Ariston NIO 844 DO B AUS Operating instructions

Operating Instructions
HOB
GB
GB
Contents
Installation, 2-3
English,1
Positioning
Electrical connection
Description of the appliance, 4
Control panel
Start-up and use, 5-8
NIO 844 DO B AUS
Switching on the hob
Switching on the cooking zones
Medium function
Booster function
Switching off the cooking zones
Programming the cooking duration
Timer
Control panel lock
Switching off the hob
“Demo” mode
Practical advice on using the appliance
Safety devices
Practical cooking advice
Precautions and tips, 9
General safety
Disposal
Care and maintenance, 10
Switching the appliance off
Cleaning the appliance
Disassembling the hob
Technical description of the models, 11
Service information, 12
min. 20 mm
COMPARTMENT
min. 40 mm
Positioning
790
75
3+
/- 1
51
0
/-
1
2+
49
Ventilation
To allow adequate ventilation and to avoid overheating of the
surrounding surfaces the hob should be positioned as follows:
• At a minimum distance of 40 mm from the back panel
or any other vertical surfaces.
• So that a minimum distance of 20 mm is maintained
between the installation cavity and the cabinet
underneath.
• Kitchen cabinets adjacent to the appliance and taller
than the top of the hob must be at least 600 mm from
the edge of the hob.
2
FAN-ASSISTED
OVEN
min. 40 mm
SUPPORTING
SURFACE
UNDERSIDE
OF HOB
30
FRONT SIDE
OF HOB
40
Built-in appliance
Use a suitable cabinet to ensure that the appliance
functions properly.
• The supporting surface must be heat-resistant up to a
temperature of approximately 100°C.
• If the appliance is to be installed above an oven, the
oven must be equipped with a forced ventilation
cooling system.
• Avoid installing the hob above a dishwasher: if this
cannot be avoided, place a waterproof separation
device between the two appliances.
• Depending on the hob you want to install, the cabinet
must have the following dimensions (see figure):
min. 20 mm
5 mm
! Keep all packaging material out of the reach of children.
It may present a choking or suffocation hazard (see
Precautions and tips).
! The appliance must be installed by a qualified
professional in accordance with the instructions provided.
Incorrect installation may cause harm to people and
animals or may damage property.
57
GB
! Before operating your new appliance please read this
instruction booklet carefully. It contains important
information concerning the safe operation, installation and
maintenance of the appliance.
! Please keep these operating instructions for future
reference. Pass them on to any new owners of the
appliance.
! A board must be installed under the hob if it is not
installed above an oven. Please, refer to the
“Installation Instructions” for minimum dimensions.
5 mm
Installation
Fixing
The appliance must be installed on a perfectly level
supporting surface.
Any deformities caused by improper fixing could affect
the features and operation of the hob.
The thickness of the supporting surface should be taken
into account when choosing the length of the screws for the
fixing hooks:
• 30 mm thick: 23 mm screws
• 40 mm thick: 13 mm screws
Fix the hob as follows:
1. Use short flat-bottomed screws to fix the 4 alignment
springs in the holes provided at the central point of each
side of the hob.
2. Place the hob in the cavity, make sure it is in a central
position and push down on the whole perimeter until the
hob is stuck to the supporting surface.
3. For hobs with raised sides: After inserting the hob into
its cavity, insert the 4 fixing hooks (each has its own pin)
into the lower edges of the hob, using the long pointed
screws to fix them in place, until the glass is stuck to the
supporting surface.
! The screws for the alignment springs must remain
accessible.
! In order to adhere to safety standards, the appliance
must not come into contact with electrical parts once it
has been installed.
! All parts which ensure the safe operation of the
appliance must not be removable without the aid of a tool.
Electrical connection
! The electrical connection for the hob and for any built-in
oven must be carried out separately, both for safety
purposes and to make extracting the oven easier.
