Marantz | SR4002 | User guide | Marantz SR4002 User guide

Model SR4002/SR5002 User Guide
AV Surround Receiver
SR4002-5002U DFU_00_cover.indd I
07.7.9 2:46:20 PM
IMPORTANT SAFETY
INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
The lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
WARNING
READ BEFORE OPERATING EQUIPMENT
This product was designed and manufactured to
meet strict quality and safety standards. There are,
however, some installation and operation precautions
which you should be particularly aware of.
1.
Read Instr uctions – All the safety and
operating instructions should be read before
the product is operated.
2.
R e t a i n I n s t r u c t i o n s – T h e s a fe t y a n d
operating instructions should be retained for
future reference.
3.
Heed Warnings – All warnings on the product
and in the operating instructions should be
adhered to.
4.
Follow Instructions – All operating and use
instructions should be followed.
5.
Cleaning – Unplug this product from the
wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
6.
Attachments – Do not use attachments not
recommended by the product manufacturer
as they may cause hazards.
7.
Water and Moisture – Do not use this product
near water-for example, near a bath tub,
wash bowl, kitchen sink, or laundry tub, in a
wet basement, or near a swimming pool, and
the like.
8.
Accessories – Do not place this product on
an unstable cart, stand, tripod, bracket, or
table. The product may fall, causing serious
injury to a child or adult, and serious damage
to the product. Use only with a cart, stand,
tripod, bracket, or table recommended by the
manufacturer, or sold with the product. Any
mounting of the product should follow the
manufacturer’s instructions, and should use
a mounting accessory recommended by the
manufacturer.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG
TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE
DE LA PRISE ET POUSSER JUSQU’AU FOND.
NOTE TO CATV SYSTEM INSTALLER:
This reminder is provided to call the CATV (Cable-TV) system installer’s attention to Section 820-40 of the
NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall
be connected to the grounding system of the building, as close to the point of cable entry as practical.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by tuning the
equipment off and on, the user is encouraged to
SR4002-5002U DFU_00_cover.indd II
try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help.
9.
A product and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause the
product and cart combination to overturn.
10.
Ventilation – Slots and openings in the
cabinet are provided for ventilation and to
ensure reliable operation of the product and
to protect it from overheating, and these
openings must not be blocked or covered.
The openings should never be blocked by
placing the product on a bed, sofa, rug, or
other similar surface. This product should not
be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is
provided or the manufacturer’s instructions
have been adhered to.
11.
Power Sources – This product should be
operated only from the type of power source
indicated on the marking label. If you are
not sure of the type of power supply to your
home, consult your product dealer or local
power company. For products intended to
operate from battery power, or other sources,
refer to the operating instructions.
12.
Grounding or Polarization – This product
may be equipped with a polar ized
alternatingcurrent line plug (a plug having
one blade wider than the other). This plug will
fit into the power outlet only one way. This is
a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of
the polarized plug.
NOTE:
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
AC POLARIZED PLUG
07.7.9 2:46:20 PM
13.
14.
15.
16.
17.
18.
Power-Cord Protection – Power-supply cords
should be routed so that they are not likely
to be walked on or pinched by items placed
upon or against them, paying par ticular
attention to cords at plugs, convenience
receptacles, and the point where they exit
from the product.
Protective Attachment Plug – The product
is equipped with an attachment plug having
overload protection. This is a safety feature.
See Instruction Manual for replacement or
resetting of protective device. If replacement
of the plug is required, be sure the service
technician has used a replacement plug
specified by the manufacturer that has the
same overload protection as the original plug.
Outdoor Antenna Grounding – If an outside
antenna or cable system is connected to the
product, be sure the antenna or cable system
is grounded so as to provide some protection
against voltage surges and built-up static
charges. Article 810 of the National Electrical
Code, ANSI/NFPA 70, provides information
with regard to proper grounding of the mast
and suppor ting structure, grounding of
the lead-in wire to an antenna-discharge
unit, size of grounding conductors, location
of antennadischarge unit, connection to
grounding electrodes, and requirements for
the grounding electrode. See Figure 1.
Lightning – For added protection for this
product during a lightning storm, or when it is
left unattended and unused for long periods
of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This
will prevent damage to the product due to
lightning and power-line surges.
Power Lines – An outside antenna system
should not be located in the vicinity of
overhead power lines or other electric light or
power circuits, or where it can fall into such
power lines or circuits. When installing an
outside antenna system, extreme care should
be taken to keep from touching such power
lines or circuits as contact with them might be
fatal.
Overloading – Do not overload wall outlets,
extension cords, or integral convenience
receptacles as this can result in a risk of fire
or electric shock.
19.
Object and Liquid Entry – Never push objects
of any kind into this product through openings
as they may touch dangerous voltage points
or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind
on the product.
20.
Servicing – Do not attempt to service this
product yourself as opening or removing
covers may expose you to dangerous voltage
or other hazards. Refer all ser vicing to
qualified service personnel.
21.
Damage Requiring Service – Unplug
this product from the wall outlet and refer
servicing to qualified service personnel under
the following conditions:
a.
When the power-supply cord or plug is
damaged.
b.
If liquid has been spilled, or objects have
fallen into the product.
c.
If the product has been exposed to rain or
water.
d.
If the product does not operate normally by
following the operating instructions. Adjust
only those controls that are covered by
the operating instructions as an improper
adjustment of other controls may result in
damage and will often require extensive
work by a qualified technician to restore the
product to its normal operation.
e.
If the product has been dropped or damaged
in any way, and
f.
When the product exhibits a distinct change
in performance this indicates a need for
service.
22.
Replacement Parts – When replacement
par ts are required, be sure the ser vice
technician has used replacement par ts
specified by the manufacturer or have the
same characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock, or other hazards.
23.
Safety Check – Upon completion of any
service or repairs to this product, ask the
service technician to perform safety checks
to determine that the product is in proper
operating condition.
24.Wall or Ceiling Mounting – The product should
be mounted to a wall or ceiling only as
recommended by the manufacturer.
25.
Heat – The product should be situated away
from heat sources such as radiators, heat
registers, stoves, or other products (including
amplifiers) that produce heat.
FIGURE 1
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
GROUND CLAMPS
NEC - NATIONAL ELECTRICAL CODE
This Class B digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la Classe B est conforme
à la norme NMB-003 du Canada.
DECLARATION OF CONFORMITY
This device complies with Part 15 of the FCC rules. Operation is subject to the
following conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
U.S. Responsible Party:
Marantz America, Inc.
100 Corporate Drive,
Mahwah, NJ, 07430, U.S.A.
TEL: 630-741-0300
Type of Product:
AV Surround Receiver
Model:
SR4002/SR5002
AV_060908U1
SR4002-5002U DFU_00_cover.indd III
07.7.9 3:01:58 PM
TABLE OF CONTENTS
Thank you for purchasing the Marantz SR4002/SR5002 Surround receiver.
This remarkable component has been engineered to provide you with many years of home theater enjoyment.
Please take a few minutes to read this manual thoroughly before you connect and operate the SR4002/
SR5002.
As there are a number of connection and configuration options, you are encouraged to discuss your own
particular home theater setup with your Marantz A/V specialist dealer.
INTRODUCTION ....................................1
BASIC OPERATION (PLAYBACK)......34
ACCESSORIES CHECK ....................................................1
SELECTING AN INPUT SOURCE ...................................34
SELECTING THE SURROUND MODE...........................34
NIGHT MODE ..................................................................34
ADJUSTING THE MAIN VOLUME ..................................34
ADJUSTING THE TONE (BASS & TREBLE) CONTROL...34
TEMPORARILY TURNING OFF THE SOUND ..................34
USING THE SLEEP TIMER .............................................34
VIDEO CONVERT ............................................................35
TABLE OF CONTENTS .........................1
FEATURES .............................................2
DESCRIPTION ...................................................................2
BEFORE USE.........................................4
ACCESSORIES CHECK
OPERATION OF REMOTE CONTROLLER ......................4
Before use, check the below accessories were included in the package.
Remote Controller
AM Loop Antenna
N
AR
LE
SO
URCE
l/
ND
SE
LA
Y
ON
DI
P.
REC
T
RTU
EO
BAN
D
AL
ER
ST
VI
H
1C
IN
4
GHT
NI
7.
D
A/
4
s
dt
ST
B
A/
P.S
CA
T.M
SURR
LIP
INP SYNC
UT /
OU
FM Antenna
ND
OD
E
N
HT-EQ
ME
MO
AT
I/C
E
UT
M
ULT
M
E
UM
LL
VO
R
PK
-S
M
NE
U
EN
M
R
SP
H
KR
SP
TO
TE
S
/E
AT
/C
CH
T.
EN
EX
-C
M
L
D
SETU
P/
3
6
9
+10
OFF
DI
P
AIT
C
OS
2
II
5
8
0
T
SE
P
EE
SL
1
CS
4
7
AC Power Cable
SS
BA
T.D
ISP
ET
ES
PR
PTY
F.D
IRE
GLE
NG
NI
TU
AN
V-O
FRONT PANEL (SR4002) ..................................................5
FRONT PANEL (SR5002) ..................................................5
FL DISPLAY AND INDICATOR ..........................................7
REAR PANEL (SR4002).....................................................8
REAR PANEL (SR5002).....................................................8
REMOTE CONTROLLER ................................................10
IT
EX
+
SC
DI
CH-SE
L
NAMES AND FUNCTIONS ....................5
SUBT
ITL
E
ATT.
AU
DIO
D
R
NE
TU
SS V
BA D
TV
FF
CT
V
CD
PE
TA
C
R
TREB
LE
D
S
1
R
CD
X
AU
S
SY
MD
2
M
X
AU
STE
P
AM
NTR
CO
TE R
O S
M 00
RE C55
R
O
LL
ER
AAA-size batteries × 2
Warranty Card
USA × 1
Canada × 1
REMOTE CONTROL OPERATION .....12
GENERAL INFORMATION OF REMOTE CONTROLLER
TO THE UNIT ...................................................................12
CONTROLLING MARANTZ COMPONENTS .................13
BASIC OPERATION .........................................................16
CONNECTIONS ...................................18
Microphone MC-10
Front AUX Jack Cover
P
PU
US
SH
H
User Guide
SPEAKER PLACEMENT .................................................18
CONNECTING SPEAKERS.............................................18
CONNECTING AUDIO COMPONENTS..........................19
CONNECTING VIDEO COMPONENTS..........................20
CONNECTING HDMI COMPONENTS............................21
ADVANCED CONNECTING ............................................22
CONNECTING THE REMOTE CONTROL JACKS.........22
CONNECTING THE ANTENNA TERMINALS .................23
XM RADIO OVERVIEW (SR5002 ONLY) ........................24
CONNECTING THE XM CONNECT-AND-PLAY ANTENNA...24
CONNECTING FOR THE MULTI ROOM (SR5002 only) 25
CONNECTING OTHER EQUIPMENT.............................26
SETUP ..................................................27
ON SCREEN DISPLAY MENU SYSTEM ........................27
1 INPUT SETUP (ASSIGNABLE DIGITAL INPUT AND
COMPONENT VIDEO INPUT).........................................28
2 SPEAKER SETUP........................................................28
3 PREFERENCE .............................................................31
4 SURROUND .................................................................31
5 PL II (PRO LOGIC II) MUSIC PARAMETER ..............32
6 CS II (CIRCLE SURROUND II) PARAMETER ...........32
7 7.1 CH INPUT LEVEL...................................................32
8 MULTI ROOM (SR5002 only).......................................32
SIMPLE SETUP....................................33
ENGLISH
INTRODUCTION
SURROUND MODE .............................36
OTHER FUNCTION ..............................39
DISPLAY MODE ...............................................................39
RECORDING AN ANALOG SOURCE .............................39
SELECTING ANALOG AUDIO INPUT OR DIGITAL AUDIO
INPUT ..............................................................................39
LISTENING THROUGH HEADPHONES .........................40
DOLBY HEADPHONE MODE .........................................40
ATTENUATION TO ANALOG INPUT SIGNAL ................40
SPEAKER A/B ..................................................................40
7.1 CH INPUT ...................................................................40
AUX2 INPUT.....................................................................41
HT-EQ (HOME THEATER EQUALIZER) .........................41
TV AUTO ON/OFF FUNCTION........................................41
VIDEO ON/OFF ...............................................................41
LIP.SYNC (SR5002 only)..................................................41
BASIC OPERATION (TUNER).............42
LISTENING TO THE TUNER ...........................................42
PRESET MEMORY ..........................................................42
LISTENING TO XM SATELLITE RADIO (SR5002 ONLY)....44
SEARCH MODE ...............................................................45
PRESET MEMORY ..........................................................47
MULTI ROOM SYSTEM (SR5002 ONLY) ...48
MULTI ROOM PLAYBACK USING THE MULTI ROOM
OUT TERMINALS.............................................................48
MULTI ROOM PLAYBACK USING THE MULTI SPEAKER
TERMINALS .....................................................................48
SURROUND SPEAKER B SYSTEM (SR4002 ONLY) .49
ANOTHER ROOM PLAYBACK USING THE S
(SURROUND) SPEAKER B TERMINALS.......................49
TROUBLESHOOTING .........................50
HDMI .................................................................................51
XM SATELLITE RADIO ....................................................52
TECHNICAL SPECIFICATIONS ..........53
SETUP CODES .......................................I
1
SR4002-5002U DFU_01_E1_2.indd 1
07.7.9 2:46:43 PM
ENGLISH
FEATURES
An easy-to-use universal remote controller allows full
access to all of the operating functions and can be
used for system operation as well.
This unit incorporates the latest generation of digital
surround sound decoding technology such as Dolby
Digital EX, Dolby Digital, DTS-ES (Discrete 6.1 and
Matrix 6.1), DTS Neo:6 (Cinema, Music), Dolby ProLogic IIx (Movie, Music and Game), Circle Surround
II (Cinema and Music).
In addition, Marantz has focused on the future. By
utilizing pre-out jacks, 7.1 direct inputs and a RS232C communication port (SR5002 only), the unit is
tomorrow’s technology, today!
This unit has Simple Setup function for easy setup.
You can setup all speaker settings by just selecting
your room size and the number of your speakers with
Simple Setup function.You can also setup customized
settings just like conventional AV amplifiers.
This unit features a fully discrete 7 channel amplifier
section capable of delivering 80 watts (SR4002)/90
watts (SR5002) of high-current amplification, for
continuously clean and stable power into each of the 7
channels. It employs a massive EI power transformer
in combination with oversized filter capacitors.
This design configuration is capable of a clear and
powerful reproduction of the most demanding action
movie soundtracks and full range (multichannel)
music discs. Through its ability to generate very high
output voltages, the unit can easily drive the most
demanding speakers with optimum results.
This unit incorporates the most advanced Digital
Signal Processing circuitry, along with a Crystal® 192
kHz/24 bit D/A converter in each of the 7 channels.
Independent power supply circuits are incorporated for
the FL display, audio and video sections for maximum
separation, clarity and dynamic range. Together with
hand-selected customized components, all elements
work in harmony to recreate the emotion, exactly as
the artist had intended.
This unit is designed and engineered with extensive
feedback from custom installation experts, dealers
and consumers. It features multi-room/multisource,
a RS-232C communication port (SR5002 only),
heavy duty speaker binding posts and an extensive
array of both analog and digital inputs / outputs.
With 6 assignable digital inputs (including Front
Aux), 3 assingnable component inputs (SR5002),
5 assignable digital input (SR4002), Super Audio
CD Multi Channel (7.1 channel) direct inputs video
convert system and OSD output versatility is taken
to a stunning new level. Furthermore, the unit can
output the OSD information through the Y/C (Svideo) and composite video outputs.
• Dolby Digital EX, Dolby Digital ,
DTS ES (Discrete 6.1, Matrix 6.1, Neo: 6)
• Dolby Headphone 2
• Dolby Pro Logic IIx (Movie, Music, Game)
• Circle Surround II (Movie, Music, Mono)
• HDCD decording
• MRAC (Marantz Room Acoustic Calibration)
available
• Simple Setup Function
• Improved Station Name Input Method, 50 Presets
• Auto Adjust Function for Speaker Distance Settings
(Delay Time)
• LIP.SYNC Funciton (Audio delay)
• 7 × 80 Watts (8 Ohm) (SR4002)/7 × 90 Watts (8
Ohm) (SR5002), Discrete Amplifiers
• High Power Current Feedback Circuitry
• Massive Energy Power Supply, Huge EI
Transformer, Large ELCO’s.
• 192 kHz/24 bit Crystal® DAC for all 8 Channels
• 32 bit Digital Surround Processing Chipsets
• Large Heavy Duty Speaker Terminals for all
Channels
• Auto Input Signal Detection
• Front AUX Input (Digital Camera, Portable DVD)
• Video Off Mode
• Set Up Menu via all Video Output (Composite, SVideo and Component video)
• Video convert system
• RS-232C Terminal for System Control (SR5002only)
• Universal remote control
• HDMI (Ver. 1.1)
3 Input/1 Output (SR5002)
2 Input/1 Output (SR4002)
DESCRIPTION
Manufactured under license under U.S. Patent
#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,226,616; 6,487,535; 7,003,467 & other U.S. and
worldwide patents issued & pending. DTS, DTS
Digital Surround, ES, and Neo:6 are registered
trademarks and the DTS logos, Symbol and DTS
96/24 are trademarks of DTS, Inc. © 1996-2007 DTS,
Inc. All Rights Reserved.
• dts Digital Surround
DTS was introduced in 1994 to provide 5.1 channels of
discrete digital audio into home theater systems.
DTS brings you premium quality discrete multichannel
digital sound to both movies and music.
DTS is a multichannel sound system designed to
create full range digital sound reproduction.
The no compromise DTS digital process sets the
standard of quality for cinema sound by delivering
an exact copy of the studio master recordings to
neighborhood and home theaters.
Now, every moviegoer can hear the sound exactly as
the moviemaker intended.
DTS can be enjoyed in the home for either movies or
music on of DVD’s, LD’s, and CD’s.
• dts Neo:6
The advantages of discrete multichannel systems
over matrix are well known.
But even in homes equipped for discrete multichannel,
there remains a need for high-quality matrix decoding.
This is because of the large library of matrix surround
motion pictures available on disc and on VHS tape; and
analog television broadcasts.
The typical matrix decoder of today derives a center
channel and a mono surround channel from twochannel matrix stereo material. It is better than a
simple matrix in that it includes steering logic to
improve separation, but because of its mono, bandlimited surround it can be disappointing to users
accustomed to discrete multichannel.
Neo:6 offers several important improvements as
follow,
• Neo:6 provides up to six full-band channels of
matrix decoding from stereo matrix material. Users
with 6.1 and 5.1 systems will derive six and five
separate channels, respectively, corresponding to
the standard home-theater speaker layouts.
• Neo:6 technology allows various sound elements
within a channel or channels to be steered
separately, and in a way which follows naturally
from the original presentation.
• Neo:6 offers a music mode to expand stereo nonmatrix
recordings into the five- or six-channel layout, in a way
which does not diminish the subtlety and integrity of
the original stereo recording.
• dts Digital Surround ES
DTS-ES Extended Surround is a new multichannel
digital signal format developed by Digital Theater
Systems Inc. While offering high compatibility with the
conventional DTS Digital Surround format, DTS-ES
Extended Surround greatly improves the 360-degree
surround impression and space expression thanks
to further expanded surround signals. This format
has been used professionally in movie theaters since
1999.
In addition to the 5.1 surround channels (FL, FR, C,
SL, SR and LFE), DTS-ES Extended Surround also
offers the SB (Surround Back) channel for surround
playback with a total of 6.1 channels. DTS-ES
Extended Surround includes two signal formats with
different surround signal recording methods, as DTSES Discrete 6.1 and DTS-ES Matrix 6.1.
• dts Digital Surround 96/24
The stereo CD is a 16-bit medium with sampling at
44.1 kHz. Professional audio has been 20- or 24bit for some time, and there is increasing interest
in higher sampling rates both for recording and for
delivery into the home. Greater bit depths provide
extended dynamic range. Higher sampling rates
allow wider frequency response and the use of antialias and reconstruction filters with more favorable
aural characteristics.
DTS 96/24 allows for 5.1channel sound tracks to be
encoded at a rate of 96kHz/24bits on DVD-Video
titles.
When DVD-video appeared, it became possible to
deliver 24-bit, 96 kHz audio into the home, but only in
two channels, and with serious limitations on picture.
This capability has had little use.
DVD-audio allows 96/24 in six channels, but a
new player is needed, and only analog outputs are
provided, necessitating the use of the D/A converters
and analog electronics provided in the player.
DTS 96/24 offers the following:
1. Sound quality transparent to the original 96/24
master.
2
SR4002-5002U DFU_01_E1_2.indd 2
07.7.9 2:46:44 PM
Dolby Pro Logic IIx is fully compatible with Dolby
Surround Pro Logic technology and can optimally
decode the thousands of commercially available
Dolby Surround encoded video cassettes and
television programs with enhanced depth and
spatiality. It can also process any high-quality
stereo or Advanced Resolution 5.1-channel music
content into a seamless 6.1- or 7.1-channel listening
experience.
CS-II is packed with other useful feature like dialog
clarity (SRS Dialog) for movies and cinema-like bass
enrichment (TruBass). CS-II can enable the dialog
to become clearer and more discernable in movies
and it enables the bass frequencies contained in
the original programming to more closely achieve
low frequencies – overcoming the low frequency
limitations of the speakers by full octave.
Circle Surround II, Dialog Clarity, TruBass, SRS and
symbol are trademarks of SRS Labs, Inc.
Circle Surround II, Dialog Clarity and TruBass
technology are incorporated under license from SRS
Labs, Inc.
Dolby Digital identifies the use of Dolby Digital audio
coding for such consumer formats as DVD and DTV.
As with film sound, Dolby Digital can provide up
to five full-range channels for left, center, and right
screen channels, independent left and right surround
channels, and a sixth (“.1”) channel for low-frequency
effects.
Dolby Surround Pro Logic II is an improved matrix
decoding technology that provides better spatiality
and directionality on Dolby Surround program
material; provides a convincing three-dimensional
soundfield on conventional stereo music recordings;
and is ideally suited to bring the surround experience
to automotive sound. While conventional surround
programming is fully compatible with Dolby Surround
Pro Logic II decoders, soundtracks will be able to be
encoded specifically to take full advantage of Pro
Logic II playback, including separate left and right
surround channels. (Such material is also compatible
with conventional Pro Logic decoders.)
Dolby Digital EX creates six full-bandwidth output
channels from 5.1-channel sources. This is done
using a matrix decoder that derives three surround
channels from the two in the original recording. For
best results, Dolby Digital EX should be used with
movies soundtracks recorded with Dolby Digital
Surround EX.
About Dolby Pro Logic IIx
Dolby Pro Logic IIx technology delivers a natural
and immersing 7.1-channel listening experience
to the home theater environment. A product of
Dolby’s expertise in surround sound and matrix
decoding technologies, Dolby Pro Logic IIx is a
complete surround sound solution that maximizes
the entertainment experience from stereo as well as
5.1-channel encoded sources.
The Dolby Headphone technology provides a
surround sound listening experience over headphones.
When listening to multichannel content such as DVD
movies over headphones, the listening experience
is fundamentally different than listening to speakers.
Since the headphone speaker drivers are covering
the pinna of the ear, the listening experience differs
greatly from traditional speaker playback. Dolby
utilizes patented headphone perspective curves to
solve this problem and provides a non-fatiguing,
immersive, home theater listening experience. Dolby
Headphone also delivers exceptional 3D audio from
stereo material.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are
trademarks of Dolby Laboratories.
Circle Surround II (CS-II) is a powerful and versatile
multichannel technology. CS-II is designed to enable
up to 6.1 multichannel surround sound playback
from mono, stereo, CS encoded sources and other
matrix encoded sources. In all cases the decoder
extends it into 6 channels of surround audio and a
LFE/subwoofer signal. The CS-II decoder creates a
listening environment that places the listener “inside”
music performances and dramatically improves
both hi-fi audio conventional surround-encoded
video material. CS-II provides composite stereo rear
channels to greatly improve separation and image
positioning – adding a heightened sense of realism
to both audio and A/V productions.
XM Satellite Radio Ready
ENGLISH
2. Full backward compatibility with all existing
decoders. (Existing decoders will output a 48 kHz
signal)
3. No new player required: DTS 96/24 can be carried
on DVD-video, or in the video zone of DVD-audio,
accessible to all DVD players.
4. 96/24 5.1-channel sound with full-quality fullmotion video, for music programs and motion
picture soundtracks on DVD-video.
The XM name and related logos are registered
trademarks of XM Satellite Radio Inc.
HDCD® (High Definition Compatible Digital ®) is a
patented process for delivering on Compact Disc the
full richness and details of the original microphone
feed.
HDCD encoded CDs sound better because they are
encoded with 20-bits of real musical information as
compared to 16-bits for all other CDs.
HDCD overcomes the limitation of the 16-bit CD
format by using a sophisticated system to encode
the additional four bits onto the CD while remaining
completely compatible with the CD format.
When listening to HDCD recordings, you hear more
dynamic range, a focused 3-D sound stage, and
extremely natural vocal and musical timbre. With
HDCD, you get the body, depth and emotion of the
original performance not a flat, digital imitation.
HDCD system manufactured under license from
Microsoft. This product is covered by one or more
of the following: In the United States 5,479,168
5,638,074 5,640,161 5,808,574 5,838,274 5,854,600
5,864,311 5,872,531 and in Australia 669,114 with
other patents pending.
HDMI, the
and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
3
SR4002-5002U DFU_01_E1_2.indd 3
07.7.9 2:46:45 PM
ENGLISH
BEFORE USE
This section must be read before any connection is
made to the mains supply.
EQUIPMENT MAINS WORKING SETTING
Your Marantz product has been prepared to comply
with the household power and safety requirements
that exist in your area.
SR4002/SR5002 can be powered by 120V AC only.
KEEP OBJECTS OFF
LOADING BATTERIES
CAUTIONS ON BATTERIES
Keep objects off the unit. Blocking the vent can result
in accident and damage.
Before using the remote controller for the first time,
load the batteries in the remote controller. The
batteries provided are used to verify the operations
of the remote controller only.
• Use “AAA” type batteries in this remote controller.
• We recommend that you use alkali batteries.
• If the remote controller does not operate from
close to the unit, replace the batteries with new
ones, even if less then a year has passed.
• The included battery is only for verifying operation.
Replace it with a new battery as soon as possible.
• When inserting the batteries, be careful to do so in
the proper direction, following the + and - marks in
the remote controller’s battery compartment.
• To prevent damage or battery fluid leakage:
- Do not use a new battery with an old one.
- Do not use two different types of batteries.
- Do not short-circuit, disassemble, heat or
dispose of batteries in flames.
• Remove the batteries when not planning to use the
remote controller for a long period of time.
• If the batteries should leak, carefully wipe off the
fluid from the inside of the battery compartment,
then insert new batteries.
• When disposing of used batteries, please comply
with governmental regulations or environmental
public instruction’s rules that apply in your country
or area.
DO NOT TOUCH HOT SPOTS DURING AND
IMMEDIATELY AFTER USE
During and immediately after use, the unit is hot
in areas other than the controls and rear panel
connection jacks. Do not touch hot spots and
especially the top panel. Contact with hot areas can
cause burns.
1.
Remove the battery cover.
2.
Load the two new size “AAA” batteries inside
the battery compartment while taking care to
align their polarities correctly with the polarity
markings ( with ( and
with ).
3.
Close the battery cover until it clicks shut.
COPYRIGHT
Recording and playback of any material may
require consent. For further information refer to the
following:
—
—
—
—
Copyright Act 1956
Dramatic and Musical Performers Act 1958
Performers Protection Acts 1963 and 1972
Any subsequent statutory enactments and
orders
OPERATION OF REMOTE CONTROLLER
REMOTE CONTROL
Operate the remote controller within a distance of
approx. 5m from the infrared receptor window on the
front of the unit.
DO NOT LOCATE IN THE FOLLOWING PLACES
To ensure long-lasting use, do not locate the unit where:
• Exposed to direct sunlight.
• Near to sources of heat such as heaters.
• Highly humid or poorly ventilated.
• Dusty.
• Subjected to mechanical vibrations.
• On wobbly, inclined or otherwise unstable
surfaces
• Radiated heat is blocked such as in cramped
audio racks.
To ensure proper heat radiation, ensure the below
clearance from walls and other equipment.
8 ins. (0.2 m)
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
VOLUME
8 ins. (0.2 m)
8 ins. (0.2 m)
DOWN
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
MEMORY
UP
CLEAR
ATT
ENTER
AUTO
POWER ON/STANDBY
DISPLAY
MUTE
STANDBY
SETUP MIC
PHONES
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
8 ins. (0.2 m)
5
ox.
ppr
m
INPUT
SELEC
AV
TOR
SURRO
UND
RECEIV
ER
SR5002
MULT
I
STANDBY
POWER
M.
ON/OF
A
SPEAK
ER
F
B
SETUP
MIC
SURRO
MODE
UND
PHONE
S
PURE
DIREC
T
SIMPL
SETUP
E
AUTO
HT-EQ
MENU
VOLUM
E
DISPL
ENTER
AY
MEMO
RY
DOWN
CLEAR
EXIT
BAND
T-MOD
E
MUTE
UP
DIGITA
L
7.1CH
INPUT
S-VIDE
O
AUX
VIDEO 1
INPUT
L
AUDIO
R
60°
SYSTEM
REMOT
RC5500 E
CONTR
SR
OLLER
SR4002/SR5002
Remote controller
Caution:
• Do not allow direct sunlight, an inverter fluorescent
light or other strong source of light to shine onto
the player’s infrared receptor window. Otherwise,
the operation of the remote controller may be
disabled.
• Bear in mind that operating the remote controller
may cause other devices operated by infrared rays
to be operated by mistake.
• The remote controller cannot be operated if the
space between the controller and the player’s
infrared receptor window is obstructed.
• Do not place any objects on top of the remote
controller.
Doing so may cause one or more buttons to be
held down which will cause the batteries to run
down.
4
SR4002-5002U DFU_01_E1_2.indd 4
07.7.9 2:46:45 PM
When this switch is pressed once, the unit turns ON
and the display illuminates. When pressed again, the
unit turns OFF and the STANDBY indicator will be
illuminated.
FRONT PANEL (SR4002)
qw e
rt y u i o
!0 !1
!2
!3
!4
w
VOLUME
DISP
SLEEP
MULTI
AUTO
AUTO SURR
TUNED
DIRECT
ST
V – OFF
DISC 6.1
NIGHT
MTX 6.1
PEAK
ATT
ANALOG
SPKR B
EQ
DIGITAL
L
S
DOWN
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
MEMORY
UP
MUTE
ATT
AUTO
SETUP MIC
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
PHONES
@4
@3 @2 @1 @0 !9 !8 !7 !6
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
e
R
!5
FRONT PANEL (SR5002)
qw e
rt y u i o
!0 !1
!2
!3
!4
INPUT SELECTOR
VOLUME
DISP
SLEEP
MULTI
AUTO
AUTO SURR
TUNED
DIRECT
ST
V – OFF
DISC 6.1
NIGHT
MTX 6.1
PEAK
ATT
ANALOG
SPKR B
EQ
DIGITAL
SURROUND
L
R
C
LFE
SL
S
SURROUND
MODE
MULTI
PURE
DIRECT
SIMPLE
SETUP
MEMORY
CLEAR
ATT
ENTER
AUTO
SETUP MIC
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
PHONES
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
!0
@3 @2 @1 @0 !9 !8 !7 !6
!5
S.(Surround) SPEAKER B button
(SR4002 only)
HEADPHONE jack for stereo
headphones
This jack may be used to listen to the unit’s output
through a pair of headphones. Be certain that the
headphones have a standard 1 / 4” stereo phono
plug.
y
@4
SIMPLE SETUP button
r
UP
MUTE
STANDBY
POWER ON/STANDBY
DISPLAY
MULTI SPEAKER
M.(Multi Room) SPEAKER button
(SR5002 only)
Press this button to activate the Multiroom Speaker
system. “MULTI” indicator will be illuminated in the
display. (See page 44)
SR
DOWN
When this button is pressed once, “SOURCE DIRECT”
appears on the FL display. If pressed again, “PURE
DIRECT” appears. After 2 seconds, the FL display
indication goes out.
In the source/pure direct mode, the tone control
circuitry and bass management are bypassed.
Press this button to enter the simple setup mode.
You can setup the speaker conditions (speaker sizes,
number of speakers, speaker delay times) quickly by
pressing the cursor buttons.
t
DIGITAL
PCM
INPUT SELECTOR knob
(AUDIO/ VIDEO)
Press this button to activate the Surround Speaker B
system . “SPKR B” indicator will be illuminated in the
display. (See page 45)
AV SURROUND RECEIVER SR5002
PURE DIRECT button and
indicator
o
ENTER
POWER ON/STANDBY
i
r
7.1CH INPUT button (SR4002 only)
Press this button to select the output of an external
multichannel player.
CLEAR
S.SPEAKER B
STANDBY
w
SR
SURROUND MODE button
Press this button to select the surround mode.
This knob is used to select the input sources. (See
page 33)
R
C
LFE
SL
u
Notes:
• The surround mode is automatically switched to
AUTO when the pure direct/source direct function
is turned on.
• Additionally, speaker configurations are fixed
automatically as follows.
Front SPKR = LARGE
Center SPKR = LARGE
Surround SPKR = LARGE
Surround Back SPKR = LARGE
Sub woofer = YES
SURROUND
DIGITAL
PCM
SURROUND
MODE
MULTI (Multi Room) button
(SR5002 only)
Press this button to activate the Multiroom system.
“MULTI” indicator will be illuminated in the display.
