Lennox-AC-Remote-Controller-Owners-Manual-20pp Jan-2012

Lennox-AC-Remote-Controller-Owners-Manual-20pp Jan-2012
Before using your air conditioner, please
read this manual carefully and keep it for
future reference.
OWNER’S MANUAL
FOR THE
AIR CONDITIONER
REMOTE CONTROLLER
Congratulations on your purchase
of a Lennox air conditioner
NOTE:
This remote controller will only function
with the following Lennox inverter models –
Australia 13 23 50 New Zealand 0800 653 330
Web www.lennoxaus.com.au
E963_Lennox AC Remote Controller 16pp A5_3.indd 16-1
LNIV2610
LNIV3510
LNIV5010
LNIV6510
Read this manual
Inside you will find many helpful hints on how to use
and maintain your air conditioner properly. Just a little
preventative care on your part can save you a great deal
of time and money over the life of your air conditioner.
You’ll find many answers to common problems in the
chart of troubleshooting tips. If you review the chart of
Troubleshooting Tips first, you may not need to call for
service.
23/01/12 9:27 AM
CONTENTS
HANDLING THE REMOTE CONTROLLER
HANDLING THE REMOTE CONTROLLER .......... 3
Replacing batteries
Location of the remote controller ........................ 3
NOTE: Replace the batteries when there is no receiving beep
from the indoor unit or if the transmission indicator on the
remote controller fails to light.
Replacing batteries ........................................... 3
8m
REMOTE CONTROLLER SPECIFICATIONS ....... 4
The remote controller is powered by two dry cell batteries
(R03/LR03X2) housed in the rear part and protected by a
cover.
PERFORMANCE FEATURES .............................. 4
(1) Remove the cover by pressing and sliding it off.
FUNCTION BUTTONS ....................................... 6
(2) Remove the old batteries and insert the new batteries,
placing the (+) and (-) ends correctly.
(3) Re-attach the cover by sliding it back into position.
INDICATORS ON LCD ...................................... 9
HOW TO USE THE BUTTONS ......................... 10
Location of the remote controller
Auto operation ................................................ 10
• Use the remote controller within a distance of 8 metres
from the appliance, pointing it towards the receiver.
Reception is confirmed by a beep.
Cooling/Heating/Fan operation ......................... 10
Dehumidifying operation .................................. 11
Adjusting air flow direction ............................... 11
CAUTION
Timer operation .............................................. 12
• The air conditioner will not operate if curtains, doors
or other materials block the signals from the remote
controller to the indoor unit.
SLEEP / FRESH function .................................. 15
LED / FOLLOW ME function ............................. 15
NOTE: When the batteries are removed, the remote
controller erases all programming. After inserting new
batteries, the remote controller must be reprogrammed.
CAUTION
• Do not mix old and new batteries or batteries of
different types.
• Do not leave the batteries in the remote controller if
they are not going to be used for 2 or 3 months.
• Do not dispose batteries as unsorted municipal
waste. Collection of such waste separately for special
treatment is necessary.
• Prevent any liquid from falling into the remote
controller. Do not expose the remote controller to
direct sunlight or heat.
TURBO / SELF-CLEAN function ........................ 15
• If the infrared signal receiver on the indoor unit is
exposed to direct sunlight, the air conditioner may
not function properly. Use curtains to prevent the
sunlight from falling on the receiver.
• If other electrical appliances react to the remote
controller. either move these appliances or consult
your local dealer.
The design and specifications are subject to change without
prior notice for product improvement. Consult with the sales
agency or manufacturer for details
2
E963_Lennox AC Remote Controller 16pp A5_3.indd 2-3
3
23/01/12 9:27 AM
REMOTE CONTROLLER SPECIFICATIONS
Model
PERFORMANCE FEATURES
RG35A(2)/BG(C)EF, RG35A1/BG(C)EF, RG35B/BG(C)E, RG35C/BG(C)E,
RG36A(1)/BG(C)EF, RG36A2/BG(C)EF, RG36B(1)/BG(C)E, RG36C/BG(C)E
Rated Voltage
3.0V (Dry cell batteries R03/LR03 x 2)
Signal Receiving Range
8m (when using 3.0 voltage, up to 11m)
