TESTO 0560 0425 Instruction Manual

Testo 0560 0425 is a compact device for measuring flow velocities and temperatures using a permanently connected hot wire probe. It's ideal for tasks like volume flow measurements in ducts, measuring flow velocities in rooms, and temperature measurement of flows. The device offers a user-friendly interface with easy navigation through menus, allowing you to customize settings like units, area, and auto-off functionality. A Bluetooth connection enables wireless data transfer to the Testo Smart App for advanced analysis and report generation.

PDF Download

Document

testo 425 - Digital hot wire anemometer
0560 0425
Instruction manual
Contents
Contents
About this document ...........................................................................3
Safety and disposal..............................................................................3
Security ..................................................................................................3
Disposal .................................................................................................4
Product-specific information...............................................................5
Intended use .........................................................................................5
Product description .............................................................................6
Instrument overview ...............................................................................6
First steps .............................................................................................7
Inserting / changing batteries .................................................................7
Getting to know the product ...................................................................8
Connecting probes .................................................................................8
Switching the instrument on and off .......................................................8
Switching the display illumination on and off ..........................................8
Establishing a Bluetooth&reg; connection .....................................................9
Establishing a Bluetooth&reg; connection to the testo Smart App ..............10
Using the product...............................................................................11
Controls on the measuring instrument ..................................................11
Implementing settings ..........................................................................12
Opening configuration mode ................................................................13
Setting the unit .....................................................................................13
Setting the area ....................................................................................14
Reading absolute pressure ..................................................................14
Carrying out a reset of the setting menus .............................................14
Carrying out a reset of the measuring instrument.................................14
Measuring ............................................................................................15
Changing the measurement channel display .......................................15
Freezing a reading, displaying the maximum/minimum value ..............15
Resetting maximum/minimum values ...................................................16
Carrying out multi-point mean calculation ............................................16
Carrying out continuous mean calculation ............................................17
Printing data .........................................................................................17
Controls via testo Smart App ............................................................18
Overview of operating controls .............................................................18
Contents
App options .......................................................................................... 20
Setting the language ............................................................................ 20
Displaying App Info .............................................................................. 20
Displaying the tutorial .......................................................................... 20
Application menus ............................................................................... 21
Selecting an application menu ............................................................. 21
Setting favourites ................................................................................. 21
Displaying information about an application ........................................ 21
Making measuring instrument settings ................................................ 22
Configuring the measuring instrument menu ....................................... 24
Setting Auto Off ................................................................................... 25
Activating damping .............................................................................. 25
Setting the Correction Factor ............................................................... 26
Setting the area ................................................................................... 26
Display of the readings ........................................................................ 27
Adjusting the view ................................................................................ 27
Exporting readings ............................................................................... 28
Excel (CSV) Export .............................................................................. 29
PDF Export .......................................................................................... 29
Maintaining the product .................................................................... 30
Inserting / changing batteries ............................................................... 30
Cleaning the instrument ....................................................................... 30
Technical data for testo 425 ............................................................. 31
Tips and assistance........................................................................... 32
Questions and answers ....................................................................... 32
Accessories and spare parts ............................................................... 33
1 About this document
About this document

The instruction manual is an integral part of the instrument.

Keep this documentation to hand so that you can refer to it when necessary.

Always use the complete original instruction manual.

Please read this instruction manual through carefully and familiarize yourself
with the product before putting it to use.

Hand this instruction manual on to any subsequent users of the product.

Pay particular attention to the safety instructions and warning advice in order
to prevent injury and damage to the product.
Safety and disposal
Security
General safety instructions

Only operate the product properly, for its intended purpose, and within the
parameters specified in the technical data.

Do not apply any force.

Do not operate the instrument if there are signs of damage to the housing or
connected cables.

Dangers may also arise from objects to be measured or the measuring
environment. Always comply with the locally valid safety regulations when
carrying out measurements.

Do not store the product together with solvents.

Do not use any desiccants.

Only perform maintenance and repair work on this instrument that is
described in this documentation. Follow the prescribed steps exactly when
doing the work.