AV SURROUND RECEIVER SR4002
INPUT SELECTOR
7.1 CH INPUT
POWER switch and STANDBY
indicator
INFRARED receiving sensor
window
This window receives infrared signals for the remote
control.
ENGLISH
q
NAMES AND FUNCTIONS
DISPLAY button
Press this button to change the FL display mode.
(See page 38)
!1
MEMORY button
Press this button to enter the tuner preset memory
numbers or station names. (See page 41)
!2
CLEAR button
Press this button to cancel the station-memory
setting mode or preset scan tuning. (See page 42)
!3
VOLUME control knob
This knob is used to adjust the overall sound level.
Turning the control clockwise increases the sound
level. (See page 33)
5
SR4002-5002U DFU_01_E1_2.indd 5
07.7.9 2:46:46 PM
ENGLISH
!4
ATT (Attenuate) button
@1
MENU button
Press this button to reduce the analog audio signal
input level by about half. “ATT” indicator will be
illuminated in the display. (See page 39)
Press this button to enter the SETUP MAIN MANU.
!5
Press this button to turn on or off HT(Home Theater)EQ mode. This mode compensates for the audio
portion of a movie sounding “bright”. “EQ” indicator
will be illuminated in the display. (See page 40)
AUX1 INPUT jacks
These auxiliary video/audio input jacks accept the
connections of a camcorder, portable DVD, game etc.
When not using these jacks, protect with the included
jack covers.
How to Attach the Front AUX Jack Cover
BA
ND
T-
M
OD
E
M
UTE
DIG
UP
ITA
L
7.
1C
H
@2
@3
HT-EQ button
AUTO (Auto surround) button
Press this button to select the AUTO mode from the
surround modes. When this mode is selected, the unit
determines the surround mode corresponding to a
digital input signal automatically.
IN
PU
S-V
ID
EO
T
@4
AU
VID X 1
EO INP
UT
L
SETUP MIC jack
AU
DIO
R
P
PU
US
SH
H
Automatically measure speaker characteristics using
the included microphone (MC-10). (See page 29)
Front AUX Jack Cover
!6
MUTE button
Press this button to mute the output to the speakers.
Press it again to return to the previous volume level.
!7
T-MODE button
Press this button to select the auto stereo mode or
mono mode when the FM band is selected.
“AUTO” indicator will be illuminated in the display.
(See page 41)
!8
BAND button
Press this button to switch between FM and AM in
the TUNER mode.
!9
EXIT button
Press this button to exit from the SETUP MAIN
MENU.
@0
Cursor (1, 2, 3, 4) / ENTER button
Press these buttons to operate the SETUP MAIN
MENU and TUNER function.
6
SR4002-5002U DFU_01_E1_2.indd 6
07.7.9 2:46:46 PM
s
a
DISP
™0
SLEEP
f
g
d
MULTI
h
AUTO
AUTO SURR
TUNED
DIRECT
j
ST
V – OFF
DISC 6.1
k ¡0 ¡2
¡4
l ¡1 ¡3
PEAK
ATT
ANALOG
SURROUND
SPKR B
EQ
DIGITAL
DIGITAL
NIGHT
MT X 6.1
¡5
L
SL
¡9
a
DISP (Display Off) indicator
¡8
j
C
S
¡7
¡6
V (video)-OFF mode indicator
s
k
d
Multi-room system indicator
This indicator is illuminated when the multi-room
system is active.
f
AUTO SURR (Auto Surround
mode) indicator
This indicator is illuminated to show that the AUTO
SURROUND mode is in use.
g
TUNER’s indicators
AUTO : This indicator illuminates when the
tuner’s Auto mode is in use.
TUNED : This indicator illuminates when the
tuner receives a sufficiently strong
radio signal.
ST(Stereo) : This indicator illuminates when an
FM station is being tuned into stereo
condition.
h
DTS-ES mode indicators
(DISC6.1, MTX6.1)
These indicators will illuminate to show the DTS-ES
decoding mode (Discrete 6.1 or Matrix 6.1).
NIGHT mode indicator
This indicator is illuminated when this unit is in the
Night mode, which reduces the dynamic range of
digital program material at low volume levels.
l
SPKR (speaker) AB indicator
This indicator is illuminated when the M (Multiroom)
speaker B system is active. (SR4002 only)
It displays the speaker system in use (A or B). When
the speakers are not in use, both lights (A and B) will
be turned off. (SR5002 only)
¡0
EQ mode indicator
This indicator is illuminated when the HT-EQ function
is active.
¡2
¡9
ANALOG input indicator
Main Information Display
This display shows messages relating to the status,
input source, surround mode, tuner, volume level or
other aspects of unit’s operation.
SIGNAL FORMAT indicators
2 DIGITAL
This indicator is illuminated when a Dolby Digital
signal is input.
EX
This indicator is illuminated when a Dolby Digital EX
signal is input.
dts
This indicator is illuminated when a DTS signal is
input.
ES
This indicator is illuminated when a DTS ES signal
is input.
96/24
This indicator is illuminated when a DTS 96/24 signal
is input.
PCM
This indicator is illuminated when the input signal is
PCM (pulse code modulation).
2 SURROUND
This indicator is illuminated when a Dolby Surround
signal is input.
¡6
™0
DIRECT (Puredirect) indicator
This indicator is illuminated when this unit is in the
SOURCE DIRECT or PURE DIRECT mode.
HDMI indicator
This indicator is illuminated when input terminal of
the HDMI component is connected to the unit.
PEAK indicator
This indicator is a monitor for an analog audio input
signal. If the selected analog audio input signal is
greater than the capable level of internal processing,
this will illuminate. If this happens, you should press
the ATT button.
¡1
¡4
¡5
SR
This indicator is illuminated when the Video-OFF
function is active.
SLEEP timer indicator
HDCD indicator
R
This indicator is illuminated when this unit is in the
display off mode.
This indicator is illuminated when the sleep timer
function in the main-room is in use.
¡8
This indicator is illuminated when the HDCD signal is
decoded from digital input signal.
This indicator is illuminated when an analog input
source has been selected.
LFE
PCM
DIGITAL Input Indicator
This indicator is illuminated when a digital input has
been selected.
ENGLISH
¡3
FL DISPLAY AND INDICATOR
ATT (Attenuation) indicator
This indicator is illuminated when the attenuation
function is active.
¡7
ENCODED CHANNEL STATUS
indicators
These indicators display the channels that are
encoded with a digital
input signal.
If the digital input signal is Dolby Digital 5.1ch or
DTS 5.1ch, “L”, “C”, “R”, “SL”, “SR” and “LFE” will be
illuminated.
If the digital input signal is 2 channel PCM-audio, “L”
and “R” will be illuminated.
If the digital input signal is Dolby Digital 5.1ch signal
with Surround EX flag or DTS-ES, “L”, “C”, “R”, “SL”,
“S” , “SR” and “LFE” will be illuminated.
7
SR4002-5002U DFU_01_E1_2.indd 7
07.7.9 2:46:46 PM
q
ENGLISH
REAR PANEL (SR4002)
w
!1
q
t
r
!3
INPUT
1
VIDEO
!6
HDMI Ver 1.1
INPUT
3
COMPONENT
VIDEO
MONITOR
OUT
S-VIDEO
FM (75
75))
GND
AM
ANTENNA
TV
L
SL
C
DVD
VCR IN
VCR OUT
DSS
MONITOR OUT
INPUT
2
CB/PB
Y
CR/PR
CB/PB
Y
INPUT 3
OUTPUT
4
1
R
SR
SW
7.1CH INPUT
INPUT 2
IN
3
R
(AUX2
AUX2))
INPUT 1
CR/PR
SBL
L
SBR
IN
TV
DVD
IN
OUT
VCR
DSS
OUT
TAPE
SL
C
FLASHER
IN
OPT
OUT
DIGITAL OUT REMOTE CONT.
DIGITAL IN
w
L
R
FRONT
R
SR
SW
L
R
SURROUND BACK
S. SPEAKER B
SBR
L
SURROUND
CENTER
SWITCHED
1.25A 150W
SPEAKER SYSTEMS : 6-8 OHMS
120V
y !0
!4
MODEL NO. SR4002
AM antenna and ground terminals
AC OUTLETS
PRE OUT
o
!5
60Hz
i
u
REAR PANEL (SR5002)
!1
w
!2
q
t
r
FM (75)
75)
S-VIDEO
GND
TV
SL
C
MONITOR
OUT 2
1
AM
ANTENNA
L
DVD
VCR IN
VCR OUT
DSS
MONITOR OUT
INPUT
2
CB/PB
Y
CR/PR
CB/PB
Y
4
L
1
SR
SW
7.1CH INPUT
CR/PR
Y
SBL
R
R
(AUX2
AUX2))
SBR
MULTI.
OUT
IN
TV
DVD
OUT
VCR
IN
DSS
OUT
TAPE
HDMI Ver 1.1
COMPONENT
VIDEO
IN
OUT
CD/CDR
CB/PB
INPUT 1
CR/PR
IN
INPUT 2
INPUT 3
OUTPUT
XM
5
2
3
DIGITAL IN
OPT
OUT
DIGITAL OUT REMOTE CONT.
FLASHER
DC
IN
TRIGGER
AUDIO
RS-232C
L
SL
SPEAKER C
OFF ON
C
AC IN
SBL
R
L
FRONT B
R
SR
SW
SBR
FRONT A OR B.CENTER.
FRONT A + B : 8 OHMS
R
L
FRONT A
R
SURROUND BACK
SPEAKER C/MULTI SPEAKER
y !0 !9
R
L
SURROUND
SURR.SURR BACK : 6-8 OHMS
PRE OUT
e
L
CENTER
SPEAKER
SYSTEMS
SWITCHED
1.25A 150W
120V
o
MODEL NO. SR5002
AC OUTLETS
60Hz
!4 !5 i !3
u!7 !8 @0
MONITOR OUT
This is a monitor output and each one includes both
composite video and S-video configurations. When
connecting two video monitors or televisions, be
aware that the OSD interface can be used with both
MONITOR OUT connections.
y
Preamp Outputs
(L, R, SL, SR, SBL, SBR, C)
Jacks for L(front left), R (front right), C (Center), SL
(surround left), SR (surround right), SBL (surround
back left) and SBR (surround back right).
Use these jacks for connection to external power
amplifiers.
u
AC INLET
Plug the supplied power cable into this AC INLET
and then into the power outlet on the wall.
This unit can be powered by 230V AC only.
e
Connect the AC power cable of component such as
a DVD or CD player to this outlet.
This outlet provides power only when this unit is
turned on.
r
INPUT
3
t
Connect the supplied AM loop antenna. Use the
terminals marked “AM” and “GND”. The supplied AM
loop antenna will provide good AM reception in most
areas. Position the loop antenna until you hear the
best reception.
RS-232C (SR5002 only)
The RS-232C port is to be used in conjunction with
an external controller to control the operation of the
SR5002 by using an external device.
!6
INPUT
1
VIDEO
FM antenna terminal (75 ohms)
Connect an external FM antenna with a coaxial
cable, or a cable network FM source.
AC IN
SBL
R
These are the video inputs and outputs. There
are 4 video inputs and 2 video outputs and each
one includes both composite video and S-video
configurations. Connect VCRs, DVD players, and
other video components to the video inputs.
The 2 video output channels can be used to be
connected to video tape recorders for making
recordings.
2
IN
OUT
CD/CDR
AUDIO
L
VIDEO IN/OUT
(TV, DVD, VCR, DSS)
COMPONENT VIDEO INPUT/
OUTPUT
If your DVD player or other device has component
video connectors, be sure to connect them to these
component video connectors on the unit. This unit
has two component video input connectors to obtain
the color information (Y, CB, CR) directly from the
recorded DVD signal or other video component and
one component video output connector to output it
directly into the matrix decoder of the display device.
By sending the pure DVD component video signal
directly, the DVD signal forgoes the extra processing
that normally would degrade the image. The result is
vastly increased image quality, with incredibly life like
colors and crisp detail.
When the video convert function is enabled, video and
S-video images can be output to the COMPONENT
MOINTOR OUT jack.
i
AC OUTLETS
Caution:
• In order to avoid potential turn-off thumps, anything
plugged into this outlet should be powered up before
this unit is turned on.
• The capacity of this AC outlet is 150W. Do not
connect devices that consume electricity more
than the capacity of this outlet. If the total power
consumption of the connected devices exceeds the
capacity, the protection circuit shuts down the power
supply.
o
Speaker outputs terminals
Seven terminals are provided for the front left,
front right, front center, surround left, surround
right, surround back left and surround back right
speakers.
Note:
You can use surround back speaker terminals as M
(Multiroom) SPEAKER B terminals, when you use
no surround back speaker.
8
SR4002-5002U DFU_01_E1_2.indd 8
07.7.9 2:46:47 PM
Subwoofer Output
Connect this jack to the line level input of a powered
subwoofer. If an external subwoofer amplifier is used,
connect this jack to the subwoofer amplifier input.
If you are using two subwoofers, either powered or
with a 2 channel subwoofer amplifier, connect a “Y”
connector to the subwoofer output jack and run one
cable from it to each subwoofer amplifier.
!1
7.1 CHANNEL or AUX2 INPUT
By connecting a DVD Audio player, Super Audio CD
multichannel player, or other components that has a
multichannel port, you can playback the audio with
5.1 channel or 7.1 channel outputs.
!2
Multiroom Outputs (SR5002 only)
These are the audio output jacks for the Multi zone
(Multi room).
Connect these jacks to optional audio power amplifiers
to listen the source selected by the multiroom system
in a remote room.
!3
REMOTE CONT. IN/OUT terminals
Connect to a Marantz component equipped with
remote control (RC-5) terminals.
!4
AUDIO IN/OUT (CD, TAPE, CD-R,
TV, DVD, VCR, DSS)
These are the analog audio inputs and outputs.
There are 6 audio inputs (4 of which are linked
to video inputs) and 3 audio outputs (1 of which
are linked to video outputs). The audio jacks are
nominally labeled for cassette tape decks, compact
disc players, DVD players and etc.... The audio inputs
and outputs require RCA-type connectors.
!5
DIGITAL INPUT
(SR4002 : Dig.1 - 4, SR5002 : Dig.1-5)
/ OUTPUT (optical)
ENGLISH
!0
These are the digital audio inputs and outputs.
The SR4002 has 2 digital inputs with coaxial jacks, 2
with optical jacks.
The SR5002 has 2 digital inputs with coaxial jacks, 3
with optical jacks.
The inputs accept digital audio signals from a CD,
DVD, or other digital source component.
For digital output, this is 1 optical output.
The digital outputs can be connected to MD recorders,
CD recorders, or other similar components.
!6
HDMI INPUT/OUTPUT
The SR4002 has 2 HDMI inputs and 1 HDMI output.
The SR5002 has 3 HDMI inputs and 1 HDMI output.
The input function can be selected from the OSD
menu system. (See page 27)
!7
DC TRIGGER output terminal
(SR5002 only)
Connect a device that needs to be triggered by DC
under certain conditions (screen, power strip, etc…)
Use the system OSD setup menu to determine the
conditions by which these jack will be active.
Note:
This output voltage is for (status) control only, It is not
sufficient for drive capability.
!8
FLASHER IN
(Flasher input terminal) (SR5002 only)
These terminals are to control the unit from each
zone. Connect the control signal from a Keypad, etc.
!9
SPEAKER C SELECTOR SWITCH
(SR5002 only)
The terminals can be used to connect a third set of
speakers by setting the SPEAKER C selector switch
to ON. For connection and use, see page 24.
@0
XM antenna terminal (SR5002 only)
Plug the XM Mini-Tuner and Home Dock into XM
terminal.
9
SR4002-5002U DFU_01_E1_2.indd 9
07.7.9 2:46:47 PM
ENGLISH
z
REMOTE CONTROLLER
The provided remote controller is a universal
remote controller. The POWER button, numeric
buttons and control buttons are used in common
across different input source components.
The input source controlled with the remote controller
changes when one of the input selector buttons is
pressed.
‹5
z
x
c
v
b
n
LEARN
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
1
CS
2
3
BAND
T.MODE
EX/ES
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
7
m
,
.
⁄0
⁄1
SEND
8
9
7.1CH IN
A/D
HT-EQ
0
+10
MEMO
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
CL
CH/ CAT
P.SCAN
VOLUME
INFO
MENU
T.TONE
/SET UP
EXIT
REC
⁄3
⁄4
⁄5
⁄6
-
T.DISP
PRESET
DISC+
+
PTY
-
TUNING
SUB TITLE
V-OFF
ATT.
BASS
DVD
‹0
VCR
AUDIO
‹1
‹2
‹3
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
REMOTE CONTROLLER
⁄3
This button is used to turn a specific source (such as
a DVD player) on or off independently from the rest
of the system.
0/7.1CH IN button
This button is used to select the output of an external
multi channel decoder.
F.DIRECT button
This button is used to select the "Frequency direct
input".
v
(+10) A/D button
This button is used to switch between the analog and
digital inputs.
PRESET +/- buttons
This button is used to select a preset station up and
down.
m
TUNING +/- buttons
This button is used to tune a frequency station up
and down.
Indicates when the remote controller is in the LEARN
mode.
x
SET button
This button is used to enter learn mode and preset
mode.
c
/ SOURCE ON/OFF button
SLEEP button
This button is used for setting the sleep timer.
b
DISPLAY button
This button is used to selects the display mode for the
front display of the unit.
n
Numeric buttons
These buttons are used to switch between 0 to +10
of the source components.
If the source is set to the amplifier, these buttons are
used to perform operations.
(When AMP mode is selected)
1/AUTO button
This button is used to select auto surround.
CL (Clear) button
This button is used to erase the memory or program
of a source.
SPKR A/B button (SR5002 only)
This button is used to select the speaker system.
The speaker system is switched in the following
sequence.
A → B → A+B → off
.
CH/CAT3 (UP) / 4 (DOWN) buttons
These buttons are used to change channels.
‹4
CONTROL buttons
These buttons are used when operating PLAY, STOP,
PAUSE and other commands of a source.
(When TUNER mode is selected)
T.DISP button
This button is used to select the display mode in
RDS.
PTY button
This button is used to display the programme type
information of the current station.
⁄4
,
ANGLE/V-OFF buton
(When AMP mode is selected)
This button is used to turn off the video signal.
⁄5
DISC+/CH. SEL button
(When AMP mode is selected)
This button is used to call up CH LEVEL ADJUST
and adjust speaker levels or 7.1 ch input level.
2/Dolby button
This button is used to select DOLBY mode.
⁄0
3/dts button
This button is used to select dts mode.
(When AMP mode is selected)
This button is used to turn on and off multi room.
These buttons are used to adjust the tone control
of low frequency sound for left, right and subwoofer
speaker.
⁄1
⁄7
MULTI/CAT button (SR5002 only)
+
TREBLE
TV
¤4
¤5
¤6
¤7
¤8
F.DIRECT
ANGLE
CH-SEL
¤3
¤9
ENTER
⁄2
⁄7
⁄8
⁄9
¤0
¤1
¤2
9/NIGHT button
Pressing this button prevents the Dolby Digital
signal from playback at a loud voice. This function
reduces the voice by 1/3 to 1/4 at maximum. Thus, it
eliminates the occurrence of an abruptly loud voice
at night. However, the function is valid only in the
case when the Dolby Digital signal is entered into
OPTICAL or COAXIAL and data to compress the
voice exists in the signal to be played back.
When this button is pressed, the “NIGHT” indicator
is illuminated.
LEARN indicator
4/CSII button
This button is used to select CSII mode.
5/EX/ES button
This button is used to select EX/ES mode.
INFO button
6/VIRTUAL button
This button is used to select VIRTUAL mode.
(When AMP mode is selected)
When this button is pressed, the current setting are
displayed on the TV monitor.
7/M-CH ST button
This button is used to select Multi Channel Stereo.
⁄2
8/STEREO button
This button is used to select STEREO mode.
⁄6
(When AMP mode is selected)
This button is used to enter the test tone menu. (2-4
speakers level)
SEND indicator
Indicates when the remote controller is transmitting
a signal.
⁄8
T.TONE/SET UP button
BASS +/- buttons
/ POWER ON and OFF buttons
(When AMP mode is selected)
These buttons are used to turn the unit on or off.
⁄9
SURROUND button
This button is used to selects the surround mode.
10
SR4002-5002U DFU_01_E1_2.indd 10
07.7.9 2:46:47 PM
P.DIRECT button
When this button is pressed, the tone control circuit
is bypassed.
¤6
VOLUME +/- buttons
This button is used to adjust the volume for the
amplifier and television.
Note:
¤1
BAND/LIP SYNC/INPUT button
(When AMP mode is selected)
This button is used to select LIP SYNC mode.
(When AMP mode is selected)
This button is used to turn on and off multi speaker.
T.MODE button
(When TUNER mode is selected)
This button is used to select auto stereo mode or
mono mode when the FM band is selected.
The “AUTO” indicator lights in the auto stereo mode.
¤3
P.SCAN button
(When TUNER mode is selected)
This button is used to start preset scan.
¤4
MEMO/HT-EQ button
This button is used to store setting to memory or
program a source.
(When AMP mode is selected)
This button is used to turn on or off HT(Home
Theater)-EQ mode. This mode compensates for the
audio portion of a movie sounding “bright”.
When this button is pressed, “EQ” indicator light up.
¤5
MUTE button
This button is used to mute the audio for the amplifier
and television.
Note:
Set the AMP mode to use this button with the unit.
(When DVD mode is selected)
This button is used to select one of the audio
language.
‹3
¤7
¤2
AUDIO buttons
Set the AMP mode to use this button with the unit.
(When TUNER mode is selected)
This button is used to select a radio band.
(When TV mode is selected)
This button is used to select monitor input.
‹2
¤8
M-SPKR button (SR5002 only)
MENU button
(When AMP mode is selected)
This button is used to call up the SETUP MAIN
MENU of the unit.
¤9
1, 2, 3, 4 (CURSOR) / ENTER buttons
These buttons are used when controlling the cursor
of the unit, DVD or other AV equipment.
‹0
EXIT button
(When AMP mode is selected)
This button is used to cancel setting in the setup
menu.
‹1
SUBTITLE/ATT. button
(When AMP mode is selected)
When the input signal is too high and the voice
distorts even by throttling the unit VOLUME control,
turn on this function.
“ATT” is indicated when this function is activated.
The input level reduced. Attenuator is invalid for the
output signal of “REC OUT”.
ENGLISH
¤0
TREBLE +/- buttons
These buttons are used to adjust the tone control of
high frequency sound for left and right speaker.
‹4
SOURCE button
These buttons are used to switch the source of your
A/V Receiver / amplifer. Each time a source button is
pressed, the remote controller changes to the source
which was pressed.
This remote controller can control 12 types of
equipment. To change the A/V Receiver / amplifier
source, press this button twice within two seconds.
The signal is sent when it is pressed the second
time.
Notes:
• Select the AMP as the source to use this remote
controller with the unit.
• In the case of the SR4002 or SR5002, the MD button
cannot be used.
‹5
Infrared Transmitter and Learning
Sensor
This transmitter emits infrared light. Press the buttons
while pointing the transmitter towards the infrared
receiver window of the unit or other AV equipment.
Be sure to also point towards other remote controllers
when using the learning function.
Note:
This function is unavailable while the digital input is
selected.
11
SR4002-5002U DFU_01_E1_2.indd 11
07.7.9 2:46:48 PM
ENGLISH
REMOTE CONTROL OPERATION
GENERAL INFORMATION OF REMOTE CONTROLLER TO THE UNIT
To control the unit by your remote controller, you have to select the device AMP or TUNER by pressing the
SOURCE button. Please refer below for the details in AMP and TUNER mode.
AMP MODE
TUNER MODE
LEARN
SOURCE
SEND
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
1
2
CS
3
EX/ES
BAND
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
7.1CH IN
A/D
P.SCAN
HT-EQ
0
+10
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
CL
CH/ CAT
T.MODE
MEMO
VOLUME
INFO
MENU
ENTER
T.TONE
/SET UP
EXIT
REC
-
T.DISP
PRESET
+
PTY
-
F.DIRECT
TUNING
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
BASS
TV
+
AUDIO
TREBLE
DVD
VCR
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
REMOTE CONTROLLER
SOURCE ON / OFF
POWER OFF
POWER ON
SLEEP
DISPLAY
P.DIRECT
SURROUND
AUTO (1)
DOLBY (2)
dts (3)
CSII (4)
EX/ES (5)
VIRTUAL (6)
M-CH ST (7)
STEREO (8)
NIGHT (9)
7.1CH IN (0)
A/D (+10)
LIP SYNC / INPUT
HT-EQ
SPKR A / B
MULTI / CAT
MUTE
M-SPKR
VOLUME 3 / 4
INFO
MENU
ENTER
CURSOR
T.TONE / SET UP
EXIT
CH-SEL
V-OFF
ATT.
BASS 3 / 4
TREBLE 3 / 4
SOURCE
Turns the SR4002/SR5002 on and off
Turns the SR4002/SR5002 off
Turns the SR4002/SR5002 on
Sets the sleep timer function
Changes the front display mode
Selects the pure direct mode
Selects the surround mode
Selects auto surround
Selects DOLBY mode
Selects dts mode
Selects CSII mode
Selects EX/ES
Selects VIRTUAL mode
Selects Multi Channel Stereo
Selects STEREO mode
Turns on or off NIGHT mode
Selects the 7.1CH IN
Switches between the analog or digital inputs
Selects the LIP SYNC mode
Turns on or off HT-EQ mode
Selects the speaker system
Turns on or off multi room
Decreases the sound temporarily
Turns on or off multi speaker
Adjusts the over all sound level
Displays the current setting on the monitor
Enters the "SETUP MENU"
Enters the "SETUP MENU"
Confirms the setting in "SETUP MENU" mode
Moves the cursor for setting in "SETUP MENU" mode
Enters the test tone menu
Exits from SETUP MENU
Calls up CH LEVEL ADJUST and adjusts speaker levels or 7.1ch input
level
Turns on or off video output
Reduces the input level
Adjusts the tone control of low frequency sound
Adjusts the tone control of high frequency sound
Selects a particular source component
LEARN
SOURCE
SEND
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
l/
SLEEP
AUTO
LIP SYNC/
INPUT
dts
1
CS
2
3
BAND
EX/ES
VIRTUAL
T.MODE
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
7.1CH IN
A/D
HT-EQ
0
+10
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
CL
CH/ CAT
P.SCAN
MEMO
VOLUME
INFO
MENU
ENTER
T.TONE
/SET UP
Inputs the numeric
Selects a radio band
Selects the auto stereo mode or mono mode
Starts preset scan
Clears the inputting
Enters the tuner preset memory numbers
Shows preset information
Selects the display mode in RDS
Displays the programme type information of the current station
Selects the “Frequency direct input”
Selects a preset station up and down
Tunes a frequency station up and down
EXIT
REC
-
0-9
BAND
T.MODE
P.SCAN
CL
MEMO
INFO
T.DISP
PTY
F.DIRECT
PRESET 3 / 4
TUNING 3 / 4
T.DISP
PRESET
DISC+
+
PTY
-
F.DIRECT
TUNING
ANGLE
SUB TITLE
V-OFF
ATT.
CH-SEL
BASS
+
AUDIO
TREBLE
TV
DVD
VCR
TUNER
CD
CDR
DSS
MD
TAPE
AUX1
AUX2
AMP
REMOTE CONTROLLER
12
SR4002-5002U DFU_01_E1_2.indd 12
07.7.9 2:46:48 PM
1.
2.
Press the desired SOURCE button.
Press the desired operation buttons to play the selected component.
• For details, refer to the component’s user guide.
• It may not be possible to operate some models.
CONTROLLING A MARANTZ DVD PLAYER (DVD MODE)
LEARN
SOURCE
SEND
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
1
2
3
BAND
T.MODE
EX/ES
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
CS
7.1CH IN
A/D
0
+10
CL
CH/ CAT
P.SCAN
HT-EQ
MEMO
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
MENU
ENTER
T.TONE
/SET UP
EXIT
REC
SOURCE ON / OFF
POWER OFF
POWER ON
0-9,+10
CL
MEMO
INFO
MENU
ENTER
CURSOR
VOLUME
INFO
-
ENGLISH
CONTROLLING MARANTZ COMPONENTS
T.DISP
PRESET
+
PTY
-
F.DIRECT
TUNING
Pause
Play
Stop
Previous/Next
+
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
TV
DVD
VCR
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
BASS
T.TONE / SET UP
EXIT
T.Tone/Set up
AUDIO
TREBLE
REMOTE CONTROLLER
Rewind/ Forward
DISC+
ANGLE
SUBTITLE
AUDIO
Turns the DVD player on and off
Turns the DVD player off
Turns the DVD player on
Inputs the numeric
Clears the inputting
Calls up programming menu
Displays the disc information
Calls up the menu of DVD disc
Enters the setting
Moves the cursor for setting in
"On Screen Display" mode
Enters the test tone menu
Exits from SETUP MENU
Calls up the setup menu of the
DVD player
Pause
Play
Stop
Skips forward or previous
chapter/track
Searchs forward or backward
DVD changer next disc
Selects the camera angle
Selects the subtitle language
Selects the audio language
CONTROLLING A MARANTZ CD (CD MODE)
LEARN
SOURCE
SEND
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
1
2
3
BAND
T.MODE
EX/ES
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
CS
7.1CH IN
A/D
0
+10
CL
CH/ CAT
P.SCAN
HT-EQ
MEMO
VOLUME
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
INFO
MENU
SOURCE ON / OFF
POWER OFF
POWER ON
0-9
CL
MEMO
INFO
MENU
Pause
Play
Stop
Previous/ Next
Rewind/ Forward
DISC+
Turns the CD player on and off
Turns the CD player off
Turns the CD player on
Inputs the numeric
Clears the inputting
Programs
Scrolls the disc information
Switches the display information
Pause
Play
Stop
Skips forward or previous track
Searchs forward or backward
CD changer next disc
CONTROLLING A MARANTZ VCR (VCR MODE)
LEARN
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
1
CS
2
3
BAND
T.MODE
EX/ES
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
7.1CH IN
A/D
0
+10
CL
CH/ CAT
-
PRESET
+
PTY
-
F.DIRECT
HT-EQ
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
INFO
MENU
TUNING
+
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
TV
DVD
VCR
DSS
TUNER
CD
CDR
TAPE
AUX1
AUX2
BASS
AUDIO
T.TONE
/SET UP
EXIT
REC
-
PRESET
+
PTY
-
F.DIRECT
TUNING
DISC+
ANGLE
SUB TITLE
V-OFF
ATT.
TV
DVD
VCR
MD
TUNER
CD
CDR
MD
AMP
TAPE
AUX1
AUX2
AMP
BASS
EXIT
REC
Pause
Play
Stop
Previous / Next
Rewind / Forward
AUDIO
Turns the VCR on and off
Inputs the numeric
Selects TV/VCR
Clears the inputting
Calls up programming menu
Selects VCR channel up or down
Calls up the menu
Enters the setting
Moves the cursor for setting in
"On Screen Display" mode
Exits the programming menu
Record
Pause
Play
Stop
Skips forward or previous track
Searchs forward or backward
Selects the audio language
+
CH-SEL
TREBLE
REMOTE CONTROLLER
T.DISP
SOURCE ON / OFF
0-9,+10
LIP SYNC/INPUT
CL
MEMO
CH 3 / 4
MENU
ENTER
CURSOR
MEMO
ENTER
EXIT
T.DISP
P.SCAN
VOLUME
ENTER
T.TONE
/SET UP
REC
SEND
AUDIO
TREBLE
DSS
REMOTE CONTROLLER
13
SR4002-5002U DFU_01_E1_2.indd 13
07.7.9 2:46:48 PM
ENGLISH
CONTROLLING A MARANTZ CD RECORDER (CDR MODE)
LEARN
SOURCE
SEND
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
1
CS
2
3
BAND
EX/ES
VIRTUAL
T.MODE
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
7.1CH IN
A/D
0
+10
CL
CH/ CAT
P.SCAN
HT-EQ
MEMO
VOLUME
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
INFO
MENU
SOURCE ON / OFF
POWER OFF
POWER ON
0-9
CL
MEMO
INFO
MENU
REC
Pause
Play
Stop
Previous / Next
Rewind / Forward
Turns the CD recorder on and off
Turns the CD recorder off
Turns the CD recorder on
Inputs the numeric
Clears the inputting
Programs
Scrolls the disc information
Switches the display information
Record
Pause
Play
Stop
Skips forward or previous track
Searchs forward or backward
CONTROLLING A MARANTZ MD DECK (MD MODE)
LEARN
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
1
CS
2
3
EX/ES
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
7.1CH IN
A/D
0
+10
CL
CH/ CAT
-
PRESET
+
P.SCAN
HT-EQ
MEMO
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
INFO
SOURCE ON / OFF
POWER OFF
POWER ON
0-9
CL
MEMO
MENU
REC
Pause
Play
Stop
Previous / Next
Rewind / Forward
Turns the MD deck on and off
Turns the MD deck off
Turns the MD deck on
Inputs the numeric
Clears the inputting
Programs
Switches the display information
Record
Pause
Play
Stop
Skips forward or previous track
Searchs forward or backward
LEARN
SOURCE
PTY
-
F.DIRECT
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
AUTO
1
CS
2
3
EX/ES
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
7.1CH IN
A/D
0
+10
CL
CH/ CAT
MENU
INFO
EXIT
T.TONE
/SET UP
TUNING
+
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
TV
DVD
VCR
DSS
TUNER
CD
CDR
TAPE
AUX1
AUX2
BASS
AUDIO
-
T.DISP
PRESET
+
PTY
-
F.DIRECT
TUNING
+
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
TV
DVD
VCR
DSS
MD
TUNER
CD
CDR
AMP
TAPE
AUX1
AUX2
TREBLE
BASS
REMOTE CONTROLLER
T.MODE
P.SCAN
HT-EQ
MEMO
VOLUME
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
SOURCE ON / OFF
POWER OFF
POWER ON
0-9
CL
MEMO
REC
Pause
Play
Stop
Previous / Next
Rewind / Forward
Turns the TAPE deck on and off
Turns the TAPE deck off
Turns the TAPE deck on
Inputs the numeric
Clears the inputting
Programs
Record
Pause
Play
Stop
Skips forward or previous track
Searchs forward or backward
MENU
ENTER
T.TONE
/SET UP
REC
SEND
l/
SLEEP
ENTER
EXIT
T.DISP
T.MODE
VOLUME
ENTER
T.TONE
/SET UP
REC
SEND
CONTROLLING A MARANTZ TAPE DECK (TAPE MODE)
AUDIO
EXIT
REC
-
PRESET
+
PTY
-
F.DIRECT
TUNING
+
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
TV
DVD
VCR
MD
TUNER
CD
CDR
MD
AMP
TAPE
AUX1
AUX2
AMP
TREBLE
REMOTE CONTROLLER
T.DISP
BASS
AUDIO
TREBLE
DSS
REMOTE CONTROLLER
14
SR4002-5002U DFU_01_E1_2.indd 14
07.7.9 2:46:49 PM
ENGLISH
CONTROLLING A MARANTZ UNIVERSAL DOCK (AUX1 MODE)
LEARN
SOURCE
SEND
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
1
CS
2
3
EX/ES
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
7.1CH IN
A/D
0
+10
CL
CH/ CAT
T.MODE
P.SCAN
HT-EQ
MEMO
VOLUME
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
INFO
SOURCE ON / OFF
POWER OFF
POWER ON
INFO
MENU
ENTER
CURSOR UP
CURSOR DOWN
Pause
Play
Stop
Previous/Next
P.SCAN
Turns the UNIVERSAL DOCK (Dock connector) ON and OFF
Turns the UNIVERSAL DOCK (Dock connector) OFF
Turns the UNIVERSAL DOCK (Dock connector) ON
Mode
Call up the menu
Enter the setting
Select contents Up
Select contents Down
Pause
Play / Pause
Stop
Skips forward or previous tracks
Shuffle
MENU
ENTER
T.TONE
/SET UP
EXIT
REC
-
T.DISP
PRESET
+
PTY
-
F.DIRECT
TUNING
+
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
TV
DVD
VCR
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
BASS
AUDIO
TREBLE
DSS
REMOTE CONTROLLER
15
SR4002-5002U DFU_01_E1_2.indd 15
07.7.9 2:46:49 PM
ENGLISH
BASIC OPERATION
NORMAL MODE
(When operating Marantz AV equipment products)
This remote controller is preset with a total of
12 types of remote codes, including Marantz TV
(television), DVD, VCR (VCR deck), DSS (satellite
broadcasting tuner), TUNER, CD, CD-R, MD, TAPE
(tape deck), AUX1, AUX2, and AMP (amplifier).
