Emerson | CF921VNB01 | Owner`s manual | Emerson CF921VNB01 Owner`s manual

READ AND SAVE THESE INSTRUCTIONS
54”, 60” or 72”
Fan Blades
Not Included
AVANT ECO™
Ceiling Fan Owner's Manual
Model Numbers
CF921BS01 - Brushed Steel
CF921GES01 - Golden Espresso
CF921ORB01 - Oil Rubbed Bronze
CF921SW01 - Satin White
CF921VNB01 - Venetian Bronze
Net Weight:
16.6
Lbs.
Questions, problems, missing parts: Before returning to the store call
Emerson Electric Customer Service
8 a.m. - 6 p.m., EST, Monday-Friday
Part No. F40BP74330003
Revision: 131015
1-800-654-3545
www.emersonfans.com
Form No. BP7433-3
ETL Model No.: CF921
Table of Contents
Section
Page
8. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
9. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
10. Optional Accent Kit Installation . . . . . . . . . . . . . . . . . . .12
11. Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
12. Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-15
Ceiling Fan Limited Warranty . . . . . . . . . . . . . . . . . . . . . . .19
Section
Page
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
1. Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . .3-4
2. Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . .4
3. Ceiling Fan Assembly . . . . . . . . . . . . . . . . . . . . . . . . . .5-7
4. How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . . . .7-8
5. How to Wire Your Ceiling Fan . . . . . . . . . . . . . . . . . . . .8-9
6. Remote Control Procedures . . . . . . . . . . . . . . . . . . . .9-10
7. Programming the Receiver Operating Frequency
& High Speed Conditioning of Fan Control . . . . . . . .11
READ AND SAVE THESE INSTRUCTIONS
Safety Instructions
!
3. The outlet box and joist must be securely mounted
and capable of reliably supporting at least 50 pounds.
Use only U.L. outlet boxes listed as “Acceptable for
Fan Support of 22.7kg. (50 lbs.) or less”, and use the
mounting screws provided with the outlet box. Most
outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.
4. The downrod furnished with the fan provides the
minimum recommended floor to fan blade clearance
for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least
7 feet from the floor to prevent accidental contact with
the fan blades.
6. Follow the recommended instructions for the proper
method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed
by a licensed electrician.
WARNING: To reduce the risk of electrical shock, this
fan must be installed with an isolating wall
control/switch.
NOTE: This fan is suitable for use with solid-state speed
controls.
WARNING: To reduce the risk of fire or electrical shock,
this fan should only be used with fan speed control,
Model No. FR-7861LMG-02, manufactured by Rhine
Electric Co., Ltd.
WARNING: To avoid fire, shock or injury, do not use an
Emerson or any other brand of control not specifically
approved for this fan.
WARNING: This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use this product by Emerson
Electric Co. Substitution of parts or accessories not
designated for use with this product by Emerson could
result in personal injury or property damage.
WARNING: To reduce the risk of personal injury, do not
bend the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
NOTE: All setscrews must be checked and re-tightened
where necessary before installation.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK,
OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a. Use this unit only in a manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b. Before servicing or cleaning unit, switch power off
at service panel and lock service panel
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a warning device, such as a tag, to the
service panel.
1. Read your owner’s manual carefully and keep it for
future reference.
2. Be careful of the fan and blades when cleaning,
painting, or working near the fan. Always turn off the
power to the ceiling fan before servicing.
3. Do not put anything into the fan blades while they are
turning.
4. Do not operate reversing switch until fan blades have
come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned
off at the fuse box before wiring, and do not operate
fan without blades.
2. All wiring must be in accordance with the National
Electrical Code “ANSI/NFPA 70-2014” and Local
Electrical Codes. Use the National Electrical Code if
Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label. You should record
this data above and keep it in a safe place for future use.
2
ETL Model No.: CF921
1. Unpacking Instructions
!
PACKAGE CONTENTS
WARNING
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
Part
1-800-654-3545
!
WARNING
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal injury
or property damage.
1. Check to see that you have received the following
parts:
NOTE: If you are uncertain of part description, refer
to exploded view illustration.
Description
A
Fan Motor Assembly
1
B
Ceiling Canopy
1
C
Motor Coupling Cover
1
D
Fan Blades Flanges
5
E
Hanger Bracket
1
F
Hanger Ball/Downrod Assembly
1
G
Switch Housing Assembly
1
H
Remote Control
1
A
E
HARDWARE CONTENTS
Part
1
Description
Threaded Studs, #8-32 x 1-1/4”
Quantity
2
2
Knurled Knobs, #8-32
2
3
Lockwashers, External Tooth #8
2
4
Wire Connectors
3
5
Clevis Pin
1
6
Hairpin Clip
1
7
#10-24 x 12mm Washer Head
Blade Screws
21
16mm Flat Washers (OD)
21
8
9
#8-32 x 8mm Flat Head Screw (spare)
1
10
#8-32 x 8mm Pan Head Screw (spare)
1
11
1/4-20 x 14 Captive Screw with
Lockwasher (spare)
1
Blade Balance Kit
1
12
1
2
4
8
9
F
B
G
C
H
D
NOTE: Place the parts from the loose parts bags in
a small container to keep them from being lost. If
any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.
