used
when gravity drainage is not possible.
If water or suds flow from the machine overflow vent and the
machine has been verified to be operating properly with proper
water levels and correct amount of laundry chemicals, a drain
line may be added to the machine overflow vent and routed to a
drain trough.
Increasing the drain hose length, installing elbows, or causing
bends will decrease drain flow rate and increase drain times, impairing machine performance.
1. Route a drain pipe from the machine overflow to a drain
trough. Drain pipe should be routed straight across or down
and be suspended above drain trough by at least 3 inches [76
mm].
IMPORTANT: Do not route the machine overflow to a
direct drain system.
38
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
Drain Information
Specifications
35
60
80
100
125
150
Drain connection size,
I.D., in. [mm] with second drain:
2.375
[60]
3 [76]
3 [76]
3 [76]
3 [76]
3 [76]
Number of drain outlets
1
1
2 [UniLinc]
2 [UniLinc]
2 [UniLinc]
2
1 [M30]
1 [M30]
1 [M30]
Drain flow capacity, gal/
min. [l/min.]
35
[132]
64
[242]
120
[454]
120
[454]
140 [530]
140 [530]
Recommended drain pit
size, ft 3 [l]
5 [142]
6 [170]
9 [255]
11
[311]
13 [368]
13 [368]
†Sized for one machine using overflow level.
Table 13
Drain Line Sizing/Minimum Drain I.D., in. [mm]
Number of Machines
Model
1
2
3
4
35
3 [76]
3 [76]
3.5 [89]
4 [102]
60
3 [76]
4 [102]
6 [152]
6 [152]
80
4 [102]
6 [152]
6 [152]
8 [203]
100
4 [102]
6 [152]
6 [152]
8 [203]
125
4 [102]
6 [152]
6 [152]
8 [203]
150
4 [102]
6 [152]
6 [152]
8 [203]
Table 14
stallation of additional machines will require proportionately
larger water lines. Refer to Table 16 .
Water Connection
Connections should be supplied by hot and cold water lines of at
least the sizes shown in the Water Supply Line Sizing table. In-
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
39
Specifications and Dimensions
Maximum water inlet temperature is 190 °Fahrenheit [ 88 °Celsius].
WARNING
To prevent personal injury, avoid contact with inlet
water temperatures higher than 125° Fahrenheit [51°
Celsius] and hot surfaces.
W748
Water Supply Information
Specifications
35
60
80/100
125/150
Number of main fill water inlets
2
2
2
2
Main fill water inlet size at machine, in.
[mm]
3/4
3/4
3/4
1
Factory supplied
hose
Size
19
19
19
25.4
Thread
11.5
11.5
11.5
56
Number of spray rinse water inlets
2
2
2
2
Spray rinse water inlet size, in. [mm]
3/4 [19]
3/4 [19]
3/4 [19]
3/4 [19]
Recommended pressure psi [bar]
30–8 [52–5.7 ]
Inlet flow capacity, gal/min [l/min] at
80 psi
28 [106]
39 [148]
50 [189]
75 [284]
Table 15
To connect water service to machine with rubber hoses, use the
following procedure:
1. Before installing hoses, flush the water system for at least two
minutes.
2. Check filters in the machine’s inlet hoses for proper fit and
cleanliness before connecting.
3. Hang the hoses in a large loop; do not allow them to kink.
If additional hose lengths are needed or using hoses other than
those supplied by manufacturer, flexible hoses with screen filters
are required.
Lower pressures will increase fill times.
Suitable air cushions [risers] should be installed in supply lines to
prevent “hammering.” Refer to Figure 17 .
Connect machine to a backflow preventer (vacuum breaker) before connecting to the public water main in all countries where
local regulations require specific water approval certificates.
40
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
Water Supply Line Sizing
1
2
Supply Line Size, in. [mm]
Model
Number of
Machines
Main
Hot/Cold
3
4
100
5
3
2 [51]
1.5 [38]
4
2.5 [64]
2 [51]
1
1.5 [38]
1 [25]
2
2 [51]
1.5 [38]
3
2 [51]
1.5 [38]
4
2.5 [64]
2 [51]
1
2 [51]
1.25 [32]
2
2.5 [64]
2 [51]
3
2.5 [64]
2 [51]
4
2.5 [64]
2.5 [64]
1
2 [51]
1.25 [32]
PHM831N_SVG
1.
2.
3.
4.
5.
Air Cushions (Risers)
Water Supply Faucets
Double Check Valves
Filters
Hoses
125
Figure 17
Water Supply Line Sizing
Supply Line Size, in. [mm]
Model
35
60
80
F8423301ENR3
Number of
Machines
Main
Hot/Cold
1
1 [25]
0.75 [19]
2
1.5 [38]
1 [25]
2
2.5 [64]
2 [51]
3
2 [51]
1.25 [32]
3
2.5 [64]
2 [51]
4
2 [51]
1.5 [38]
4
2.5 [64]
2.5 [64]
1
1.25 [32]
1 [25]
2
2 [51]
1.25 [32]
3
2 [51]
1.5 [38]
4
2.5 [64]
2 [51]
1
1.25 [32]
1 [25]
2
2 [51]
1.25 [32]
150
Table 16
Electrical Installation Requirements
IMPORTANT: Electrical ratings are subject to change.
Refer to serial decal for electrical ratings information
specific to your machine.
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
41
Specifications and Dimensions
WARNING
Electrical shock hazard will result in death or serious injury. Disconnect electric power and wait three
(3) minutes before servicing.
PHM756N_SVG
N, P and R–voltage Models
W784
On V-speed models, the AC inverter drive requires a clean power
supply free from voltage spikes and surges. Use a voltage monitor to check incoming power.
WARNING
Dangerous voltages are present inside the machine.
Only qualified personnel should attempt adjustments and troubleshooting. Disconnect power from
the machine before removing any cover and guards,
and before attempting any service procedures.
W736
WARNING
W360
Electrical connections are made at the rear of the machine. The
machine must be connected to the proper electrical supply shown
on the identification plate attached to the rear of the machine, using copper conductors only.
IMPORTANT: Alliance Laundry Systems warranty does
not cover components that fail as a result of improper
input voltage.
Make sure the correct transformer jumper [208 Volt or 240 Volt]
is in place. Refer to the “optional” Electrical Service Conversion
label located on the back of the machine near the electrical service input for machine electrical requirements. Refer to Figure 18
and Figure 19 .
