Regency Fireplace Products | P36D-LP1 | Installation manual | Regency Fireplace Products P36D-LP1 Installation manual

P36D-1 Zero Clearance
Direct Vent Gas Fireplace
MODELS:
P36D-NG1 Natural Gas
P36D-LP1 Propane
Owners & Installation Manual
www.regency-fire.com
WARNING:
If the information in these instructions are not followed exactly, a fire or
explosion may result causing property damage, personal injury or loss
of life.
FOR YOUR SAFETY
What to do if you smell gas:
 Do not try to light any appliance
 Do not touch any electrical switch: do not
use any phone in your building.
FOR YOUR SAFETY
 Immediately call your gas supplier from a
Do not store or use gasoline or other flammable vapors and liquids in the
neighbour's phone. Follow the gas
vicinity of this or any other appliance.
supplier's instructions.
Installation and service must be performed by a qualified installer, service  If you cannot reach your gas supplier, call
the fire department.
agency or the gas supplier.
Tested by:
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
918-522c
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
10/28/13
To the New Owner:
Congratulations!
You are the owner of a state-of-the-art Gas Fireplace by REGENCY® FIREPLACE PRODUCTS The P36D-1 is a hand crafted appliance and has been designed to provide you with
all the warmth and charm of a wood fireplace at the flick of a switch. The model P36D-1
has been approved by Warnock Hersey for both safety and efficiency. As it also bears our
own mark, it promises to provide you with economy, comfort and security for many trouble
free years to follow. Please take a moment now to acquaint yourself with these instructions
and the many features of your REGENCY®Fireplace.
2
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE
This REGENCY® product has been tested and listed by Warnock Hersey to the following standards: VENTED GAS FIREPLACE HEATERS ANSI Z21.88a-2007/
CSA 2.33a-2007 and GAS-FIRED APPLIANCES FOR USE AT HIGH ATLITUDES CAN/CGA 2.17-M91.
This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions and the Manufactured Home Construction
and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufactured Home Installations, Sites, and Communities
ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada.
This appliance installation must comply with the manufacturer's installation instructions and local codes, if any. In the absence of local codes follow the current
National Fuel Gas Code, ANSI Z223.1 and the current National Electrical Code ANSI/NFPA 70 in the U.S.A., and the current CAN/CGA B149 Gas Installation
Code and the current Canadian Electrical Code CSA C22.1 in Canada.
This FPI Mobile/Manufactured Home Listed appliance comes
factory equipped with a means to secure the unit.
This FPI Mobile/Manufactured Home listed appliance comes
equipped with a dedicated #8 ground lug to which an 18
gauge copper wire from the steel chassis ground must be
attached.
This appliance may only be installed in an aftermarket
permanently located, manufactured (mobile) home,
where not prohibited by local codes.
This appliance is only use with the type of gas indicated
on the rating plate. This appliance is not convertible for
use with other gases, unless a certified kit is used.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
3
TABLE OF CONTENTS
SAFETY LABEL
Copy of Safety Decal for P36D-1 ..................................6
REQUIREMENTS
MA Code - CO Detector.................................................7
INSTALLATION
Unit Dimensions ............................................................8
Before You Start ............................................................9
Important Message .....................................................10
General Safety Information..........................................10
Installation Checklist ...................................................10
Locating Your
Gas Fireplace .............................................................. 11
Manufactured Mobile Home Additional Requirements 11
Heatwave Duct System (Optional) ............................. 11
Heat Release kit (Optional) ........................................ 11
Clearances ..................................................................12
Regency® Clearances ..........................................13
Tripoli Arch Door Clearances ...............................13
Regency® Combustible Mantel Clearances ................14
Regency® Mantel Leg Clearances ...............................16
Framing And Finishing .................................................17
Tripoli Arch Door Framing Note ...................................18
Unit Assembly Prior To Installation ..............................19
Top Standoff Assembly ........................................19
Top Facing Support &
Side Nailing Strips ...............................................19
Vertical Termination .....................................................26
Horizontal Venting with Two (2) 90o Elbows ................28
Horizontal Venting with Three (3) 90o Elbows .............28
Vertical Venting with Two (2) 90o Elbows.....................29
Vertical Venting with Three (3) 90o Elbows ..................29
Vertical Termination
With Co-linear Flex System .........................................30
Venting Arrangement - Vertical Terminations ..............31
unit installation with Horizontal termination .................32
unit installation with Vertical Termination .....................33
Direct Vent System (Flex)
Installation Procedures ................................................34
P36D-NG1 System Data ............................................35
P36D-LP1 System Data .............................................35
High Elevation .............................................................35
Gas Line Installation ....................................................35
Pilot Adjustment ...........................................................35
Gas Pipe Pressure Testing ..........................................35
S.I.T. Valve Description................................................35
Conversion from NG to LP ..........................................36
Optional Brick Panels ..................................................39
Log Set Installation ......................................................41
Standard Flush Door ...................................................44
Remote Control (Optional)...........................................45
Wall Switch (Optional) .................................................45
Wall Thermostat (Optional) .........................................45
Wiring Diagrams .........................................................46
Optional Fan Installation ..............................................48
Optional Fan Removal .................................................48
Venting Introduction .....................................................19
Exterior Vent Termination Locations ............................20
Venting.........................................................................21
Direct Vent System (Flex) ..................................21
4” x 6-5/8” Rigid Pipe Cross Reference Chart .............22
Rigid Pipe Venting Systems.................................24
Venting Arrangements Horizontal Termination ............25
Venting Arrangements
NOTE: All installation instructions apply to
Regency® Series unless otherwise specified.
4
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
TABLE OF CONTENTS
OPERATING INSTRUCTIONS
Operating Instructions .................................................49
Shutdown Procedure ..................................................49
First Fire ......................................................................49
Lighting Procedure ......................................................49
Aeration Adjustment ....................................................49
Normal Operating Sounds Of Gas Appliances ............49
Copy of the Lighting Plate Instructions ........................50
MAINTENANCE
Maintenance Instructions.............................................50
General Vent Maintenance ..........................................51
Log Replacement ........................................................51
Thermopile/
Thermocouple..............................................................51
Glass Gasket ...............................................................51
Door Glass...................................................................51
Flush Glass Replacement....................................51
Removing Valve...........................................................52
Installing Valve.............................................................52
Flush Louvers ..............................................................53
Full Screen door Installation .....................................54
Tripoli screen door .......................................................56
PARTS LIST
Main Assembly ............................................................59
Burner Assembly & Log Set.........................................60
Regency® Flush Front Assembly .................................61
WARRANTY
The Warranty: Limited Lifetime ...................................71
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
5
SAFETY LABEL
This is a copy of the label that accompanies each P36D-1 Zero Clearance Direct Vent Gas Fireplace. We have printed a copy of the contents here for your
review. The safety label is located on the front inside base of the unit, visible when the bottom louver is open.
NOTE: FPI units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.
COPY OF SAFETY DECAL FOR P36D-1
Duplicate S/N
Listed: VENTED GAS FIREPLACE HEATER / FOYER AU GAZ À ÉVACUATION
Certified for/Certifiée pour: CANADA and U.S.A.
Tested to: CGA-2-17-M91, ANSI Z21.88a-2007 / CSA 2.33a-2007
WN# 16462
306
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ÉTIQUETTE
Serial No./ No de serie
306
MAY BE INSTALLED IN MANUFACTURED (MOBILE) HOMES AFTER FIRST SALE.
Model/Modele:
P36D-LP1
PROPANE: Model P36D-LP1
L
Minimum supply pressure 12"
Manifold pressure high
11"
Manifold pressure low
2.9"
Orifice size
# 52
Minimum input
15,000
Maximum input
30,000
0-4500
Altitude
APPAREIL FONCTIONNANT AU GAZ PROPANE
CONCU POUR ETRE POELE: Modéle P36D-LP1
Pression d'allimentation minimum
WC(3.00 kPa)
Pression à la tubulure d'échappement élevée
WC(2.74 kPa)
Pression à la tubulure d'échappement basse
WC(0.72 kPa)
Grandeur de l'injecteur
DMS
Btu/h (3.96 kW) Débit Calorifique minimum selon
Btu/h (7.91 kW) Débit Calorifique maximum selon
ft/pi(0-1372 m)
l'altitude
Minimum Clearances to Combustibles /
Degagement Minimum De Materiaux Combustibles
Ceiling
0" Clearance to
combustibles from:
Top, sides, bottom and rear of unit
32"
Wall
APPAREIL FONCTIONNANT AU NATURAL GAZ
CONCU POUR ETRE POELE: Modéle P36D-NG1
Pression d'allimentation minimum
WC(1.25 kPa)
Pression à la tubulure d'échappement élevée
WC(0.95 kPa)
Pression à la tubulure d'échappement basse
WC(0.27 kPa)
Grandeur de l'injecteur
DMS
Btu/h (4.54 kW) Débit Calorifique minimum selon
Btu/h (8.79 kW) Débit Calorifique maximum selon
ft/pi(0-1372 m)
l'altitude
A
B
B
Wall
Model/Modele:
P36D-NG1
NATURAL GAS: Model P36D-NG1
L
Minimum supply pressure 5"
Manifold pressure high
3.8"
Manifold pressure low
1.1"
Orifice size
# 37
Minimum input
15,500
Maximum input
30,000
0-4500
Altitude
Mantel Clearances from Top:
(A) Min. 7" (177mm)
Side Wall Clearance
from Side Facing
B) 6" with Flush or Bay Front
B) 8" with Barcelona Trim
Alcove approved for
Bay & Flush Louvers.
The "Bay Louvers" MUST be
used with the Bay Glass option
DOOR SEAL: Please
check that the door is
properly sealed
(See Instruction Manual for
detailed instructions)
Alcove Clearances:
Max. Depth 36" (914mm)
Min. Width 48" (1219mm),
Min. Height 72" (1229mm)
Minimum Vent Clearances:
Horizontal Top
2-1/2" (64mm)
Horizontal Side
1-1/2" (38mm)
Horizontal Bottom 1-1/2" (38mm)
This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas and Propane Installation Code, CSA B149.1.
This appliance must be installed in accordance with the Standard CAN/CSA Z240 MH, Mobile Housing, in Canada, or with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United
States, or when such a standard is not applicable, ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard or ANSI A119.2 ou NFPA 501C Standard for Recreational Vehicles
This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured (mobile) home where not prohibited by local codes. See owner's manual
for details. Fan (Part # 432-917) Optional Bay Window (Part #510-930) Option: HeatWave Kit # 946-556
Installer l'appareil selon les codes ou règlements locaux, ou, en l'absence de tels règlements, selon les codes d'installation ANSI Z223.1, National Fuel Gas Code ou CSA-B149.1 en vigueur.
Installer l'appareil selon la norme CAN/CSA-Z240, Série MM, Maison mobiles ou CAN/CSA-Z240 VC, Véhicules de camping, ou la norme 24 CFR Part 3280, Manufactured Home Construction and Safety Standard. Si ces
normes ne sont pas pertinentes, utilisez la norme ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard, ou ANSI A119.2 ou NFPA 501C Standard for Recreational Vehicles.
Cet appareil doit être utilize uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison préfabriquée ou mobile (É.-U. seulement) installée à demeure si les règlements
locaux le permettent. Voir la notice de l'utilisateur pour plus de renseignements. Cet appareil ne peut pas être utilisé avec d'autres gaz sauf si une trousse de conversion certifiée est fournie.
This vented gas fireplace heater is not for use with air filters.
Ne pas utiliser de filtre à air avec ce foyer au gaz à évacuation.
Made in Canada/
Pour utilisation uniquement avec les portes en verre certifiées avec l'appareil
For use with glass doors certified with the appliance only
Fabrique au Canada
Electrical supply / Électrique 115VAC, 1.13 A, 60Hz.
FPI Fireplace Products International Ltd.Delta, BC, Canada
VENTED GAS FIREPLACE HEATER -NOT FOR USE WITH SOLID FUELS.
FOYER AU GAZ À ÉVACUATION -NE PAS UTILISER AVEC DU COMBUSTIBLE SOLIDE.
918-500a
For the State of Massachusetts, installation
and repair must be done by a plumber or
gasfitter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, flexible
connectors shall not exceed 36 inches in
length.
For the State of Massachusetts, the appliances individual manual shut-off must be a
t-handle type valve.
The State of Massachusetts requires the
installation of a carbon monoxide alarm in
accordance with NFPA 720 and a CO alarm
with battery back up in the same room where
the gas appliance is installed.
6
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
REQUIREMENTS
MA Code - CO Detector
(for the State of Massachusetts only)
5.08: Modifications to NFPA-54, Chapter 10
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than
seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is
installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery
operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of
thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The
sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL
OBSTRUCTIONS".
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR
5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by
the Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or
structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the
instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
"special venting systems", the following requirements shall be satisfied by the manufacturer:
1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and
2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of
the installation.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
7
INSTALLATION
UNIT DIMENSIONS
33"(838mm)
36"(914mm)
8
32-1/2"(826mm)
37"(940mm)
30-1/2"(775mm)
37"(940mm)
36" (914mm)
17-1/8"(435mm)
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
BEFORE YOU START
Safe installation and operation of this appliance
requires common sense, however, we are required
by the Canadian Safety Standards and ANSI
Standards to make you aware of the following:
INSTALLATION AND REPAIR SHOULD
BE DONE BY AN AUTHORIZED
SERVICE PERSON. THE APPLIANCE
SHOULD BE INSPECTED BEFORE
USE AND AT LEAST ANNUALLY BY A
PROFESSIONAL SERVICE PERSON.
MORE FREQUENT CLEANING MAY
BE REQUIRED DUE TO EXCESSIVE
LINT FROM CARPETING, BEDDING
MATERIAL, ETC. IT IS IMPERATIVETHAT
CONTROL COMPARTMENTS, BURNERS
AND CIRCULATING AIR PASSAGEWAYS
OF THE APPLIANCE BE KEPT CLEAN.
YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN THEY ARE
IN THE SAME AREA AS THE APPLIANCE. TODDLERS, YOUNG CHILDREN
AND OTHERS MAY BE SUSCEPTIBLE
TO ACCIDENTAL CONTACT BURNS. A
PHYSICAL BARRIERS IS RECOMMENDED IF THERE ARE AT RISK INDIVIDUAL
IN THE HOUSE. TO RESTRICT ACCESS
TO A FIREPLACE OR STOVE, INSTALL
AN ADJUSTABLE SAFETY GATE TO
KEEP TODDLERS, YOUNG CHILDREN
AND OTHER AT RISK INDIVIDUALS OUT
OF THE ROOM AND AWAY FROM HOT
SURFACES.
