Sharp | CD-ES770 | Operating instructions | Sharp CD-ES770 Operating instructions

CD-ES770(U) TINSEA095AWZZ
Thank you for purchasing this SHARP product.
To obtain the best performance from this product, please read this
manual carefully. It will guide you in operating your SHARP product.
CD-ES770 Mini Component System consisting of CD-ES770 (main unit)
and CP-ES770 (speaker system).
MINI COMPONENT SYSTEM
MODEL
CD-ES770
OPERATION MANUAL
Accessories
Please confirm that the following accessories are included.
Remote control 1 AM loop antenna 1
(RRMCGA049AWSA) (QANTL0005AWZZ)
FM antenna 1
(92LFANT1746A)
Note:
Only the above accessories are included.
04/12/21
CD-ES770(U)_FRONT.fm
TINSEA095AWZZ
1
CD-ES770
SPECIAL NOTES
Important Instruction
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols:
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
NOTE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING
FCC Regulations state that any unauthorized changes or modifications
to this equipment not expressly approved by the manufacturer could void
the user's authority to operate this equipment.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
NOTE
It is the intent of Sharp that this product be used in full compliance with
the copyright laws of the United States and that prior permission be obtained from copyright owners whenever necessary.
0210
0012
FOR YOUR RECORDS
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
0012
Caution - use of controls or adjustments or performance
of procedures other than those specified herein may result in hazardous radiation exposure.
0012
For your assistance in reporting this unit in case of loss or theft,
please record below the model number and serial number which
are located on the rear of the unit.
Please retain this information.
Model number
.......................................................
Serial number
.......................................................
Date of purchase .......................................................
Place of purchase .......................................................
0202
2
04/12/21
CD-ES770(U)1.fm
TINSEA095AWZZ
CD-ES770(U) TINSEA095AWZZ
IMPORTANT SAFETY INSTRUCTIONS
be read before the product is operated.
2 Retain Instructions - The safety and operating instructions should be
retained for future reference.
3 Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4 Follow Instructions - All operating and use instructions should be
followed.
10 Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on
a bed, sofa, rug, or other similar surface. This product should not be
placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s instructions have been
adhered to.
11 Power Sources - This product should be operated only from the type
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
of power source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product dealer or
local power company. For products intended to operate from battery
power, or other sources, refer to the operating instructions.
6 Attachments - Do not use attachments not recommended by the prod-
12 Grounding or Polarization - This product may be equipped with a
5 Cleaning - Unplug this product from the wall outlet before cleaning.
uct manufacturer as they may cause hazards.
7 Water and Moisture - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a
wet basement; or near a swimming pool; and the like.
8 Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to
a child or adult, and serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
polarized alternating-current line plug (a plug having one blade wider
than the other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
Alternate Warnings - This product is equipped with a three-wire
grounding-type plug, a plug having a third (grounding) pin. This plug
will only fit into a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose
of the grounding-type plug.
9 A product and cart combination should be moved with
13 Power-Cord Protection - Power-supply cords should be routed so
care. Quick stops, excessive force, and uneven surfaces
may cause the product and cart combination to overturn.
that they are not likely to be walked on or pinched by items placed
upon or against them.
Important Instruction
1 Read Instructions - All the safety and operating instructions should
CD-ES770
14 Protective Attachment Plug - The product is equipped with an attachment plug having overload protection. This is a safety feature. See
Instruction Manual for replacement or resetting of protective device. If
replacement of the plug is required, be sure the service technician has
used a replacement plug specified by the manufacturer that has the
same overload protection as the original plug.
3
04/12/29
CD-ES770(U)1.fm
TINSEA095AWZZ
2
CD-ES770
IMPORTANT SAFETY INSTRUCTIONS (continued)
15 Outdoor Antenna Grounding - If an outside antenna or cable system
19 Object and Liquid Entry - Never push objects of any kind into this
is connected to the product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical Code, ANSI/
NFPA 70, provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antennadischarge unit, connection to grounding electrodes, and requirements
for the grounding electrode.
product through openings as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
Important Instruction
Example of antenna grounding as per
National Electrical Code, ANSI/NFPA 70
ANTENNA LEAD IN WIRE
GROUND
CLAMP
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERV ICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELECTRICAL CODE
S2898A
P OWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
16 Lightning - For added protection for this product during a lightning
storm, or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning and
power-line surges.
17 Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits,
or where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be
fatal.
18 Overloading - Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.
20 Servicing - Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
21 Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may
result in damage and will often require extensive work by a qualified
technician to restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this
indicates a need for service.
22 Replacement Parts - When replacement parts are required, be sure
the service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
23 Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine
that the product is in proper operating condition.
24 Wall or Ceiling Mounting - The product should be mounted to a wall
or ceiling only as recommended by the manufacturer.
25 Heat - The product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
4
04/12/21
CD-ES770(U)1.fm
TINSEA095AWZZ
Contents
CD-ES770
General Information
ENERGY STAR® Program Information
Page
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Controls and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 - 9
Preparation for Use
System connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 12
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Basic Operation
General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
CD Playback
Listening to a CD (CDs) . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 - 17
Advanced CD playback . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 - 20
To comply with the ENERGY STAR® standards mentioned above,
please cancel the demonstration mode, as described on page 12.
Radio
ENERGY STAR® is a U.S. registered mark.
Tape Playback
Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 - 22
Listening to a cassette tape (TAPE 1 or TAPE 2) . . . . . . .23 - 24
Tape Recording
Recording on a cassette tape . . . . . . . . . . . . . . . . . . . . . . .24 - 26
Important Instruction
Products that have earned
the ENERGY STAR® are
designed to protect the
environment through
superior energy efficiency.
Advanced Features
Timer and sleep operation . . . . . . . . . . . . . . . . . . . . . . . . .27 - 30
Enhancing your system . . . . . . . . . . . . . . . . . . . . . . . . . . .31 - 32
References
Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 - 34
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
CONSUMER LIMITED WARRANTY . . . . . . . . . . . . . . .Back cover
5
04/12/21
CD-ES770(U)1.fm
TINSEA095AWZZ
CD-ES770
Precautions
General
Please ensure that the equipment is positioned in a well-ventilated
area and ensure that there is at least 4" (10 cm) of free space
along the sides, top and back of the equipment.
4" (10 cm)
4" (10 cm)
Hold the AC power plug by the head when
removing it from the AC outlet, as pulling
the cord can damage internal wires.
Do not remove the outer cover, as this
may result in electric shock. Refer internal service to your local SHARP service
facility.
4" (10 cm)
General Information
4" (10 cm)
Use the unit on a firm, level surface free from
vibration.
Keep the unit away from direct sunlight,
strong magnetic fields, excessive dust,
humidity and electronic/electrical equipment (home computers, facsimiles, etc.)
which generate electrical noise.
Do not place anything on top of the unit.