This unit may be field converted
by a QUALIFIED Electrician to
the following 200-208 Volts
and/or 50 Hertz.
PRIOR TO CONNECTING
ELECTRICAL SERVICE,
COMPLETE THE FOLLOWING
F8099701R1
200-208 VAC CONVERSION
VAC: 200-208
PHASE: *
AMPS: *
WIRES & GROUND: *
REC'D BREAKER: *
1. Refer to the Control Transformer area on
the Control Option Diagram.
2. Remove the "240V" Transf ormer Jumper in
the control box.
3. Replace with "208V" Transformer Jumper
found in the diagram pack.
4. Sign off below.
200-208VAC
Operation
(SIGN)
* As indicated on
original serial plate
Transformer Jumper
208V
50Hz CONVERSION
1. Refer to the Control Option Diagram.
2. Remove the wire from the 60Hz tap on drain
valve(s).
3. Connect the wire to the 50Hz Tap on all
drain valves.
Connection Drain Valve(s)
4. Sign off below.
for 50Hz
Operation Only
50Hz
60Hz N
on
(DATE)
50Hz
Operation
on
(SIGN)
(DATE)
PHM740N_SVG
O, Q, X and Y–voltage Models
Figure 18
42
The following conditions require corrective action, contact the local utility to adjust the voltage.
•
•
If the local utility cannot adjust the input voltage, install a
buckboost transformer to lower the input voltage.
Input voltage is above 240V or 480V, phase to ground voltage
exceeds 125% of normal line to line voltage, or 240V open
delta configuration (stinger leg).
Contact a qualified electrical maintenance person for assistance.
Hazardous Voltage. Can cause shock, burn or death.
Verify that a ground wire from a proven earth ground
is connected to the lug near the input power block
on this machine.
OPTIONAL ELECTRICAL SERVICE
CONNECTION BASED ON
AVAILABILITY
Figure 19
On V-speed models, the AC drive provides thermal overload protection for the drive motor. However, a separate three-phase circuit breaker must be installed for complete electrical overload
protection. This prevents damage to the motor by disconnecting
all legs if one should be lost accidentally. Check the nameplate
on the back of the machine for recommended circuit breaker requirements size.
IMPORTANT: Do NOT use fuses in place of a circuit
breaker.
CAUTION
Do not use a phase adder on any variable-speed machine.
SW037
The machine should be connected to an individual branch circuit
not shared with lighting or other equipment.
The connection should be shielded in a liquid-tight or approved
flexible conduit with proper conductors of correct size installed
in accordance with applicable codes. The connection must be
made by a qualified electrician using the wiring diagram provided with the machine, or according to accepted European standards.
Refer to nameplate for recommended circuit breaker size and determine wire size based on local code requirements.
Refer to nameplate for recommended wire sizes for runs up to 50
feet [15.24 meters]. Use next larger size for runs of 50 to 100 feet
[15.24 to 30.48 meters]. Use 2 sizes larger for runs greater than
100 feet [30.48 meters].
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
For personal safety and for proper operation, the machine must
be grounded in accordance with state and local codes or accepted
European standards. The ground connection must be made to a
proven earth ground, not to conduit or water pipes. Refer to Figure 20 and Figure 21 .
1
SERVICE
GROUND
2
CHASIS
L1
L2
2
L1
L3
L2
1
TB1
PHM721N_SVG
L3
SERVICE
GROUND
Machines without Electric Heat
1. Grounding Lug: Connect to proven earth ground
2. Customer Input Power Terminal
CHASIS
3
Figure 21
Machines can be converted for lower voltage operation and/or 50
Hz operation. Refer to conversion label by nameplate for details.
TB1
PHM700N_SVG
Machines with Electric Heat
1. Grounding Lug: Connect to proven earth ground
2. Customer Input Power Terminals
3. Internal Load Distribution - DO NOT connect customer
power source or load
Electrical Specifications
North American Approval
Figure 20
35 Pound Capacity Models
Voltage Designation
Code
Voltage
X
Q
Standard
Specifications
Cycle
Phase
Wire
Standard
Standard
Electric
Heat
F8423301ENR3
AWG
mm2
50/60
1/3
2/3
15/8
20/15
12/14
4/2.5
200–240
50/60
3
3
8
15
14
2.5
42
50
6
16
7
20
12
4
38
50
6
16
6
15
14
2.5
23
30
10
6
208–240
60
3
3
Electric
Heat
R (Through
7/6/10)
Breaker
200–240
Electric
Heat
O**
Full
Load
Amps
380–480
50/60
3
3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
43
Specifications and Dimensions
35 Pound Capacity Models
Voltage Designation
Code
N (Starting
7/7/10)
Voltage
Standard
440-480
Specifications
Cycle
50/60
Phase
3
Wire
3
Electric
Heat
P (Starting
7/7/10)
Standard
380-415
50/60
3
Full
Load
Amps
3
Electric
Heat
Breaker
AWG
mm2
6
15
14
2.5
23
30
10
6
6
15
14
2.5
23
30
10
6
NOTE: Wire sizing listed in these tables is based on Article 310, Table 310.16 of the NEC; at 104°F [40°C] ambient temperature. Follow your local electrical codes. Use only copper conductors, rated for 194°F [90ºC] or
higher, type THHN or better. No more than three current carrying conductors per raceway. Contact your local
Authority having jurisdiction if you have questions. Circuit breakers should be UL 489 listed or better. Single
phase circuit breakers for single phase machines only; three phase circuit breakers for all others.