Environment
-5ºC ~ 60ºC
RG36A2/BG(C)EF
RG36B(1)/BG(C)E
RG36C/BG(C)E
ON/OFF
O N /OF F
ON/OF F
ON /O FF
TEM P
T EMP
TE MP
RG36A(1)/BG(C)EF
PERFORMANCE FEATURES
TE MP
1. Operating Mode: AUTO, COOL, DRY, HEAT (Cooling only model without), and FAN.
2. Timer Setting Function in 24 hours.
MO DE
SHORT
CUT
MODE
S HORT
CUT
MODE
S HORT
CUT
MODE
SHORT
C UT
S WING
FAN
SPE ED
SWING
FAN
SPEE D
SWING
FAN
SPEED
SWIN G
F AN
SP EED
DIRECT
TIME R
ON
DIR ECT
TIMER
ON
D IRE CT
TI MER
ON
DIRECT
TIMER
ON
S LEEP
F RESH
TIMER
OFF
SLEEP
TIMER
OFF
S LEEP
TIME R
OFF
SLEEP
TIMER
O FF
TURB O
SEL F
CLEAN
LED
FOLL OW
ME
T URBO
LED
TU RBO
FP
L ED
3. Indoor Setting Temperature Range : 17ºC~30ºC.
4. Full function of LCD (Liquid Crystal Display).
RG35A(2)/BG(C)EF
RG35A1/BGEF
RG35B/BG(C)E
RG35C/BG(C)E
L OC K
RE SE T
L OCK
RES ET
LO CK
RES ET
LOC K
RE SE T
Models of RG36B/BG(C)E do
not have FP function.
MO DE
SH OR TCUT
MO DE
SHO RTC UT
MODE
SHORTCUT
M ODE
SHO RTCUT
SW ING
TEM P
FA N
SPEED
SW ING
TEMP
FAN
SP EED
SWING
TEMP
FAN
SPEED
SWING
TEMP
FA N
SPEED
DIRECT
TIMER
ON
TIMER
OF F
DI RECT
TIMER
ON
TIMER
OFF
DI RECT
TIMER
ON
TI MER
OFF
D IRE CT
TIMER
ON
TIMER
OFF
SLEEP
FRESH
TURBO
SELF CLEAN
SLEEP
TURBO
FP
SLEE P
TURBO
LED
RESET
L ED
FO LLO W ME
LOCK
R ESET
LED
FO LLO W ME
LOCK
RE SET
LOCK
SLEEP
NOTE: There is only a slight difference in appearance
between the RG35 series and RG36 series. The operations
and functions of the buttons are the same. Some buttons
have two functions, some buttons have only one function,
.
for example SLEEP and
FRESH
RE SE T
SLEEP
LO CK
Please refer to the above illustrations for details.
4
E963_Lennox AC Remote Controller 20pp A5_1c.indd 4-5
5
13/12/11 4:56 PM
FUNCTION BUTTONS
FUNCTION BUTTONS
1 ON/OFF Button (
ON/OFF
)
8 UP Button (
Operation starts when this button is pressed and stops when
this button is pressed again.
2 MODE Button
9 DOWN Button (
1
Each time the button is pressed, the operation mode is
selected in the following sequence:
8
9
ON/OFF
TEMP
AUTO
1
MODE
SHOR TCUT
2
SWING
T EMP
F AN
SP EED
DIRECT
T IMER
ON
TIMER
OFF
SLEEP
FRESH
TUR BO
SELF C LEAN
3
4
LED
FOL LOW M E
5
RESET
6
LOCK
COOL
DRY
HEAT
FAN
8
NOTE: Heat mode is for Cooling & Heating models only.
10
9
11
12
13
3 SWING Button
14
4 DIRECT Button
15
7
RG35A(2)
Used to stop or start horizontal louvre auto swing feature.
Used to change the louvre movement and set the desired up/
down air flow direction. The louvre changes 6º in angle for
each button press.