CLOTHING OR OTHER FLAMMABLE
MATERIAL SHOULD NOT BE PLACED
ON OR NEAR THE APPLIANCE.
DUE TO HIGH TEMPERATURES, THE
APPLIANCE SHOULD BE LOCATED
OUT OF TRAFFIC AND AWAY FROM
FURNITURE AND DRAPERIES.
WARNING: FAILURE TO INSTALL THIS
APPLIANCE CORRECTLY WILL VOID
YOUR WARRANTY AND MAY CAUSE A
SERIOUS HOUSE FIRE.
CHILDREN AND ADULTS SHOULD BE
ALERTED TO THE HAZARDS OF HIGH
SURFACE TEMPERATURES, ESPECIALLY THE FIREPLACE GLASS, AND
SHOULD STAY AWAY TO AVOID BURNS
OR CLOTHING IGNITION.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
9
INSTALLATION
IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
The P36D-NG1 or P36D-LP1 Direct Vent Fireplace
must be installed in accordance with these
instructions. Carefully read all the instructions in
this manual first. Consult the "authority having
jurisdiction" to determine the need for a permit prior
to starting the installation. It is the responsibility of
the installer to ensure this fireplace is installed in
compliance with manufacturer's instructions and
all applicable codes.
GENERAL SAFETY
INFORMATION
1) The appliance installation must conform with
local codes or, in the absence of local codes, with
the current Canadian or National Gas Codes,
CAN1-B149 or ANSI Z223.1 Installation Codes.
2) The appliance when installed, must be
electrically grounded in accordance with local
codes, or in the absence of local codes with the
current National Electrical Code, ANSI/NFPA 70
or CSA C22.1 Canadian Electrical Code.
3) See general construction and assembly
instructions. The appliance and vent should be
enclosed.
4) This appliance must be connected to the
specified vent and termination cap to the outside
of the building envelope. Never vent to another
room or inside a building. Make sure that the
vent is fitted as per Venting instructions.
to inspect this appliance annually. Make it a practice
to have all of your gas appliances checked
annually.
INSTALLATION
CHECKLIST
13) Do not slam shut or strike the glass door.
14) Under no circumstances should any solid fuels
(wood, paper, cardboard, coal, etc.) be used in
this appliance.
1) Locate appliance
a) Room location (Refer to "Locating Your Gas
fireplace" section)
b) Clearances to Combustibles (Refer to
"Clearances" section)
c) Mantle Clearances (Refer to "Combustible
Mantel Clearances" section)
d) Framing & Finishing Requirements (Refer
to "Framing & Finishing" section)
e) Venting Requirements (Refer to "Venting"
section)
15) The appliance area must be kept clear and
free of combustible materials, (gases and other
flammable vapours and liquids).
Emissions from burning wood or gas could
contain chemicals known to the State of
California to cause cancer, birth defects or
other reproductive harm.
2) Assemble Top Standoffs and Top Facing
Support and Side Nailing Strips (Refer to "Unit
Assembly Prior to Installation" Section). NOTE:
Must be done before installing unit into place.
3) Install vent (Refer to "Venting" sections).
4) Make gas and electrical connections. Test the
pilot. Must be as per diagram (Refer to "Pilot
Adjustment " section).
Convert to propane if desired (Refer to "Gas
Line Installation" and "Conversion Kit from NG
to LPG" sections).
5) Install standard and optional features. Refer
to the following sections:
a. Optional Brick Panels
b. Log Set Installation
c. Standard Flush Door
d. Regency® Flush
e. Remote Control (Optional)
f. Wall Switch (Optional)
g. Wall Thermostat (Optional)
h. Optional Fan Installation
6) Final check.
5) Inspect the venting system annually for blockage
and any signs of deterioration.
6) Venting terminals shall not be recessed into a
wall or siding.
7) Any safety glass removed for servicing must be
replaced prior to operating the appliance.
8) To prevent injury, do not allow anyone who is
unfamiliar with the operation to use the fireplace.
9) Wear gloves and safety glasses for protection
while doing required maintenance.
10) Be aware of electrical wiring locations in walls
and ceilings when cutting holes for termination.
11) Under no circumstances should this appliance
be modified. Parts that have to be removed for
servicing should be replaced prior to operating
this appliance.
12) Installation and any repairs to this appliance
should be done by a qualified service person.
A professional service person should be called
10
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
This includes:
MANUFACTURED
MOBILE HOME
ADDITIONAL
REQUIREMENTS
1) Clocking the appliance to ensure the correct
firing rate (rate noted on label 30,000 Btu/h)
after burning appliance for 15 minutes.
2) If required, adjusting the primary air to ensure
that the flame does not carbon. First allow
the unit to burn for 15-20 min. to stabilize.
1) Ensure that structural members are not cut
or weakened during installation.
CAUTION: Any alteration to the product that
causes sooting or carboning that results
in damage is not the responsibility of the
manufacturer.
2) Ensure proper grounding using the #8
ground lug provided. See "Wiring Diagram"
section.
LOCATING YOUR
GAS FIREPLACE
Diagram 1
1) When selecting a location for your fireplace,
ensure that the clearances outlined on this
page are met.
A)
B)
C)
D)
Flat on Wall
Flat on Wall Corner
Recessed into Wall/Alcove
Corner
2) P r o v i d e a d e q u a t e c l e a r a n c e s f o r
servicing.
3) The appliance must be installed on a flat,
solid, continuous surface (e.g. wood, metal,
concrete). This may be the floor, or raised up
on a platform to enhance its visual impact.
If the appliance is going to be installed
on carpeting, combustible linoleum tile or
other combustible material other than wood
flooring, the appliance must be installed on
a metal or wood panel extending the full
width and depth of the appliance.
4) The P36D-1 Direct Vent Gas Fireplace
can be installed in a recessed position or
framed out into the room as in A, B, C, D.
See Diagram 1.
HEATWAVE
DUCT SYSTEM
(OPTIONAL)
#946-556
5) This appliance is Listed for bedroom
installations when used with a Listed Millivolt
Thermostat. Some areas may have further
requirements, check local codes before
installation.
The HeatWave Air Duct Kit increases the
effectiveness of your fireplace by dispersing
warm air from the fireplace to remote locations in
the same room or other rooms in your home.
6) The P36D-1 Direct Vent Gas Fireplace is
approved for alcove installations, which meet
the clearances listed on the next page.
Up to two kits may be installed on the fireplace.
Please Note: Only 1 HeatWave kit may be
operated at one time. This includes the internal
blower option as well.
7) We recommend that you plan your installation
on paper using exact measurements for
clearances and floor protection before
actually installing this appliance. Have a
qualified inspector, dealer, or installer review
your plans before installation.
Note: For vent terminations see "Exterior
Vent Termination Location" section.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
HEAT RELEASE KIT
(OPTIONAL)
#946-570
The Heat Release Kit expels warm air from
the fireplace to the outside of the building,
allowing the fireplace to be operated with less
heat entering the room. The kit may be used
on either the left or right side.
11
INSTALLATION
CLEARANCES
The clearances listed below are Minimum distances unless otherwise stated:
A major cause of chimney related fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest
importance that this fireplace and vent system be installed only in accordance with these instructions.
Clearance to Combustibles from:
Back
Side
Floor
0"
0"
0"
(0mm)
(0mm)
(0mm)
NOTE: The minimum floor clearance must be maintained from the top surface of the carpeting, tile, etc.
Minimum Clearance from Top of Unit to:
Ceiling from top of unit.
32" (1016mm)
Side Wall Clearances:
Flush Front
Full Screen Doors
6"*
6"*
(152mm)
(152mm)
* Measured from Surround or Front. See Regency® Clearances section for dimensions.
Horizontal Vent Clearances:
Top
Side
Bottom
2"
(51mm)
1-1/2" (38mm)
1-1/2" (38mm)
Vertical Vent Clearances
1-1/4" (32mm)
Alcove Clearances**:
Max. Depth
Min. Width
Min. Height
36"
48"
72"
(914mm)
(1219mm)
(1829mm)
WARNING: Fire hazard is an extreme risk if these clearances are not adhered to.
Heat Release Kit
12
The HeatWave Duct Kit and the Heat
Release Kit have different clearance
and framing requirements, check the
HeatWave and Heat Release manual
for details.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
REGENCY® CLEARANCES
Note: No Hearth Required.
Clearances for Flush Front
& Full Screen Doors
TRIPOLI ARCH DOOR CLEARANCES
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
13
INSTALLATION
REGENCY® COMBUSTIBLE MANTEL CLEARANCES
Because of the extreme heat this fireplace emits, the mantel clearances are critical.
Combustible mantel clearances from top of unit are shown in Diagram 1.
Note: A non-combustible mantel may be installed at a lower height if the framing is made of metal studs covered with a non-combustible board.
Mantel Clearances with
Flush Glass / Full Screen Doors
10
8
6
4
2
0
12
16
Drywall
12" Mantel
14
12
7 1/2" Mantel
10
14"
3 1/2"
Mantel
8
6
10"
7"
2
0
30-1/2"
to floor
6" Standoff
4
Top of
Unit
Side View
Diagram 1
These drawings are to scale at 1:6 (one inch = 6 inches)
Mantel can be installed anywhere in shaded area or higher using the above scale.
Note: Ensure the paint that is used on the mantel and the facing is "heat resistant" or the paint may discolour.
14
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
REGENCY® SERIES COMBUSTIBLE MANTEL CLEARANCES
Because of the extreme heat this fireplace emits, the mantel clearances are critical.
Combustible mantel clearances from top of unit are shown in the diagram below.
Note: A non-combustible mantel may be installed at a lower height if the framing is made of metal studs covered with a non-combustible board.
These drawings are to scale at 1:6 (one inch = 6 inches)
Mantel can be installed anywhere in shaded area or higher using the above scale.
Note: Ensure the paint that is used on the mantel and the facing is "heat resistant" or the paint may discolour.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
15
INSTALLATION
REGENCY® MANTEL LEG CLEARANCES
Combustible mantel leg clearances as per diagram:
Maximum 1-1/2" projection
at 2" minimum clearance.
16
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
FRAMING AND FINISHING
1) Determine the total thickness of facing
material (e.g. drywall plus ceramic tiles) to
allow the finished surface to be flush with
the front of the unit. Total facing thickness
can vary from 1/2" (13mm) to 1-1/4" (32mm)
thick.
NOTE: See next page for important
Barcelona™ Series framing note.
Framing Dimensions
A
B
C
D
36-1/4" 37-1/4" 17-3/8" 46-1/2"*
921mm 946mm 441mm 1181mm*
* 'D' is Minimum height to combustible materials
including the Minimum 2-1/2" (64mm) Top
clearance to the Horizontal Vent.
3) For exterior walls, insulate the enclosure to
the same degree as the rest of the house,
apply vapour barrier and drywall, as per
local installation codes. (Do not insulate
the fireplace itself.)
Install Side Nailing Strips, Top Facing
Support, and Top Standoffs before unit is
slipped into position. See "Unit Assembly
Prior to Installation" section for assembly
details.
Note: 40-1/2" (1029mm) is the minimum
height for both flex termination or
Simpson Dura-Vent venting.
Note: The unit does not have to be completely
enclosed in a chase. The clearance on
top of the unit is 0" to the standoffs so
combustible building materials can
be laid directly on top of the standoffs.
You must maintain clearance from
the vent to combustible materials for
flex, see Vent Clearances.
5) Use steel studs for framing where the
1-1/2" (38mm) clearance from the vent to
combustible material cannot be maintained,
e.g. front top header.
4) The top of the unit must not be closer than
32" (813mm) to the ceiling.
2) Frame in the enclosure for the unit with
framing material. The framed opening is
37-1/4" high x 36-1/4" wide x 17-3/8" deep
(946mm high x 921mm wide x 441mm deep).
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
17
INSTALLATION
TRIPOLI ARCH DOOR FRAMING NOTE
When installing the optional Tripoli Arch Door, a non-combustible material 12" (305mm) above the unit and 6" (153mm) on each side must be used. See
diagram 2. For complete framing dimensions - see instructions in this manual.
The Tripoli Arch Door also requires steel stud framing above and on each side of the unit, see diagram 2.
Min. 12"
(305mm)
Front Framing Dimensions using the
Regency Tripoli Screen Door Option
Non - Combustible
Material
P36
36-1/4"
(921mm)
P36D
376-1/4"
(946mm)
36-1/4"
(921mm)
Min. 6"
(153mm)
Steel
Stud
27-1/2”
(699mm)
30 -7/8”
(784mm)
Steel
Stud
Min. 6"
(153mm)
Diagram 1
18
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
UNIT ASSEMBLY
PRIOR TO
INSTALLATION
The Top Facing Support, the Side Nailing Strips
and the 2 Top Standoffs must be correctly
positioned and attached to the top before unit
is slipped into position.
Top Standoff Assembly
Top Facing Support &
Side Nailing Strips
"C" Screw Position:
For a facing material depth of 1-1/4" (32mm),
the top facing support must be reversed.
Determine the total thickness of facing material
(e.g. drywall plus ceramic tiles) to allow the
finished surface to be flush with the front of the
unit. Total facing thickness can vary from 1/2"
(13mm) to 1-1/4" (32mm) thick.
The Top Facing Support can be mounted in 3
different positions depending on the thickness
of the facing material.
The top standoffs are shipped in a flat position
and must be folded into shape and attached.
1) Remove the standoffs from the fireplace top.
2) Take each standoff and bend into the correct
shape. Bend up at the bend lines until the
screw holes in the standoff and the prepunched screw holes on the fireplace top
line up.
3) Attach the standoff securely to the top with
2 screws per standoff (on opposite corners).
Screw
Position
Facing Material
Depth
A
1/2" / 13mm
B
7/8" / 22mm
C*
1-1/4" / 32mm
2) Fold out the two nailing strips on each side.
* For "C" screw position the top facing
support is reversed.
1) Mount Top Facing Support using the 3
supplied screws into the three pre-punched
screw holes on the top front of the unit. Use
hole positions A, B, or C depending on your
facing depth.
Side
Nailing Strips
VENTING
INTRODUCTION
The P36D-1 uses the "balanced flue"
technology Co-Axial system. The inner liner
vents products of combustion to the outside while
the outer liner draws outside combustion air into
the combustion chamber thereby eliminating the
need to use heated room air for combustion and
losing warm room air up the chimney.