Do not expose the unit to moisture, to temperatures higher than
140˚F (60˚C) or to extremely low temperatures.
If your system does not work properly, disconnect the AC power
cord from the AC outlet. Plug the AC power cord back in, and then
turn on your system.
In case of an electrical storm, unplug the
unit for safety.
This unit should only be used within the range of 41˚F - 95˚F (5˚C
- 35˚C).
Warning:
The voltage used must be the same as that specified on this unit.
Using this product with a higher voltage other than that which is
specified is dangerous and may result in a fire or other type of
accident causing damage. SHARP will not be held responsible for
any damage resulting from use of this unit with a voltage other than
that which is specified.
Volume control
The sound level at a given volume setting depends on speaker
efficiency, location and various other factors. It is advisable to avoid
exposure to high volume levels, which occurs while turning the unit
on with the volume control setting up high, or while continually
listening at high volumes.
6
04/12/21
CD-ES770(U)1.fm
TINSEA095AWZZ
Controls and indicators
CD-ES770
1
13
1
2
3
4
14
15
16
5
6
7
17
18
8
20
9
10
21
19
22
11
Reference page
1. Disc Trays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2. Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3. Power On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . 14
4. CD Track Up or Fast Forward, Tape 2 Fast Forward,
Tuner Preset Up, Time Up Button . . . . . . . . . . . 15, 17, 22, 24
5. Clock/Timer Button . . . . . . . . . . . . . . . . . . . . . . . . . 15, 27, 30
6. Tuning Up Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7. Tuning Down Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8. CD Track Down or Fast Reverse, Tape 2 Rewind,
Tuner Preset Down, Time Down Button . . . . . . 15, 17, 22, 24
9. Equalizer Mode Select Button . . . . . . . . . . . . . . . . . . . . . . . 14
10. Tape 1 Cassette Compartment . . . . . . . . . . . . . . . . . . . . . . 23
11. Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
12. Game/Video Input Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
13. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 16
14. CD Direct Play Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
15. Disc Tray Open/Close Button . . . . . . . . . . . . . . . . . . . . . . . 16
16. CD Play or Repeat, Tape Play Button . . . . . . . . . . . 16, 19, 23
17. Memory/Set Button . . . . . . . . . . . . . . . . . . . 15, 20, 22, 27, 30
18. Tape 2 Record Pause Button . . . . . . . . . . . . . . . . . . . . 25, 26
19. CD or Tape Stop Button . . . . . . . . . . . . . . . . . . . . . . . . 17, 24
20. Extra Bass/Demo Mode Button . . . . . . . . . . . . . . . . . . . 12, 14
21. Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
22. Tape 2 Cassette Compartment . . . . . . . . . . . . . . . . . . . . . . 23
23. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
24. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
25. Tape (1
2) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
26. Game/Video Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
General Information
Front panel
23 24 25 26
12
7
04/12/21
CD-ES770(U)1.fm
TINSEA095AWZZ
CD-ES770
Controls and indicators (continued)
1
2 34 5
6
Display
7
8
General Information
12
9 10 11
13 14 15
Reference page
1. Disc Number Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2. CD Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3. CD Pause Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4. Memory Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5. CD Repeat Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6. CD Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7. Extra Bass Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8. Tape Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
9. FM Stereo Mode Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 21
10. Daily Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
11. FM Stereo Receiving Indicator . . . . . . . . . . . . . . . . . . . . . . 21
12. Tape 2 Record Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
13. Sleep Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
14. Timer Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
15. Timer Recording Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Rear panel
3
4
5
6
1
7
Reference page
1. Cooling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2. AC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3. FM 75 Ohms Antenna Terminal . . . . . . . . . . . . . . . . . . . . . . 11
4. FM Antenna Ground Terminal . . . . . . . . . . . . . . . . . . . . . . . 11
5. AM Loop Antenna Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6. Video Output Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7. Speaker Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Speaker system
1. Tweeter
2. Woofer
3. Super Tweeters
4. Bass Reflex Duct
5. Speaker Wire
1
3
4
2
5
2
8
04/12/21
CD-ES770(U)1.fm
TINSEA095AWZZ
CD-ES770
1
1
12
13
14
2
3
4
5
6
7
8
9
10
11
15
16
17
18
19
20
21
22
23
Reference page
1. Remote Control Transmitter . . . . . . . . . . . . . . . . . . . . . . . . 13
2. CD Clear/Dimmer Button . . . . . . . . . . . . . . . . . . . . . . . . 14, 20
3. CD Random Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 16
5. CD Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6. Tape Play Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7. Tape Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
8. CD Track Down or Fast Reverse, Tape 2 Rewind,
Tuner Preset Down, Time Down Button . . . . . . 15, 17, 22, 24
9. Equalizer Mode Select Button . . . . . . . . . . . . . . . . . . . . . . . 14
10. Extra Bass Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
11. Disc Direct Search Buttons . . . . . . . . . . . . . . . . . . . . . . . . . 18
12. Memory/Set Button . . . . . . . . . . . . . . . . . . . 15, 20, 22, 27, 30
13. Power On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . 14
14. CD Pause Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
15. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
16. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
17. CD Play or Repeat Button . . . . . . . . . . . . . . . . . . . . . . . 16, 19
18. Tape (1
2) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
19. Game/Video Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
20. Tape 2 Record Pause Button . . . . . . . . . . . . . . . . . . . . 25, 26
21. CD Track Up or Fast Forward, Tape 2 Fast Forward,
Tuner Preset Up, Time Up Button . . . . . . . . . . . 15, 17, 22, 24
22. Volume Up and Down Buttons . . . . . . . . . . . . . . . . . . . . . . 14
23. Clock/Timer Button . . . . . . . . . . . . . . . . . . . . . . . . . 15, 27, 30
General Information
Remote control
9
04/12/29
CD-ES770(U)1.fm
TINSEA095AWZZ
CD-ES770
System connections
Make sure to unplug the AC power cord before any connections.
Antenna connection (see page 11)
AM loop antenna
FM antenna
Right speaker
Preparation for Use
Left speaker
Speaker connection (see page 11)
AC outlet
(AC 120 V, 60 Hz)
AC power connection (see page 12)
10
04/12/21
CD-ES770(U)1.fm
TINSEA095AWZZ
CD-ES770(U) TINSEA095AWZZ
3
CD-ES770
Antenna connection
Speaker connection
Supplied FM antenna:
Connect the FM antenna wire to the FM 75 OHMS terminal and
position the FM antenna wire in the direction where the strongest
signal can be received.
Connect the black wire to the minus (-) terminal, and the red wire to
the plus (+) terminal.
Supplied AM loop antenna:
Connect the AM loop antenna to the AM LOOP jack. Position the
AM loop antenna for optimum reception. Place the AM loop antenna
on a shelf, etc., or attach it to a stand or a wall with screws (not
supplied).
2
Red
Note:
Placing the antenna on the unit or near the AC power cord may
cause noise pickup. Place the antenna away from the unit for better
reception.