Single-phase connection
Electrical cable
220-240V 1+N ~
50 Hz
GB
• 400V 3 - N ~ 50 Hz
• 400V - 2+2N ~ 50 Hz
Separate the wires and connect them in accordance with
the instructions given in the following table and diagrams:
Voltage and
mains frequency
400V - 2+N ~
50 Hz
Electrical cable
Wire connection
: yellow/green;
N: the two blue wires together
220-240V 3 ~
50Hz
L1: black
L2: brown
400V 3-N~ 50Hz
: yellow/green;
N1: blue
400V - 2+2N ~
50 Hz
N2: blue
L1: black
L2: brown
Connecting the electricity supply cable to the mains
If the appliance is being connected directly to the
electricity mains an omnipolar switch must be installed
with a minimum opening of 3 mm between contacts.
! The installer must ensure that the correct electrical
connection has been made and that it is fully compliant
with safety regulations.
Before connecting the appliance to the power supply,
make sure that:
• The appliance is earthed and the plug is compliant with
the law.
• The socket can withstand the maximum power of the
appliance, which is indicated on the data plate located
on the appliance itself.
• The voltage falls within the range of values indicated on
the data plate.
• The socket is compatible with the plug of the
appliance. If the socket is incompatible with the plug,
ask an authorised technician to replace it. Do not use
extension cords or multiple sockets.
! Once the appliance has been installed, the power
The hob is equipped with a pre-connected electricity
supply cable, which is designed for single-phase
connection. Connect the wires in accordance with the
instructions given in the following table and diagrams:
Voltage and
mains frequency
• 400V - 2+N ~ 50 Hz
• 220-240V 3 ~ 50 Hz
Wire connection
: yellow/green;
N: the two blue wires
together
L: brown and black
together
Other types of connection
If the mains supply corresponds with one of the following:
supply cable and the electrical socket must be easily
accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only.
! The manufacturer declines any liability should these
safety measures not be observed.
! Do not remove or replace the power supply cable for any
reason. Its removal or replacement will void the warranty
and the CE marking. INDESIT does not assume liability
for accidents or damage arising from replacement/
removal of the original power supply cable. Replacement
can only be accepted when carried out by personnel
authorised by INDESIT and using an original spare part.
Voltage and mains frequency
3
Description of the
appliance
Control panel
GB
The control panel described in this manual is only a representative example: it may not exactly match the panel
on your appliance.
BOOSTER
button
Booster
Booster
BOOSTER
indicator light
Booster
• INCREASE TIME button increases the time value
set on the timer (see Start-up and use).
• DECREASE TIME button decreases the time
value set on the timer (see Start-up and use).
• COOKING ZONE SELECTOR button shows a
particular cooking zone has been selected and
therefore various adjustments are possible.
• COOKING ZONE SELECTOR button is used to
select the desired cooking zone.
• POWER indicator provides a visual display for the
current heat level.
• ON/OFF button switches the appliance on and off.
• ON/OFF indicator light shows whether the
appliance is on or off.
• PROGRAMME TIMER button controls the cooking
programme times (see Start-up and use).
• PROGRAMME TIMER display shows which
programme has been selected (see Start-up and
use).
• COOKING ZONE PROGRAMMED indicator lights
show which cooking zones are being used during
a cooking programme (see Start-up and use).
• CONTROL PANEL LOCK button prevents
accidental changes to the hob settings (see Startup and use).
• CONTROL PANEL LOCK indicator light shows
the control panel has been locked (see Start-up
and use).
4
Booster
• COOKING ZONE POWER SELECTOR buttons
switch on the hotplate and control the power (see
Start-up and use).
• TIMER indicator light shows that the timer has
been activated
• BOOSTER button activates the booster function 3000 W - of the cooking zone (see Start-up and
use).
• BOOSTER indicator light shows that the booster
function has been activated.
! This product complies with the requirements of the
latest European Directive on the limitation of power
consumption of the standby mode.
If no operations are carried out for a period of 2
minutes, after the residual heat indicator lights turn
off and the fan stops (if present), the appliance
automatically switches to the “off mode”.
The appliance resumes the operating mode once the
ON/OFF button is pressed.
Start-up and use
! The glue applied on the gaskets leaves traces of
grease on the glass. Before using the appliance, we
recommend you remove these with a special nonabrasive cleaning product. During the first few hours
of use there may be a smell of rubber which will
disappear very quickly.
! A few seconds after the hob is connected to the
electricity supply, a buzzer will sound. The hob may
now be switched on.
