Auto Page | RS-662 | RS-662 OPER Manual 5x8 83006

RS-662
PROFESSIONAL REMOTE CAR STARTER
&
SECURITY / ALARM SYSTEM
OPERATIONS MANUAL
Please register your product at
www.autopageusa.com
THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY
1
SYSTEM OPERATIONS:
WARNINGS:
As with any product that performs automatic functions, there are certain safety
precautions that you must practice and be aware of.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Keep the transmitter out of children’s reach.
Do not leave anyone in the vehicle while running on remote control.
Alert servicing personnel that the vehicle can be started automatically.
Do not start the vehicle by remote while it’s in an enclosed area or garage.
Always apply the parking brake and lock the vehicle as you exit the vehicle.
The vehicle windows must be rolled up.
Should the unit malfunction, disconnect the fuse until the problem is corrected.
The use and operations of this system is the sole responsibility of the operator.
Some areas may have local ordinances that prohibit leaving a vehicle running
on public streets.
10. It is not safe to remote start the vehicle if the vehicle is parked on a steep
incline.
Transmitter
Button
System Function
Remark
Lock Doors (Arm System)
Arm System
Press and Hold for 3 seconds.
Panic function
Press
to stop panic.
Car Locator
Push while the system is armed
-
Arm system & Delete sensor
Press twice within 3 seconds
+
Silent Lock / Unlock
Ignition in "off" position.
Unlock Doors (Disarm System)
+
II
Two Step Door Unlock (Driver’s door
on the first push; Passenger’s door
on the second push) Optional
Trunk Release (Channel 2)
Press twice within 3 seconds.
Press and Hold for 2 seconds
Passive Arming By-pass
While the system Disarmed.
Channel # 4 Timer Output (4)
Optional
Activate or Turn Off The Remote
Start
Switching Code For 2nd Car
Operation.
Push once or twice depending on
system settings (Program)
2
Push Before Command
CHANGING THE BATTERY IN YOUR TRANSMITTERS
XT-33: This transmitter uses two (2) 3-volt lithium ion batteries
(#CR2016) that are sandwiched together with the (+) side facing upward.
To replace the battery, you will need to use a small flat blade screwdriver.
Locate the small notch on the lower right side of the transmitter case
next to the key ring. Using the flat blade screwdriver, carefully pry the
top case from the bottom case. It should snap apart after breaking the
seal. Before removing the batteries note the direction of the positive (+)
terminal. Place the new batteries in exactly the same manner, being
careful not to bend or damage the contact terminal. Snap the cases
back together and then test the transmitter to insure it arms and disarms
the alarm.
XT-65: This transmitter uses one 3-volt battery. Please use the
procedure above to replace this battery.
XT-65 Extended
Range Sliding Cover remote
XT-33 Standard Remote
(2) CR2016
3-Volt Batteries
CR2032
3-Volt Battery
ACTIVE LOCK & ARM:
button on the transmitter.
1. Press
2. The Siren will chirp once and parking lights will flash once indicating
that the system is now active. The vehicle doors will lock upon
activating only when interfaced with the factory keyless entry system.
+
buttons
SILENT ARMING / DISARMING: Pressing the
together on the transmitter will lock or unlock your system, No chirp
sound will be heard. Lock / unlock confirmation will be seen through the
vehicle’s parking lights only.
3
DEFECTIVE SENSOR REMINDER: If the siren sounds 3 chirps when
arming, then you have left a door, trunk or hood lid ajar.
SHOCK SENSOR / OPTIONAL SENSOR BY-PASS:
Press the
button once: The siren chirps once, the system is armed.
Press the
button a second time within 5 seconds: The siren chirps
twice, the Shock Sensor is now bypassed. The sensor bypass feature is
programmed to activate for one arming cycle only. The security system
will return to normal operation during the next arming cycle.
