Ultra Reef U50 Instruction Manual
The Ultra Reef U50 is a system designed for managing water exchange between an aquarium and its technical sump. It features a charge and discharge system, allowing you to regulate water levels within your aquarium. The U50 system also includes a T-50 drain hose for efficient water transfer and an S-25 hose for connecting to a return pump. This system is compatible with aquariums that have a 53mm glass hole for installation.
PDF
Download
Document
Advertisement
Advertisement
MANUALE ISTRUZIONI INSTRUCTIONS MANUAL BEDIENUNGSANLEITUNG U50 2020.05 1 3 2 7 6 9 4 5 8 1 3 2 7 8 6 4 5 ULTRA REEF www.ultrareef.it MANUALE ISTRUZIONI INSTALLAZIONE Italiano L’installazione dei sistemi di carico e scarico prevede la foratura della vasca Manuale originale. Sistema U40 - Foro vetro da 43 +1/-0 mm Sistema U50 - Foro vetro da 53 +1/-0 mm U-50 (Sistema in & out) Questo sistema di carico o scarico permette la gestione dell’interscambio fra un acquario e la relativa vasca tecnica. Attenzione: Eseguire il lavoro con mezzi propri potrebbe causare seri danni. Consigliamo di rivolgersi al costruttore dell’acquario per la loro realizzazione. T-50 (Tubo out) Mediante il canalino di taglio presente sui passa-vetro è possibile tagliare il filetto per permettere un’installazione su vetri con spessore inferiore a 15mm. Questo tubo è stato selezionato per convogliare l’acqua di scarico di un acquario alla sua vasca tecnica. Il trasferimento è per caduta e non in pressione. Durante il montaggio eseguite il serraggio dei tappi a mano, senza ricorrere a pinze o leve. Non siliconare o aggiungere nastro di teflon sui filetti. Le guarnizioni oring devono essere posizionate all’interno dei canalini ed aderire SUL LATO ESTERNO DELLA VASCA. S-25 (Tubo in) Questo tubo è stato selezionato per collegare il sistema di carico di un acquario alla sua pompa di risalita posizionata nella vasca tecnica. Il trasferimento è a bassa pressione, con prevalenza massima 2mt e pressione inferiore a 0.2 bar (2.9 psi). Seguite le istruzioni riportate sulle immagini per collegare il tubo. Accorciate il tubo alla giusta lunghezza. Se necessario intestate il tubo tagliando i primi centimetri Attenzione: L’utilizzo del prodotto implica la lettura, la comprensione e l’accettazione di tutte le condizioni riportate nel manuale “Sicurezza” allegato. Se non trovate detto manuale contattate immediatamente i nostri uffici! Attenzione: Prima dell’uso verificare sempre l’integrità del tubo in tutta la sua lunghezza. Dopo l’installazione del sistema, verificarne la tenuta! Risciacquate attentamente con acqua e aceto (diluito al 10%) ogni componente che andrà in contatto con l’acqua. Prodotti a base di alcool o solventi possono danneggiare l’acrilico. Attenzione: I tubi in silicone sono particolarmente morbidi, temono tagli e graffi. Stringere le fascette di ritegno con forza moderata! Attenzione: Eseguite un taglio pulito per evitare perdite d’acqua. Assicurate il tubo usando le fascette regolabili. Ricordate che le fascette in acciaio inossidabile non sono garantite contro la corrosione in atmosfera salina, pertanto controllatele periodicamente e se necessario pulitele. Attenzione: Non serrare eccessivamente le fascette, altrimenti potreste rompere tubo e porta tubo. 2 ULTRA REEF www.ultrareef.it CARICO SCARICO E’ quasi impossibile valutare la portata di un sistema di tracimazione a livello teorico al fine di stabilire il livello dell’acqua in vasca con precisione. La pompa di carico deve essere determinata in base alla capacità della vasca e del sistema di scarico. Suggeriamo una pompa compresa nel seguente intervallo: Il rumore di uno scarico non è imputabile allo scarico stesso ma al modo in cui viene alimentato e/o scaricato (Vedi figura A). Usate un tubo corrugato morbido per collegare lo scarico alla sump. Evitare l’utilizzo di tubi corrugati per uso elettrico o tubazioni per scarichi domestici. La silenziosità dello scarico è data anche dal film di alghe che si formerà al suo interno nel giro di qualche settimana. Sistema U40: Pompa da 2000 a 5000 l/h Sistema U50: Pompa da 3000 a 7000 l/h Suggeriamo di installare a valle della pompa di risalita (sulla tubazione di carico) una saracinesca/rubinetto per poter regolare il livello d’acqua in vasca. Pulite periodicamente il tubo per evitare la formazione di spugne o occlusioni che ne limitino la portata. Dopo la pulizia potrebbe temporaneamente risultare più rumoroso. L’utilizzo del prodotto implica l’accettazione di tutte le condizioni riportate nel manuale e ne sottintende la precedente lettura e totale comprensione. Dopo alcuni anni di lavoro, il tubo potrebbe irrigidirsi. Verificate la tenuta e nel caso sostituitelo. 