Types of noise during normal hob operation:
• Buzz: due to the vibration of the metallic parts
that make up the induction element and the pot; it
is generated by the electromagnetic field required
for heating and increases as the power of the
induction element increases.
• Soft whistle: heard when the pot placed on the
heating zone is empty; the noise disappears once
food or water is placed into the pot.
• Crackle: produced by the vibration of materials
on the bottom of the pot due to the flow of
parasitic currents caused by electromagnetic
fields (induction); can be more or less intense
depending on the material making up the bottom
of the pot, and decreases as the pot dimensions
increase.
• Loud whistle: heard when two induction
elements of the same group function
simultaneously at maximum power and/or when
the booster function is set on the larger element
while the other is auto-adjusted. Noise is reduced
by decreasing the power level of the autoadjusted induction element; pot bottom layers
made of different kinds of materials are among
the main causes of this noise.
• Fan noise: a fan is necessary to ensure the hob
functions correctly and to safeguard the electronic
unit from possible overheating. The fan functions
at maximum power when the large induction
element is at maximum power or when the booster
function is on; in all other cases, it works at
average power depending on the temperature
detected. Furthermore, the fan may continue to
work even after switching the hob off, if the
temperature detected is high.
The types of noise listed above are due to induction
technology and are not necessarily operational
faults.
! If the
- +
or
button is pressed for an extended
period of time, the display scrolls quickly though the
power levels and timer minutes.
Switching on the hob
GB
To switch the hob on, press and hold the
button
for approximately one second.
Switching on the cooking zones
Each cooking zone is controlled using a selector
button
and a power adjustment device
consisting of power level selector buttons between
the values of 0 and 9.
• To begin operating a cooking zone, press the
corresponding control button and set the desired
power level using the power level selector buttons
between 0 and 9.
Switching off the cooking zones
To switch off a cooking zone, select it using the
corresponding selector button
and:
• Press power level selector button 0: this
immediately returns the power setting to 0 and the
cooking zone switches off.
Booster function
The booster function for some of the cooking zones
may be used to shorten heating-up times. It may be
activated by pressing the
Booster
/ Booster button. The
indicator light directly above the button will illuminate.
This function boosts the power to 2000 W or 3000 W,
depending on the size of the relevant cooking zone.
The booster stops automatically after 4 minutes. While
the booster for one of the cooking zones is active, the
corresponding front or rear cooking zone will operate at
a reduced power level (e.g. if the booster for the rear
left-hand hotplate has been activated, the power level
of the front left-hand hotplate will be reduced). For
further information, please refer to the Technical
description of the models.
Programming the cooking duration
! All the cooking zones may be programmed
simultaneously, for a duration between 1 and 99
minutes.
1. Select the cooking zone using the corresponding
selector button.
2. Adjust the power level of the cooking zone.
3. Press the
programming button. The indicator light
corresponding to the selected zone will start flashing.
5
GB
4. Set the cooking duration using the
- +
and
buttons.
5. Confirm by pressing the
button or automatic
selection occurs after 10 seconds.
The timer begins counting down immediately.
A buzzer sounds for approximately 1 minute and the
cooking zone switches off when the set programme
has finished.
Repeat the above procedure for each hotplate you
wish to programme.
Using multiple programmes and the display
If one or more hotplates are programmed, the display
will show the data for the hotplate with the least time
remaining, and the light corresponding to the position
of the hotplate will flash. The lights corresponding to
the other hotplates programmed will be switched on.
To visualise the time remaining for the other
programmed hotplates, press the
button.
3. Confirm by pressing the
The timer begins counting down immediately. When
the time has elapsed, a buzzer will sound (for one
minute).
Control panel lock
When the hob is switched on, it is possible to lock
the oven controls in order to avoid accidental
changes being made to the settings (by children,
during cleaning, etc.). Press the
button to lock
the control panel: the indicator light above the button
will switch on.
To use any of the controls (e.g. to stop cooking),
you must switch off this function. Press the
button for a few moments, the indicator light will
switch off and the lock function will be removed.
Switching off the hob
button
repeatedly: the time remaining for each
hotplate will be shown sequentially in a
clockwise order, starting from the front
left hotplate.