PASSIVE ARMING
Active arming / disarming are controlling your security system via the
remote transmitter. This security system is equipped with an optional
Passive Arming feature, which allows the security system to arm 30
seconds after the last door is closed. Operation is as follows:
1. Turn the ignition to the “OFF” position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash
fast for 30 seconds. If you re-open any door / hood / trunk, the
security system LED will stop flashing. It will begin flashing again
once all vehicle entrances are closed.
After 30-second timer has elapsed, the security system will automatically
“ARM”. The siren will chirp [1] time and the parking lights will flash [1]
time.
PASSIVE ARMING WITH PASSIVE DOOR LOCKING
The vehicle doors will automatically lock after passive arming cycle
has been completed. Please refer to your installing dealer to activate
this feature.
PASSIVE ARMING BY-PASS: While the LED is flashing fast for passive
buttons twice, the security
arming or Automatic re-arm, Press the
will respond with [1] chirp and LED will turn “ON”. The security system
will remain in this temporary state for as long as you wish.
or
button and the system will
To exit passive by-pass, press the
return to normal status.
ACTIVE UNLOCK & DISARMING:
1. Press
button on the transmitter.
2. The siren will chirp twice and parking light will flash twice to indicating
that the keyless system is now unlocked. The vehicle doors will
unlock and dome lights will turn on for 30 seconds.
TAMPER DISARMING: If the alarm was triggered in your absence, upon
disarming the system, the siren will chirp 4 times, the parking lights will
flash 3 times. This will notify you that the alarm has been triggered.
4
PATHWAY ILLUMINATION
This feature turns the parking light “ON” for 30 seconds upon the unlock
signal and for 10 seconds upon the lock signal. (Programmable)
TWO STEPS DOOR UNLOCK: This feature will independently unlock
the driver door only when deactivating the system. Pushing the
button a second time within 3 seconds will unlock the entire vehicle.
LED DISPLAY:
LED
Function
Off
Disarmed
Slow Flash
Armed
LED
Function
Zone 1 / Warn-Away Trigger
On (Solid)
Valet Mode
Quickly
Flashing
Passive arming
2 Flashes...
pause
3 Flashes...
pause
4 Flashes...
pause
5 Flashes...
pause
Zone 2 / Trigger Trunk/Hood
Zone3/ Trigger on Door Switch
Zone4/Trigger on Impact
Sensor
Zone 5 / Trigger Ignition Switch
CHIRP INDICATOR:
Chirp
Function
Parking light
1 Chirp
Arm
1 flash
Function
Arm
2 Chirps
Disarm
2 flashes
Disarm
3 Chirps
Defective Reminder
3 flashes
Disarm / Triggered
4 Chirps
Disarm / Triggered
12 flashes
Car Locator
6 Chirps
Car Locator
Constant On
Under Remote Start
PARKING LIGHTS:
1. Arming
Siren / Horn
1 or 3 Chirps
Parking Light
1 Flash
2. Disarming
2 or 4 Chirps 2 or 3 Flashes
3. Trigger
4. Panic
Alarming
Alarming
Flashes
Flashes
5. Car Locator
6 Chirps
12 Flashes
LED
Slow Flash
Doors
Locking
Starter
Disable
Unlocking
Slow Flash
Disable
Dome Light
Turns on for
30 -second
Flashes
Flashes
Locking
AUTOMATIC RE-ARM
If this feature or passive arming has been selected, the security
system will automatically re-arm itself 60 seconds after disarming with
remote transmitter. Automatic rearm will cancel if any door is opened
before the 60 seconds timer has elapsed. Please refer to your
installing dealer to activate this feature.
5
DEACTIVATING WITHOUT A TRANSMITTER
The Override function may be used if the remote transmitter is lost or
inoperative.
1. Enter the vehicle and turn the ignition switch to ‘ON’ position.
2. Within 10 seconds push and release the valet switch when the
in-dash LED stays on solid.
You can now start and operate the vehicle normally.
