Data Sheet of SAW Components
Note : Murata SAW Component is applicable for Cellular /Cordless
phone (Terminal) relevant market only.
Please also read caution at the end of this document.
SAW FILTER FOR TD-SCDMA
Murata part number : SAFEA1G90AA0F00
Package Dimensions
Specification
Specification
Item
Top View
-30 to 85°C
25±2°C
typ.
1.35±0.05
(1)
Dot Marking(0.3)
B Q
Insertion Loss
(1880 to 1920MHz)
(0.17)
(5)
(4)
2-0.25±0.05
(3)
(0.075)
5-0.325±0.050
Bottom View
(2)
1900MHz
1.9 dB max.
1.7 dB max.
1.5 dB
Absolute Attenuation
(3)
0.5max.
(2)
Nominal Center Frequency(fc)
(4)
1.05±0.05
(5)
1)
0.1 to
1395 MHz
38 dB min.
38 dB min.
41 dB
2)
1395 to
1435 MHz
40 dB min.
40 dB min.
44 dB
3)
1435 to
1805 MHz
30 dB min.
30 dB min.
37 dB
4)
1805 to
1840 MHz
25 dB min.
25 dB min.
31 dB
5)
at
1850 MHz
15 dB min.
18 dB min.
23 dB
6)
2000 to
2135 MHz
25 dB min.
25 dB min.
28 dB
7)
2135 to
2175 MHz
35 dB min.
35 dB min.
40 dB
8)
2175 to
3500 MHz
30 dB min.
30 dB min.
34 dB
9)
3500 to
6000 MHz
21 dB min.
21 dB min.
25 dB
Ripple Deviation
(1880 to 1920MHz)
0.8 dB max.
0.6 dB max.
0.4 dB
VSWR
(1880 to 1920MHz)
1.9 max.
1.8 max.
1.3
(1)
(0.05)
2-0.25±0.05
5-0.25±0.05
2-0.25±0.05
Marking
: Laser Printing
(1) : Unbalance Port
(4) : Unbalance Port
Others : Ground
Unbalance Port Matching Impedance
(nominal)
Input Signal Level
50W
20mW (+13dBm), 2000 hours
Unit : mm
September. 4, 2009 ver.1
1/5
SAW FILTER FOR TD-SCDMA
Murata part number : SAFEA1G90AA0F00
Frequency Performance
・
・
September. 4, 2009 ver.1
2/5
SAW FILTER FOR TD-SCDMA
BQ
BQ
BQ
+0.1
0.8-0.0
4.0±0.1
0.30±0.05
Direction of Feed
3°max.
1.6±0.1
8.0±0.2
+0.1
1.5-0.0
2.00±0.05
3°max.
4.0±0.1
3.50±0.05
Dimensions of
Carrier Tape
1.75±0.10
Murata part number : SAFEA1G90AA0F00
0.70±0.10
Cover Tape
1.3±0.1
Unit: mm
Dimensions
of Tape
Trailer tape
178
160...190
Components
80...120
Leader Cavity
400...560
Unit: mm
Dimensions of Reel
2.0±0.5
2.0±0.5
13.0±0.5
13.5max.
(60)
330)
(100)
15.5max.
178)
9.0±0.5
9.5±1.0
13.0±0.5
Unit: mm
SAFEA1G90AA0F000R00 … 10000pcs/reel
September. 4, 2009 ver.1
SAFEA1G90AA0F00R15 … 5000pcs/reel
3/5
SAW FILTER FOR TD-SCDMA
Murata part number : SAFEA1G90AA0F00
Recommended Land Pattern
0.25
0.25
0.425
0.25
1.3
0.325
0.525
0.525
0.325
0.325
0.425
0.25
Top View
: Land Pattern
Unit : mm
1.6
Test Circuit
Bottom View
2
3
5
4
1
50Ω
September. 4, 2009 ver.1
50Ω
4/5
SAW FILTER FOR TD-SCDMA
Murata part number : SAFEA1G90AA0F00
RoHS Compliance
This component is compliant with RoHS directive.
This component was always RoHS compliant from the first date of manufacture.