**M30 Control Models Only.
Table 17
60 Pound Capacity Models
Voltage Designation
Code
Voltage
X
Q
Standard
Specifications
Cycle
Phase
Wire
Standard
Electric
Heat
44
Breaker
AWG
mm2
200–240
50/60
1/3
2/3
15/9
20/15
12/14
4/2.5
200–240
50/60
3
3
9
15
14
2.5
71
80
3
25
11
30
10
6
66
80
3
30
Electric
Heat
O**
Full
Load
Amps
208–240
60
3
3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
60 Pound Capacity Models
Voltage Designation
Code
R (Through
7/6/10)
Voltage
Standard
380–480
Specifications
Cycle
50/60
Phase
3
Wire
3
Electric
Heat
N (Starting
7/7/10)
Standard
440-480
50/60
3
3
Electric
Heat
P (Starting
7/7/10)
Standard
380-415
50/60
3
Full
Load
Amps
3
Electric
Heat
Breaker
AWG
mm2
7
15
14
2.5
37
40
8
10
7
15
14
2.5
37
40
8
10
7
15
14
2.5
37
40
8
10
NOTE: Wire sizing listed in these tables is based on Article 310, Table 310.16 of the NEC; at 104°F [40°C] ambient temperature. Follow your local electrical codes. Use only copper conductors, rated for 194°F [90ºC] or
higher, type THHN or better. No more than three current carrying conductors per raceway. Contact your local
Authority having jurisdiction if you have questions. Circuit breakers should be UL 489 listed or better. Single
phase circuit breakers for single phase machines only; three phase circuit breakers for all others.
**M30 Control Models Only.
Table 18
80 Pound Capacity Models
Voltage Designation
Code
Q (Through
4/13/10)
Voltage
Standard
Electric
Heat
F8423301ENR3
200–240
Specifications
Cycle
50/60
Phase
3
Wire
3
Full
Load
Amps
Breaker
AWG
mm2
14
15
14
2.5
105
110
1
50
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
45
Specifications and Dimensions
80 Pound Capacity Models
Voltage Designation
Code
Q (Starting
4/14/10)
Voltage
Standard
208–240
Specifications
Cycle
50/60
Phase
3
Wire
3
Electric
Heat
R (Through
7/6/10)
Standard
380–480
50/60
3
3
Electric
Heat
N (Starting
7/7/10)
Standard
440-480
50/60
3
3
Electric
Heat
P (Starting
7/7/10)
Standard
380-415
50/60
3
Electric
Heat
3
Full
Load
Amps
Breaker
AWG
mm2
14
20
12
4
105
110
1
50
10
15
14
2.5
39
40
8
10
10
15
14
2.5
39
40
8
10
10
15
14
2.5
39
40
8
10
NOTE: Wire sizing listed in these tables is based on Article 310, Table 310.16 of the NEC; at 104°F [40°C] ambient temperature. Follow your local electrical codes. Use only copper conductors, rated for 194°F [90ºC] or
higher, type THHN or better. No more than three current carrying conductors per raceway. Contact your local
Authority having jurisdiction if you have questions. Circuit breakers should be UL 489 listed or better. Single
phase circuit breakers for single phase machines only; three phase circuit breakers for all others.
Table 19
46
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
100 Pound Capacity Models
Voltage Designation
Code
Q (Through
4/13/10)
Voltage
Standard
200–240
Specifications
Cycle
50/60
Phase
3
Wire
3
Electric
Heat
Q (Starting
4/14/10)
Standard
208–240
50/60
3
3
Electric
Heat
R (Through
7/6/10)
Standard
380–480
50/60
3
3
Electric
Heat
N (Starting
7/7/10)
Standard
440-480
50/60
3
3
Electric
Heat
P (Starting
7/7/10)
Standard
380-415
50/60
3
Electric
Heat
3
Full
Load
Amps
Breaker
AWG
mm2
10
15
14
2.5
108
110
1
50
14
20
12
2.5
108
110
1
50
10
15
14
2.5
40
50
6
16
10
15
14
2.5
40
50
6
16
10
15
14
2.5
40
50
6
16
NOTE: Wire sizing listed in these tables is based on Article 310, Table 310.16 of the NEC; at 104°F [40°C] ambient temperature. Follow your local electrical codes. Use only copper conductors, rated for 194°F [90ºC] or
higher, type THHN or better. No more than three current carrying conductors per raceway. Contact your local
Authority having jurisdiction if you have questions. Circuit breakers should be UL 489 listed or better. Single
phase circuit breakers for single phase machines only; three phase circuit breakers for all others.
Table 20
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
47
Specifications and Dimensions
125 Pound Capacity Models
Voltage Designation
Code
Voltage
Specifications
Cycle
Phase
Full
Load
Amps
Wire
Breaker
AWG
mm2
Q
200–240
50/60
3
3
12
15
14
2.5
R (Through 7/6/10)
380–480
50/60
3
3
8
15
14
2.5
N (Starting
7/7/10)
440-480
50/60
3
3
8
15
14
2.5
74
80
4
25
8
15
14
2.5
65
70
4
25
Standard
Electric
Heat
P (Starting
7/7/10)
Standard
380-415
50/60
3
3
Electric
Heat
NOTE: Wire sizing listed in these tables is based on Article 310, Table 310.16 of the NEC; at 104°F [40°C] ambient temperature. Follow your local electrical codes. Use only copper conductors, rated for 194°F [90ºC] or
higher, type THHN or better. No more than three current carrying conductors per raceway. Contact your local
Authority having jurisdiction if you have questions. Circuit breakers should be UL 489 listed or better. Single
phase circuit breakers for single phase machines only; three phase circuit breakers for all others.
Table 21
150 Pound Capacity Models
Voltage Designation
Code
Voltage
Specifications
Cycle
Phase
Wire
Full Load
Amps
Breaker
AWG
mm2
Q
200–240
50/60
3
3
16
20
12
4
R (Through
7/6/10)
380–480
50/60
3
3
11
15
14
2.5
N (Starting
7/7/10)
440-480
50/60
3
3
11
15
14
2.5
P (Starting
7/7/10)
380-415
50/60
3
3
11
15
14
2.5
48
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
150 Pound Capacity Models
Voltage Designation
Code
Voltage
Specifications
Cycle
Phase
Wire
Full Load
Amps
Breaker
AWG
mm2
NOTE: Wire sizing listed in these tables is based on Article 310, Table 310.16 of the NEC; at 104°F [40°C] ambient temperature. Follow your local electrical codes. Use only copper conductors, rated for 194°F [90ºC] or
higher, type THHN or better. No more than three current carrying conductors per raceway. Contact your local
Authority having jurisdiction if you have questions. Circuit breakers should be UL 489 listed or better. Single
phase circuit breakers for single phase machines only; three phase circuit breakers for all others.