VALET MODE:
The valet switch allows you to temporarily bypass all system function,
eliminating the need to hand your transmitter to parking attendants or
garage mechanics. When the system is in valet mode, and remote start
functions are bypassed, however, the remote panic feature and remote
door locks will remain operational. To use the valet mode, the system
must first be deactivated either by using you remote transmitter, or by
operating the Manual override sequence.
Enter Valet Mode:
1. From the Unlock condition, turn the ignition to “ON” position.
2. Push and hold valet switch for 2 seconds until the LED turns on.
The LED will remain on as long as the system is in ‘valet mode’.
Exit Valet Mode:
1. Return to normal operation, turn ignition ‘on’.
2. Push and hold valet switch for 2 seconds, The LED will turn off
indicating the system has exited the valet mode.
PANIC FUNCTION: (IF SIREN or HORN IS INSTALLED)
The transmitter can be used as a remote panic switch to manually
trigger the vehicle’s siren in case of emergency.
button for 3 second. The siren will
1. Press and hold the
immediately sound.
2. During panic mode, the normal function of this transmitter button
and
buttons can be used to lock and
will be suspended. The
unlock the doors (if the option is installed),
3. To stop the panic, press the
button on the transmitter again.
4. If no buttons are pressed, the panic function will stop automatically
in 30 seconds.
TRIGGER THE SYSTEM
When armed, your vehicle is protected as follows:
1. Light impacts will trigger the warn-away with 3 long chirps from
siren/horn.
2. Heavy impacts / Doors open / Hood open / Trunk open / Turn on the
ignition key will all trigger the programmed sequence.
The starter disable relay (if installed) prevents the vehicle’s starter
from cranking. The siren, horn, parking lights, and dome light will
6
turn on alerting of an intrusion for 30 seconds. Then it will stop and
automatic reset and re-arm. If one of the sensors or detectors is still
active, the alarm system will sound a maximum of 6 times of 30
seconds cycles.
DOME LIGHT CONVENIENCE DELAY & SUPERVISION
This system has a unique feature, which will turn on your vehicle
dome light as follows: (optional) Additional installation required.
1. Upon unlocking, the interior lights will remain on for 30 seconds.
Note: Turning on the ignition switch or activating the system will turn
off the dome light.
IGNITION CONTROL DOOR LOCKS
If the vehicle’s door locks have been interfaced to the security system,
the system will automatically lock the vehicle’s doors when the ignition
is turned “ON” and /or unlock the vehicle’s doors when the ignition is
turned “OFF”.
TRUNK RELEASE (Additional Installation Required)
button on transmitter for two seconds to remote
Press and hold the
control the trunk release or other electric devices.
CAR LOCATOR (ONLY IF SIREN or HORN IS INSTALLED)
Press the
button when the system is armed to active car locator
function. The siren will chirp 6 times. The parking light will flash 12 times,
for you to easily locate your car.
REMOTE START OPERATION:
WARNINGS:
As with any product that performs automatic functions, there are certain
safety precautions that you must practice and be aware of.
1. Keep the transmitter out of children’s reach.
2. Do not leave anyone in the vehicle while running on remote control.
3. Alert servicing personnel that the vehicle can be started automatically.
4. Do not start the vehicle by remote while it’s in an enclosed area or
garage.
5. Always apply the parking brake and lock the vehicle as you exit the
vehicle.
6. Should the unit malfunction, disconnect the fuse until the problem is
corrected.
7. The use and operations of this system is the sole responsibility of the
operator.
8. Some areas may have local ordinances that prohibit leaving a vehicle
running on public streets.
7
A. TO REMOTE START THE VEHICLE:
When you want to start your vehicle,
button once on the transmitter.
1. Press
2. The parking lights will flash to indicate the remote start received the
signal.
3. The engine will start in approximately 5 seconds.
4. A few seconds after the engine is running, the parking lights will turn
on again and climate controls will activate and adjust the vehicles
interior temperature to your preset setting.