Learning is not necessary for Marantz products. You
can use these products without setting any codes.
Importants:
• Some codes may be not match your equipment.
In this case, you can use LEARN mode to store these
codes.
• The preset codes do not cover full functions.
If you need extra function, use LEARN mode to
store extra function.
• Wen the batteries are getting weak, the preset
procedure is not successful.
PRESET
+
-
TUNING
Press the SOURCE button.
For this example, press DVD.
Pressing the SOURCE button once changes
the remote control to the settings for the source
that was pressed.
To change the amplifier on other source, press
the SOURCE button twice (double-click). The
code is sent, and then the amplifier source
changes to DVD.
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
DVD
VCR
AUDIO
1.
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
AUTO
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
2.
4
M-CH ST
7
CL
2
3
EX/ES
VIRTUAL
5
6
CH/ CAT
STEREO
NIGHT
8
9
7.1CH IN
A/D
0
+10
SOURCE
HT-EQ
MEMO
MUTE
Remote controller
source name
TV
DVD
VCR
DSS
Corresponding preset
code
TV
DVD
VCR
SATELLITE
SEND
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
1.
LIP SYNC/
INPUT
dts
CS
2
3
EX/ES
VIRTUAL
4
5
6
DISC+
ANGLE
SUB TITLE
V-OFF
ATT.
BASS
3.
ON
SURROUND
dts
2
3
EX/ES
VIRTUAL
OFF
ON
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
3.
1
TV
DVD
VCR
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
4
5
6
STEREO
NIGHT
CL
CH/ CAT
8
P.SCAN
9
7.1CH IN
A/D
0
+10
SPKR A/B
MUTE
DISPLAY
P.DIRECT
SURROUND
SLEEP
1.
dts
LIP SYNC/
INPUT
AUTO
AUTO
1
2
3
1
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
CS
AUDIO
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
2.
EX/ES
VIRTUAL
5
6
STEREO
NIGHT
7
VCR
3
4
TREBLE
DVD
2
M-CH ST
CL
1.
OFF
l/
SLEEP
TV
SEND
SET
CH/ CAT
8
9
7.1CH IN
A/D
0
+10
T.MODE
P.SCAN
HT-EQ
MEMO
VOLUME
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
dts
LIP SYNC/
INPUT
2
3
EX/ES
VIRTUAL
5
6
M-CH ST
STEREO
NIGHT
AUTO
2
3
4.
7
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
TV
DVD
VCR
DSS
1.
TUNER
CD
CDR
MD
AUX1
AUX2
AMP
TAPE
8
9
7.1CH IN
A/D
0
+10
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
HT-EQ
AUDIO
TREBLE
INFO
2.
Press and hold down the SOURCE button
for appliance which should be controlled and
press SET button until the SEND indicator
blinking twice.
Then back light flushes.
2.
Press the below codes to reset.
TV : 1000
DVD : 2000
VCR : 3000
DSS : 4000
P.SCAN
MEMO
MENU
MENU
1.
T.MODE
VOLUME
INFO
ENTER
T.TONE
/SET UP
EXIT
The indicator will blink twice.
REMOTE CONTROLLER
1.
2.
Press and hold down the SOURCE button for
appliance which should be controlled and press
SET button until the SEND indicator blinking twice
then back light flushes.
Note:
After this procedure, the selected SOURCE button is
set initial code.
Press the INFO button.
MULTI/ CAT
M-SPKR
HT-EQ
INFO
To view the code for first digit, press 1 once.
Wait 3 seconds, count the SEND indicator
blinks (e.g. 3 blinks = 3) and write down the
number.
Note:
If a code digit is “0”, the SEND indicator will not
blink.
MEMO
VOLUME
DSS
5.
ON
SURROUND
4
CS
SLEEP
BASS
LIP SYNC/
INPUT
T.MODE
TREBLE
REMOTE CONTROLLER
1.
AUDIO
OFF
P.DIRECT
M-CH ST
7
T.MODE
SET
DISPLAY
AUTO
1
AUTO
OFF
P.DIRECT
AUTO
CH/ CAT
l/
SLEEP
CS
1
2.
3.
l/
Device name
Television
DVD player
Video deck
Satellite broadcasting
tuner equipment
SET
DISPLAY
l/
3.
SOURCE
2.
SOURCE
The SEND indicator will blink twice.
SCANNING THE CODE TABLE
CH-SEL
See the attached manufacturer number list for the
preset manufacturers, devices, preset numbers, and
other settings.
SLEEP
SEND
P.SCAN
VOLUME
SPKR A/B
SET
DISPLAY
l/
Note:
If the indicator did not blink twice, then repeat steps 1
through 2 and try entering the same code again.
SLEEP
ON
REMOTE CONTROLLER
SOURCE
Press and hold down the SOURCE button for the
appliance which should be controlled and press
SET button until the SEND indicator blinks twice.
Then back light flushes.
Press the 4-digit code for appliance (code table
at the end of this book)
When the procedure is successful, the SEND
indicator will blink twice.
SOURCE
LEARN
OFF
l/
CHECKING THE CODE
CL
LEARN
SEND
SET
BASS
Press ENTER button once to lock in the code.
1
2.
LEARN
Stop when the appliance turns off.
LEARN
PRESET MODE
(When operating non-Marantz AV equipment
products)
This remote controller is preset with remote control
codes from AV equipment by other manufacturers.
The preset codes are TV, VCR, DVD and DSS.
Settings can be made in one of two ways.
When the preset codes are set, the following codes
are contained in the source button of the remote
controller.
Aim the remote control at the appliance and
slowly alternate between pressing CH+ button
and the SOURCE ON/OFF button for the
appliance.
T.MODE
REMOTE CONTROLLER
1.
RESETTING THE CODE
SOURCE
TREBLE
CS
1.
SET
l/
SLEEP
1
BASS
TV
SETTING THE BACK LIGHT
Each time press the buttons, illuminate button 2
seconds.
To turn off back light, press and hold down the SET
and OFF button until SEND indicator blinks twice.
To turn on it again, press and hold down the SET and
ON button until SEND indicator blinks twice.
Initial is back light ON.
DISC+
Press and hold down the SOURCE button for
appliance which should be controlled and press
SET button until the SEND indicator blinking
twice. Then back light flushes.
+
SOURCE
1.
3.
4.
5.
PROGRAMMING WITH THE 4-DIGIT CODE
-
2.
MENU
4.
Repeat step 3 three more times for remaining
digits. Use 2 for the second digit, 3 for the third
digit, and 4 for the fourth digit.
ENTER
T.TONE
/SET UP
EXIT
Switch on the appliance which should be
controlled.
16
SR4002-5002U DFU_01_E1_2.indd 16
07.7.9 2:46:49 PM
4.
This remote controller is capable of learning and
storing codes used by other remote controls that you
already own.
For codes which are not learned, the remote
controller will transmit either the Marantz preset
codes from the initial settings, or remote codes from
another manufacturer’s AV equipment which is set
by the customer.
The receiver sensor for the remote controller signals is
located at the top of the remote controller.
Notes:
• This remote controller is capable to learn around 60
codes.
• When the batteries are getting weak , the learing
procedure is not successful.
LEARNING PROCEDURE
1.
Place the remote controller so that its infrared
signal transmitter is facing the infrared signal
receiver on the Marantz remote controller at a
distance of about 0.05 m (2 inches).
5
0.0
m
Select the button to be learned.
• LEARN indicator lights up.
l/
SLEEP
DISPLAY
AUTO
1
CS
4
5.
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
2
3
EX/ES
VIRTUAL
5
6
T.MODE
7.
8.
CODES
3.
Codes can be erased in three ways: by buttons,
sources, and by all memory contents.
1.
Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
MULTI/ CAT
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
ENTER
l/
SLEEP
AUTO
1
2.
2
INFO
MENU
3
T.TONE
/SET UP
4.
Select the SOURCE button to select the button
to be erased.
BASS
TREBLE
TV
DVD
VCR
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
Erasing the all SOURCES
1.
3.
When you have finished programming the
remote controller, press the SET button, then
LEARN indicator stops blinking and exits from
the LEARN mode.
MULTI/ CAT
Press and hold down the SLEEP button and
press the learned button twice to be erased.
• SEND indicator blinks twice and the mode
returns to LEARN mode.
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
SET
dts
LIP SYNC/
INPUT
SLEEP
AUTO
OFF
1
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
4.
EM
RE
MO
TE
CO
NT
RO
LLE
R
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
M-SPKR
l/
SLEEP
AUTO
1
3.
2
INFO
3
MENU
ENTER
Select the SOURCE button to select the
SOURCE.
BASS
TREBLE
TV
DVD
VCR
TUNER
CD
CDR
DSS
MD
TAPE
AUX1
AUX2
AMP
2
1
2.
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
2
M-SPKR
INFO
3
MENU
ENTER
Press and hold down the SLEEP button and
press POWER ON and POWER OFF button.
• LEARN indicator lights.
SOURCE
3
Notes:
• When the SEND indicator blinks once again,
the transmitting code is unavailable for remote
controller, or the transmitting signal is intercepted
by noise.
• If no buttons are pressed for approximately 1
minutes while in the LEARN mode, the remote
controller automatically exits from the LEARN
mode.
To return the NORMAL mode, press the SET
button.
1
Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
MULTI/ CAT
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
OFF
ON
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
AUTO
3.
Erasing the code by SOURCE
1.
SET
DISPLAY
l/
M-SPKR
2
3
Press ENTER button to continue erasing.
• The SEND indicator blinks twice and the
mode returns to LEARN mode.
• To cancel the erasing operation, do not
press ENTER button and simply touch any
other button.
l/
SLEEP
INFO
MENU
MENU
INFO
AUTO
1
2
3
ENTER
ENTER
2.
Press and hold down the SLEEP button and
press the learned SOURCE button twice to be
erased.
• LEARN indicator lights.
CH-SEL
REMOTE CONTROLLER
ON
SLEEP
ST
ON
OFF
SEND
SY
MULTI/ CAT
OFF
SET
AUTO
l/
SLEEP
SLEEP
SET
Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
l/
l/
SOURCE
To return the NORMAL mode, press the SET
button.
SOURCE
Repeat steps 3 to 6 to learn other SOURCE.
LEARN
Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
EXIT
ENTER
AUTO
2.
MENU
INFO
M-SPKR
REMOTE CONTROLLER
Repeat steps 4 and 5 to learn other buttons in
same SOURCE.
SOURCE
RC55
00SR
Press ENTER button to continue erasing.
• The SEND indicator blinks twice and the
mode returns to LEARN mode.
• To cancel the erasing operation, do not
press ENTER button and simply touch any
other button.
Erasing the code by buttons
Press and hold the button of the original remote
controller to learn until the SEND indicator
blinks twice.
Notes:
• When the SEND indicator blinks once, repeat this
step.
• If the LEARN indicator flashes when the SEND
indicator is lit, then the button cannot be learned.
• When the memory of the remote controller is full,
the LEARN and SEND indicators blink once. If
you want to learn the code, you should erase other
learned button.
6.
ERASING PROGRAMMED
(RETURNING TO INITIAL SETTINGS)
ENGLISH
LEARN MODE
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
1
2
3
V-OFF
ATT.
TV
DVD
VCR
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
BASS
T.TONE
/SET UP
4.
EXIT
To return the NORMAL mode, press the SET
button.
TREBLE
Note:
Erasing codes will return to the factory preset code,
or there will leave empty if the button has no factory
preset code.
17
SR4002-5002U DFU_01_E1_2.indd 17
07.7.9 2:46:50 PM
ENGLISH
CONNECTIONS
SPEAKER PLACEMENT
The ideal surround speaker system for this unit is 7speaker systems, using front left and right speakers,
a center speaker, surround left and right speakers,
a surround back left and right speakers, and a
subwoofer.
For best results we recommend that all front speakers
be of the same type, with identical or similar driver
units. This will deliver smooth pans across the front
sound stage as the action moves from side to side.
Your center channel speaker is very important as
over 80% of the dialog from a typical motion picture
emanates from the center channel.
It should possess similar sonic characteristics to the
main speakers. Surround channel speakers need not
be identical to the front channel speakers, but they
should be of high quality.
The surround back speaker is useful for playback
of Dolby Digital Surround EX or DTS-ES. One of
the benefits of both Dolby Digital and DTS is that
surround channels are discrete full range, while they
were frequency limited in earlier “Pro Logic’ type
systems.
Bass effects are an important part of home theater.
For optimal enjoyment a subwoofer should be used
as it is optimized for low frequency reproduction. If
you have full range front speakers, however, they
may be used in place of a subwoofer with proper
setting of the switches in the menu system.
Surround Left
Surround left and right speakers
When this unit is used in surround operation,
preferred location for surround speakers is on
side walls of the room, at or slightly behind
listening position.
The center of the center speaker should face
center of the room.
the
the
the
the
INVERT
OUTPUT
BTL
EXT. CONT. IN
REMOTE CONT.
MASTER SLAVE
MAX
VIDEO/
+5~13V DC
SYSTEM OUT
FU
INPUT
1
VIDEO
FM (75
75))
S-VIDEO
GND
TV
SL
C
DVD
VCR IN
VCR OUT
DSS
MONITOR OUT
INPUT
2
CB/PB
Y
CR/PR
MONITOR
OUT 2
CB/PB
Y
CR/PR
CB/PB
Y
SBL
4
L
1
R
R
(AUX2
AUX2))
SR
SW
7.1CH INPUT
SBR
MULTI.
OUT
HDMI Ver 1.1
COMPONENT
VIDEO
1
AM
ANTENNA
L
INPUT
3
IN
TV
DVD
OUT
VCR
IN
DSS
OUT
TAPE
IN
OUT
CD/CDR
INPUT 1
CR/PR
IN
INPUT 2
INPUT 3
OUTPUT
XM
5
2
3
DIGITAL IN
OPT
OUT
DIGITAL OUT REMOTE CONT.
FLASHER
DC
IN
TRIGGER
AUDIO
RS-232C
HEIGHT OF THE SPEAKER UNITS
L
SL
SPEAKER C
OFF ON
C
AC IN
SBL
R
Front left and right speakers, and a center speaker
Align the tweeters and mid-range drivers on the
three front speakers at the same height, as best as
possible.
L
FRONT B
R
SR
SW
SBR
FRONT A OR B.CENTER.
FRONT A + B : 8 OHMS
R
L
FRONT A
R
L
SURROUND BACK
SPEAKER C/MULTI SPEAKER
R
L
SURROUND
SURR.SURR BACK : 6-8 OHMS
PRE OUT
CENTER
SPEAKER
SYSTEMS
SWITCHED
1.25A 150W
MODEL NO. SR5002
AC OUTLETS
120V
60Hz
Surround left and right speakers, and surround
back speaker
Place the surround left, right and surround back
speakers higher than your ears by about 70cm – 1m.
Also place the speakers at the same height, as best
as possible.
Center
70cm
1m
Right
Left
Front A
22°
Front Right
1.
Strip away approx. 3/8 inch (10 mm) of wire
insulation.
2.
Twist the bared wire ends tight, to prevent short
circuits.
3.
4.
Loosen the knob by turning it counterclockwise.
5.
Tighten the knob by turning it clockwise to
secure the wire.
90°
Note:
Use magnetically-shielded speakers for front left, right
and the center speakers when the speakers are installed
near the TV.
Right
Left
Surround
SR5002 only
CONNECTING SPEAKER WIRE
30°
Front left and right speakers
We recommend to set the front L and R speakers
with 45-60 degrees from the listening position.
or
IN
OUT
SE
SPEAKER SYSTEM
MINIMUM 4 OHMS
Subwoofer
We recommend using a sub-woofer to have maximum
bass effect. As the subwoofer only handles low
frequencies, you can place it any where in the room.
0°
150°
INPUT
LEVEL
MIN
Surround back left and right speakers
Surround back speakers are required when a full 7.1channel system is installed.
Speakers should be placed on a rear wall, behind the
listening position.
The center of the center speaker should face the
center of the room.
Front Center
Surround Back
Right
INPUT
Surround
BACK
Right
Left
Powered
subwoofer
Power
Amplifier
Right
Left
Front B
Front Left
Surround Right
Passive
subwoofer
Subwoofer
Surround Back
Left
135°
110°
CONNECTING SPEAKERS
1.
2.
10 mm
3.
4.
5.
Insert the bare part of the wire into the hole in
side of each terminal.
Center speaker
Align the front line of the center speaker with the front
L/R speakers. Or place the center speaker a little
backward from the line.
18
SR4002-5002U DFU_01_E1_2.indd 18
07.7.9 2:46:51 PM
Note:
Be sure to connect the positive and negative cables for
the speaker properly. If they are miss-connected, the
signal phase will be reversed and the signal quality
will be corrupted.
Tape Deck
CD player
CD recorder
DIGITAL
OUTPUT
DIGITAL
INPUT
DIGITAL
OUTPUT
ENGLISH
CONNECTING AUDIO COMPONENTS
OUT IN
L
L
R
R
OUT IN
L
L
R
R
L R
L R
Analog Audio
L R
R L
R L
INPUT
1
VIDEO
FM (75
75))
INPUT
3
S-VIDEO
GND
TV
SL
C
DVD
VCR IN
VCR OUT
DSS
MONITOR OUT
INPUT
2
CB/PB
Y
CR/PR
MONITOR
OUT 2
CB/PB
Y
4
1
R
SR
SW
7.1CH INPUT
CR/PR
Y
SBL
L
R
(AUX2
AUX2))
SBR
MULTI.
OUT
IN
TV
DVD
OUT
VCR
IN
DSS
OUT
TAPE
Digital Audio (coaxial)
COMPONENT
VIDEO
1
AM
ANTENNA
L
L R
L R
Caution:
• Be sure to use speakers with the specified impedance
as shown on the rear panel of this unit.
• To prevent damage to circuitry, do not let the bare
speaker wires touch each other and do not let them
touch any metal
part of this unit.
• Do not touch the
speaker terminals
when the power is
on. It may cause
you to receive an
electric shocks.
• Do not connect more than one speaker cable to one
speaker terminal. Doing so may damage this unit.
IN
OUT
CD/CDR
CB/PB
CR/PR
IN
5
2
DIGITAL IN
Digital Audio (optical)
3
OPT
OUT
DIGITAL OUT REMOTE CONT.
FLAS
FLASHER
IN
AUDIO
RS-232C
CONNECTING A SUBWOOFER
L
SL
SPEAKER C
OFF ON
C
SBL
R
Use the PRE OUT SUBWOOFER jack to connect a
powered subwoofer (power amplifier built in).
If your subwoofer is a passive type (power amplifier
is not built in), connect a monaural power amplifier to
the PRE OUT SUBWOOFER jack and connect the
subwoofer to the amplifier.
L
FRONT B
R
SR
SW
SBR
FRONT A OR B.CENTER.
FRONT A + B : 8 OHMS
R
L
FRONT A
R
L
R
SURROUND BACK
SPEAKER C/MULTI SPEAKER
L
SURROUND
Caution:
Do not connect this unit and other components to mains
power until all connections between components have
been completed.
Notes:
• Insert all plugs and connectors securely. Incomplete
connections may make noise.
• Be sure to connect the left and right channels
properly.
Red connectors are for the R (right) channel, and
white connectors are for the L (left) channel.
• Be sure to connect input and output properly.
• Refer to the instructions for each component that is
connected to this unit.
• Do not bind audio/video connection cables with
power cords and speaker cables this will result in
generating a hum or other noise.
SWITCHED
1.25A 150W
AC OUTLETS
120V
R L
The output audio signal from the TAPE OUT jack and
the CD/CD-R OUT jack is the same signal which is
currently selected.
CENTER
SPEAKER
SYSTEMS
SURR.SURR BACK : 6-8 OHMS
PRE OUT
60Hz
R L
CONNECTING DIGITAL AUDIO COMPONENTS
• There are 4 digital inputs (SR4002), 5 digital
inputs (SR5002), 2 coaxial jacks and 2 optical
jacks (SR4002), 3 optical jacks (SR5002), on the
rear panel. You can use these jacks to input PCM,
Dolby Digital and DTS bitstream signals from a
CD, DVD, or other digital source components.
• There is one optical output jack on the rear panel.
These jacks can be connected to a CD recorder,
or a MD deck inputs, respectively.
• Refer to the instructions for each component. To
setup the digital audio format of DVD player, or
other digital source’s connected to digital input
jacks.
• Use fiber optical cables (optical) for DIG-1,2
(SR4002), DIG-1,2,3 (SR5002), input jacks. Use
75 ohms coaxial cables (for digital audio or video)
for DIG-3,4 (SR4002), DIG-4,5 (SR5002), input
jacks.
• You can designate the input for each digital input/
output jacks according to your component. See
page 27.
Notes:
• There is no Dolby Digital RF input jack. Please use
an external RF demodulator Dolby Digital decoder
when connecting the Dolby Digital RF output jack
of the video disc player to the digital input jack.
• The digital signal jacks on this unit conform to
the EIA standard. If you use a cable that does not
conform to this standard, this unit may not function
properly.
• Each type of audio jack works independently.
Signals input through the digital and analog jacks are
output through the corresponding digital and analog
jacks, respectively.
19
SR4002-5002U DFU_01_E1_2.indd 19
07.7.9 2:46:51 PM
ENGLISH
VIDEO, S-VIDEO , COMPONENT JACKS
CONNECTING VIDEO COMPONENTS
There are 3 types of video jacks on the rear panel.
VIDEO PROJECTOR
DVD player
DIGITAL
OUT
Y
Y
CB / PB CR / PR
VIDEO jack
The video signal for the VIDEO jacks is the
conventional composite video signal.
S-VIDEO
OUT
S-VIDEO jack
The video signal is separated into luminance (Y) and
color (C) signals for the S-VIDEO jack. The S-VIDEO
signals enables high-quality color reproduction. If
your video component has an S-VIDEO output, we
recommend to use it. Connect the S-VIDEO output
jack on your video component to the S-VIDEO input
jack on this unit.
DIGITAL
OUT
CB / PB CR / PR
L R
L R
L
L
VIDEO
OUT
AUDIO
OUT
COMPONENT S-VIDEO
VIDEO IN
IN
COMPONENT
VIDEO OUT
S-VIDEO VIDEO
OUT
OUT
AUDIO
OUT
Satellite Tuner
R
R
R L
INPUT
1
VIDEO
FM (75
75))
GND
DVD
TV
SL
C
COMPONENT
VIDEO
VCR IN
VCR OUT
MONITOR OUT
DSS
INPUT
2
CB/PB
Y
CR/PR
CB/PB
Y
CR/PR
Y
CB/PB
SBL
L
4
5
1
2
INPUT
1
VIDEO
MONITOR
OUT 2
1
AM
ANTENNA
L
INPUT
3
S-VIDEO
FM (75
75))
S-VIDEO
GND
1
AM
ANTENNA
CR/PR
IN
TV
L
INPUT
3
SL
C
DVD
VCR IN
VCR OUT
DSS
MONITOR OUT
INPUT
2
CB/PB
Y
CR/PR
4
L
R
R
(AUX2
AUX2))
SR
SW
7.1CH INPUT
SBR
MULTI.
OUT
IN
DVD
TV
OUT
VCR
IN
DSS
OUT
TAPE
IN
OUT
CD/CDR
3
DIGITAL IN
FLASHER
FL
IN
R
(AUX2
AUX2))
SR
SW
7.1CH INPUT
SBR
MULTI.
OUT
IN
TV
DVD
OUT
VCR
IN
DSS
AUDIO
RS-232C
L
SL
RS-232C
SBL
L
R
L
R
FRONT B
R
SR
SW
SBR
L
FRONT A
FRONT A OR B.CENTER.
FRONT A + B : 8 OHMS
R
L
SURROUND BACK
SPEAKER C/MULTI SPEAKER
R
SL
C
CENTER
SPEAKER
SYSTEMS
SWITCHED
1.25A 150W
AC OUTLETS
60Hz
L
R
FRONT B
R
3
DIGITAL IN
SR
SW
SBR
FRONT A OR B.CENTER.
FRONT A + B : 8 OHMS
L
FRONT A
R
L
SURROUND BACK
SPEAKER C/MULTI SPEAKER
R
L
SURROUND
CENTER
SPEAKER
SYSTEMS
SURR.SURR BACK : 6-8 OHMS
PRE OUT
R L
Video
Video
L R
S-VIDEO
S-VIDEO
L R
AUDIO
OUT
AUDIO
IN
L R
L R
L R
Analog Audio
Analog Audio
L R
L R
L R
S-VIDEO
OUT IN
2
IN
OUT
CD/CDR
SBL
R
120V
L R
OUT
TAPE
SPEAKER C
OFF ON
L
SURROUND
SURR.SURR BACK : 6-8 OHMS
PRE OUT
L R
Y
AUDIO
SPEAKER C
OFF ON
C
CR/PR
5
1
R
OPT
OUT
DIGITAL OUT REMOTE CONT.
CB/PB
Y
SBL
VIDEO
OUT IN
Digital Audio
(coaxial)
VIDEO
OUT
AUDIO
OUT
S-VIDEO
IN
VIDEO
IN
Digital Audio
(coaxial)
COMPONENT
VIDEO
Component jack
Make component video connections to a TV or
monitor with component inputs to produce higher
quality video images. Use a component video cable
or 3 video cords to connect the component video out
jacks on the unit to the monitor.
Notes:
• Be sure to connect the left and right audio channels
properly.
Red connectors are for the R (right) channel, and
white connectors are the for L (left) channel.
• Be sure to connect the inputs and outputs of the
video signals properly.
• This unit has the “TV-AUTO ON/OFF” function to
turn the TV ON or OFF automatically, by sensing
the incoming video signal from the VIDEO jacks.
• You may need to setup the digital audio output
format of your DVD player, or other digital source
components. Refer to the instructions of the each
component connected to the digital input jacks.
• There is no Dolby Digital RF input jack. Use an
external RF demodulator with a Dolby Digital
decoder to connect the Dolby Digital RF output jack
of the DVD player to the digital input jack on this
unit.
• The COMPONENT OUTPUT 1 and 2 terminals of
the SR5002 can output the same video signal.
• For details concerning the connection of Video
equipment, please see VIDEO CONVERT (page
35).
L R
Digital Audio
(optical)
Digital Audio
(optical)
VCR
TV
20
SR4002-5002U DFU_01_E1_2.indd 20
07.7.9 2:46:52 PM
HDMI JACK
This unit has 3 HDMI inputs and one HDMI output. It
can send digital video and audio signals from DVDs and
other sources directly to a display. It minimizes signal
degradation caused by analog conversion so that high
quality images can be enjoyed.
Select an input source from the OSD menu system.
(See page 27)
Notes:
• When the HDMI output is connected to a display
monitor that does not support HDCP*, signals are
not output. To view images in HDMI, it is necessary
to connect to a display that supports HDCP*.
• There may be no image output if connected to a
TV or display that is not compatible with the above
format.
• Refer to the instruction manual of the TV or display
to be connected to the unit for detailed information
regarding the HDMI terminal.
* HDCP: High-bandwidth Digital Content Protection
• When multiple components are connected to this
unit, turn power to unused components off to
prevent interference between them.
• Disconnecting or connecting cables with the power
on can damage the equipment. Turn the power off
before disconnecting or connecting cables.
• Some DVD-Audio disks disable downmixing.
These types of disks are not played back correctly
unless the left, center, right and surround left and
right speakers, and subwoofer are connected.
• If a DVD player that does not support HDMI 1.1 is
connected to the unit, multi channel PCM playback
is not possible even with DVD-Audio disks.
• If a DVD player or other device with DVI output is
connected to the unit, a separate audio cable (opticaldigital, coaxial digital or analog) is needed for the
audio signals. In this case, select the connected audio
input as explained in “1 INPUT SETUP”. (See page
27)
• Multi channel PCM signals and audio signals of 64
kHz or higher that are input from the HDMI jack are
not output from the DIGITAL OUT jacks.
• Depending on the quiality of the cable used, the
HDMI signal may be affected by noise.
• Audio units that use sampling frequencies of 128
kHz and above are not supported.
• When only HDMI components are connected, OSD
will not be displayed. (See page 26)
An HDMI cable (sold separately) is used to connect
the HDMI jack on the unit with the HDMI jack on a DVD
player, TV, projector or other component. To transmit
multichannel audio via HDMI, the connected player
must support multichannel audio transmission through
its HDMI jack.
HDMI video streaming is compatible with DVI in
principle. Therefore, it is possible to connect to a TV
or monitor that has a DVI terminal using an HDMI-DVI
conversion cable or plug. When connecting to a DVI
terminal, connect the audio signal separately.
INPUT
3
S-VIDEO
GND
C
DVD
VCR
R IN
VCR OUT
DSS
MONITOR OUT
INPUT
2
CB/PB
Y
CR/PR
MONITOR
OUT 2
4
1
R
SR
SW
7.1CH INPUT
RS-232C
L
SL
SBR
MULTI.
OUT
TV
IN
N
DVD
Y
CB/PB
OUT
VCR
IN
DSS
OUT
TAPE
IN
OUT
CD/CDR
INPUT 1
CR/PR
IN
INPUT 2
INPUT 3
OUTPUT
XM
5
2
DIGITAL IN
3
OPT
OUT
DIGITAL OUT REMOTE CONT.
FLASHER
DC
IN
TRIGGER
AUDIO
C
AC IN
SBL
L
FRONT B
SR
CR/PR
SPEAKER C
OFF ON
R
R
CB/PB
Y
SBL
L
R
(AUX2)
HDMI Ver 1.1
COMPONENT
VIDEO
1
AM
TV
SL
SW
PRE OUT
CONNECTING HDMI COMPONENTS
INPUT
1
ANTENNA
L
HDMI INPUT
HDMI OUTPUT
VIDEO
FM (75)
VIDEO PROJECTOR
ENGLISH
DVD player
CONNECTING HDMI COMPONENTS
SBR
FRONT A OR B.CENTER.
R.
FRONT A + B : 8 OHMS
MS
R
L
FRONT A
R
L
SURROUND BACK
SPEAKER C/MULTI SPEAKER
R
L
SURROUND
SURR.SURR BACK : 6-8 OHMS
CENTER
SPEAKER
SYSTEMS
SWITCHED
1.25A 150W
MODEL NO. SR5002
AC OUTLETS
120V
60Hz
Satellite Tuner
HDMI OUTPUT
Notes:
• Some HDMI components can be controlled over
the HDMI cable, but this unit cannot control other
components this way.
• When connected to a monitor (i.e., TV, projector,
etc.) that does not support HDCP, video and audio
are not output.
• DVI cables come with 24-pin and 29-pin plugs. This
unit supports 24-pin DVI-D cables; 29-pin DVI
cables cannot connect to it.
• Some source devices such as DVD players does not
support HDMI repeater like those of the unit. In such
case, pictures are not properly projected on monitors
such as TVs and projectors.