Table 22
CE Approval
35 Pound Capacity Models
Voltage Designation
Code
Voltage
X
Q
Standard
Specifications
Cycle
Phase
Wire
Full Load
Amps
Breaker
mm2
200–240
50/60
1/3
2/3
12/8
16/10
2.5
200–240
50/60
3
3
8
10
2.5
42
50
10
Electric
Heat
O**
208–240
60
3
3
17
20
4
N
440-480
50/60
3
3
23
25
2.5
380-415
50/60
3
3
7
10
2.5
23
25
2.5
P
Standard
Electric
Heat
NOTE: Follow your local electrical codes. Use only copper conductors, rated for 194°F [90ºC] or higher, type
THHN or better. No more than three current carrying conductors per raceway. Contact your local Authority
having jurisdiction if you have questions. Circuit breakers should be UL 489 listed or better. Single phase circuit breakers for single phase machines only; three phase circuit breakers for all others.
**M30 Control Models Only.
Table 23
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
49
Specifications and Dimensions
60 Pound Capacity Models
Voltage Designation
Code
Voltage
X
Q
Standard
Specifications
Cycle
Phase
Wire
Full Load
Amps
Breaker
mm2
200–240
50/60
1/3
2/3
17/11
20/16
2.5
200–240
50/60
3
3
11
16
2.5
71
80
16
Electric
Heat
O**
208–240
60
3
3
26
32
2.5
N
440–480
50/60
3
3
37
40
4
380-415
50/60
3
3
7
10
2.5
37
40
4
P
Standard
Electric
Heat
NOTE: Follow your local electrical codes. Use only copper conductors, rated for 194°F [90ºC] or higher, type
THHN or better. No more than three current carrying conductors per raceway. Contact your local Authority
having jurisdiction if you have questions. Circuit breakers should be UL 489 listed or better. Single phase circuit breakers for single phase machines only; three phase circuit breakers for all others.
**M30 Control Models Only.
Table 24
80 Pound Capacity Models
Voltage Designation
Code
Q
Voltage
Standard
Electric
Heat
50
208–240
Specifications
Cycle
50/60
Phase
3
Wire
3
Full Load
Amps
Breaker
mm2
17
20
2.5
105
125
50
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
80 Pound Capacity Models
Voltage Designation
Code
N
Voltage
Standard
440-480
Specifications
Cycle
50/60
Phase
3
Wire
3
Electric
Heat
P
Standard
380-415
50/60
3
3
Electric
Heat
Full Load
Amps
Breaker
mm2
11
16
2.5
39
40
4
11
16
2.5
39
40
4
NOTE: Follow your local electrical codes. Use only copper conductors, rated for 194°F [90ºC] or higher, type
THHN or better. No more than three current carrying conductors per raceway. Contact your local Authority
having jurisdiction if you have questions. Circuit breakers should be UL 489 listed or better. Single phase circuit breakers for single phase machines only; three phase circuit breakers for all others.
Table 25
100 Pound Capacity Models
Voltage Designation
Code
Q
Voltage
Standard
208–240
Specifications
Cycle
50/60
Phase
3
Wire
3
Electric
Heat
N
Standard
440-480
50/60
3
3
Electric
Heat
P
Standard
Electric
Heat
F8423301ENR3
380-415
50/60
3
3
Full Load
Amps
Breaker
mm2
17
20
2.5
108
125
50
11
16
2.5
41
50
10
11
16
2.5
41
50
10
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
51
Specifications and Dimensions
100 Pound Capacity Models
Voltage Designation
Code
Voltage
Specifications
Cycle
Phase
Wire
Full Load
Amps
Breaker
mm2
NOTE: Follow your local electrical codes. Use only copper conductors, rated for 194°F [90ºC] or higher, type
THHN or better. No more than three current carrying conductors per raceway. Contact your local Authority
having jurisdiction if you have questions. Circuit breakers should be UL 489 listed or better. Single phase circuit breakers for single phase machines only; three phase circuit breakers for all others.
Table 26
125 Pound Capacity Models
Voltage Designation
Code
Voltage
Q
N
Standard
Specifications
Cycle
Phase
Wire
Standard
Breaker
mm2
200–240
50/60
3
3
12
16
2.5
440-480
50/60
3
3
11
16
2.5
74
80
16
11
16
2.5
65
80
16
Electric
Heat
P
Full Load
Amps
380-415
50/60
3
Electric
Heat
3
NOTE: Follow your local electrical codes. Use only copper conductors, rated for 194°F [90ºC] or higher, type
THHN or better. No more than three current carrying conductors per raceway. Contact your local Authority
having jurisdiction if you have questions. Circuit breakers should be UL 489 listed or better. Single phase circuit breakers for single phase machines only; three phase circuit breakers for all others.
Table 27
52
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
150 Pound Capacity Models
Voltage Designation
Code
Voltage
Specifications
Cycle
Phase
Wire
Full Load
Amps
Breaker
mm2
Q
200–240
50/60
3
3
17
20
2.5
N
440-480
50/60
3
3
11
16
2.5
P
380-415
50/60
3
3
11
16
2.5
NOTE: Follow your local electrical codes. Use only copper conductors, rated for 194°F [90ºC] or higher, type
THHN or better. No more than three current carrying conductors per raceway. Contact your local Authority
having jurisdiction if you have questions. Circuit breakers should be UL 489 listed or better. Single phase circuit breakers for single phase machines only; three phase circuit breakers for all others.
Table 28
Steam Requirements (Steam Heat Option Only)
For machines equipped with optional steam heat, install piping in
accordance with approved commercial steam practices. Steam requirements are shown in .Table 29 .
WARNING
Hot Surfaces. Will cause severe burns. Turn steam
off and allow steam pipes, connections and components to cool before touching.
W505
Steam Supply Information
Capacities
35
60
80
100
125/150
Steam inlet connection, in. [mm]
1/2 [DN13]
1/2 [DN13]
1/2 [DN13]
1/2 [DN13]
3/4 [DN19]
Number of steam
inlets
1
1
1
1
1
Recommended
pressure, psi [bar]
30–80 [2.0–5.5]
30–80 [2.0–5.5]
30–80 [2.0–5.5]
30–80 [2.0–5.5]
30–80 [2.0–5.5]
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
53
Specifications and Dimensions
Steam Supply Information
Capacities
Maximum pressure, psi [bar]
35
60
80 [5.5]
80
80 [5.5]
80 [5.5]
100
80 [5.5]
125/150
80 [5.5]
Table 29
IMPORTANT: Failure to install the customer supplied
steam filter may void the warranty.