2. Remove the fan assembly from the protective
plastic bag. Place the fan assembly into the upper
foam pad with the top of the motor facing up.
The upper foam pad serves as a holder for the fan
during the first stages of assembly.
3
5
10
Quantity
6
11
7
12
3
emersonfans.com
Please contact 1-800-654-3545 for further assistance
ETL Model No.: CF921
1. Unpacking Instructions (continued)
This Manual Is Designed to Make it as Easy as Possible for You to Assemble,
Install, Operate and Maintain Your Ceiling Fan
Your Emerson ceiling fan comes supplied with a
Fan/Light Remote Control which consists of a receiver
mounted inside the ceiling cover of the fan motor
housing. This system allows you to regulate your ceiling
fan speed and light ON/OFF.
Tools Needed for Assembly
One Phillips head screwdriver
One 1/4” blade screwdriver
One stepladder
One wire stripper
Materials
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would be
a 3-conductor (2-wire with ground) of following size:
Installed Wire Length
Up to 50 ft.
50-100 ft.
!
WARNING
Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (page 8). If you feel
you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
Wire Size A.W.G.
14
12
2. Electrical Requirements
IMPORTANT: Your ceiling fan will not function
properly, and may be damaged, if used with any
wall dimmer switch or control other than the
Emerson Electric Fan/Light Remote Control
supplied with the fan.
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with National and Local codes and
the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
!
The outlet box must be securely anchored and capable
of withstanding a load of at least 50 pounds.
!
WARNING
WARNING
!
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable for
Fan Support of 22.7 kg. (50 lbs.) or less”, and use
screws supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are not
acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
WARNING
To avoid fire or shock, follow all wiring instructions
carefully.
Any electrical work not described in these
instructions should be done or approved by a licensed
electrician.
4
ETL Model No.: CF921
3. Ceiling Fan Assembly
1. Remove the hanger ball by loosening the setscrew in
the hanger ball until the ball falls freely down the
downrod (Figure 1). Remove the pin from the
downrod, then remove the hanger ball. Retain the pin
and hanger ball for reinstallation in Step 4.
PIN
HANGER BALL
2. Separate, untwist and unkink the two 80” motor
leads. Route the motor lead wires through the
downrod. Remove the upper setscrew from the motor
coupling. Align the clevis pin holes in the downrod
with the holes in the motor coupling. Install the clevis
pin and secure with the hairpin clip (Figure 2). The
clevis pin must go through the holes in the motor
coupling and the holes in the downrod. Be sure to
push the straight leg of the hairpin clip through the
hole near the end of the clevis pin until the curved
portion of the hairpin clip snaps around the clevis pin.
The hairpin clip must be properly installed to prevent
the clevis pin from working loose. Pull on the
downrod to make sure the clevis pin is properly
installed. Reinstall the upper setscrew in the motor
coupling. Check that the lower setscrew is tightened
securely (Figure 2).
SETSCREW
Figure 1
MOTOR
COUPLING
SETSCREW
HAIRPIN
CLIP
CLEVIS PIN
DOWNROD
CLEVIS
PIN
NOTE: The setscrews must be properly installed as
described above, or fan wobble could result.
!
DOWNROD
UPPER
SETSCREW
WARNING
CLEVIS PIN
HAIRPIN
CLIP
It is critical that the clevis pin in the motor coupling is
properly installed and the setscrews securely
tightened. Failure to verify that the pin and setscrews
are properly installed could result in the fan falling.
NOTE: If LKU100 is being assembled, see Page 12,
“Optional Accent Light Kit Installation” of
instruction procedures.
Figure 2
5
emersonfans.com
Please contact 1-800-654-3545 for further assistance
ETL Model No.: CF921
3. Ceiling Fan Assembly (continued)
3. Make sure the grommet is properly installed in the
coupling cover, then slide the coupling cover on the
downrod until it rests on the motor housing. Place the
ceiling cover over the downrod. Be sure that the
ceiling cover and the coupling cover are both
oriented correctly (Figure 3).
HANGER
BALL
CEILING
COVER
4. Reinstall the hanger ball (Figure 3) on the downrod
as follows. Route the two 80” motor leads through the
hanger ball. Position the pin through the two holes in
the downrod and align the hanger ball so the pin is
captured in the groove in the top of the hanger ball.