21
SR4002-5002U DFU_01_E1_2.indd 21
07.7.9 2:46:52 PM
ENGLISH
ADVANCED CONNECTING
CONNECTING THE REMOTE CONTROL JACKS
INPUT
1
INPUT
3
COMPONENT
VIDEO
MONITOR
OUT 2
1
DVD
VCR IN
VCR OUT
DSS
MONITOR OUT
INPUT
2
CB/PB
Y
CR/PR
CB/PB
Y
4
1
IN
R L
R L
R L
R L
DVD
R L
OUT
VCR
IN
DSS
OUT
TAPE
IN
OUT
CD/CDR
CR/PR
CB/PB
Y
2
INPUT 1
CR/PR
IN
5
2
RC OUT
3
DIGITAL IN
OPT
OUT
DIGITAL OUT REMOTE CONT.
FLASHER
DC
IN
TRIGGER
OPTION
AUDIO
R L
R L
R L
R L
AC IN
L
R
L
R
L
R
L
VIDEO
CENTER
FM (75
75))
L
CENTER
S-VIDEO
GND
AM
ANTENNA
TV
L
R
FRONT SURR.
SL
C
DVD
L
SURR.
BACK
SUB
WOOFER
R
(AUX2
AUX2))
SR
SW
7.1CH INPUT
RS-232C
L
SL
SBR
MULTI.
OUT
DVD
SURROUND
CENTER
SWITCHED
1.25A 150W
SPEAKER
SYSTEMS
SURR.
BACK
1
MODEL NO. SR5002
MODE
AC OUTLETS
60Hz
SUB
WOOFER
VCR
VC
Power
Amplifer
REMOTE
CONTROL
CD recorder
REMOTE
CONTROL
DVD player
REMOTE
CONTROL
CD player
SBL
R
DVD Audio player
or
Super Audio CD Multi
channel player
SURROUND BACK
SPEAKER C/MULTI SPEAKER
SURR.SURR BACK : 6-8 OHMS
IN
TV
SPEAKER C
OFF ON
C
FRONT A
120V
R
FRONT SURR.
R
FRONT
TB
FRONT A OR B.CENTER.
CENTER.
FRONT A + B : 8 OHMS
L
VCR IN
SBL
L
Subwoofer
IN
IN
IN
OUT
OUT
OUT
FRONT B
R
SR
SW
SBR
FRONT A OR B.CENTER.
FRONT A + B : 8 OHMS
EXTERNAL INTERNAL
PRE OUT
L R
L R
EXTERNAL INTERNAL
EXTERNAL INTERNAL
L R
Front
Front
Center
Right
Left
Surround
Surround
Left
Right
Surround
Back Left
Surround
Back Right
CONNECTING MULTI CHANNEL AUDIO SOURCE
CONNECTING AN EXTERNAL POWER AMPLIFIER
The 7.1CH INPUT jacks are for multichannel audio
source such as a Super Audio CD multichannel
player, DVD audio player or external decoder.
If you use these jacks, switch on the 7.1CH INPUT
and set the 7.1CH INPUT level by using the SETUP
MAIN MENU. See page 31.
The PREOUT jacks are for connecting external
power amplifiers.
Be sure to connect each speaker to the corresponding
external power amplifier.
q
You can control other Marantz products through this
unit with the remote controller by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote controller
is received by the remote sensor on this unit. Then
the signal is sent to the connected device through
this terminal. Therefore you need to aim the remote
signal only to the unit. Also, if a Marantz power
amplifier (some models excluded) is connected to
one of these terminals, the power amplifier’s, power
switch is synchronized with this unit’s power switch.
Set the REMOTE CONTROL SWITCH on the
back of other units (not the SR4002/SR5002) to
“EXT”.(EXTERNAL) to use this feature.
w
Whenever external infrared sensors or similar
devices are connected to RC-5 IN of the unit, be sure
to always disable operation of the infrared sensor on
the unit by using the following procedure.
1.
Hold down the 7.1CH INPUT (SR4002) / MULTI
(SR5002) button and MENU button on the front
panel at the same time for five seconds.
2.
The setting “IR=ENABLE” is shown on the FL
DISPLAY.
3.
Press the 1 or 2 cursor button to change this to
“IR=DISABLE”.
4.
Press the ENTER button. Once this setting
is made, the infrared sensor on the unit is
disabled.
Note:
Be sure to set to “IR=ENABLE” when external
infrared sensors or similar devices are not connected.
Otherwise, the unit will be unable to receive remote
control commands.
5.
To restore the original setting, perform steps 1
to 4 to set to “IR=ENABLE”.
22
SR4002-5002U DFU_01_E1_2.indd 22
07.7.9 2:46:52 PM
AM Loop
Antenna
FM External
Antenna
Connecting the supplied FM antenna
The supplied FM antenna is for indoor use only.
During use, extend the antenna and move it in various
directions until the clearest signal is received.
Fix it with push pins or similar implements in the
position that will cause the least amount of distortion.
If you experience poor reception quality, an outdoor
antenna may improve the quality.
AM External
Antenna
FM Antenna
INPUT
1
VIDEO
FM (75
75))
GND
TV
SL
C
DVD
VCR IN
VCR OUT
DSS
MONITOR OUT
INPUT
2
CB/PB
Y
CR/PR
MONITOR
OUT 2
CB/PB
Y
4
1
R
SR
SW
7.1CH INPUT
CR/PR
Y
SBL
L
R
(AUX2
AUX2))
SBR
MULTI.
OUT
IN
TV
DVD
OUT
VCR
IN
DSS
OUT
TAPE
HDMI Ver 1.1
COMPONENT
VIDEO
1
AM
ANTENNA
L
INPUT
3
S-VIDEO
IN
OUT
CD/CDR
CB/PB
INPUT 1
CR/PR
IN
INPUT 2
INPUT 3
XM
5
2
DIGITAL IN
3
OPT
OUT
DIGITAL OUT REMOTE CONT.
FLASHER
DC
IN
TRIGGER
OUTPUT
ENGLISH
CONNECTING THE SUPPLIED ANTENNAS
CONNECTING THE ANTENNA TERMINALS
Connecting the supplied AM loop antenna
The supplied AM loop antenna is for indoor use
only.
Set it in the direction and position it to where you
receive the clearest sound. Put it as far away as
possible from the unit, televisions, speaker cables,
and power cords.
If you experience poor reception quality, an outdoor
antenna may improve the quality.
AUDIO
RS-232C
L
SL
SPEAKER C
OFF ON
C
R
L
R
FRONT B
R
SR
SW
SBR
1.
Press and hold down the lever of the AM
antenna terminal.
2.
3.
Insert the bare wire into the antenna terminal.
AC IN
SBL
FRONT A OR B.CENTER.
FRONT A + B : 8 OHMS
L
FRONT A
R
L
SURROUND BACK
SPEAKER C/MULTI SPEAKER
R
L
SURROUND
SURR.SURR BACK : 6-8 OHMS
PRE OUT
CENTER
SPEAKER
SYSTEMS
SWITCHED
1.25A 150W
MODEL NO. SR5002
AC OUTLETS
120V
60Hz
Release the lever.
CONNECTING AN FM OUTDOOR ANTENNA
ASSEMBLING THE AM LOOP ANTENNA
1.
Release the vinyl tie and take out the connection
line.
4.
Place the antenna on stable surface.
Notes:
• Keep the antenna away from noise sources (neon
signs, busy roads, etc.).
• Do not put the antenna close to power lines. Keep it
well away from power lines, transformers, etc.
• To avoid the risk of lightning and electrical shock,
grounding is necessary.
CONNECTING AN AM OUTDOOR ANTENNA
2.
Bend the base part in the reverse direction.
An outdoor antenna will be more effective if it is
stretched horizontally above a window or outside.
Notes:
• Do not remove the AM loop antenna.
• To avoid the risk of lightning and electrical shock,
grounding is necessary.
3.
Insert the hook at the bottom of the loop part
into the slot at the base part.
23
SR4002-5002U DFU_01_E1_2.indd 23
07.7.9 2:46:53 PM
ENGLISH
XM RADIO OVERVIEW (SR5002 ONLY)
SR5002 is the XM Ready® receiver. You can receive XM Satellite Radio® by connecting to the XM Mini-Tuner
and Home Dock (sold separately) and subscribing the XM service.
CONNECTING THE XM CONNECT-AND-PLAY ANTENNA
• Plug the XM Mini-Tuner and Home Dock into XM terminal on the rear panel.
• Position the XM antenna near a south-facing window to receive the best signal.
When making connections, also refer to the operating instructions of the XM Mini-Tuner and Home Dock.
Introducing XM Satellite Radio
There’s a world of audio listening pleasure beyond AM and FM. XM Satellite Radio which includes:
• Over 170 Digital Channels
• The most commercial-free music in satellite radio
• Live concerts plus exclusive original programming
• The biggest names in news, talk, and entertainment
• The most sports play-by-play
• Major league Baseball. Every team. All season long.
XM
INPUT
3
MONITOR
OUT 2
CB/PB
CR/PR
How to Subscribe
Listeners can subscribe by visiting XM on the Web at www.xmradio.com or by calling XM’s Listener Care at
(800) 967-2346. Customers should have their Radio ID and credit card ready. The Radio ID can be found by
selecting channel 0 on the radio.
(See the “CHECKING THE XM SIGNAL STRENGTH AND RADIO ID”)
A Warning Against Reverse Engineering
It is prohibited to copy, decompile, disassemble, reverse engineer, or manipulate any technology incorporated
in receivers compatible with the XM Satellite Radio system.
Furthermore, the AMBE® voice compression software included in this product is protected by intellectual
property rights including patent rights, copyrights, and trade secrets of Digital Voice Systems, Inc. The user of
this or any other software contained in an XM Radio is explicitly prohibited from attempting to copy, decompile,
reverse engineer, or disassemble the object code, or in any other way convert the object code into humanreadable form. The software is licensed solely for use within this product.
Y
CB/PB
INPUT 1
CR/PR
IN
INPUT 2
INPUT 3
OUTPUT
XM
5
2
Questions? Visit www.xmradio.com <http://www.xmradio.com/>
HDMI Ver 1.1
COMPONENT
VIDEO
DIGITAL IN
3
OPT
OUT
DIGITAL OUT REMOTE CONT.
FLASHER
DC
IN
TRIGGER
AC IN
CENTER
NTER
SPEAKER
AKER
SYSTEMS
TEMS
SWITCHED
1.25A 150W
MODEL NO. SR5002
AC OUTLETS
120V
60Hz
Note
• Keep the power supply cord unplugged until the XM Mini-Tuner and Home Dock connection have been
completed.
XM $ 12.95 monthly service subscription sold separately. XM Mini-Tuner and Home Dock required to
receive XM service (sold separately). Installation costs and other fees and taxes, including a one-time
activation fee may apply. Subscription fee is consumer only. All fees and programming subject to change.
Channels with frequent explicit language are indicated with an XL. Channle blocking is available for XM
radio receivers by calling 1-800-XMRADIO. Subscriptions subject to Customer Agreement available at
xmradio.com. XM service only available in the 48 contiguous United States. [XM Ready, XMDirect*] are
trademarks of XM Satellite Radio Inc. © 2006 XM Satellite Radio Inc. All rights reserved.
24
SR4002-5002U DFU_01_E1_2.indd 24
07.7.9 2:46:53 PM
Bi-amp Connection
A bi-amp connection is possible with speakers that
have two sets of inputs (for treble and bass).
This allows you to drive the treble and bass units
with separate channel amps, which enables better
sound quality. Connect the speakers as shown in the
figure. Set the SPEAKER C selector switch on the
rear panel to ON.
(Multi room speaker B)
RIGHT
SPEAKER
ENGLISH
CONNECTING FOR SPEAKER C USE (SR5002 only)
CONNECTING FOR THE MULTI ROOM (SR5002 only)
LEFT
SPEAKER
Notes:
• If incorrectly connected, a protective circuit in the
SR5002 will trip and set the SR5002 to standby.
(The STANDBY indicator will flash.) In such case,
recheck the connections between the speakers and
the SR5002.
• Turn power to the SR5002 off before changing the
setting of the SPEAKER C selector switch.
INPUT
1
VIDEO
FM (75
75))
GND
AM
TV
SL
C
DVD
VCR IN
VCR OUT
DSS
MONITOR OUT
INPUT
2
CB/PB
Y
CR/PR
CB/PB
Y
4
1
R
SR
SW
7.1CH INPUT
CR/PR
Y
CB/PB
SBL
L
R
(AUX2
AUX2))
COMPON
COMPONENT
VIDEO
VIDE
1
ANTENNA
L
INPUT
3
S-VIDEO
SBR
MULTI.
OUT
IN
TV
DVD
OUT
VCR
IN
DSS
OUT
TAPE
IN
OUT
CD/CDR
5
2
DIGITAL IN
3
OPT
OP
DIGITAL OUT
AUDIO
RS-232C
FM (75
75))
INPUT
1
VIDEO
SPEAKER C
OFF ON
SPEAKER C
OFF ON
SL
C
GND
AM
TV
SBL
L
R
L
R
L
R
L
R
SL
C
DVD
VCR IN
VCR OUT
DSS
MONITOR OUT
INPUT
2
CB/PB
Y
MONITOR
OUT 2
CR/PR
L
4
1
R
FRONT B
SR
SW
PRE OUT
SBR
FRONT A OR B.CENTER.
FRONT A + B : 8 OHMS
FRONT A
SURROUND BACK
SPEAKER C/MULTI SPEAKER
SURROUND
SURR.SURR BACK : 6-8 OHMS
MULTIROOM
CENTER
SPEAKER
SYSTEMS
R
(AUX2
AUX2))
SR
SW
7.1CH INPUT
MULTIROOM
RIGHT
SPEAKER
CR/PR
Y
CB/PB
SBR
MULTI.
OUT
IN
TV
DVD
OUT
VCR
IN
DSS
OUT
TAPE
IN
OUT
CD/CDR
L
SL
C
2
3
DIGITAL IN
DIGI
OPT
OUT
DIGITAL OUT REMOTE CONT.
FLASHER
DC
IN
TRIGGER
AC IN
SBL
R
L
FRONT B
R
SR
SW
PRE OUT
SBR
FRONT A OR B.CENTER.
FRONT A + B : 8 OHMS
R
L
FRONT A
R
L
SURROUND BACK
SPEAKER C/MULTI SPEAKER
R
L
SURROUND
SURR.SURR BACK : 6-8 OHMS
CENTER
SPEAKE
SPEAKER
SYSTEMS
SYSTEM
SWITCHED
1.25A 150W
AC OUTLETS
120V
R L
L
R
MAIN AMP
(For multiroom)
Note:
You can use surround back speaker terminals as multi
room speaker terminals when you use no surround
back speaker.
25
SR4002-5002U DFU_01_E1_2.indd 25
INPUT 2
5
SPEAKER C
OFF ON
L R
FRONT
INPUT 1
CR/PR
IN
AUDIO
RS-232C
MULTIROOM
LEFT
SPEAKER
CB/PB
Y
SBL
L
R
COMPONENT
VIDEO
1
ANTENNA
L
INPUT
3
S-VIDEO
07.7.9 2:46:53 PM
60Hz
MODEL NO. SR5
ENGLISH
CONNECTING OTHER EQUIPMENT
a
d
INPUT
1
VIDEO
INPUT
3
S-VIDEO
FM (75
75))
GND
TV
SL
C
DVD
VCR IN
VCR OUT
DSS
MONITOR OUT
INPUT
2
CB/PB
Y
CR/PR
MONITOR
OUT 2
CB/PB
Y
4
1
R
SR
SW
7.1CH INPUT
CR/PR
Y
SBL
L
R
(AUX2
AUX2))
SBR
MULTI.
OUT
IN
TV
DVD
OUT
VCR
IN
DSS
OUT
TAPE
HDMI Ver 1.1
COMPONENT
VIDEO
1
AM
ANTENNA
L
s
IN
OUT
CD/CDR
CB/PB
INPUT 1
CR/PR
IN
INPUT 2
INPUT 3
OUTPUT
XM
5
2
DIGITAL IN
3
OPT
OUT
DIGITAL OUT REMOTE CONT.
FLASHER
DC
IN
TRIGGER
AUDIO
RS-232C
L
SL
SPEAKER C
OFF ON
C
AC IN
SBL
R
L
FRONT B
R
SR
SW
SBR
FRONT A OR B.CENTER.
FRONT A + B : 8 OHMS
R
L
FRONT A
R
L
SURROUND BACK
SPEAKER C/MULTI SPEAKER
R
L
SURROUND
SURR.SURR BACK : 6-8 OHMS
PRE OUT
CENTER
SPEAKER
SYSTEMS
SWITCHED
1.25A 150W
MODEL NO. SR5002
AC OUTLETS
120V
60Hz
a RS232C
Connect an external control device or other device for
servicing. (Use a straight cable for the connection.)
s DC OUT (DC TRIGGER)
External devices can be controlled from the SR5002
by connecting them to the DC OUT terminal (12 V).
(See page 30)
d FLASHER IN
This unit can be controlled by connecting a control
box or other control device to this unit.
26
SR4002-5002U DFU_01_E1_2.indd 26
07.7.9 2:46:53 PM
SETUP MAIN MENU
After all components are connected, initial setup
must be performed.
1-1 INPUT SETUP
FUNC:MODE :DIG:HDMI:COMP
-----------------------TV
:AUTO : 5 : : DVD :AUTO : 1 : 1
: 1
VCR :AUTO : 3 : 3
: 3
DSS :AUTO : 2 : 2
: 2
AUX1:AUTO : F : : -
ON SCREEN DISPLAY MENU SYSTEM
This unit incorporates an on-screen menu system,
which makes various operations possible by using
the cursor (3, 4, 1, 2) and ENTER buttons on the
remote control or on the front panel.
MAIN
Note:
To view the on-screen displays, make certain you have
made a connection from the Monitor Out jack on the
rear panel to the composite, S-Video, component video
input of your TV or projector. (see page20)
1.
Press the AMP button of the remote
controller.(This step is not needed when
operating the setup menus from the unit itself.)
2.
Press the MENU button on the remote controller
or set to display the “SETUP MAIN MENU” of
the OSD menu system.
Select a desired sub-menu with the 3 or 4
cursor buttons, and press the ENTER button
to enter. The display will change to the selected
sub-menu. You can lock the condition of setup
to each sub-menu with the 1 or 2 or cursor
buttons.
Note:
If you desire to adjust any sub-menu, you need to set
it to UNLOCKED.
NEXT
1-2 INPUT SETUP
FUNC:MODE :DIG:HDMI:COMP
-----------------------TAPE:AUTO : - :
:
CD/R:AUTO : 4 :
:
AUX2:AUTO : - :
:
INPUT SETUP
:UNLOCK
SPEAKER SETUP:UNLOCK
PREFERENCE
:UNLOCK
SURROUND
:UNLOCK
PLIIx MUSIC
:UNLOCK
CSII
:UNLOCK
7.1 CH. INPUT:UNLOCK
MULTI ROOM
:UNLOCK
EXIT
* “8. MULTI ROOM” is displayed only with
the SR5002.
4 SURROUND
SURR.MODE :AUTO
HT-EQ
:OFF
LFE LEVEL :
MAIN
EXIT
5 PLIIx MUSIC PARAMETER
3 PREFERENCE
STANDBY MODE
TV-AUTO
OSD INFO
BILINGUAL
VIDEO CONVERT
HDMI
DC TRIGGER
:
:
:
:
ECONOMY
DISABLE
ENABLE
MAIN
: ENABLE
MAIN
EXIT
PARAMETER
: DEFAULT
PANORAMA
: OFF
DEMENSION
:
0
CENTER WIDTH :
3
MAIN
EXIT
* “DC TRIGGER” is displayed only with the SR5002.
MAIN
RETURN
EXIT
6 CSII PARAMETER
3-1 VIDEO CONVERT
AUTO
AUTO SETUP
START
TV
DVD
VCR
DSS
AUX1
2-1 SPEAKER SETUP
CANCEL
SPEAKER SETUP : AUTO
:
:
:
:
:
TRUBASS
SRS DIALOG
ON
ON
ON
ON
ON
: 0
: 0
SET MICROPHONE
SPEAKERS
SPEAKERS
SPEAKERS
SPEAKERS
MAIN
CHECK
LEVEL
DISTANCE
SIZE
RETURN
NEXT
:
:
:
:
MAIN RETURN
EXIT
MAIN
NEXT
EXIT
MANUAL
2-2 SPEAKERS SIZE
4.
1.
2.
3.
4.
5.
6.
7.
8.
EXIT
* For the SR4002, “–” is displayed for TV DIG
and VCR HDMI.
There are 8 items in the SETUP MAIN MENU.
3.
ENGLISH
SETUP
If you desire to exit from this menu system,
press the EXIT button, or move the cursor to
EXIT and press the ENTER button.
When only HDMI components are connected, the
OSD menu will not be displayed on the screen.
EXIT
MAIN
EXIT
SR5002 only
3-2 DC TIRGGER SETUP
DC TRIG
DISABLE
SUBWOOFER
: YES
FRONT L/R
: LARGE
CENTER
: SMALL
SURROUND L/R
: SMALL
SURR.BACK
: 2CH
SURR.BACK SIZE
: SMALL
LPF/HPF
: 100Hz
BASS MIX
: BOTH
MAIN
NEXT
EXIT
TV
DVD
VCR
DSS
AUX1
:
:
:
:
:
2-3 SPEAKERS
DISTANCE UNIT
FRONT L
FRONT R
CENTER
SURR.L
SURR.R
SUB W
SURR.B L
SURR.B R
MAIN
RETURN
2-4 SPEAKERS
TEST MODE
FRONT L
CENTER
FRONT R
SURR.R
SURR.B R
SURR.B L
SURR.L
SUB W
MAIN
RETURN
MAIN RETURN
TAPE :
CD/R :
AUX2 :
TUNER:
7.1CH:
EXIT
7 7.1 CH. INPUT LEVEL
VIDEO-IN
:
LAST
FRONT L
:
0 dB
CENTER
:
0 dB
FRONT R
:
0 dB
SURR.R
:
0 dB
SURR.B R
:
0 dB
SURR.B L
:
0 dB
SURR.L
:
0 dB
SUB W
:
0 dB
MAIN
EXIT
SR5002 only
2-3 SPEAKERS
DISTANCE UNIT
FRONT L
FRONT R
CENTER
SURR.L
SURR.R
SUB W
SURR.B L
SURR.B R
MAIN
RETURN
DISTANCE
: ft
: 10.0 ft
: 10.0 ft
: 10.0 ft
: 10.0 ft
: 10.0 ft
: 10.0 ft
: 10.0 ft
: 10.0 ft
NEXT
EXIT
DISTANCE
:
m
: 3.0 m
: 3.0 m
: 3.0 m
: 3.0 m
: 3.0 m
: 3.0 m
: 3.0 m
: 3.0 m
NEXT
EXIT
LEVEL
:
MANUAL
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
EXIT
8 MULTI ROOM
AUDIO
: DVD
SLEEP TIMER
: OFF
MULTI:OUT
: STEREO
MULTI:OFF
MSPK
:
VOL
: VARI
LEVEL
: -90dB
--- MAIN ROOM STATUS --VIDEO:DVD
AUDIO:DVD
MAIN
EXIT
27
SR4002-5002U DFU_01_E2_2.indd 27
07.7.9 2:47:30 PM
ENGLISH
1 INPUT SETUP (ASSIGNABLE DIGITAL
INPUT AND COMPONENT VIDEO INPUT)
Use this menu to select the input jack to be assigned
to the input source.
1.
Select “INPUT SETUP” in SETUP MAIN
MENU with 3 or 4 cursor button, and press the
ENTER button.
Notes:
• When the TUNER is fixed to the analog input, you
can not select any digital input.
• When a DTS-LD or DTS-CD is playing, this setup is
not available. This is to avoid noise being generated
from the analog input.
• If “AUTO” is selected and a DVD, compact disc
or LD is fast-forwarded during playback, decoded
signals may produce a skipping sound. In such cases,
change the setting to “DIG”.
2 SPEAKER SETUP
After you have installed the unit, connected all the
components, and determined the speaker layout, it
is now time to perform the settings in the Speaker
Setup menu for the optimum sound acoustics for
your environment and speaker layout.
Before you perform the following settings, it is
important that you first determine the following
characteristics:
1-1 INPUT SETUP
FUNC:MODE :DIG:HDMI:COMP
-----------------------TV
:AUTO : 5 : : DVD :AUTO : 1 : 1
: 1
VCR :AUTO : 3 : 3
: 3
DSS :AUTO : 2 : 2
: 2
AUX1:AUTO : F : : MAIN
NEXT
EXIT
* For the SR4002, “–” is displayed for TV DIG
and VCR HDMI.
FUNC:MODE :DIG:HDMI:COMP
-----------------------TAPE:AUTO : - :
:
CD/R:AUTO : 4 :
:
AUX2:AUTO : - :
:
2.
3.
RETURN
EXIT
To select the input source and MODE, press
the 3 or 4 cursor buttons.
To select “DIG” “HDMI” or “COMP” for the input
jack, press the 1 or 2 cursor buttons.
Select “AUTO” for input sources, for automatic
detection of the digital input signal condition.
If there is not a digital signal present, but there
is an analog signal present, the analog signal
will be played.
Select “DIG”, when only a digital signal will be
used. Select “ANA” for input sources for which
no digital input jacks are used.
4.
5.
Select “SPEAKER SETUP” in SETUP MAIN
MENU with 3 or 4 cursor button, and press the
ENTER button.
To select the vdieo source, select “HDMI” or
“COMP” by pressing the 3 or 4 cursor buttons,
and press the 1 or 2 cursor buttons to select
the vdieo source to be assigned .
After you complete this portion of the set up,
move the cursor to MAIN with the 3 or 4 cursor
buttons and press the ENTER button.
To select the each speaker, press the 3 or 4
cursor buttons.
2.
To select the setting of each speaker size,
press the 1 or 2 cursor buttons.
3.
After you complete this portion of the set up,
move the cursor to “NEXT” with the 3 or 4
cursor buttons and then press the ENTER
button to go to the next page.
SUBWOOFER:
YES:
Select when a subwoofer is connected.
NONE:
Select when a subwoofer is not connected.
2-1 SPEAKER SETUP
Speakers are set up by selecting either MANUAL
or AUTO using the 1 and 2 cursor buttons. For
operation when AUTO has been selected, see
MRAC on page 29.
2-1 SPEAKER SETUP
1-2 INPUT SETUP
MAIN
1.
1.
FRONT L/R
LARGE:
Select if the front speakers are large.
SMALL:
Select if the front speakers are small.
• If “NONE” is selected for the Subwoofer setting,
then this setting is fixed to “LARGE.”
SPEAKER SETUP : MANUAL
MAIN
NEXT
EXIT
2-2 SPEAKERS SIZE
When setting the speaker size in the SPEAKER SIZE
sub-menu, use the guidelines given below.
LARGE:
The complete frequency range for the channel you
are setting will be output from the speaker.
SMALL:
Frequencies of the channel you are setting lower
than approx. 100 Hz will be output from the
subwoofer.
If the Subwoofer is set to “NONE”, the setting of
the front speakers will be fixed to “LARGE,” and
the sound will be output from both the left and
right speakers.
2-2 SPEAKERS SIZE
SUBWOOFER
: YES
FRONT L/R
: LARGE
CENTER
: SMALL
SURROUND L/R
: SMALL
SURR.BACK
: 2CH
SURR.BACK SIZE
: SMALL
LPF/HPF
: 100Hz
BASS MIX
: BOTH
MAIN
NEXT
EXIT
CENTER
NONE:
Select if no center speaker is connected.
LARGE:
Select if the center speaker is large.
SMALL:
Select if the center speaker is small.
SURROUND L/R
NONE:
Select if no surround left and right speakers are
connected.
LARGE:
Select if the surround left and right speakers are
large.
SMALL:
Select if the surround left and right speakers are
small.
SURR. BACK
NONE:
Select if no surround back left and right speakers
are connected.
2CH:
Select if the surround back left and right speakers
are connected.
1CH:
Select if the one surround back speaker is
connected.
In this case, the audio signal is emitted form the
Surround back L output terminal.
28
SR4002-5002U DFU_01_E2_2.indd 28
07.7.9 2:47:31 PM
SURR. BACK SIZE
LARGE:
Select if the surround back speaker is large.
SMALL:
Select if the surround back speaker is small.
Note:
If “NONE” is selected for the Surround L/R setting,
then this setting is not available.
LPF/HPF
When you use a subwoofer, you can select the cutoff
frequency for the small speakers used. Select one of
the crossover frequency levels according to the size
of the small speaker connected.
80Hz → 100Hz → 120Hz → 150Hz → 180Hz
2-3 SPEAKERS DISTANCE
Use this parameter to specify the distance of each
speaker’s position from the listening position. The
delay time is automatically calculated according to
these distances.
Begin by determining the ideal or most commonly
used seating position in the room.
This is important for the timing of the acoustics to
create the proper sound space that the unit and
today’s sound systems are able to produce.
Note:
For speakers that you have selected “NONE” the
Speaker Configuration sub-menu will not appear
here. (There are several useful books and special
DVD and LD’s available to guide you through proper
home theater configuration. If you are unsure, have
your Marantz dealer perform the installation for you.
They are trained professionals familiar with even
the most sophisticated custom installations. Marantz
recommends the WWW.CEDIA.ORG website for
further information about this).
2-3 SPEAKERS
DISTANCE UNIT
FRONT L
FRONT R
CENTER
SURR.L
SURR.R
SUB W
SURR.B L
SURR.B R
MAIN
RETURN
Notes:
• If using small front speakers, set a slightly higher
frequency. If using large front speakers, set a slightly
lower frequency.
• If Pure-Direct mode, 7.1CH Input is in use, this
function does not take effect.
BASS MIX
• The bass mix setting is only valid when “LARGE”
is set for the front speakers and “YES” is set for the
subwoofer during stereo playback .
This setting has effect only during playback of
PCM or analog stereo sources.
• When “BOTH” is selected, the low frequencies will
be played through the main L&R, as well as the
sub woofer.
In this playback mode, the low frequency range
expand more uniformly through the room, but
depending on the size and shape of the room,
interference may result in a decrease of the actual
volume of the low frequency range.
• By selecting “MIX”, the low frequencies will play
through the main L&R ONLY.
Note:
LFE signals during playback of Dolby Digital or DTS,
will be played through the sub woofer.
1.
DISTANCE
: ft
: 10.0 ft
: 10.0 ft
: 10.0 ft
: 10.0 ft
: 10.0 ft
: 10.0 ft
: 10.0 ft
: 10.0 ft
NEXT
EXIT
To select each speaker , press the 3 or 4
cursor buttons.
2.
To set the distance for each speaker , press the
1 or 2 cursor buttons.
3.
After you complete this portion of the set up,
move the cursor to “NEXT” with the 3 or 4
cursor buttons and then press the ENTER
button to go to the next page.
FRONT L:
Set the distance from the front left speaker to your
normal listening position.
CENTER:
Set the distance from the center speaker to your
normal listening position.
FRONT R:
Set the distance from the front right speaker to
your normal listening position.
SURR. L:
Set the distance from the surround left speaker to
your normal listening position.
SURR. R:
Set the distance from the surround right speaker
to your normal listening position.
SUB W:
Set the distance from the subwoofer to your
normal listening position.
SURR. B L:
Set the distance from the surround back left
speaker to your normal listening position.
SURR. B R:
Set the distance from the surround back right
speaker to your normal listening position.
Notes:
• Set the distance to each speaker in meters (m) or feet
(ft) as follows.
m: 0.1 - 9 m in 0.1 m steps
ft: 0.3 - 30 ft in 0.3 ft steps
• For the speakers that you have selected “NONE” the
Speaker Size menu will not appear.
• The setting for Surr.Back L and Surr.Back R appears
if you set for it to, two surround back speakers in the
Speaker Size menu.
• The setting of Surr.Back appears if it is set for one
surround back speaker in the Speaker Size menu.
2-4. SPEAKERS LEVEL SETTING WITH TEST TONE
Here you will set the volume for each speaker so that
they are all heard by the listener at the same level.
We recommend using a SPL (Sound Pressure Level)
meter, when available.
Note:
The speaker level settings are not available in 7.1
Channel Input mode, CS mode and Multi Channel
Stereo mode.
2-4 SPEAKERS
TEST MODE
FRONT L
CENTER
FRONT R
SURR.R
SURR.B R
SURR.B L
SURR.L
SUB W
MAIN
RETURN
LEVEL
:
MANUAL
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
EXIT
TEST MODE :
Selects “MANUAL” or “AUTO” for generating
the mode of the test tone with the 1 or 2 cursor
buttons.
If you select “AUTO” , the test tone will be cycled
through in a circular pattern which is Left → Center →
Right → Surround Right → Surround Back Right →
Surround Back Left → Surround Left → Subwoofer
→ Left → .. increments of 2 seconds
for each channel.
Using the 1 or 2 cursor buttons, adjust the volume
level of the noise from the speaker so that it is the
same level for all the speakers.
ENGLISH
Notes:
• If “NONE” is selected for the Surround L/R setting,
then this setting is fixed to “NONE.”
• You can use surround back speaker terminals as
multi room speaker terminals when you use no
surround back speaker. (See page 22)
If you select “MANUAL”, adjust the output level of
each speaker as listed below.
1.
When you move the cursor to FRONT L by
pressing the 4 cursor button, the unit will emit
a pink noise from the front left speaker.
Remember the level of this noise and then
press the 4 cursor button.
(Note that this can be adjusted to any level
between -10 and +10 dB in 1 dB intervals
except the subwoofer setting. The subwoofer
can be adjusted to any level between -15 and
+10 dB in 1 dB intervals.)
The unit will now emit the pink noise from the
center speaker.
2.
Using the 1 and 2 cursor buttons, adjust the
volume level of the noise from the center
speaker so that it is the same level as the front
left speaker.
3.
Press the 4 cursor button again. The unit will
now emit the pink noise from the front right
speaker.
4.
