Cypress CH-506RX Specifications

CMSI-4H4CV
HDBaseT™ 4×4 HDMI Matrix over CAT5e/6/7
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer file, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2011 by Cypress Technology.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
•
Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
•
To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
•
Never spill liquid of any kind on or into this product.
•
Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
•
Do not attach the power supply cabling to building surfaces.
•
Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
•
Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
•
To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO.
DATE DD/MM/YY SUMMARY OF CHANGE
VR0
13/11/12
Preliminary Release
VR1
04/06/13
RS-232 & Telnet's Set IP Command
VS1
04/11/13
Separated 4x4 and 8x8 Manuals
CONTENTS
1. Introduction�������������������������������������������� 1
2. Applications������������������������������������������� 1
3. Package Contents�������������������������������� 1
4. System Requirements���������������������������� 2
5. Features�������������������������������������������������� 2
6. Operation Controls and Functions������� 3
6.1 Front Panel�����������������������������������������3
6.2 Rear Panel�����������������������������������������4
6.3 Side Panel������������������������������������������5
6.4 Remote Control���������������������������������6
6.5 IR Cable Pin Assignment������������������7
6.6 RS-232 Pin Assignment����������������������7
6.7 RS-232 and Telnet Commands��������8
6.8 Telnet Control������������������������������������9
6.9 Web GUI Control�����������������������������11
7. Connection Diagram�������������������������� 14
8. Specifications�������������������������������������� 15
8.1 Technical Specifications����������������15
8.2 CAT5e/6/7 Cable Specification����16
9. Acronyms��������������������������������������������� 16
1. INTRODUCTION
The HDBaseT™ 4 by 4 HDMI Matrix over CAT5e/6/7 supports
the transmission of video (resolutions up to 1080p Full HD and
1920×1200@60Hz) and multi-channel digital audio from four high
definition sources to four outputs over a single CAT5e/6/7 cable (up
to 100m) for each output. It supports high resolution digital audio
formats such as LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTSHD Master Audio as well as 3D content that can be displayed when
connecting a 3DTV and 3D source. The matrix can be controlled
via IR, RS-232, Telnet or Web GUI. Power over Ethernet (PoE) support
means that compatible receivers do not need their own seperate
power supplies, allowing for greater flexibility in installations.
2. APPLICATIONS
• HDMI Matrix System
• Video/TV wall display and control
• Security surveillance and control
• Commercial advertising, display and control
• University lecture hall, display and control
• Retail sales and demonstration
3. PACKAGE CONTENTS
• 1×HDBaseT ™ 4×4 HDMI Matrix over CAT5e/6/7
• 2×IR Extender
• 2×IR Blaster
• 1×IR Remote Control
• 2×24 V/6.25 A DC Power Adaptor (1 for PoE)
• Operation Manual
1
4. SYSTEM REQUIREMENTS
• HDMI equipped source devices, connect with HDMI cables or DVI
equipped source, connect with DVI to HDMI cables
• HDMI equipped displays (TVs or monitors) or HDMI equipped AV
receivers, connected with HDMI cables
• Industry standard CAT5e/6/7 cables
• HDBaseT™ Receivers (CH-506RX, CH-507RX or CH-1109RX)
5. FEATURES
• HDMI, HDCP1.1 and DVI compliant
• Supports HDMI 3D features
• Supports resolutions VGA~WUXGA and 480i~1080p dependent upon
the output display’s EDID settings
• Supports 3D signal display dependent upon the output display EDID
settings
• Supports PoE (Power over Ethernet) on compatible receivers only
• Supports HDMI input up to 15 meters at 8-bit resolution or 10 meters
at 12-bit resolution
• Supports bi-directional IR to and from input and output locations
• Supports control via RS-232, IR remote, on-panel buttons and IP
(Telnet & Web GUI)
• 2U size design
• Supports external and internal EDID settings
• Supports LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD
Master Audio transmission
Note:
1. The PoE function is designed for powering compatible receiver
units only—non-PoE receivers will need their own power supply.
Receivers of another brand may not be compatible.
2. Do not connect the LAN/CONTROL port to CAT outputs of this
device.
2
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
MENU
POWER
A
B
C
D
OUT
E1
2
3
4
IN
LOCK
4X4 HDMI MATRIX over CAT5e/6 CMSI-4H4CV
1
2
3
4
5
6
1 LCM: Displays the setting information of each input and output
setting.
2 POWER: Press this button to power the device on/off. The LED will
illuminate green when the power is on, red when it is in 'Standby'
mode.
3 LOCK: Press this button to lock all the buttons on the panel; press
again to unlock. The LED will illuminate green when locked.
4 IR: IR Receiver window (accepts the remote control signal of this
device only) with IR frequency of 38 kHz.
5 MENU: Press this button to access the LCM menu system, from
here EDID settings can be managed and IP system settings are
displayed.
6 1~4/A~D and OUT/IN: Press the OUT or IN button to select the
output or input mode and then press the required number button
to make the selection accordingly.
For example, if outputs A~B need to be set to input 1 and outputs
C~D need to be set to input 2, then the following sequence of
button presses need to be performed:
Press: OUTABIN1MENU,
and then press: OUTCDIN2MENU.
Note: If the MENU button is not pressed the selection will not be
changed.
3
6.2 Rear Panel
7
6
3
GND
ALL
IR OUT
IR OUT
IR IN
IR IN
A
IR OUT
IR OUT
CAT5e/6 OUT
CAT5e/6 OUT
CONTROL
B
C
IR OUT
CAT5e/6 OUT
IR IN
IR IN
D
V+
GND
2
1
4
3
+V
GND
CAT5e/6 OUT
POE 24V
IR IN
RS232
SERVICE
1
HDMI IN
1
2
4
5
8
2
HDMI IN
3
HDMI IN
4
HDMI IN
9
MAIN 24V
10
11
1 CONTROL: This port is the link for Telnet or Web GUI controls, connect
to an active Ethernet link with an RJ45 terminated cable (for further
details on IP control, please refer to sections 6.8 & 6.9).
Warning: Please do not connect this port directly to the PC/Laptop as the
Telnet function will not work.
2 RS-232: Connect to a PC or control system with D-Sub 9-pin cable
for control of the matrix via RS-232 commands (please refer to
Section 6.7 for a list of commands).
3 ALL IR OUT: Connect to the IR blaster for IR signal transmission to the
source devices. Place the IR blaster in direct line-of-sight of the
equipment to be controlled. All signals received from the display
side will be relayed to the source devices.
4 ALL IR IN: Connect to the IR extender for IR signal reception. Ensure
that the remote being used is within the direct line-of-sight of the IR
extender. It will transmit all signals received through the IR ALL OUT.
5 SERVICE: Manufacturer use only.
6 IR OUT A~D: Connect to the IR blasters for IR signal transmission.
Place the IR blaster in direct line-of-sight of the equipment to be
controlled. It will transmit the IR signal received from the receiver
side according to the selected input.
7 IR IN 1~4: Connect to the IR extenders for IR signal reception. Ensure
that the remote being used is within the direct line-of-sight of the
IR extender. It will send out the IR signal received to the selected IR
OUT (A-D).
8 CAT5e/6/7 OUT A~D: Connect the CAT outputs to the CAT input port
of the receiver units with a single CAT5e/6/7 cable for HDMI Audio/
Video and IR control signal transmission.
Warning: Please do not connect the CAT5e/6/7 outputs to the
receiver's LAN port.
4
9 HDMI IN 1~4: Connect to the HDMI source devices such as a DVD
player or a Set-top Box with HDMI cables or DVI to HDMI cables.
10 DC 24V: Connect the 24 V DC power supply to the unit and plug the
adaptor into an AC outlet.
11 PoE 24V: Connect the 24 V PoE power supply into the unit and plug
the adaptor into an AC outlet. This unit will mainly power PoE (Power
over Ethernet) capable receiver units.
6.3 Side Panel
1
1 Fan Ventilator: These are air ventilation areas, DO NOT block these
areas or cover it with any object. Please allow adequate space
around the unit for air circulation.
5
6.4 Remote Control
1 POWER: Press this button to switch
the device 'ON' or set it to standby
1
mode.
2 IN: Input selection 1~4.
3 OUT: Output selection A~D.
Note:
1. When the IR remote is used in the
Output Zone the user only needs
to select the desired input (1~8)
2
3
2. 5~8 and E~H buttons are not
functioning.
6
6.5 IR Cable Pin Assignment
IR Blaster
1
Power 5 V
2
IR Blaster Signal
3
NC
1
IR Signal
2
Power 5 V
3
Ground
IR Extender
6.6 RS-232 Pin Assignment
HDMI MATRIX
PIN
Assignment
PIN
Assignment
1
NC
1
NC
2
Tx
►
2
Rx
3
Rx
◄
3
Tx
4
NC
4
NC
5
GND
5
GND
6
NC
6
NC
7
NC
7
NC
8
NC
8
NC
9
NC
9
NC
Baud Rate: 19200 bps
Data Bit: 8-bit
Parity: None
Stop Bit: 1-bit
Flow Control: None
7
REMOTE CONTROL CONSOLE
6.7 RS-232 and Telnet Commands
COMMAND
DESCRIPTION
A1~A4
Switch Output A to 1~4
B1~B4
Switch Output B to 1~4
C1~C4
Switch Output C to 1~4
D1~D4
Switch Output D to 1~4
ABCD…1~ABCD…4
Switch Output ABCD… to 1~4 at the
same time
SETIP <IP> <SubNet> <GW>
Setting IP. SubNet. GateWay<Static IP>
RSTIP
IP configuration was reset to factory
defaults<DHCP>
IPCONFIG
Display the current IP config
P0
Power Off
P1
Power On
I1~I4
Switch all the output to 1~4
ST
Display the current matrix state and
firmware version
RS
System Reset to D4
EM
Setting EDID MODE. 1-STD 2-TV.
?
Display all available commands
QUIT
Exit (Telnet only)
Note:
1. Commands will not be executed unless followed by a carriage
return. Commands are case-insensitive.
2. When the Telnet connection is idle for 10 minutes it will be
automatically disconnected.
3. The TV EDID setting will always follow output port 1's EDID setting
regardless of the output change.
4. EDID setting switching will execute immediately.
8
6.8 Telnet Control
Before attempting to use the telnet control, please ensure that both
the Matrix (via the 'LAN /CONTROL' port) and the PC/Laptop are
connected to the same active networks.
To access the telnet control in Windows 7, click on the 'Start' menu
and type "cmd" in the Search field then press enter.
Under Windows XP go to the 'Start' menu and click on "Run", type
"cmd" with then press enter.
Under Mac OS X, go to Go→Applications→Utilities→Terminal
See below for reference.
9
Once in the command line interface (CLI) type "telnet", then the IP
address of the unit and "23", then hit enter.
Note: The IP address of the Matrix can be displayed on the device's
LCM monitor by pressing the Menu button twice.
This will bring us into the device which we wish to control. Type "HELP"
to list the available commands.
Type “IPCONFIG” To show all IP configurations. To reset the IP,
type “RSTIP” and to use a set static IP, type ”SETIP” (For a full list of
commands, see Section 6.7).
Note: Commands will not be executed unless followed by a carriage
return. Commands are not case-sensitive. If the unit's IP is changed
then the IP Address required for Telnet access will also change
accordingly.
10
6.9 Web GUI Control
On a PC/Laptop that is connected to the same active network as the
Matrix, open a web browser and type the device's IP address on the
web address entry bar. The browser will display the device's status,
control and User setting pages.
Click on the 'Control' tab to control power, input/output ports, EDID
and reset mode.
11
Clicking on the 'User Setting' tab allows you to reset the IP
configuration. The system will ask for a reboot of the device when any
of the settings are changed. The IP address needed to access the
Web GUI control will also need to be changed accordingly on the
web address entry bar.
12
7. CONNECTION DIAGRAM
ZONE C
RX
Power
ZONE D
RX
Link
IR 2
IR 1
Extender Blaster
RS232 Out
CAT5e/6 In
Power
Link
IR 2
IR 1
Extender Blaster
RS232 Out
CAT5e/6 In
IR In (ALL)
Smartphone
or Tablet
ALL
LAN
IR OUT
IR OUT
IR IN
IR IN
A
IR OUT
B
CAT5e/6 OUT
CAT5e/6 OUT
CONTROL
IR IN
RS232
SERVICE
RS-232
Wireless Router
RS-232 Equipped
PC or Notebook
1.5m
60°
IR BLASTER
13
60°
3m
7m
m
3m
IR EXTENDER
IR Out (All)
1
HDMI IN
2
HDMI IN
1
2
ZONE E
ZONE F
Displays
HDMI Outputs
IR In/Out
RX
Power
RX
Link
IR 2
IR 1
Extender Blaster
RS232 Out
CAT5e/6 In
Power
Receiver Units
Link
IR 2
IR 1
Extender Blaster
RS232 Out
CAT5e/6 In
CAT5e/6/7
Cable (100m)
GND
IR OUT
C
IR OUT
CAT5e/6 OUT
IR IN
D
V+
GND
2
1
4
3
+V
GND
CAT5e/6 OUT
POE 24V
IR IN
Power Supply for
Power-over-Ethernet
3
HDMI IN
4
HDMI IN
3
4
MAIN 24V
Main Power Supply
HDMI Inputs
IR Out/In
Source
Equipment
14
8. SPECIFICATIONS
8.1 Technical Specifications
Video Bandwidth
225 MHz/6.75 Gbps
Input Ports
4×HDMI, 5×IR Extender, 1×RS-232, 1×RJ45 (Control), 1×Mini USB Type B (For
firmware updated only)
Output Ports
4×CAT5e/6/7, 5×IR Blaster
IR Frequency
30~50 kHz
Supported Resolutions
HDTV: 480i~1080p50/60 & 1080p24
PC: VGA~WXGA
HDMI Input Cable Length
15 m (1080p@8-bit)
10 m (1080p@12-bit)
Audio Sampling Rate
Up to 192 kHz
ESD Protection
Human-body Model:
± 8kV (Air-gap discharge)
± 4kV (Contact discharge)
Power Supply
24 V/6.25 A DC (US/EU standards, CE/
FCC/UL certified)
Dimensions
438 mm (W)×255 mm (D)×93 mm (H)
Weight
4238 g
Chassis Material
Metal
Color
Black
Operating Temperature
0 ºC~40 ºC/32 ºF~104 ºF
Storage Temperature
−20 ºC~60 ºC/−4 ºF~140 ºF
Relative Humidity
20~90 % RH (non-condensing)
Power Consumption
42 W/TX (Main), 27 W/RX (PoE)
15
8.2 CAT5e/6/7 Cable Specification
CABLE
RANGE
TYPE
CAT5e/6/7
100 m
PIXEL
CLOCK
VIDEO
DATA
RATE
RATE
≤225 MHz
≤5.3 Gbps
SUPPORTED VIDEO
Up to 1080p, 60 Hz,
(HD Video) 36 bits, 3D (data
rates lower than 5.3
Gbps or below 225
MHz TMDS clock).
70 m
>225 MHz
> 5.3 Gbps
4K×2K, 30 Hz video
(Ultra HD
formats
Video)
9. ACRONYMS
ACRONYM
COMPLETE TERM
CLI
Command Line Interface
DTS
Digital Theater System
DVI
Digital Visual Interface
EDID
Extended Display Identification Data
GUI
Graphical User Interface
HDCP
High-bandwidth Digital Content Protection
HDMI
High-Definition Multimedia Interface
HDTV
High-Definition Television
LCM
Liquid Crystal Module
USB
Universal Serial Bus
VGA
Video Graphics Array
WUXGA
Widescreen Ultra Extended Graphics Array
16
CYPRESS TECHNOLOGY CO., LTD
Home page: http://www.cypress.com.tw
20120518 MPM-CMSI8H8CV