Pull the hanger ball up tight against the pin and
securely tighten the setscrew in the hanger ball. A
loose setscrew could create fan wobble.
!
SETSCREW
DOWNROD
PIN
COUPLING
COVER
WARNING
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened. Failure
to verify that the pin and setscrew are properly
installed could result in the fan falling.
Figure 3
SHIPPING SPACERS
AND SCREWS
5. The fan comes with black and white leads that are
80” long. Before installing fan, measure up
approximately 6 to 9-inches above top of hanger
ball/downrod assembly. Cut off excess leads and
strip back insulation 1/2-inch from end of leads.
6. Carefully turn the partially assembled ceiling fan over
and set it on the shipping styrofoam for blade
installation.
SWITCH HOUSING
MOUNTING PLATE SCREW (4)
7. Remove the shipping spacers and the spacer
attachment screws from the motor before installation
of blade assemblies. Discard the spacers and spacer
screws (Figure 4).
Figure 4
#10-24 x 12mm WASHER
HEAD BLADE SCREW (4)
8. Mount blade flanges to fan blades (sold separately)
using four #10-24 x 12mm washer head blade
screws and four 16mm flat washers (Figure 5).
NOTE: Some accessory blades available are
supplied with shorter screws. These shorter screws
MUST be used to assemble the blades to flanges.
FAN BLADE
FLAT WASHER
16 mm OD
(4 per blade/flange)
BLADE
FLANGE
Figure 5
NOTE: Take care not to scratch fan housing when
installing blades.
CAPTIVE SCREW
NOTE: Remove and discard the four shipping
spacers and screws from the motor hub.
LOCKWASHER
9. Loosely attach one blade assembly to the motor hub
using the two 1/4-20 x 14 captive screws with
lockwashers. Make sure the screws are NOT
tightened. (Figure 6.) Repeat this procedure for other
four blade assemblies.
SWITCH HOUSING
MOUNTING PLATE HOLE
Figure 6
6
BLADE FLANGE
ASSEMBLY
ETL Model No.: CF921
3. Ceiling Fan Assembly (continued)
10. The blade flanges have an interlocking feature that
must be fully engaged before tightening the screw.
Make sure all the flanges are properly engaged and
then tighten the flange screws. If one of the flanges
does not seat properly on the motor hub, loosen the
adjacent flange screws, re-engage and reseat the
flanges, then tighten the screws again.
SWITCH
HOUSING
ASSEMBLY
11. Remove the four switch housing mounting screws
(Figure 7) from the switch housing plate. Position
the switch housing assembly on the switch housing
plate and align the holes in the switch housing
assembly with the holes in the plate. Secure the
switch housing assembly by installing the four
screws (Figure 7).
MOUNTING
SCREWS (4)
Figure 7
NOTE: Tuck in both the blue and white wires
carefully under the switch housing cover
!
12. You have now completed the assembly of your new
ceiling fan. You can now proceed with hanging and
wiring your fan.
WARNING
To reduce the risk of personal injury, do not bend the
blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
Please call Emerson technical support at
1-800-654-3545 if you have any questions
about installation and operation of this ceiling fan.
4. How to Hang Your Ceiling Fan
!
CEILING
WARNING
The fan must be hung with at least 7' of clearance from
floor to blades (Figure 8).
!
WARNING
AT LEAST
7'
The outlet box and joist must be securely mounted and
capable of supporting at least 50 lbs. Use only a U.L.
outlet box listed as “Acceptable for Fan Support of
22.7kg. (50 lbs.) or less”.
FLOOR
Figure 8
!
WARNING
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable for
Fan Support of 22.7kg. (50 lbs.) or less”, and use
screws supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are not
acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
NOTE: CEILING COVER
OMITTED FOR CLARITY.
OUTLET
BOX
TWO SCREWS
SUPPLIED WITH
OUTLET BOX
1. Securely attach the hanger bracket to the outlet box
using the two screws supplied with the outlet box.
(Figure 9.)
TAB
Figure 9
7
HANGER
BRACKET
emersonfans.com
Please contact 1-800-654-3545 for further assistance
ETL Model No.: CF921
4. How to Hang Your Ceiling Fan (continued)
!
WARNING
NOTE: CEILING COVER, SUPPLY WIRES AND
FAN WIRES OMITTED FOR CLARITY.
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
OUTLET
BOX
2. Carefully lift the fan and seat the hanger ball/
downrod assembly on the hanger bracket that was
just attached to the outlet box (Figure 9). Be sure the
groove in the ball is lined up with tab on the hanger
bracket (Figure 10).
HANGER
BRACKET
HANGER BALL/
DOWNROD
ASSEMBLY
Figure 10
!