Repeat steps 2 and 3 above for the front
right and other speakers until all speakers are
adjusted to the same volume level.
After you complete this portion of the set up, press
the ENTER button, the cursor will move to “MAIN”
and then press the ENTER button to go to SETUP
MAIN MENU.
Notes:
• Speakers that you selected “NONE” for in the
Speaker Size menu will not appear.
• The setting of Surr.Back L and Surr.Back R appears
if you have set it for two surround back speakers in
the Speaker Size menu.
• The setting of Surr.Back appears if you have set it for
one surround back speaker in the Speaker Size menu.
• To adjust the speaker levels for 7.1-channel input
sources, you will need to use the 7.1CH-INPUT sub
menu. (See page 31).
29
SR4002-5002U DFU_01_E2_2.indd 29
07.7.9 2:47:32 PM
ENGLISH
MRAC (Marantz Room Acoustic Calibration)
Speaker settings that were difficult by MANUAL setup can now be made by automatically measuring speaker
characteristics using the including microphone.
AUTO SETUP
2-1 SPEAKER SETUP
START
CANCEL
MIC SETUP ERROR
SPEAKER SETUP : AUTO
NG
SET MICROPHONE
SPEAKERS
SPEAKERS
SPEAKERS
SPEAKERS
MAIN
NEXT
MAIN
EXIT
CHECK
LEVEL
DISTANCE
SIZE
RETURN
:
:
:
:
NEXT
EXIT
AUTO SETUP
START
SPEAKERS
SPEAKERS
SPEAKERS
SPEAKERS
• About surround back speakers :
When the surround back speaker is set to NONE in
the SPEAKER SETUP, it is skipped in the AUTO
setup. To use the surround back speaker, set it to
YES by MANUAL setup before using the MRAC
feature.
• The MRAC feature is available except in the
following modes.
- 7.1 CH INPUT
- PURE-DIRECT
- SOURCE DIRECT
3.
How to Operate
Settings are displayed on the monitor during setup,
therefore turn the monitor on.
CANCEL
CHECK
LEVEL
DISTANCE
SIZE
Measurement
During measurement, a test tone is output from the
speakers, which is then measured and analyzed
though the microphone. The measurement flow and
items are as follows.
Microphone connection check:
MIC CHECK
Ambient noise measurement:
AMBIENT NOISE
Speaker connected/not connected check:
SPEAKER CHECK
Speaker output level check:
SPEAKER LEVEL
Distance from speaker (delay time) check:
SPEAKER DISTANCE
Speaker characteristics check:
SPEAKER SIZE
:
:
:
:
1.
Connect the included microphone to the MRAC
jack of the unit.
2-1 SPEAKER SETUP
SPEAKER SETUP : AUTO
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
MAIN
RETURN
VOLUME
EXIT
DOWN
AUTO SETUP
AUTO SETUP
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
POWER ON/STANDBY
START
CANCEL
AMBIENT NOISE CHK
SPEAKERS
SPEAKERS
SPEAKERS
SPEAKERS
MAIN
CHECK
LEVEL
DISTANCE
SIZE
RETURN
EXIT
SPEAKERS
SPEAKERS
SPEAKERS
SPEAKERS
MAIN
CHECK
LEVEL
DISTANCE
SIZE
RETURN
NEXT
SET MICROPHONE
ATT
SETUP MIC
PHONES
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
4.
EXIT
2.
START
CANCEL
AMBIENT NOISE OK
MAIN
T-MODE
MAIN
&&&&&&&&&&&&&&&&
CHECK
LEVEL
DISTANCE
SIZE
CLEAR
BAND
:
:
:
:
AUTO SETUP
SPEAKERS
SPEAKERS
SPEAKERS
SPEAKERS
MEMORY
EXIT
ENTER
MENU
START
CANCEL
AMBI NOISE ERROR
NG
:
:
:
:
DISPLAY
UP
MUTE
STANDBY
Set the microphone at ear height as in the
actual listening position. Use a stand or tripod
to position the microphone.
Select START on the AUTO SETUP display
and press the ENTER button to star t
measurements.
SPEAKERS
SPEAKERS
SPEAKERS
SPEAKERS
MAIN
RETURN
SPEAKERS
SPEAKERS
SPEAKERS
SPEAKERS
EXIT
START
CANCEL
FINISHED
RETURN
NEXT
:
:
:
:
RETURN
NEXT
EXIT
NG
AUTO SETUP
MAIN
CHECK
LEVEL
DISTANCE
SIZE
START
CANCEL
SPEAKER SET ERROR
>&&&&&&&&&&&&&&&&
SPEAKERS CHECK
:
SPEAKERS LEVEL
:
SPEAKERS DISTANCE
:
SPEAKERS SIZE
:
CHECK
LEVEL
DISTANCE
SIZE
CANCEL
AUTO SETUP
START
CANCEL
NOW ANALYZING
SPEAKERS
SPEAKERS
SPEAKERS
SPEAKERS
EXIT
AUTO SETUP
EXIT
AUTO SETUP
MAIN
NEXT
START
:
:
:
:
RETURN
Select “2. SPEAKER SETUP” on the SETUP
MAIN MENU, then select AUTO for “21 SPEAKER SETUP”. Move the cursor to
“NEXT” with the 3 or 4 cursor buttons and then
press the ENTER button.
:
:
:
:
OK
OK
OK
OK
EXIT
MAIN
CHECK
LEVEL
DISTANCE
SIZE
RETURN
NEXT
:
:
:
:
EXIT
Notes:
• Remove any obstructions between the speakers and
the microphone.
• Keep the room quiet during measurement.
• The test tone emitted during measurement is loud.
Take considerations for neighboring homes and
children.
• Step away from the listening position during
measurement and operate the unit with the remote
controller from outside the speaker path.
5.
6.
For measurement items, see “Measurement”.
7.
Once finished, disconnect the microphone
from the unit.
8.
Measurement results can be seen by selecting
“NEXT” and press the ENTER button or
selecting “2. SPEAKER SETUP” on the SETUP
MAIN MENU. Then select MANUAL for “2-1
SPEAKER SETUP”.
When measurements are completed,
“FINISHED” appears on the monitor.
30
SR4002-5002U DFU_01_E2_2.indd 30
07.7.9 2:47:32 PM
Error Indications During Measurement
If trouble occurs during measurement, an error
message is displayed on the monitor screen and
FL display. Those errors and their remedies are
described below. The message appearing on the FL
display is given in ( ).
MIC SETUP ERROR (MIC SET ERROR)
The microphone (MC-10) is not properly connected.
→ Check the microphone connection.
AMBI NOISE ERROR (AMBI NOISE ER)
Measurement cannot be done correctly because of
excessive ambient noise.
→ Either temporarily turn off power to noisy
devices such as air conditioning or move them
out of the room.
→ Retry measurement when the room is quiet.
SPEAKER SET ERROR (SPK SET ERROR)
The speakers are not properly connected.
→ Recheck speaker layout and connections.
3 PREFERENCE
3 PREFERENCE
STANDBY MODE
TV-AUTO
OSD INFO
: ECONOMY
:
: ENABLE
VIDEO CONVERT
HDMI
: ENABLE
DC TRIGGER
MAIN
EXIT
1.
Select “PREFERENCE” in the SETUP MAIN
MENU with the 3 or 4 cursor buttons, and
press the ENTER button.
2.
To select a desired content, press the 3 or 4
cursor buttons.
STANDBY MODE:
When this function is set to “ECONOMY”, you can
reduce the power consumption when the unit is in
the standby mode.
Note:
TV-AUTO and RS-232C are disabled in the
“ECONOMY” setting (SR5002 only).
TV AUTO:
Select the TV AUTO ON/OFF function to enable or
disable with the 1 or 2 cursor buttons.
OSD Info:
Select the OSD information function to enable or
disable with the 1 or 2 cursor buttons.
If you select “ENABLE”, the unit will display the
status of the feature (Volume up/down, input
select, etc..) on the TV monitor. But if you do not
desire this information, select “DISABLE”.
VIDEO CONVERT:
Select the VIDEO CONVERT function to enable or
disable with the 1 or 2 cursor buttons. (Video cable
connection: Refer to page 20)
3-1 VIDEO CONVERT
TV
DVD
VCR
DSS
AUX1
:
:
:
:
:
3-2 DC TIRGGER SETUP
DC TRIG
DISABLE
TV
DVD
VCR
DSS
AUX1
:
:
:
:
:
MAIN RETURN
TAPE :
CD/R :
AUX2 :
TUNER:
7.1CH:
EXIT
You can select MAIN ROOM, MULTI ROOM,
REMOTE or DISABLE by pressing 1 or 2 cursor
buttons.
Notes:
• REMOTE is available for the external control. The
RC5001SR cannot operate this function.
• To select desired input source , press 3 or 4 cursor
button.
• To set ON or OFF, press 1 or 2 cursor button.
• After you complete this portion of the set up, move
the cursor to “MAIN” with the 3 or 4 cursor
buttons and press the ENTER button.
4 SURROUND
4 SURROUND
SURR.MODE :AUTO
HT-EQ
:OFF
LFE LEVEL :
MAIN
EXIT
1.
Select “SURROUND” in the SETUP MAIN
MENU with the 3 or 4 cursor buttons, and
press the ENTER button.
2.
To select a desired content , press the 3 or 4
cursor buttons.
SURR.MODE:
Select the desired surround mode with the 1 or 2
cursor buttons.
HT-EQ:
Select to active the HT-EQ with the 1 or 2 cursor
buttons.
The tonal balance of a film soundtrack will be
excessively bright and harsh when played back
over audio equipment in the home. This is because
film soundtracks were designed to be played back
in large movie theater environments.
Activating the HT-EQ feature when watching a film
made for movie theaters corrects this and restores
the correct tonal balance.
The HT-EQ feature is available except in the
following modes.
• 7.1 CH INPUT
• PURE-DIRECT
• SOURCE DIRECT
• When VIRTUAL is set for the surround mode
LFE LEVEL:
Select the output level of the LFE signal included in
the Dolby Digital signal or the DTS signal.
Select 0 dB, -10 dB or OFF with the 1 or 2 cursor
buttons.
After you complete this portion of the set up, move
the cursor to “MAIN” with the 3 or 4 cursor buttons
and press the ENTER button.
ON
ON
ON
ON
ON
MAIN RETURN
HDMI AUDIO:
This setting determines whether to playback audio
input to the HDMI jacks through the unit or output
it through the unit to a TV or projector.
ENABLE: The audio input to the HDMI jacks
can be played back by this unit.
In such case, audio signals are not
output to the TV or projector.
THROUGH: The audio input to the HDMI jacks
is not output from the speaker
terminals of the unit. Audio data is
output directly to the TV or projector.
This setting is used to listen to audio
on a multi channel TV, etc.
DC TRIGGER:
Select “DC TRIG SETUP” in the SETUP MAIN
MENU with 3 or 4 cursor button, and press the
ENTER button.
ENGLISH
Notes:
• If MRAC is started with both speaker settings A
and B off, it will enter CANCEL mode without
displaying an ERROR on the screen. When this
happens, check the SPEAKER setting.
• The measured speaker distance may differ from the
actual distance from speakers. Nevertheless, the
measured value is suitable for the speakers.
• To make changes to individual speakers, select 2.
SPEAKER SETUP on the SETUP MAIN MENU,
then select MANUAL for 2-1 SPEAKER SETUP.
• The included microphone is designed specifically for
this receiver. Other microphones do not guarantee
suitable measurement results. Use the included
microphone to conduct measurements.
• During measurement, press the ENTER or EXIT
button to cancel measurement.
• In some rooms, an error may occur during auto
speaker setup or it may not be possible to set Speaker
distance correctly because of room acoustics. In
such case, set the speaker distance by MANUAL
setup.
• Please set any THX Certified speakers manually
to “Small” and the crossover to “80 Hz” after Auto
setup operation.
• When only HDMI components are connected, OSD
will not be displayed.
EXIT
After you complete this portion of the set up, move
the cursor to “MAIN” with the 3 or 4 cursor buttons
and press the ENTER button.
31
SR4002-5002U DFU_01_E2_2.indd 31
07.7.9 2:47:33 PM
ENGLISH
5 PL II (PRO LOGIC II)
MUSIC PARAMETER
6 CS II (CIRCLE SURROUND II) PARAMETER
6 CSII PARAMETER
Pro Logic II-Music mode creates a rich and enveloping
surround ambience from stereo sources such as
CDs.
In this mode, SR4002/SR5002 includes three controls
to fine-tune the soundfield as follows.
TRUBASS
SRS DIALOG
: 0
: 0
7 7.1 CH INPUT LEVEL
This sub-menu is to adjust the speaker levels for 7.1channel input sources.
Here you will adjust the volume for each channel so
that they are all heard by the listener at the same
level.
SR5002 has features in MULTI ROOM SYSTEM
such as source selector, sleep timer, Multi Room
Speaker output and remote control.
You can set these feature in this sub-menu.
7 7.1 CH. INPUT LEVEL
VIDEO-IN
:
LAST
FRONT L
:
0 dB
CENTER
:
0 dB
FRONT R
:
0 dB
SURR.R
:
0 dB
SURR.B R
:
0 dB
SURR.B L
:
0 dB
SURR.L
:
0 dB
SUB W
:
0 dB
MAIN
EXIT
AUDIO
: DVD
SLEEP TIMER
: OFF
MULTI:OUT
: STEREO
MULTI:OFF
MSPK
:
VOL
: VARI
LEVEL
: -90dB
--- MAIN ROOM STATUS --VIDEO:DVD
AUDIO:DVD
MAIN
RETURN
EXIT
5 PLIIx MUSIC PARAMETER
MAIN
PARAMETER
MAIN
1.
EXIT
Select “PL II MUSIC” in the SETUP MAIN MENU
with the 3 or 4 cursor buttons, and press the ENTER
button.
PARAMETER:
Select “DEFAULT” or “CUSTOM” with the 1 or 2
cursor buttons.
If you select “CUSTOM”, you can adjust three
parameters as listed below.
PANORAMA:
Select the Panorama mode On or Off with the
1 or 2 cursor buttons.
Panorama wraps the sound of the front left and right
speakers around you, for an exciting perspective.
DIMENSION:
Set the Dimension level between +3 and –3 level in
1 level intervals with the 1 or 2 cursor buttons.
Adjust the soundfield either towards the front or
towards the rear.
This can be useful to help achieve a more
suitable balance from all the speakers with certain
recordings.
CENTER WIDTH:
Set the Center width level between 0 and 7 in 1
level intervals with the 1 or 2 cursor buttons.
Center Width allows you to gradually spread the
center channel sound into the front left and right
speakers.
At its widest setting, all the sound from the center
is mixed into the left and right.
This control may help achieve a more spacious
sound or a better blend for the front image.
If “NONE” was selected for the Center speaker
setting, in the Speaker size set up menu, then this
setting will not appear.
After you complete this portion of the set up, move
cursor to “MAIN” with the 3 or 4 cursor buttons and
press the ENTER button.
32
SR4002-5002U DFU_01_E2_2.indd 32
EXIT
: DEFAULT
PANORAMAA
: OFF
DIMENSION
:
0
CENTER WIDTH :
3
Select “CS II” in the SETUP MAIN MENU
with the 3 or 4 cursor buttons, and press the
ENTER button.
2.
To Select desired contents as below, press the
3 or 4 cursor buttons.
TRUBASS:
Set the TRUBASS level between 0 and 6 level in 1
level interval with the 1 or 2 cursor buttons.
TRUBASS produced by the speakers are an octave
below the actual physical capabilities of the speakers
adding exciting, deeper bass effects.
SRS DIALOG:
Set the SRS DIALOG level between 0 and 6 in 1
level intervals with the 1 or 2 cursor buttons.
This can be popped out of the surround audio
effects, allowing the listener to easily discern what
the actors say.
If “NONE” was selected for the Center speaker
setting, in the Speaker size set up menu, then this
setting will not appear.
After you complete this portion of the set up, move
cursor to “MAIN” with the 3 or 4 cursor buttons and
press the ENTER button.
8 MULTI ROOM (SR5002 only)
1.
Select “7.1CH INPUT” in the SETUP MAIN
MENU with the 3 or 4 cursor buttons, and
press the ENTER button.
2.
To select “VIDEO IN”, press 3 or 4 cursor
button.
3.
Using the 1 or 2 cursor buttons, select the
video input source which is emitted from
Monitor out in the 7.1 CH INPUT function.
The input source is switched by pressing the
1 or 2 cursor buttons as follows;
LAST ↔ TV ↔ DVD ↔ VCR ↔ DSS ↔ AUX1
↔ V-OFF ↔ LAST ↔
Notes:
• When select LAST, the source is set previous source
before 7.1 CH INPUT function is activated.
• When select V-OFF, no signal is emitted from monitor
out terminal.
4.
To Select desired channel , press the 3 or 4
cursor buttons.
5.
Using the 1 or 2 cursor buttons, adjust the
volume level of each channel.
6.
After you complete this portion of the set up,
move the cursor to “MAIN” with the 3 or 4
cursor buttons and press the ENTER button.
Notes:
• These settings will be memorized to 7.1CH INPUT
source.
• This feature can be directly selected with the
CH.SEL button of the remote controller.
8 MULTI ROOM
1.
Select “MULTI ROOM” in the SETUP MAIN
MENU with 3 or 4 cursor button, and press the
ENTER button.
2.
To Select desired contents, press 3 or 4 cursor
button
AUDIO:
Select the audio source of the Multi-room output
with 1 or 2 cursor buttons.
SLEEP TIMER:
SLEEP timer function is available during the
multiroom is active, set the time with 1 or 2 cursor
buttons.
MULTI OUT:
To switch MULTI and MSPK outputs to either
STEREO or MONO, press 1 or 2 cursor button.
MULTI (MULTI ROOM):
To switch on the Multi-room output ON or OFF,
press 1 or 2 cursor button.
VOL (VOLUME SETUP):
Select whether the Multi-room output level is
variable or fixed with a 1 or 2 cursor buttons.
LEVEL (VOLUME LEVEL):
Adjust the Multi-room output level with 1 or 2
cursor buttons.
MSPK (MULTI SPEAKER):
To switch on the Multi-speaker output ON or OFF,
press 1 or 2 cursor buttons.
Note:
This setting can be changed when the Surr Back is set
“NONE” in 2-1 SPEAKER SIZE menu. When this
setting is unavailable, “✽✽✽” is displayed
MAIN ROOM STATUS:
Selected input source in the main room will be
displayed.
Note:
If “VOLUME” is set to “FIXED”, the multi-room
output level cannot be adjusted from the second zone.
After you complete this portion of the set up, move
the cursor to “MAIN” with 3 or 4 cursor buttons and
press ENTER button.
07.7.9 2:47:33 PM
You can setup the speaker conditions quickly with
SIMPLE SETUP menu. In this menu, the number
of speakers and speaker delay time can be set.
These settings can be changed more detail in “2.
SPEAKER” setup menu.
Press the SIMPLE SETUP button on the unit to enter
this menu.
1. 2. 4. 3. 5.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
VOLUME
DOWN
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
1.
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
MUTE
STANDBY
POWER ON/STANDBY
UP
ATT
ENTER
SETUP MIC
MENU
DIGITAL
PHONES
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
Press the SIMPLE SETUP button on the unit to
enter the “SPEAKERS” menu.
2.
Press 1 or 2 cursor button to select the speaker
number.
3.
Press the 4 cursor button to enter the “ROOM”
menu.
4.
Press 1 or 2 cursor button to select the room
size.
5.
After finishing all setup, press the 4 cursor
button to exit the SIMPLE SETUP menu.
CHANNEL
7.1 ch
7.0 ch
6.1 ch
6.0 ch
5.1 ch
5.0 ch
4.1 ch
4.0 ch
3.1 ch
3.0 ch
2.1 ch
2.0 ch
Front
L/R
(F)
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
Front Surround Surround
Back L/R
L/R
Center
(SB)
(S)
(C)
SMALL SMALL
2ch
SMALL SMALL
2ch
SMALL SMALL
1ch
SMALL SMALL
1ch
SMALL SMALL
NONE
SMALL SMALL
NONE
NONE SMALL
NONE
NONE SMALL
NONE
SMALL NONE
NONE
SMALL NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
The relation of the room size and floor space
SIZE
Floor
space
Width
(W)
Depth
(D)
SMALL
10 m2
2.7 m
3.6 m
MEDIUM
16 m2
3.6 m
4.5 m
LARGE
24 m2
4.5 m
5.4 m
Note:
All Simple Setup menu is reset when the speaker
setting is changed with Speaker Setup menu.
SIMPLE SETUP
1.SPEAKERS : ?
2.ROOM
MAIN
Imaging Distance
Front (F)
Center (C)
Surround (S)
Surr. Back (SB)
Sub Woofer (SW)
Front (F)
Center (C)
Surround (S)
Surr. Back (SB)
Sub Woofer (SW)
Front (F)
Center (C)
Surround (S)
Surr. Back (SB)
Sub Woofer (SW)
6 ft. (1.8 m)
5 ft. (1.5 m)
4 ft. (1.2 m)
5 ft. (1.5 m)
5 ft. (1.5 m)
7 ft. (2.1 m)
6 ft. (1.8 m)
5 ft. (1.5 m)
7 ft. (2.1 m)
6 ft. (1.8 m)
9 ft. (2.7 m)
8 ft. (2.4 m)
7 ft. (2.1 m)
8 ft. (2.4 m)
8 ft. (2.4 m)
The relation of the room size and floor space is a
roughly standard.
: ?
RETURN
Sub
woofer
(SW)
YES
NONE
YES
NONE
YES
NONE
YES
NONE
YES
NONE
YES
NONE
ENGLISH
The relation of the speakers number and
conectted speaker
SIMPLE SETUP
EXIT
33
SR4002-5002U DFU_01_E2_2.indd 33
07.7.9 2:47:34 PM
ENGLISH
BASIC OPERATION
SELECTING THE SURROUND MODE
ADJUSTING THE MAIN VOLUME
Example: AUTO SURROUND
(PLAYBACK)
VOLUME
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
DOWN
SLEEP
SELECTING AN INPUT SOURCE
Before you can listen to any input media, you must
first select the input source on the unit.
1
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
AUTO
POWER ON/STANDBY
Example : DVD
SETUP MIC
HT-EQ
2
3
EX/ES
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
CS
SIMPLE
SETUP
STANDBY
DISC+
ANGLE
SUB TITLE
V-OFF
ATT.
CH-SEL
BASS
CL
AUDIO
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
TREBLE
TV
DVD
VCR
TUNER
CD
CDR
DSS
MD
TAPE
AUX1
AUX2
AMP
STANDBY
POWER ON/STANDBY
SETUP MIC
PHONES
MENU
SPKR A/B
VOLUME
CL
AUTO
CS
4
M-CH ST
7
CL
CH/ CAT
MUTE
BAND
A/D
0
+10
HT-EQ
MEMO
VOLUME
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
UP
CLEAR
T-MODE
ATT
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
INFO
R
MENU
ISPLAY
MEMORY
CLEAR
BAND
T-MODE
MUTE
EXIT
DIGITAL
8
P.SCAN
ATT
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
INFO
R
MENU
dts
2
3
EX/ES
VIRTUAL
5
6
A/D
HT-EQ
0
+10
MEMO
STEREO
NIGHT
LIP SYNC/
INPUT
T.MODE
P.SCAN
8
9
7.1CH IN
A/D
HT-EQ
0
+10
MEMO
SPKR A/B
MUTE
ENTER
9
7.1CH IN
To select the surround mode during playback, press
the SURROUND MODE button on the front panel
or the SURROUND MODE buttons on the remote
controller.
1
MEMORY
7.1CH IN
M-SPKR
DOWN
SPLAY
DIGITAL
NIGHT MODE
• As the input source is changed, the new input
name will appear momentarily an OSD information
on the video display. The input name will also
appear in the display, on the front-panel.
• As the input is changed, this unit will automatically
switch to the digital input, surround mode,
attenuation, and night mode status which were
entered during the configuration process for that
source.
• When an audio source is selected, the last video
input used remains routed to the VCR Output
and Monitor Output. This permits simultaneous
viewing and listening to different sources.
• When a Video source is selected, the video
signal for that input will be routed to the Monitor
Output jacks and will be viewable on a TV monitor
connected to the unit.
If a component video input is connected to the
DVD or DSS component inputs, it will be routed
to the Component Video Output. Make certain
that your TV is set to the proper input to view the
signal.
MUTE
UP
CH/ CAT
EXIT
REMOTE CONTROLLER
To select DVD, turn the INPUT SOURCE knob on
the front panel or simply press the DVD button on the
remote controller.
After you have selected DVD, simply turn on the DVD
player and play the DVD.
HT-EQ
MEMO
VOLUME
MENU
PHONES
7
SURROUND
MODE
+10
T.MODE
INPUT SELECTOR
MULTI
SPEAKER
A/D
0
MULTI/ CAT
AUTO
MULTI
7.1CH IN
l/
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
AV SURROUND RECEIVER SR5002
CL
CH/ CAT
TEMPORARILY TURNING OFF
THE SOUND
VOLUME
ENTER
Adjust the volume to a comfortable level using
the VOLUME control knob on the front panel or
VOLUME 3 / 4 buttons on the remote controller.
To increase the volume, turn the VOLUME knob
clockwise or press VOLUME 3 button on the
remote controller, to decrease the volume, turn
counterclockwise or press VOLUME 4 button on the
remote controller.
To temporarily silence all speaker outputs such as
when interrupted by a phone call, press the MUTE
button on the front panel or MUTE button on the
remote controller.
This will interrupt the output to all speakers and the
head-phone jack, but it will not affect any recording or
dubbing that may be in progress.
When the system is muted, the display will show
Notes:
• The volume can be adjusted within the range of – ∞ “MUTE” .
Press the MUTE button again to return to normal
to 18 dB, in steps of 1 dB.
operation.
• However, when the channel level is set as described
on page 26, if the volume for any channel is set at +1
dB or greater, the volume cannot be adjusted up to 18
dB.
USING THE SLEEP TIMER
(In this case the maximum volume adjustment range is
“18 dB - Maximum value of channel level)
LEARN
Press the NIGHT button on the remote controller to
turn on the NIGHT mode.
Selecting the Night Mode ON is effective in Dolby
Digital only, and it compresses the dynamic range.
This softens loud passages such as sudden
explosions, to help prevent disturbing others late at
night.
To turn off the Night mode, press the NIGHT button
again.
ADJUSTING THE TONE (BASS & TREBLE)
CONTROL
SOURCE
PRESET
+
-
TUNING
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
-
AUTO
+
1
CS
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
TV
DVD
VCR
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
BASS
AUDIO
TREBLE
REMOTE CONTROLLER
SEND
4
2
3
EX/ES
VIRTUAL
5
6
T.MODE
To program this unit for automatic standby, press the
SLEEP button on the remote controller.
Each press of the button will increase the time before
shut down in the following sequence.
OFF
120
10
110
20
100
40
30
90
80
70
50
60
During a listening session you may wish to adjust the
Bass and Treble Control to suit your listening tastes The sleep time will be shown for a few seconds in the
display on the front panel, and it will count down until
or room acoustics.
the time has elapsed.
(Using the remote controller)
When the programmed sleep time has elapsed, the
To adjust the bass effect, press BASS 3 or BASS 4 unit will automatically turn off.
on the remote controller.
Note that the SLEEP indicator on the display will
To adjust the treble effect, press TREBLE 3 or illuminate when the Sleep function is programmed.
TREBLE 4 on the remote controller.
To cancel the Sleep function, press the SLEEP
Note:
button until the display shows “SLEEP OFF” and the
The tone control function can work in the AUTO SLEEP indicator will disappear.
Surround, Stereo, Dolby PLIIx, DTS, DTS-ES, and
Multi Ch. Stereo mode.
34
SR4002-5002U DFU_01_E2_2.indd 34
07.7.9 2:47:34 PM
When this function is activated, the video or
S-video signal can be emitted from the video, S-video
or component video output terminal.
To activate this function, select VIDEO CONVERT in
PREFERENCE menu and set ENABLE.
Notes:
• The component video signal is emitted only from
component video output terminal.
When the video equipment is connected by
component terminal, connect the monitor and
SR4002/SR5002 by the component terminal.
• This function is unavailable for the REC out
terminal.
• This function is unavailable for the still picture, fast
forward and reverse playing of the video component.
• If, while attempting to use the video convert feature,
the SR4002/SR5002 cannot synchronize with the
display device, “NO SIGNAL” appears on the
monitor, or noise is generated, this feature cannot
be used. All of these signs are caused by equipment
incompatibility; there is nothing wrong with the
SR4002/SR5002.
In such case, set VIDEO CONVERT in the
PREFERENCE menu to DISABLE. Also, connect
the video input signal to the display device via the
MONITOR OUT terminal under VIDEO and the
S-video input signal to the display device via the
MONITOR OUT terminal under S-VIDEO.
HDMI
Example:
Monitor is connected with the component.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
VOLUME
DOWN
MULTI
SPEAKER
MULTI
SR5002 only
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
MEMORY
UP
CLEAR
ATT
ENTER
AUTO
POWER ON/STANDBY
DISPLAY
MUTE
STANDBY
SETUP MIC
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
PHONES
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
VOLUME
DOWN
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
UP
MUTE
STANDBY
HDMI
VIDEO
S-VIDEO
component
ATT
ENTER
POWER ON/STANDBY
MENU
AUX 1 INPUT
S-VIDEO
VIDEO
DIGITAL
PHONES
SETUP MIC
L
AUDIO
R
ENGLISH
VIDEO CONVERT
component
VIDEO
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
Monitor is connected with the video or S-video.
VOLUME
DOWN
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
MEMORY
UP
CLEAR
MUTE
STANDBY
ATT
ENTER
AUTO
POWER ON/STANDBY
DISPLAY
SETUP MIC
PHONES
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
SR5002 only
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
VOLUME
DOWN
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
MEMORY
UP
CLEAR
MUTE
STANDBY
ATT
ENTER
AUTO
POWER ON/STANDBY
HT-EQ
MENU
EXIT
BAND
T-MODE
AUX 1 INPUT
S-VIDEO
VIDEO
DIGITAL
PHONES
SETUP MIC
VIDEO
L
AUDIO
R
S-VIDEO
Monitor is connected with the video or component.
SR4002/SR5002
VIDEO
S-VIDEO
component
HDMI
Notes of OSD menu:
HDMI: OSD menu is not displayed.
VIDEO/S-VIDEO/component: VIDEO CONVERT
of HDMI is not possible, thus the OSD menu is not
displayed.
AV SURROUND RECEIVER SR4002
INPUT SELECTOR
VOLUME
DOWN
SURROUND
MODE
7.1 CH INPUT
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
MEMORY
UP
CLEAR
S.SPEAKER B
MUTE
STANDBY
ATT
ENTER
AUTO
POWER ON/STANDBY
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
PHONES
SETUP MIC
S-VIDEO
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
VIDEO
component
SR4002/SR5002
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
VOLUME
DOWN
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
UP
MUTE
STANDBY
POWER ON/STANDBY
ATT
ENTER
SETUP MIC
PHONES
MENU
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
VIDEO
component
S-VIDEO
The signal cannot be converted from the component
to the video or S-video.
Notes of OSD menu:
• The setup menu can be displayed through all video
out (COMPONENT, S-VIDEO, VIDEO).
• The setting informations (e.g. volume setting) are
displayed through all video out when the VIDEO
CONVERT function are set ON.
Note:
No setting information is displayed when the
signal is emitted from the COMPONENT IN to
COMPONENT OUT.
• The setting informations (e.g. volume setting) are
displayed through the S-VIDEO or VIDEO out
when the VIDEO CONVERT function are set
DISABLE. When the S-VIDEO and VIDEO outputs
are used simultaneously, the setting informations are
displayed through the S-VIDEO out only.
35
SR4002-5002U DFU_01_E2_2.indd 35
07.7.9 2:47:35 PM
ENGLISH
SURROUND MODE
This unit is equipped with many surround modes. These are provided to reproduce a variety of surround sound effects, according to the content of the source to be played.
The available surround modes may be restricted depending on the input signal and speaker setup.