2
MO D E
S HO RT
CU T
3
SW ING
FA N
S PE E D
4
DIR EC T
TI ME R
ON
12
5
SLE EP
FR E SH
TIME R
OFF
13
6
TU RB O
S ELF
C L EA N
LED
FOLLOW
ME
14
10
11
7
LOC K
RESET
15
RG36A(1)
5 SLEEP/FRESH Button
Active/Disable SLEEP function. If pressing for more than 2
seconds, the FRESH function will be activated. Pressing for
more than 2 seconds again will disable it.
NOTE: While the unit is running under SLEEP mode, it would
be cancelled if the MODE, FAN SPEED or ON/OFF buttons
are pressed.
8
M ODE
SHORT CUT
2
S WING
TEMP
FA N
SPEED
D IRECT
TIM ER
ON
T IMER
OFF
S LEEP
TURB O
FP
3
4
LED
FOLL OW ME
5
6
RESET
LOCK
14
15
7
6
10
9
11
12
13
RG35A1
E963_Lennox AC Remote Controller 20pp A5_1c.indd 6-7
Active/Disable TURBO function. If pressing for more than
2 seconds, the SELF-CLEAN function will be activated.
Pressing for more than 2 seconds again to disable
(depending on model). During the heating operation (only
when the setting mode is HEAT), press this button and the
unit will operate at a setting temperature of 8°C.The display
window of indoor unit will display FP. Pressing ON/OFF,
SLEEP, FP, MODE, FAN SPEED, UP, DOWN and SHORTCUT
while operating will cancel the FP function.
7 RESET Button:
When you press the recessed RESET button, all current
settings are cancelled and the control will return to the initial
settings.
-)
Press this button to decrease setting temperature or to
decrease the Hour setting during Timer setting.
10 SHORTCUT (MEMORY SHORTCUT) Button
• Used to restore the current settings or restore previous
settings.
• On the first time connecting to power, if the SHORTCUT
button is pressed, the unit will operate on AUTO mode,
24°C, and fan speed will be set to Auto.
• Pressing this button whilst the remote controller is on,
the system will automatically revert back to the previous
settings including operating mode, setting temperature,
fan speed level and sleep feature (if activated).
• Pressing this button whilst the remote controller is off,
the system will only resume the previous settings and
will not transmit the signals to the unit. The sleep feature
is disabled.
• If pressing for more than 2 seconds, the system will
automatically restore the current operation settings
including operating mode, setting temperature, fan speed
level and sleep feature (if activated).
1
11 FAN SPEED Button
8
9
ON/OFF
6 TURBO/SELF-CLEAN (or FP) Button:
1
+)
Press this button to increase setting temperature or to
increase the Hour setting during Timer setting.
TEMP
2
MO D E
S HO RT
CU T
3
SW ING
FA N
S PE E D
4
DIR EC T
TI ME R
ON
12
5
SLE EP
TIME R
OFF
13
6
7
TU RB O
FP
LED
14
LOC K
RESET
RG36B1
Used to select the fan speed in four steps:
AUTO
LOW
MED
HIGH
10
11
12 TIMER ON Button
Pressing this button will initiate the auto-on time sequence.
Each press will increase the auto-timed setting in 30
minutes increments.
When the setting time displays 10H, each press will increase
the auto-timed setting in 60 minute increments. To cancel
the auto-timed program, simply adjust the auto-on time to
0:0.
15
7
13/12/11 4:56 PM
FUNCTION BUTTONS (continued)
INDICATORS ON LCD
13 TIMER OFF Button
Transmission Indicator
Press this button to initiate the auto-off time sequence.
Each press will increase the auto-timed setting in 30 minute
increments.When the setting time displays 10H, each press
will increase the auto-timed setting in 60 minute increments.
To cancel the auto-timed program, simply adjust the auto-off
time to 0:0
1
8
9
ON/OF F
T EMP
2
10
MODE
SH ORT
CUT
3
SWING
FAN
S PEED
4
DIRE CT
TI MER
ON
12
5
SLEEP
FRESH
T IME R
OFF
13
6
TU RBO
SELF
CLE AN
LED
FOLLOW
ME
14
11
7
LO CK
R ES ET
15
This transmission indicator lights when remote controller
transmits signals to the indoor unit.
Mode display
Displays the current operation mode. Including auto ( ),
cool ( ), dry ( ), heat ( ) (Not applicable to cooling only
models), fan ( ) and back to auto ( ).
