Audiovox | ACC-31 | INSTALLATION MANUAL MODEL ACC-31 6

MODEL ACC-31
6-DISC CD CHANGER WITH
WIRED COMMANDER
COMPACT
DIGITAL AUDIO
INSTALLATION MANUAL
PACKING LIST
MAIN UNIT
CD Changer
ACC31
DIGITAL AUDIO 6 DISC
COMPACT DISC CHANGER
BY AUDIOVOX
INSTALLATION PARTS
Changer Mounting Brackets
Self-tapping screw
(M5 x 12),
w/Lockwashers
Phillips Hex -Head
Bolt (Small), w/Flat
Washers and Lockwashers
8 pcs. each
6 pcs. each
R
L
1 each
Floor Mounting Brackets
Screw Hole Cover Labels
5 Meter Din Cable
1 pc.
L
1 each
1 pc.
R
ACCESSORIES
CD Magazine
P/N:ACC31MAZ
1 pc.
2
Index seal sheet
Installation Manual
Owner's guide
1 pc.
1 pc.
1 pc.
BEFORE INSTALLING THE UNIT
Transport Lock Screws
The mechanism in the CD changer is "locked" into place during
shipment by the 4 transport screws, two on each side. Be sure to remove
the screws prior to installation. Retain these screws for future use when
transporting the unit for service/maintenance.
CAUTION
After removing the transport lock screws, place the supplied seals over
the screw holes. These seals are used to keep dust out of the unit, which
could cause a malfunction.
Installation and Wiring Precautions
1
To prevent a short-circuit,
l Be sure to turn off the ignition and remove the negative (-) battery cable, prior to installation.
l Connect power wires last.
NOTE
If the changer is to be installed in a car that is equipped with an on-board drive or navigation computer, do not disconnect
the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution
during installation not to cause a short circuit.
2
Do not install the unit in the following locations:
l Locations exposed to direct sunlight.
l Where hot air is discharged from the car heater.
l In areas subject to extreme temperatures.
3
Incorrect installation can cause the CD Changer sound to "skip" when playing
a disc. Mount the unit firmly in place, using the supplied brackets and screws.
4
5
Be careful not to damage the car wiring.
6
l This unit cannot be installed on its side, end, or upside down. Installation in such positions will cause malfunctioning
of the mechanism.
l Be sure to use the supplied screws.
l Be careful not to snag any wires when tightening screws.
l Do not use any of the screws that are part of the brake or steering system to install the unit.
3
INSTALLATION
The unit can be installed horizontally (position H), or vertically at a 90° angle (position V). The position of the built-in anti-vibration
springs (left and right side), must correspond to the mounting position chosen. If the springs are not set correctly for the type of
installation chosen, the anti-vibration compensation will not be effective and vibration may cause the disc to skip.
HORIZONTAL INSTALLATION
Set the anti-vibration springs to
position "H".
POSITION
"H"
VERTICAL INSTALLAITON
Set the anti-vibration springs to
position "V".
POSITION
"V"
PROCEDURE FOR HORIZONTAL INSTALLATION
1
Attach a mounting bracket to each side of the unit, using the
hex head bolts and washers.
Hex head bolts
and washers
NOTE: Make sure anti-vibration springs
are set to position "H" as shown
above.
ACC31
DIG
ITA
COMP L AUDIO
ACT
DISC 6 DISC
CHAN
GER
BY AUD
IOVO
X
Bracket
2
Determine the mounting location and drill two mounting holes.
NOTE: If mounting surface is carpeted, use caution
when drilling holes to prevent drill bit from
catching on carpet. Cut holes in carpet
before drilling into sub-surface.
Carpet
WARNING
Never mount the unit near the fuel tank.
3
Drill holes 1/8" (4mm) in diameter.
Secure the unit in place, using two self-tapping Phillips head
screws.
Use RTV (silicone sealer) on screw threads or around
the holes to prevent moisture intrusion.
Self-tapping Phillips head screw
ACC31
DIG
ITA
COMP L AUDIO
ACT
DISC 6 DISC
CHAN
GER
BY AUD
IOVO
X
Bracket
4
Bracket
PROCEDURE FOR VERTICAL INSTALLATION
Note
If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 4), start with step 2.
1
Set the anti-vibration springs to position "V"
as shown below .
2
Attach a mounting bracket to each side of the unit, using
the hex head bolts and washers.
POSITION
"V"
Bracket
Bracket
Hex head bolt
and washer
3
Determine the mounting location and drill two mounting holes.
4
Mount the unit in place, using two self-tapping Phillips head
screws.
Use RTV (silicone sealer) on screw threads or around
the holes to prevent moisture intrusion.
NOTE: If mounting surface is carpeted, use caution
when drilling holes to prevent drill bit from
catching on carpet. Cut holes in carpet
before drilling into sub-surface.
Self-tapping
Phillips head
screw
WARNING
Never mount the unit near the fuel tank.
Bracket
Bracket
Carpet
Drill holes 1/8" (4mm) in diameter.
Hex head bolt
and washer
5
VEHICLE COMPONENT LAYOUT
NOTE: 1. Check with your Rampage/Audiovox audio dealer to
be sure your stereo is directly compatible with
this CD changer.
2. When used with Rampage Model AV-427 car
stereo, be sure Changer Selector switch on bottom
of radio chassis is set to position "B".
6
© 2000 Audiovox Electronics Corporation,
Happauge, N.Y. 11788
8
Printed in China
128-5943
Download PDF