Press the button
to switch off the appliance - do not
Changing the programme
rely solely on the pan sensor.
If the control panel lock has been activated, the
controls will continue to be locked even after the hob
is switched on again. In order to switch the hob on
again, you must first remove the lock function.
1. Press the
“Demo” mode
button repeatedly until the duration
you wish to change is shown.
2. Use the
buttons to set the new duration.
3. Confirm by pressing the
button.
To cancel a programme, follow the above
instructions. At step 2, press the
-
button: the
duration decreases progressively until it reaches 0
and switches off. The programme resets and the
display exits programming mode.
Timer
programming button until the timer
indicator light is illuminated
.
2. Set the desired duration using the
buttons.
6
• Press and hold the
- +
and
+ and
buttons
simultaneously for 6 seconds. When the 6
seconds have elapsed, the ON/OFF and
CONTROLS LOCKED indicator lights will flash for
one second. Release the
press the
The hob must be switched on.
The timer can be used to set a duration up to 99
minutes.
1. Press the
It is possible to set the hob to a demonstration
mode where all the controls work normally but the
heating elements do not switch on. To activate the
“demo” mode the hob must be switched on, with all
the hotplates switched off.
+ and
buttons and
button;
• The display will show the text DE and MO and the
hob will be switched off.
• When the hob is switched on again it will be set to
the “demo” mode.
To exit this mode, follow the procedure described
above. The display will show the text DE and OF
and the hob will be switched off. When it is next
switched on, the hob will function normally.
will be switched off. When it is next switched on, the hob
will function normally.
• A pan whose diameter is too small
• The pan has been removed from the hotplate.
Practical advice on using the appliance
Overheating protection
! Use cookware made from materials which are compatible
with the induction principle (ferromagnetic material). We
especially recommend pans made from: cast iron,
coated steel or special stainless steel adapted for
induction. Use a magnet to test the compatibility of the
cookware.
If the electronic elements overheat, the hob switches off
SUITABLE
UNSUITABLE
*
Cast iron
Enamelled steel
Special stainless steel
Copper,
Aluminium, Glass, Earthenware,
Ceramic, non magnetic Stainless steel
In addition, to obtain the best results from your hob:
• Use pans with a thick, flat base in order to fully utilise
the cooking zone.
automatically and
GB
F appears on the display, followed by a
flashing number. When the temperature has reached a
suitable level, this message disappears and the hob may
be used again.
Safety switch
The appliance has a safety switch which automatically
switches the cooking zones off after they have been in
operation for a certain amount of time at a particular
power level. When the safety switch has been triggered,
0 ”.
the display shows “0
For example: the rear right-hand hotplate is set to 5 and
will switch off after 7 and a half hours of continuous
operation, while the front left-hand hotplate is set to 2 and
will switch off after 9 and a half hours.
Buzzer
• Always use pans with a diameter which is large enough
to cover the hotplate fully, in order to use all the
available heat.
• Make sure that the base of the cookware is always
clean and dry, in order to fully utilise and extend the life
of both the cooking zones and the cookware.
• Avoid using the same cookware which has been used
on gas burners: the heat concentration on gas burners
may distort the base of the pan, causing it not to
adhere correctly.
Safety devices
Pan sensor
Each cooking zone is equipped with a pan sensor device.
The hotplate only emits heat when a pan with suitable
measurements for the cooking zone is placed on it. If
the power level indicator display flashes, this may be
because:
• An incompatible pan
This can also indicate several irregularities:
• An object (a pan, cutlery, etc.) has been placed on the
control panel for more than 10 seconds.
• Something has been spilt on the control panel.
• A button has been pressed for too long. All of the
above situations may cause the buzzer to sound.
Remove the cause of the malfunction to stop the
buzzer. If the cause of the problem is not removed, the
buzzer will keep sounding and the hob will switch off.