14 LED/FOLLOW ME Button
Disable/Active indoor screen Display. When pressing for
more than 2 seconds, the FOLLOW ME function will be
activated. Pressing for more than 2 seconds again will
disable it.
15 LOCK Button
When you press the recessed LOCK button, all current
settings are locked in and the remote controller does not
accept any operation except that of the LOCK. Press again to
cancel the LOCK mode.
auto cool dry
heat
fan
Displays the temperature setting (17ºC~30ºC). When you
set the operating mode to FAN, no temperature setting is
displayed. In the TIMER mode, display shows the ON and
OFF settings of the TIMER.
SET TEMP. TIMER ONOFF
Fan speed display
Displays the selected fan speed, AUTO (no display) and three
fan speed levels “ ” (LOW) “ ” (MED) “ ”(HIGH) can be
indicated. The fan speed is AUTO when the operating mode
is either AUTO or DRY.
NOTE:
• Button designs shown may be slightly different from
the actual one you purchased depending on individual
models.
• All the functions described above are related to the
indoor unit. If the indoor unit does not have this feature,
then nothing will happen when that button on the remote
controller is pressed.
Temp./Timer display
ON/OFF display
sleep follow me lock
run
Displayed by pressing the ON/OFF button once.
Press the ON/OFF button again to remove.
Lock Display
Displayed when LOCK mode is activated.
FOLLOW ME Display
Displayed when FOLLOW ME function is activated.
Sleep Display
Displayed under sleeping operation.
Press the SLEEP button again to remove.
NOTE:
All indicators shown in the figure are for the purpose of clear
presentation. During the actual operation only the relative
functional signs are shown on the display window.
8
E963_Lennox AC Remote Controller 20pp A5_1c.indd 8-9
9
13/12/11 4:56 PM
HOW TO USE THE BUTTONS
3
2
M ODE
SHORTCUT
1
SWING
TEM P
FAN
SP EED
DIRECT
TIMER
ON
TIMER
OFF
SLEEP
F RESH
TURBO
SELF CL EAN
RES ET
2
HOW TO USE THE BUTTONS
Auto operation
Dehumidifying operation
Ensure the unit is plugged in and power is on. The
OPERATION indicator on the display panel of the indoor unit
starts flashing.
Ensure the unit is plugged in and power is on. The
OPERATION indicator on the display panel of the indoor unit
starts flashing.
1. Press the MODE button to select Auto.
1. Press the MODE button to select DRY mode.
2. Press the UP/DOWN button to set the desired
temperature. The temperature can be set within a range
of 17ºC~ 30ºC in 1ºC increments.
2. Press the UP/DOWN buttons to set the desired
temperature. The temperature can be set within a range
of 17ºC~ 30ºC in 1ºC increments.
3. Press the ON/OFF button to start the air conditioner.
3. Press the ON/OFF button to start the air conditioner.
NOTE:
1. In the Auto mode, the air conditioner can logically choose
the mode of Cooling, Fan, and Heating by sensing the
difference between the actual ambient room temperature
and the setting temperature on the remote controller.
2. In the Auto mode, you cannot change the fan speed. It
has already been automatically controlled.
LED
FOLLOW ME
3. If the Auto mode is not comfortable, the desired mode
can be selected manually.
LO CK
3
2
MODE
SHORTCUT
1
SWING
TEMP
FA N
SPEED
DIRECT
TIMER
ON
TIMER
OF F
SLEEP
FRESH
T URBO
SELF CLEAN
RESE T
LED
FOLLOWME
LOC K
2
NOTE:
In the Dehumidifying mode, you cannot change the fan
speed. It has already been automatically controlled.
Adjusting air flow direction
Use the SWING and DIRECT button to adjust the desired
airflow direction.
1. When pressing the DIRECT button, the horizontal louvre
changes 6 degree in angle for each press.
Cooling /Heating/Fan operation
2. When pressing the SWING button, the louvre will swing
up and down automatically.
Ensure the unit is plugged in and power is on.
1. Press the MODE button to select COOL, HEAT (cooling &
heating models only) or FAN mode.
2. Press the UP/DOWN buttons to set the desired
temperature.