Chemical Injection Supply System
WARNING
IMPORTANT: Undiluted chemical dripping can damage
the machine. All chemical injection supply dispenser
pumps and dispenser tubing should be mounted below
the machine’s injection point. Loops do not prevent
drips if these instructions are not followed. Figure 22
shows a typical Chemical Injection Supply System.
IMPORTANT: Failure to follow these instructions could
damage the machine and void the warranty.
Dangerous Chemicals. May damage eyes and skin.
Wear eye and hand protection when handling chemicals; always avoid direct contact with raw chemicals. Read the manufacturer’s directions for accidental contact before handling chemicals. Ensure an
eye-rinse facility and an emergency shower are within easy reach. Check at regular intervals for chemical leaks.
W363
2
3
1
4
PHM825N_SVG
1.
2.
3.
4.
Injection Point
Loops
Chemical Dispenser Pump Outlet
PVC Pipe
Figure 22
54
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
Connecting External Liquid Supplies
1. Remove knockout from supply dispenser. Refer to Figure 23 .
Plugs are assembled inside the tubing ring.
2. Install strain relief connector in hole with strain reliefs, included in the seal nut.
3. Insert tubes through base. Do not remove cups. Tube should
extend into the plastic cup, with the exception of the softener
tube, which should be routed to the outside of the cup.
4. Tighten the seal nut to prevent tubing from escaping the assembly.
5. Before operating machine, confirm lid is completely closed.
Chemical Injection Supply System
Number of external liquid
supply connections
8
Liquid supply connection
size, in. [mm]
0.625 [15.9 ]
Table 30
Do not attempt to make chemical injection electrical connections
to points other than those provided specifically for that purpose
by the factory.
Chemical Injection Supply System
Number of dry supply compartments
F8423301ENR3
5
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
55
Specifications and Dimensions
1
2
3
12
4
5
6
7
8
9
10
11
PHM832N_SVG
1. Strain Relief for Liquid Chemical Supply Lines
2. Seal Nut
3. Supply Dispenser Lid
4. Tubing Ring
5. Base
6. Nozzles
7. Tubing
8. Nut
9. Dry Supply Cups
10. Dry Supply Insert
11. Polypropylene Supply Dispenser
12. Knockout
IMPORTANT: Do not attach anything to nozzles. Air gap must be maintained.
Figure 23
Connecting External Liquid Supplies to the Machine
with Optional Five Compartment Supply Dispenser
56
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
1
2
3
4
5
6
PHM553N_SVG
IMPORTANT: Do not attach anything to nozzles. Air gap must be maintained.
Five Compartment Supply Dispenser (Optional)
1. Strain Relief for Liquid Chemical Supply Lines
2. Supply Dispenser Lid
3. Nozzles
4. Dry Supply Cups
5. Dry Supply Insert
6. Polypropylene Supply Dispenser
Figure 24
1. Remove knockout from supply dispenser. Refer to Figure 24 .
Plugs are assembled inside the tubing ring.
2. Install PG connector in hole with strain reliefs, included in the
seal nut.
3. Insert tubes through PG base. Do not remove cups. Tube
should extend into the plastic cup, with the exception of the
F8423301ENR3
softener tube, which should be routed to the outside of the
cup.
4. Tighten the seal nut to prevent tubing from escaping the assembly.
5. Before operating machine, confirm lid is completely closed.
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
57
Specifications and Dimensions
Do not attempt to make chemical injection electrical connections
to points other than those provided specifically for that purpose
by the factory.
2
3
1
4
PHM940N_SVG
* Use a check valve on the end of tubing
† Must be mounted below the injection point
1.
2.
3.
4.
Injection Point*
Loops
Chemical Dispenser Pumb Outlet †
PVC Pipe
Figure 25
External Supplies
For proper communication between the machine and an external
chemical supply system, it is important for the low-voltage signal
power to be connected properly. The included wiring diagram
shows several different options for safe and correct wiring of this
interface.
The preferred method for connecting the wiring from the external
chemical supply system to the machine is to use the 300mA power of the machine’s 24VAC control transformer, which is intended strictly for this purpose. Other voltage and current options
are available, but require some wiring changes and must be provided with an external power source. Under no circumstances
should the high-voltage machine supply connections or source be
used for the communication wiring.
EXTERNAL DISPENSER CONNECTIONS
EXAMPLE FOR EXTERNAL
ES 1 DISPENSER CONNECTION
RELAY COM
ES 2
ES 3
ES 4
ES 5
ES 6
SUPPLY 1
24 VAC
External
Dispensing
System
24 VAC COM
ES 7 JUMPER FOR INTERNAL
24 VAC SUPPLY
ES 8 CONNECTED
TO RELAY
T IF NOT
WIRING TO INTERNAL
RELAY 24 VAC SUPPLY
COM
RED
24 VAC
Internal
Supply
24 VAC
NOT
whi
Communication wiring connections, which include a single row
of identified terminal blocks, can be found under a service panel
at the upper back of the machine.
00mA
PHM842N_SVG
Figure 26
58
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
Chemical Injection Using Internal 24VAC Control
Transformer
•
NOTE: Using the Internal 24VAC 300 Milliamp Control
Transformer is recommended by Alliance Laundry Systems.
•
IMPORTANT: DO NOT remove the red jumper wire from
the terminal strip.
There are 3 terminals necessary for this connection option.
Terminal “24VAC COM” is used to connect one side of the
internal control transformer to the external dispenser input
signals common.
The second terminal is used to connect the other side of the
control transformer to the machine output signals common
through a red jumper wire between “24VAC” and “RELAY
COM”. Refer to Figure 27 .
IMPORTANT: Do not use the transformer terminals if
an external power supply is used.
3
2
4
1
5
6
7
= Neutral
= Power
PHM821N_SVG
1.
2.
3.
4.
5.
6.
7.
External Supply Power Output
Internal Control Transformer
RELAY COM Terminal
External Dispenser Input Signal Common
Red Jumper Wire
24VAC Terminal
24VAC COM Terminal
Figure 27
Chemical Injection Using External AC Power Source
NOTE: An External AC Power Source is NOT provided
by Alliance Laundry Systems.
NOTE: Power for external supplies must not be derived
from the high-voltage main power connection point.
1. Remove the red jumper wire installed by the factory between
“24VAC”, and “RELAY COM”.