Installing the AM loop antenna:
< Assembling >
< Attaching to the wall >
Wall
Caution:
Use speakers with an impedance of 6 ohms or more, as lower
impedance speakers can damage the unit.
Do not mistake the right and the left channels. The right speaker is the one on the right
side when you face the unit.
Do not let the bare speaker wires touch
each other.
Do not allow any objects to fall into or to be
placed in the bass reflex ducts.
Incorrect
Do not stand or sit on the speakers. You may
be injured.
Placing the speaker system
Preparation for Use
Black
The left and right speakers have individual shapes. For best performance, place the speakers according to the diagram below.
Left speaker
Right speaker
Screws (not supplied)
Note:
The speaker grilles are not removable.
11
04/12/21
CD-ES770(U)2.fm
TINSEA095AWZZ
CD-ES770
System connections (continued)
AC power connection
Demonstration mode
After checking all the connections have been made correctly, plug
the AC power cord of this unit into the AC outlet. If you plug in the unit
first, the unit will enter the demonstration mode.
The first time the unit is plugged in, the
unit will enter the demonstration mode.
You will see words scroll.
Preparation for Use
To cancel the demonstration
mode:
When the unit is in the power standby mode (demonstration mode),
press the X-BASS/DEMO button.
The unit will enter the low power
consumption mode.
AC outlet
(AC 120 V, 60 Hz)
Notes:
The unit will start the tape initialization when plugged in to the AC
outlet. During this process, an initializing sound will be heard and
the unit cannot be turned on. Wait until the process is finished.
Unplug the AC power cord from the AC outlet if the unit will not be
in use for a prolonged period of time.
To return to the demonstration mode:
When the unit is in the power stand-by mode, press the X-BASS/
DEMO button again.
Note:
When the power is on, the X-BASS/DEMO button can be used to
select the extra bass mode.
Outdoor FM antenna
Use an outdoor FM antenna if you require better reception. Consult
your dealer.
Outdoor
FM antenna
Cooling fan:
The main unit is built with a cooling fan at the rear of the unit for
improved cooling. Please do not cover the opening of the fan with
any obstacles, as this will block proper ventilation.
75 ohm
coaxial cable
Note:
When an outdoor FM antenna is used, disconnect the supplied FM
antenna wire.
12
04/12/21
CD-ES770(U)2.fm
TINSEA095AWZZ
Remote control
Use 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.
1
2
3
Open the battery cover.
Insert the batteries according to the direction indicated in
the battery compartment (back of the battery cover).
When inserting or removing the batteries, push them toward the
battery terminals.
Close the cover.
Notes concerning use:
Replace the batteries if the operating distance is reduced or if the
operation becomes erratic.
Periodically clean the transmitter on the remote control and the
sensor on the unit with a soft cloth.
Exposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit.
Keep the remote control away from moisture, heat, shock, and
vibrations.
Test of the remote control
Check the remote control after checking all the connections (see
pages 10 - 12).
Point the remote control directly at the remote sensor on the unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you
can enjoy music.
Precautions for battery use:
Replace all old batteries with new ones at the same time.
Do not mix old and new batteries.
Remove the batteries if the unit will not be used for long periods
of time. This will prevent potential damage due to battery leakage.
Caution:
Do not use rechargeable batteries (nickel-cadmium battery, etc.).
Installing the batteries incorrectly may cause the unit to
malfunction.
2
Remote sensor
Preparation for Use
Battery installation
CD-ES770
8" - 20"
(0.2 m - 6 m)
Battery removal:
Open the battery cover and pull up the battery to take out.
13
04/12/29
CD-ES770(U)2.fm
TINSEA095AWZZ
CD-ES770
General control
Volume control
Main unit operation:
When the VOLUME control is turned
clockwise, the volume will increase.
When it is turned counterclockwise, the
volume will decrease.
Remote control operation:
Press the VOLUME (+ or -) button to
increase or decrease the volume.
0 ..... 30 MAXIMUM
Bass control
Basic Operation
When the power is first turned on, the unit
will enter the extra bass mode which
emphasizes the bass frequencies, and
"X-BASS" will appear. To cancel the extra
bass mode, press the X-BASS/DEMO
(X-BASS) button.
Equalizer
When the EQUALIZER (EQUALIZER MODE) button is pressed, the
current mode setting will be displayed. To change to a different
mode, press the EQUALIZER (EQUALIZER MODE) button
repeatedly until the desired sound mode appears.
In CD/TUNER/TAPE mode
To turn the power on
Press the ON/STAND-BY button to turn the power on.
After use:
Press the ON/STAND-BY button to enter the power stand-by
mode.
FLAT
No equalization.
FLAT
No equalization.
ROCK
For rock music.
ROCK
For rock music.
CLASSIC For classical music.
POPS
Illumination light control
When the power is turned on, light illuminates around the display. To
turn on/off the light, hold down the CLEAR/DIMMER button on the
remote control more than 2 seconds.
In GAME/VIDEO mode
For pop music.
VOCAL Vocals are
enchanced.
JAZZ
For jazz.
CLASSIC For classical
music.
ACTION For action games.
SPORTS For sports games.
RACING For car racing
games.
14
04/12/21
CD-ES770(U)2.fm
TINSEA095AWZZ
Setting the clock
CD-ES770
5
Press the
or
button to adjust the hour and then
press the MEMORY/SET button.
3
Press the
or
button once to advance the time by
1 hour. Hold it down to advance continuously.
In this example, the clock is set for the 12-hour (AM 12:00) display.
1
2
3
4
Press the ON/STAND-BY button to turn the power on.
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to
select "CLOCK", and press the MEMORY/SET button.
Press the
or
button to select 12-hour or 24-hour
display and then press the MEMORY/SET button.
"AM 12:00"
"AM 0:00"
"0:00"
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
The 24-hour display will appear.
(0:00 - 23:59)
Press the
or
button to adjust the minutes and
then press the MEMORY/SET button.
Press the
or
button once to advance the time by
1 minute. Hold it down to change the time in 5-minute intervals.
To confirm the time display:
[When the unit is in the stand-by mode]
Press the CLOCK/TIMER button.
The time display will appear for about 10 seconds.
[When the power is on]
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to display the
time. The time display will appear for about 10 seconds.
Note:
The "CLOCK" will appear or time will flash to confirm the time
display when the AC power supply is restored after a power failure
or unplugging the unit. If incorrect, readjust the clock as follows.
To readjust the clock:
Perform "Setting the clock" from step 1. If the "CLOCK" is not
appear in step 3, step 4 (for selecting the 12-hour or 24-hour
display) will be skipped.
To change the 12-hour or 24-hour display:
1 Clear all the programmed contents. [Refer to "Clearing all the
memory (reset)" on page 33 for details.]
2 Perform "Setting the clock" from step 1.
Basic Operation
6
Note:
The clock can also be set with the remote control.