The relation between the selected surround mode and the input signal
The surround mode is selected with the surround mode selector on this unit or the remote controller. However, the sound you hear is subject to the relationship between the selected surround mode and input signal. That
relationship is as follows;
Surround
Mode
AUTO
SOURCE DIRECT
PURE DIRECT
EX/ES
DOLBY
(PL IIx movie)
(PL IIx music)
(PL IIx game)
(Pro Logic)
DTS
(Neo:6 Cinema)
(Neo:6 Music)
Output Channel
Input Signal
Decoding
Dolby Surr. EX
Dolby D (5.1ch)
Dolby D(2ch)
Dolby D (2ch Surr)
DTS-ES
DTS 96/24
DTS (5.1ch)
Multi Ch-PCM
Multi Ch-PCM 96kHz
PCM(Audio)
PCM 96kHz
HDCD
Analog
Dolby Surr. EX
Dolby D (5.1ch)
Dolby D (2ch)
Dolby D (2ch Surr)
DTS-ES
DTS 96/24
DTS (5.1ch)
Multi Ch-PCM
Multi Ch-PCM 96kHz
PCM (Audio)
PCM 96kHz
HDCD
Analog
Dolby Surr. EX
Dolby D (5.1ch)
DTS-ES
DTS 96/24
DTS(5.1ch)
Multi CH-PCM
AAC (5.1ch)
Dolby Surr. EX
Dolby D (5.1ch)
Dolby D (2ch)
Dolby D (2ch Surr)
Multi Ch-PCM
PCM (Audio)
Analog
DTS-ES
DTS 96/24
DTS (5.1ch)
PCM (Audio)
Analog
Dolby D (2ch)
Dolby D (2ch Surr)
Dolby Digital EX
Dolby Digital 5.1
Dolby Digital 2.0
Pro Logic IIx movie
DTS-ES
DTS 96/24
DTS 5.1
Multi Ch-PCM
Multi Ch-PCM 96kHz
PCM (Stereo)
PCM (96kHz Stereo)
PCM (Stereo)
Stereo
Dolby Digital EX
Dolby Digital 5.1
Dolby Digital 2.0
Pro Logic IIx movie
DTS-ES
DTS 96/24
DTS 5.1
Multi Ch-PCM
Multi Ch-PCM 96kHz
PCM (Stereo)
PCM (96kHz Stereo)
PCM (Stereo)
Stereo
Dolby Digital EX
Dolby Digital EX
DTS-ES
DTS-ES
DTS-ES
Multi Ch-PCM + Dolby EX
AAC EX
Dolby Digital 5.1
Dolby Digital 5.1
Pro Logic IIx
Pro Logic IIx
Multi Ch-PCM + PLIIx
Pro Logic IIx
Pro Logic IIx
DTS 5.1
DTS 96/24
DTS 5.1
Neo:6
Neo:6
Neo:6
Neo:6
L/R
C
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Front information display
SL SBL
Signal format indicators
SR SBR SubW
O
O
O 2 DIGITAL EX
O
O 2 DIGITAL
- 2 DIGITAL
O
O
O 2 DIGITAL , 2 SURROUND
O
O
O dts, ES
O
O dts 96/24
O
O dts
O
O PCM
O
O PCM
O PCM
O PCM
O PCM HDCD
O ANALOG
O
O
O 2 DIGITAL EX
O
O 2 DIGITAL
- 2 DIGITAL
O
- 2 DIGITAL , 2 SURROUND
O
O
O dts, ES
O
O dts 96/24
O
O dts
O
O PCM
O
O PCM
- PCM
- PCM
- PCM HDCD
- ANALOG
O
O
O 2 DIGITAL EX
O
O
O 2 DIGITAL
O
O
O dts , ES
O
O
O dts 96/24
O
O
O dts
O
O
O PCM
O
O AAC
O
*
O 2 DIGITAL EX
O
*
O 2 DIGITAL
O
O
O 2 DIGITAL
O
O
O 2 DIGITAL , 2 SURROUND
O
O
O PCM
O
O
O PCM
O
O
O ANALOG
O
O dts, ES
O
O dts 96/24
O
O dts
O
O
O PCM
O
O
O ANALOG
O
O
O 2 DIGITAL
O
O
O 2 DIGITAL , 2 SURROUND
Channel status
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, R, S
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, R
L, R
L, R
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, R, S
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, R
L, R
L, R
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, R, S
L, C, R, SL, SR, LFE
L, R
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, R
L, R
L, R, S
Surround
Mode
CS II Cinema
CS II Music
CS II Mono
STEREO
Virtual
Multi Ch.
Stereo
Output Channel
Input Signal
Decoding
PCM (Audio)
Analog
Dolby D (2ch)
Dolby D (2ch Surr)
Dolby Surr. EX
Dolby D (5.1ch)
Dolby D (2ch)
Dolby D (2ch Surr)
DTS-ES
DTS 96/24
DTS (5.1ch)
Multi Ch-PCM
PCM (Audio)
PCM 96kHz
HDCD
Analog
Dolby Surr. EX
Dolby D (5.1ch)
Dolby D (2ch)
Dolby D (2ch Surr)
DTS-ES
DTS (5.1ch)
Multi Ch-PCM
PCM (Audio)
Analog
Dolby Surr. EX
Dolby D (5.1ch)
Dolby D (2ch)
Dolby D (2ch Surr)
DTS-ES
DTS 96/24
DTS (5.1ch)
Multi Ch-PCM
Multi Ch-PCM 96kHz
PCM (Audio)
Analog
CS II
CS II
CS II
CS II
Stereo
Stereo
Stereo
Stereo
Stereo
Stereo
Stereo
Stereo
Stereo
Stereo
PCM (Stereo)
Stereo
Virtual
Virtual
Virtual
Virtual
Virtual
Virtual
Virtual
Virtual
Virtual
Dolby Digital EX
Dolby Digital 5.1
Multi Channel Stereo
Multi Channel Stereo
DTS-ES
DTS 96/24
DTS 5.1
Multi Ch-PCM
Multi Ch-PCM 96kHz
Multi Channel Stereo
Multi Channel Stereo
L/R
C
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Front information display
SL SBL
Signal format indicators
SR SBR SubW
O
O
O PCM
O
O
O ANALOG
O
O
O 2 DIGITAL
O
O
O 2 DIGITAL , 2 SURROUND
O 2 DIGITAL EX
O 2 DIGITAL
O* 2 DIGITAL
O* 2DIGITAL , 2 SURROUND
O dts, ES
O dts 96/24
O dts
O PCM
O PCM
O PCM
O PCM HDCD
O ANALOG
- 2 DIGITAL EX
- 2 DIGITAL
- 2 DIGITAL
- 2 DIGITAL , 2 SURROUND
- dts, ES
- dts
- PCM
- PCM
- ANALOG
O
O
O 2 DIGITAL EX
O
O 2 DIGITAL
O
O O* 2 DIGITAL
O
O O* 2 DIGITAL , 2 SURROUND
O
O
O dts, ES
O
O
O dts 96/24
O
O dts
O
O PCM
O
O PCM
O
O O* PCM
O
O O* ANALOG
Channel status
L, R
L, R
L, R, S
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, R, S
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, R
L, R
L, R
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, R, S
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, R
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, R
-
* : Depending on the particular setup, there may be differences compared to the information contained in
these tables.
O* : When L/R (FRONT Speaker) = SMALL.
Notes:
• Dolby Digital (2 ch: Lt/Rt): signal with Dolby
Surround flag Speakers are full set.
• No sound outputs from the surround speaker, center
speaker and subwoofer if the DVD disc has no
surround data.
Abbreviations
L/R :
C:
SL/SR :
SBL/SBR :
SubW :
Front speakers
Center speaker
Surround speakers
Surround Back speakers
Sub woofer speaker
36
SR4002-5002U DFU_01_E2_2.indd 36
07.7.9 2:47:36 PM
EX/ES
2 MODE
dts MODE
When this mode is selected, the unit determines
whether the digital input signal is Dolby Digital, Dolby
Digital Surround EX, DTS, DTS-ES, DTS 96/24 or
PCM-audio.
Surround EX & DTS-ES will operate for multichannel
source that has a Dolby Digital Surround EX or DTSES auto trigger flag in the digital signal.
When a Dolby Digital or DTS signal is input, the
number of channels for which the corresponding
signal is encoded will be played.
Inputting a Dolby Digital two channel signal with
Dolby surround status automatically subjects that
signal to Pro Logic IIx movie processing before play.
PCM 96 kHz source material can be played in this
mode.
This mode provides 6.1 channel surround for DOLBY
DIGITAL EX, DTS-ES encoded source material such
as DVD.
This mode cannot be used when an analog input has
been selected.
(Dolby Digital, Pro Logic IIx MOVIE, Pro Logic IIx
MUSIC, Pro Logic IIx GAME, Pro Logic)
This mode is used with source materials encoded in
Dolby Digital and Dolby Surround.
(dts, Neo:6 Cinema, Neo:6 Music)
This mode is for DTS encoded source materials such
as LASER DISC, CD, and DVD. Neo:6 is for some 2
channel sources.
Dolby Digital EX
In a movie theater, film soundtracks that have been
encoded with Dolby Digital surround EX technology
are able to reproduce an extra channel which has
been added during the mixing of the program.
This channel, called Surround Back, places sounds
behind the listener in addition to the currently
available front left, front center, front right, surround
right, surround left and subwoofer channels.
This additional channel provides the opportunity
for more detailed imaging behind the listener and
brings more depth, spacious ambience and sound
localization than ever before.
Dolby Digital EX is not available in the system without
surround back speaker(s).
DOLBY DIGITAL
This mode is enabled when playing source materials
encoded in Dolby Digital.
Playing multichannel encoded 6.1 or 7.1-channel
Dolby Digital sources provides five main audio
channels (left, center, right, surround left and
surround right) and Low Frequency Effect channel.
Dolby Digital EX decoding is not available in this
mode.
dts : This mode is enabled when playing source
materials encoded in dts multichannel.
Playing multichannel encoded 5.1-channel dts
sources provides five main audio channels (left,
center, right, surround left and surround right) and
Low Frequency Effect channel.
dts-ES decoding is not available in this mode.
The DTS mode cannot be used when an analog
input has been selected.
Dolby Pro Logic IIx brings the excitement of surround
sound to any stereo mix, while making existing
Dolby Surround mixes sound more like discrete 5.1
channels Surround sound.
Dolby Pro Logic IIx has 3 modes. Please see below.
Pro Logic IIx MOVIE
This mode provides 6.1 or 7.1 channel surround
sound from Dolby Surround encoded stereo movie
sound tracks.
Pro Logic IIx MUSIC
This mode provides 6.1 or 7.1 channel surround
sound from conventional stereo sources, analog or
digital, such as CD, Tape, FM, TV, Stereo VCR, etc.
Pro Logic IIx GAME
Game mode restores the impact low-frequency
surround effects by routing them to the system’s
subwoofer.
Pro Logic
This mode emulated original Dolby Pro Logic
decoding (3/1 surround) suit for Dolby Surround
encoded stereo movie soundtracks.
Neo:6 Cinema, Neo:6 Music
This mode decodes 2-channel signals into 6channel signals using high-accuracy digital matrix
technology.
The DTS NEO:6 decoder has near-discrete properties
in the frequency characteristics of the channels as
well as in channel separation.
According to the signals to be played back, DTS
NEO:6 uses either the NEO:6 CINEMA mode
optimized for movie playback or the NEO:6 MUSIC
mode optimized for music playback.
Notes:
• When you use this mode with certain DVD and CD
players, performing operations such as “Skip” or
“Stop” may momentarily interrupt the output.
• When the signal is not decoded, the mode is changed
to AUTO mode automatically. Refer to page 35 to
confirm the available decoding mode.
SOURCE DIRECT
In the Source Direct mode, the tone control circuit
and bass management configuration are bypassed
for full-range frequency response and the purist
audio reproduction.
Notes:
• Speaker size is set to Front L/R = LARGE, Center =
LARGE, Surround L/R = LARGE and Subwoofer
= YES automatically. Tone controls, equalizer and
additional processing are deactivated.
• When you use this mode with certain DVD and CD
players, performing operations such as skip or stop
may momentarily interrupt the output.
PURE DIRECT
The Pure Direct mode further reduces sources of
noise in addition to effect of the Source Direct mode,
by blocking output from the video jacks (VIDEO,
S-VIDEO, COMPONENT VIDEO and HDMI) and
turning the FL display off.
DTS-ES (Discrete 6.1, Matrix 6.1)
DTS-ES adds the surround back channel audio to
the DTS 5.1-channel format to improve the acoustic
positioning and makes acoustic image movement
more natural with the 6.1-channel reproduction.
This unit incorporates a DTS-ES decoder, which
can handle DTS-ES Discrete-encoded and DTS-ES
Matrix-encoded program sources from DVD, etc..
DTS-ES Discrete 6.1 features digital discrete
recording of all channels including the surround back
channel(s) and higher quality of audio reproduction.
DTS-ES is not available in the system without a
surround back speaker.
ENGLISH
AUTO
Notes:
• Neo:6 mode is available to 2ch input signals which
are encoded in Dolby Digital or PCM Analog
format.
• PCM-audio signals can be subjected to Neo:6
processing when the sampling frequency is 32 kHz,
44.1 kHz or 48 kHz.
Notes:
• Pro Logic IIx mode will decode as Pro Logic II
mode when the SURROUND BACK SPEAKER
is set NONE in SPEAKER SETUP menu. (See
SPEAKER SETUP, page 27)
• Pro Logic IIx mode is available for a 2ch input signal
which is encoded in Dolby Digital or PCM format.
• PCM-audio signals can be subjected to Pro Logic
processing when the sampling frequency is 32 kHz,
44.1 kHz or 48 kHz.
37
SR4002-5002U DFU_01_E2_2.indd 37
07.7.9 2:47:37 PM
ENGLISH
CIRCLE SURROUND II
(CSII-CINEMA, CSII-MUSIC, CSII-MONO)
Circle Surround is designed to enable multichannel
surround sound playback of non-encoded and
multichannel encoded material.
Backward compatibility provides listeners with up to
6.1 channels of surround performance from entire
collection of music and film, including broadcast,
videotape and stereo recorded music.
Depending on source material, you can select CSIICinema mode, CSII-Music mode or CSII-Mono
mode.
CSII Cinema mode
This mode is suited for playing back Circle Surroundencoded and non-encoded film and television
soundtracks. Cinema Mode enables 6.1-channel
surround playback of 2-channel sources such as
Video Cassettes, TV broadcasts, streaming media
and DVDs.
CSII Music mode
This mode is suited for playing back Circle Surroundencoded and non-encoded music. Music Mode
decodes, music DVDs, radio and TV music broadcasts
and CDs into enveloping 6.1-channel surround.
CSII-Mono mode
This mode plays back monaural recordings from
any source, including CDs, DVDs and TV and radio
broadcasts in compelling 6.1-channel surround.
Notes:
• CS II mode is available for 2ch input signals which
are encoded in Dolby Digital or PCM format.
• PCM-audio signals can be subjected to CS II
processing when the sampling frequency is 32 kHz,
44.1 kHz or 48 kHz.
STEREO
CAUTION
This mode bypasses all surround processing.
In stereo program sources, the left and right channels
play normally when PCM-audio or analog stereo is
input.
With Dolby Digital and DTS sources, the 5.1
multichannels are converted to two channel stereo.
96 kHz PCM source material can be played back in
stereo mode.
NOTE for DTS signal
* Connected DVD player, laserdisc player or CD
player needs to support DTS digital output. You
may not be able to play some DTS source signals
from certain CD players and LD players even if
you connect the player to this unit digitally. This
is because the digital signal has been processed
(such as the output level, sampling frequency
or frequency response), and this unit cannot
recognize the signal as DTS data.
* You can not listen to DTS-encoded software in a
multiroom.
* Depending on the player used, DTS play may
produce a short noise. This is not a malfunction.
* While signals from a DTS laserdisc or CD are
playing in another surround mode, you cannot
switch to digital input or from digital input to analog
input from the INPUT SETUP in the MAIN MENU
or by pressing the A/D button.
* The outputs for VCR 1 OUT, DSS/VCR 2 OUT,
TAPE OUT, and CD-R OUT output analog audio
signals only. Do not record from CDs or LDs that
support DTS using these outputs. If you do, the
DTS-encoded signal will be recorded as noise.
VIRTUAL
This mode creates a virtualized surround sound
experience from a two-speaker (front L and R)
playback system playing any multichannel audio
source (such as found on DVDs and digital
broadcasts), including Dolby Digital, Dolby Pro Logic
or DTS.
MULTI CH. ST
This mode is used to create a wider, deeper and more
natural soundstage from two channel source material.
This is done by feeding the left channel signal to
both left front and left surround speaker and the right
channel signal to both right front and right surround
speaker. Additionally, the center channel reproduces
a mix of the right and left channel.
NOTE for Dolby Digital Surround EX signal
* When playing Dolby Digital Surround EX-encoded
software in 6.1 channels, it is required to set the
EX/ES mode.
* Note that some of Dolby Digital Surround
EX-encoded software does not contain the
identification signal. In this case, set the EX/ES
mode manually.
NOTE for 96 kHz/192 kHz PCM audio
* The AUTO, Pure Direct, and Stereo modes can be
used when playing PCM signals with a sampling
frequency of 96/192 kHz (such as from DVDVideo/Audio discs).
* Certain DVD player models inhibit digital output.
For details, refer to the player’s operation manual.
* Some DVD discs feature copy protection. When
using such disc, 96 kHz PCM signal is not output
from the DVD player. For details, refer to the
player’s operation manual.
NOTE for HDCD signal
* HDCD is effective only through digital input.
* You may not be able to play some HDCD source
signals from certain CD players if you connect
the player to this unit digitally. This is because the
digital signal has been processed (such as the
output level, sampling frequency or frequency
response) and this unit cannot recognize the
signal as HDCD data.
38
SR4002-5002U DFU_01_E2_2.indd 38
07.7.9 2:47:38 PM
DISPLAY MODE
ER SR5002
LEARN
SOURCE
SEND
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
l/
SLEEP
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
AUTO
ENTER
AUTO
HT-EQ
MENU
EXIT
BAND
T-MODE
1
dts
2
3
EX/ES
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
CS
LIP SYNC/
INPUT
T.MODE
In normal operation, the audio or video source
selected for listening through this unit is sent to the
record outputs.
This means that any program you are watching
or listening to may be recorded simply by placing
machines connected to the outputs for TAPE OUT,
CD/CDR OUT, VCR OUT in the record mode.
Recording the video from one source and
the audio from another
You can add the sound from one source to the
video of another source to make your own video
recordings.
Below is an example of recording the sound from
a compact disc player connected to CD IN and the
video from a video camera connected to DSS to
video cassette recorder connected to the VCR OUT
jack.
To record the input source signal you are currently
watching or listening to
1.
2.
P.SCAN
You can select the display mode for the front display
of the unit.
To select this mode, press the DISPLAY on the
remote controller.
When this button is pressed, the display mode is
switched in the following sequence.
→ Surround Mode → Auto-display Off → Display Off
→ Input Function → Surround Mode....
In Auto display off mode, the display is off. But, if you
make a change to the unit such as input or surround
mode, the display will show that change, then go
back to off after about 3 seconds. When changing the
volume, it is not displayed.
In Display off mode, the display is off completely.
Note:
Only the DISP indicator will be illuminated on the
front display in display off condition
1.
-
PRESET
+
-
TUNING
+
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
BASS
TV
AUDIO
SELECTING ANALOG AUDIO INPUT OR
DIGITAL AUDIO INPUT
TV
DVD
VCR
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
4
5
6
M-CH ST
STEREO
NIGHT
7
VCR
DSS
CL
CH/ CAT
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
AV SURROUND RECEIVER SR5002
DSS
REMOTE CONTROLLER
TREBLE
DVD
ENGLISH
RECORDING AN ANALOG SOURCE
OTHER FUNCTION
P.SCAN
8
9
7.1CH IN
A/D
HT-EQ
0
+10
MEMO
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
VOLUME
INPUT SELECTOR
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
DVD
VCR
BASS
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
1.
TV
REMOTE CONTROLLER
AUDIO
TREBLE
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
1.
Switch the video output source to VCR by
simply pressing the input selector buttons on
the remote controller.
2.
Switch the audio input source to CD by simply
pressing the input selector buttons on the
remote controller.
3.
Now “CD” has been selected as the audio input
source and “VCR” as the video input source.
STANDBY
POWER ON/STANDBY
SETUP MIC
MENU
PHONES
REMOTE CONTROLLER
1.
Select the input source to record by turning the
INPUT SOURCE knob on the front panel or
simply press the input selector buttons on the
remote controller.
The input source is now selected and you may
watch or listen to it as desired.
2.
The currently selected input source signal is
output to the TAPE OUT, CD/CDR OUT, VCR
OUT outputs for recording.
3.
Start recording to the recording component as
desired.
Notes:
• If you change the input source during recording, you
will record the signals from the newly selected input
source.
• You cannot record the surround effects.
• Digital input signals are only output to the digital
outputs. There is no conversion from digital to
analog.
When connecting CD players and other digital
components, do not connect only the digital
terminals, but the analog ones as well.
If you have already assigned the digital inputs, you
can temporarily select the audio input mode for each
input source as following procedures.
Press the AMP button and press the A/D (0) button.
When this button is pressed, the input mode is
switched in the following sequence.
→ HDMI Auto → HDMI → Digital → Analog → HDMI
Auto....
In HDMI Auto mode, the types of signals being input
to the digital and analog input jacks for the selected
input source are detected automatically.
If no digital signal is being input, the analog input
jacks are selected automatically.
In Digital and HDMI mode, input is fixed to an
assigned digital input terminal.
In analog mode, the analog input jacks are selected.
This selecting is temporary, so the result will not be
stored in memory.
If you need to change the input mode completely, use
INPUT SETUP in OSD menu system. (see page 27)
39
SR4002-5002U DFU_01_E2_2.indd 39
07.7.9 2:47:38 PM
ENGLISH
LISTENING THROUGH HEADPHONES
DOLBY HEADPHONE MODE
This jack may be used to listen to the unit’s output
through a pair of headphones. Be certain that the
headphones have a standard 1/4” stereo phono
plug.
Note that the speakers will automatically be turned
off when the headphone jack is in use.
ATTENUATION TO ANALOG INPUT SIGNAL
This feature simulates the waveforms of the actual
sounds heard from the speakers.
When headphones are used, the MENU button
automatically switches to the Dolby headphone
mode.
The OSD that appears when the MENU button is
pressed is shown below.
REC
-
T.DISP
PRESET
+
PTY
-
F.DIRECT
TUNING
+
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
TV
DVD
VCR
DSS
TUNER
CD
CDR
MD
BASS
AUDIO
TREBLE
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
HEAD PHONE
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DOLBY HP MODE : ON
SURROUND
: OFF
STANDBY
POWER ON/STANDBY
SETUP MIC
MENU
PHONES
Notes:
• When using headphones, the surround mode will
change to BYPASS and Dolby Headphone by
MENU and Cursor button.
• The surround mode returns to the previous setting
as soon as the headphone plug is removed from the
jack.
• The tone control function can not work through the
headphones output.
L LEVEL
R LEVEL
:
:
0 dB
0 dB
DOLDBY HP (Headphone) MODE can be selected
with the left and right cursor buttons.
BYPASS → ON → BYPASS
BYPASS: Bypasses the Dolby headphone mode
and delivers ordinary 2-channel stereo.
ON: Dolby headphone mode active.
When the PURE DIRECT and SOURCE DIRECT
mode is selected, Dolby surround processing is
bypassed and “✽✽✽” is displayed as the mode
indication.
If the selected analog audio input signal is greater
than the capable level of internal processing, the
“PEAK” indicator will light up on the front display. If
this happens, you should press the ATT button on
the remote controller.
“ATT” indicator will be illuminated when this function
is activated. The signal-input level is reduced by
about half. Attenuation will not work with the output
signal of TAPE-OUT, CD/CDR-OUT and VCR-OUT.
This function is memorized for each individual input
source.
Notes:
• The surround mode returns to the previous setting as
soon as the plug is removed from the jack.
• The Dolby Headphone function will not work when
32 or 96 kHz PCM digital signals are input.
This unit is equipped for future expansion through the
use of Multi channel Super Audio CD multichannel
player or DVD-Audio player.
When this is selected, the input signals connected to
the L(front left), R (front right), CENTER, SL (surround
left), SR (surround right) and SBL (surround back left)
and SBR (surround back right) channels of the 7.1
CH. In jacks are output directly to the front (left and
right), center, surround (left and right) and surround
back speaker systems as well as the pre-out jacks
without passing through the surround circuitry.
In addition, the signal input to the SW (subwoofer)
jack is output to the PRE OUT SW (subwoofer) jack.
When 7.1 CH. INPUT is selected, the last video input
used remains routed to the Monitor Outputs.
This permits simultaneous viewing with video
sources.
SPEAKER A/B
M-CH ST
STEREO
NIGHT
7
8
9
CL
CH/ CAT
The surround mode can be selected when mode is
ON.
L/R LEVEL can be set in the ±10 dB range.
7.1 CH INPUT
INFO
7.1CH IN
A/D
0
+10
P.SCAN
HT-EQ
MEMO
VOLUME
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
MENU
This unit has speaker system - A and speaker
system- B for front L/R channels.
You can select these systems by pressing
SPEAKERS A/B button on the front panel or SPKAB on the remote controller.
40
SR4002-5002U DFU_01_E2_2.indd 40
07.7.9 2:47:39 PM
M-CH ST
AV SURROUND RECEIVER SR5002
MULTI
SPEAKER
MULTI
STEREO
7
INPUT SELECTOR
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
2.
4.
9
A/D
P.SCAN
HT-EQ
0
+10
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
CL
CH/ CAT
NIGHT
8
7.1CH IN
MEMO
VOLUME
STANDBY
POWER ON/STANDBY
SETUP MIC
INFO
PHONES
MENU
TV AUTO ON/OFF FUNCTION
If you don’t need to connect 7.1 Ch. input terminals
with multi channel decoder,
L(front left) and R (front right) inputs terminals are
available as AUX2 input.
In this case, You can connect additional audio source
to AUX2 as other audio input terminals.
4.
T.DISP
PTY
2.
F.DIRECT
+
-
TUNING
MULTI
SPEAKER
UP
1.
CLEAR
MUTE
BAND
T-MODE
DIGITAL
ATT
AUX 1 INPUT
S-VIDEO
VIDEO
PURE
DIRECT
AUTO
HT-EQ
SIMP
SETU
STANDBY
POWER ON/STANDBY
MEMORY
SURROUND
MODE
+
VOLUME
DOWN
L
AUDIO
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
BASS
SETUP MIC
MEN
DVD
VCR
DSS
CD
CDR
MD
AUX1
AUX2
AMP
R
TAPE
3.
Turn OFF the power to the TV TUNER and the
unit.
4.
Turn ON the TV TUNER and tune in a receivable
station.
TREBLE
TV
REMOTE CONTROLLER
Connect your TV TUNER (etc) to the TVVIDEO in terminal. Be sure to connect the
VIDEO input.
PHONES
AUDIO
TUNER
TV
DVD
VCR
TUNER
CD
CDR
DSS
MD
TAPE
AUX1
AUX2
AMP
R5002
MULTI
PRESET
When no video signal is connected to the unit or
a DVD, etc., is connected directly to your TV, the
unnecessary video circuit can be turned off by
selecting the “VIDEO OFF” setting.
To select video off, press the AMP button and press
the V-OFF button.
Be sure the TV auto mode is ENABLED. (Refer
page 28 : System Setup)
EXIT
REC
-
AUTO POWER ON
1.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
ENTER
T.TONE
/SET UP
This function allows the component connected to the
TV-VIDEO in jack to control the power (ON/OFF) to
the unit.
VIDEO ON/OFF
ENGLISH
AUX2 INPUT
2. 1.
5.
HT-EQ (HOME THEATER EQUALIZER)
REMOTE CONTROLLER
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
REC
ENTER
MENU
-
T.DISP
PRESET
DISC+
+
PTY
-
TUNING
ANGLE
SUB TITLE
V-OFF
ATT.
DVD
VCR
CH-SEL
BASS
When the station is received, this unit turns ON
and TV is selected automatically.
TV
F.DIRECT
+
AUDIO
TREBLE
DSS
AV SURROUND RECEIVER SR5002
1.
INPUT SELECTOR
Select a desired Video source to decide the
routed video signal to the Monitor Outputs.
VOLUME
AUTO POWER OFF
LIP.SYNC (SR5002 only)
DOWN
2.
3.
Press the 7.1 CH INPUT button on the front
panel or press 7.1 CH IN on the remote
controller to switch the 7.1 channel input.
If it is necessary to adjust the output level of
each channel, press the CH.SEL button on the
remote controller.
Adjust the speaker output levels so that you can
hear the same sound level from each speaker
at the listening position. For the front left, front
right, center, surround left, surround right and
surround back speakers, the output levels can
be adjusted between –10 to +10 dB.
The subwoofer can be adjusted between –15
and +10 dB.
These adjustments result will be stored to 7.1
CH. INPUT memory.
4.
Adjust the main volume with the MAIN VOLUME
knob or the VOLUME buttons on the remote
controller.
To cancel the 7.1 CH. INPUT setting, press the 7.1
CH INPUT button on the front panel or press 7.1 CH
IN on the remote controller.
Notes:
• 7.1 CH. Input mode bypasses the internal surround
processing, so SURROUND mode cannot be
selected.
• In addition, there is no signal at the record outputs
when the 7.1 CH. Input is in use.
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
MEMORY
CLEAR
SETUP MIC
HT-EQ
MENU
EXIT
BAND
T-MODE
PHONES
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
In the above situation, turn the TV TUNER OFF
or select a channel that does not contain any
broadcast.
2.
The power to the unit switches to STANDBY
after approx. 5 minutes.
L
At cinemas, the front left, front right and center
speakers are located behind the screen. So, screen
damping is taken into account when mastering movie
software, with an emphasis on high frequencies.
When playing back such software at home, the
signal takes on different characteristics from those
at the cinema. This unit includes HT-EQ to rectify
the sound difference between that experienced at a
cinema and in a home theater, allowing you to enjoy
the same sound you would experience at the cinema
at home. The HT-EQ feature is available except in the
following modes.
• 7.1 CH INPUT
• PURE-DIRECT
• SOURCE DIRECT
• When VIRTUAL is set for the surround mode
1.
1.
ENTER
AUTO
POWER ON/STANDBY
DISPLAY
MUTE
STANDBY
Notes:
• AUTO POWER OFF is canceled if this unit is set to
a source other than TV.
The function reactivates when TV is selected again.
• Some TV broadcasts may cause the TV AUTO
FUNCTION to turn ON.
• The S-Video terminal does not support “TV AUTO
ON/OFF” function.
Depending on the image device (TV, monitor,
projector, etc.) connected to the SR5002, a time lag
can occur between image signal processing and
audio signal processing. Though minor, this time
lag can interfere with movie and music enjoyment.
The LIP.SYNC feature delays the audio signal with
respect to the image signal output from the SR5002
to correct the time lag between the sound and image.
It can be operated with the “LIP.SYNC” and 1 and
2 cursor buttons of the remote controller. Set the
remote controller to the AMP mode before operating
the LIP.SYNC feature. The initial setting is OFF (0
ms).The time lag can be adjusted in 10 ms steps up
to 200 ms.
Watch the picture on the image device (i.e., TV,
monitor, projector, etc.) as you adjust the time lag.
Note:
The LIP.SYNC feature turns OFF (0 ms) in the
SOURCE DIRECT mode. When the SOURCE
DIRECT mode is deactivated, the set value of the LIP.
SYNC feature is automatically restored.
Press the HT-EQ button on the unit.
“EQ” indicator on the front panel will illuminate,
indicating the HOME THEATER EQUALIZER
has been activated.
2.
To cancel this function, press the HT-EQ button
again.
“EQ” indicator on the front panel will be
turned off, indicating the HOME THEATER
EQUALIZER has been deactivated.
41
SR4002-5002U DFU_01_E2_2.indd 41
07.7.9 2:47:39 PM
ENGLISH
(FM) TUNING MODE (AUTO STEREO OR MONO)
MANUAL TUNING
BASIC OPERATION
SLEEP
2.
(TUNER)
1.
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
SOURCE
1.
LISTENING TO THE TUNER
1
2
3
BAND
EX/ES
VIRTUAL
T.MODE
SLEEP
DOWN
4
5
6
STEREO
NIGHT
7
8
9
UP
1
CS
DISPLAY
CLEAR
MEMORY
MUTE
EXIT
BAND
T-MODE
DIGITAL
REC
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
MEMORY
ATT
T.DISP
PTY
BAND
T-MODE
DIGITAL
2.
-
PRESET
DISC+
+
-
TUNING
ANGLE
SUB TITLE
V-OFF
ATT.
CH-SEL
AUDIO
TREBLE
(Using the unit)
1.
To select tuner and desired band (FM or AM),
press the BAND button on the front panel.
AUTO TUNING
2.
Press the 3 or 4 cursor buttons on the front
panel to select the desired station.
2.
1.
AUTO
1.
1
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
2
3
BAND
EX/ES
VIRTUAL
T.MODE
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
REC
T.DISP
PTY
CS
P.SCAN
(Using the remote controller )
1.
DOWN
D
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
MEMORY
M
ENTER
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
2.
-
PRESET
+
-
TUNING
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
To select tuner and desired band (FM or
AM), press the BAND button on the remote
controller.
F.DIRECT
CLEAR
+
AUDIO
2.
6
NIGHT
7
R
+
Note:
Preset memory for the tuner will clear by changing
this setup.
DISPLAY
L
5
STEREO
CH/ CAT
EXIT
3
VIRTUAL
4
CL
BASS
SLEEP
AUX 1 INPUT
S-VIDEO
VIDEO
ENTER
MENU
Press the 5 or 6 on the remote controller to
tune in the desired station.
T.MODE
8
9
7.1CH IN
A/D
0
+10
SPKR A/B
MUTE
HT-EQ
MEMO
VOLUME
When in the auto stereo mode, AUTO indicator will
be illuminated on the display.
The “ST” indicator is illuminated when a stereo
broadcast is tuned in.
At open frequencies, the noise is muted and the
“TUNED” and “ST” indicators are not illuminated.
If the signal is weak, it may be difficult to tune into
the station in stereo. In such a case, press the
T-MODE button on the front panel or remote
controller.
“AUTO” indicator is not illuminated, if FM stereo
broadcasts are received in monaural and the “ST”
indicator is not illuminated.
To return to auto stereo mode, press the T-MODE
button or press T-MODE button on the remote
controller again. AUTO indicator is illuminated on the
display.
If no button is pressed during this period, the
current station is memorized in location Preset
02.
If you wish to skip the current station, press the
3 cursor button during this period, this station
is skipped and auto presetting continues.
5.
Operation stops automatically when all 50
preset memory positions are filled or when
auto scanning attains the highest end of all
bands. If you desire to stop the auto preset
memory at anytime, press the CLEAR button.
Note:
It is possible that existing preset memory positions
will be overwritten.
PRESET MEMORY
SET
OFF
To select tuner and desired band (FM or AM),
press the BAND button on the front panel.
Press the 3 or 4 cursor buttons on the front
panel for more than 1 second to start the auto
tuning function.
SLEEP
1
3.
To select tuner and desired band (FM or
AM), press the BAND button on the remote
controller.
2.
Press the 5 or 6 for more than 1 second on
the remote controller.
3.
Automatic searching begins then stops when a
station is tuned in.