2. Connect one side of the external power to the “RELAY
COM” and the other to the external dispenser input signals
common. Refer to Figure 28 .
IMPORTANT: The external power must supply power of
240VAC or less and be protected at 3 Amps or less.
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
59
Specifications and Dimensions
3
1
4
2
= Neutral
= Power
5
PHM823N_SVG
1.
2.
3.
4.
5.
External Supply Power Output
Red Jumper Wire
External Supply Input Signal Common
VAC Power Terminal
VAC RETURN Terminal
Figure 28
External Supply Signals
CAUTION
Do not attempt to increase fuse rating or alter wiring
of external chemical supply terminal strip in such as
way that may conflict with the suggested methods
provided on the Optional External Supply Wiring Diagram.
W699
60
Wash-cycle signals are provided to the external chemical supply
equipment and a “wait for the next step” signal can be received
from the supply equipment.
For example, if ES1 is selected the K1 contact will close and
power will be supplied to Supply 1 Signal. The contact will remain closed for the amount of time programmed in control. Refer
to Figure 29 for Internal Supply Connection or Figure 30 for External AC Connection.
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Specifications and Dimensions
3
= Neutral
= Power
1
2
PHM822N_SVG
1. ES1 Power supply
2. K1 Contact
3. Supply 1 Signal
Figure 29
3
= Neutral
= Power
1
2
PHM824N_SVG
1. ES1 Power supply
2. K1 Contact
3. Supply 1 Signal
Figure 30
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
61
Startup
Startup
Basket Rotation
After installation is complete, run the machine through a test cycle and check for a clockwise basket rotation during the extract
step.
1. If rotation is not clockwise, disconnect the power from the
machine.
2. Have a qualified electrician reverse any 2 motor leads.
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
62
Operation
Operation
Operating Instructions for UniLinc Control
1. Verify display shows the Cycle Menu Screen.
2. Press the door unlock button located on the lower left front on
the control. Refer to Figure 31 .
1
PHM705N_SVG
UW35–UW150 Models
1. Emergency Stop Button
PHM717N_SVG
UW150 Models
Figure 31
NOTE: Door must be opened within 5 seconds of
pressing the door unlock button.
3. 35 – 125 models: Turn door handle clockwise and swing the
door left to open. Refer to Figure 32 .
Figure 33
4. Load to capacity whenever possible. DO NOT OVERLOAD.
Underloading can cause out-of-balance conditions that can
shorten machine life.
PHM835N_SVG
Figure 34
PHM791N_SVG
UW35–UW125 Models
Figure 32
CAUTION
Be careful around the open door, particularly
when loading from a level below the door. Impact
with door edges can cause personal injury.
150 models: Turn handle counterclockwise and swing the door
right to open. Refer to Figure 33 .
SW025
NOTE: When washing items which may disintegrate or
fragment, such as mop heads or sponges, use laundry
nets to prevent drain blockage.
IMPORTANT: To prevent out-of-balance conditions,
premature wear or damage to machine when using
laundry nets, use several small nets in a load.
5. Close and lock the door.
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
63
Operation
6. Add dry supplies to the supply dispenser compartment cups
prior to the start of each cycle.
Liquid supplies can be injected directly into the supply dispenser by an external chemical supply system.
NOTE: Supply dispenser compartment cups must
not be removed when an external chemical injection
supply system is attached to the machine.
7. Press
and
keypads to select desired wash cycle.
For Technical Service
Distributor ABC
1-800-555-5555
Cycle41:
Supply Set
Up
Cycle01:
Towels
White
Bleach
PHM706N_SVG
Cycle02:
Towels White
Figure 36
9.
Close door to start cycle or press
keypad to return to
Cycle Menu.
The cycle will continue until its completion. Then the display
will show the door is ready to be unlocked and opened.
Cycle Menu
PHM702N_SVG
NOTE: The drain step that occurs before an extract
step or a spray rinse extract step cannot be skipped
using Rapid Advance. The machine MUST drain and
balance during the drain step before it can extract.
Figure 35
CAUTION
Shakeout Routine
Water cannot be extracted from rubber backed
items. To avoid damage to machine from out of balance conditions, do not use a spin (extract) step
when washing rubber backed items. Warranty will be
voided.
W880
8. Press
to start the selected cycle.
As the cycle proceeds, the display will show a summary of the
cycle occurring.
To begin the cycle at any step other than the first step, press the
keypad to advance through the cycle to the desired starting
point. Refer to Programming Manual for information to disable
Rapid Advance.
If the door is open, the display will indicate that the door needs to
be closed and locked. Refer to Figure 36 .
WARNING
NEVER insert hands or objects into basket until it
has completely stopped. Doing so could result in serious injury.
SW012
A Shakeout agitation step is programmed at the end of every cycle and will help prevent tangling of the load.
The Shakeout time is set at the factory to agitate for 40 seconds.
Refer to Programming Manual to disable or change the time of
the Shakeout.
Basket Jog Feature [150 Pound Model Only]
150 pound models are equipped with a basket jog feature. This
feature allows the basket to rotate very slowly while the door is
open for easy clothes removal. To operate the jog feature:
1. With the door open and the control in Cycle Menu, press and
HOLD both jog buttons. A series of loud beeps will occur, indicating the jog feature is about to start.
64
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Operation
PHM791N_SVG
PHM622N_SVG
Figure 39
Figure 37
The jog feature is deactivated when the loading door is closed
and the jog buttons are not pressed.
4. Load to capacity whenever possible. DO NOT OVERLOAD.
Underloading can cause out-of-balance conditions that can
shorten machine life.
WARNING
To avoid personal injury, do NOT reach into the basket while it is rotating. Keep all personnel at a safe
distance from the machine while using the Basket
Jog Feature.
PHM835N_SVG
W641
Operating Instructions for M30 Control
1. Verify display shows a cycle number.
2. Press the STOP/UNLOCK button located on the control. Refer to Figure 38 .
Figure 40
CAUTION
Be careful around the open door, particularly when
loading from a level below the door. Impact with
door edges can cause personal injury.
SW025
1
NOTE: When washing items which may disintegrate
or fragment, such as mop heads or sponges, use
laundry nets to prevent drain blockage.
PHM758N_SVG
1. Emergency Stop Button
Figure 38
NOTE: The door must be opened within 5 seconds
of pressing the door unlock button.
3. Turn the door handle clockwise and swing the door left to
open it. Refer to Figure 39 .