WARNING
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
!
WARNING
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.
5. How to Wire Your Ceiling Fan
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
!
GROUND
WIRE
WARNING
BLACK
FAN WIRE
LISTED WIRE
CONNECTOR (3)
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advice, as it must be
grounded for safe operation.
GREEN WIRE
(GROUND) FROM
HANGER BRACKET
1. Connect the green grounding lead from the hanger
ball and the green grounding lead from the hanger
bracket to the grounding conductor of supply (this
may be a bare wire or wire with green colored
insulation). Securely connect wires with wire
connectors supplied.
GREEN WIRE
(GROUND) FROM
HANGER BALL
Figure 11
WHITE SUPPLY
(NEUTRAL)
WHITE FAN WIRE
BLACK SUPPLY
(HOT)
NOTE: CEILING COVER
OMITTED FOR CLARITY.
2. Securely connect the fan motor white wire to the
supply white (neutral) wire using wire connector
supplied (Figure 11). Securely connect the fan motor
black wire to the supply black (hot) wire using wire
connector supplied (Figure 11). After connections
have been made, turn leads upward and carefully
push leads into the outlet box, with the white and
green leads on one side of the outlet box and the
black leads on the other side of the outlet box.
NOTE: If you are using an Emerson Light Fixture
with your fan, see Light Fixture Owner’s Manual for
wiring.
8
ETL Model No.: CF921
5. How to Wire Your Ceiling Fan (continued)
!
WARNING
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
CEILING
COVER
THREADED
STUDS (2)
3. Screw the two threaded studs (supplied) into the
tapped holes in the hanger bracket.
LOCKWASHERS
(2)
4. Lift the ceiling cover up to the threaded studs and
turn until studs protrude through the holes in the
ceiling cover (Figure 12).
KNURLED
KNOBS (2)
Figure 12
5. Secure the ceiling cover in place by sliding
lockwashers over the threaded studs and installing
the two knurled knobs (supplied). (Figure 12).
Tighten the knurled knobs securely until the ceiling
cover fits snugly against the ceiling and the hole in
the ceiling cover is clear of the downrod. Your fan is
now wired to be turned on and off from the fan
switch.
!
WARNING
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box and
not pinched between the ceiling cover and the ceiling.
6. Remote Control Procedures
Your Emerson Ceiling Fan/Light SR600 Remote Control
consists of hand-held transmitter and a receiver which is
mounted under the fan ceiling cover. The remote control
is designed to separately control your ceiling fan speed,
airflow direction and light intensity.
Installation of Battery
1. Remove the battery cover by pressing firmly below
the arrow and sliding the cover off the control
(Figure 13).
2. Install two AAA alkaline batteries and reinstall the
battery cover.
The remote control transmitter is powered by two AAA
alkaline batteries (included). To prevent possible
damage if the batteries should leak, be sure to remove
the batteries when the control is not to be used for an
extended period of time.
REMOTE
CONTROL
LEVERS
Code switches in the transmitter and receiver may be
set in 32 different positions. If your fan and light go on
and off without using your control, you may be getting
interference from other remote units such as garage
door openers, car alarms or security systems. To
remedy this situations, simply change the combination
code in your transmitter and follow procedures for
Setting Operating Frequency of Remote Control.
ON
1
2
3
4 5
I
TWO AAA
BATTERIES
Preset Memory Feature
CODE
SWITCHES
Your Emerson receiver is equipped with a preset
memory feature. If the AC supply to the receiver is
powered through a wall switch, when the switch is
turned OFF, the control will remember the light intensity
and fan speed. When the switch is turned back ON the
light and fan will resume operation as they were prior to
the switch being turned OFF.
BATTERY
COMPARTMENT
COVER
SR600 REMOTE CONTROL
Figure 13
9
emersonfans.com
Please contact 1-800-654-3545 for further assistance
ETL Model No.: CF921
6. Remote Control Procedures (continued)
Your remote control has code switches which must be
set in one of 32 possible code combinations. The five
levers (numbered 1, 2, 3, 4, and 5) on the switches are
factory-set in the ON (up) positron. Change the switch
settings as follows (Figure 14).
1. Slide the five switch levers in the remote control to
your choice of ON (up) or down positions. Use a ballpoint pen or small screwdriver and slide the levers
firmly up and down.
2. The sixth switch marked ON and I is for dimming
controls of lights (if accessory light is installed).
Set switch to ON to allow for dimming of lights.
Set switch I for no dimming of lights such as
fluorescent bulbs and non-dimming CFLs.
!
WARNING
Fan installation must be completed, including the
installation of the fan blades, before testing the
remote control.
Figure 14
Your SR600 Fan/Light remote control (Figure 14) has
full control of your fan speed, air flow direction and light
intensity.