15
04/12/21
CD-ES770(U)2.fm
TINSEA095AWZZ
CD-ES770
Listening to a CD (CDs)
This system can also play audio CD-R and CD-RW discs, but cannot
record.
Some audio CD-R and CD-RW discs may not be playable due to the
state of the disc or the device that was used for recording.
CD playback
1
2
3
Press the ON/STAND-BY button to turn the power on.
4
Place the CD on the disc tray 1, label side up.
Be sure to place 3" (8 cm) CD in the middle of the disc trays.
Press the CD button.
Press the
1 button and within 5 seconds, press the
OPEN/CLOSE button to open the disc tray 1.
CD Playback
5" (12 cm)
5
3" (8 cm)
Press the OPEN/CLOSE button to close the disc tray 1.
Total number of tracks on
the CD whose number is
flashing
" " will appear.
Total playing time of the
CD whose number is
flashing
6
You can place discs on the trays 2 - 5 by following steps
3 - 5.
7
Press the
/
button to start playback.
CD play indicator
16
04/12/21
CD-ES770(U)2.fm
TINSEA095AWZZ
CD-ES770
Playback will begin from track 1 on the DISC 1. After that disc
finishes playing, the next disc will automatically play.
After the last track on the fifth disc is played, the CD player stops
automatically.
When there is no CD in one of the disc trays (1 - 5), the empty
tray will be skipped to the next tray with a CD.
To exchange other CDs while playing a disc:
Press one of the 1 - 5 buttons for the stopped disc and within 5
seconds, press the OPEN/CLOSE button and exchange discs.
Function
Main unit
Remote
control
Operation
Play
Press in the stop
mode.
Stop
Press in the playback
mode.
Pause
Press in the playback
mode. Press the /
button to resume playback from the paused
point.
Press in the playback
or stop mode.
If you press the button
in the stop mode,
press the / button
to start the desired
track.
Press and hold down
in the playback mode.
Release the button to
resume playback.
4
5 button and within 5 seconds,
Caution:
Do not place two CDs in one disc tray.
Do not play discs of special shapes (heart, octagon, etc). It may
cause malfunctions.
Do not push the disc tray while it is moving.
If the power fails while the tray is open, wait until the power is
restored.
If the disc tray is stopped with force, "ER-CD20" will appear on
the display for 3 seconds and the unit will not function. If this
occurs, press the ON/STAND-BY button to enter the power
stand-by mode and then turn the power on again.
If TV or radio interference occurs during CD operation, move the
unit away from the TV or radio.
If a disc is damaged, dirty, or loaded upside down, the disc will be
skipped.
Auto power on function:
When you press any of the following buttons, the unit turns on.
CD button (main unit and remote control): The unit turns on and
the "CD" function is activated.
/
button (main unit and remote control): The unit turns on
and playback of the last function starts (CD, TAPE, TUNER,
GAME/VIDEO).
Track up/
Track down
Fast forward/Fast
reverse
CD Playback
To remove the CDs:
In the stop mode, press the 1 press the OPEN/CLOSE button.
Various CD functions
Notes:
Track up/track down and fast forward/fast reverse are possible
only within individual discs.
When the end of the last track is reached during fast forward,
"END" will appear on the display and CD operation will be paused.
When the beginning of the first track is reached during fast
reverse, the unit will enter the playback mode.
17
04/12/21
CD-ES770(U)2.fm
TINSEA095AWZZ
CD-ES770
Advanced CD playback
To specify a disc to play
Direct track search
You can play a disc by specifying the disc number.
By using the direct search buttons, the desired tracks on the current
disc can be played.
1
Press one of the
1-
5 buttons to select the desired disc.
Use the direct search buttons on
the remote control to select the
desired track while playing the
selected disc.
Selected track number
Selected disc number
Within 5 seconds, press the DIRECT PLAY button on the
main unit.
CD Playback
2
The direct search buttons allow you to select up to number 9.
When selecting number 10 or more, use the "+10" button.
A. For example, to choose 13
1 Press the "+10" button once.
2 Press the "3" button.
Playback will begin from track 1 on the chosen disc.
After the last track on the chosen disc is played, the CD player
stops automatically.
Note:
If the button of the disc tray with no disc is pressed, playback will not
start and the disc indicator will go out.
To stop playback:
Press the (CD ) button.
B. For example, to choose 30
1 Press the "+10" button three times.
2 Press the "0" button.
If the direct search buttons are pressed while the disc is stopped,
press the / button to start the desired track on the current disc.
Notes:
A track number higher than the number of tracks on the disc
cannot be selected.
During random play, direct search is not possible.
18
04/12/21
CD-ES770(U)2.fm
TINSEA095AWZZ
CD-ES770
Repeat play
Random play
Repeat play can play all 5 discs, all tracks on a chosen disc, or a
programmed sequence continuously.
The tracks on the disc(s) can be played in random order automatically.
To repeat all tracks on up to 5 discs:
Press the / button twice.
To random play all tracks on up to 5 discs:
Press the RANDOM button on the remote control.
4
To repeat desired tracks:
Perform steps 1 - 6 in the "Programmed play" section on page 20
and then press the / button twice.
To cancel repeat play:
Press the / button again.
" " will go out.
To repeat all tracks on the chosen disc:
1 Press one of the 1 - 5 buttons.
2 Within 5 seconds, press the DIRECT PLAY
button twice.
To cancel repeat play:
Press the DIRECT PLAY button again.
" " will go out.
CD Playback
To cancel random play:
Press the / button.
"R" will go out.
To random play all tracks on the chosen disc:
1 Press one of the 1 - 5 buttons.
2 Within 5 seconds, press the
DIRECT PLAY button.
3 Press the RANDOM button on the
remote control.
To cancel random play:
Press the DIRECT PLAY button.
"R" will go out.
Notes:
If you press the
button during random play, you can move to
the track selected next by the random operation. On the other
hand, the
button does not allow you to move to the previous
track. The beginning of the track being played will be located.
In random play, the CD player will select and play tracks
automatically. (You cannot select the order of the tracks.)
Caution:
After performing repeat or random play, be sure to press the
button. Otherwise, the disc(s) will play continuously.
(CD )
19
04/12/21
CD-ES770(U)2.fm
TINSEA095AWZZ
CD-ES770
Advanced CD Playback (continued)
Programmed play
You can choose up to 32 selections for playback in the order you like.
1
CD Playback
2
To clear the programmed selections:
Press the CLEAR/DIMMER button on the
remote control while the "MEMORY" indicator
is flashing.
Each time the button is pressed, one track will
be cleared, beginning with the last track
programmed.
While in the stop mode, press the
MEMORY/SET (MEMORY) button
to enter the programming save
mode.
To cancel the programmed play mode:
While in the stop mode and the "MEMORY" indicator is lit, press the
CLEAR/DIMMER button on the remote control. The "MEMORY"
indicator will disappear and all the programmed contents will be
cleared.