F8423301ENR3
IMPORTANT: To prevent out-of-balance conditions,
premature wear or damage to machine when using
laundry nets, use several small nets in a load.
5. Close and lock the door.
6. Add dry supplies into the supply dispenser compartment cups
prior to the start of each cycle.
Liquid supplies can be injected directly into supply dispenser
by an external chemical supply system.
NOTE: Supply dispenser compartment cups must
not be removed when an external chemical injection
supply system is attached to the machine.
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
65
Operation
7. Press the numeric keypads to select the desired wash cycle.
Refer to Cycle Number .
Cycle
Number
66
Cycle Name
Cycle
Number
Cycle Name
22
Custom #4
1
Permanent Press Light Soil
23
Custom #5
2
Light Soil
24
Custom #6
3
Permanent Press Medium Soil
25
Custom #7
4
Medium Soil
26
Custom #8
5
Permanent Press Heavy Soil
27
Custom #9
6
Heavy Soil
28
Custom #10
7
Rags
29
Custom #11
8
Reclaim
30
Custom #12
9
Delicates
10
95°C
11
60°C
12
40°C
13
95°C Permanent Press
14
60°C Permanent Press
15
40°C Permanent Press
Table 31
CAUTION
Water cannot be extracted from rubber backed
items. To avoid damage to machine from out of balance conditions, do not use a spin (extract) step
when washing rubber backed items. Warranty will be
voided.
16
70°C Permanent Press
17
50°C Gentle
18
30°C Gentle
19
Custom #1
20
Custom #2
21
Custom #3
W880
8. Press the START keypad to start the selected cycle.
As the cycle proceeds, the display will show and count down the
remaining cycle time.
To begin the cycle at any step other than the first step, press the
START keypad to advance through the cycle to the desired starting point. Refer to the Programming Manual for information to
disable Rapid Advance.
If the door is open, the display will indicate that the door needs to
be closed and locked.
9. Close the door to start a cycle.
The cycle will continue until its completion. Then the display
will show the door is ready to be unlocked and opened.
NOTE: The drain step that occurs before an extract
step or a spray rinse extract step cannot be skipped
using Rapid Advance. The machine MUST drain and
balance during the drain step before it can extract.
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Operation
Shakeout Routine
WARNING
NEVER insert hands or objects into basket until it
has completely stopped. Doing so could result in serious injury.
SW012
A shakeout agitation step is programmed at the end of every cycle and will help prevent tangling of the load.
The shakeout time is set at the factory to agitate for 20 seconds.
Models Equipped with Both Steam and
Electric Heating
1. To switch between the heating type, locate the switch on the
left side of control module. Refer to Figure 41 .
2. To select steam heat, make sure the switch is in the down position.
3. To select electric heat, make sure the switch is in the up position.
PHM784N_SVG
Figure 41
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
67
Maintenance
Maintenance
Maintenance
The following maintenance procedures must be performed regularly at the required intervals.
Routine maintenance maximizes operating efficiency and minimizes downtime. The maintenance procedures described below
will prolong the life of the machine and help prevent accidents.
Daily
WARNING
WARNING
Sharp edges can cause personal injury. Wear safety
glasses and gloves, use proper tools and provide
lighting when handling sheet metal parts.
W366R1
CAUTION
Replace all panels that are removed to perform service and maintenance procedures. Do not operate the
machine with missing guards or with broken or
missing parts. Do not bypass any safety devices.
SW019
Follow local codes for proper advise on laundering infected garments.
On UniLinc Control models, maintenance checklists are also displayed on the control. Press
Menu. Refer to Figure 42 .
to enter Service Schedule
Daily
Weekly
Monthly
Quarterly
Do not spray the machine with water. Short circuiting and serious damage may result.
W782
IMPORTANT: Door lock should be checked daily to ensure proper operation. Also check that all safety and
instruction stickers are on the machine. Any missing or
illegible safety instructions stickers should be replaced
immediately.
Beginning of Day
1. Check door interlock before starting operation:
a. Attempt to start the machine with the door open. The machine should not start.
b. Close the door without locking it and start the machine.
The machine should not start.
c. Attempt to open the door while the cycle is in progress.
The door should not open.
If the door lock and interlock are not functioning properly, disconnect power and call a service technician.
IMPORTANT: Door lock should be checked daily to
ensure proper operation. Also, check that all safety
and instruction stickers are on the machine. Replace as necessary.
2. Inspect water inlet valve hose connections on the back of the
machine for leaks.
3. Inspect steam hose connections for leaks (where applicable).
4. Inspect all chemical inlets, lines and connections for leaks.
WARNING
Service Schedule Menu
PHM707N_SVG
Figure 42
Press
from Cycle Menu to enter Service Menu. The Service Menu provides a user with a time based service reminder list.
The list is broken up into “DAILY”, “WEEKLY”, “MONTHLY”
and “QUARTERLY”.
F8423301ENR3
To reduce the risk of electrical shock, serious injury or death, disconnect the electrical power to
washer-extractor before examining the wiring.
W636
5. Verify that insulation is intact on all external wires and that
all connections are secure. If bare wire is evident, call a service technician.
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
68
Maintenance
End of Day
•
1. Clean the AC drive filter (where applicable):
a. Remove the external plastic cover which contains the filter.
b. Remove the foam filter from the cover.
c. Wash the filter with warm water and allow to air dry. Filter can be vacuumed clean.
•
IMPORTANT: The control module cover and fan filter must be in place for the fan to properly cool the
AC inverter drive. Failure to observe this warning
will void the warranty and could lead to expensive
AC inverter drive repair.
2. Clean the door gasket of residual detergent and all foreign
matter.
3. Clean automatic supply dispenser and lid [where applicable]
inside and out with mild detergent. Rinse with clean water.
4. Clean machine’s top, front, and side panels with mild detergent. Rinse with clean water.
NOTE: Unload the machine promptly after each
completed cycle to prevent moisture buildup. Leave
loading door open at the end of each completed cycle to allow moisture to evaporate.
Weekly
Check the machine for leaks.
a. Start an unloaded cycle to fill the machine.
b. Verify that door and door gasket do not leak.
c. Verify that the drain valve is operating and that the drain
system is free from obstruction. If water does not leak out
during the prewash segment, drain valve is closed and
functioning properly.