Installation of Storage Bracket for
SR600 Remote Control
A storage bracket is provided for holding your remote
control when not in use. If you desire to use the
bracket, install it on a wall that is away from excess
heat or humidity (Figure 15)
1. If airflow is desired in the opposite direction, press
the ( ) button on the wall control. The fan must be
operating at any speed for the reverse button to
function. The blades will turn in the opposite direction
and reverse the airflow.
2. To set the desired fan speed, press the ( ) button to
decrease the speed and the (
) to increase the
speed. The LED display will light up to indicate the
new speed selected.
TO INSTALL BRACKET TO WALL:
SLIDE THE COVER UP TO EXPOSE THE
SCREW HOLES FOR INSTALLATION
3. To turn the downlight on, press and release the
( ) button. The light will turn on at the light intensity
previously selected.
COVER
4. To turn the uplight on, press and release the (
)
button. The light will turn on at the light intensity
previously selected.
WALL
BRACKET
5. To vary the intensity of the light, hold the DN or UP
button down until the desired light intensity is
reached, then release the button.
SCREW
HOLES (2)
6. The sixth switch marked ON and I is for dimming
control of lights: Set switch to ON to allow for
dimming of the lights. Set switch to I for no dimming
of the lights such as for fluorescent bulbs.
Figure 15
10
ETL Model No.: CF921
7. Programming the Receiver Operating Frequency
& High Speed Conditioning of Fan Control
IMPORTANT: Ceiling fan blades MUST be
installed before high speed conditioning can
begin.
IMPORTANT: Do not interrupt the
conditioning until the fan comes to a
complete stop in approximately 5 minutes.
All functions of the control will be rejected
during conditioning.
1. Within 1 minute of restoring electricity to the ceiling
fan, push and hold the fan OFF button ( ) for 3 to 5
seconds to set the code in the receiver. The ceiling
fan lights (if installed) will blink to indicate the
transmitted has been paired with the receiver.
3. High speed conditioning is now complete.
4. If programming is unsuccessful, retry the above
instructions after cycling the wall control ON/OFF
switch to restart the 1 minute programming time
period.
IMPORTANT: Immediately after successful
pairing, the ceiling fan will automatically
begin high speed conditioning of the motor.
During conditioning, the electronic motor
control software is calculating speeds for the
2nd through 5th speed settings based on the
blades that were installed on the fan.
5. If still unsuccessful, shut off the electricity at the fuse
box or breaker panel and change the control
frequency (page 9). After changing the frequency
settings, repeat instruction #1 of this section within
one minute of restoring the electricity.
2. The fan will run for approximately 2 minutes in the
upward direction then reverse direction to down flow
and run an additional 2 minutes. When conditioning
is complete, the fan will come to complete stop.
8. Maintenance
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
!
WARNING
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth to
avoid scratching the finish.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
9. Accessories
1. Ceiling Fan Light Kits (see store or catalog).
!
WARNING
2. Ceiling Fan/Light Controls (see store or catalog).
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal injury
or property damage.
3. Downrod Extension Kits (see store or catalog).
4. Ceiling Fan Blades (see store or catalog).
!
WARNING
The use of any other control not specifically approved
for this fan could result in fire, shock and personal
injury.
11
emersonfans.com
Please contact 1-800-654-3545 for further assistance
ETL Model No.: CF921
10. Optional Accent Kit Installation
CAUTION: To reduce the risk of electric shock,
disconnect the electrical supply circuit to the fan
before installing light kit assembly.
COUPLING COVER
SCREWS (3)
1. Remove the three coupling cover screws and slide
the coupling cover up the downrod for installation of
light kit assembly (Figure 16). Retain the three
screws for later installation of coupling cover.
(RETAIN FOR LATER
INSTALLATION)
COUPLING
COVER
UPPER FAN
MOTOR
ASSEMBLY
2. Position the light kit assembly so that the opening of
the light kit assembly slides through the downrod.
Align the mounting holes of the light kit assembly to
the motor assembly (Figure 17).
NOTE: Be sure the light kit assembly connector is
located close to the motor assembly connector for
ease of installation.
Figure 16
3. Install the light kit assembly to the motor assembly
using three light kit assembly mounting screws
(Figure 17).
LIGHT KIT
ASSEMBLY
LIGHT KIT
ASSEMBLY
SCREW (3)
4. Securely connect the light kit assembly connector to
the motor assembly connector (Figure 18).
UPPER FAN
MOTOR
ASSEMBLY
5. Screw the four 25-watt candelabra base bulbs
(supplied) into the light kit assembly sockets
(Figure 18).
!
WARNING
To avoid possible fire hazard, do not exceed four 25-watt
candelabra base light bulbs.