Press one of the 1 - 5 buttons
to select the desired disc.
Selected disc number
3
Press the direct search buttons
on the remote control to select
the desired track.
Selected track number
You can also select a track by pressing the
or
button.
4
Press the MEMORY/SET (MEMORY)
button to save the track number.
5
Repeat steps 2 - 4 for other tracks. Up to 32 tracks can be
programmed.
If you make a mistake, the programmed tracks can be cleared
by pressing the CLEAR/DIMMER button.
6
Press the button.
The total number in memory will
appear.
7
Press the
/
Adding tracks to the program:
If a program has been previously stored, the "MEMORY" indicator
will be displayed. Then follow steps 1 - 6 to add tracks. The new
tracks will be stored after the last track of the original program.
To check which tracks are programmed:
While the unit is stopped in the programmed play mode, press the
or
button.
Notes:
When a disc with programmed tracks is ejected, the program is
automatically canceled.
Even if you press the ON/STAND-BY button to enter the stand-by
mode or change the function from CD to another, the programmed
selections will not be cleared.
During the program operation, random play is not possible.
During programmed play, the DIRECT PLAY buttons will not
work.
button to start playback.
20
04/12/21
CD-ES770(U)2.fm
TINSEA095AWZZ
Listening to the radio
CD-ES770
Tuning
1
2
Press the ON/STAND-BY button to turn the power on.
3
Press the TUNING (
station.
Press the TUNER (BAND) button repeatedly to select the
desired frequency band (FM or AM).
or
) button to tune in to the desired
Notes:
When radio interference occurs, auto scan tuning may stop
automatically at that point.
Auto scan tuning will skip weak signal stations.
To stop the auto tuning, press the TUNING button again.
Auto power on function:
When you press any of the following buttons, the unit turns on.
TUNER (BAND) button (main unit and remote control): The unit
turns on and the "TUNER" function is activated.
/
button (main unit and remote control): The unit turns on
and playback of the last function starts (CD, TAPE, TUNER,
GAME/VIDEO).
Radio
5
Manual tuning:
Press the TUNING button as many times as required to tune in
to the desired station.
Auto tuning:
When the TUNING button is pressed for more than 0.5
seconds, scanning will start automatically and the tuner will
stop at the first receivable broadcast station.
To receive an FM stereo transmission:
Press the TUNER (BAND) button to display the "ST" indicator.
" " will appear when an FM broadcast is in stereo.
If the FM reception is weak, press the TUNER (BAND) button to
extinguish the "ST" indicator. The reception changes to monaural,
and the sound becomes clearer.
FM stereo mode indicator
FM stereo receiving indicator
21
04/12/21
CD-ES770(U)3.fm
TINSEA095AWZZ
CD-ES770
Listening to the radio (continued)
Memorizing a station
To recall a memorized station
You can store 40 AM and FM stations in memory and recall them at
the push of a button. (Preset tuning)
Press the PRESET ( or
select the desired station.
1
2
Perform steps 1 - 3 in "Tuning" on page 21.
Press the MEMORY/SET (MEMORY) button to enter the
preset tuning saving mode.
To scan the preset stations
The stations saved in memory can be scanned automatically.
(Preset memory scan)
1
Radio
2
3
Within 30 seconds, press the PRESET ( or ) button to
select the preset channel number.
Store the stations in memory, in order, starting with preset
channel 1.
4
Within 30 seconds, press the MEMORY/SET (MEMORY)
button to store that station in memory.
) button for less than 0.5 seconds to
Press the PRESET ( or ) button for more than 0.5 seconds.
The preset number will flash and the programmed stations will be
tuned in sequentially, for 5 seconds each.
Press the PRESET ( or ) button again when the desired
station is located.
If the "MEMORY" and preset number indicators go out before
the station is memorized, repeat the operation from step 2.
5
Repeat steps 1 - 4 to set other stations, or to change a
preset station.
When a new station is stored in memory, the station previously
memorized will be erased.
Note:
The backup function protects the memorized stations for a few hours
should there be a power failure or the AC power cord disconnection.
To erase entire preset memory
1
2
Press the ON/STAND-BY button to enter the stand-by mode.
While pressing down the
button and the X-BASS/DEMO
button, press the CLOCK/TIMER button until "TUNER CL"
appears.
22
04/12/21
CD-ES770(U)3.fm
TINSEA095AWZZ
Listening to a cassette tape (TAPE 1 or TAPE 2)
Tape playback
1
2
Press the ON/STAND-BY button to turn the power on.
3
Load a cassette into the
TAPE 1 compartment or
TAPE 2 compartment with
the side to be played
facing toward you.
Open the cassette compartment by pushing the
area marked " ".
6
TAPE 1
4
Press the TAPE (1
want to listen to.
5
Press the
/
(TAPE
to start playback.
TAPE 2
2) button to select the cassette you
)
Tape Playback
Before playback:
For playback, use normal or low-noise tapes for the
best sound. (Metal or CrO tapes are not
recommended.)
Do not use C-120 tapes or poor-quality tapes, as
they may cause malfunctions.
Before loading a tape into the cassette compartment,
tighten the slack with a pen or a pencil.
CD-ES770
Tape play indicator
Auto power on function:
When you press any of the following buttons, the unit turns on.
TAPE (1 2) button (main unit and remote control): The unit
turns on and the "TAPE" function is activated.
/
button (main unit and remote control): The unit turns on
and playback of the last function starts (CD, TAPE, TUNER,
GAME/VIDEO).
23
04/12/21
CD-ES770(U)3.fm
TINSEA095AWZZ
Recording on a cassette tape
CD-ES770
Various tape functions
Tape Playback
Function
Main unit
Remote
control
Operation
Play
Press in the stop
mode.
Stop
Press in the playback,
fast forward or rewind
mode.
Fast
forward/
Rewind
(TAPE 2 only)
Press in the playback
or stop mode.
Before recording:
When recording important selections, make a preliminary test to
ensure that the desired material is properly recorded.
SHARP is not liable for damage or loss of your recording arising
from malfunction of this unit.
The volume and sound controls can be adjusted with no effect
on the recorded signal (Variable Sound Monitor).
For recording, use only normal tapes. Do not use metal or
CrO tapes.
Erase-prevention tab of cassette tapes:
When recording on a cassette tape, make sure that the eraseprevention tabs are not removed. Cassettes have removable
tabs that prevent accidental recording or erasing.
To protect the recorded sound, remove the tab after recording.
Cover the tab hole with adhesive tape to record on the tape
without the tab.
Caution:
To remove the cassette, press the (TAPE ) button, and then
open the compartment.
Before changing from one tape operation to another, press the
(TAPE ) button.
If a power failure occurs during tape operation, the tape head will
remain engaged with the tape and the cassette door will not open.
In this case, wait until the power is restored.