•
ISO VG 150 ( 709–871 SUS at 100°F [135–165 cSt at
40°C])
ISO VG 220 ( 1047–1283 SUS at 100°F [198–242 cSt at
40°C])
An SAE 40 rating is also acceptable as long as the cSt or
SUS values are within the specified ranges.
Pump the grease gun slowly, permitting only 2 strokes.
3. Use the following procedures to determine if V-belt requires
replacement or adjustment. Call a qualified service technician
in either case.
a. Check V-belt for uneven wear and frayed edges.
b. After disconnecting power to the machine and removing
all panels necessary for access to the drive belt, use one of
the following methods to verify that the V-belt is properly
tensioned.
• Tension Gauge. Loosen motor mounting bolts and
slide motor along motor plate to change belt span
length. The belt tension should be between 70 and 90
pounds [± 5 pounds] [set initial tension toward the
high end of this range].
• Deflection. Refer to Figure 43 . Loosen motor mounting bolts and slide motor along motor plate to change
belt span length. Belt tension measurements should be
taken as close to the center of the belt span as possible.
For every inch of span length, the belt should deflect
1/64 inch [0.40 mm]. Thus, a belt with span length of
50 inches should deflect 50/64 inch [19.84 mm]. An
initial [run-in] force of 5.25 pounds should be used to
set the belt tension. An operating [normal] force of 3.5
pounds should be used after the machine has been operated for a few hours.
Monthly
NOTE: Disconnect power to the machine at its source
before performing the monthly maintenance procedures.
1. Clean the AC drive fins (where applicable).
2. Each month OR after every 200 hours of operation, lubricate
bearings (locate the bearing lubrication decal at the rear of the
left side of the machine, as viewed from the front).
The grease must have the following characteristics:
•
•
•
•
•
•
NLGI Grade 2
Lithium-based
Water-insoluble
Anti-rusting
Anti-oxidizing
Mechanically stable
2
P044I_SVG
1. Deflection
2. Span Length
Figure 43
The grease must have adequate base oil viscosity with one of the
following ratings:
F8423301ENR3
1
c. Verify that V-belts are properly aligned by checking pulley alignment. Place a straightedge across both pulley
faces. The straightedge should make contact with the pulleys in four places. Refer to Figure 44 .
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
69
Maintenance
•
1
2
3
4
5
P045I_SVG
1.
2.
3.
4.
5.
Drive Motor
Drive Pulley
Belt
Straightedge
Driven Pulley
Figure 44
4. Check overflow hose and drain hose for leaks or visible signs
of deterioration. Replace immediately if either are present.
5. Clean inlet hose filter screens:
a. Turn water off and allow valve to cool, if necessary.
b. Unscrew inlet hose and remove filter screen.
c. Clean with soapy water and reinstall. Replace if worn or
damaged.
6. Tighten anchor bolts, if necessary.
7. Use a vacuum to clean lint from motor.
8. Clean interior of machine, by wiping with a water-soaked
sponge or cloth. Use compressed air to clear debris between
the shell and the basket by directing it through the perforations of the basket.
9. Use compressed air to ensure that all electrical components
are free of moisture and dust.
10. Remove chemical supply components and check all flush hoses and connections for residual chemicals, leaks or visible
signs of deterioration. Clean or replace as necessary.
11. If applicable, check the supply dispenser hoses and hose connections for leaks or visible signs of deterioration. Replace
immediately if either are present.
12. Verify points of contact at terminals and quick disconnects
are firm trhoughout the machine by gently tugging the wires.
Reseat any loose contacts.
If bare metal is showing, paint with primer or solventbased paint.
• If rust appears, remove it with sandpaper or by chemical
means. Then paint with primer or solvent-based paint.
6. Clean steam filter, where applicable.
a. Turn off steam supply and allow time for the valve to
cool.
b. Unscrew nut.
c. Remove element and clean.
d. Replace element and nut.
7. 150 models: place a large magnet over the normally-closed
ball switch to verify the stability switch operation. Refer to
the Verify Safety Switch Operation (For 150 Pound Design 2
Models) section.
Care of Stainless Steel
•
•
•
•
•
•
•
•
Remove dirt and grease with detergent and water. Thoroughly
rinse and dry after washing.
Avoid contact with dissimilar metals to prevent galvanic corrosion when salty or acidic solutions are present.
Do not allow salty or acidic solutions to evaporate and dry on
stainless steel. Wipe clean of any residues.
Rub in the direction of the polish lines or “grain” of the stainless steel to avoid scratch marks when using abrasive cleaners. Use stainless steel wool or soft, non-metal bristle brushes.
Do not use ordinary steel wool or steel brushes.
If the stainless steel appears to be rusting, the source of the
rust may be an iron or steel part not made of stainless steel,
such as a nail or screw.
Remove discoloration or heat tint from overheating by scouring with a powder or by employing special chemical solutions.
Do not leave sterilizing solutions on stainless steel equipment
for prolonged periods of time.
When an external chemical supply is used, ensure no siphoning of chemicals occurs when the machine is not in use. Highly concentrated chemicals can cause severe damage to stainless steel and other components within the machine. Damage
of this kind is not covered by the manufacturer’s warranty.
Locate the pump and tubing below the machines’s injection
point to prevent siphoning of chemicals into the machine.
Quarterly
NOTE: Disconnect power to the machine before performing the quarterly maintenance procedures.
1. Tighten door hinges and fasteners, if necessary.
2. Tighten anchor bolts, if necessary.
3. Tighten motor mounting bolt locknuts and bearing bolt locknuts, if necessary.
4. Verify that the drain motor shield is in place and secure.
5. Check all painted surfaces for bare metal.
70
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
F8423301ENR3
Disposal of Unit
Disposal of Unit
Disposal of Unit
This appliance is marked according to the European directive
2002/96/EC on Waste Electrical and Electronic Equipment
(WEEE).
This symbol on the product or on its packaging indicates that this
product shall not be treated as household waste. Refer to Figure
45 . Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic equipment. Ensuring this product is disposed of correctly will help prevent potential negative consequences for the environment and human
health which could otherwise be caused by inappropriate waste
handling of this product. The recycling of materials will help to
conserve natural resources. For more detailed information about
recycling of this product, please contact the local city office,
household waste disposal service, or the source from which the
product was purchased.
MIX1N_SVG
Figure 45
F8423301ENR3
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
71