Note:
These flue pipes must not be
connected to any other appliance.
The gas appliance and vent system must be
vented directly to the outside of the building,
and never be attached to a chimney serving a
separate solid fuel or gas burning appliance.
Each direct vent gas appliance must use it's own
separate vent system. Common vent systems
are prohibited.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
19
INSTALLATION
EXTERIOR VENT TERMINATION LOCATIONS
Minimum Clearance Requirements
Canada1
USA2
A
Clearance above grade, veranda, porch, deck, or balcony
12"(30cm)
12"(30cm)
B
Clearance to window or door that may be opened
12"(30cm)
9" (23cm)
C
Clearance to permanently closed window
*
*
D
Vertical clearance to ventilated soffit located above the terminal within a horizontal distance of 2 feet (61cm)
from the center line of the terminal (check with the local code)
18"(46cm)
18"(46cm)
E
Clearance to unventilated soffit
15"(38cm)
15"(38cm)
F
Clearance to outside corner: with AstroCap Termination Cap.
6"(15cm)
6"(15cm)
14"(36cm)
14"(36cm)
6"(15cm)
6"(15cm)
Clearance to outside corner: with all other approved Termination Caps.
G
Clearance to inside corner: with AstroCap Termination Cap
Clearance to inside corner: with all other approved Termination Caps.
12"(30cm)
a
12"(30cm)
H
Clearance to each side of center line extended above meter/regulator assembly
36"(90cm)
J
Clearance to service regulator vent outlet
36"(90cm)
K
Clearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance
12"(30cm)
9" (23cm)
L
Clearance to a mechanical air supply inlet
#3' (91cm) above if within 10' (3m) horizontally.
72"(1.8m)
36"(90cm)b
M
Clearance above paved sidewalk or a paved driveway located on public property
84"(2.1m)┼
*
Clearance under veranda, porch, deck, or balcony
12"(30cm)‡
*
N
*
*
1
In accordance with current CSA B149.1, Natural Gas and Propane Installation Code
2
In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code
┼
A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.
‡ Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor.
*a Clearance in accordance with local installation codes and the requirements of the gas supplier
3 feet (91cm) within a height of 15 feet (4.5m) above the meter / regulator assembly
b 3 feet (91cm) above - if within 10 feet (3m) horizontally
20
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
VENTING
DIRECT VENT SYSTEM (FLEX)
HORIZONTAL TERMINATIONS ONLY
These venting systems, in combination with the P36D-1 Direct Vent Gas Fireplace, have been tested and listed as a direct vent heater system by
Warnock Hersey. The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram in the "Exterior Vent
Termination Locations" section.
FPI Direct Vent (Flex) System Termination Kit (Part # 946-515) includes all the parts needed to install the P36 with a maximum run of 4 feet.
1)
6-7/8" dia. flexible liner (4 ft. length)
2)
4" dia. flexible liner (4 ft. length)
3)
spring spacers (4)
4)
thimble (2)
5)
AstroCap termination cap (1)
6)
screws (12)
7)
tube of Mill Pac (1)
8)
9)
plated screws (8)
screws #8 x 1-1/2" Drill Point, Stainless
Steel (4)
If longer runs are needed, the FPI Direct
Vent system (Flex) # 946-516 includes all
the parts needed to install the P36 with a
maximum 10' run.
1)
6-7/8" dia. flexible liner (10 ft. length)
2)
4" dia. flexible liner (10 ft. length)
3)
spring spacers (7)
4)
thimble (2)
5)
AstroCap termination cap (1)
6)
screws (12)
7)
tube of Mill Pac (1)
8)
plated screws (8)
9)
screws #8 x 1-1/2" Drill Point, Stainless
Steel (4)
Notes:
1) Liner sections should be continuous without any joints or seams.
2) Only Flex pipe purchased from FPI may be used for Flex installations.
3) If you are installing the P36 into a FPI Cabinet Mantel Kit, use the minimum horizontal vent height (centre-line of 40-1/2"). Remember
to include the mantel base (3" in height) in your calculations and to maintain the 2" clearance to the underside of the mantel top.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
21
INSTALLATION
4” X 6-5/8” RIGID PIPE CROSS REFERENCE CHART
Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI.
Description
Simpson
Selkirk
Direct Vent Pro®
Direct Temp™
American Metal
Products®
Metal-Fab™
Security
ICC Excel
Sure Seal
Secure- Vent®
Direct
Amerivent Direct
22
6” Pipe Length-Galvanized
46DVA-06
4DT-6
N/A
4D6
SV4L6
TC-4DL6
6” Pipe Length-Black
46DVA-06B
4DT-6B
N/A
4D6B
SV4LB6
TC-4DL6B
7” Pipe Length-Galvanized
N/A
N/A
4D7
N/A
N/A
N/A
7” Pipe Length-Black
N/A
N/A
4D7B
N/A
N/A
N/A
9” Pipe Length-Galvanized
46DVA-09
4DT-9
N/A
N/A
N/A
N/A
9” Pipe Length-Black
46DVA-09B
4DT-9B
N/A
N/A
N/A
N/A
12” Pipe Length-Galvanized
46DVA-12
4DT-12
4D12
4D12
SV4L12
TC-4DL1
12” Pipe Length-Black
46DVA-12B
4DT-12B
4D12B
4D12B
SV4LB12
TC-4DL1B
18” Pipe Length-Galvanized
46DVA-18
4DT-18
4D18
4D18
SV4LA
TC-4DL18
18” Pipe Length-Black
46DVA-18B
4DT-18B
4D18B
4D18B
SV4LA
TC-4DL18B
24” Pipe Length-Galvanized
46DVA-24
4DT-24
4D24
4D24
SV4L24
TC-4DL2
24” Pipe Length-Black
46DVA-24B
4DT-24B
4D24B
4D24B
SV4LB24
TC-4DL2B
36” Pipe Length-Galvanized
46DVA-36
4DT-36
4D36
4D36
SV4L36
TC-4DL3
36” Pipe Length-Black
46DVA-36B
4DT-36B
4D36B
4D36B
SV4LB36
TC-4DL3B
48” Pipe Length-Galvanized
46DVA-48
4DT-48
4D48
4D48
SV4L48
TC-4DL4
48” Pipe Length-Black
46DVA-48B
4DT-48B
4D48B
4D48B
SV4LB48
TC-4DL4B
60” Pipe Length-Galvanized
46DVA-60
4DT-60
N/A
N/A
N/A
N/A
60” Pipe Length-Black
46DVA-60B
4DT-60B
N/A
N/A
N/A
N/A
Adjustable Length 3”-10”-Galvanized
N/A
N/A
N/A
4DAL
N/A
TC-4DLT
Adjustable Length 3”-10”-Black
N/A
N/A
N/A
4DALB
N/A
TC-4DLTB
Adjustable Length 7”-Galvanized
N/A
N/A
4D7A
N/A
N/A
N/A
Adjustable Length 7”-Black
N/A
N/A
4D7AB
N/A
N/A
N/A
Extension Pipe 8-1/2”-Galvanized
46DVA-08A
N/A
N/A
N/A
N/A
N/A
Extension Pipe 8-1/2”-Black
46DVA-08AB
N/A
N/A
N/A
N/A
N/A
Adjustable Length 12”-Galvanized
N/A
N/A
4D12A
N/A
SV4LA12
N/A
Adjustable Length 12”-Black
N/A
N/A
4D12A
N/A
SV4LBA12
N/A
Extension Pipe 16”-Galvanized
46DVA-16A
N/A
N/A
N/A
N/A
N/A
Extension Pipe 16”-Black
46DVA-16AB
N/A
N/A
N/A
N/A
N/A
45º Elbow-Galvanized
46DVA-E45
4DT-EL45
4D45L
N/A
N/A
TE-4DE45
45º Elbow-Black
46DVA-E45B
4DT-EL45B
4DT-EL45B
N/A
N/A
TE-4DE45B
45º Elbow Swivel-Galvanized
See 46DVA-E45
N/A
N/A
4D45L
SV4E45
N/A
45º Elbow Swivel-Black
See 46DVA-E45B
N/A
N/A
4D45LB
SV4EB45
N/A
90º Elbow-Galvanized
46DVA-E90
4DT-EL90S
4DT-EL90S
N/A
N/A
TE-4DE90
90º Elbow-Black
46DVA-E90B
4DT-EL90SB
4DT-EL90SB
N/A
SV4EBR90-1
TE-4DE90B
90º Elbow, Swivel-Galvanized
See 46DVA-E90
N/A
N/A
4D90L
SV4E90-1
N/A
90º Elbow, Swivel-Black
See 46DVA-E90B
N/A
N/A
4D90LB
SV4EB90-1
N/A
90º Starter Elbow, Swivel-Galvanized
N/A
N/A
N/A
4D90A
N/A
N/A
Adaptor*
N/A
N/A
N/A
4D90L
N/A
N/A
Ceiling Support
N/A
4DT-CS
4DFSP
4DSP
SV4SD
TE-4DE45
Cathedral Support Box
46DVA-CS
4DT-CSS
4DRSB
4DRS
SV4CSB
TE-4DE45B
Wall Support/Band
46DVA-WS
4DT-WS/B
4DWS
4DWS
SV4BM
N/A
Offset Support
46DVA-ES (N/A - FPI)
4DT-OS
N/A
N/A
SV4SU
N/A
Wall Thimble-Black
46DVA-WT
4DT-WT
4DWT
4DWT
SV4RSM
TE-4DE90
Wall Thimble Support/Ceiling Support
46DVA-DC
N/A
N/A
N/A
SV4PF
TE-4DE90B
Firestop Spacer
46DVA-FS
4DT-FS
4DFSP
4DFS
SV4BF
N/A
Trim Plate-Black
N/A
4DT-TP
4DFPB
4DCP
SV4LA
N/A
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
Description
Simpson
Selkirk
Direct Vent Pro®
Direct Temp™
American Metal
Products®
Metal-Fab™
Security
ICC Excel
Sure Seal
Secure- Vent®
Direct
Amerivent Direct
Attic Insulation Shield 12”
46DVA-IS N/A@ FPI
N/A
4DAIS12
N/A
SV4RSA
N/A
Attic Insulation Shield - Cold Climates 36”
N/A
N/A
4DAIS12
N/A
N/A
TM-4AS
Basic Horizontal Termination Kit (A)
Disc.
4DT-HKA
4DHTK2
4DHTKA
SV-SHK
N/A
Horizontal Termination Kit (B)
46DVA-KHA
4DT-HKB
4DHTK1
4DHTKB
SV-HK
N/A
4DT-VKC
4DHTK
4DHTK
SV-FK
N/A
(Changed Components)
Vertical Termination Kit
Disc.
High Wind Vertical Cap
46DVA-VCH
N/A
N/A
N/A
N/A
TM-4VT
High Wind Horizontal Cap
46DVA-HC
N/A
N/A
N/A
N/A
TM-4DHT
TM-4HT
Horizontal Square Termination Cap
See 46DVA-HC
4DT-HHC
4DHC
4DHT
SV4CHC-1
Vertical Termination Cap
46DVA-VC
4DT-HVC
4DVC
4DVT
SV4CGV-1
TM-4VT
Storm Collar
46DVA-08A
4DT-SC
4DSC
4DSC
SV4FC
TM-SC
Adjustable Flashing 0/12-6/12
46DVA-F6
4DT-ST14
4D12S
4DST14
SV4STC14
TF-4FA
Adjustable Flashing 6/12-12/12
46DVA-FLA
4DT-ST36
4D36S
4DST36
SV4STC36
TF-4FB
Vinyl Siding Standoff
46DVA-VSS
4DT-VS
N/A
4DVS
SV4VS
TM-VSS
Vinyl Siding Shield Plate
N/A
4DT-VSP
N/A
N/A
SV4VS
N/A
Snorkel Termination 14”
46DVA-SNKL
N/A
N/A
N/A
N/A
TM-4ST14
Snorkel Termination 36”
N/A
N/A
N/A
N/A
N/A
TM-4ST36
Restrictor Disk
N/A
N/A
N/A
N/A
N/A
TM-4DS
Extended Vertical Termination Cap
N/A
N/A
N/A
N/A
N/A
N/A
Chimney Conversion Kit A (USA only)
46DVA-KCA
N/A
N/A
N/A
N/A
TM-4CA6
Chimney Conversion Kit B (USA only)
46DVA-KCB
N/A
N/A
N/A
N/A
TM-4CA7
Chimney Conversion Kit C (USA only)
46DVA-KCC
N/A
N/A
N/A
N/A
TM-4CA8
Chimney Conversion Kit Masonry
(USA only)
46DVA-KMC
N/A
N/A
N/A
N/A
N/A
Wall Firestop
46DVA-WFS
N/A
N/A
N/A
N/A
TM-4TR
Colinear Flex Connectors
46DVA-ADF
N/A
N/A
N/A
N/A
N/A
FPI
946-506/P
Vent Guard (Optional) for AstroCap
946-205
510-994
Rigid Pipe Adaptor (Must use with all rigid piping)
946-208/P
Vinyl Siding Shield for Riser Vent Terminal
Vent Guard (Optional) for Riser Vent Terminal
640-530/P
Riser Vent Terminal
946-523/P
AstroCap Horizontal Cap
946-605
Starter Collar Increaser 4” x 6-5/8” to 5” x 8”
946-206
Vinyl Siding Standoff for AstroCap
Note: When using Metal-Fab Sure Seal Rigid Piping - please note that the Adaptor (4DDA) must be used in conjunction with FPI Rigid Pipe Adaptor (510-994).
Offset Pipe Selection: Use this table to determine offset pipe lengths.
Pipe Length
(L)
4” x 6-5/8” Venting
For specific instructions on venting components - visit the
manufacturers website listed below.
Run (X)
Rise (Y)
0” (0mm)
4-7/8” (124mm)
13-7/8” (340mm)
Simpson Direct Vent Pro: www.duravent.com
6” (152mm)
8” (203mm)
16-1/2” (419mm)
Selkirk Direct-Temp: www.selkirkcorp.com
9” (229mm)
10-1/8” (257mm)
18-5/8” (473mm)
American Metal Products: www.americanmetalproducts.com
12” (305mm)
12-1/4” (311mm)
20-3/4” (527mm)
Metal-Fab Sure Seal: www.mtlfab.com
24” (610mm)
20-5/8” (524mm)
29-1/8” (740mm)
Security Secure Vent: www.securitychimneys.com
36” (914mm)
29” (737mm)
37-1/2” (953mm)
Industrial Chimney Company: www.icc-rsf.com
48” (1219mm)
37-7/16” (951mm)
45-15/16” (1167mm)
Note: Horizontal runs of vent must be level, or have a 1/4” rise for every 1 foot of run towards the termination.