Use only original spare parts from Testo.
Batteries

Improper use of batteries may cause the batteries to be destroyed, or lead to
injury due to current surges, fire or escaping chemicals.

Only use the batteries supplied in accordance with the instructions in the
instruction manual.

Do not short-circuit the batteries.

Do not take the batteries apart and do not modify them.
3
2 Safety and disposal

Do not expose the batteries to heavy impacts, water, fire or temperatures in
excess of 60 &deg;C.

Do not store the batteries in the proximity of metal objects.

In the event of contact with battery acid: rinse affected areas thoroughly with
water, and if necessary consult a doctor.

Do not use any leaky or damaged batteries.
Warnings
Always pay attention to any information denoted by the following warnings.
Implement the precautionary measures specified!
DANGER
Risk of death!
WARNING
Indicates possible serious injury.
CAUTION
Indicates possible minor injury.
CAUTION
Indicates possible damage to equipment.
Disposal

Dispose of faulty rechargeable batteries and spent batteries in accordance
with the valid legal specifications.

At the end of its useful life, deliver the product to the separate collection
point for electric and electronic devices (observe local regulations) or return
the product to Testo for disposal.

4
WEEE Reg. No. DE 75334352
3 Product-specific information
Product-specific information

Do not carry out measurements on live components.

Do not expose handles and feed lines to temperatures in excess of 70&deg;C
unless they are expressly approved for higher temperatures. Temperature
specifications on probes/sensors refer only to the measuring range of the
sensor system.

Only open the measuring instrument if this is expressly described in the
documentation for the purposes of maintenance or servicing.
Intended use
The testo 425 is a compact instrument for measuring flow velocities and
temperatures by means of a permanently connected flow/temperature probe
(hot wire probe).
The product is designed for the following tasks/areas:

Volume flow measurements in ducts

Measuring flow velocities in rooms
 Temperature measurement of flows
The product should not be used in the following areas:

In potentially explosive atmospheres.