Power level
Maximum operating time in hours
1
9
2
8
3
7
4
6
5
5
6
4
7
3
8
2
9
1
7
Practical cooking advice
Very
low-flame
cooking
Low-flame
cooking
Medium-flame cooking
High-flame
cooking
Very high-flame
cooking
GB
8
ª
•
•
¶
¶
§
§
S
S
¢
¢
£
™
™
¡
Pressure cooking
Pressure cooker
Frying
Grilling
Boiling
Crêpes
Cooking on a high flame and browning
(roasts, steaks, escalopes, fish fillets,
fried eggs)
Fast thickening (liquid juices)
Boiling water (pasta, rice, vegetables)
Milk
Slow thickening (dense juices)
Bain-marie cooking
Low-flame cooking (stews)
Chocolate sauce
Pressure cooking after whistle
Reheating dishes
Keeping food hot
Precautions and tips
! This appliance has been designed and manufactured in
compliance with international safety standards. The
following warnings are provided for safety reasons and
must be read carefully.
This appliance conforms to the following European
Economic Community directives:
- 2006/95/EEC dated 12/12/06 (Low Voltage) and
subsequent amendments;
- 2004/108/EEC dated 15/12/04 (Electromagnetic
Compatibility) and subsequent amendments;
- 93/68/EEC dated 22/07/93 and subsequent amendments.
- 1275/2008 stand-by/off mode.
General safety
! Make sure that the air inlet behind the fan grille is never
obstructed. The built-in hob should, in fact, be provided
with suitable ventilation for the cooling of the electronic
components used in the appliance.
! We advise against the installation of an induction hob
above an under-the-counter refrigerator (heat) or above a
washing machine (vibrations). In fact, there would be
insufficient space for the ventilation of electronic
components.
• The appliance was designed for domestic use inside the
home and is not intended for commercial or industrial
use.
• The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
• Do not touch the appliance when barefoot or with wet or
damp hands and feet.
• The appliance must be used by adults only for the
preparation of food, in accordance with the instructions
provided in this booklet. Do not use the hob as a
worktop or chopping board.
• The glass ceramic hob is resistant to mechanical
shocks, but it may crack (or even break) if hit with a
sharp object such as a tool. If this happens, disconnect
the appliance from the electricity mains immediately to
avoid electric shock, and contact a Service Centre.
• Ensure that power supply cables of other electrical
appliances do not come into contact with the hot parts of
the hob.
• Remember that the cooking zones remain relatively hot
for at least thirty minutes after they have been switched
off. An indicator light provides a warning when residual
heat is present (see Start-up and use).
• Keep any object which could melt away from the hob, for
example plastic and aluminium objects, or products with
a high sugar content. Be especially careful when using
plastic film and aluminium foil or packaging: if placed on
surfaces which are still hot, they may cause serious
damage to the hob.
• Always make sure that pan handles are turned towards
the centre of the hob in order to avoid accidental burns.
• When unplugging the appliance, always pull the plug
from the mains socket; do not pull on the cable.
• Never perform any cleaning or maintenance work without
having disconnected the appliance from the electricity
mains.
• The appliance should not be operated by people
(including children) with reduced physical, sensory or
mental capacities, by inexperienced individuals or by
anyone who is not familiar with the product. These
individuals should, at the very least, be supervised by
someone who assumes responsibility for their safety or
receive preliminary instructions relating to the operation
of the appliance.
• For the attention of wearers of
pacemakers or other active implants:
The hob complies with all current standards on
electromagnetic interference.
Your induction hob is therefore perfectly in keeping with
legal requirements (89/336/CEE directives). It is
designed not to create interference on any other
electrical apparatus being used on condition that the
apparatus in question also complies with this legislation.
Your induction hob generates short-range magnetic
fields. To avoid any interference between your induction
hob and a pacemaker, the latter must be designed to
comply with relevant regulations. In this respect, we can
only guarantee our own product conformity. Please
consult the pacemaker manufacturer or your doctor
concerning its conformity or any possible incompatibility.
• Do not let children play with the appliance.
• Do not place metal objects (knives, spoons, pan lids,
etc.) on the hob as they may become hot.
• The appliance is not intended to be operated
by means of an external timer or separate
remote-control system.
• Children should be supervised to ensure
that they do not play with the appliance.
9
GB
Care and maintenance
Switching the appliance off
GB
Disconnect your appliance from the electricity
supply before carrying out any work on it.
Cleaning the appliance
! Do not use abrasive or corrosive detergents (for
example, products in spray cans for cleaning
barbecues and ovens), stain removers, anti-rust
products, powder detergents or sponges with
abrasive surfaces: these may scratch the surface
beyond repair.