Side A
Tab for side B
Tab for side A
24
04/12/21
CD-ES770(U)3.fm
TINSEA095AWZZ
CD-ES770
Recording from a CD (CDs)
You can record the desired CD using the DIRECT PLAY button.
4
Press the ON/STAND-BY button to turn the power on.
Press the CD button.
Load a cassette into the TAPE 2 cassette compartment
with the side to be recorded on facing you.
Wind past the leader of the tape, on which recording cannot be
performed.
Press the
button.
Recording will be paused.
5
6
Press one of the
1-
5 buttons to select the desired disc.
Within 5 seconds, press the DIRECT PLAY button to start
recording.
Recording is started from the selected CD. When the
playback of the last track is finished or the end of the tape is
reached, the CD and the cassette will stop automatically.
CD playback will start approximately 7 seconds after the
tape starts.
Tape Recording
1
2
3
To stop recording:
Press the (TAPE ) button.
The CD and tape will stop.
25
04/12/28
CD-ES770(U)3.fm
TINSEA095AWZZ
7
CD-ES770
Recording on a cassette tape (continued)
Recording from several CDs continuously:
1 Perform steps 1 - 5 in "Recording from a CD (CDs)" on page 25.
2 Within 5 seconds, press the / (TAPE ).
To perform programmed recording:
1 Program discs and tracks. (See page 20.)
2 Press the
button.
3 Press the / (TAPE ).
Dubbing from tape to tape
You can record from TAPE 1 to TAPE 2.
1
2
Tape Recording
To stop recording:
Press the (TAPE ) button.
The CD and tape will stop.
Press the ON/STAND-BY button to turn the power on.
Load a prerecorded cassette
into the TAPE 1 cassette compartment. Insert a blank tape
into the TAPE 2 cassette compartment.
It is recommended that the recording tape is the same length as
the master tape.
Recording from the radio
3
1
2
Press the TAPE (1
the display.
4
Press the
button.
Recording will be paused.
5
Press the
3
Tune in to the desired station. (See page 21.)
Load a cassette into the TAPE 2 cassette compartment
with the side to be recorded on facing you.
Wind past the leader of the tape, on which recording cannot be
performed.
Press the
Press the
/
(TAPE
(TAPE
) button to start dubbing.
To stop dubbing:
Press the (TAPE ) button.
TAPE 1 and TAPE 2 will simultaneously stop.
button.
Recording will be paused.
4
/
2) button until "TAPE 1" appears on
) button to start recording.
To interrupt recording:
Press the
button.
To resume recording, press the
Erasing recorded tapes
1
2
/
(TAPE
) button.
To stop recording:
Press the (TAPE ) button.
Note:
If you hear a whistling noise while recording an AM station, move the
AM loop antenna.
3
4
Load the tape to be erased into the TAPE 2 cassette
compartment with the side to be erased facing toward you.
Press the TAPE (1 2) button until "TAPE 2" appears on the
display.
Press the
button.
Press the / (TAPE ) button to start erasing.
Note:
Make sure that the TAPE 1 is not in use.
26
04/12/21
CD-ES770(U)3.fm
TINSEA095AWZZ
Timer and sleep operation
CD-ES770
Timer playback:
The unit turns on and plays the desired source (CD, tuner, tape) at
the preset time.
Timer recording:
The unit turns on and starts recording from the tuner at the preset
time.
This unit has 2 types of timer: ONCE TIMER and DAILY TIMER.
Once timer play and once timer recording works for
one time only at a preset time.
For example, if you are away but want to record a program on a
radio station.
Timer playback or timer recording
Before setting timer:
Daily timer:
Daily timer play and daily timer recording works at
the same preset time everyday.
For example, set the timer as a wake up call every morning.
Using the once timer and daily timer in combination:
For example, use the once timer to record a radio program, and use
the daily timer to wake up.
1 Set the daily timer (pages 27 - 29).
2 Set the once timer (pages 27 - 29).
1 minute or more
Once timer
Daily timer
Start
Stop
Start
1 Check that the clock is set to the correct time (refer to page 15).
If it is not set, you cannot use the timer function.
2 For timer playback: Load a cassette or discs to be played.
For timer recording: Load a cassette for recording in the
cassette compartment.
1
2
3
Advanced Features
Once timer:
Press the ON/STAND-BY button to turn the power on.
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to select
"ONCE" or "DAILY", and press the MEMORY/SET button.
Stop
Note:
When the setting times for the daily timer and once timer overlap,
the once timer takes priority. Allow an interval of at least 1 minute
between operations.
Set the unit to the correct time if "ONCE" or "DAILY" does not
appear.
Continued to the next page
27
04/12/21
CD-ES770(U)3.fm
TINSEA095AWZZ
8
CD-ES770
Timer and sleep operation (continued)
4
Within 10 seconds, press the
or
button to
select "ONCE SET" or "DAILY SET", and press the
MEMORY/SET button.
5
Press the
or
button to select "PLAY" or
"REC", and press the MEMORY/SET button.
Advanced Features
White
Red
9
Switch input with the
or
button, and then
press the MEMORY/SET button.
To select the timer playback source: CD, TUNER, TAPE 1 or
TAPE 2.
To select the timer recording source: TUNER.
When you select the tuner, select a station by pressing the
or
button, and then press the MEMORY/SET
button.
If a station has not been programmed, " NO P.SET" will be
displayed and timer setting will be canceled.
10 Adjust
The illustrations show the daily timer setting.
6
Press the
or
button to adjust the hour and
then press the MEMORY/SET button.
the volume using the VOLUME control, and then
press the MEMORY/SET button.
Do not turn the volume up too high.
11 Press the ON/STAND-BY button to enter the power standby mode.
The "TIMER" indicator lights up and the unit is ready for timer
playback or timer recording.
The illustrations show the timer playback setting in the daily
timer mode.
7
Press the
or
button to adjust the minutes and
then press the MEMORY/SET button.
8
Set the time to finish as in steps 6 and 7 above.
28
04/12/21
CD-ES770(U)3.fm
TINSEA095AWZZ
CD-ES770
the preset time is reached, playback or recording
will start.
The volume will increase gradually until it reaches the preset
volume.
13 When the timer end time is reached, the system will enter
the power stand-by mode automatically.
Once timer:
The timer will be canceled.
Daily timer:
The timer will operate at the same time every day. It will
continue until the daily timer setting is canceled. Cancel the
daily timer when it is not used.
Note:
When performing timer playback or recording using another unit
connected to the GAME INPUT jacks, select "GAME" in step 9.
This unit will turn on or enter the power stand-by mode automatically,
however, the connected unit will not turn on or off.
Checking the timer setting in the timer stand-by mode:
1 Press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"ONCE" or "DAILY", and press the MEMORY/SET button.
3 Within 10 seconds, press the
or
button to select
"ONCE CAL" or "DAILY CAL", and press the MEMORY/SET
button.