For diagnostic measurements in the medical field.
5
5 Product description
Product description
Instrument overview
1 Control keys
2 Display
3 Probe
4 Battery compartment
Explanation of icons
Refer to instruction manual
CAUTION
Damage to sensor possible!
- Do not touch sensor!
- Close the protective sleeve after the measurement.
6
6 First steps
First steps
Inserting / changing batteries
 The instrument is switched off.
1
Open the battery compartment (on the back of the instrument) via the
snap lock.
2
Insert or replace batteries (3 x AA
batteries).
Observe the polarity!
3
+ - +
Close the battery compartment.
When not in use for a long period: Take out the (rechargeable)
batteries.
Symbol explanation
Do not allow children under 6 years of age to play with batteries.
Do not throw batteries in the trash.
Do not charge batteries.
Do not place batteries near fire.
Batteries are recyclable.
7
6 First steps
Getting to know the product
Connecting probes
The required probes are permanently connected or integrated. It is not possible
to connect any additional sensors.
Switching the instrument on and off
Switching on
1 Press and hold down (2 sec) the On/Off key.
Measurement view is opened:
The current reading is displayed or ----- lights up if no reading is
available.
Switching off
1 Press and hold down (2 sec) the On/Off key.
The display turns off.
Switching the display illumination on and
off
 The measuring instrument is switched on.
1
Press and hold down (2 sec) the MENU/ENTER key.
The display illumination is switched on or off.
8
6 First steps
Establishing a Bluetooth&reg; connection
The instrument can be connected to the testo Smart App via
Bluetooth&reg; connection
 The measuring instrument is switched on.
enable the Bluetooth connection
To
for the first time, press and hold
&reg;
(approx. 2 sec) the ◄ key.
While the instrument is trying to
establish a Bluetooth&reg; connection,
the icon flashes on the display.
Bluetooth&reg; remains enabled until it is
disabled manually by pressing and
holding (approx. 2 sec) the ◄ key.
The measuring instrument saves the
Bluetooth&reg; setting and, depending
on the configuration, starts up with
Bluetooth&reg; enabled or disabled.
9
6 First steps
Establishing a Bluetooth&reg; connection to the
testo Smart App
To establish a connection via Bluetooth&reg;, you need a
tablet or smartphone with the Testo Smart App already
installed on it.
You can get the App for iOS instruments in the App Store
or for Android instruments in the Play Store.
Compatibility:
Requires iOS 13.0 or later/Android 8.0 or later,
requires Bluetooth&reg; 4.2.
&reg;
 Bluetooth is enabled in the measuring instrument.
1
Open the testo Smart App.
The app automatically searches for Bluetooth devices in the vicinity.
&reg;
2
In the Sensors menu, check whether the required instrument is
connected.
switch the instrument to be connected off and on again
Iftonecessary,
restart the connection module.
the testo Smart App is connected to the measuring instrument,
When
the icon appears on the measuring instrument display.
The measuring instrument automatically synchronizes its date and
time settings with the testo Smart App.
Once connected successfully, the current measured value from the
measuring instrument appears on the app screen in the Live view.
10
7 Using the product
Using the product
Controls on the measuring instrument
 The instrument is switched on.
on the smartphone and connected
 The testo Smart App is installed
&reg;
to the instrument via Bluetooth .
and controls are implemented either on the instrument or via
Settings
the app.
If the measuring instrument is connected to the testo Smart App,
settings can only be made via the app. The measuring instrument then
remains in the measurement view and other menus, e.g. Settings,
cannot be opened.
1
2
On/Off / MODE/END key
Bluetooth&reg; / ◄ key
3
Battery indicator
4
Parameter 1 unit
5
Parameter 1 measured value display
6
Parameter 2 measured value display
11
7 Using the product
7
Parameter 2 selected unit
8
Print / ► key
9
Illumination / MENU/ENTER key
Implementing settings
Selecting, opening and setting functions
1 Press the relevant key to select the functions
Secondary assignment (long press)
All keys with a grey corner have a secondary assignment, which can be
selected by pressing and holding the key for a longer time (2 sec).
Adjustable functions
Ensure correct settings: all settings are transferred immediately. There
is no Cancel function.
Function
Setting options/comments
Bluetooth&reg; (long press)
Switch the Bluetooth&reg; connection on
or off
Arrow left
Freeze reading (HOLD function),
display maximum/minimum value.
On/Off (long press)
In configuration mode:
Decrease value, select option
Switches the instrument on or off
MODE/END
Select or end multi-point or continuous
mean calculation.
Display illumination (long press)
OFF (display illumination not active) or
ON (display illumination active)
12
7 Using the product
Function
Setting options/comments
MENU/ENTER
Open configuration mode
Start continuous measurement /
record multi-point readings
(Operation also possible directly on
measuring instrument if it is connected
to the app)
Print (long press)
Arrow right
In configuration mode:
Confirm input
Output readings via external printer
Change second measurement
parameter (bottom line)
In configuration mode:
Increase value, select option
Opening configuration mode
 The instrument is switched on and is in the measurement view.
1
Press MENU/ENTER until the display changes.
The instrument is now in configuration mode.
MENU/ENTER to switch to the next function. You can leave
Press
configuration mode at any time. To do this, press MODE/END until the
instrument has changed to the measurement view. Any changes that