5. The vehicle will run for a 5 to 30 minute cycle and automatically shut
down.
(SAFETY START OPERATION :)
button twice before
The safety start feature allows you to press the
the vehicle will remote start or remote shut down. (Programming
Required)
NOTE: The Remote Start Unit will not start the vehicle if any one of the
following conditions exists:
1. The hood is opened.
2. The brake pedal is pressed.
3. The optional remote start enable toggle switch is in the OFF position.
4. The gear selector is in any gear other then “PARK” or “NEUTRAL”
TO TURN OFF THE REMOTE START:
When the engine is running (by remote start), if you want to stop it,
button once on the transmitter.
1. Press
2. Move the optional remote start enable toggle switch to OFF position.
(If installed)
3. Press the brake pedal, the vehicle will shut down and turn off the
parking light to indicate engine stopped.
TO OVERRIDE VEHICLE FROM REMOTE START CONTROL:
To operate the vehicle while running in the remote start mode.
1. Insert the ignition key and turn it to “ON” (not the start) position.
2. Press the brake pedal.
Note: If the brake pedal is pressed before the key is in the ON
position, the engine will shut down.
TEMPORARY STOP FEATURE:
This feature allows the vehicle to remain running after the key has been
removed from the ignition. This feature is useful for occasions when you
wish to exit and lock the vehicle for short periods of time, but would like
to leave the engine running and the climate control on.
button once on the
1. Before turning off the engine, press the
transmitter. The parking lights will come on and the LED will flash 3
8
times to confirm Temporary Stop feature ‘ON’
2. Turn the ignition key to OFF position. (The engine will stay running.)
3. The engine will run until the pre-programmed time elapsed or
shutdown input is received.
TIMER START: You must fully understand this feature to operate the
remote start safely. Use caution in using this feature.
This unit can be programmed to start and run the engine every 3 hours.
The engine will run for the programmed run time and then shut down.
IMPORTANT: Timer Start should be used only in open areas, NEVER
start and run the vehicle in on enclosed space such as a garage or
carport.
Three hours timer start: This feature is design for an extreme cold
climate usage. The system will auto start the vehicle every 3 hours, to
prevent engine freezing and hard to start.
A maximum of six cycles can occur.
ENTER:
button once to remote start the vehicle. As soon as the
1. Press the
vehicle is running the parking lights will turn ‘ON’.
2. Immediately press the
button then press
button. The parking
lights will flash (3) times. The siren chirps (3) times. The vehicle is
now programmed to start every (3) hours.
3. Press the brake pedal to stop the vehicle running.
Exit the timer start:
Timer start can be exited manually as follows:
1. Repeat the Enter Steps from above.
Or
1. Make sure the remote start system is not operating the engine.
2. Turn the ignition on. The LED and parking light will flash (4) times.
The siren chirps (4) times.
SHUTDOWN INPUT FOR REMOTE STARTER:
If any of the following conditions exist while the system is operating, the
engine will not start or will shut down immediately:
1. The hood is opened.
2. The brake pedal is pressed.
3. The optional remote start enable toggle switch is in the OFF position.
4. Engine is over-revved. {“Tachometer checking type” only}
5. The pre-programmed run time (5 /10 / 20 / 30 minutes) has elapsed.
9
button is pressed.
6. Transmitter
7. The vehicle refused to start running after {3} unsuccessful attempts.
DISABLING THE REMOTE START SYSTEM: (If Optional toggle switch
is installed)
This feature allows your system’s remote start unit to be temporarily
disabled to prevent the vehicle from being remote started accidentally.
This feature is useful if the vehicle is being serviced or stored in an
enclosed area. To disable the remote start, move the optional remote
start enable toggle switch to the OFF position.
OPTIONAL EQUIPMENT:
XT-42 / Antenna Kit: This is an optional package that will enable your unit to have two-way
communications and paging capabilities with the handheld remote. The optional kit includes a
XT-42LCD remote transceiver as well as the TRX-76 two-way antenna module. Please see
your authorized Autopage dealer for information and pricing of this option.