If tuning does not stop at the desired station, use to
the “Manual tuning” operation.
DISPLAY
P.DIRECT
dts
2
3
EX/ES
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
SURROUND
dts
LIP SYNC/
INPUT
3.
2. 4.
SLEEP
SURROUND
LIP SYNC/
INPUT
1.
1
CS
2
3
BAND
EX/ES
VIRTUAL
T.MODE
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
7.1CH IN
A/D
P.SCAN
T.MODE
With this unit you can preset up to 50 FM/AM stations
in any order.
For each station, you can memorize the frequency
and reception mode if desired.
7.1CH IN
A/D
0
+10
SPKR A/B
MUTE
1
CEIVER SR5002
3.
HT-EQ
P.SCAN
SURROUND
MODE
MULTI/ CAT
M-SPKR
/SET UP
HT-EQ
EXIT
PURE
DIRECT
2.
REC
-
T.DISP
PRESET
+
PTY
AUTO
DISPLAY
-
TUNING
+
To select tuner and desired band (FM or
AM), press the BAND button on the remote
controller.
2.
Press the F.DIRECT on the remote controller,
display will show “FREQ - - - -”.
This function automatically scans the FM and AM
band and enters all stations with proper signal
strength into the memory.
2. 4. 2. 5. 1. 3.
EXIT
T
2.
2
3
EX/ES
VIRTUAL
4
5
6
STEREO
NIGHT
7
8
9
7.1CH IN
A/D
MEMORY
BAND
dts
M-CH ST
CH/ CAT
INFO
0
+10
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
SURROUND
LIP SYNC/
INPUT
T.MODE
P.SCAN
HT-EQ
MEMO
VOLUME
1.
Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
2.
Press the MEMORY button on the front panel.
“– –“ (preset number) starts blinking on the
display.
Input your desired station’s frequency with the
numeric buttons on the remote controller.
3.
Select the preset number by pressing the 1
or 2 cursor buttons, while this is still blinking
(approx. 5 seconds)
4.
Press the MEMORY button again to enter. The
display stops blinking.
The station is now stored in the specified preset
memory location.
VOLUME
DOWN
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
UP
MUTE
STANDBY
POWER ON/STANDBY
ATT
ENTER
SETUP MIC
PHONES
MENU
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
The desired station will automatically be tuned.
1.
To select FM, press the BAND button on the
front panel.
MENU
(Using the unit)
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
4.
MENU
P.DIRECT
F.DIRECT
1.
3.
HT-EQ
CS
CL
SIMPLE
SETUP
AUTO PRESET MEMORY
MEMO
VOLUME
DISPLAY
AUTO
ENTER
CL
CH/ CAT
Automatic searching begins then stops when a
station is tuned in.
(Using the remote controller)
P.DIRECT
AUTO
AUTO
CS
DISPLAY
ON
l/
1.
4.
MANUAL PRESET MEMORY
SLEEP
SOURCE
3.
The band can be changed by the BAND button.
AUDIO
(Using the unit)
2.
Each time the tuner finds a station, scanning
will pause and the station will be played for five
seconds.
During this time, the following operations are
possible.
P.SCAN
DIRECT FREQUENCY CALL
1.
3.
LIP SYNC/
INPUT
dts
2
EX/ES
M-CH ST
F.DIRECT
CLEAR
M
HT-EQ
ON
SURROUND
P.SCAN
ENTER
D
OFF
P.DIRECT
AUTO
CS
M-CH ST
DOWN
Frequency scan step for AM is selectable.
Default setup is 10 kHz step, if your country’s
standard is 9 kHz step, press BAND button on the
remote controller more than 6 seconds. Scan step
will change.
SET
DISPLAY
While pressing the MEMO button, press the 2
cursor button.
“AUTO PRESET” will appear on the display,
and scanning starts from the lowest frequency.
l/
VOLUME
AUTO
2.
42
SR4002-5002U DFU_01_E2_2.indd 42
07.7.9 2:47:39 PM
(Using the remote controller)
1.
1.
2.
3.
Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
Press the MEMO button on the remote
controller. “– –“ (preset number) starts blinking
on the display.
Enter the desired preset number by pressing
the numeric buttons.
Note:
When entering a single digit number (2 for example),
either input “02” or just input “2” and wait for a few
seconds.
Preset stations are recalled in sequence (No.1
→ No.2 → etc.) for 5 seconds each.
3.
You can fast forward the preset stations by
pressing the T continuously.
SLEEP
DISPLAY
AUTO
1
1.
CS
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
SURROUND
dts
LIP SYNC/
INPUT
2
3
EX/ES
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
7.1CH IN
A/D
0
+10
SPKR A/B
MUTE
CL
SURROUND
MODE
P.DIRECT
CH/ CAT
T.MODE
HT-EQ
MENU
When the desired preset station is received,
cancel the preset scan operation by pressing
the CLEAR button or P.SCAN on the remote
controller.
CLEARING STORED PRESET STATIONS
You can remove preset stations from the memory
using the following procedure.
P.SCAN
2. 3.
HT-EQ
MEMO
AUTO
1
CS
VOLUME
VOLUME
EXIT
BAND
T-MODE
REC
1.
-
T.DISP
PRESET
+
PTY
-
F.DIRECT
TUNING
2.
6
STEREO
NIGHT
7
+
AUDIO
DISPLAY
MEMORY
CLEAR
MUTE
ENTER
EXIT
(Using the unit)
BAND
T-MODE
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
3.
INFO
1.
Press the S or T buttons to select the
desired preset station, or input your desired
preset channel with the numeric buttons on
the remote controller.
CS
EX/ES
5
6
STEREO
NIGHT
7
3.
VIRTUAL
4
M-CH ST
LIP SYNC/
INPUT
CL
CH/ CAT
REC
-
8
9
7.1CH IN
A/D
0
+10
SPKR A/B
MUTE
T.DISP
PTY
HT-EQ
MEMO
1.
3.
VOLUME
PRESET
+
-
F.DIRECT
TUNING
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
+
AUDIO
3.
DISPLAY
MEMORY
UP
2.
Press the MEMORY button on the front panel
or press the MEMO button on the remote
controller for more than 3 seconds.
3.
The left most column of the station name
indicator flashes, indicating the character entry
ready status.
4.
When you press the 3 or 4 cursor buttons
on the front panel or the 5 / 6 buttons on
the remote controller, alphabetic and numeric
characters will be displayed in the following
order:
CLEAR
MUTE
ATT
ENTER
AUTO
SETUP MIC
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
PHONES
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
P.SCAN
8
9
7.1CH IN
A/D
HT-EQ
0
+10
MEMO
VOLUME
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
If you have stations memorized, and there is a gap in
the sequential order:
I.e. the stations are stored as follows
1) 87.1 MHz
2) 93.1 MHz
3) 94.7 MHz
10) 105.9 MHz
(notice there is no stations programmed for pre sets
for 4-9), you can have pre set 10 become pre set 5:
To sort the numbers, press the 4 cursor button while
pressing the MEMORY button.
“PRESET SORT” will appear on the display and
sorting will be done.
UP →
← DOWN
5.
NAME INPUT OF THE PRESET STATION.
2.
Press the MEMORY button on the front panel
or press the MEMO button on the remote
controller.
The stored preset number blinks in the display
for 5 seconds. While blinking, press the
CLEAR button on the front panel or the remote
controller.
5. 2. 5. 6.
To move back and forth between the characters,
press the 1 / 2 cursor buttons or press S or
T buttons on the remote controller.
Note:
Unused columns should be filled by entering blanks.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
VOLUME
DOWN
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
MEMORY
CLEAR
EXIT
BAND
T-MODE
UP
MUTE
STANDBY
POWER ON/STANDBY
DISPLAY
After selecting the first character to be entered,
press the MEMORY or ENTER buttons, press
the MEMO button on the remote controller.
The entry in this column is fixed and the next
column starts to flash. Fill the next column the
same way.
This function allows the name of each preset channel
to be entered using alphanumeric characters.
Before name inputting, you need to store preset
stations with the preset memory operation.
MENU
Recall the preset number to be cleared with
the method described in “Recalling” a preset
station.
4.
A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → +
→ / → (Blank) → A
T.MODE
1.
T.MODE
P.SCAN
SIMPLE
SETUP
4.
3.
PRESET SCAN
PURE
DIRECT
STANDBY
POWER ON/STANDBY
Select the desired preset station by pressing
the 1 or 2 cursor buttons on the front panel
(Using the remote controller)
1.
3
VIRTUAL
M-CH ST
CH/ CAT
SUB TITLE
2
EX/ES
5
CL
ANGLE
dts
4
DOWN
DISC+
DOWN
SURROUND
MODE
No stored preset number will be skipped.
ENTER
AUTO
Recall the preset number to be inputted name
with the method described in “Recalling” a
preset station.
VOLUME
MULTI
SPEAKER
MULTI
2.
1.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
“PRESET SCAN” appears on the display and
then the preset station with the lowest preset
number is recalled first.
RECALLING A PRESET STATION
1.
SORTING PRESET STATIONS
Press the P.SCAN on the remote controller.
ENGLISH
(Using the remote controller)
ATT
6.
To save the name, press the MEMORY button
on the front panel or remote controller for more
than 2 seconds.
ENTER
SETUP MIC
MENU
DIGITAL
PHONES
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
Ten keypad
1
7
2. 5. 6.
“xx CLEAR” appears on the display to indicate
that the specified preset number has been
cleared.
2
D→E→F→2→D
3
G→H→I→3→G
MUTE
4
J→K→L→4→J
M-SPKR
5
M→N→O→5→M
6
P→Q→R→6→P
7
S→T→U→7→S
8
CH/ CAT
9
7.1CH IN
A/D
HT-EQ
0
+10
MEMO
SPKR A/B
MULTI/ CAT
CL
VOLUME
INFO
MENU
ENTER
Note:
To clear all stored preset stations, press and hold the
CLEAR and the ENTER buttons for two seconds.
T.TONE
/SET UP
EXIT
REC
5.
4.
-
T.DISP
PRESET
DISC+
+
PTY
-
F.DIRECT
TUNING
ANGLE
SUB TITLE
V-OFF
ATT.
DVD
VCR
CH-SEL
BASS
TV
Press, press again, press again, etc.
A→B→C→1→A
+
8
V→W→X→8→V
9
Y → Z → space → 9 → Y
0
–→+→/→0
AUDIO
TREBLE
DSS
43
SR4002-5002U DFU_01_E2_2.indd 43
07.7.9 2:47:40 PM
ENGLISH
CHECKING THE XM SIGNAL STRENGTH
AND RADIO ID
LISTENING TO XM SATELLITE RADIO
(SR5002 ONLY)
3.
ENTER
SELECTING AN INPUT SOURCE
T.TONE
/SET UP
Before you can listen to XM Satellite Radio, you must
first select the input source on the SR5002.
SOURCE
1.
SET
OFF
Select channel 0 (XM000) with the 3 or 4
cursor buttons of the SR5002 or the Q or
R buttons of the remote controller.
EXIT
REC
T.DISP
PTY
3.
F.DIRECT
PRESET
+
-
TUNING
+
1.
T.TONE
/SET UP
INPUT SELECTOR
T.TONE
/SET UP
REC
ANGLE
SUB TITLE
DISPLAY
1
INPUT SELECTOR
CS
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
M-CH ST
3
EX/ES
VIRTUAL
T.MODE
5
6
STEREO
NIGHT
7
SURROUND
MODE
MULTI
SPEAKER
MULTI
BASS
V-OFF
9
A/D
HT-EQ
CL
0
+10
MEMO
DISC+
ANGLE
SUB TITLE
AUDIO
CH-SEL
V-OFF
ATT.
PRESET
PTY
EXIT
F.DIRECT
2.
DISC+
TREBLE
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
STANDBY
POWER ON/STANDBY
1.
+
-
TUNING
ANGLE
SUB TITLE
V-OFF
ATT.
REC
+
ATT.
AUDIO
DISPLAY
CH-SEL
P.SCAN
8
7.1CH IN
PURE
DIRECT
CH-SEL
MULTI
2
BAND
4
T.DISP
AUDIO
-
AUTO
ENTER
EXIT
AV SURROUND RECEIVER SR5002
ON
DISC+
SLEEP
You can display XM information (such as artist name/
song title, category or signal status) for the channel
currently selected in the front panel display.
ENTER
-
l/
AV SURROUND RECEIVER SR5002
MENU
INFO
SWITCHING XM INFORMATION IN THE FRONT
PANEL DISPLAY
3.
-
T.DISP
PRESET
+
PTY
-
F.DIRECT
TUNING
+
1.
ENTER
SETUP MIC
MENU
BASS
EXIT
PHONES
Press the T.DISP button 3 times to displayed
Signal Status.
TREBLE
DISC+
TV
DVD
VCR
ANGLE
SUB TITLE
V-OFF
ATT.
AUDIO
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
CH-SEL
BASS
TREBLE
REMOTE CONTROLLER
STANDBY
AUTO
POWER ON/STANDBY
SETUP MIC
HT-EQ
PHONES
BASS
S I G N A L :
1.
• The Radio ID is displayed.
TREBLE
TV
DVD
VCR
TUNER
CD
CDR
DSS
MD
TAPE
AUX1
AUX2
AMP
1.
• The display changes as shown below according to
the receiving condition.
X M O O O R A D I O
I D
SIGNAL: ■■■■■■
SIGNAL: STRONG
(Signal strength is good)
2.
SIGNAL: ■■■■
SIGNAL: MARGINAL
(Signal strength is Marginal)
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
VOLUME
DOWN
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
MEMORY
UP
SIGNAL: ■■
SIGNAL: WEAK
(Signal strength is poor)
CLEAR
MUTE
STANDBY
ATT
ENTER
AUTO
POWER ON/STANDBY
SETUP MIC
HT-EQ
MENU
EXIT
PHONES
BAND
Channel number/name
Artist name/Song title
REMOTE CONTROLLER
RC5001SR
MULTI
Press the T.DISP button to displayed
INFORMATION.
T-MODE
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
XM NO SIGNAL
SIGNAL: NON
(Loss of the signal)
(Using the SR5002)
1.
Turn the INPUT SELECTOR knob to select
“TUNER”.
2.
Press the BAND button to select XM band.
(Using the remote controller)
1.
To select tuner, Press the TUNER button twice
within two seconds on the remote controller.
2.
Press the BAND button to select XM band.
2.
Adjust the antenna location until signal strength
is good.
Channel category
Notes:
• If “ANTENNA” appears in the front panel display,
the XM Mini-Tuner and Home Dock may not be
connected to the XM terminal on the rear panel of
this unit properly.
• The ATT function is also effective when XM is
selected.
Signal Status
When the Channel number/name is displayed:
X M O 4 0 : D e e p T r c
4 0 : D e e p T r a c k s
(If text is more than 13 characters long, the text is
scrolled.)
Note:
The front Panel display can indicate up to 13 alphanumeric
characters at once. If the information contains more then
13 characters, the information scrolls from right to left.
44
SR4002-5002U DFU_01_E2_2.indd 44
07.7.9 2:47:41 PM
2.
When you press the INFO button, the following
information will be displayed.
N A M E / T I T L E
VIDEO
AUDIO
P i n k
F l o i d
F l o i d
/
/
This XM information can also be displayed on a TV
monitor connected to the SR5002.
VOLUME
M-SPKR
MENU
2.
ENTER
T.TONE
/SET UP
EXIT
REC
T.DISP
PTY
F.DIRECT
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
BASS
AUDIO
3.
2.
DVD
VCR
DSS
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
VOLUME
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
Press the AMP button on the remote
controller.
DISPLAY
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
PHONES
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
VOLUME
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
STANDBY
UP
SEND
CLEAR
ATT
ENTER
AUTO
POWER ON/STANDBY
MEMORY
MUTE
SETUP MIC
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
PHONES
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
SOURCE
R
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
l/
SLEEP
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
:040
:DeepTracks
:Pink Floid
:Money
:Rock
SLEEP
AUTO
1
CS
4
2
3
BAND
EX/ES
VIRTUAL
T.MODE
5
6
M-CH ST
STEREO
NIGHT
7
8
9
REC
T.DISP
PTY
2.
2
3
BAND
EX/ES
VIRTUAL
T.MODE
4
5
6
REC
T.DISP
PTY
-
P.SCAN
PRESET
+
-
EXIT
-
Press the INFO button again. The information
display will go out.
PRESET
DISC+
+
ANGLE
CH-SEL
V-OFF
-
TUNING
SUB TITLE
TUNING
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
Note:
If the information contains a character that cannot be
recognized by that unit, the character will be displayed
with “ ”(space).
3.
3.
TREBLE
TV
DVD
VCR
TUNER
CD
CDR
DSS
MD
TAPE
AUX1
AUX2
AMP
1.
REMOTE CONTROLLER
RC5001SR
ATT.
BASS
+
AUDIO
+
AUDIO
2.
F.DIRECT
DISC+
BASS
F.DIRECT
LIP SYNC/
INPUT
dts
1
CS
SOURCE
4.
ATT
ENTER
SETUP MIC
AUTO
RETURN
UP
CLEAR
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
XM INFORMATION
XM
CHAN
NAME
TITLE
CAT
MEMORY
MUTE
AUTO
TREBLE
TV
DVD
VCR
TUNER
CD
CDR
DSS
MD
TAPE
AUX1
AUX2
AMP
1.
REMOTE CONTROLLER
RC5001SR
(Using the SR5002)
(Using the SR5002)
1.
Turn the INPUT SELECTOR knob to select
“TUNER”.
2.
3.
Press the BAND button to select XM band.
Press the 1 or 2 cursor button on the front
panel to select the desired preset station.
1.
Turn the INPUT SELECTOR knob to select
“TUNER”.
2.
3.
Press the BAND button to select XM band.
(Using the remote controller)
Press the 3 or 4 cursor button on the front
panel to select the desired station.
1.
To select tuner, Press the TUNER button twice
within two seconds on the remote controller.
2.
3.
Press the BAND button to select XM band.
(Using the remote controller)
1.
SIMPLE
SETUP
STANDBY
POWER ON/STANDBY
TREBLE
TV
TUNER
REMOTE CONTROLLER
RC5001SR
1.
1.
When this display appears, press the INFO
button again. XM information like the following
will appear.
MAIN
MULTI/ CAT
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
SIGNAL:MARGINAL
Note:
To change the display content from XM information to
SR5002 functions, do so with the DISPLAY button.
2.
LEARN
3.
C A T : R o c k
INFO
3.
DOWN
DOWN
When the channel category is displayed:
MUTE
1.
MULTI
MAIN VOLUME
-------------------MAIN
RETURN
EXIT
Note:
The front Panel display can indicate up to 13
alphanumeric characters at once. If the information
contains more then 13 characters, the information
scrolls from right to left.
SPKR A/B
You can search for the channel you want to listen to
using one of three search modes. You can also enter
the number directly to select the desired channel.
ALL CHANNEL SEARCH MODE
SURR-MODE:AUTO
MULTIROOM:ON
MULTISPKR:OFF
M o n e y
The “NAME/TITLE” is displayed for 2 seconds,
followed by the artist’s name and song title.
(If artist’s name or song title is more than 13 characters
long, the text is scrolled.)
CH/ CAT
:DVD
:XM
PRESET SEARCH MODE
SEARCH MODE
ENGLISH
When the channel Ar tist name/Song title is
displayed:
1.
To select tuner, Press the TUNER button twice
within two seconds on the remote controller.
2.
3.
Press the BAND button to select XM band.
S or T button to tune in the desired
preset station.
Or enter the preset station number with the
numeric buttons.
Press and hold the 5 or 6 button.
45
SR4002-5002U DFU_01_E2_2.indd 45
07.7.9 2:47:42 PM
ENGLISH
CATEGORY SEARCH MODE
(Using the SR5002)
You can select the desired channel from the category
allocated to each channel.
Category being aired can be only selected.
1.
Turn the INPUT SELECTOR knob to select
“TUNER”.
2.
3.
4.
Press the BAND button to select XM band.
5.
After selecting the Category, Press the 3 or 4
cursor button to select the desired station of the
category.
6.
You can return to the normal mode by press the
ENTER button during Category Search Mode.
1.
5. 3. 6.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
VOLUME
DOWN
SURROUND
MODE
MULTI
SPEAKER
MULTI
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
CLEAR
MUTE
STANDBY
ATT
ENTER
AUTO
POWER ON/STANDBY
MEMORY
UP
SETUP MIC
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
PHONES
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
Press the ENTER button on the front panel.
Press the 1 or 2 button on the front panel to
select the desired Category.
7.
You can return to the normal mode by press
the MULTI/CAT button during Category Search
Mode.
Note:
Category search automatically ends 5 minutes after
the last operation.
CHANNEL DIRECT CALL
You can select the desired channel by directly tapping
the numeric keypads on the remote controller.
R
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
1
4.
2.
CS
(Using the remote controller)
1.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
VOLUME
DOWN
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
MUTE
STANDBY
POWER ON/STANDBY
UP
ATT
ENTER
SETUP MIC
MENU
DIGITAL
PHONES
AUTO
LIP SYNC/
INPUT
dts
1
CS
2
3
BAND
EX/ES
VIRTUAL
T.MODE
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
CH/ CAT
P.SCAN
7.1CH IN
A/D
HT-EQ
0
+10
MEMO
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
CL
2.
VOLUME
INFO
MENU
AUDIO
R
4.
5.
6.
T.DISP
PRESET
DISC+
+
PTY
-
ANGLE
SUB TITLE
V-OFF
ATT.
CH-SEL
BASS
TV
F.DIRECT
TUNING
+
AUDIO
6.
BAND
T.MODE
EX/ES
VIRTUAL
5
6
M-CH ST
STEREO
NIGHT
7
8
9
7.1CH IN
A/D
0
+10
CL
P.SCAN
HT-EQ
MEMO
2.
5.
The desired channel will automatically be
tuned.
Note:
If there is no input on the keypad for 5sec., the input is
cancelled to return to the original display
Notes:
• “LOADING” is displayed while receiving the
channel or information.
• “UPDATING” is displayed while updating encryption
code.
• When the selected channel is not available, “XM - -” is dispIayed.
• “OFF AIR” is displayed while air is suspended (e.g.
midnight).
VOLUME
SPKR A/B
MUTE
Press the BAND button to select XM band.
Press the TUNER button twice within two
seconds on the remote controller.
ENTER
T.TONE
/SET UP
Press the MULTI/CAT button.
EXIT
REC
Press the CAT 3 or CAT 4 button.
-
After selecting the category, Press the Q or
R button to select the desired station of the
category.
T.DISP
PRESET
DISC+
+
PTY
-
F.DIRECT
TUNING
+
ANGLE
SUB TITLE
V-OFF
ATT.
TV
DVD
VCR
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
CH-SEL
BASS
4.
AUDIO
TREBLE
DSS
1. 3.
REMOTE CONTROLLER
RC5001SR
1.
To select tuner, Press the TUNER button twice
within two seconds on the remote controller.
2.
3.
Press the BAND button to select XM band.
EXIT
REC
-
L
3
4
CH/ CAT
5.
4.
ENTER
T.TONE
/SET UP
AUX 1 INPUT
S-VIDEO
VIDEO
2.
3.
To select tuner, Press the TUNER button twice
within two seconds on the remote controller.
2
6.
4.
Press the TUNER button twice within two
seconds on the remote controller.
Press the F.DIRECT button.
TREBLE
DVD
VCR
“XM - - -” will appear on the display.
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
1. 3.
5.
Input the three digit number for your desired
Channel with the numeric keypad on the
remote controller.
46
SR4002-5002U DFU_01_E2_2.indd 46
07.7.9 2:47:42 PM
You can store the desired channel in the Preset
Memory.
In addition to AM and FM, it is possible to preset 50
XM channels.
3.
2.4.
SOURCE
SET
OFF
DISPLAY
P.DIRECT
AUTO
dts
1
CS
2
3
EX/ES
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
CL
ENTER
AUTO
HT-EQ
MENU
BAND
LIP SYNC/
INPUT
P.SCAN
A/D
HT-EQ
+10
MEMO
MUTE
M-SPKR
4
5
6
STEREO
NIGHT
8
9
7.1CH IN
A/D
4
5
6
M-CH ST
STEREO
NIGHT
7
2.
VIRTUAL
8
CH/ CAT
P.SCAN
9
7.1CH IN
A/D
HT-EQ
0
+10
MEMO
CL
D
3.
2.
You can remove preset stations from the memory
using the following procedure.
T.MODE
2. 5.
0
+10
MUTE
MUTE
M-SPKR
VOLUME
MULTI/ CAT
M-SPKR
MEMO
PRESET
+
ANGLE
-
TUNING
CH-SEL
SUB TITLE
V-OFF
ATT.
DVD
VCR
4.
4. 5.
ENTER
T.TONE
/SET UP
BASS
TV
3.
Select the preset number by pressing the 1
or 2 cursor buttons, While this is still blinking
(approx. 5 seconds)
0 1 X M 0 4 0
4.
VCR
Press the MEMORY button again to enter.
The display stops blinking.
The station is now stored in the specified preset
memory location.
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
(Using the remote controller)
1.
2.
Tune into the desired channel.
3.
Enter the desired preset number by pressing
the numeric buttons.
Press the MEMO button on the remote
controller. “- -” (preset number) starts blinking
on the display.
Note:
When entering a single digit number (2 for example),
either input “02” or just input “2” and wait for a few
seconds.
(Using the remote controller)
1.
To select tuner, Press the TUNER button twice
within two seconds on the remote controller.
2.
3.
Press the BAND button to select XM band.
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
4.
Press the INFO button. to view a list of tuner
preset channeI on the on screen display.
5.
If there are 10 or more preset channel, Press
the INFO button. again.
Press the TUNER button twice within two
seconds on the remote controller.
2.
3.
Press the P.SCAN.
4.
Pressing the T button during prescanning
speeds up scanning.
NO. 1
NO. 2
NO. 3
NO. 4
NO. 5
NO. 6
NO. 7
NO. 8
NO. 9
MAIN
PRESET LIST
XM010 XXXXXXXXXX
XM011 XXXXXXXXXX
XM015 XXXXXXXXXX
XM022 XXXXXXXXXX
XM125 XXXXXXXXXX
XM001 Preview
XM001 Preview
XM001 Preview
XM001 Preview
RETURN
EXIT
Preset stations are recalled in sequence (No.1
→ No.2 → etc.) for about 5-10 seconds each.
The time changes by the received condition. No
stored preset number will be skipped.
Also, pressing the S button returns to the
previous preset station.
5.
MEMORY
CLEAR
EXIT
BAND
T-MODE
+10
MUTE
MULTI/ CAT
M-SPKR
HT-EQ
MEMO
VOLUME
MUTE
2.
3.
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
MENU
1.
1.
Press the TUNER button twice within two
seconds on the remote controller.
DISPLAY
0
SPKR A/B
P.SCAN
DSS
1. 3.
REMOTE CONTROLLER
RC5001SR
XM
A/D
ENTER
ENU
1.
Recall the preset number to be cleared with
the method described in “PRESET SERCH
MODE”.
2.
Press the MEMORY button on the front panel
or Press the MEMO button on the remote
controller.
3.
The stored preset number blinks in the display
for 5 seconds. WhiIe blinking, Press the CLEAR
button on the front panel or CL button on the
remote controller.
4.
“xx CLEAR” appears on the dispIay to indicate
that the specified preset number has been
cleared.
DSS
Press the MEMORY button on the front panel.
- - X M 0 4 0
9
7.1CH IN
LIP SYNC/
INPUT
T.MODE
TREBLE
TREBLE
DVD
6
NIGHT
8
INFO
EXIT
BASS
”- -” (preset number) starts blinking on the
dispIay.
MPLE
ETUP
MENU
TV
5
STEREO
7
+
AUDIO
3
VIRTUAL
4
CH/ CAT
-
dts
2
EX/ES
M-CH ST
CL
DOWN
VOLUME
INFO
Tune into the desired channel.
1
CS
VOLUME
SPKR A/B
MULTI/ CAT
REMOTE CONTROLLER
RC5001SR
1.
2.
AUTO
P.SCAN
DISC+
(Using the SR5002)
2. 3.
HT-EQ
SPKR A/B
CL
EX/ES
T.MODE
0
SPKR A/B
BAND
T.MODE
M-CH ST
CH/ CAT
7.1CH IN
MULTI/ CAT
T-MODE
3
VIRTUAL
7
SURROUND
VOLUME
CH/ CAT
EXIT
2
EX/ES
CLEARING STORED PRESET STATIONS
CS
LIP SYNC/
INPUT
dts
1
CS
ON
D
RROUND
MODE
AUTO
l/
SLEEP
PRESET SCAN
The preset channel can be checked on the on screen
display.
ENGLISH
CHECKING THE XM PRESET CHANNEL
PRESET MEMORY
When the desired preset station is received,
cancel the preset scan operation by press the
P. SCAN button.
Notes:
• To clear all stored preset stations, press and hold
the CLEAR (CL) and the ENTER buttons for two
seconds.
• There are 50 preset channels prepared at the factory
default. The 50 channels are all set to “CHANNEL
001”. Each channel can be stored in the preset
memory. You can search for only the preset
channels.
Note:
The preset channel indication disappears in about 5
sec.
47
SR4002-5002U DFU_01_E2_2.indd 47
07.7.9 2:47:43 PM
ENGLISH
MULTI ROOM
SYSTEM (SR5002 only)
The Multi Room system is a function which allows
you to listen to the same or a different source in a
room other than the room in which the SR5002 is
located.
The operations possible with the multi room function
are explained briefly below.
For details, refer to the instruction manual supplied
with the multi room remote controller and SR5002.
MULTI ROOM PLAYBACK USING THE MULTI
ROOM OUT TERMINALS
MULTI ROOM PLAYBACK USING THE MULTI
SPEAKER TERMINALS
The SR5002 is equipped with audio pre-out terminals
for which the volume is adjustable as the MULTI
output terminals.
A separately sold stereo power amplifier can be
connected to enjoy multi room playback.
1. 4. 2.
The SR5002 allows you to connect another set
of speakers and place them in a different room or
separated area for listening to music.
2.
3.
1. 4.
DOWN
UP
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
DISPLAY
SETUP MIC
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
PHONES
UP
L
AUDIO
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
PHONES
AUX 1 INPUT
S-VIDEO
VIDEO
R
0
+10
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
CL
0
CH/ CAT
1. 4.
+10
MEMO
VOLUME
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
3.
1. 4.
MEMO
VOLUME
3.
INFO
MENU
ENTER
INFO
MENU
T.TONE
/SET UP
EXIT
REC
ENTER
T.TONE
/SET UP
T.DISP
-
T.DISP
PTY
PRESET
PRESET
+
-
+
-
TUNING
TUNING
+
ANGLE
SUB TITLE
V-OFF
ATT.
CH-SEL
BASS
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
TV
DVD
VCR
DSS
TUNER
CD
CDR
MD
AUX1
AUX2
AMP
BASS
2.
F.DIRECT
TAPE
+
F.DIRECT
DISC+
-
PTY
EXIT
REC
During this time, you can set the volume level in
the multi room as desired.
This will only set the volume in the multi room.
4.
To cancel this function, press the MULTI button
on the unit or remote controller (after pressing
the AMP button on the remote controller).
ENTER
SETUP MIC
CH/ CAT
CL
3.
ATT
ATT
AUX 1 INPUT
S-VIDEO
VIDEO
Select the input source using the INPUT
SELECTOR knob or function button on the
remote controller.
Then, the display indicates “MSPKR VOLUME”
“MSPKR VOL.–xx” for approx. 5 seconds.
CLEAR
ENTER
AUTO
SR5002 has some feature to MULTI ROOM SYSTEM
as source selector, sleep timer, Multi Room Speaker
output and remote control.
MEMORY
CLEAR
MUTE
STANDBY
POWER ON/STANDBY
MEMORY
SIMPLE
SETUP
MUTE
AUTO
SURROUND
MODE
PURE
DIRECT
STANDBY
POWER ON/STANDBY
MULTI
SPEAKER
2.
VOLUME
VOLUME
MULTI
MULTI
Press the MULTI SPEAKER (M-SPKR) button.
The unit enters multi room speaker mode and
the display indicates “SELCT SOURCE” and
flashes the “MULTI” indicators for approx. 10
seconds.
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
DOWN
When the outputs of the MULTI OUT terminals are
wired and connected to amplifiers installed in other
rooms or M (MULTI) SPEAKER B terminals are
wired and connected to L&R speakers in other room,
different sources can be played in rooms other than
the main room in which the SR5002 and the playback
devices are installed.
3.
1.
AUDIO
2.
TREBLE
1. 4.
AUDIO
TREBLE
TV
DVD
VCR
TUNER
CD
CDR
DSS
MD
TAPE
AUX1
AUX2
AMP
1. 4.
L
AUDIO
R
“MULTI” indicator on the front panel will be
turned off.
Notes for MULTI ROOM SPEAKER
• MULTI ROOM SPEAKER On/ Off is available in
main room only.
• MULTI ROOM SPEAKER output terminals can
be used when the SURROUND BACK SPEAKER
is set NONE in SPEAKER SETUP menu. (See
SPEAKER SETUP, page 27)
• “The Surr. Back Speakers are in use” is displayed
by pressing the MULTI SPEAKER (M-SPKR)
button when the SURROUND BACK SPEAKER is
set except NONE in SPEAKER SETUP menu. (See
SPEAKER SETUP, page 27)
REMOTE CONTROLLER
REMOTE CONTROLLER
48
SR4002-5002U DFU_01_E2_2.indd 48
1.
Press the MULTI button on the unit or remote
controller (after pressing the AMP button
on the remote controller). The unit enters
MULTI ROOM mode, and the display indicates
“SELECT SOURCE.” The “MULTI” indicator will
flash for about 10 seconds.
2.
Select the input source using the INPUT
SELECTOR knob or function button on the
remote controller.