3 ULTRA REEF www.ultrareef.it SICUREZZA GENERALE IL PRODUTTORE 1. ULTRA POMPE S.r.l. Via Goldoni 37 | CAP/ZIP 20090 Trezzano sul Naviglio (MI) | ITALY Phone ++39 (0)2.48.46.45.52 [email protected] [email protected] 2. 3. 4. 5. 6. 7. 8. 9. Questo prodotto è progettato per essere conservato ed utilizzato ad una temperatura ambientale compresa fra +10 e +35 °c. Tenere lontano da fonti di luce e calore. Proteggere dalle radiazioni solari. Lo smaltimento è a carico dell’utilizzatore. Il prodotto deve essere smaltito in luogo idoneo in base alle leggi e alle norme locali, pertanto non può essere smaltito nei rifiuti normali/casalinghi. Il prodotto è progettato per funzionare a contatto con acqua dolce e salata (salinità 35‰) ad una temperatura compresa fra 10 e 35 °c. Utilizzare il prodotto solo per il suo scopo. Decliniamo ogni responsabilità per qualunque utilizzo errato o diverso da quello specificato. Prima di avviare il prodotto verificate attentamente l'integrità di ogni sua parte. Nel caso rileviate segni di usura o crepe non avviate il prodotto e contattate immediatamente i nostri uffici. Non siete autorizzati ad eseguire riparazioni sul prodotto. Nel caso siano necessarie operazioni di revisione, riparazione o manutenzione straordinaria, contattate i nostri uffici. Al primo avvio del prodotto osservatelo per alcuni minuti. Nel caso di malfunzionamenti interrompete il suo utilizzo e contattate immediatamente i nostri uffici. Non avviare il prodotto in assenza di alcune sue parti. Qualunque perdita d’acqua e danno conseguente resta responsabilità dell’utilizzatore. L’utilizzatore deve prendere ogni ragionevole precauzione per scongiurare danni a persone, animali e oggetti. Monitorare costantemente lo stato di funzionamento dell’acquario è la prima e più importante precauzione. Non abbandonare mai l’acquario e la sua tecnica incustoditi per periodi di tempo lunghi. 4 ULTRA REEF www.ultrareef.it INSTRUCTION MANUAL INSTALLATION English The installation of charge and discharge system involves the drilling of tanks glass. Original manual. U40 System - Glass hole 43 +1/-0 mm U50 System - Glass hole 53 +1/-0 mm U-50 (In & Out system) This charge or drain system allows the management of the interchange between an aquarium and the relative technical tub. Warning: Perform work by own means may cause serious damage. We recommend you to contact the manufacturer of the aquarium for hole realization. T-50 (Out hose) To use the system on tank with glass wall thickness less than 15mm, cut the thread using the groove on the glass-pass plug thread. This hose has been select for conveying the drain water of an aquarium to its technical tank. The transfer is by fall and not under pressure. During assembly, tighten the plugs by hand, without using clamp or levers. Do not add silicon paste or Teflon tape on the threads. The O-ring gasket must be placed within the grooves and adhere ON THE OUTSIDE OF THE TANK. S-25 (In hose) This hose has been selected to connect the loading water system of an aquarium tank to its return pump positioned in the technical tank. The transfer is at low pressure, with a maximum head of 2 meters and a pressure lower than 0.2 bar (2.9 psi). Follow the instructions on the images to connect the hose. Cut it to the correct length. If necessary, prepare the hose ends by cutting the first centimetres. Warning: The use of the product involves reading, understanding and acceptance of all conditions set forth in the "Safety" manual attached. If you do not find that manual immediately, contact our office! Warning: Prior to use, always check hose integrity along its entire length. After system installation, check its watertightness! Clean thoroughly with water and vinegar (diluted to 10%) each component that will go into contact with water. Products that contains alcohol or solvents can damage the acrylic. Warning: Silicon hoses are particularly soft, they fear cuts and scratches. Tighten the retaining straps with moderate force! Warning: Make a clean cut to avoid water leaks. Secure the hose using the adjustable clamp. Please note that the stainless steel clamp are not guaranteed against corrosion in saline atmosphere, so check it periodically and if necessary clean it. Warning: Do not over tighten the clamp otherwise you could break the hose and the hose connection. 5 ULTRA REEF www.ultrareef.it CHARGE DRAIN It is almost impossible to predict flow rate of an overflow system in order to determine water level in tank with precision. The charge pump must be determined according to capacity of the tank and drain system. We suggest a pump within the following range: Discharge noise is not due to the discharge itself but by way it is flushed and/or drain (See figure A). Use only soft corrugated pipe to connect the discharge to the sump. Avoid using corrugated tubes for electrical or plumbing for domestic sewage. Discharge quietness depends by algae film that forms inside piping in a matter of weeks. U40 System: Pump from 2000 to 5000 l/h U50 System: Pump from 3000 to 7000 l/h We recommend you to install a gate valve after the pump lifts (on load pipe) to adjust water level in the tank. Periodically clean the hose to avoid sponges or occlusions that limit its flow. After cleaning, it may temporarily be noisy. After several years of work, the tube may become stiff. Check its seal and in case replace it. 6 ULTRA REEF www.ultrareef.it GENERAL SAFETY THE PRODUCER 1. ULTRA POMPE S.r.l. Via Goldoni 37 | CAP/ZIP 20090 Trezzano sul Naviglio (MI) | ITALY Phone ++39 (0)2.48.46.45.52 [email protected] [email protected] 2. 3. 4. 5. 6. 7. 8. 9. This product is designed to be stored and used at an ambient temperature between +10 and +35 ° c. Keep away from sources of heat and light. Protect from solar radiation. Disposal is responsibility of user. The product should be disposed of in a suitable place in accordance with local laws and regulations and therefore cannot be disposed in municipal waste household. The product is designed to work in contact with fresh water and salt water (salinity 35‰) at a temperature between 10 and 35 °c. Use the product only for its intended purpose. We disclaim all responsibility for any improper or incorrect use other than that specified. Before start the product, carefully check the integrity of all its parts. In case of signs of wear or cracks, do not start the product and immediately contact our office. You are not authorized to perform repairs on the product. If is necessary any repair or maintenance, please contact our offices. At startup of the product, watch it for a few minutes. In the event of a malfunction discontinue its use immediately and contact our offices. Do not start the product in absence of any of its parts. Any loss of water and consequent damage remains responsibility of the user. User must take all reasonable measures to prevent harm to people, animals and objects. Constantly check operating status of the aquarium is the first and most important precaution. Never leave the aquarium and its technic unattended for long periods of time. 7 ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Water exchange system
- Charge and discharge
- T-50 drain hose
- S-25 return pump hose
- 53mm glass hole installation
Frequently asked questions
The U50 system is designed to manage the interchange of water between an aquarium and its technical tub.
The recommended pump size is between 3000 and 7000 l/h.
The installation requires drilling a 53mm hole in your aquarium glass. It is recommended to contact the manufacturer of the aquarium for this process.
Use only soft corrugated pipe for connecting the discharge to the sump. Avoid using electrical or plumbing tubes.