Never allow the vent to run downward - this could cause high temperatures and may present a possible fire hazard.
Regency Fireplace Products . 6988 Venture St. . Delta, BC . Canada . V4G 1H4 . 604-946-5155 . www.regency-fire.com
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
23
INSTALLATION
RIGID PIPE VENTING SYSTEMS
Horizontal or Vertical Terminations
The minimum components required for a basic
horizontal termination are:
1
1
1
1
1
Flat Wall Installation
Wall Thickness (inches)
Vent Length Required (inches)
4" - 5-1/2"
6"
Horizontal Termination Cap
90o Elbow
Rigid Pipe Adaptor
Wall Thimble
Length of pipe to suit wall thickness
(see chart)
Wall thickness is measured from the back standoffs
to the inside mounting surface of termination cap.
For siding other than vinyl furring strips may be used,
instead of the vinyl siding standoff, to create a level
surface to mount the vent terminal. The Terminal
must not be recessed into siding. Measure the wall
thickness including furring strips.
7" - 8-1/2"
9"
10" - 11-1/2"
12"
9" - 14-1/2"
11" - 14-5/8" Adj. Pipe
15" - 23-1/2"
17" - 24" Adj. Pipe
Corner Installation
Wall Thickness (inches)
Vent Length Required (inches)
If a Vinyl Siding Standoff is required (it must be used
with vinyl siding), measure to outside surface of wall
without siding and add 2 inches.
3-1/4" - 6-3/4"
11" - 14-5/8" Adj. Pipe
7-3/4" - 16-1/4"
17" - 24" Adj. Pipe
7-1/4" - 8-3/4"
6" + 12"
9" + 9"
4-1/4" - 5-3/4"
6" + 9"
Vertical
Termination
Cap
Alternate
Horizontal
Termination
Caps
Storm Collar
Vinyl Siding
Standoff (Optional)
Flashing
Horizontal
Termination
Cap
Ceiling Firestop
Wall Thimble
Pipe Length
Adj.Pipe Length
11" - 14-5/8"
90o Elbow
24" Pipe
Length
Rigid Pipe Adaptor
WARNING:
Do not combine venting components from
different venting systems.
However use of the AstroCapTM and FPI Riser
is acceptable with all systems.
This product has been evaluated by Intertek for
using a Rigid Pipe Adaptor in conjunction with
DuraVent Direct Vent, Selkirk Direct-Temp, Ameri
Vent Direct venting and Security Secure Vent
systems. Use of these systems with the Rigid
Pipe Adaptor is deemed acceptable and does not
affect the Intertek WHI listing of components.
The FPI AstroCapTM and FPI Riser Vent terminal are certified for installations using FPI venting systems as well as Simpson Dura-Vent® Direct Vent ,
American Metal Products, Security Secure Vent®, AmeriVent Direct Vent. AstroCapTM is the proprietary trademark of FPI Fireplace Products International
Ltd. Dura-Vent® and Direct Vent are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.
24
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
VENTING ARRANGEMENTS
HORIZONTAL TERMINATION
RIGID PIPE AND FPI DIRECT VENT SYSTEM (FLEX)
(Propane & Natural Gas)
The diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 90o elbow (two 45o elbows equal one 90o
elbow).
Note: Must use optional rigid pipe adaptor (Part # 510-994) when using Rigid Pipe venting systems.
All Rigid Pipe Systems
4" inner diameter
6-5/8" outer diameter
FPI Flex Vent
4" inner diameter
6-7/8" inner diameter
A vent guard should be used
whenever the termination is lower
than the specified minimum or as
per local codes.
Note: FPI Direct Vent Flex System Part #'s
946-515 and 946-516 are only approved
for horizontal terminations.
•
•
•
Maintain clearances to combustibles.
Horizontal vent must be supported every 3 feet.
Firestops are required at each floor level and whenever passing through a wall.
NOTE: If you are installing the P36D-1 into an FPI cabinet Mantel Kit, use the minimum horizontal vent height
(centre-line of 40-1/2"). Remember to include the mantel base (3" in height) in your calculations and to maintain the 2" clearance
from the top with rigid or flex pipe systems to the underside of the mantel top.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
25
INSTALLATION
VENTING ARRANGEMENTS
VERTICAL TERMINATION
RIGID PIPE SYSTEM
(Propane & Natural Gas)
The shaded area in the diagram shows all allowable combinations of straight vertical and offset to vertical terminations, using two 90o elbow, with
rigid pipe vent systems for Propane and Natural Gas.
•
•
•
Vent must be supported at offsets.
Firestops are required at each floor level and whenever passing through a wall.
Maintain clearances to combustibles.
Note: Must use optional rigid pipe adaptor when using rigid vent systems (Part # 510-994).
26
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
The P36D-1 is approved for a 40 ft. straight vertical,
with rigid pipe vent systems for Propane and Natural
Gas, as per the diagram 1.
The shaded area in the diagram 1 shows all
allowable combinations of straight vertical and
offset to vertical terminations with rigid pipe vent
systems for Propane and Natural Gas. Maximum
two 45o elbows allowed.
•
Vent must be supported at offsets
•
Firestops are required at each floor level
and whenever passing through a wall.
•
Maintain clearances to combustibles.
Diagram 1
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
27
INSTALLATION
HORIZONTAL VENTING WITH TWO (2) 90O ELBOWS
H1
H
V
One 90o elbow = Two 45o elbows.
Option
A)
B)
C)
D)
E)
F)
G)
0'
1'
2'
3'
4'
5'
6'
V
Min.
Min.
Min.
Min.
Min.
Min.
Min.
H + H1
2' Max.
3' Max.
4' Max.
5' Max.
6' Max.
7' Max.
8' Max.
With these options,
maximum total pipe length
is 30 feet with minimum
of 6 feet total vertical
and maximum 8 feet total
horizontal.
Please note minimum 1
foot between 90o elbows
is required.
Lengths do not include elbow indicated.
HORIZONTAL VENTING WITH THREE (3) 90O ELBOWS
One 90o elbow = Two 45o elbows.
Option
A)
B)
C)
D)
E)
F)
G)
H)
V
0' Min.
1' Min.
2' Min.
3' Min.
4' Min.
5' Min.
6' Min.
7' Min.
H
1' Max.
2' Max.
2' Max.
2' Max.
3 Max.
4' Max.
5' Max.
6' Max.
V + V1
1' Min.
3' Min.
5' Min.
7' Min.
9' Min.
10' Min.
11' Min.
12' Min.
H + H1
2' Max.
3' Max.
4' Max.
5' Max.
6' Max.
7' Max.
8' Max.
9' Max.
With these options,
max. total pipe length
is 30 feet with min. of
12 feet total vertical
and max. 9 feet total
horizontal.
Please note min. 1
foot between 90 o
elbows is required.
Lengths do not include elbow indicated.
28
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
VERTICAL VENTING WITH TWO (2) 90O ELBOWS
V1
V
H
One 90o elbow = Two 45o elbows.
Option
A)
B)
C)
D)
E)
F)
V
0' Min.
1' Min.
2' Min.
3' Min.
4' Min.
5' Min.
H
2' Max.
4' Max.
5' Max.
6' Max.
7' Max.
8' Max.
V + V1
1' Min.
3' Min.
4' Min.
5' Min.
6' Min.
7' Min.
With these options, max. total
pipe length is 30 feet with min.
of 7 feet total vertical and max.
8 feet total horizontal.
Please note min. 1 foot
between 90 o elbows is
required.
Lengths do not include elbow indicated.
VERTICAL VENTING WITH THREE (3) 90O ELBOWS
V1
H1
o
H
V
o
One 90 elbow = Two 45 elbows.
Option
A)
B)
C)
D)
E)
F)
G)
H)
V
0' Min.
1' Min.
2' Min.
3' Min.
4' Min.
5' Min.
6' Min.
7' Min.
H + H1
2' Max.
2' Max.
3' Max.
4' Max.
5' Max.
6' Max.
7' Max.
8' Max.
V + V1
2' Min.
3' Min.
4' Min.
6' Min.
7' Min.
8' Min.
9' Min.
10' Min.
With these options, max.
total pipe length is 30 feet
with min. of 10 feet total
vertical and max. 8 feet
total horizontal.
Please note min. 1 foot
between 90o elbows is
required.
Lengths do not include elbow indicated.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
29
INSTALLATION
VERTICAL TERMINATION
WITH CO-LINEAR FLEX SYSTEM
THE APPLIANCE MUST NOT BE
CONNECTED TO A CHIMNEY FLUE
SERVING A SEPARATE SOLID FUEL
BURNING APPLIANCE.
Masonry chimneys may take various contours which the flexible liner will accommodate. However,
keep the flexible liner as straight as possible, avoid unnecessary bending.
The Air Intake pipe must be attached to the inlet air collar of the termination cap.
This appliance is designed to be attached to
two 3" (76mm) co-linear aluminium flex running
the full length of the chimney. See the Venting
Arrangements on next page for minimum and
maximum heights.
Co-linear DV
Vertical Termination
Cap # 946-529
Required Parts:
Part #
Description
946-529
Co-linear DV Vertical
Termination Cap
3" Flex - 35 ft.
Co-Axial to Co-Linear Adapter Kit
which contains the following:
Co-linear Flex Adapter
Outer Pipe
Inner Pipe Adapter
Rigid Pipe Adaptor
948-305
946-563
510-994
A maximum
of two certified
joiner kits
may be used
per length.
#948-305 (35 ft)
Flex Liner
Exhaust
Flue
FPI Cabinet and/or Flat Wall Mantles may
be used in these applications ensuring
that clearances to combustibles are
maintained.
Outer
Pipe
with Kit#
946-563
Air Intake
Pipe Length
Rigid Pipe Adapter
# 510-994
30
90 Degree
Elbow
Co-Linear
Flex
Adapter
with Kit#
946-563
Inner Pipe
Adapter
with Kit#
946-563
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
VENTING ARRANGEMENT - VERTICAL TERMINATIONS
CO-LINEAR FLEX SYSTEM
INTO MASONRY FIREPLACES
FOR BOTH RESIDENTIAL & MANUFACTURED HOMES
8' Min.
40-1/2”
2’ max.
30' Max.
Vertical Height (feet)
30
Horizontal Distance (Feet)
The shaded area in the diagrams show the allowable vertical terminations.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
31
INSTALLATION
UNIT INSTALLATION WITH
HORIZONTAL TERMINATION
b) Horizontal runs of vent must be
supported every three feet. Wall straps
are available for this purpose.
Install the vent system according to the
manufacturer's instructions included with
the components.
5) Mark the wall for a 10" x 10" square hole. The
center of the square hole should line up with
the centerline of the horizontal pipe. Cut and
frame the 10 inch square hole in the exterior
wall where the vent will be terminated. If the
wall being penetrated is constructed of noncombustible material, i.e. masonry block or
concrete, a 7"(178mm) dia. (7-1/2"(191mm)
dia. for flex) hole is acceptable.
1) Set the unit in its desired location. Check
to determine if wall studs or roof rafters
are in the way when the venting system is
attached. If this is the case, you may want
to adjust the location of the unit. Rough in
the gas preferably on the right side of the
unit and the electrical (junction block is on
the left side) on the left.
2) Direct Vent pipe and fittings are designed with
special twist-lock connections to connect the
venting system to the appliance flue outlet. A
twist-lock appliance adaptor is an available
option that must be used in conjunction
with the Simpson Dura-Vent Direct Vent
system.
3) Put a bead of silicone inside the outer section
of the adapter and a bead of Mill Pac on
the inner collar. Slip the adapter over the
existing inner and outer flue collar and fasten
to the outer collar only with the 3 supplied
screws (drilling pilot holes will make this
easier). Level the fireplace and fasten it to
the framing using nails or screws through
the nailing strips.
4) Assemble the desired combination of pipe
and elbows to the appliance adaptor and
twist-lock for a solid connection.
Notes:
a) Twist-lock procedure: Four indentations,
located on the female ends of pipes and
fittings, are designed to slide straight
onto the male ends of adjacent pipes
and fittings, by orienting the four pipe
indentations so they match and slide
in to the four entry slots on the male
ends, Diagram 1. Push the pipe sections
completely together, then twist-lock
one section clockwise approximately
one-quarter turn, until the two sections
are fully locked. The female locking lugs
will not be visible from the outside, on
the Black Pipe or fittings. They may be
located by examining the inside of the
female ends.
Diagram 1
NOTE: For best results and optimum
performance with each approved venting
system, it is highly recommended to apply
“Mill-Pac” sealant (supplied) to every inner pipe connection. Failure to do so may
result in drafting or performance issues not
covered under warranty. Silicone (red RTV)
is optional.
32
Note: Riser Vent
is only for use
in above grade
terminations.
Note: With
D u r a - Ve n t ,
the minimum
height is
achieved by
installing
a 90 o elbow
directly to
the rigid pipe
adaptor.
Diagram 3a
*Diagrams 3 & 4: As specified in CGA B149
Installation Code. Local codes or regulations
may require different clearances.
Below Grade Installation
Diagram 2
Notes:
a) The horizontal run of vent must be level,
or have a 1/4 inch rise for every 1 foot
of run towards the termination. Never
allow the vent to run downward. This
could cause high temperatures and may
present the possibility of a fire.
If the Snorkel Termination must be installed
below grade, i.e. basement application, proper
drainage must be provided to prevent water
from entering the Snorkel Termination. Refer
to Diagram 4. Do not attempt to enclose the
Snorkel within the wall, or any other type of
enclosure.
b) The location of the horizontal vent
termination on an exterior wall must meet
all local and national building codes, and
must not be blocked or obstructed. For
External Vent Terminal Locations, see
Exterior Vent Termination Location.
c) Snorkel Terminations:
For installations requiring a vertical
rise on the exterior of the building, 14inch and 36-inch tall
Snorkel Terminations
are available, as well
as the standard Riser
Vent. Follow
the same installation procedures as
used for
standard
Horizont a l Te r mination.
NEVER
install the
snorkel
upside
down.
Diagram 4
NOTE: For Snorkel terminations in ABOVE
grade installations, follow national
or local code requirements.