have already been made in configuration mode will be saved.
Setting the unit
 Configuration mode is open, “UNITS” is displayed.
1
Press ◄ / ► to choose between metric (“METR”) and imperial
(“IMPER”) units of measurement and confirm with MENU/ENTER.
2
Press ◄ / ► to set the required unit for the top line (m/s, fpm) and
confirm with MENU/ENTER.
13
7 Using the product
3
Press ◄ / ► to set the required unit for the bottom line (m3/h, l/s, cfm)
and confirm with MENU/ENTER.
Setting the area
 Configuration mode is open, “AREA” is displayed.
1
Press ◄ / ► to select whether the cross-sectional area is to be
entered in m&sup2; or in mm&sup2; and confirm with MENU/ENTER.
2
Press ◄ / ► to set the cross-sectional area and confirm with
MENU/ENTER.
Reading absolute pressure
Thanks to a built-in absolute pressure sensor (measurements are taken on the
measuring instrument, not on the probe head), no additional input of the air
density is required.
 Configuration mode is open.
1
Press ◄ / ► to scroll through the configuration menus until “P_ABS”
(absolute pressure) is displayed.
The current ambient air pressure is displayed.
Carrying out a reset of the setting menus
 Configuration mode is open, “M. RES” (menu reset) is displayed.
1
Press ◄ / ► to select the required option and confirm with
MENU/ENTER:
o
NO: Do not carry out reset.
o
YES: Carry out reset. All concealed menus that were hidden
via the testo Smart App are displayed again.
The instrument returns to measurement view.
Carrying out a reset of the measuring
instrument
 Configuration mode is open, “RESET” is displayed.
14
7 Using the product
1
Press ◄ / ► to select the required option and confirm with
MENU/ENTER:
o
NO: Do not carry out reset.
o
YES: Carry out reset. The instrument is reset to the factory
settings.
The instrument returns to measurement view.
Measuring
The instrument is switched on and is in the measurement view.
1
Position the probe.
The arrow mark on the probe head
must point in the direction of flow.
The correct measurement value is
determined by rotating the probe
slightly in both directions until the
maximum value is displayed.
2
Read the measured values on the display.
Changing the measurement channel
display
1 - Switch between the display of temperature (&deg;C, &deg;F) and calculated
volume flow (m3/h, l/s, cfm):
Press ► .
Freezing a reading, displaying the
maximum/minimum value
The current reading can be frozen. The maximum and minimum values since
the last time the instrument was switched on in the standard view or during a
multi-point or continuous measurement can be displayed.
1
Press ◄ several times until the desired value is displayed.
are displayed in turn:
Theo following
Hold: frozen measured value
o
Max: Maximum value
15
7 Using the product
o
o
Min: Minimum value
Current measuring value
Resetting maximum/minimum values
The maximum/minimum values of all channels can be reset to the current
reading.
1
Press ◄ several times until Max or Min lights up.
2
Hold down ◄ (approx. 2 s).
All maximum and minimum values are reset to the current reading.
Carrying out multi-point mean calculation
1
Press MODE/END.
 flashes.
number of readings recorded is displayed in the upper line, while
The
the current reading is displayed in the lower line.
2
To record readings (in the desired quantity):
Press MENU/ENTER (several times).
3
To end measurement and calculate the mean value:
Press MODE/END.
 and
flash.
The number of measured values and the calculated multi-point mean
value are displayed.
4
To switch back to the measuring view:
Press MODE/END.
16
7 Using the product
Carrying out continuous mean calculation
1
Press MODE/END twice.
 flashes.
elapsed measuring time (mm:ss) is displayed in the upper line,
The
while the current reading is displayed in the lower line.
2
Start measurement:
Press MENU/ENTER.
3
To interrupt/continue measurement:
Press MENU/ENTER each time.
4
To end measurement and calculate the mean value:
Press MODE/END.
 and
flash.
The measurement period and the calculated continuous mean value
are displayed.
5
To switch back to the measuring view:
Press MODE/END.
Printing data
&reg;
 A testo Bluetooth /IRDA printer (order no. 0554 0621) is connected
via Bluetooth and switched on.
When first setting up a connection between the testo measuring
instrument and the testo Bluetooth&reg;/IRDA printer, the initialization
phase can last up to 30 seconds.
1
Press and hold ► to transfer the data to the printer.
Data is printed out (LED on the printer flashes green).
17
8 Controls via testo Smart App
Controls via testo Smart App
If the measuring instrument is connected to the testo Smart App, it is primarily
operated via the app. The measuring instrument remains in the measurement
view and settings menus cannot be opened on the measuring instrument.
Overview of operating controls
1 Choice of applications
3
Display of connected measuring
instruments including readings
Measurement configuration (the
menu changes depending on the
5
measuring instrument connected
and the application selected)
18
2
Switch between the views (live,
graphic, table)
4 Start/stop
6
Configuration of the measuring
instrument
8 Controls via testo Smart App
Additional symbols on the user interface of the app (not numbered)
One level back
Exit view
Share measurement data/report
Searching
Favourite
Deleting
Further information
Display report
Multiple selection
The Main menu can be accessed via the
icon at top left. To exit the main
menu, select a menu or right-click on the guided menus. The last screen
displayed is shown.
Measure
Customer
Memory
Sensors
Settings
Help and Information
Other applications
19
8 Controls via testo Smart App
App options
Setting the language
1
Click on
2
Select Settings.
3
Select Language.
.
A selection list is displayed.

4
Select the required language.
The language is changed.

Displaying App Info
In App Info you can find the version number of the installed App.
1
Click on
2
Select Help and Information.
3
Select Instrument information.
.
The version number of the app and the ID are displayed.
Displaying the tutorial
The tutorial guides you through the first steps in operating the testo
Smart App.
1
Click on
2
Select Help and Information.
.
The tutorial is displayed. In the tutorial, swipe to display the next page.

3
20
Click X to quit the tutorial.
8 Controls via testo Smart App
Application menus
Selecting an application menu
1
Click on
.
A selection of menus for various applications is displayed.
2
Select the required application.
Your selected application is displayed.
Setting favourites
1
Click on
.
A selection of menus for various applications is displayed.
2
Select the application you want to set as a favourite.
3
Click on
.
The star is displayed in orange:
.
Displaying information about an application
1
Click on
.
A selection of applications is displayed.

2
Click on
.
The information about an application is displayed.

21
8 Controls via testo Smart App
Making measuring instrument settings
The measuring instrument is connected to the testo Smart App.
1
Click on
.
The main menu opens.
2
Click on Sensors.
The Sensors menu opens.
3
Click on the required measuring instrument.
about the model, order number, serial number and
Information
firmware version is displayed.
4
Click on the Settings tab.
- A window with settings for the respective measuring instrument

opens.
In addition to the settings that can be performed on the measuring
instrument, additional settings can also be made.
22
8 Controls via testo Smart App
5
Click on the blue text under a setting
heading to activate or disable
settings or to open an input window
to enter a specific value or select a
unit.
For details on the settings options,
see the following sub-sections.
to the measuring
Changes
instrument settings in the app are
transferred directly to the measuring
instrument. Synchronization with the
app is confirmed on the measuring
instrument via “SYNC DONE”.
23
8 Controls via testo Smart App
Configuring the measuring instrument
menu
The testo Smart App can be used to set which settings menus should be
available or hidden on the measuring instrument itself.
The Settings tab in the Sensors menu is open.

1
Activate Customization instrument
menu and click on the blue text
Change instrument menu list
under the settings heading.
The Customization instrument
menu dialogue opens.
On the measuring instrument, the
following menus can be displayed or
hidden:
o
Setting the unit
o
Area
o
Funnel factor
(testo 417 only)
24
8 Controls via testo Smart App
2
Deactivate the checkboxes for the
measuring instrument menus that
are no longer to be displayed on the
measuring instrument itself.



The menus belonging to the
deactivated entries will no longer be
displayed in the measuring
instrument menu after the next
synchronization.
These settings can be reset
via the menu reset “M.RES”
and then all settings menus
will be displayed on the
measuring instrument again.
Setting Auto Off
The Settings tab is open.
1
Enable Activate Auto-off using the slider.
measuring instrument switches off automatically if no key is
The
pressed for 10 min.
Exception: a frozen reading is shown on the display (“Hold” is
displayed).
Activating damping
If the readings fluctuate wildly, it is advisable to damp the readings.
The Settings tab is open.
1
Enable Activate damping using the slider.
2
Click on Average of the measured values.
25
8 Controls via testo Smart App
The window for Average of the measured values opens.
3
Enter a value between 2 and 20 measured values.
to the measuring instrument settings in the app are
Changes
transferred directly to the measuring instrument. Synchronization with
the app is confirmed on the measuring instrument via “SYNC DONE”.
Setting the Correction Factor
If parts of the cross-sectional area are covered (e.g. by lattice bars), this
can be corrected via the correction factor.
The correction factor indicates the proportion of free space in the crosssectional area.
For example: If 20% of the area is covered, the correction factor must
be set to 0.8 (80% free space).
The correction factor can only be set via the testo Smart App and not
directly on the measuring instrument.
The Settings tab is open.
1
Enable Correction factor using the slider.
2
Enter the value for the correction factor and confirm with OK.
The changes are transferred to the measuring instrument and

