Park Assist, camera_31260504_en

Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
XC90
Section Group Weight(Kg/Pounds) Year
3
366 1 (2.1)
Month
2007 05
XC90 2003, XC90 2004, XC90 2005, XC90 2006, XC90 2007, XC90 2008, XC90 2008, XC90 2009, XC90 2009, XC90 2010
IMG-242200
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 1 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Required tools
A0000162
IMG-239660
IMG-239942
IMG-240693
IMG-239981
IMG-246925
IMG-240675
IMG-239664
IMG-242205
IMG-274123
IMG-213320
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 2 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 3 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
INTRODUCTION
Park Assist, camera
Note!
●
NOTE! Read through the entire text before carrying out
any work.
●
The front page gives the date of this edition and the edition it
replaces
●
The second page shows the tools needed for the installation and
the contents of the installation kit
●
The illustrations display the procedure in order of operation. The
order of operation is repeated in the text section
●
Cut out the text page in order to follow the illustrations and text at
the same time.
© VolvoCar Corporation, 2007 Printed in Sweden
For cars with an accessory electronic module (AEM), the existing cable
harness between the accessory electronic module (AEM) and the rear
electronic module (REM) must be replaced (steps 51-66). The new
cable harness is marked (A) in the kit image.
31260504
Page 4 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Installing the camera
1
●
Remove the number plate and holder.
IMG-242207
Installing the camera
2
●
Apply tape to the boot lid to protect the finish.
IMG-242208
Installing the camera
3
●
Position the template as illustrated.
IMG-242209
Installing the camera
4
●
Make a mark according to the template's inner rectangle.
IMG-242210
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 5 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Installing the camera
5
●
Use a short drill bit and drill holes according to the template.
Note!
Do not drill through the template.
IMG-242211
Installing the camera
6
●
Drill three overlapping holes as illustrated.
Note!
Use a short drill bit.
IMG-242212
Installing the camera
7
●
Cut out along the inside of the marking. The marking should still be visible.
●
Clean up the saw cuttings using a vacuum.
IMG-242213
Installing the camera
8
●
Open the boot lid fully.
IMG-242214
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 6 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Installing the camera
9
●
Remove the border around the handle by pressing in the two catches with a
screwdriver (1) and at the same time pry up the outer edge using a weatherstrip
tool (2).
IMG-242215
Installing the camera
10
●
Remove the lamp.
●
Unplug the connector.
IMG-242216
Installing the camera
11
●
Remove the screws.
●
Pull the panel downwards until all the clips release.
IMG-242218
Installing the camera
12
●
Remove the centre panel and the right-hand side panel.
IMG-242219
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 7 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Installing the camera
13
●
Mark out and drill with the holesaw as illustrated.
●
Vacuum.
IMG-242220
Installing the camera
14
●
Mark out and drill with the holesaw as illustrated.
●
Vacuum.
IMG-242221
Installing the camera
15
●
Applies to cars without vibration damper
Mark out and saw out the hole as illustrated.
●
Vacuum.
IMG-242222
Installing the camera
16
●
Applies to cars with vibration damper installed
Remove the vibration damper by removing the three screws.
IMG-246926
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 8 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Installing the camera
17
R8504201
●
Remove the rear roof panel covers and the screws beneath them.
●
Carefully pry off the panel at the rear edge. Use a plastic weatherstrip tool.
●
Pull the rear edge of the panel downwards until the four clips on the top release.
●
If the car is equipped with lighting in the panel, unplug the connector from the
panel.
●
Pull the panel backwards to release it.
Installing the camera
18
●
Disconnect the washer hose.
IMG-242224
Installing the camera
19
●
Loosen the rubber pass-through and pull out the washer hose.
IMG-242225
Installing the camera
20
●
Take the tail that is foam-covered about 100 mm on the cable to camera lens and
thread through the hole.
IMG-242226
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 9 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Installing the camera
21
●
Insert the cable through the rubber grommet. The end of the grommet that has a
lip should sit in the body and the part without a lip should sit in the cargo
compartment. The rubber grommet should sit on the part of the cable that is not
foam-covered.
IMG-242227
Installing the camera
22
●
Thread a wire or cable through the drilled hole down to the washer hose.
IMG-242228
Installing the camera
23
●
Tape the cable to the camera on the wire or cable that has been threaded
through the hole.
IMG-242230
Installing the camera
24
●
Route the cable out through the hole.
IMG-242231
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 10 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Installing the camera
25
●
Press the cable clip in the hole. If the hole is being used, secure it by the existing
cable with a cable tie.
IMG-242232
Installing the camera
26
●
Refit the rubber pass-through and adjust the length of the cable from the clip to
the rubber pass-through.
IMG-242233
Installing the camera
27
●
Route the cable between the rear window and lid as illustrated.
IMG-242234
Installing the camera
28
●
Thread the cable through the hole.
IMG-242235
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 11 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Installing the camera
29
●
Place the template over the hole for the camera lens (inside the lid).
Note!
Position it the same way/direction as when marking the hole in section 4.
IMG-242236
Installing the camera
30
●
Route the cable through the template and hole.
IMG-242237
Installing the camera
31
●
Fit the cable connector on the camera lens.
IMG-242238
Installing the camera
32
●
Screw the right-hand screw fully in the camera.
●
Align the template so that the right-hand hole in the template is directly above the
right-hand hole in the lid.
Hold the template in position (inside the hole in the lid) and, at the same time,
tighten the camera's right-hand screw so it holds.
●
Align the left-hand holes with each other, fit the screw and tighten the camera.
IMG-242239
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 12 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Cargo compartment, preparations
33
●
Applies to cars with two rows of seats
Fold up the floor hatch (1). If the floor hatch is equipped with a grocery bag
holder, the holder is secured with a strap on both ends of the storage
compartment. Detach the straps.
●
Remove the storage compartment under the floor hatch.
●
Remove the floor hatch by folding it almost completely closed and pulling it
backwards from the mountings until it releases.
IMG-242240
●
●
●
Applies to cars with three rows of seats and integrated carrier bag
holder on the underside of the floor hatch
Fold up the floor hatch (1).
Detach the two straps on the panel under this. Lift up the rear edge of the panel,
fold the floor hatch back towards the panel and lift out the floor hatch with the
panel.
Applies to cars with three rows of seats without an integrated carrier
bag holder
Fold up the floor hatch (1) at the rear edge and lift it out.
Cargo compartment, preparations
34
●
Slide the driver's seat fully forwards and then fully upwards from the rear edge.
●
Turn the ignition key to position 0.
●
Remove the three screws in the battery holder. Lift the battery holder out.
●
Remove the battery cover.
●
Disconnect the battery negative lead.
R3100130
Cargo compartment, preparations
35
●
Remove the hatch on the left-hand side of the cargo compartment.
IMG-242241
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 13 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Cargo compartment, preparations
36
●
Remove the panel.
●
Pull off the rubber strip on the rear edge of the door opening for the left-hand
rear door opposite the left C-post panel.
●
Carefully pry off the left-hand C-post panel sides at the top. Use a plastic
weatherstrip tool. Then pull until the three clips on the inside release. Do not
damage the headlining or the panel.
●
If a headphone socket is mounted, disconnect the connector to such.
●
Remove the panel by pulling upwards slightly and unhooking it from the side
panel.
●
Carefully loosen the D-post panel. Start from the top and continue downwards
until the three clips on the inside have released.
●
Disconnect the connector on the D-post panel (if the car has a loudspeaker in
the D-post, the connector is on the loudspeaker).
●
Remove the panel by pulling upwards slightly and unhooking it from the side
panel.
●
Fold out the load securing eyelet.
●
Take a scriber or special tool part no.9995919 and insert the angled tip in the hole
in the top edge of the cover.
●
Twist the scriber so it grips the rear of the cover (1) and pull it loose. This should
be carried out on both the front and rear load securing eyelets.
IMG-242242
37
R3903738
38
R8504123
39
R8504313
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 14 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
40
●
Applies to cars with two rows of seats
Remove the screws (2) on the load securing eyelets.
●
Remove the cover (3), by prying off using a weatherstrip tool or a small screw
driver.
●
Remove the screws (4).
●
Remove the panel by pulling out the upper edge slightly so that the clips on the
inside release. Pull the panel straight up.
●
Fold up the left-hand seat in the third row of seats.
●
Remove the screws (2) on the load securing eyelets.
●
Remove the cover (3), by prying off using a weatherstrip tool or a small screw
driver.
●
Remove the screws (4).
●
Remove the clip (5) in the bottom of the storage compartment.
●
Remove the panel by pulling out the upper edge slightly so that the clips on the
inside release. Pull the panel straight up.
●
Route the cable as illustrated, down to the floor.
R8504315
41
R8504316
42
IMG-242243
Preparations, passenger compartment
43
●
Insert a screwdriver through the hole (1) on the seat link and press in the catch.
Move the link backwards by prizing with a screwdriver between the seat runner
and the link.
IMG-242244
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 15 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Preparations, passenger compartment
44
●
Carefully prise loose and remove the panel over the joint between the door sills.
IMG-242245
Preparations, passenger compartment
45
●
Pull loose the sill molding on the front edge then straight up. Angle out the sill
molding from the B-post panel.
IMG-242246
Preparations, passenger compartment
46
●
Press the catch (1) in and remove the front seat link.
●
Remove the screw.
R8504309
Preparations, passenger compartment
47
●
Press in the catches (1) and remove the seat link as illustrated.
●
Remove the screw.
R8504310
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 16 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Preparations, passenger compartment
48
●
Fold down the backrest.
●
Remove the seat links and bolts.
●
Lift out the seat.
Caution!
Exercise care when doing this so that the trim or door panels are not damaged.
IMG-242247
Preparations, passenger compartment
49
●
Loosen the upper part of the sill moulding on the rear edge and loosen the seat
belt from the end fitting. The belt is loosened by carefully pressing with a
weatherstrip tool on the lock lug so that the seat belt releases from the end
fitting.
IMG-245600
Preparations, passenger compartment
50
●
Pull the sill molding upwards until the three clips release.
●
Angle the sill moulding out from the B-post panel.
IMG-242248
Steps 51-66 apply to cars with an accessory electronic module (AEM) installed
Removal, cable harness
51
●
Remove the right-hand side floor hatch (1) in the cargo compartment.
R8504158
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 17 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Steps 51-66 apply to cars with an accessory electronic module (AEM) installed
52
●
Remove the lower folding side panel on the right-hand side.
IMG-273225
Steps 51-66 apply to cars with an accessory electronic module (AEM) installed
53A
Illustration A
●
Remove the two screws in the bracket for the accessory electronic module
(AEM).
Illustration B
●
IMG-274168
53B
Tilt the module so that the 4-pin black connector can be disconnected.
Illustration C
●
Unplug the connector.
IMG-274169
53C
IMG-274170
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 18 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Steps 51-66 apply to cars with an accessory electronic module (AEM) installed
54
●
Remove the cable ties from around the cable harness to the accessory
electronic module (AEM) along the rear member.
●
Disconnect the ground lead.
IMG-274171
Steps 51-66 apply to cars with an accessory electronic module (AEM) installed
55
●
Remove the Rear Electronic Module (REM) by opening the lock (1) on the top of
the unit. Tip the unit forward and lift it out of the mountings (2).
R3703513
Steps 51-66 apply to cars with an accessory electronic module (AEM) installed
56
●
Press in the catch on the rear brown connector in the fuse holder in the cargo
compartment, turn the lock arm up as far as it will go and pull out the connector.
R3905101
Steps 51-66 apply to cars with an accessory electronic module (AEM) installed
57
●
Carefully prise apart the sides of the connector holder in the ends so that the
connector can pass by the retaining hooks.
●
Pull out the connector.
D3703496
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 19 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Steps 51-66 apply to cars with an accessory electronic module (AEM) installed
58
●
Remove the red (R) cable from terminal 22.
R3703512
Steps 51-66 apply to cars with an accessory electronic module (AEM) installed
59
●
Press in the catch on the gray connector on the rear of the fuse holder in the
cargo compartment. Turn the lock arm up as far as it will go and pull out the
connector.
M3904942
Steps 51-66 apply to cars with an accessory electronic module (AEM) installed
60
●
Carefully prise apart the sides of the connector holder in the ends so that the
connector can pass by the retaining hooks.
●
Pull out the connector.
M3703366
Steps 51-66 apply to cars with an accessory electronic module (AEM) installed
61
●
Remove the green (GN) cable from terminal 19 and white (W) from terminal 30 in
the connector.
●
Remove the entire cable harness and place to one side. This will not be reused.
R3703511
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 20 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Installing the cable harness
62
●
Take the new cable harness (purchased separately), marked A in the kit image
and place it behind the battery.
●
Pull the cable end with black 4-pin connector through the hole in the rear edge of
the right-hand cargo floor support, up to the accessory electronic module (AEM).
Route the other end in a corresponding way to the fuse holder on the left-hand
side.
R3603578
63A
Illustration A
●
Connect the black 4-pin connector to the accessory electronic module (AEM).
Illustration B
Illustration C
●
Reinstall the module and tighten using the two screws.
IMG-274224
63B
IMG-274225
63C
IMG-274226
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 21 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
64
●
Take five cable ties from the kit and secure the wiring harness to the existing
wiring harness as illustrated.
●
Remove the ground screw and connect the ground lead (1) of the new wiring
harness. Tighten the ground screw securely.
●
Connect the red (R) cable to terminal 22 in the brown connector which was
disconnected from the fuse holder.
●
Reinstall the connector in the holder
●
Reinstall the connector in the fuse holder.
●
Connect the green (GN) cable to terminal 19 in the gray connector that was
disconnected from the fuse holder, and the white (W) to terminal 30.
R3603579
65
R3703512
66
Note!
Make a note of the position number of the connector. The position numbers are
located on the ends of the connector and in the bottom of the electronic control
module.
●
Reinstall the connector in the holder
●
Reconnect the connector in the rear electronic control module (REM).
●
Refit the Rear Electronic Module (REM).
R3703511
Installation, parking assistance camera (PAC)
Steps 67-76 apply to cars without trailer module (TRM)
67
●
Wash off the marked surfaces on the embossing on the back edge of left rear
wheel housing using isopropanol. Wipe dry.
R3603610
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 22 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Installation, parking assistance camera (PAC)
68
●
Take a Velcro fastener and cut it off 90 mm (3 1/2") from the edge.
R3603615
Installation, parking assistance camera (PAC)
69
●
Remove the protective tape from the Velcro fasteners.
A0000335
Installation, parking assistance camera (PAC)
70
●
Attach both Velcro fasteners to the embossing as illustrated.
IMG-242249
Installation, parking assistance camera (PAC)
71
●
Clean the underneath of the parking assistance camera (PAC) using isopropanol.
IMG-242250
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 23 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Installation, parking assistance camera (PAC)
72
●
Take a Velcro fastener and cut it off 75 mm (3) from the edge.
R3603612
Installation, parking assistance camera (PAC)
73
●
Remove the protective tape from the Velcro fasteners.
R3603616
Installation, parking assistance camera (PAC)
74
●
Secure the Velcro fasteners on the control module as illustrated.
IMG-242251
Installation, parking assistance camera (PAC)
75
●
Connect the three connectors to the control module.
IMG-242252
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 24 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Installation, parking assistance camera (PAC)
76
●
Secure the control module on the newly attached Velcro fasteners. Press hard
so that sits firmly.
IMG-242253
Installation, parking assistance camera (PAC)
Steps 77-85 apply to cars with a trailer module (TRM) installed
77
●
Clean the surfaces, as illustrated, on the trailer module (TRM) using isopropanol.
IMG-242254
Installation, parking assistance camera (PAC)
78
●
Clean the underneath of the parking assistance camera (PAC) using isopropanol.
Wipe dry.
IMG-242255
Installation, parking assistance camera (PAC)
79
●
Remove the two Velcro fasteners from the kit and cut them in the middle.
IMG-222282
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 25 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Installation, parking assistance camera (PAC)
80
●
Press the Velcro pieces together.
IMG-222283
Installation, parking assistance camera (PAC)
81
●
Remove the protective film on one side of the Velcro fasteners.
IMG-222285
Installation, parking assistance camera (PAC)
82
●
Press the Velcro fasteners onto the parking assistance camera (PAC) as
illustrated.
IMG-242256
Installation, parking assistance camera (PAC)
83
●
Remove the protective film from the Velcro fasteners.
IMG-242257
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 26 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Installation, parking assistance camera (PAC)
84
●
Connect the three connectors to the control module.
IMG-242258
Installation, parking assistance camera (PAC)
85
●
Place the parking assistance camera (PAC) on the trailer module (TRM). It must
be positioned so that the modules are edge-to-edge at the rear edge.
IMG-242259
Connecting the rear electronic module (REM)
Steps 86-89 apply to cars without an accessory electronic module (AEM)
86
●
Remove the Rear Electronic Module (REM) by opening the lock (1) on the top. Tip
the module forward and lift it out of the mountings (2).
IMG-242260
Connecting the rear electronic module (REM)
87
●
Press in the catch on the rear of the grey connector, twist the locking arm up as
far as it will go and pull out the connector.
M3904942
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 27 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Connecting the rear electronic module (REM)
88
●
Carefully prise apart the sides of the connector holder in the ends so that the
connector can pass by the retaining hooks.
●
Pull out the connector.
M3703366
Connecting the rear electronic module (REM)
89
Note!
Make a note of the position number of the connector. The position numbers are located
on the ends of the connector and in the bottom of the electronic control module.
●
Connect the green (GN) cable to terminal 19 in the connector. Connect the white
(W) cable to terminal 30.
●
Reinstall the connector in the holder
●
Reconnect the connector in the rear electronic control module (REM).
●
Refit the Rear Electronic Module (REM).
R3703511
Steps 90-95 apply to cars with an accessory electronic module (AEM) installed
90
●
Connect the large black female connector in the pre-routed cable harness, to the
connector for towbar wiring in the fuse holder.
Secure the excess of the large black male connector using a cable tie from the
kit.
IMG-274233
91
●
Steps 91-92 apply to cars with a towbar
Disconnect the towbar wiring connector from the fuse holder.
IMG-274234
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 28 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
92
●
Connect the large black female connector in the pre-routed cable harness to the
fuse holder.
●
Connect the towbar wiring connector, which was disconnected from the fuse
holder to the corresponding one in the routed cable harness.
IMG-274235
93
●
Steps 93-95 apply to cars with a towbar wiring adapter
Disconnect the towbar wiring adapter's connector from the fuse holder.
IMG-274236
94
●
Connect the large black female connector in the pre-routed cable harness to the
fuse holder.
●
Connect the towbar wiring adapter's connector, which was disconnected from
the fuse holder to the corresponding one in the routed cable harness.
●
Secure the loose cables and the small fuse holder using a cable tie.
IMG-274237
95
IMG-274238
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 29 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Connection to multimedia module (MMM)
96
●
Route both adapter cables (5 way green and 12 way gray connector) along the
molding and up to the driver's seat.
IMG-242261
Connection to multimedia module (MMM)
97
●
Disconnect the two connectors on the multimedia module (MMM).
IMG-242262
Connection to multimedia module (MMM)
98
●
Connect the pre-routed adapter cables to the multimedia module (MMM) and to
respective disconnected connectors.
Note!
Route the new cables under the existing cables.
IMG-242263
Connection to multimedia module (MMM)
99
●
Place the connectors and excess wiring in the joint under the carpet.
IMG-242264
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 30 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Installation, ground strip
100
●
Insert the tool's hook between the dashboard and the louvre. Turn the tool 90°
and pull the louvre straight up.
IMG-246927
Installation, ground strip
101
●
Remove the five screws.
IMG-246928
Installation, ground strip
102
●
Applies to cars without a centrally mounted loudspeaker
Lift up the monitor unit and place it on the dashboard.
Note!
Place some protection under the monitor unit so as not to damage the
dashboard.
IMG-246929
●
Applies to cars with a centrally mounted loudspeaker
Remove the three connectors.
Installation, ground strip
103
●
Remove the M6 screw.
IMG-246930
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 31 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Installation, ground strip
104
●
Take the earth braid and foam tape bit from the kit.
●
Cut off the foam tape lengthways in two equal pieces. Cover the earth braid with
foam tape so that there is no foam tape on the cable terminals.
IMG-246933
Installation, ground strip
105
●
Fit the earth braid as illustrated. Use a new screw from the kit.
IMG-246934
Installation, ground strip
106
●
Applies to cars without a centrally mounted loudspeaker
Refit the monitor unit and at the same time guide the earth braid up through the
hole in front of the monitor.
●
Remove the left-hand screw for the monitor.
IMG-246935
Installation, ground strip
107
●
Applies to cars without a centrally mounted loudspeaker
Place the earth braid over the hole where the screw was positioned, fit the
screw and tighten the earth braid.
●
Refit the five screws for the monitor unit.
●
Refit the louvre.
IMG-246936
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 32 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Installation, ground strip
108
●
●
Steps 108-113 apply to cars with a centrally mounted loudspeaker
Remove the three screws for the monitor.
Remove the monitor by first angling it backwards at the lower edge and then
guiding it out.
IMG-248723
Installation, ground strip
109
●
Locate the end by the left-hand mounting point for the monitor on the loudspeaker
frame.
IMG-248724
Installation, ground strip
110
●
Measure and mark out two points according to the image.
IMG-248725
Installation, ground strip
111
●
Pre-drill in the centers of the markings using a Ø 2mm (5/64") diameter drill bit.
●
Then drill out the holes. Use a Ø 8mm " (5/16") drill bit.
●
Cut away the part between the drill holes as illustrated.
IMG-248726
© VolvoCar Corporation, 2007 Printed in Sweden
31260504
Page 33 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Installation, ground strip
112
●
Reinstall the monitor and tighten using two screws as illustrated.
IMG-248727
Installation, ground strip
113
●
Take the loose end of the ground strip and thread it through the drilled holes from
underneath.
●
Secure the cable terminal using the screw for the monitor and tighten.
●
Reinstall the monitor unit with its five screws.
●
Refit the louvre.
IMG-248728
Finishing work
114
●
Install:
the sill trim panels.
●
panel over the joint between the door sills.
●
seat belt.
Note!
IMG-242267
© VolvoCar Corporation, 2007 Printed in Sweden
Check that the seat belt is secure by jerking it hard in an upwards direction.
●
seat, tighten the screws to 50 Nm (36.8 lbf.ft.).
●
seat links.
●
side panels.
●
Turn the ignition key to position II.
●
Reconnect the battery negative lead
●
Refit the floor hatches.
31260504
Page 34 of 35
Installation instructions, accessories - Park Assist, camera
Volvo Car Corporation Göteborg, Sweden
Finishing work
115
●
Download the software for the accessory's function following the service
information in VIDA.
●
Check the position of the camera using the calibration program. See VIDA under
"Diagnostics/Vehicle communication/Advanced".
Note!
If the camera lens cannot be correctly positioned, remove the lens and drill out
the two holes in the tailgate for the screws. If necessary, file the rectangular
holes so that the camera lens can be adjusted to the correct position.
IMG-242268
●
© VolvoCar Corporation, 2007 Printed in Sweden
Refit the trunk lid's panels and lamp.
31260504
Page 35 of 35