6) The arrow on the vent cap should
be pointing up. Insure that the 1-1/2"
clearances to combustible materials
are maintained (Diagram 4). Install the
termination cap.
Diagram 3
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
UNIT INSTALLATION WITH
VERTICAL TERMINATION
1) Maintain the 1-1/4" clearances
(air spaces) to combustibles
when passing through ceilings,
walls, roofs, enclosures,
attic rafter, or other nearby
combustible surfaces. Do not
pack air spaces with insulation.
Check for the maximum
vertical rise of the venting
system and the maximum
horizontal offset limitations.
Diagram 5
The four wood screws provided should
be replaced with appropriate fasteners for
stucco, brick, concrete, or other types of
sidings.
Note: If installing termination on a siding
covered wall, a vinyl siding standoff
or furring strips must be used to
ensure that the termination is not
recessed into the siding.
7) Before connecting the horizontal run of vent
pipe to the vent termination, slide the Wall
Thimble over the vent pipe.
8) Slide the appliance and vent assembly
towards the wall carefully inserting the
vent pipe into the vent cap assembly. It is
important that the vent pipe extends into
the vent cap sufficient distance so as to
result in a minimum pipe overlap of 1-1/4
inches. Secure the connection between the
vent pipe and the vent cap by attaching the
two sheet metal strips extending from the
vent cap assembly into the outer wall of the
vent pipe. Use the two sheet metal screws
provided to connect the strips to the pipe
section. See Diagram 6.
2) Set the gas appliance in
its desired location. Drop
a plumb bob down from
the ceiling to the position
of the appliance flue exit,
Diagram 1
and mark the location
where the vent will penetrate the ceiling. Drill
a small hole at his point. Next, drop a plumb
bob from the roof to the hole previously
drilled in the ceiling, and mark the spot where
the vent will penetrate the roof. Determine if
ceiling joists, roof rafters or other framing will
obstruct the venting system.
You may wish to relocate the
appliance or to
offset, as shown
in Diagram 2
to avoid cutting
load bearing
members.
4) Assemble the desired lengths of pipe and
elbows. Ensure that all pipes and elbow
connections are in the fully twist-locked
position and sealed.
5) Cut a hole in the roof centered on the small
drilled hole placed in the roof in Step 2. The
hole should be of sufficient size to meet
the minimum requirements for clearance
to combustibles of 1-1/2". Slip the flashing
under the shingles (shingles should overlap
half the flashing) as per Diagram 4.
Diagram 4: The upper half of the flashing is
installed under the roofing material and not
nailed down until the chimney is installed.
This allows for small adjustments.
6) Continue to assemble pipe lengths.
Note: If an offset is necessary in the attic
to avoid obstructions, it is important
to support the vent pipe every 3 feet,
to avoid excessive stress on the
elbows, and possible separation.
Wall straps are available for this
purpose (Diagram 2).
Galvanized pipe is desirable above the roofline
due to its higher corrosion resistance. Continue
to add pipe sections through the flashing until
the height of the vent cap meets the minimum
height requirements specified in Diagram 5 or
local codes. Note that for steep roof pitches,
Diagram 2
NOTE: For best results and optimum
performance with each approved venting
system, it is highly recommended to apply
“Mill-Pac” sealant (supplied) to every inner
pipe connection. Failure to do so may result
in drafting or performance issues not covered
under warranty. Silicone (red RTV) is optional.
Diagram 5
Roof Pitch
3) A Firestop spacer must be installed in the
floor or ceiling of every level. To install the
Firestop spacer in a flat ceiling or wall,
cut a 10 inch square hole. Frame the hole
as shown in Diagram 3 and install the
firestop.
Diagram 6
9) Install wall thimble in
the center of the 10"
square and attach
with wood screws
(Diagram 7).
Diagram 3
Diagram 7
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
flat to 7/12
over 7/12 to 8/12
over 8/12 to 9/12
over 9/12 to 10/12
over 10/12 to 11/12
over 11/12 to 12/12
over 12/12 to 14/12
over 14/12 to 16/12
over 16/12 to 18/12
over 18/12 to 20/12
over 20/12 to 21/12
Minimum Vent Height
Feet
Meters
2
0.61
2
0.61
2
0.61
2.5
0.76
3.25
0.99
4
1.22
5
1.52
6
1.83
7
2.13
7.5
2.29
8
2.44
33
INSTALLATION
the vertical height must be increased. A poor
draft, or down drafting can result from high
wind conditions near big trees or adjoining
roof lines, in these cases, increasing the vent
height may solve the problem.
7) Ensure vent is vertical and secure the base
of the flashing to the roof with roofing rails,
slide storm collar over the pipe section and
seal with a mastic.
4) Separate the 2 halves of the wall thimble and
securely fasten the one with the tabs to the
outside wall making sure that the tabs are
on top and bottom. Fasten the other thimble
half to the inside wall. The thimble halves
slip inside each other and can be adjusted
for 2 x 4 or 2 x 6 walls. The liners must slip
over the collars a minimum of 1-3/8".
N o t e : To m a k e
the installation
more aesthetically
pleasing,
we
recommend framing
out a square to
mount the terminal
to.
8) Install the vertical termination cap by twistlocking it.
Note: Any closets or storage spaces, which
the vent passes through must be
enclosed.
Offset Chart
Note: If installing termination on a siding
covered wall, furring strips must be
used to ensure that the termination
is not recessed into the siding.
2) Level the fireplace and fasten it to the framing
using nails or screws through the nailing
strips.
3) Assemble the vent assembly by applying
Mill Pac to the 4"(100mm) inner collar of the
termination and slipping the 4"(100mm) liner
over it at least 1-3/8" (35mm). Fasten with
the 3 screws (drilling pilot holes will make this
easier). Apply Mill Pac or high temperature
silicone to the 6-7/8"(175mm) flex pipe and
slip it over the 6-7/8" outer collar of the vent
terminal at least 1-3/8"(35mm) and fasten
with the 3 screws.
NOTE:
DIRECT VENT
SYSTEM (FLEX)
INSTALLATION
PROCEDURES
Horizontal sections must be
supported at intervals not exceeding
3 feet (0.9 meter). (Flame picture and
performance will be affected by sags
in the liner).
5) Slip the assembled liner and termination
assembly through the thimble making sure
the termination cap faces up (there are
markings on the cap that show which way
is up). This will position the termination cap
with proper down slope for draining water.
Fasten the cap to the outer wall with the 4
supplied screws.
6) Pull the centre 4"(100mm) liner and outer
6-7/8"(175mm) liner out enough to slip over
the flue collars of the fireplace. (You may
wish to cut the liner shorter to make it more
workable.) Do not bend liner more than
90o.
7) Apply Mill Pac over the fireplace inner collar
and slip the 4"(100mm) liner down over it
and attach with 3 supplied screws.
8) Do the same with the 6-7/8"(175mm) liner.
9) Apply a bead of silicone between the thimble
and termination and around the outer edge
of the terminal at the wall in order to keep
the water out.
IMPORTANT: Do not locate termination
hood where excessive snow or ice
buildup may occur. Be sure to check vent
termination area after snow falls, and clear
to prevent accidental blockage of venting
system. When using snow blowers, make
sure snow is not directed towards vent
termination area.
1) Locate the unit in the framing, rough in the
gas (preferably on the right side of the unit)
and the electrical (Junction block is on the
left side) on the left. Locate the centerline of
the termination and mark wall accordingly.
Cut a 10"(254mm) hole in the wall (inside
dimension).
Note: A 1-1/2"(38mm) clearance around
the liner must be maintained except
that only a 1" (25mm) clearance is
needed at the termination end. We
recommend framing a 10"(254mm)
x 10"(254mm) (inside dimensions)
hole to give structural rigidity for
mounting the termination.
34
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
P36D-NG1 SYSTEM DATA
For 0 to 4500 feet altitude
Burner Inlet Orifice Sizes:
#37
Max. Input Rating
Min. Input Rating
30,000 Btu/h
15,500 Btu/h
Supply Pressure
min.5.0" w.c.
Manifold Pressure
(High)
3.8"+/- 0.2"w.c.
Electrical: 120 V A.C. System.
Circulation Fan: variable speed 130 CFM.
Log Set: Ceramic fibre, 7 per set.
Vent System: Simpson Dura-Vent Direct
Vent System or FPI Direct
Vent System (Flex)
P36D-LP1 SYSTEM DATA
Conversion Kit # 514-969
For 0 to 4500 feet altitude
Burner Inlet Orifice Sizes:
#52
Max. Input Rating
30,000 Btu/h
Min. Input Rating
Supply Pressure
15,000 Btu/h
min.12.0" w.c.
always best to consult with your local authorities
and the CAN/CGA B149 installation code.
For USA installations follow local codes and/
or the current National Fuel Gas Code, ANSI
Z223.1.
When using copper or flex connectors use only
approved fittings. Always provide a union so
that gas lines can be easily disconnected for
servicing. Flare nuts for copper lines and flex
connectors are usually considered to meet this
requirement.
Important: Always check for gas leaks with
a soap and water solution or gas leak detector. Do not use open flame for leak testing.
PILOT ADJUSTMENT
Periodically check the pilot flames. Correct
flame pattern has three strong blue flames:
1 flowing around the thermopile, 1 around
the thermocouple and 1 flowing across the
burner (it does not have to be touching the
burner).
Note: If you have an incorrect flame pattern,
contact your FPI dealer for further
instructions.
The manifold pressure is controlled by a regulator
built into the gas control, and should be checked
at the pressure test point.
Note: To properly check gas pressure, both
inlet and manifold pressures should
be checked using the valve pressure
ports on the valve.
1) Make sure the valve is in the "OFF"
position.
2) Loosen the "IN" and/or "OUT" pressure
tap(s), turning counterclockwise with a
1/8" wide flat screwdriver.
3) Attach manometer to "IN" and/or "OUT"
pressure tap(s) using a 5/16" ID hose.
4) Light the pilot and turn the valve to "ON"
position.
5) The pressure check should be carried out
with the unit burning and the setting should
be within the limits specified on the safety
label.
6) When finished reading manometer, turn
off the gas valve, disconnect the hose and
tighten the screw (clockwise) with a 1/8" flat
screwdriver. Note: Screw should be snug,
but do not over tighten.
Manifold Pressure
(High)
11"+/- 0.2" w.c.
S.I.T. VALVE
DESCRIPTION
Electrical: 120 V A.C. System.
Circulation Fan: variable speed 130 CFM.
Log Set: Ceramic fibre, 7 per set.
Vent System: Simpson Dura-Vent Direct
Vent System
HIGH ELEVATION
Incorrect flame pattern will have small,
probably yellow flames, not coming into
proper contact with the rear burner or
thermopile or thermocouple.
This unit is approved in Canada for altitude 0
to 4500 ft. (CAN1 2.17-M91) with the orifice
supplied.
1)
2)
3)
4)
5)
6)
7)
8)
9)
Gas on/off knob
Manual high/low adjustment
Pilot Adjustment
Thermocouple Connection - option
Outlet Pressure Tap
Inlet Pressure Tap
Pilot Outlet
Main Gas Outlet
Alternative TC Connection
Point
GAS LINE
INSTALLATION
The gas line can be brought through either the
right or the left side of the appliance. The gas
valve is situated on the right hand side of the
unit and the gas inlet is on the right hand side
of the valve.
Note: If the gas line is being installed from
the left side, be sure to leave room to
accommodate servicing of the fan.
The gas line connection may be made of rigid
pipe, copper pipe or an approved flex connector.
(If you are using rigid pipe, ensure that the valve
can be removed for servicing.) Since some
municipalities have additional local codes it is
GAS PIPE PRESSURE
TESTING
The appliance must be isolated from the gas
supply piping system by closing its individual
manual shut-off valve during any pressure
testing of the gas supply piping system at
test pressures equal to or less than 1/2 psig.
(3.45 kPa). Disconnect piping from valve at
pressures over 1/2 psig.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
35
INSTALLATION
CONVERSION KIT# 514-969 FROM NG TO LP
for P36D-1 / P36-4 / U32-4 / U37-1 using SIT 820 NOVA Gas Valve
THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER
IF IN DOUBT DO NOT DO THIS CONVERSION !!
Each Kit contains one LPG
Conversion Kit and one DC
Sparker Kit.
Conversion Kit Contains:
Qty.
Part #
Description
1
904-390
Burner Orifice #52
1
904-529
5/32" Allen Key
1
918-590
Decal "Converted
to LPG"
1
908-528
Red "LPG" label
1
910-037
LPG Injector
(Pilot Orifice)
1
918-481
Instruction Sheet
DC Sparker Kit Contains:
Qty.
Part #
Description
1
820-475
Bracket DC Sparker
1
820-476
Bracket DC Sparker
1
904-153
Washer #8 External Star
1
904-330
Nut 8-32 Hex
2
904-531
Bushing Split Plastic
0.500 in.
1
904-543
Screw 8-32 x 3/4 Pan
Head
2
904-553
Screw #8 x 1/2 Type "B",
Black Oxide
1
910-073
Spark Generator Battery
Holder
1
910-074
Spark Generator Switch
C/W Wire
1
910-078
Battery Size AA
Energizer En91
2
910-199
Clip Wire Holder
1
910-903
Wire Fan To Power Cord
Ground 30 in.
904-781
Velcro Hook, Black
904-782
Velcro Hook, Black
For P36D-1 / P36-4 Only:
5)
6)
Pull off the pilot cap to expose the pilot
orifice.
7)
Unscrew the pilot orifice with the allen
key; then replace with the LPG pilot
orifice and the pilot cap, provided in the
kit.
8)
Remove burner orifice with a 1/2"
wrench. Use another wrench to hold on
to the elbow behind the orifice. Discard
orifice.
Remove the 2 screws holding the Burner
Assembly to the firebox base. Push the
Burner Assembly to the left and lift out.
Remove the 2 screws, push Burner Assembly
to the left and lift out.
For U32-5 Only:
5a) Remove the grate by removing the
screws on each side of the grate.
Remove the 2 screws
holding the grate in position.
5b) Remove the Burner Tray by removing
the screws on each side of the tray.
Push the tray to the left and lift up.
Installation of LPG
Conversion Kit:
Burner Orifice
1)
Shut off the gas supply.
2)
Remove the louvers (and bay door if it is
installed).
3)
Open the flush door and remove the
door.
4)
Remove the logs and embers (if already
installed).
36
Remove the 2 screws,
push Burner Tray to the left, and lift off.