Then, the display indicates “MULTI VOLUME”
“MULTI VOL. xx” for approx. 5 seconds.
3.
During this time, you can set the volume level in
the multi room as desired.
This will only set the volume in the second room.
4.
To cancel this function, press the MULTI button
on the unit or remote controller (after pressing
the AMP button on the remote controller).
“MULTI” indicator on the front panel will be
turned off.
07.7.9 2:47:43 PM
(SR4002 only)
The Surround Speaker B system is a function which
allows you to listen to the same source in a room other
than the room in which the SR4002 is located.
The operations possible with the Surround speaker
function are explained briefly below.
ANOTHER ROOM PLAYBACK USING THE
S (SURROUND) SPEAKER B TERMINALS
The SR4002 allows you to connect another set
of speakers and place them in a another room or
separated area for listening to music.
The SURROUND SPEAKER B system can not be
operated with the supplied remote controller.
1.
ENGLISH
SURROUND
SPEAKER B SYSTEM
2.
AV SURROUND RECEIVER SR4002
INPUT SELECTOR
VOLUME
DOWN
7.1 CH INPUT
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
S.SPEAKER B
UP
MUTE
STANDBY
ATT
ENTER
POWER ON/STANDBY
SETUP MIC
PHONES
MENU
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
1.
Press the S (Surround) SPEAKER B button.
The unit enters surround speaker B mode and
the “SPKR B” will appear on the display.
2.
The volume of S. SPEAKER B is interlocked
with the main volume.
Notes for SURROUND SPEAKER B
• SURROUND SPEAKER B On/ Off is available in
main room only.
• SURROUND SPEAKER B output terminals can be
used when the SURROUND BACK SPEAKER is set
NONE in SPEAKER SETUP menu. (See SPEAKER
SETUP, page 27)
• “The Surr. Back Speakers are in use” is displayed
by pressing the S. SPEAKER B button when the
SURROUND BACK SPEAKER is set except NONE
in SPEAKER SETUP menu. (See SPEAKER SETUP,
page 27)
• Surround Speaker B function is unavailable, while
the unit is 7.1 CH input mode.
49
SR4002-5002U DFU_01_E2_2.indd 49
07.7.9 2:47:44 PM
ENGLISH
TROUBLESHOOTING
SYMPTOM
Can not select EX/ES mode.
In case of trouble, check the following before calling for service:
1.
Are the connections made properly ?
2.
Are you operating the unit properly following the user’s guide ?
3.
Are the power amplifiers and speaker working properly ?
If the unit does not operate properly, check items shown in the following table.
If your trouble cannot be recovered with the remedy actions listed in the following table, malfunction of the
internal circuitry is suspected; immediately unplug the power cable and contact your dealer, nearest Marantz
authorized dealer or the Marantz Service Center in your country.
SYMPTOM
This unit cannot be turned up.
CAUSE
The power plug is not connected.
No sound and picture are output Mute is on.
even when power is on.
The input cable is not connected correctly.
Cancel mute using the remote controller.
See the connection diagram and connect the cables
correctly.
The master volume control is turned all Adjust the master volume.
the way down.
The SOURCE position is wrong.
Select correct position.
REMEDY
Surround center= NONE has been Make the correct setting.
selected in SPEAKERS SIZE SETUP
Input signal is incompatible.
Use 5.1channel source.
Can not select Pro Logic IIx
mode.
Input signal is incompatible.
Use 2 channel Dolby Digital input signal, PCM input
signal or analog input signal.
Can not select Neo:6 mode.
Input signal is incompatible.
Use 2 channel Dolby Digital input signal, PCM input
signal or analog input signal.
Can not select CSII mode.
Input signal is incompatible.
Use 2 channel Dolby Digital input signal, PCM input
signal or analog input signal.
No output to Sub Woofer Out.
Sub-woofer = NONE has been selected in Select Sub-woofer = YES.
SETUP mode.
Noise is produced during DTSencoded CD or laser disc play.
Analog has been selected for input.
Be sure to perform digital connection, select digital
input, then play.
A specific channel does not
produce output.
Nothing recorded on source.
Check the encoded channel on the source side.
FM or AM reception fails.
Antenna connection is incomplete.
Correctly connect the indoor FM and AM antennas to
FM and AM antenna outlets.
Noise is heard during AM
reception.
Reception is affected by other electrical Try changing location where the AM indoor antenna
fields.
is set up.
The radio waves from the broadcasting Install an FM outdoor antenna.
station are weak.
REMEDY
Connect the power plug to the outlet.
CAUSE
No speaker output.
The headphones are connected to the Disconnect the headphones. (Speakers will not output
headphone jack.
sound when headphones are connected.)
Noise is heard during FM
reception.
Incorrect Audio or Video for
selected source.
Input cable connected incorrectly.
Connect the cable correctly by referring to the
connection diagram.
Cannot get programmed station Preset data has been erased.
when the PRESET button is
pressed.
Disconnecting power plug for long periods of time will
erase preset data. If that happens, input the preset
data again.
Incorrect Audio from a channel.
Speaker cable connected incorrectly.
Connect the cable correctly by referring to the
connection diagram.
Control with the remote
controller fails.
Replace all the batteries with new ones.
Remote controller’s function-key setting Select different position from which equipment will
is wrong.
be controlled.
No Audio output from the center The center speaker cable connection is Connect the cable correctly.
channel speaker.
incomplete.
The distance between this unit and the Move closer to this unit.
remote commander is too far.
STEREO has been selected for Surround When STEREO is selected for Surround mode, no
mode.
sound will be output from the center speaker. Set
another Surround mode.
Center = NONE has been selected in Make the correct setting.
SETUP mode.
No Audio output from the
surround speakers.
The surround speaker cable connection Connect the cable correctly.
is incomplete.
Batteries are consumed.
Something is blocking this unit and the Remove offending object.
remote commander.
MRAC is not working.
Headphones are connected.
Disconnect the headphones.
MRAC is going to CANCEL
mode automatically.
Are the speakers set to OFF?
Set SPK A or SPK B to ON.
STEREO has been selected for Surround When STEREO has been selected for Surround
mode.
mode, no sound will be output from the surround
speaker. Set another Surround mode.
Surround = NONE has been selected in Make the correct setting.
SETUP mode.
No Audio output from the
surround back speakers.
The surround back speaker cable Connect the cable correctly.
connection is incomplete.
Surround mode is not EX/ES mode.
Set surround mode EX/ES.
Surround back = NONE has been selected Make the correct setting.
in SPEAKERS SIZE SETUP
50
SR4002-5002U DFU_01_E2_2.indd 50
07.7.9 2:47:44 PM
SYMPTOM
CAUSE
The display does not appear The connected monitor or projector does not support HDCP.
over an HDMI connection.
The HDMI input of on the TV is not on.
REMEDY
• Connect to equipment that supports HDCP.
• Please change the method of connection.
ENGLISH
HDMI
Set HDMI input so that it turns on, as explained in the TV’s instruction manual.
The HDMI output on the source component (DVD, Set Top Box, Set HDMI output so that it turns on, as explained in the source component’s instruction manual.
etc.) is not on.
The HDMI mode is not correctly set on the unit.
Set HDMI input on the FUNC INPUT SETUP menu as explained on page 33.
The HDMI output video resolution of the source component (DVD, Set the resolution so that it matches, as explained in the instruction manuals of both components.
Set Top Box, etc.) does not match the TV specifications.
The device is connected with a non-standard HDMI cable.
A 5 m or shorter cable is recommended to ensure stable operation and prevent image quality
deterioration.
Power to the unit is off. (When the unit is on standby, HDMI Turn on the power to the unit.
connections cannot be turned on.)
The connection between HDMI components was not Shut off and then turn the power back on to the unit, TV and source component.
authenticated.
The SR4002/5002 OSD menu The unit SETUP menu does not support HDMI output.
does not appear over an HDMI
connection.
Use the COMPONENT VIDEO, S-VIDEO or VIDEO output.
Time is needed for the display of The connection is being authenticated between the HDMI There is nothing wrong with the system. Some HDMI devices require time for authentication.
an HDMI connection to appear. devices.
Audio is not played back over an The HDMI audio output of the source component (DVD, Set Top Set the HDMI audio output so that it turns on, as explained in the source component’s instruction
HDMI connection.
Box, etc.) is not on.
manual.
The signal format of the source component (DVD, Set Top Box, Set the HDMI audio output so that it can connect to the unit, as explained in the source component’s
etc.) is not supported by the unit.
instruction manual.
The unit is set to the HDMI audio “THROUGH” mode.
In the “THROUGH” mode, sound is not produced from the unit. Set it to “ENABLE”. (see page 30)
DVD-Audio is not played back The DVD player does not support CPPM, therefore it cannot • Use a DVD-Audio player that supports CPPM.
over an HDMI connection.
output HDMI audio.
• Turn on PCM downsampling on the DVD player.
• Use an analog connection.
Super Audio CD is not played The current HDMI connection does not support Super Audio Use an analog connection.
back over an HDMI connection. CDs.
51
SR4002-5002U DFU_01_E2_2.indd 51
07.7.9 2:47:45 PM
ENGLISH
XM SATELLITE RADIO
7.1 CH INPUT (SR4002)
MULTI (SR5002)
If a problem should arise, first check the following.
ATT
AV SURROUND RECEIVER SR4002
INPUT SELECTOR
1. Are the connections correct?
2. Have you operated the receiver according to the operating instructions?
3. Are the speakers and other components operating properIy?
DOWN
PURE
DIRECT
SIMPLE
SETUP
“ANTENNA” is displayed.
XM terminal and the XM Mini-Tuner and Home Dock is not Check that the connection are correct.
properly connected.
“NO SIGNAL” is displayed.
The signal cannot be received.
Reposition your XM Mini-Tuner and Home Dock.
Contact XM Radio.
Note:
Sometimes, when “PROTECT” is shown on the unit’s display, the standby indicator flashes slowly (twice a second).
When this happens, turn off the unit’s power and remove the power cable. Then follow the procedure described below:
• Check to ensure that the speaker cables connected to the unit have not been connected with + and - connections reversed.
• Check to ensure that the speaker cables connected to the unit are not short-circuiting (check the connections both on the unit and on the speakers).
(Check that the playback volume is not greater than the unit can handle.)
• Check that the playback volume is not greater than the unit can handle.
After completing the above checks, connect the power cable and switch the unit back ON using the remote control.
Then, after reducing the volume, start playback and check that “PROTECT” is not appearing on the display and that there is no problem with speaker connections to the unit or
with sound reproduction.
If the same problem re-occurs, please contact your local service center to have it repaired.
On rare occasions, the unit will go into standby mode with the standby indicator flashing rapidly (eight times a second).
When this happens, it means that some major problem has occurred with the unit.
Quickly disconnect the power cable and take the unit to your local service center to have it repaired.
MEMORY
UP
CLEAR
MUTE
ATT
ENTER
AUTO
REMEDY
DISPLAY
S.SPEAKER B
STANDBY
POWER ON/STANDBY
CAUSE
Receiving only XM channels The XM Tuner is not activated.
0 and 1.
VOLUME
SURROUND
MODE
7.1 CH INPUT
If this unit is not operating properly, Check the items listed in the table beIow. Should the problem persist, there may be a malfunction. Disconnect the power immediately
and contact your store of purchase.
SYMPTOM
SIMPLE
SETUP EXIT
SETUP MIC
HT-EQ
MENU
PHONES
EXIT
BAND
T-MODE
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
FRONT KEY (BUTTON) LOCK OF THE UNIT
If the SIMPLE SETUP and EXT buttons on the front
panel are both pressed at the same time for three
seconds or more, all the buttons on the front panel,
(excluding the POWER ON/OFF button), as well as
the INPUT SELECTOR knob and VOLUME knob,
will become locked. “F-KEY LOCK!” will appear in
the display.
Release the lock by pressing the same two keys
again at the same time for three seconds or more.
“F-KEY UNLOCK” will appear in the display, and the
keys will unlock.
GENERAL MALFUNCTION
If the equipment malfunctions, this may be because
an electrostatic discharge or AC line interference has
corrupted the information in the equipment memory
circuits. Therefore:
-
disconnect the plug from the AC line supply
-
after waiting at least three minutes, reconnect
the plug to the AC line supply
-
re-attempt to operate the equipment
Memory backup
• In case a power outage occurs or the power
cord is accidentally unplugged, this unit is
equipped with a backup function to prevent
memory data such as the preset memory
from being erased.
HOW TO RESET THE UNIT
Should the operation or display seem to be abnormal,
reset the unit with the following procedure.
To turn on the SR4002, press and hold the 7.1CH
INPUT and ATT buttons simultaneously for 3 seconds
or more.
To turn on the SR5002, press and hold the MULTI
and ATT buttons simultaneously for 3 seconds or
more.
Remember that the procedure will reset the settings
of the SOURCE, Surround mode, delay time, TUNER
52
SR4002-5002U DFU_01_E2_2.indd 52
07.7.9 2:47:45 PM
ENGLISH
TECHNICAL SPECIFICATIONS
AUDIO SECTION (SR4002)
Power Output (20 Hz – 20 kHz/THD=0.08%)
Front L&R................................................8 ohms 80 W / Ch
Center .....................................................8 ohms 80 W / Ch
Surround L&R .........................................8 ohms 80 W / Ch
Surround Back L&R ................................8 ohms 80 W / Ch
Front L&R............................................. 6 ohms 105 W / Ch
Center .................................................. 6 ohms 105 W / Ch
Surround L&R ...................................... 6 ohms 105 W / Ch
Surround Back L&R ............................. 6 ohms 105 W / Ch
29/32 ins.
(23 mm)
GENERAL (SR4002)
Power Requirement ....................................AC 120 V 60Hz
Power Consumption ................................................. 450 W
Weight .................................................... 25.1 lbs (11.4 Kg)
GENERAL (SR5002)
Power Requirement ....................................AC 120 V 60Hz
Power Consumption ................................................. 500 W
Weight .................................................... 27.1 lbs (12.3 Kg)
ACCESSORIES
Remote Controller RC5001SR ..........................................1
AAA-size batteries ............................................................ 2
FM Antenna........................................................................1
AM Loop Antenna ..............................................................1
Front AUX Jack Cover .......................................................1
AC Power Cord ..................................................................1
Microphone MC-10 ............................................................1
User Guide .........................................................................1
Warranty Card (USA x 1, Canada x 1)
Input Sensitivity/Impedance..................180 mV/ 47 Kohms
Signal to Noise Ratio(Analog Input / Pure Direct) ....... 105 dB
Frequency Response
(Analog Input / Pure Direct)
..............................................8 Hz – 100 kHz (± 3 dB)
(Digital Input / 96 kHz PCM)
............................................... 8 Hz – 45 kHz (± 3 dB)
17-5/16 ins. (440 mm)
AV SURROUND RECEIVER SR5002
INPUT SELECTOR
VOLUME
DOWN
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
Front L&R..............................................6 ohms 110 W / Ch
Center ...................................................6 ohms 110 W / Ch
Surround L&R .......................................6 ohms 110 W / Ch
Surround Back L&R ..............................6 ohms 110 W / Ch
ATT
SETUP MIC
PHONES
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
9/16 ins.
(14 mm)
Power Output (20 Hz – 20 kHz/THD=0.08%)
Front L&R................................................8 ohms 90 W / Ch
Center .....................................................8 ohms 90 W / Ch
Surround L&R .........................................8 ohms 90 W / Ch
Surround Back L&R ................................8 ohms 90 W / Ch
UP
CLEAR
ENTER
AUTO
POWER ON/STANDBY
MEMORY
MUTE
STANDBY
AUDIO SECTION (SR5002)
DISPLAY
6-5/16 ins.
(160 mm)
Frequency Range ...................................... 520 – 1710 kHz
Signal to Noise Ratio ................................................. 50 dB
Usable Sensitivity.........................................Loop 400µV/m
Distortion ..................................... 400Hz, 30 % Mod. 0.5 %
Selectivity ....................................................± 20 kHz 70 dB
DIMENSIONS
Television Format.......................................................NTSC
Input Level/Impedance ..............................1 Vp-p/75 ohms
Output Level/Impedance ...........................1 Vp-p/75 ohms
Video Frequency Response ..........5 Hz to 8 MHz (– 1 dB)
Video Frequency (Component) .......5 Hz to 80 MHz (– 1 dB)
S/N ............................................................................. 60 dB
13-7/16 ins.
(341 mm)
15-1/8 ins.
(384 mm)
AM TUNER SECTION
VIDEO
13/16 ins.
(20 mm)
Frequency Range ...................................87.5 – 108.0 MHz
Usable Sensitivity ................................IHF 1.8 µV/16.4 dBf
Signal to Noise Ratio ...................... Mono/Stereo 75/70 dB
Distortion ........................................ Mono/Stereo 0.2/0.3 %
Stereo Separation ............................................1 kHz 45 dB
Alternate Channel Selectivity....................± 300 kHz 60 dB
Image Rejection ............................................98 MHz 70 dB
Tuner Output Level ..............1 kHz, ± 75 kHz Dev 800 mV
5-3/4 ins.
(146 mm)
FM TUNER SECTION
Specifications subject to change without prior notice.
Input Sensitivity/Impedance..................180 mV/ 47 Kohms
Signal to Noise Ratio(Analog Input / Pure Direct) ....... 105 dB
Frequency Response
(Analog Input / Pure Direct)
..............................................8 Hz – 100 kHz (± 3 dB)
(Digital Input / 96 kHz PCM)
................................................8 Hz – 45 kHz (± 3 dB)
53
SR4002-5002U DFU_01_E2_2.indd 53
07.7.9 2:47:45 PM
SETUP CODES
TV
Acer .......................................................... 1141
Admiral .................................1002, 1009, 1089
Aiko .......................................................... 1059
Aiwa................................................1117, 1118
Akai .......................................................... 1001
Amtron ...................................................... 1023
Anam ........................................................ 1113
Anam National......................1023, 1069, 1092
AOC........................... 1003, 1024, 1049, 1127
Audiovox ................................................... 1023
Bell & Howell ..................................1009, 1025
Benq ...............................................1104, 1142
Broksonic .................. 1003, 1097, 1098, 1113
Celebrity ................................................... 1001
Citizen ..................................1003, 1013, 1023
1026, 1059, 1063
Colortyme .......................................1003, 1043
Contec ...................................................... 1113
Contec/Cony ........................1023, 1045, 1047
Craig .......................... 1020, 1022, 1023, 1113
Crown .............................................1023, 1067
Curtis Mathes .......................1003, 1013, 1025
1026, 1062, 1103, 1110
Daewoo ..................... 1003, 1013, 1024, 1035
1036, 1059, 1084, 1101
Daytron .................................1003, 1013, 1016
Dimensia ........................................1103, 1110
Dumont .................................1003, 1010, 1153
Electroband .............................................. 1001
Electrohome .............. 1001, 1003, 1069, 1133
Emerson ...............................1003, 1013, 1015
1020, 1021, 1022, 1023
1025, 1038, 1044, 1045
1048, 1055, 1061, 1094
1096, 1099, 1101, 1113
Envision .................................................... 1003
Fisher ........................ 1025, 1051, 1091, 1160
Fujitsu ........................ 1038, 1124, 1125, 1155
Funai ....................................1023, 1038, 1113
Gateway ................................................... 1150
GE ............................ 1003, 1018, 1022, 1046
1054, 1069, 1085, 1103
1110, 1113, 1133, 1136, 1153
Goldstar ................................1003, 1013, 1024
1030, 1045, 1080
1100, 1112, 1154
Hallmark ................................................... 1003
Hisense .................................................... 1116
Hitachi ....................... 1003, 1012, 1031, 1032
1037, 1041, 1045, 1047
1065, 1068, 1082, 1088
1094, 1139, 1140, 1145, 1159
Infinity ....................................................... 1067
Janeil ........................................................ 1134
JBL ........................................................... 1067
JC Penney ............................1003, 1013, 1018
1019, 1024, 1026
1046, 1047, 1054
1063, 1083, 1085
1100, 1103, 1110
1112, 1133, 1154
Jensen ...................................................... 1003
JVC.......................................1028, 1029, 1045
1047, 1050, 1060, 1065
Kawasho.........................................1001, 1003
Kenwood .................................................. 1003
Kloss Novabeam ....... 1023, 1056, 1057, 1134
KTV ......................................1013, 1023, 1033
1034, 1073, 1099, 1113
LG...................................................1024, 1030
M.Wards ...............................1002, 1009, 1038
Magnavox .............................1003, 1052, 1053
1056, 1057, 1063
1067, 1081, 1106
Marantz ..................... 1003, 1031, 1067, 1122
Mitsubishi .............................1003, 1024, 1051
1115, 1122, 1133
Motorola .........................................1014, 1069
NEC ................. 1003, 1012, 1024, 1043, 1069
NET-TV ...........................................1137, 1150
Orion...............................................1020, 1096
Panasonic........ 1017, 1067, 1069, 1095, 1111
Philips ........................ 1003, 1011, 1045, 1052
1054, 1056, 1057, 1058
1063, 1067, 1069, 1106
Pioneer .................................1003, 1018, 1037
1070, 1071, 1094
1145, 1147, 1149
Plasmsync ................................................ 1135
Portland ..................... 1003, 1013, 1024, 1059
Price Club................................................. 1026
Prism ........................................................ 1018
Proscan ..................... 1004, 1005, 1006, 1007
1008, 1085, 1103, 1110
Proton .............................................1003, 1045
Quasar ............ 1010, 1069, 1073, 1111, 1153
Radio Shack .........................1003, 1013, 1015
1023, 1024, 1025, 1045
1100, 1103, 1110, 1113
RCA ......................................1003, 1004, 1005
1006, 1007, 1008
1014, 1024, 1049, 1069
1075, 1079, 1085, 1087
1088, 1093, 1094, 1101
1103, 1110, 1113, 1153
Realistic ..................... 1013, 1015, 1023, 1025
1045, 1100, 1103, 1110
Runco .............................................1010, 1153
Sampo ...................................................... 1150
Samsung ................... 1003, 1013, 1024, 1026
1040, 1045, 1062, 1078
1083, 1090, 1100, 11051114
1120, 1121, 1146, 1148, 1157
Sansui ...................................................... 1119
Sanyo ........................ 1003, 1025, 1051, 1072
1077, 1091, 1156, 1157, 1158
Sharp....................................1003, 1013, 1014
1015, 1045, 1055, 1064
1066, 1076, 1089, 1123
Signature .................................................. 1009
Sony .....................................1001, 1102, 1108
Soundesign ..... 1003, 1023, 1038, 1063, 1113
Starlite ...................................................... 1023
Supre-Macy .............................................. 1134
Sylvania ................................1003, 1039, 1042
1052, 1053, 1056, 1057
1063, 1067, 1089, 1151
Symphonic ...........................1023, 1039, 1044
Tandy ........................................................ 1014
Tatung....................................................... 1069
Technics ................................................... 1018
Techwood .......................................1003, 1018
Teknika ...................... 1003, 1009, 1013, 1023
1024, 1026, 1038, 1045
1047, 1059, 1063, 1111, 1113
Telecaption ............................................... 1074
Toshiba .................................1003, 1019, 1025
1026, 1042, 1074, 1098
1107, 1111, 1135, 1136
Totevision ................................................. 1013
Universal ........................................1046, 1054
Video Concepts ........................................ 1113
Viewsonic .............................1006, 1022, 1109
1128, 1129, 1130, 1131
1138, 1143, 1145, 1150
Wards ...................................1003, 1009, 1015
1024, 1038, 1044, 1046
1052, 1054, 1056, 1057
1067, 1086, 1103, 1110
White Westinghouse ......................1001, 1101
Yamaha ..........................................1003, 1024
Zenith ...................................1003, 1009, 1010
1132, 1144, 1153
VCR
Admiral ...........................................3026, 3060
Adventura ................................................. 3035
Aiko .......................................................... 3038
Aiwa................................................3035, 3039
Akai ................................................3003, 3053
3054, 3072, 3073
American High ......................................... 3009
Asha ......................................................... 3021
Audio Dynamics ...................3034, 3040, 3083
Audiovox ................................................... 3052
Beaumark .......................................3017, 3021
Bell & Howell ............................................ 3029
Broksonic .......................................3029, 3075
Calix ......................................................... 3052
Candle ..................................3012, 3021, 3034
3038, 3050, 3052, 3056
Canon .............................................3008, 3009
Capehart .................................................. 3050
Carver.............................................3045, 3062
CCE ................................................3038, 3067
Challenger ................................................ 3078
Citizen ............. 3012, 3021, 3038, 3052, 3056
Colortyme .......................................3034, 3079
Colt ........................................................... 3067
Craig .......................... 3021, 3032, 3052, 3067
Criterion.................................................... 3067
Curtis Mathes .................................3008, 3009
3021, 3034, 3063
Cybernex .................................................. 3021
Daewoo ................................3035, 3038, 3050
Daytron ...........................................3038, 3050
DBX ......................................3034, 3040, 3083
Denon ....................................................... 3005
i
SR4002-5002U DFU_02_setup.indd i
07.7.9 2:48:03 PM
Dimensia ..............................3004, 3063, 3085
Dixon ..............................................3077, 3081
Dynatech .................................................. 3035
Electrohome ............................................. 3052
Electrophonic ........................................... 3052
Emerson .................... 3009, 3015, 3016, 3017
3018, 3019, 3022, 3035
3047, 3052, 3054, 3073
Fisher .............................................3029, 3032
Fuji..................................................3003, 3009
Funai ..............................................3035, 3056
Garrard ..................................................... 3035
GE ........................................3004, 3008, 3009
3021, 3028, 3058
3063, 3074, 3085
Go Video ..............................3021, 3036, 3037
3052, 3067, 3068, 3069
Goldstar ..................... 3021, 3031, 3034, 3052
Gradiente .......................................3035, 3052
Harley Davidson ....................................... 3035
Harman Kardon..............................3034, 3045
Harwood ................................................... 3067
Headquarter ............................................. 3029
Hitachi ............. 3004, 3005, 3055, 3072, 3074
Homeline .................................................. 3052
Instant Replay .......................................... 3009
JBL ........................................................... 3002
JC Penney ................. 3005, 3008, 3009, 3017
3021, 3029, 3034, 3040
3052, 3062, 3067, 3083
JCL ........................................................... 3009
Jensen ............................................3005, 3072
JVC.......................................3014, 3015, 3034
3040, 3041, 3042
3048, 3049, 3072, 3083
Kenwood ................... 3029, 3034, 3048, 3072
KLH .......................................................... 3067
Kodak .............................................3009, 3052
LG...................................................3031, 3052
Lloyds ...................................3034, 3035, 3056
Logik ......................................................... 3067
LXI ............................................................ 3052
Magnasonic ..........................3038, 3052, 3067
Magnavox .............................3008, 3009, 3010
3045, 3067, 3071
Magnin ...........................................3021, 3052
Marantz ................................3009, 3029, 3034
3040, 3045, 3062, 3083
Marta ........................................................ 3052
MEI ........................................................... 3009
Memorex ..............................3005, 3009, 3021
3026, 3029, 3032, 3035
3052, 3060, 3067, 3071
MGA ...............................................3022, 3073
MGN Technology...................................... 3021
Midland ..................................................... 3056
Minolta ...................................................... 3005
Mitsubishi .............................3005, 3022, 3023
3025, 3048, 3052, 3073
Montgomery Ward..........................3026, 3060
Motorola ...............................3009, 3026, 3060
MTC................................................3021, 3067
Multitech ...............................3021, 3035, 3067
NEC ......................................3033, 3034, 3040
3048, 3072, 3083
Nikko ........................................................ 3052
Noblex ...................................................... 3021
Olympus ................................................... 3009
Optimus ................................3026, 3052, 3060
Optonica ................................................... 3027
Orion.......................... 3015, 3017, 3047, 3052
Panasonic........ 3006, 3007, 3008, 3009, 3067
Pentax ..................................3005, 3034, 3074
Philco............... 3005, 3008, 3009, 3047, 3062
Philips .............. 3009, 3010, 3027, 3045, 3062
Pilot .......................................................... 3052
Pioneer .................................3005, 3040, 3046
3048, 3061, 3080, 3083
Portland .................................................... 3050
Proscan ................................3004, 3063, 3085
Protec ....................................................... 3067
Proton ....................................................... 3067
Pulsar ........................ 3021, 3038, 3056, 3071
Quarter ...........................................3029, 3084
Quartz ............................................3029, 3084
Quasar ...........................................3008, 3009
Radio Shack .............. 3021, 3052, 3009, 3008
3035, 3027, 3060, 3026
Radix ........................................................ 3052
Randex ..................................................... 3052
RCA ......................................3004, 3005, 3009
3021, 3046, 3054, 3057
3061, 3063, 3074, 3085
Realistic ..................... 3008, 3009, 3012, 3021
3026, 3027, 3029, 3032
3035, 3052, 3060, 3084
Ricoh ..............................................3002, 3059
Runco ....................................................... 3071
Samsung ..............................3013, 3020, 3021
3056, 3068, 3069, 3070
Sanky ...................................3026, 3060, 3071
Sansui ............. 3040, 3048, 3067, 3072, 3083
Sanyo ...................................3021, 3029, 3032
Scott .......................... 3012, 3017, 3022, 3052
Sears ....................................3005, 3009, 3029
3032, 3034, 3052, 3084
Sharp......................... 3026, 3027, 3060, 3064
Shintom ................................3003, 3005, 3067
Shogun ..................................................... 3021
Signature ........................................3026, 3060
Signature 2000 .....................3026, 3029, 3084
Singer ........................ 3002, 3009, 3059, 3067
Sony .......................... 3001, 3003, 3043, 3065
STS ................................................3005, 3009
Sylvania ................................3008, 3009, 3022
3035, 3045, 3062, 3076
Symphonic ...........................3034, 3035, 3056
Tandy ..............................................3029, 3084
Tashiko ..................................................... 3052
Tatung....................................................... 3072
Teac ................................................3035, 3072
Technics .........................................3007, 3009
Teknika .................................3009, 3035, 3052
TMK .......................................................... 3021
Toshiba .................................3005, 3011, 3012
3022, 3051, 3073
Totevision .......................................3021, 3052
Unitec ....................................................... 3056
Unitech ..................................................... 3021
Vector Research........ 3012, 3034, 3040, 3083
Victor ..............................................3040, 3083
Video Concepts ..............................3012, 3034
3040, 3073, 3083
Videosonic................................................ 3021
Wards ...................................3005, 3009, 3012
3021, 3026, 3027
3032, 3035, 3045
3052, 3060, 3061, 3067
White Westinghouse ......................3035, 3056
XR-1000 ...............................3009, 3035, 3067
Yamaha ................................3029, 3034, 3040
3072, 3083, 3084
Zenith .............. 3030, 3052, 3053, 3059, 3071
DVD
Aiwa................................................2036, 2037
Apex ...... 2012, 2017, 2018, 2019, 2021, 2034
BOSE .............................................2038, 2039
Denon .............................................2047, 2048
Funai ........................................................ 2049
GE ............................. 2009, 2020, 2029, 2033
Harman Kardon........................................ 2061
Hitachi ..................................2008, 2012, 2031
JVC.......................................2006, 2010, 2040
2041, 2042, 2043
Kenwood ........................................2053, 2054
Koss.......................................................... 2058
Magnavox .................. 2007, 2011, 2023, 2025
Marantz .................................................... 2025
Mitsubishi .......................................2011, 2015
Onkyo ....................................................... 2062
Oritron ............................................2009, 2030
Panasonic.................. 2003, 2015, 2016, 2055
Philips ...................................2007, 2011, 2058
Pioneer .................................2002, 2014, 2056
Proscan ................................2009, 2020, 2032
RCA ................. 2005, 2009, 2020, 2035, 2057
Sampo ...................................................... 2041
Samsung ......... 2008, 2012, 2022, 2024, 2027
Sanyo .............................................2050, 2052
Sharp..............................................2044, 2045
Sherwood ................................................. 2051
Sony .....................................2001, 2013, 2059
Toshiba ...................... 2004, 2008, 2026, 2028
Yamaha ..........................................2046, 2060
Zenith ....................................................... 2010
DSS
Alphastar .................................................. 4027
BSB .......................................................... 4021
Chaparral ................................................. 4039
DIRECTV .......................................4001, 4016
DISH Network .......................................... 4030
Drake ........................................................ 4026
Echostar .......... 4007, 4017, 4018, 4019, 4020
Express Vu ............................................... 4017
Fujitsu ....................................................... 4025
GE ........................................4002, 4008, 4009
General Instruments ......................4036, 4037
Hitachi ............................................4001, 4015
ii
SR4002-5002U DFU_02_setup.indd ii
07.7.9 2:48:03 PM
Hughes ...........................................4001, 4016
Janeil ........................................................ 4025
JVC........................................................... 4017
Mitsubishi ................................................. 4001
Panasonic.......................................4004, 4010
Philips .............................................4031, 4035
Proscan ..................... 4002, 4008, 4009, 4011
Radio Shack ...................................4036, 4037
RCA ........................... 4002, 4008, 4009, 4029
Realistic .................................................... 4040
Rural Cable .............................................. 4036
Samsung ........................................4022, 4027
Sony .....................................4003, 4012, 4014
Star Choice .............................................. 4032
Star Trak ................................................... 4024
STS .......................................................... 4038
SuperDish ................................................ 4028
Toshiba ...........................................4001, 4034
Uniden ..................................4005, 4006, 4013
Video Pall ................................................. 4025
Zenith .............................................4025, 4033
iii
SR4002-5002U DFU_02_setup.indd iii
07.7.9 2:48:04 PM
www.marantz.com
You can find your nearest authorized distributor or dealer on our website.
is a registered trademark.
Printed in China
SR4002-5002U DFU_02_setup.indd iv
07/2007
00M32CW851250
mzh-d
07.7.9 2:48:04 PM
Download PDF