Figure 17
6. Carefully tuck all wiring and wire connectors close to
the downrod and slide the coupling cover over the
wires.
FAN MOTOR ASSEMBLY
CONNECTOR
LIGHT KIT ASSEMBLY
CONNECTOR
NOTE: Be sure light kit assembly wires are
positioned in the dimpled wireway of the upper
housing to avoid pinching of the wires during
installation of coupling cover.
CAUTION: Before installing and tightening the
screws, be sure there are no wires pinched
between the light kit assembly/motor assembly and
coupling cover.
25-WATT
CANDELABRA
BULB (4)
Figure 18
7. Reinstall the three coupling cover screws to secure
the coupling cover (Figure 19).
COUPLING COVER
REINSTALL
COUPLING COVER
SCREWS (3)
Figure 19
12
ETL Model No.: CF921
11. Trouble Shooting
!
WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE
TROUBLE SHOOTING YOUR FAN.
TROUBLE
1. Fan will not start.
2. Fan sounds
noisy.
PROBABLE CAUSE
SUGGESTED REMEDY
1. Fuse or circuit breaker blown.
1. Check main and branch circuit fuses or circuit
breakers.
2. Loose power line connections to the fan,
or loose switch wire connections in the
switch housing.
2. Check line wire connections to fan and switch
wire connections in the switch housing.
WARNING: Make sure main power is
turned OFF.
3. Dead battery in remote control transmitter.
4. Code switches in remote control receiver
and transmitter are not in same positions.
3. Replace battery (red indicator light on transmitter
should light when any button is pressed).
4. Check that code switches are in same positions.
Reset if necessary.
1. Blades not attached to fan.
1. Attach blades to fan before operating.
2. Loose screws in motor housing.
2. Check to make sure all screws in motor housing
are snug (not over-tight).
3. Screws securing fan blade flanges to
motor hub are loose.
3. Check to make sure the screws which attach
the fan flanges to the motor hub are tight.
4. Wire connectors inside switch housing
rattling.
4. Check to make sure wire connectors in switch
housing are not rattling against each other or
against the interior wall of the switch housing.
!
!
3. Fan wobbles
excessively.
WARNING: Make sure main power is
turned OFF.
5. Screws holding blades to flanges
are loose.
5. Tighten screws securely.
1. Setscrew in motor coupling is loose.
1. Tighten both setscrews securely in the motor
coupling.
2. Setscrew in hanger ball/downrod
assembly is loose.
2. Tighten the setscrew in the hanger ball/
downrod assembly.
3. Screws securing fan blade flanges to
motor are loose.
3. Check to be sure screws which attach the fan
blade flanges to the motor are tight.
4. Fan blade flanges not seated properly.
4. Check to be sure the fan blade flanges seat
firmly and uniformly to the surface of the motor.
If flanges are seated incorrectly, loosen the
flange screws and retighten according to the
procedure in the section on "Ceiling Fan
Assembly”.
5. Hanger bracket and/or ceiling outlet
box is not securely fastened.
5. Tighten the hanger bracket screws to the outlet
box, and/or secure outlet box.
6. Fan blades out of balance.
6. Interchanging an adjacent (side-by-side) blade
pair can redistribute the weight and result in
smoother operation.
13
emersonfans.com
Please contact 1-800-654-3545 for further assistance
ETL Model No.: CF921
INSTRUCTION TO THE USER (if device contains a digital device)
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a class B computing device, pursuant to FCC
Rules. In order to maintain compliance with FCC regulations, shielded cables must be used with this
equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to
radio and TV reception. The user is cautioned that changes and modifications made to the equipment without
the approval of manufacturer could void the user’s authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
14
ETL Model No.: CF921
Notes
15
emersonfans.com
Please contact 1-800-654-3545 for further assistance
ETL Model No.: CF921
12. Repair Parts
1
2
7
3
15
4
16
8
9
14
17
6
21
5
20
10
11
BLADES SOLD
SEPARATELY
19
18
12
13
16
ETL Model No.: CF921
12. Repair Parts Listing
Key
No.