synchronization with the app is confirmed on the measuring instrument
via “SYNC DONE”.
Setting the area
The cross-sectional area of the measuring point can be set both via the
testo Smart App and directly on the measuring instrument.
The display of this setting on the measuring instrument cannot be
hidden.
The Settings tab is open.
26
1
Activate Area using the slider.
2
Enter the value for the cross-sectional area and confirm with OK.
8 Controls via testo Smart App
The changes are transferred to the measuring instrument and

synchronization with the app is confirmed on the measuring instrument
via “SYNC DONE”.
Display of the readings
The available readings can be displayed in different views.

Live view:
The readings transmitted by the measuring probes can be displayed in a live
view. Readings from all connected measuring probes are displayed.

Graphic view:
Up to four different readings can be displayed in graph format. Readings to
be displayed can be selected by tapping on a reading above the diagram.

Table view:
In the table view, all readings are displayed in sequence according to date
and time. Different readings from the individual measuring probes can be
displayed by pressing ◄ ►.
Adjusting the view
1
2
Click on
.
Select Edit view.
An overview of all measurement channels and their measurement

parameters is displayed.
3
Deselect the “check mark” to hide a measuring instrument’s
measurement channel.
4
Click ▼ to select the unit of a measurement channel.
5
Click OK to confirm the settings.
27
8 Controls via testo Smart App
Exporting readings
Export
Delete
28
Report
1
Click on
2
Select Memory.
3
Click on Select measurement.
.
8 Controls via testo Smart App
Excel (CSV) Export
1
Click on
.
A selection of export options is displayed.

2
Click on Start export.
A selection of sending/export options is displayed.

3
Select the required sending/export options.
PDF Export
1
Click on Report.
A selection window is displayed.

2
If required, activate the Create PDF with all readings button.
3
Click on Create.
For measurements, please be aware that the option Create PDF with
all readings is only possible up to 30 pages, due to the resulting file
size and number of pages. In the testo DataControl software, however,
PDF reports can be created for all measurements without any
restrictions.
A report containing all the information is created.

A selection window is displayed. The report can be sent via e-mail or

Bluetooth .
&reg;
4
Click on E-mail or Bluetooth&reg;.
The report will be sent.

29
9 Maintaining the product
Maintaining the product
Inserting / changing batteries
 The instrument is switched off.
1
Open the battery compartment (on the back of the instrument) via the
snap lock.
2
Insert or replace batteries (3 x AA
batteries).
Observe the polarity!
3
+ - +
Close the battery compartment.
When not in use for a long period: Take out the (rechargeable)
batteries.
Cleaning the instrument
1 If the housing of the instrument is dirty, clean it with a damp cloth.
Do not use any aggressive cleaning agents or solvents! Mild household
cleaning agents and soap suds may be used.
30
10 Technical data for testo 425
Technical data for testo 425

Adjustment conditions for flow probes:
Adjustment in free jet &Oslash; 350 mm, reference pressure 1013 hPa,
based on testo reference Laser Doppler Anemometer (LDA).