LIMITED LIFETIME WARRANTY PROVISIONS
( U.S. ,Continental U.S. and Canada Only)
1.
Auto Page, Inc. WARRANTS that this new unit has been thoroughly inspected and tested at
the factory prior to delivery. Your Auto Page equipment is guaranteed for “life” to the
original purchaser/user of the equipment and the original vehicle in which it was installed by
an authorized installer under the following conditions: If the product proves defective
(according to Auto Page's testing) within the first year, the defective unit may be exchanged or
repaired free of charge. “Proof of Purchase” (dated sales receipt) must accompany all
warranty returns; otherwise, your return will be rejected and sent back. After one (1) year,
the purchaser should ship the unit prepaid to Auto Page with a money order in the amount of
$30.00 to cover shipping and handling charges. Note: The product needs to be registered
online at time of installation. www.autopageusa.com
2.
This WARRANTY will be considered void if the equipment has been misused, neglected,
improperly serviced or installed, altered, dropped or damaged by water, contrary to the Auto
Page OPERATIONS MANUAL. Or, if used with accessories not approved by Auto Page,
which may have contributed to the defect. See note below regarding product installation**.
3.
The purchaser’s remedies under this WARRANTY shall be limited to the repair or
replacement of electronic components only. THE FOLLOWING IS NOT COVERED:
Damages or deterioration to cases, batteries, covers and cabinets; the cost of repairs,
replacement and labor of which shall be borne by the purchaser even if occurring during the
WARRANTY period.
4.
Any equipment or parts which are claimed to be defective under this WARRANTY must be
sent to the Auto Page Service center with “proof of purchase” at the purchaser’s expense prior
to such return, a Return Authorization Number should be obtained. Auto Page will return the
equipment, charges prepaid. Warranty Service can be provided through the dealer where the
equipment is originally purchased.
10
5.
Any unexpired WARRANTY shall be applicable to equipment and parts in the possession of
the original purchaser only.
6.
THIS WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESSED
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
7.
Auto Page shall not be liable, under the foregoing WARRANTIES or otherwise, for: Any
personal injury of any kind to the purchaser, its employees or agents or anyone else
whomsoever resulting directly or indirectly from the use or presence of the equipment or parts;
Consequential damages of any kind; any inability of the purchaser to use the equipment.
**IMPORTANT NOTE:
Any damages to the alarm system resulting from an
installation performed by anyone other than a professional installation technician
authorized by a dealer of Auto Page will void the product’s limited lifetime warranty.
Auto Page Warranty:
You must register your product online at
http://www.autopageusa.com to receive any warranty service.
Please go to the customer service tab and select product
registration.
It is the purchaser’s responsibility to register this
product for any future warranty service.
Warning: Some batteries may contain Perchlorate
What is Perchlorate? Perchlorate is both a naturally occurring and
manmade contaminant increasingly found in groundwater, surface water and soil.
Most perchlorate manufactured in the U.S. is used as an ingredient in solid fuel for
rockets and missiles. In addition, perchlorate-based chemicals are also used in the
construction of highway safety flares, fireworks, pyrotechnics, explosives, common
batteries, and automobile restraint systems. Perchlorate contamination has been
reported in at least 20 states. Perchlorate greatly impacts human health by
interfering with iodide uptake into the thyroid gland. In adults, the thyroid gland helps
regulate the metabolism by releasing hormones, while in children; the thyroid helps
in proper development. Perchlorate is becoming a serious threat to human health
and water resources.
“Perchlorate Material – Special handling may apply.”
For more information, go to
http://www.dtsc.ca.gov/hazardouswaste/perchlorate/
11
12
960 Knox Street Unit B, Torrance, CA 90502
Tel: (310) 323-1800 or (800) 262-2527 www.autopageusa.com
13
Download PDF