NOTE:
When the louvre swings or moves to a position which would
affect the cooling or heating effect of the air conditioner, it
will automatically change the swing/moving direction.
3. Press the FAN button to select the fan speed in four
steps - Auto, Low, Med, or High.
4. Press the ON/OFF button to start the air conditioner.
4
M ODE
SHORTCUT
2
1
SWING
TEM P
FAN
SP EED
DIRECT
TIMER
ON
TIMER
OFF
SLEEP
F RESH
TURBO
SELF CL EAN
RES ET
2
3
NOTE:
In the FAN mode, the setting temperature is not displayed
in the remote controller and you are not able to control the
room temperature either. In this case, only steps 1, 3 and 4
may be performed.
LED
FOLLOW ME
LO CK
10
E963_Lennox AC Remote Controller 20pp A5_1d.indd 10-11
11
14/12/11 11:57 AM
HOW TO USE THE BUTTONS
HOW TO USE THE BUTTONS
Timer operation
Press the TIMER ON button can set the auto-on time of the
unit. Press the TIMER OFF button can set the auto-off time
of the unit.
CAUTION
The effective operation time set by the remote controller for the timer function is limited to the following settings: 0.5, 1.0,
1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20,
21, 22, 23 and 24.
To set the Auto-on time
1. Press the TIMER ON button. The remote controller shows
TIMER ON, the last Auto-on setting time and the signal
“h” will be shown on the LCD display area. Now it is
ready to reset the Auto-on time to START the operation.
M ODE
TEMP
FAN
SPEED
DIRECT
TIM ER
ON
TIMER
OFF
SLEEP
F RESH
TURBO
SELF CLEAN
RESE T
LED
FOLLOW ME
TIMER ON
TIMER OFF
2. Push the TIMER ON button again to set desired Auto-on
time. Each time you press the button, the time increases
by half an hour between 0 and 10 hours and by one hour
between 10 and 24 hours.
SH ORTCUT
SWING
Example of Timer Setting
1
2
3. After setting the TIMER ON there will be a one second
delay before the remote controller transmits the signal
to the air conditioner. Then, after approximately another
2 seconds, the signal “h” will disappear and the set
temperature will re-appear on the LCD display window.
Start
Off
Stop
LOC K
On
To set the Auto-off time
1. Press the TIMER OFF button. The remote controller
shows TIMER OFF, the last Auto-off setting time and the
signal “h” will be shown on the LCD display area. Now it
is ready to reset the Auto-off time to stop the operation.
2. Push the TIMER OFF button again to set desired Auto-off
time. Each time you press the button, the time increases
by half an hour between 0 and 10 hours and by one hour
between 10 and 24 hours.
3. After setting the TIMER OFF there will be a one second
delay before the remote controller transmits the signal
to the air conditioner. Then, after approximately another
2 seconds, the signal “h” will disappear and the set
temperature will re-appear on the LCD display window.
TIMER OFF (Auto-off Operation)
The TIMER ON feature is useful when you want the unit
to turn on automatically before you return home. The air
conditioner will automatically start operating at the set time.
The TIMER OFF feature is useful when you want the unit to
turn off automatically after you go to bed. The air conditioner
will stop automatically at the set time.
Example:
Example:
To start the air conditioner in 6 hours.
To stop the air conditioner in 10 hours;
1. Press the TIMER ON button, the last setting of starting
operation time and the signal
1. Press the TIMER OFF button, the last setting of stopping
operation time and the signal “h” will show on the display
area.
3. Wait for 3 seconds and the digital display area will show
the temperature again. The“TIMER ON” indicator remains
on and this function is activated
E963_Lennox AC Remote Controller 20pp A5_1c.indd 12-13
10 hours later
TIMER ON (Auto-on Operation)
2. Press the TIMER ON button to display “6:0h” on the
TIMER ON display of the remote controller.
12
Set
6 hours later
2. Press the TIMER OFF button to display “10h” on the
TIMER OFF display of the remote controller.
3. Wait for 3 seconds and the digital display area will
show the temperature again. The “TIMER OFF” indicator
remains on and this function is activated.