・Caution - Limitation of Applications
This product is intended for the following applications only; however, please do not use this product in
these applications where defects might directly cause damage to a third party’s life, body or property.
a. Mobile Telephone
b. Cordless phone (except for Automotive use)
c. PC (Including Notebook PC, Netbook PC, Tablet)
d. Game
e. Camera (except for Business/security use)
f. Set Top Box
g. Electronic dictionary
h. Digital audio equipment
・This catalog is for reference only and not an official product specification document, therefore, please
review and approve our official product specification before ordering this product.
September. 4, 2009 ver.1
5/5
SAW FILTER FOR TD-SCDMA
Murata part number : SAFEA1G90AA0F00
Important notice
PLEASE READ THIS NOTICE BEFORE USING OUR PRODUCTS.
Please make sure that your product has been evaluated and confirmed from the aspect of the fitness for the
specifications of our product when our product is mounted to your product.
All the items and parameters in this product specification/datasheet/catalog have been prescribed on the premise that
our product is used for the purpose, under the condition and in the environment specified in this specification. You are
requested not to use our product deviating from the condition and the environment specified in this specification.
Please note that the only warranty that we provide regarding the products is its conformance to the specifications
provided herein. Accordingly, we shall not be responsible for any defects in products or equipment incorporating such
products, which are caused under the conditions other than those specified in this specification.
WE HEREBY DISCLAIMS ALL OTHER WARRANTIES REGARDING THE PRODUCTS, EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, THAT THEY
ARE DEFECT-FREE, OR AGAINST INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS.
The product shall not be used in any application listed below which requires especially high reliability for the prevention
of such defect as may directly cause damage to the third party's life, body or property. You acknowledge and agree
that, if you use our products in such applications, we will not be responsible for any failure to meet such requirements.
Furthermore, YOU AGREE TO INDEMNIFY AND DEFEND US AND OUR AFFILIATES AGAINST ALL CLAIMS,
DAMAGES, COSTS, AND EXPENSES THAT MAY BE INCURRED, INCLUDING WITHOUT LIMITATION,
ATTORNEY FEES AND COSTS, DUE TO THE USE OF OUR PRODUCTS IN SUCH APPLICATIONS.
- Aircraft equipment.
- Aerospace equipment
- Undersea equipment.
- Power plant control equipment - Medical equipment.
- Transportation equipment (vehicles, trains, ships, elevator, etc.).
- Traffic signal equipment.
- Disaster prevention / crime prevention equipment.
- Burning / explosion control equipment
- Application of similar complexity and/ or reliability requirements to the applications listed in the above.
We expressly prohibit you from analyzing, breaking, Reverse-Engineering, remodeling altering, and reproducing our
product. Our product cannot be used for the product which is prohibited from being manufactured, used, and sold by
the regulations and laws in the world.
We do not warrant or represent that any license, either express or implied, is granted under any our patent right,
copyright, mask work right, or our other intellectual property right relating to any combination, machine, or process in
which our products or services are used. Information provided by us regarding third-party products or services does
not constitute a license from us to use such products or services or a warranty or endorsement thereof. Use of such
information may require a license from a third party under the patents or other intellectual property of the third party, or
a license from us under our patents or other intellectual property.
Please do not use our products, our technical information and other data provided by us for the purpose of developing
of mass-destruction weapons and the purpose of military use.
Moreover, you must comply with "foreign exchange and foreign trade law", the "U.S. export administration regulations",
etc.
Please note that we may discontinue the manufacture of our products, due to reasons such as end of supply of
materials and/or components from our suppliers.
September. 4, 2009 ver.1
SAW FILTER FOR TD-SCDMA
Murata part number : SAFEA1G90AA0F00
Customer acknowledges that Murata will, if requested by you, conduct a failure analysis for defect or alleged defect of
Products only at the level required for consumer grade Products, and thus such analysis may not always be available
or be in accordance with your request (for example, in cases where the defect was caused by components in Products
supplied to Murata from a third party).
The product shall not be used in any other application/model than that of claimed to Murata.
Customer acknowledges that engineering samples may deviate from specifications and may contain defects due to
their development status.
We reject any liability or product warranty for engineering samples.
In particular we disclaim liability for damages caused by
・the use of the engineering sample other than for evaluation purposes, particularly the installation or integration in the
product to be sold by you,
・deviation or lapse in function of engineering sample,
・improper use of engineering samples.
We disclaims any liability for consequential and incidental damages.
If you can’t agree the above contents, you should inquire our sales.
September. 4, 2009 ver.1