*
Model Numbers
Description
CF921BS01 CF921GES01 CF921ORB01 CF921SW01 CF921VBN01
Hanger Ball Assembly,
761655-17
761655-35
761655-32
761655-92
761655-89
—
—
—
—
—
Consisting of:
1
Hanger Bracket
2
Hanger Ball
—
—
—
—
—
3
Downrod (4.5”)
—
—
—
—
—
*
Parts Bag Containing:
764124-1
764124
764124
764124-1
764124
4
Wire Connector (3)
—
—
—
—
—
5
Pin, Clevis (1)
—
—
—
—
—
6
Clip, Hairpin (1)
—
—
—
—
—
7
Threaded Stud, #8-32 x 1-1/4” (2)
—
—
—
—
—
8
Lockwasher, External Tooth #8 (2)
—
—
—
—
—
9
Knurled Knob, #8-32 (2)
—
—
—
—
—
10
Screw, Washer Head,
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
#10-24 x 12mm (21)
11
Flat Washer 16mm OD (21)
12
Screw, Pan Head, 1/4-20 x 14mm with
Lockwasher (1)
13
Screw, Flat Head, #8-32 x 8mm (1)
—
—
—
—
—
14
Screw, Pan Head, #8-32 x 8mm (1)
—
—
—
—
—
15
Balancing Kit (1)
—
—
—
—
—
16
Canopy, Ceiling (1)
761620-BS 761620-GES 761620-ORB
761620-SW 761620-VNB
17
Motor Coupling Cover (1)
764118-BS 764118-GES 764118-ORB
764118-SW 764118-VNB
18
Switch Housing (1)
764116-BS 764116-GES 764116-ORB
764116-SW 764116-VNB
19
Flange Assembly (set of 5)
764134-BS 764134-GES 764134-ORB
764134-SW 764134-VNB
20
Motor Control, Receiver
21
Control, Transmitter SR600 Remote
—
Owner's Manual
764125-1
764125-1
764125-1
764125-1
764125-1
SR600
SR600
SR600
SR600
SR600
BP7433-3
BP7433-3
BP7433-3
BP7433-3
BP7433-3
Before discarding packaging material, be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:
• PART NUMBER
• PART DESCRIPTION
• NAME OF ITEM
• MODEL NUMBER
The model number of your Fan will be found on a label attached to the top housing.
For repair parts, phone 1-800-654-3545.
17
emersonfans.com
Please contact 1-800-654-3545 for further assistance
ETL Model No.: CF921
Notes
18
ETL Model No.: CF921
Emerson Air Comfort Ceiling Fan Limited Warranty
What The Limited Warranty Covers:
This limited warranty is offered by Air Comfort Products division of Emerson Electric Co. ("Emerson" "we" or "us") located at the address stated below to the original
retail purchaser ("you" or "your") of an Emerson Air Comfort Ceiling Fan product ("Emerson Ceiling Fan") and covers the motor and the other components and
accessories of the Emerson Ceiling Fan against all defects in workmanship and materials.
What The Period Of Coverage Is:
This limited warranty will cover the Emerson Ceiling Fan motor for the expected lifetime of your Emerson Ceiling Fan (when operated in accordance with your Owner's
Manual or other instructions provided by Emerson to you with the Emerson Ceiling Fan). All other components and accessories of the Emerson Ceiling Fan are covered
by this limited warranty for a period of one (1) year from its date of original retail purchase. ANY IMPLIED WARRANTY, INCLUDING WITHOUT LIMITATION, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THAT IS AVAILABLE TO YOU UNDER THE LAWS OF YOUR STATE OR
PROVINCE SHALL COVER THE MOTOR FOR THE EXPECTED LIFETIME OF THE MOTOR (SUBJECT TO PROPER USE), AND FOR ONE YEAR WITH RESPECT TO
COMPONENTS AND ACCESSORIES.
No Other Express or Implied Warranty Applies:
THE LIMITED WARRANTIES PROVIDED ABOVE ARE THE SOLE AND EXCLUSIVE WARRANTIES PROVIDED BY EMERSON TO YOU FOR YOUR EMERSON CEILING
FAN, AND ARE IN LIEU OF ALL OTHER WARRANTIES, WRITTEN OR ORAL, EXPRESS OR IMPLIED, WHETHER ARISING BY OPERATION OF LAW OR OTHERWISE,
WHETHER OR NOT THE PURPOSE HAS BEEN DISCLOSED AND WHETHER OR NOT THE EMERSON CEILING FAN HAS BEEN SPECIFICALLY DESIGNED OR
MANUFACTURED FOR YOUR USE OR PURPOSE. EMERSON HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION,
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE FOR COMPONENTS AND ACCESSORIES AS OF THE EXPIRATION OF THE
ONE YEAR WARRANTY PERIOD FOR SUCH COMPONENTS AND ACCESSORIES. IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE FOR THE MOTOR PORTION OF THE EMERSON CEILING FAN ARE LIKEWISE DISCLAIMED BY EMERSON AT SUCH TIME THAT THE EXPECTED LIFETIME
OF THE EMERSON CEILING FAN UNDER NORMAL USAGE HAS BEEN REACHED. EXCLUSIONS OR LIMITATIONS OF IMPLIED WARRANTIES MAY VARY FROM
STATE TO STATE AND PROVINCE TO PROVINCE SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
What We Will Do To Correct Problems:
If during the one (1) year warranty period the motor or any component or accessory of your Emerson Ceiling Fan is defective in materials or workmanship, or if during
the expected lifetime of the Emerson Ceiling Fan (when used in accordance with the User Manual or other instructions) the motor is defective in materials or
workmanship, you must contact Emerson during the applicable warranty period. If the defect is covered by warranty, Emerson will repair or replace the defective
motor, component or other accessory at no charge to you. If repair of the motor, component or accessory is not practical or possible within a reasonable time and no
replacement Emerson Ceiling Fan can be provided, Emerson will refund to you the actual purchase price of your Emerson Ceiling Fan. We will ship the repaired or the
replacement Emerson Ceiling Fan to you at no charge, but you are responsible for all costs of removal and reinstallation of your Emerson Ceiling Fan.