IMPORTANT
Before re-installation of the burner (once
the LP conversion is complete), the air
deflector must be installed. See step 18a.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
9)
Reinstall new burner orifice LPG
stamped #52 and tighten.
10) Turn control knob to the “OFF” position.
16) Verify that if the conversion is from
NG to LPG, the screw must be reassembled with the red o-ring visible
(Fig. 5).
Red o-ring visible
Installation of the DC Sparker:
21) Locate the Piezo Ignitor situated at the
side of valve.
LPG Configuration
Piezo
Ignitor
11) Remove the black
protection cap by hand
from the hi-low knob
(Fig.1).
Fig.5
Fig. 1
17) Re-assemble the black protection
cap (Fig. 6).
12) Insert a 5/32” or 4mm
Allen wrench into the
hexagonal key-way
of the screw (Fig.
2), rotate it counterclockwise until it is free
and extract it.
Ignitor
Wire
Fig.2
Fig. 6
13) Check that the screw is clean and if
necessary remove dirt.
Piezo
Ignitor
18) Reverse steps 6 - 1.
For U32-5 Only:
18a) Install the air deflector to the back wall of
the firebox using 2 screws.
14) Flip the screw (Fig. 3).
22) Remove the Piezo Ignitor by unscrewing
the nut at the back of the mounting
bracket.
23) Disconnect the ignitor wire from the
Piezo Ignitor and connect it to the DC
Sparker.
DC
Sparker
Fig.3
Ignitor
Wire
15) Using the Allen wrench
as shown in Fig.4, rotate
the screw clockwise until
snug, do not overtighten.
Air Deflector
Fig.4
WARNING!
Do not over tighten the screw.
Recommended to
grip the wrench by the short side.
24) Connect the DC spark generator wires
to the SIT Valve with the screw, which is
provided in the kit.
WARNING!
Also check that the pilot and main
burner injectors are appropriate for
the gas type.
19) Attach the label "This unit has been
converted to LPG" near or on top of the
serial # decal.
20) Replace yellow "NG" label with red
"LPG" label.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
37
INSTALLATION
25) Locate the ground lug.
28) Install the 1/2" bushing to the heat
shield.
For P36D-1 / P36-4 Only:
32) Mount the heat shield to the DC Sparker.
Secure into place with the velcro, which is
provided in the kit.
25a) By the receptical box, left of the unit.
29) Plug the DC spark generator wires to the
DC Sparker.
33) Find a location which is not too hot and
is easy to reach for changing the battery.
Note: It should be kept away from the
chain.
Chain
For U32-5 Only:
25b) Located on the left side of the unit.
34) Tie up the loose wires with the wire clip.
30) Connect the ground wire to the DC Sparker
mounting bracket.
26) Connect one end of the supplied green
ground wire to the lug with the nut and
washer from the kit.
Ground
wire from
kit
35) Check for gas leaks.
36) Check inlet and outlet pressures.
27) Run the other end of the ground wire
and DC spark generator wires through
the bushing on the heat shield.
Heat Shield
37) Check operation of flame control.
31) Install the supplied battery into the DC
Sparker Box by opening the battery
compartment.
Battery
Compartment
38
38) Check for proper flame appearance and
glow on logs.
NOTE:
The battery in the DC Sparker
Box will need to be replaced annually.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
OPTIONAL
BRICK PANELS
1) Undo the bottom 2 door latches and open and remove glass door.
Remove logs.
4) Install the 2 brick retaining clips, one on each side.
Note: The logs must not be in the unit.
2) Insert the back brick panel first by carefully slipping it between the
back wall of the firebox and the rear log bracket.
3) Put the side panels in next. Slide them in from the front and push
them flat up against the wall. Be very careful not to scratch them on
the firebox hardware.
Note:
If the bottom brick panel must be removed: Remove the Rear
Log Stand, then remove the Burner Tray.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
39
INSTALLATION
Read the instructions below carefully and refer to the
diagrams. If logs are broken do not use the unit until
they are replaced. Broken logs can interfere with the
pilot operation.
3)
Place the Log 02-75 on the rear log support pins with the
flat side to the back.
The gas log kit (Part #780-930) contains the following
pieces:
a)
b)
c)
d)
e)
f)
g)
h)
i)
j)
02-75
02-55
02-50
02-53
02-51
02-54
02-52
902-156
902-179
946-669
02-75
Rear Log
Middle Left Log
Front Left Log
Center Left Log
Front Bottom Log
Center Right Log
Middle Right Log
Embers
Vermiculite
Platinum Embers (supplied with packaged manual)
NOTE: If you will be installing the optional Brick Panels
(P36D & P90 only), install the Brick Panels prior
to installing the logs.
Model shown has P36D and P90 burner/grate with
brick panel option.
4)
Place Log 02-51 on the front right side of the burner. Push
the back of the log against the 2 brackets with the notch
on the bottom right side of the log fitting into the right side
of the grate.
02-75
02-75
02-51
02-51
02-54
02-55
02-53
Bracket
02-50
Bracket
02-52
02-51
The "02" reference numbers (i.e. 02-75) are
molded into the rear of each log.
1)
Carefully remove the logs from the box and unwrap them.
The logs are fragile, handle with care - do not force into
position.
2)
Sprinkle the vermiculite over base brick panel.
40
Notch
Notch
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
LOG SET INSTALLATION
5)
Position Log 02-53 across the cutouts in Logs 02-75 and
02-51 with the notch on the left side of the log fitting into
the 2nd grate tab.
02-53
02-75
5th Grate Tab
02-51
7)
Place the bottom left front edge of Log 02-55 against the
rear bracket on the burner tray and rest the log on the
cutout on Log 02-53.
Cutouts
2nd Grate Tab
02-51
02-53
02-75
02-55
6)
02-53
Position Log 02-54 across the cutouts in Logs 02-51 and
02-53. The notch in the bottom right end fitting against the
5th grate tab.
Rear Bracket
Cutouts
02-53
02-54
02-51
5th Grate Tab
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
41
INSTALLATION
8)
Place Log 02-52 between Logs 02-51 and 02-75 and on
the indentation on Log 02-54. The bottom right end sits
behind the rear grate tab.
9)
Sit Log 02-50 on the front left side of the burner. Push
the back of the log against the 2 front brackets with the
notch on the bottom of the log fitting into the first grate
tab.
02-50
02-53
02-52
02-51
02-54
Front Brackets
Log Indentation
02-55
02-53
Notch
02-50
02-52
02-54
Rear
Grate Tab
Photo shows rear grate tab.
Log 02-51 was removed to show the
positioning of Log 02-52.
42
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
10) Place the embers on the front of the burner tray in the
places shown on the photos below.
02-51
02-54
Separate platinum embers and place on the front burner on
and around the embers. Avoid stacking platinum embers.
Platinum embers may be placed over burner ports.
Do not block the burner ports in this
area adjacent to the Log 02-54
IMPORTANT
When placing Embers, do not block burner ports as
this can cause an incorrect flame pattern, carbon
deposits and delayed ignition.
Place embers in these 3 locations
on the burner tray.
11) Test fire to ensure proper light off (make sure flame flows
smoothly from one end of burner to the other). If there is
any flame hesitation, check that area for any blockage of
the burner ports.
02-5
2
02-75
02-50
02
-53
02-55
02-54
02-51
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
43
INSTALLATION
STANDARD FLUSH DOOR
The standard flush door comes with a black frame. To install the frame,
simply hook the top door flange onto the top of the unit and swing the
door towards the unit, see diagram 1.
Be careful that the glass gasket does not roll up; there must be a gap
between the gasket and the door lip to ensure that the door sits securely
on the unit, see Diagram 2.
Diagram 2
Diagram 1
Use the hook to pull the spring out until you can put the hook into the slot
on the bottom door bracket. Repeat for 2nd spring. See diagram 3.
Diagram 3
To remove the flush door, reverse the above steps.
44
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
REMOTE CONTROL
(OPTIONAL)
WALL SWITCH
(OPTIONAL)
WALL THERMOSTAT
(OPTIONAL)
Use the FPI Remote Control Kit approved for
this unit. Use of other systems may void your
warranty.
1) Run the wire through the right or left side
inlet opening. Be careful not to damage wire.
A wall thermostat may be installed if desired,
connect the wires as per the wiring diagram.
Use the table below to determine the maximum
wire length.
The remote control kit comes with a hand held
transmitter, a receiver and a wall mounting plate.
1) Choose a convenient location on the wall
to install the receiver and the receptacle
box (protection from extreme heat is very
important). Run wires from the fireplace to
that location. Use the Thermostat Wire Table.
2) Connect the two wires to the gas valve. See
diagram below.
Note: We recommend a maximum of 15'
of wire but if you wish to go with a
longer run, use the Thermostat Wire
Table.
2) Connect the wire to the wall switch and
install into the receptacle box.
CAUTION
Do not connect millivolt
wall switch wire to a 120V
wire.
Note: Preferable if the thermostat is installed
on an interior wall.
FPI offers an optional programmable thermostat
but any 250-750 millivolt rated non-anticipator
type thermostat that is CSA, ULC or UL approved
may be used.
CAUTION
Do not connect millivolt
wall thermostat wires
to a 120V wire.
Thermostat Wire Table
CAUTION
Do not connect millivolt
remote control wires to a
120V wire.
3) Install 3 AAA alkaline batteries in transmitter
and 4 AA alkaline batteries in the receiver.
Install the receiver and its cover in the wall.
Switch the remote receiver to "remote"
mode. The remote control is now ready for
operation.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
Recommended Maximum Lead Length
(Two-Wire) When Using Wall
Thermostat (CP-2 System)
Wire Size
14 GA.
16 GA.
18 GA.
20 GA.
22 GA.
Max. Length
50 Ft.
32 Ft.
20 Ft.
12 Ft.
9 Ft.
45
INSTALLATION
WIRING DIAGRAMS
This heater does not require a 120V A.C. supply for operation. In case of a power failure, the
burner switch and the optional remote control/
thermostat will continue to operate. However,
a 120V A.C. power supply is needed for the
fan/blower operation.
(Do not cut the ground terminal off under
any circumstances.)
NOTE:
Even if the fan is not purchased
with the unit, it is still a good idea
to bring power to the receptacle box
(provided with the unit) in case the
fan is installed at a later date.
For NATURAL GAS Units and Units NOT Equipped with DC Spark Boxes
Caution: Ensure that the wires do
not touch any hot surfaces and are
away from sharp edges.
46
CAUTION: Label all wires prior
to disconnection when servicing controls. Wiring errors can
cause improper and dangerous
operation.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
For PROPANE Units and Units Equipped with DC Spark Boxes*
*For installation of the DC Spark Box refer to the LP Conversion instructions in this manual.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
47
INSTALLATION
OPTIONAL FAN
INSTALLATION
6) Slide the thermodisc/cover assembly into
the bracket clip on the underside of the
firebox. Check that no wire will touch the
hot surfaces. Diagram 2.
120 Volt AC power is needed for the fan switch
and blower. The fan can be hard wired if desired.
The receptacle box should be installed on the left
hand side of the unit by a qualified electrician. The
neutral (wider) slot of the polarized receptacle
should be at the top.
11) Attach the two control boxes to the bottom
louver and tighten the 2 screws on the left
side and 1 screw on the right side.
Secure left
side with 2
screws.
Unit must be grounded at all times. Do
not cut the ground terminal off under any
circumstances.
1) Shut the power off.
Secure right side with one screw.
Diagram 2
2) Remove the standard flush door and the
optional bay door, if installed. Open the
bottom louver door.
7) Attach the Fan control box to the Burner
ON/OFF control box.
3) Loosen the 2 screws holding the Burner
ON/OFF switch and bracket to the bottom
louver and lift the assembly out.
4) Turn the fan base on its side (with the base
facing towards you) and then slide the fan
in towards the rear of the unit. Turn the fan
upright and slip it over the two mounting
studs. Take care not to damage the insulation
on the fan base. Ensure that the fan blades
do not rub against the valve tubing.
Diagram 1.
Use the clip & hook on the side of the control
boxes to join them together.
8) Secure the two boxes together with one
screw.
12) Secure the fan wires and power cord by
attaching one of the adhesive backed wire
holder clips (Part #910-199) onto the stove
base. Use the second clip to bundle up the
wires approximately 4" from the control box.
Ensure that there is no interference with the
wires when the louver is closed and that
no wire will touch the hot metal surfaces or
sharp edges.
13) Plug the fan power cord into the rear end of
the receptacle box to provide the maximum
clearance from the louvers.
OPTIONAL FAN REMOVAL
1) Shut the power off.
2) Reverse the above instructions.
Secure the 2 boxes together
with one screw.
9) Position the control box assembly on the
bottom louver and mark the position of the slot
on the right side bracket.
Note: The bearings are lubricated for life. Do
not lubricate them. Make sure you vacuum
the fan area on a regular basis.
IMPORTANT:
These fans collect a lot of dust from within
your home. Ensure you maintain these fan
motors on a regular basis by vacuuming
out the fan blades and housing using a soft
brush nozzle.
Diagram 1
5) Connect fan ground cable to ground lug.
Refer to wiring diagram.
Hold control box assembly in place and mark
the position of the right side slot
10) Remove the control box assembly and push
the hold-down clip onto the louver. Bend the
tab until it is at 90o to the louver.
48
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
OPERATING INSTRUCTIONS
INSTALLATION
OPERATING
INSTRUCTIONS
1) Read and understand these instructions
before operating this appliance.
2) Check to see that all wiring is correct and
enclosed to prevent possible shock.
3) Check to ensure there are no gas leaks.
3) Turn gas control knob counterclockwise
so indicator points to the "PILOT" position.
Depress the gas control knob fully. Depress
the igniter button several times until the
pilot lights. After approximately one minute,
release the gas control knob. The pilot flame
should continue to burn. If the pilot does not
remain lit, repeat operation allowing a longer
period before releasing gas control knob.
4) When the pilot stays lit, turn the gas knob
further counterclockwise to the "ON"
position.
4) Make sure the glass in the door frame is
properly positioned. Never operate the
appliance with the glass removed.
5) Use the wall switch, thermostat or remote
control to turn on the unit.
5) Verify that the venting and cap are
unobstructed.
6) Rotate the flame height regulator to adjust
the flame height higher or lower.
6) Ensure that the brick panels are installed.
During the first few fires, a white film
may develop on the glass front as part
of the curing process. The glass should
be cleaned or the film will bake on and
become very difficult to remove. Use a
non-abrasive cleaner and NEVER clean
the glass while it is hot.