Low flow velocities may result in greater measurement uncertainties
during humidity and temperature measurement! The probe should
be switched on outside a duct under the following conditions:
Ambient temperature: 20&deg;C
Flow: approx. 0 m/s.
Collapse the telescope after use and do not constrict with the cable.
Start with the telescopic links closest to the handle.
Feature
Value
Measurement parameters
Storage temperature
m/s, fpm
&deg;C, &deg;F
m&sup3;/h, cfm, l/s
&plusmn;(0.03 m/s + 4% of measuring value) (0 to 20
m/s)
&plusmn;(0.5 m/s + 5% of measuring value) (20.01 to
30 m/s)
&plusmn;0.5 &deg;C
0.01 m/s
0.1 &deg;C
0 to 30 m/s
-20 to +70 &deg;C
-20 to +50 &deg;C (instrument)
-20 to +70 &deg;C (probe)
-20 to +50 &deg;C
Operating humidity
0 to 80 %RH
IP class
IP20
Level of contamination
PD2
Max. operating altitude
≤ 2000 m above sea level
Nominal output
2 W @ 4,5 V DC
Battery type
3 x 1.5 V AA battery
(included in the scope of delivery)
&gt;35 h
Accuracy
Resolution
Measuring range
Operating temperature
Battery life
31
11 Tips and assistance
Feature
Value
Dimensions
Instrument: 171 x 60 x 28 mm
Probe: 180 x &Oslash;12 mm
Cable: 1.5 m
268 g
Weight
Tips and assistance
Questions and answers
Question
Possible cause
Possible solution
is displayed (top
right on the display)
Instrument switches
itself off
Instrument battery is
almost spent
Replace instrument
battery

Auto Off function is
switched on

Switch off Auto Off
function

Remaining battery

capacity is insufficient
Change the battery.
Display responds
sluggishly
Display: ----
Display: OOOO
Display: UUUU
Display: BT Fail
Display: Print Fail
Display: Probe Fail
32
Ambient temperature is
very low
Sensor error
Increase ambient
temperature
Please contact your
dealer or Testo
Customer Service.
Permissible measuring
Keep within the
range has been
permissible measuring
exceeded
range
Permissible measuring
Keep within the
range has been
permissible measuring
undershot
range
 Check Bluetooth&reg;
Bluetooth connection
connections.
could not be established
Printout could not be
performed successfully
Probe damage

Restart measuring
instrument, restart
testo Smart App.

Check Bluetooth&reg;
connections.

Switch printer off and
then on again.
Please contact your
dealer or Testo
Customer Service.
11 Tips and assistance
Question
Possible cause
Possible solution
Display: OTA Fail
The update process
&quot;over the air&quot; of the
measuring instrument
could not be completed
successfully.
Connection to the testo
Smart App was
interrupted. Keys are
locked for 3 s.
Restart the measuring
instrument and testo
Smart App and check
the Bluetooth&reg;
connection.
Restart the measuring
instrument and testo
Smart App and check
the Bluetooth&reg;
connection.
Display: APP Lost
If we have not been able to answer your question: please contact your local
dealer or Testo Customer Service. See the back of this document or the
www.testo.com/service-contact web page for contact details.
Accessories and spare parts
Description
Order no.
Bluetooth&reg;/IRDA printer
0554 0621
For a complete list of all accessories and spare parts, please refer to the product
catalogues and brochures or visit our website www.testo.com
33
Testo SE &amp; Co. KGaA
Celsiusstr. 2
79822 Titisee-Neustadt
Germany
Phone: +49 (0)7653 681-0
E-mail: [email protected]
www.testo.com
0970 9425 en 01 - 10.2022
">

Hello! I am an AI chatbot specifically trained to assist you with the 0560 0425 Instruction Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant is out of keyboard. Please, try again later.

Key features

Hot wire probe
Flow velocity and temperature measurements
Volume flow calculation
Bluetooth connectivity
Testo Smart App integration
Multi-point and continuous mean calculation
Max/Min value recording
Data logging
Data export and printing

Frequently asked questions

Go to the configuration mode and select 'UNITS'. Then, use the ◄ / ► keys to choose between 'METR' (metric) and 'IMPER' (imperial) units and confirm with MENU/ENTER. You can then set the specific units for flow velocity and volume flow.

Yes, you can connect a testo Bluetooth®/IRDA printer (order no. 0554 0621) via Bluetooth to print your measurement data.

The correction factor is used to adjust for any obstructions in the airflow, such as lattice bars, that might affect the accuracy of the measurement. You can set the correction factor in the Testo Smart App.