The unit returns to the timer stand-by mode after displaying the
settings in order.
Canceling the timer setting in the timer stand-by mode:
1 Press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"ONCE" or "DAILY", and press the MEMORY/SET button.
3 Within 10 seconds, press the
or
button to select
"ONCE OFF" or "DAILY OFF", and press the MEMORY/SET
button.
Timer will be canceled (the setting will not be canceled).
Reusing the memorized timer setting:
The timer setting will be memorized once it is entered. To reuse the
same setting, perform the following operations.
1 Turn the power on and press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"ONCE" or "DAILY", and press the MEMORY/SET button.
3 Within 10 seconds, press the
or
button to select
"ONCE ON" or "DAILY ON", and press the MEMORY/SET button.
4 Press the ON/STAND-BY button to enter the power stand-by
mode.
Advanced Features
12 When
Note:
The timer can also be set with the remote control.
29
04/12/21
CD-ES770(U)3.fm
TINSEA095AWZZ
8
CD-ES770
Timer and sleep operation (continued)
Sleep operation
The radio, compact disc and cassette tape can all be turned off
automatically.
Advanced Features
1
2
3
4
Play back the desired sound source.
Press the CLOCK/TIMER button.
Within 10 seconds, press the
or
button to select
"SLEEP", and press the
MEMORY/SET button.
Press the
or
button to select the time.
(Maximum: 3 hours - Minimum: 1 minute)
3 hours - 5 minutes 5-minute intervals
5 minutes - 1 minute 1-minute intervals
5
6
Press the MEMORY/SET button.
"SLEEP" will appear.
The unit will enter the power stand-by mode automatically
after the preset time has elapsed.
The volume will be turned down 1 minute before the sleep
operation finishes.
To confirm the remaining sleep time:
1 While "SLEEP" is indicated, press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"SLEEP X : XX".
"X : XX" is sleep remaining time.
The remaining sleep time is displayed for about 10 seconds.
You can change the remaining sleep time while it is displayed by
pressing the MEMORY/SET button (steps 4 - 5).
To cancel the sleep operation:
Press the ON/STAND-BY button while "SLEEP" is indicated.
To cancel the sleep operation without setting the unit to the stand-by
mode, proceed as follows.
1 While "SLEEP" is indicated, press the CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
"SLEEP OFF", and press the MEMORY/SET button.
To use timer and sleep operation together
Sleep and timer playback:
For example, you can fall asleep listening to the radio and wake up
to CD in the next morning.
Sleep and timer recording:
For example, you can fall asleep listening to the CD and record
radio programs while sleeping.
1
2
Set the sleep time (see left, steps 1 - 5).
While the sleep timer is set, set the timer playback or recording
(steps 2 - 10, pages 27 - 28).
Sleep timer setting
Timer playback or
recording setting
1 minute - 3 hours
Sleep operation will
automatically stop.
End time
Desired time
Timer playback or recording
start time
Caution:
When using the cassette deck, be sure the tape length is long
enough to perform both functions. If you want to sleep and wake up
listening to a tape, and the length of the tape is shorter than the sleep
timer setting, timer playback or recording will not be possible.
30
04/12/21
CD-ES770(U)3.fm
TINSEA095AWZZ
Enhancing your system
CD-ES770
The connection cord is not included. Purchase a commercially
available cord as shown below.
GAME or VCR, DVD, etc.
Listening to playback sounds of Game, VCR,
DVD, etc.
1
Connect a video game system, VCR, DVD, etc. to the front
GAME INPUT (VIDEO, AUDIO L and R) jacks.
2
Connect a TV to the rear VIDEO OUT jack.
Switch the TV input to auxiliary.
3
4
5
Yellow
White
Yellow White Red
Red
Press the ON/STAND-BY button to turn the power on.
Press the GAME/VIDEO button.
Play the connected equipment.
You can enjoy sounds from the supplied speakers and images
on the TV.
Note:
To prevent noise interference, place the unit away from the television.
Video cable
(not supplied)
RCA cord
(not supplied)
Auto power on function:
When you press any of the following buttons, the unit turns on.
GAME/VIDEO button (main unit and remote control): The unit
turns on and the "GAME" function is activated.
/ ( ) button (main unit and remote control): The unit turns on
and playback of the last function starts (CD, TAPE, TUNER,
GAME/VIDEO).
TV
To video
input jack
Advanced Features
To the line output jacks
To record on a tape from Game, VCR etc.
Yellow
Video cable
(not supplied)
Yellow
1
Insert a cassette in the TAPE 2 cassette compartment.
2
Press the GAME/VIDEO button.
3
Press the
4
Press the
5
Play the game system, VCR, etc.
button.
/
(TAPE
) button.
31
04/12/21
CD-ES770(U)3.fm
TINSEA095AWZZ
8
Troubleshooting chart
CD-ES770
Headphones
Advanced Features
Before plugging in or unplugging the headphones, reduce the
volume.
Be sure your headphones have a 1/8" (3.5 mm) diameter plug and
impedance between 16 and 50 ohms. The recommended
impedance is 32 ohms.
Plugging in the headphones disconnects the speakers
automatically. Adjust the volume using the VOLUME control.
Many potential problems can be resolved by the owner without
calling a service technician.
If something is wrong with this product, check the following before
calling your authorized SHARP dealer or service center.
General
Symptom
Possible cause
The clock is not set to the Did a power failure occur? Reset
correct time.
the clock. (Refer to page 15.)
When a button is pressed, Set the unit to the power standthe unit does not respond.
by mode and then turn it back on.
If the unit still malfunctions, reset
it. (Refer to page 33.)
No sound is heard.
Is the volume level set to "0"?
Are the headphones connected?
Are the speaker wires
disconnected?
CD player
Symptom
Possible cause
Playback does not start.
Is the disc loaded upside down?
Playback stops in the
Does the disc satisfy the
middle or is not performed
standards?
properly.
Is the disc distorted or
scratched?
Playback sounds are
Is the unit located near excessive
skipped, or stopped in the
vibrations?
middle of a track.
Is the disc very dirty?
Has condensation formed inside
the unit?
32
04/12/21
CD-ES770(U)3.fm
TINSEA095AWZZ
CD-ES770
Tuner
Symptom
Cannot record.
Possible cause
Is the erase-prevention tab
removed?
Cannot record tracks with Is it a normal tape? (You cannot
proper sound quality.
record on a metal or CrO tape.)
Cannot erase completely.
Sound skipping.
Is there any slack?
Is the tape stretched?
Cannot hear treble.
Are the capstans, pinch rollers,
or heads dirty?
Sound fluctuation.
Cannot remove the tape.
If a power failure occurs during
playback, the heads remain
engaged with the tape. Do not
open the compartment with great
force.
Possible cause
Is the unit placed near the TV or
computer?
Is the FM antenna or AM loop
antenna placed properly? Move
the antenna away from the AC
power cord if it's located nearby.