AERATION
ADJUSTMENT
The air shutter can be adjusted by moving the
adjusting wire up or down. The wire is accessed
through the bottom louver opening. Open the air
shutter for a blue flame or close for a yellower
flame. The burner aeration is factory set but
may need adjusting due to either the local gas
supply or altitude.
Minimum Air Shutter Opening:
3/16"
Natural Gas
1/4"
Propane
7) Verify log placement. If the pilot cannot be
seen when lighting the unit, the logs have
been incorrectly positioned.
SHUTDOWN
PROCEDURE
8) The unit should never be turned off, and on
again without a minimum of a 60 second
wait.
1) Use the wall switch, thermostat or remote
control to turn off the main burner.
CAUTION: Carbon will be produced if air shutter
is closed too much.
2) Turn the main gas control clockwise to the
"OFF" position to turn off the pilot.
Note: Any damage due to carboning
resulting from improperly setting
the aeration controls is NOT covered
under warranty.
3) Turn off all electric power to appliance if
service is to be performed.
FIRST FIRE
LIGHTING
PROCEDURE
IMPORTANT
To ignite or reignite the pilot, you
must first release the tension springs
below the door.
Only when the pilot holds, without pressure
being applied to the control knob, reapply the
tension springs to the door. The unit must
not be operated with the tension springs
unattached.
NOTE: For all propane units and units
equipped with electric spark boxes,
see "Copy of Lighting Plate Instructions" section for more details.
IMPORTANT Gas on/off knob cannot be
turned from "PILOT" to "OFF" unless it is
partially depressed.
1) Turn burner OFF using "ON/OFF" switch.
2) Turn gas control knob so indicator points
to "OFF" position and allow 5 minutes for
any gas in the combustion chamber to
escape.
Note: Aeration Adjustment should only
be performed by an authorized FPI
Installer at the time of installation or
service.
The first fire in your fireplace is part of the paint
curing process. To ensure that the paint is
properly cured, it is recommended that you burn
your fireplace for at least four (4) hours the first
time before you use it with the fan on.
When first operated, the unit will release an odour
caused by the curing of the paint, the burning
off of any oils remaining from manufacturing.
Smoke detectors in the house may go off at
this time. Open a few windows to ventilate the
room for a couple of hours.
The glass panel may require cleaning after the
unit has cooled down. DO NOT ATTEMPT
TO CLEAN THE GLASS WHILE IT
IS HOT.
Note: When the glass is cold and the
appliance is lit, it may cause
condensation and fog the glass.
This condensation is normal and will
disappear in a few minutes as the
glass heats up.
DO NOT BURN THE APPLIANCE
WITHOUT THE GLASS FRONT IN
PLACE.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
Adjustment Wire: Push to close or pull to
open aeration cap.
Closed - Tall yellow
Open - Short Blue
NORMAL OPERATING
SOUNDS OF GAS
APPLIANCES
It is possible that you will hear some sounds
from your gas appliance. This is perfectly normal
due to the fact that there are various gauges
and types of steel used within your appliance.
Listed below are some examples. All are normal
operating sounds and should not be considered
as defects in your appliance.
49
OPERATING INSTRUCTIONS
COPY OF THE LIGHTING PLATE INSTRUCTIONS
Blower:
FPI gas appliances use high tech blowers to
push heated air farther into the room. It is not
unusual for the fan to make a "whirring" sound
when ON. This sound will increase or decrease
in volume depending on the speed setting of
your fan speed control.
Burner Tray:
The burner tray is positioned directly under the
burner tube(s) and logs and is made of a different
gauge material from the rest of the firebox and
body. Therefore, the varying thicknesses of steel
will expand and contract at slightly different
rates which can cause "ticking" and "cracking"
sounds. You should also be aware that as there
are temperature changes within the unit these
sounds will likely re-occur. Again, this is normal
for steel fireboxes.
Blower Thermodisc:
When this thermally activated switch turns ON
it will create a small "clicking" sound. This is the
switch contacts closing and is normal.
Pilot Flame:
While the pilot flame is on it can make a very
slight "whisper" sound.
Gas Control Valve:
As the gas control valve turns ON and OFF, a
dull clicking sound may be audible, this is normal
operation of a gas regulator or valve.
Unit Body/Firebox:
Different types and thicknesses of steel will
expand and contract at different rates resulting
in some "cracking" and "ticking" sounds will be
heard throughout the cycling process.
OFF
MAINTENANCE
INSTRUCTIONS
1) Always turn off the gas valve before cleaning.
For relighting, refer to lighting instructions.
Keep the burner and control compartment
clean by brushing and vacuuming at least
once a year. When cleaning the logs, use a
soft clean paint brush as the logs are fragile
and easily damaged.
2) Clean appliance and door with a damp
cloth (never when unit is hot). Never use
an abrasive cleaner. The glass should be
cleaned with a gas fireplace glass cleaner.
The glass should be cleaned when it
starts looking cloudy.
3) The heater is finished in a heat resistant
paint and should only be refinished with
heat resistant paint. FPI uses StoveBright
Paint - Metallic Black #6309.
a
50
4) Make a periodic check of burner for proper
position and condition. Visually check the
flame of the burner periodically, making sure
the flames are steady; not lifting or floating.
If there is a problem, call a qualified service
person.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
MAINTENANCE
5) The appliance and venting system must be
inspected before use, and at least annually,
by a qualified field service person, to ensure
that the flow of combustion and ventilation
air is not obstructed.
Note: Never operate the appliance without
the glass properly secured in place.
6) Do not use this appliance if any part has been
under water. Immediately call a qualified
service technician to inspect the appliance
and to replace nay part of the control system
and any gas control which has been under
water.
7) Verify operation after servicing.
LOG REPLACEMENT
DOOR GLASS
The unit should never be used with broken logs.
Turn off the gas valve and allow the unit to cool
before opening door and carefully remove the
logs. (The pilot light generates enough heat to
burn someone.) If for any reason a log should
need replacement, you must use the proper
replacement log. The position of these logs
must be as shown in the diagrams under Log
Installation.
Your FPI fireplace is supplied with high
temperature, 5 mm Neoceram ceramic glass
that will withstand the highest heat that your unit
will produce. If your glass requires cleaning, we
recommend using an approved glass cleaner
available at all authorized dealers. Do not use
abrasive materials. Do not clean the glass
when hot.
Note: Improper positioning of logs may
create carbon build-up and will
severely alter the unit's performance
which is not covered under warranty.
GENERAL VENT
MAINTENANCE
Conduct an inspection of the venting system
semi-annually. Recommended areas to inspect
as follows:
1) Check the Venting System for corrosion in
areas that are exposed to the elements.
These will appear as rust spots or
streaks, and in extreme cases, holes.
These components should be replaced
immediately.
2) Remove the Cap, and shine a flashlight
down the Vent. Remove any bird nests, or
other foreign material.
3) Check for evidences of excessive
condensation, such as water droplets forming
in the inner liner, and subsequently dripping
out the joints, Continuous condensation can
cause corrosion of caps, pipe, and fittings. It
may be caused by having excessive lateral
runs, too many elbows, and exterior portions
of the system being exposed to cold weather.
THERMOPILE/
THERMOCOUPLE
1) Open the bottom louvers.
2) Loosen the thermocouple or thermopile with
a 7/16" wrench.
3) Disconnect thermocouple by loosening
nut from the valve with a 9mm wrench.
Disconnect thermopile by loosening 2
screws marked TP on the valve.
4) Drop the thermocouple or thermopile down
from the bracket and pull it out of the unit.
In the event that you break your glass by impact,
purchase your replacement from an authorized
FPI dealer only, and follow our step-by-step
instructions for replacement.
WARNING: Do not operate the
appliance with the glass panels
removed, cracked or broken.
Replacement of the glass panels
should be done by a licensed or
qualified service person.
Caution: Wear gloves when removing
damaged or broken glass.
FLUSH GLASS REPLACEMENT
Remove the flush door front. Remove the 4
glass clips from each corner. Slide in the new
replacement glass. Push the 4 glass clips
back onto the frame. The glass must have
gasketing around it.
5) Reinstall the new ones in reverse order.
GLASS GASKET
If the glass gasket requires replacement use
5/8" flat glass gasket for the Bay Front (Part
# 936-243) and a tadpole glass gasket for the
Flush Front (Part # 936-155).
4) Inspect joints, to verify that no pipe
sections or fittings have been disturbed,
and consequently loosened. Also check
mechanical supports such as Wall Straps,
or plumbers' tape for rigidity.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
51
MAINTENANCE
REMOVING VALVE
7) Lift out the bottom brick panel.
16) Remove the 4 Phillips head screws from
the sides of the valve bracket and remove
valve.
1) Shut off the gas supply.
Hint:
2) Remove the louvers (and bay door if it is
on).
3) Open the flush door and remove the door.
4) Remove the logs.
5) Remove the burner/grate assembly by
removing the two Phillips head screws and
then lift the burner assembly out.
If you are using black pipe, ensure
that there is a union by the valve,
otherwise removal will be almost
impossible.
INSTALLING VALVE
8) Disconnect the inlet gas line. See diagram
2.
9) Disconnect the 2 TP wires and the 2 TH
wires from the valve.
10) Remove the 10 Phillips head screws securing
the valve tray assembly in place and then
lift the entire assembly out.
1) Attach the valve to the valve bracket with
the 4 (m5x8 metric) screws provided.
2) Reconnect the "gas out" flare fitting with an
11/16" wrench.
3) Reconnect the "gas out" flare nut with a
13/16" wrench.
4) Install piezo ignitor push button assembly
and reconnect wire.
5) Reconnect the quick drop out thermocouple
nut with a 9mm wrench.
6) Reconnect the pilot tube nut with a 7/16"
wrench.
7) Scrape off the old gasket from the floor of the
firebox and from the valve tray assembly.
Diagram 1: Remove the left and right screws
and then lift out the
burner/grate assembly.
screws
8) Install a new gasket and reinstall the valve
tray assembly.
Valve Tray Assembly
Note:
6) Remove the rear log stand by removing the
2 screws.
screws
Failure to install a new gasket
may severely affect the appliance
performance.
9) Reinstall the 10 hold down screws.
Rear Log Stand
10) Hook up the 2 TP and 2 TH wires to the
appropriate connections on the valve.
11) Reinstall the bottom brick panel and the
front log stand.
12) Install Burner/grate assembly
13) Hook up the gas line and check for gas
leaks with a soap and water solution or a
gas leak detector. (Do not use open flame
for leak testing.)
11) Undo the pilot tube from the valve with a
7/16" wrench.
12) Undo the quick drop out thermocouple nut
on the valve with a 9mm (metric) wrench.
13) Remove the Piezo igniter wire and push
button assembly.
14) Fire up the unit temporarily
15) Check the manifold pressure.
16) Reinstall the logs and brick panels as
needed.
17) Close the door and replace the louvers.
14) Undo the "gas out" flare nut with a 13/16"
wrench.
18) Fire up the unit again and check for proper
flame appearance and glow on logs.
15) Undo the "gas out" flare fitting with an 11/16"
wrench.
52
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
®
REGENCY
OPTIONS
INSTALLATION
FLUSH LOUVERS
1) Install the top louver by sliding the two
bracket clips into the brackets located
underneath the top of the firebox.
2) The bottom louver has a hinge that is
attached (2 screws per hinge) to the lip on
bottom of the unit.
3) Open the bottom louver. Pull the Burner
ON/OFF control box from inside the bottom
of the fireplace and position the slots in the
bracket over the 2 screws on the left side
of the bottom louver. Push down to lock into
place. Tighten the screws.
Note: Top and
bottom louvers are
different.
Screws on
louver bracket
Burner ON/OFF
control box
Burner ON/
OFF control
box attached
to bottom
flush louver.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
53
REGENCY® OPTIONS
FULL SCREEN DOOR INSTALLATION
1) Before beginning the installation, remove the Screen Doors from the
Full Screen Door Frame by fully opening the doors and lifting up off
of the hinges. See important note in step 7.
2) Full Screen Door Frame Installation
Cut-Out
a) Before attaching the Full Screen Door Frame to the unit, loosen the
left and right side #8 Philips Head Screws located on the inside top
of the outer frame of the appliance. Also remove the center screw.
Oblong Hole
Loosen the #8 Philips Head Screw on the inner side of each hinge
bracket as shown below.
Inside Top
of Outer
Frame
Cut-Out
Top
Flange
Bottom
Flange
Backside of Full
Screen Door
Frame Shown
Cut-Outs
NOTE: Should the finished wall protrude beyond the face of the unit,
you can accommodate up to 1/2" depth.
Simply push in the Full Screen Door Frame until it aligns against
the finished wall. Secure Top Flange of Full Screen Door Frame as
described in step 2.
Hinge
Bracket
For the Bottom Flange of the Full Screen Door Frame, push the
bottom of the Frame until it aligns with the wall. Use the inner cut-outs
to secure the base of the Frame using the 2 x Hex Head Drill Point
Screws provided.
Inner Hinge
Bracket Screw
b) Slide the cut-outs in the Top and Bottom Flange of the Full Screen
Door Frame under the screw heads which were loosened in step
2a. Once the Frame is in place, tighten the screws to secure. Also
re-secure the top center screw through the oblong hole.
Bottom
Flange
Inner
Cut-Outs
Backside of Full Screen
Door Frame Shown
54
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
®
REGENCY
OPTIONS
INSTALLATION
6) Slide the Top Grill into the louver brackets located on the inside top
of the firebox. Push in place.
3) Install the hinges to the hinge brackets on the left and right side of the
bottom of the outer frame, secure using 2 x #8 Philips Head Screws
per hinge.
Top Grill
4) Place the Bottom Grill near hinge. Flip the hinge over the Bottom Grill
and secure with 3 x #8 Phillips Head Screws per side.
7) Install the Left and Right Side Screen Doors in the fully open position
by placing over top of the hinges on the Full Screen Door Frame.
Hinge Location
NOTE: Failure to install the doors in the fully open position could
result in paint damage to the surface of the door.
Bottom Grill
Hinge
5) Mount the Burner ON/OFF Control Box to the left side of the Bottom
Grill using 2 x #8 - 1/4" Philips Head Screws.
Left Side
of Bottom
Grill
Screen Door
8) Close screen doors.
Burner ON/OFF
Control Box
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
55
REGENCY® OPTIONS
TRIPOLI SCREEN DOOR
When installing the optional Tripoli Screen Door Series, a non-combustible material 12" (305mm) above the unit and 6" (153mm)
on each side must be used (see Diagram 1).
The Tripoli Screen Door Series also requires steel stud framing above and on each side of the unit (refer to Diagram 1).
Min. 14-1/4" (362mm)P36
Min. 18-5/8" (473mm)P36D
Min. 14-1/4" (362mm)P36
Min. 18-5/8" (473mm)P36D
Diagram 1
Steel
Stud
Steel
Stud
Min. 361/4”
(921mm)
Steel
Stud
Steel
Stud
Min. 361/4”
(921mm)
Option #2:
Fireplace with 1" (25mm or more) Facing Material
Option #1:
Fireplace with 1/2" (13mm) Facing Material
INSTALLATION NOTE:
The hearth material must be brought past the Tripoli frame all the way to the unit
face, so there will be no gap between the face and the actual fireplace.
FRAMING DIMENSIONS
P36
OPTIONS
P36D
A
B
C
D
A
B
C
D
1
36-1/4”
(921mm)
36-1/4”
(921mm)
14-1/4”
(362mm)
46”*
(1168mm)
36-1/4”
(921mm)
37-1/4”
(946mm)
18-5/8”
(473mm)
46”*
(1168mm)
2
36-1/4”
(921mm)
36-1/4”
(921mm)
13-3/4”
(349mm)
46”
(1168mm)
36-1/4”
(921mm)
37-1/4”
(946mm)
18-1/8”
(460mm)
46”
(1168mm)
* 'D' is Minimum height to combustible materials including the Minimum 2" (51mm) Top clearance to the Horizontal Vent.
56
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
®
REGENCY
OPTIONS
INSTALLATION
Note: The facing material has to go on after the unit is set.
1) Remove Glass Door. Refer to P36 Manual.
4) Place bracket under the Flange. Secure with 2 screws as indicated
in Diagram 4.
2) Remove 2 screws and bracket as indicated (refer to Diagram 2).
Remove bracket
Remove both screws
Diagram 4
Diagram 2
5) Loosen the 3 x #8 Phillips Head Screws located on the inside top
of the outer frame of the appliance (refer to Diagram 5).
3) Install On/Off switch (refer to Diagram 3).
On/Off Switch
3 x #8 Phillips
Diagram 3
Diagram 5
Control
Mounting
Bracket
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
57
REGENCY® OPTIONS
6) Install Top Support Frame
Slide in the Top Support Frame using the slots as a guide. Secure
and re-tighten the screws to the unit.
8) Attach Top and Side Support Frame
a) Ensure the Side Supports are aligned with the correspond
hole on the Top Support Frame, then secure with 1 screw.
b) Repeat step on the other side.
Cut-Outs
View of backside of Top Support Frame.
Note: The Nailing Strips can be adjusted, depending on the fac
material (as indicated in Diagram 7).
7) Side Support Frame
a) Mount Side Support Frame to unit as shown in Diagram 6, then
secure with 2 screws on each side.
b) Repeat step on the other side.
1/2” Facing
Material
1” Facing
Material
Diagram 7
9) Optional
Install Optional 3-Panel Arch Door. (Refer to Install 3-Panel A
Door Instruction Sheet).
Diagram 6
58
10) Change in Logo
Replace existing logo with Regency logo.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
PARTS LIST
MAIN ASSEMBLY
1)
2)
3)
4)
6)
7)
8)
9)
10)
20)
22)
23)
24)
27)
28)
29)
30)
Part #
Description
Part #
Description
948-253
510-026
948-045
948-115
430-129
910-429
910-428
910-430
904-687
510-033
780-010
780-011
780-013
*
*
*
*
Door Handle
Hinge Bracket - Left/Right
Chain
Spring
Receptacle Box Mount
Box - Receptacle
Duplex Receptacle
Cover - Receptacle
Clamp Connector
Top Nailing Strip
Baffle Plate
Standoff - Top
Standoff - Side/Back
Outer Flue Collar
Inner Flue Collar Assy
Flue Mounting Plate
Gasket for Flue Collar
780-901
780-902
780-903
Brick Panel Set - Standard Brown
Brick Panel Set - Standard Red
Brick Panel Set - Herringbone Brown
*
*
*
*
*
Brick Panel - Back
Brick Panel - Left
Brick Panel - Right
Brick Panel - Bottom
Thermodisc Bracket
31)
32)
33)
34)
35)
432-967
38) 910-241
910-899
Description
910-813
910-330
904-586
910-199
910-142
Power Cord (120 Volts)
Fan Speed Control Switch
Knob - Speed Control
Wire Holder Clip
Thermodisc-Fan (Auto
ON/OFF)
Wire Harness - Plug In Fan
Optional Rigid Pipe Adaptor
910-845
50) 510-994
Burner ON/OFF Switch Assy
Switch-Burner ON/OFF(3-way)
Wire Harness-Valve to Burner
432-917
Fan & Speed Control Assy
(120 Volts) Optional
42) 910-331/P Fan Motor
432-966 Fan Switch Assy (120 Volts)
Optional
89
43)
46)
47)
48)
49)
Part #
93
94
50
89)
90)
91)
92)
93)
94)
95)
96)
97)
98)
99)
946-556
946-004
946-000
946-002
946-001
946-007
946-517/P
Optional Heat Wave Duct Kit
Junction Box
Round Duct Adaptor
Round to Oval Adaptor
Oval Duct Adaptor
Angle Bracket
Fan Assembly - HeatWave
Option
946-006 Grill Plate - White
946-005/01 Wall Adaptor Plate - White
910-417 Knob - White
910-366 Switch Cover Plate - White
910-412 Fan Speed Controller
93
100) 910-367
29
92
101) 690-022
102) 946-010
946-011
30
91
95
96
102
100
946-570
28
22
105) 910-165
106) 946-000
30
99
27
23
97
98
918-522
514-969
90
Heat Release Duct Kit
(Optional)
Fan (120 Volts)
Flexible Air Release Duct
Manual
Conversion Kit - NG to LP
*Not available as a replacement part.
23
20
Box - Plastic Switch
Receptacle
Cover Plate - Outer Box Side
Flexible Air Duct
Insulation 6" dia. x 24"
24
DOORS & LOUVERS PLEASE
REFER SEPARATE SECTION
10
6
106
2
7
31
8
4
9
3
101
1
35
2
24
105
34
32
42
49
BRICK PANEL SET
33
38
ON-OFF
SWITCH
ASSEMBLY
HEAT RELEASE DUCT KIT
48
43
47
46
FAN SWITCH ASSEMBLY
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
59
PARTS LIST
BURNER ASSEMBLY & LOG SET
52)
53)
54)
55)
56)
57)
58)
65)
66)
67)
68)
69)
75)
76)
79)
82)
83)
84)
85)
Part #
Description
910-190
780-021
910-421
910-422
Piezo Ignitor & Nut
Gasket - Valve Access Plate NG/LP
Pilot ON/OFF 3" Extension Knob
Flame HI/LOW 3" Extension Knob
780-574/P
780-576/P
*
910-478
*
*
910-038
910-039
*
W840470
904-240
904-390
936-170
Valve Assy - Natural Gas
Valve Assy - Propane
Valve Tray - NG/LP
Valve - S.I.T. - Natural Gas / Propane
Valve Bracket
Pilot Bracket
Pilot Assy - S.I.T. - 3 Flame NG
Pilot Assy - S.I.T. - 3 Flame LP
Pilot Holder
Pilot Assembly Gasket
Orifice #37 - Natural Gas
Orifice #52 - Propane
Orifice Gasket
*
*
*
791-535
511-030
780-028
*
780-930
Firebox Base
Deflector - Left
Deflector - Right
Burner Assy - NG/LP
Burner Grate Assy
Rear Log Support Bracket
Deflector
Log Set
*Not available as a replacement part.
60
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
PARTS LIST
REGENCY® FLUSH FRONT ASSEMBLY
Part #
Description
Part #
132) 512-518
135) 940-090/P
136) 936-155
904-691
Flush Door Assembly
Glass (Flush)
Glass Gasket (Tadpole)
U-Clip
510-920
510-921
510-922
510-923
138) *
139) *
Flush Louvers (Set)-Gold/Blk
Flush Louvers (Set)-Brass/Blk
Flush Louvers (Set)-Black
Flush Louvers (Set)-Steel/Black
Flush Louver Assy-Top
Flush Louver Assy-Btm
157)
158)
159)
161)
510-986
*
*
*
948-216
Description
Finishing Trim (Set) - Black
Finishing Trim Left
Finishing Trim Top
Finishing Trim Right
Regency® Logo Plate
*Not available as a replacement part.
138
132
158
139
161
157
159
136
135
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
61
NOTES
62
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
WARRANTY
Regency Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully inspects each unit
thoroughly before it leaves our facility. FPI Fireplace Products International Ltd. is pleased to extend this limited lifetime warranty to the original purchaser of a
Regency Product. This warranty is not transferable.
The Warranty: Limited Lifetime
The combustion chamber, heat exchanger, burner tubes/pans, logs, brick panels and gold plating (against defective manufacture only) are covered under the Limited Lifetime
Warranty for five (5) years for parts and subsidized labour* and parts only thereafter.
Glass is covered for lifetime against thermal breakage only, parts and subsidized labour* for five (5) years and parts only thereafter from date of purchase.
External casting, surrounds and grills are covered against cracks and warps resulting from manufacturer defects, parts and subsidized labour* for three (3) years from the date
of purchase and parts only thereafter.
Special Finishes - One year on brushed nickel and antique copper full screens and doors. You can expect some changes in color as the product "ages" with constant heating
and cooling. FPI warranties the product for any manufacturing defects on the original product. However, the manufacturers warranty does not cover changing colors and marks,
ie. finger prints, etc applied after the purchase of the product. Damage from the use of abrasive cleaners is not covered by warranty.
Electrical and mechanical components such as blowers, switches, wiring, thermodiscs, FPI remote controls, spill switches, thermopiles, thermocouples, pilot assembly components,
and gas valves are covered for two years parts and one year subsidized labour* from the date of purchase. Blowers and valves replaced under warranty are considered repairs and
continue as if new with appliance. ie. twelve (12) months from original purchase date of appliance with a minimum of three (3) months coverage from date of replacement.
FPI venting components are covered parts and subsidized labour* for three (3) years from date of purchase.
Simpson Dura-Vent venting components (Direct Vent units) are covered by Simpson Dura-Vent Inc. warranty.
Repair/replacement parts purchased by the consumer from FPI after the original coverage has expired on the unit will carry a 90 day warranty, valid with a receipt only. Any
item shown to be defective will be repaired or replaced at our discretion. No labor coverage is included with these parts.
Conditions:
Any part or parts of this unit which in our judgement show evidence of such defects will be repaired or replaced at FPI's option, through an accredited distributor or agent provided
that the defective part be returned to the distributor or agent Transportation Prepaid, if requested.
Porcelain/Enamel - Absolute perfection is neither guaranteed nor commercially possible. Any chips must be reported and inspected by an authorized dealer within three days of
installation. Reported damage after this time will be subject to rejection.
It is the general practice of FPI to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to FPI and evaluated
for manufacturer defect.
The authorized selling dealer is responsible for all in-field service work carried out on your Regency product. FPI will not be liable for results or costs of workmanship from
unauthorized service persons or dealers.
At all times FPI reserves the right to inspect product in the field which is claimed to be defective.
All claims must be submitted to FPI by authorized selling dealers. It is essential that all submitted claims provide all of the necessary information including customer name,
purchase date, serial #, type of unit, problem, and part or parts requested, without this information the warranty will be invalid.
Exclusions:
This limited Lifetime Warranty does not extend to or include paint, door or glass gasketing or trim.
At no time will FPI be liable for any consequential damages which exceed the purchase price of the unit. FPI has no obligation to enhance or modify any unit once manufactured.
ie. as products evolve, field modifications or upgrades will not be performed.
FPI will not be liable for travel costs for service work.
Installation and environmental problems are not the responsibility of the manufacturer and therefore are not covered under the terms of this warranty policy.
Embers, rockwool, gaskets, door handles and paint are not covered under the terms of this warranty policy.
Any unit which shows signs of neglect or misuse is not covered under the terms of this warranty policy.
The warranty will not extend to any part which has been tampered with or altered in any way, or in our judgment has been subject to misuse, improper installation, negligence
or accident, spillage or downdrafts caused by environmental or geographical conditions, inadequate ventilation, excessive offsets, negative air pressure caused by mechanical
systems such as furnaces, fans, clothes dryer, etc.
Freight damage to stoves and replacement parts is not covered by warranty and is subject to a claim against the freight carrier by the dealer.
FPI will not be liable for acts of God, or acts of terrorism, which cause malfunction of the appliance.
Performance problems due to operator error will not be covered by this warranty policy.
Products made or provided by other manufacturers and used in conjunction with the operation of this appliance without prior authorization from FPI, may nullify your warranty
on this product.
Any alteration to the unit which causes sooting or carboning that results in damage to the interior / exterior facia is not the responsibility of FPI.
* Subsidy according to job scale as predetermined by FPI.
Regency® P36D-1 Zero Clearance Direct Vent Gas Fireplace
63
Register your Regency® warranty online
www.regency-fire.com
Reasons to register your product online today!
• View and modify a list of all your registered products.
• Request automatic email notification of new product updates.
• Stay informed about the current promotions, events, and special
offers on related products.
Installer: Please complete the following information
Dealer Name & Address: ______________________________________________
___________________________________________________________________
Installer: ___________________________________________________________
Phone #: ___________________________________________________________
Date Installed: ______________________________________________________
Serial No.: __________________________________________________________
3FHJ
3F
HJTU
TUFS
UFSƔZZPV
PVSSƔ8
8BSS
8BSS
8B
SSBO
BOUZ
BO
UZƔBBOEEƔCF
CFƔBBVU
BVUPNB
UPNBUJUJUJDB
DBMMMMMMZZƔFO
FOUF
UFSF
SFEEƔUP
UPƔ
7).Ɠ!Ɠ&)2%4!",%
2EGISTERƓONLINEƓATƓ
IUUQSFHFODZGJSFDPNƔ
$VTUPNFS$BSFBTQY
4FFƔXFCTJUFƔGPSƔTXFFQTUBLFTƔSVMFT
Panorama, AstroCap,Tripoli, HeatWave and Heat Release are trademarks of FPI
Fireplace Products International Ltd.
© Copyright 2012 FPI Fireplace Products International Ltd. All rights reserved.
Printed in Canada
Download PDF