! Never use steam cleaners or pressure cleaners on
Stainless steel frame (only in models with outer
frame)
Stainless steel can be marked by hard water which
has been left on the surface for a long time, or by
cleaning products containing phosphorus.
After cleaning, it is advisable to rinse the surface
well and dry it thoroughly. If water is spilt on the
surface, dry it quickly and thoroughly.
! Some hobs have an aluminium frame which is
similar to stainless steel. Do not use any cleaning or
degreasing products which are not suitable for use
with aluminium.
the appliance.
Disassembling the hob
• It is usually sufficient simply to wash the hob
using a damp sponge and dry it with absorbent
kitchen towel.
If it is necessary to disassemble the hob:
1. Loosen the screws fixing the alignment springs on
each side.
2. Loosen the screws holding the fixing hooks in
each corner.
3. Take the hob out of its installation cavity.
• If the hob is particularly dirty, rub it with a special
glass ceramic cleaning product, then rinse well
and dry thoroughly.
• To remove more stubborn dirt, use the scraper
provided. Remove spills as soon as possible,
without waiting for the appliance to cool, to avoid
residues forming crusty deposits. You can obtain
excellent results by using a rust-proof steel wire
sponge - specifically designed for glass ceramic
surfaces - soaked in soapy water.
! The scraper provided is sharp: be careful when
using it.
• If any plastic or sugary substances are
accidentally melted on the hob, remove them
immediately with the scraper, while the surface is
still hot.
• Once it is clean, the hob may be treated with a
special protective maintenance product: the
invisible film left by this product protects the
surface from drips during cooking. This
maintenance task should be carried out while the
appliance is warm (not hot) or cold.
• Always remember to rinse the appliance well with
clean water and dry it thoroughly: residues can
become encrusted during subsequent cooking
processes.
10
! Do not attempt to repair the appliance yourself. If
the appliance breaks down, contact a Service
Centre.
Disposal
• When disposing of packaging material: observe local
legislation so that the packaging may be reused.
• The European Directive 2002/96/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states that
household appliances should not be disposed of using the
normal solid urban waste cycle. Exhausted appliances
should be collected separately in order to optimise the cost
of re-using and recycling the materials inside the machine,
while preventing potential damage to the atmosphere and
to public health. The crossed-out dustbin is marked on all
products to remind the owner of their obligations regarding
separated waste collection. For further information relating
to the correct disposal of exhausted household appliances,
owners may contact the public service provided or their
local dealer.
Technical description of
the models
The induction system is the quickest existing way of cooking. Unlike traditional hotplates where the cooking
zone heats up, with the induction system heat is generated directly inside pans which have ferromagnetic
bases.
Hobs
Cooking zone
Back Left
Back Right
Front Left
Front Right
Total power
GB
NIO 844 DO B AUS
Power (W)
I 1400 – 600 if front left*
I 2200 – B 3000* - 1600 if front right*
I 2200 – B 3000* - 1600 if back left*
I 1400 – B 2000* – 600 if back right*
7200
Key:
I = single induction cooking zone
B = booster: the power of the cooking zone may be boosted to 3000 W
* = the maximum power level is limited while the booster is activated for the relevant rear cooking zone (see
Start-up and use).
11
09/2011 - 195094584.00
XEROX FABRIANO
GB
AUSTRALIA
ARISIT PTY LIMITED
40-44 Mark Anthony Drive, Dandenong South,
VIC 3175, Australia
Fax: Service & Sales (03) 9768 0838
Email: consumer.care@arisit.com
NEW ZEALAND
ARISIT PTY LIMITED
PO Box 68-140 Newton, Auckland
1145, New Zealand
Fax: (09) 302 0077
Email: sales@aristonappliances.co.nz
12
ARISTON
PRIORITY SERVICE
If you are not completely
satisfied with your appliance
or require service call:
Australia
Phone: 1300 815 589
New Zealand
Phone: (09) 306 1020
GENUINE ACCESSORIES
& SPARE PARTS
A wide range of genuine
accessories are available
for your appliance call:
Australia
Phone: 03 9768 0888
New Zealand