How You Can Receive Warranty Service:
You must be the original retail purchaser and have proof of your purchase of the Emerson Ceiling Fan to obtain your remedy under this limited warranty. You can
return your Emerson Ceiling Fan to your place of purchase, or you can call Emerson Customer Service at 1-800-237-6511 to obtain a return authorization and service
identification tag. In order for us to confirm that your Emerson Ceiling Fan is still under warranty, please retain your receipt or other proof of purchase and have that
information readily available when returning your Emerson Ceiling Fan to your place of purchase, or upon calling Emerson Customer Service. If you call Emerson
Customer Service, prior to your call please be prepared to provide all model numbers shown on your Emerson Ceiling Fan. Once we have processed your return
authorization request, we will provide you with a postage paid return label which should be affixed to the Emerson Ceiling Fan package you ship to the address listed at
the end of this limited warranty. The return label will be sent to the mailing address you provide to us by phone.
What Is Not Covered:
This limited warranty does not extend to and expressly excludes:
• The glass globes and light bulbs of your Emerson Ceiling Fan,
• Loss or damage to the motor or any component or accessory caused by normal wear and tear, rather than due to defects in materials or workmanship,
• Loss or damage resulting from conditions beyond our reasonable control, including without limitation, repairs not made at our factory or authorized service center,
use of parts or accessories not provided to you as part of this warranty by our factory or authorized service center, mishandling, unreasonable use, misuse, abuse,
modifications or other damage caused by you or a third party to your Emerson Ceiling Fan while not in our possession,
• Loss or damage resulting from improper installation, or other failure to comply with instructions in your Owner's Manual.
This limited warranty is deemed null and void upon the occurrence of either of the following events:
• You cease to own the Emerson Ceiling Fan product, or
• The Emerson Ceiling Fan is moved from its original point of installation.
This limited warranty is only valid within the 50 United States, the District of Columbia, and Canada. No other written or oral warranties apply, and no employee, agent,
dealer or other person is authorized to give any warranties on behalf of Air Comfort Products or Emerson Electric Co.
Limitation of Liability
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE TO YOU UNDER THIS LIMITED WARRANTY. TO THE EXTENT PERMITTED BY
LAW, IN NO EVENT SHALL EMERSON OR ANY EMERSON AUTHORIZED DEALER BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL
DAMAGES, INCLUDING ANY ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE OR INABILITY TO USE THE EMERSON CEILING
FAN OR FOR THE NEGLIGENCE OF EMERSON OR AN EMERSON AUTHORIZED DEALER. EMERSON SHALL NOT BE LIABLE FOR DAMAGES CAUSED BY DELAY IN
PERFORMANCE AND IN NO EVENT, REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF ACTION (WHETHER BASED IN CONTRACT, INFRINGEMENT,
NEGLIGENCE, STRICT LIABILITY, OTHER TORT OR OTHERWISE), SHALL EMERSON'S OR ANY EMERSON AUTHORIZED AGENT'S LIABILITY TO YOU OR ANY
INDIVIDUAL USING THE EMERSON CEILING FAN EXCEED THE PRICE PAID BY THE ORIGINAL OWNER FOR THE EMERSON CEILING FAN. The term "consequential
damages" shall include, but not be limited to, loss of anticipated profits, business interruption, loss of use or revenue, cost of capital or loss or damage to property or
equipment.
How State and Provincial Law Relates To The Warranty:
Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
19
emersonfans.com
Please contact 1-800-654-3545 for further assistance
ETL Model No.: CF921
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant • St. Louis, MO 63136
Questions, problems, missing parts: Before returning to the store call
Emerson Electric Customer Service
8 a.m. - 6 p.m., EST, Monday-Friday
1-800-654-3545
www.emersonfans.com
Retain this manual for future use.
Part No. F40BP74330003
Revision: 131015
Printed in China
10/13
Form No. BP7433-3
ETL Model No.: CF921
Download PDF