If trouble occurs
When this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal supply
voltage due to lightning, etc.) or if it is operated incorrectly, it may
malfunction.
If such a problem occurs, do the following:
1 Set the unit to the stand-by mode and turn the power on again.
2 If the unit is not restored in the previous operation, unplug and
plug in the unit, and then turn the power on.
Note:
If neither operation above restores the unit, clear all the memory by
resetting it.
Remote control
Symptom
The remote control does
not operate.
Symptom
The radio makes unusual
noises continuously.
Possible cause
Is the AC power cord of the unit
plugged in?
Is the battery polarity correct?
Are the batteries dead?
Is the distance or angle
incorrect?
Does the remote control sensor
receive strong light?
Clearing all the memory (reset)
1
2
Press the ON/STAND-BY button to enter the power stand-by
mode.
While pressing down the
button and the X-BASS/DEMO
button, press the
PRESET
button until "CLEAR AL"
appears.
Advanced Features
Cassette deck
Caution:
This operation will erase all data stored in memory including clock,
timer settings, tuner preset, and CD program.
33
04/12/21
CD-ES770(U)3.fm
TINSEA095AWZZ
9
Maintenance
CD-ES770
Condensation
Cleaning the tape-handling parts
Sudden temperature changes, storage or operation in an extremely
humid environment may cause condensation inside the cabinet (CD
pickup, tape heads, etc.) or on the transmitter on the remote control.
Condensation can cause the unit to malfunction. If this happens,
leave the power on with no disc (or cassette) in the unit until normal
playback is possible (about 1 hour). Wipe off any condensation on
the transmitter with a soft cloth before operating the unit.
Dirty heads, capstans or pinch rollers can cause poor sound and
tape jams. Clean these parts with a cotton swab moistened with
commercial head/pinch roller cleaner or isopropyl alcohol.
When cleaning the heads, pinch rollers, etc., unplug the unit which
contains high voltages.
A
TAPE 1
B
C
B
C
Before transporting the unit
References
Remove all CDs from the unit. Make sure there is no CD in the disc
tray. Then, set the unit to the power stand-by mode. Carrying the unit
with discs left inside can damage the unit.
D
E
TAPE 2
Care of compact discs
Compact discs are fairly resistant to damage, however mistracking
can occur due to an accumulation of dirt on the disc surface. Follow
the guidelines below for maximum enjoyment from your CD
collection and player.
Do not write on either side of the disc, particularly the non-label
side from which signals are read. Do not mark this surface.
Keep your discs away from direct sunlight, heat, and excessive
moisture.
Always hold the CDs by the edges. Fingerprints, dirt, or water on
the CDs can cause noise or mistracking. If a CD is dirty or does
not play properly, clean it with a soft, dry cloth, wiping straight out
from the center, along the radius.
NO
YES
Correct
Playback head
Capstan
Pinch roller
Erase head
Recording/Playback head
After long use, the deck's heads and capstans may become
magnetized, causing poor sound. Demagnetize these parts once
every 30 hours of playing/recording time by using a commercial
tape head demagnetizer. Read the demagnetizer's instructions
carefully before use.
Cleaning the CD pickup lens
In order to ensure proper operation of the CD player, preventative
maintenance (cleaning of the laser pickup lens) should be
performed periodically. Lens cleaners are commercially available.
Contact your local CD software dealer for options.
Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth and a diluted soap
solution, then with a dry cloth.
Caution:
Do not use chemicals for cleaning (gasoline, paint thinner, etc.). It
may damage the cabinet finish.
Do not apply oil to the inside of the unit. It may cause malfunctions.
34
04/12/21
CD-ES770(U)3.fm
TINSEA095AWZZ
Specifications
As part of our policy of continuous improvement, SHARP reserves
the right to make design and specification changes for product
improvement without prior notice. The performance specification
figures indicated are nominal values of production units. There may
be some deviations from these values in individual units.
AC 120 V, 60 Hz
135 W
Width: 10-1/4" (260 mm)
Height: 13" (330 mm)
Depth: 12-7/8" (326 mm)
18.5 lbs. (8.4 kg)
Output terminals
Input terminals
FM: 87.5 - 108.0 MHz
AM: 530 - 1,720 kHz
Frequency response 50 - 14,000 Hz (normal tape)
Signal/noise ratio
55 dB (TAPE-1 playback)
50 dB (TAPE-2 recording/playback)
Wow and flutter
0.3 % (WRMS)
Speaker
Type
Amplifier
Output power
Frequency range
150 watts minimum RMS per channel into
6 ohms from 100 Hz to 20 kHz, 10% total
harmonic distortion
Speakers: 6 ohms
Headphones: 16 - 50 ohms
(recommended: 32 ohms)
Video output: 1Vp-p
Game/Auxiliary (audio signal):
500 mV/47 k ohms
Game/Video: 1Vp-p
Maximum input
power
Rated input power
Impedance
Dimensions
Weight
3-way type speaker system
Super tweeter x 2
2" (5 cm) tweeter x 1
6-1/2" (16 cm) woofer x 1
300 W
150 W
6 ohms
Width: 10-5/8" (245 mm)
Height: 13" (330 mm)
Depth: 11" (279 mm)
9.2 lbs. (4.2 kg)/each
References
Weight
Tuner
Cassette deck
General
Power source
Power consumption
Dimensions
CD-ES770
CD player
Type
Signal readout
5-disc multi-play compact disc player
Non-contact, 3-beam semiconductor laser
pickup
D/A converter
1-bit D/A converter
Frequency response 20 - 20,000 Hz
Dynamic range
90 dB (1 kHz)
35
04/12/21
CD-ES770(U)3.fm
TINSEA095AWZZ
9
z
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof
with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has
been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in
design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING
THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any
warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser.
Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the
purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event
shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone
other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states
do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
Model Specific Section
Your Product Model Number & Description:
SHARP ELECTRONICS CORPORATION
CD-ES770
Mini
Component
System
Sharp Plaza,
Mahwah,
New
Jersey 07430-2135
(Be sure to have this information available when you need service for your Product.)
Warranty Period for this Product:
One (1) year parts and labor from the date of purchase.
9906
SHARP
CORPORATION
Additional Item(s) Excluded from Warranty Coverage (if any): Non-functional accessories, supplies, and consumable items.
Where to Obtain Service:
At a Sharp Authorized Servicer located in the United States.
To find a location of the nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-BE-SHARP.
What to do to Obtain Service:
Ship prepaid or carry in your Product to a Sharp Authorized Servicer.
Be sure to have Proof of Purchase available. If you ship the Product, be sure it is insured and
packaged securely.
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP.
0005
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
SHARP CORPORATION
04/12/21
9906
CD-ES770(U)_BACK.fm
Printed in Malaysia
TINSEA095AWZZ
05A R AS 1
TINSEA095AWZZ
Download PDF