13
13/12/11 4:56 PM
HOW TO USE THE BUTTONS
HOW TO USE THE BUTTONS
Example of Timer Setting
SLEEP / FRESH function
• Pressing this button for less than 2 seconds will initiate the
SLEEP function. Keep pressing this button for more than 2
seconds and the FRESH function is initiated.
TIM ER ON OFF
TIMER ON OFF
• The sleep function enables the unit to automatically increase
(cooling) or decrease (heating) by 1ºC per hour for the first
two hours, then hold steady for the next 5 hours. After that
the unit will cease operation. It is able to maintain the most
comfortable temperature and save energy.
Start
MODE
Start
Stop
Off
Stop
NOTE: The SLEEP function is only available under Cooling,
Heating and AUTO operations.
SHORTCUT
SW ING
TEMP
FA N
SPEED
DIRECT
TIMER
ON
TIMER
OFF
SLEEP
FRESH
T URBO
SELF CLEAN
• When the FRESH function is initiated, the Ionizer/Plasma Dust
Collector (depending on models) is energized and will help to
remove pollen and impurities from the air.
On
Set
2 hours later
after setting
10 hours later
after setting
Set
2 hours later
after setting
5 hours later
after setting
LED
FOLLOW ME
1
RE SET
COMBINED TIMER
(Setting both ON and OFF timers simultaneously)
TIMER OFF
(On
Stop
TIMER ON
Start operation)
This feature is useful when you want to stop the air
conditioner after you go to bed, and start it again in the
morning when you wake up or when you return home.
Example:
To stop the air conditioner 2 hours after setting and start it
again 10 hours after setting.
1. Press the TIMER OFF button.
2. Press the TIMER OFF button again to display 2.0h on the
TIMER OFF display.
3. Press the TIMER ON button.
4. Press the TIMER ON button again to display 10h on the
TIMER ON display
5. Wait for 3 seconds and the digital display area will show
the temperature again. The “TIMER ON OFF” indicator
remains on and this function is activated.
14
E963_Lennox AC Remote Controller 16pp A5_2.indd 14-15
LOCK
TIMER ON TIMER OFF
(Off
Start
1
Stop operation)
LED / FOLLOW ME function
This feature is useful when you want to start the air
conditioner before you wake up and stop it after you leave
the house.
• Pressing this button for less than 2 seconds will initiate LED
function. Keep pressing this button for more than 2 seconds
and the FOLLOW ME function is initiated.
Example:
• When the FOLLOW ME function is activated, the remote
display is actual temperature at its location. The remote
control will send this signal to the air conditioner every 3
minutes until the FOLLOW ME button is pressed again.
To start the air conditioner 2 hours after setting, and stop it 5
hours after setting.
• The FOLLOW ME function is not available under DRY and FAN
mode.
1. Press the TIMER ON button.
2. Press the TIMER ON button again to display 2.0h on the
TIMER ON display.
MODE
• Switching the operation mode or turning off the unit will
cancel the FOLLOW ME function automatically.
SHORTCUT
3. Press the TIMER OFF button.
4. Press the TIMER OFF button again to display 5.0h on the
TIMER OFF display .
5. Wait for 3 seconds and the digital display area will show
the temperature again. The “TIMER ON OFF” indicator
remains on and this function is activated.
SWING
TEMP
FAN
SPEE D
DIRE CT
TIMER
ON
TIMER
OFF
SLEE P
FRES H
TURBO
SELF CLEAN
2
NOTE: The timer setting (TIMER ON or TIMER OFF) that in
sequence occurs directly after the set time will be activated
first.
• Pressing this button for less than 2 seconds will initiate
TURBO function. Pressing this button for more than 2
seconds, the SELF-CLEAN function is initiated.
LED
FOLLOW ME
1
RESET
TURBO / SELF-CLEAN function
L OCK
2
• Turbo function enables the unit to reach the preset
temperature in the shortest possible time. When pressing
this button on cooling mode, the unit will blow strong cooling
air with super high fan speed. When pressing this button on
heating mode (applicable to the unit adopts PTC only), the
PTC will be energized and bring fast heating operation.
• Under SELF-CLEAN mode, the air conditioner will
automatically clean and dry the evaporator keeping it as
fresh for the next operation.
15
21/12/11 10:07 AM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement