PowerLite® Pro Cinema LS9600e
Quick Setup
WirelessHD Transmitter
Follow these steps to set up the included WirelessHD Transmitter.
Before using the projector, make sure you read the safety instructions in the
online User’s Guide.
Turn on your equipment
Adjust the image
1
Turn on your video source.
1Press the Pattern button on the remote control to display a test pattern.
2
Plug in the projector.
Choose a location
Keep the projector level and place it at a height so its lens is even with the top
or bottom of the screen and is centered horizontally. If this isn’t possible, use
the lens shift feature or the keystone correction button on the projector to
reposition the image (see “Adjust the image”).
To raise the image or correct a tilted image, adjust the front feet as
2
HDMI
1Place the transmitter within 32 feet (10 m) of the projector. Make sure the
front of the transmitter faces the front of the projector. See the online
User’s Guide for more information on the WirelessHD transmission range.
shown below.
Press the
3
power button on the projector or the On button on the
remote control. The shutter opens and the power light flashes blue,
then stays on.
In order to view 3D images correctly, RF 3D glasses must be worn within 32 feet
(10 m) of the projector. Use the image below to determine the viewing distance
for 3D projection (the shading represents the 3D viewing area):
Press the Lens button on the remote control and use the
3
and
buttons to focus the image.
Note: To shut down the projector, press the
power button on the
projector or the Standby button on the remote control, then unplug it.
You don’t have to wait for the projector to cool down.
Note: Do not place the transmitter on a metal surface, as this may
interfere with the signal. Make sure there are no obstructions between
the transmitter and the projector.
See the online User’s Guide for more information on where to place your
projector.
2
Plug the AC adapter into the transmitter and a wall outlet.
The default language of the menu system is English. To select another
4
language, press the Menu button on the projector or remote control.
Select Settings and press Enter. Select Language and press Enter. Select
your language and press Enter. Press the Menu button to exit the menu
system.
4Press the Lens button on the remote control again and use the
and
5Press the Lens button on the remote control again and use the
,
buttons to reduce or enlarge the image.
Using the remote control
Connect the projector
Make sure the batteries are installed as shown (two AA batteries).
Choose from the following connections. For additional connection types, see
the online User’s Guide.
Video device
1
Loosen the two screws at the bottom of the cable cover, then pull the
cover forward.
3Connect the HDMI cables to your video input devices and the HDMI ports
on the side and back of the WirelessHD Transmitter. You can connect up
to five input devices to the transmitter. See “Viewing WirelessHD content”
for information on switching between input sources
and
Turn projector on
Choose which source
to display
2Lift the cable cover out of the grooves at the top.
control or the
button on the projector to switch between them.
HDMI cable
Component video cable
RCA video cable
*412630400*
*412630400*
buttons to reposition the image.
Turn projector off
Turn off projector
display
Control connected
sources with
HDMI Link
Note: You can connect tablets, smartphones and other devices that
support the MHL™ standard to the HDMI port on the side of the
WirelessHD Transmitter. Devices that use an MHL connection include
the Samsung™ Galaxy Note™ II and the Roku® Streaming Stick™. Some
devices may require an adapter or may not require an MHL cable.
Not all features or functions may be supported. Check your device’s
documentation for more information.
4To use the transmitter as a pass-through device to a television or other
3Connect up to 4 video devices and use the Source buttons on the remote
,
display, connect an HDMI cable to the display device and the HDMI output
port on the rear of the transmitter. See “Viewing WirelessHD content” for
information on switching between wireless and wired display modes.
Adjust zoom, focus
and lens shift
Switch between
2D and 3D
Navigate projector
menus
Access projector
menus
6If your image looks like
or
, you can use the
button to correct
this.
Control WirelessHD
functions
For more information on using the remote control, see the online
User’s Guide.
Note: Using the keystone adjustment can affect the size and effective
resolution of your image. If possible, change the position of your
projector to eliminate the keystone effect and use the lens shift option
to position the image as necessary.
PowerLite® Pro Cinema LS9600e
Quick Setup
WirelessHD Transmitter
Follow these steps to set up the included WirelessHD Transmitter.
Before using the projector, make sure you read the safety instructions in the
online User’s Guide.
Turn on your equipment
Adjust the image
1
Turn on your video source.
1Press the Pattern button on the remote control to display a test pattern.
2
Plug in the projector.
Choose a location
Keep the projector level and place it at a height so its lens is even with the top
or bottom of the screen and is centered horizontally. If this isn’t possible, use
the lens shift feature or the keystone correction button on the projector to
reposition the image (see “Adjust the image”).
To raise the image or correct a tilted image, adjust the front feet as
2
HDMI
1Place the transmitter within 32 feet (10 m) of the projector. Make sure the
front of the transmitter faces the front of the projector. See the online
User’s Guide for more information on the WirelessHD transmission range.
shown below.
Press the
3
power button on the projector or the On button on the
remote control. The shutter opens and the power light flashes blue,
then stays on.
In order to view 3D images correctly, RF 3D glasses must be worn within 32 feet
(10 m) of the projector. Use the image below to determine the viewing distance
for 3D projection (the shading represents the 3D viewing area):
Press the Lens button on the remote control and use the
3
and
buttons to focus the image.
Note: To shut down the projector, press the
power button on the
projector or the Standby button on the remote control, then unplug it.
You don’t have to wait for the projector to cool down.
Note: Do not place the transmitter on a metal surface, as this may
interfere with the signal. Make sure there are no obstructions between
the transmitter and the projector.
See the online User’s Guide for more information on where to place your
projector.
2
Plug the AC adapter into the transmitter and a wall outlet.
The default language of the menu system is English. To select another
4
language, press the Menu button on the projector or remote control.
Select Settings and press Enter. Select Language and press Enter. Select
your language and press Enter. Press the Menu button to exit the menu
system.
4Press the Lens button on the remote control again and use the
and
5Press the Lens button on the remote control again and use the
,
buttons to reduce or enlarge the image.
Using the remote control
Connect the projector
Make sure the batteries are installed as shown (two AA batteries).
Choose from the following connections. For additional connection types, see
the online User’s Guide.
Video device
1
Loosen the two screws at the bottom of the cable cover, then pull the
cover forward.
3Connect the HDMI cables to your video input devices and the HDMI ports
on the side and back of the WirelessHD Transmitter. You can connect up
to five input devices to the transmitter. See “Viewing WirelessHD content”
for information on switching between input sources
and
Turn projector on
Choose which source
to display
2Lift the cable cover out of the grooves at the top.
control or the
button on the projector to switch between them.
HDMI cable
Component video cable
RCA video cable
*412630400*
*412630400*
buttons to reposition the image.
Turn projector off
Turn off projector
display
Control connected
sources with
HDMI Link
Note: You can connect tablets, smartphones and other devices that
support the MHL™ standard to the HDMI port on the side of the
WirelessHD Transmitter. Devices that use an MHL connection include
the Samsung™ Galaxy Note™ II and the Roku® Streaming Stick™. Some
devices may require an adapter or may not require an MHL cable.
Not all features or functions may be supported. Check your device’s
documentation for more information.
4To use the transmitter as a pass-through device to a television or other
3Connect up to 4 video devices and use the Source buttons on the remote
,
display, connect an HDMI cable to the display device and the HDMI output
port on the rear of the transmitter. See “Viewing WirelessHD content” for
information on switching between wireless and wired display modes.
Adjust zoom, focus
and lens shift
Switch between
2D and 3D
Navigate projector
menus
Access projector
menus
6If your image looks like
or
, you can use the
button to correct
this.
Control WirelessHD
functions
For more information on using the remote control, see the online
User’s Guide.
Note: Using the keystone adjustment can affect the size and effective
resolution of your image. If possible, change the position of your
projector to eliminate the keystone effect and use the lens shift option
to position the image as necessary.
Viewing 3D images
6If you have connected multiple input devices to the transmitter, press
the Input button on the remote control or transmitter once to display
the sub-screen menu, then press the button again to switch between the
input devices.
To view 3D content, you must first connect a 3D-compatible video device to
one of the HDMI ports on your projector.
1
Turn on and begin playback on the 3D-compatible video device.
7
To display two WirelessHD input devices simultaneously, press the P-in-P
button on the bottom of the remote control to enable picture-in-picture
mode. Press and hold the P-in-P button for three seconds to switch the
main image and sub-screen, or press the P-in-P button again to disable
picture-in-picture mode.
Note: Make sure you set the video device to play content in 3D mode.
2
Press the 2D/3D button on the remote control, if necessary.
3Slide the power switch on your 3D glasses to the On position.
See the online User’s Guide for more information on adjusting and configuring
the WirelessHD connection and display modes.
Troubleshooting
If you see a blank screen or the No signal message after turning on your
video device or computer, check the following:
•Make sure the power light on the projector is blue and not flashing.
Note: If the glasses don’t automatically display 3D content, you may
need to pair them with the projector. Move the glasses within 10 feet
(3 m) of the projector, then press and hold the Pairing button on the
3D glasses for at least 3 seconds. The status light on the glasses will
alternately flash green and red, then remain green for 10 seconds if
pairing is successful.
•
Press the
button on the projector or one of the Source buttons on
the remote control to switch to the correct image source, if necessary.
•
If you’re using a Windows laptop, press the function key on your
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it (such as Fn + F7). Wait a moment for the display
to appear.
•
If you’re using a Mac laptop, open System Preferences and select
Displays. Select the VGA Display or Color LCD option if necessary,
then click the Arrange or Arrangement tab, and select the Mirror
Displays checkbox.
See the online User’s Guide for more information on adjusting 3D images.
Viewing WirelessHD
content
1
Turn on your video device and begin playback.
3
Turn on the projector.
4If you have connected a television or other display to the output port on
For more information about using the projector, click the icon on your desktop
to access the online manual (requires an Internet connection). If you don’t have
a User’s Guide icon, you can install it from the projector CD or go to the Epson
website, as described below.
Telephone support services
To use the Epson® PrivateLine® Support service, call (800) 637-7661. This service
is available for the duration of your warranty period. You may also speak with a
support specialist by calling (562) 276-4394 (US) or (905) 709-3839 (Canada).
Support hours are 6 am to 8 pm, Pacific Time, Monday through Friday, and 7 am
to 4 pm, Pacific Time, Saturday. Days and hours of support are subject to change
without notice. Toll or long distance charges may apply.
Internet support
Visit epson.com/support (U.S.) or epson.ca/support (Canada) for solutions to
common problems. You can download utilities and documentation, get FAQs
and troubleshooting advice, or e-mail Epson.
Registration
•
Press the 2D/3D button to switch to 3D viewing mode, if necessary.
•
Make sure that you are within the 3D viewing range. See “Choose a
location” on the front of this sheet or the online User’s Guide for more
information.
•
Check that your 3D glasses have not entered standby mode. Slide the
power switch on the 3D glasses to the Off position, then back to the On
position.
•
Press the Menu button on your remote control, select the Signal menu,
then 3D Setup, then select 3D Format. Make sure that the Auto option
is selected.
•
Check that your video device and media are both 3D-compatible. Refer
to the documentation that came with your video device for more
information.
2Turn on the power switch on the side of the WirelessHD Transmitter.
Manual
®
If 3D images aren’t displaying properly, check the following:
You can also automatically convert 2D HDMI content to 3D. To enable the
2D-to-3D Conversion option, press the Menu button on the projector or
remote control. Select Signal and press Enter, then select 3D Setup and
press Enter. Select 2D-to-3D Conversion and press Enter. Select the Weak,
Medium, or Strong setting, then press Enter.
Where to get help
Register today to get product updates and exclusive offers. You can use the CD
included with your projector or register online at epson.com/webreg.
Optional accessories
For a list of optional accessories, see the online User’s Guide.
You can purchase RF 3D glasses (part number V12H548006) or other
accessories from an Epson authorized reseller. To find the nearest reseller,
call 800-GO-EPSON (800-463-7766). Or you can purchase online at
epsonstore.com (U.S. sales) or epson.ca (Canadian sales).
If WirelessHD content isn’t displaying properly, check the following:
•
the transmitter and want to switch between wired and wireless display
modes, press the Output button on the remote control or transmitter.
The WiHD light on the transmitter lights up when the wireless display
mode is active.
Check that the Link light on the transmitter is lit. If the light is flashing
slowly, the transmitter could not connect with the projector and has
entered standby mode. Verify that the projector is turned on and that all
cables are properly connected as shown in the “WirelessHD Transmitter”
section.
If the Link light continues to flash, press the Input button on the
transmitter and wait 5-10 seconds for the Link light to stay lit. Repeat this
procedure up to five times. If the transmitter still hasn’t connected to the
projector, press the Reset button on the bottom of the transmitter and
try again.
•
5Press the WirelessHD button on the projector remote control.
Note: If the WirelessHD connection fails, see the “Troubleshooting”
section.
•
Make sure the WirelessHD Transmitter is within 32 feet (10 m) of the
projector, isn’t obstructed by any large objects and is not placed on a
metal surface.
If you are viewing wireless content, make sure that the WiHD light on the
transmitter is lit. If it isn’t, press the Output button on the remote control
or transmitter.
EPSON and PowerLite are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of
Seiko Epson Corporation. PrivateLine is a registered trademark of Epson America, Inc.
Mac is a registered trademark of Apple Inc., registered in the US and other countries.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2014 Epson America, Inc., 1/14
Printed in XXXXXX
CPD-40300
Viewing 3D images
6If you have connected multiple input devices to the transmitter, press
the Input button on the remote control or transmitter once to display
the sub-screen menu, then press the button again to switch between the
input devices.
To view 3D content, you must first connect a 3D-compatible video device to
one of the HDMI ports on your projector.
1
Turn on and begin playback on the 3D-compatible video device.
7
To display two WirelessHD input devices simultaneously, press the P-in-P
button on the bottom of the remote control to enable picture-in-picture
mode. Press and hold the P-in-P button for three seconds to switch the
main image and sub-screen, or press the P-in-P button again to disable
picture-in-picture mode.
Note: Make sure you set the video device to play content in 3D mode.
2
Press the 2D/3D button on the remote control, if necessary.
3Slide the power switch on your 3D glasses to the On position.
See the online User’s Guide for more information on adjusting and configuring
the WirelessHD connection and display modes.
Troubleshooting
If you see a blank screen or the No signal message after turning on your
video device or computer, check the following:
•Make sure the power light on the projector is blue and not flashing.
Note: If the glasses don’t automatically display 3D content, you may
need to pair them with the projector. Move the glasses within 10 feet
(3 m) of the projector, then press and hold the Pairing button on the
3D glasses for at least 3 seconds. The status light on the glasses will
alternately flash green and red, then remain green for 10 seconds if
pairing is successful.
•
Press the
button on the projector or one of the Source buttons on
the remote control to switch to the correct image source, if necessary.
•
If you’re using a Windows laptop, press the function key on your
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it (such as Fn + F7). Wait a moment for the display
to appear.
•
If you’re using a Mac laptop, open System Preferences and select
Displays. Select the VGA Display or Color LCD option if necessary,
then click the Arrange or Arrangement tab, and select the Mirror
Displays checkbox.
See the online User’s Guide for more information on adjusting 3D images.
Viewing WirelessHD
content
1
Turn on your video device and begin playback.
3
Turn on the projector.
4If you have connected a television or other display to the output port on
For more information about using the projector, click the icon on your desktop
to access the online manual (requires an Internet connection). If you don’t have
a User’s Guide icon, you can install it from the projector CD or go to the Epson
website, as described below.
Telephone support services
To use the Epson® PrivateLine® Support service, call (800) 637-7661. This service
is available for the duration of your warranty period. You may also speak with a
support specialist by calling (562) 276-4394 (US) or (905) 709-3839 (Canada).
Support hours are 6 am to 8 pm, Pacific Time, Monday through Friday, and 7 am
to 4 pm, Pacific Time, Saturday. Days and hours of support are subject to change
without notice. Toll or long distance charges may apply.
Internet support
Visit epson.com/support (U.S.) or epson.ca/support (Canada) for solutions to
common problems. You can download utilities and documentation, get FAQs
and troubleshooting advice, or e-mail Epson.
Registration
•
Press the 2D/3D button to switch to 3D viewing mode, if necessary.
•
Make sure that you are within the 3D viewing range. See “Choose a
location” on the front of this sheet or the online User’s Guide for more
information.
•
Check that your 3D glasses have not entered standby mode. Slide the
power switch on the 3D glasses to the Off position, then back to the On
position.
•
Press the Menu button on your remote control, select the Signal menu,
then 3D Setup, then select 3D Format. Make sure that the Auto option
is selected.
•
Check that your video device and media are both 3D-compatible. Refer
to the documentation that came with your video device for more
information.
2Turn on the power switch on the side of the WirelessHD Transmitter.
Manual
®
If 3D images aren’t displaying properly, check the following:
You can also automatically convert 2D HDMI content to 3D. To enable the
2D-to-3D Conversion option, press the Menu button on the projector or
remote control. Select Signal and press Enter, then select 3D Setup and
press Enter. Select 2D-to-3D Conversion and press Enter. Select the Weak,
Medium, or Strong setting, then press Enter.
Where to get help
Register today to get product updates and exclusive offers. You can use the CD
included with your projector or register online at epson.com/webreg.
Optional accessories
For a list of optional accessories, see the online User’s Guide.
You can purchase RF 3D glasses (part number V12H548006) or other
accessories from an Epson authorized reseller. To find the nearest reseller,
call 800-GO-EPSON (800-463-7766). Or you can purchase online at
epsonstore.com (U.S. sales) or epson.ca (Canadian sales).
If WirelessHD content isn’t displaying properly, check the following:
•
the transmitter and want to switch between wired and wireless display
modes, press the Output button on the remote control or transmitter.
The WiHD light on the transmitter lights up when the wireless display
mode is active.
Check that the Link light on the transmitter is lit. If the light is flashing
slowly, the transmitter could not connect with the projector and has
entered standby mode. Verify that the projector is turned on and that all
cables are properly connected as shown in the “WirelessHD Transmitter”
section.
If the Link light continues to flash, press the Input button on the
transmitter and wait 5-10 seconds for the Link light to stay lit. Repeat this
procedure up to five times. If the transmitter still hasn’t connected to the
projector, press the Reset button on the bottom of the transmitter and
try again.
•
5Press the WirelessHD button on the projector remote control.
Note: If the WirelessHD connection fails, see the “Troubleshooting”
section.
•
Make sure the WirelessHD Transmitter is within 32 feet (10 m) of the
projector, isn’t obstructed by any large objects and is not placed on a
metal surface.
If you are viewing wireless content, make sure that the WiHD light on the
transmitter is lit. If it isn’t, press the Output button on the remote control
or transmitter.
EPSON and PowerLite are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of
Seiko Epson Corporation. PrivateLine is a registered trademark of Epson America, Inc.
Mac is a registered trademark of Apple Inc., registered in the US and other countries.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2014 Epson America, Inc., 1/14
Printed in XXXXXX
CPD-40300