Renesas H8/36109 User`s manual

REJ10J1319-0100
H8/36109 Group FP-100U
User System Interface Cable
HS36109ECH61H
User’s Manual
Renesas Microcomputer Development Environment System
H8 Family / H8/300H Tiny Series
HS36109ECH61HE
Rev.1.00
Revision Date: Apr. 06, 2006
Keep safety first in your circuit designs!
1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and
more reliable, but there is always the possibility that trouble may occur with them. Trouble with
semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate
measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or
(iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas
Technology Corp. product best suited to the customer's application; they do not convey any license
under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or
a third party.
2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any thirdparty's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or
circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and
algorithms represents information on products at the time of publication of these materials, and are
subject to change by Renesas Technology Corp. without notice due to product improvements or
other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or
an authorized Renesas Technology Corp. product distributor for the latest product information
before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising
from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corp. by various means,
including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data,
diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total
system before making a final decision on the applicability of the information and products. Renesas
Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the
information contained herein.
5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or
system that is used under circumstances in which human life is potentially at stake. Please contact
Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when
considering the use of a product contained herein for any specific purposes, such as apparatus or
systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.
6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in
whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must
be exported under a license from the Japanese government and cannot be imported into a country
other than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the
country of destination is prohibited.
8. Please contact Renesas Technology Corp. for further details on these materials or the products
contained therein.
IMPORTANT INFORMATION
READ FIRST
• READ this user's manual before using this emulator product.
• KEEP the user's manual handy for future reference.
Do not attempt to use the emulator product until you fully understand its mechanism.
Emulator Product:
Throughout this document, the term "emulator product" shall be defined as the following
products produced only by Renesas Technology Corp. excluding all subsidiary products.
• User system interface cable (HS36109ECF61H)
The user system or a host computer is not included in this definition.
Purpose of the Emulator Product:
This emulator product is a software and hardware development tool for systems employing the
Renesas microcomputer. This emulator product must only be used for the above purpose.
Limited Applications:
This emulator product is not authorized for use in MEDICAL, atomic energy, aeronautical or
space technology applications without consent of the appropriate officer of a Renesas sales
company. Such use includes, but is not limited to, use in life support systems. Buyers of this
emulator product must notify the relevant Renesas sales offices before planning to use the product
in such applications.
Improvement Policy:
Renesas Technology Corp. (including its subsidiaries, hereafter collectively referred to as
Renesas) pursues a policy of continuing improvement in design, performance, and safety of the
emulator product. Renesas reserves the right to change, wholly or partially, the specifications,
design, user's manual, and other documentation at any time without notice.
Target User of the Emulator Product:
This emulator product should only be used by those who have carefully read and thoroughly
understood the information and restrictions contained in the user's manual. Do not attempt to use
the emulator product until you fully understand its mechanism.
It is highly recommended that first-time users be instructed by users that are well versed in the
operation of the emulator product.
I
LIMITED WARRANTY
Renesas warrants its emulator products to be manufactured in
accordance with published specifications and free from defects in
material and/or workmanship. Renesas, at its option, will replace any
emulator products returned intact to the factory, transportation charges
prepaid, which Renesas, upon inspection, shall determine to be defective
in material and/or workmanship. The foregoing shall constitute the sole
remedy for any breach of Renesas’ warranty. See the Renesas warranty
booklet for details on the warranty period. This warranty extends only
to you, the original Purchaser. It is not transferable to anyone who
subsequently purchases the emulator product from you. Renesas is not
liable for any claim made by a third party or made by you for a third
party.
DISCLAIMER
RENESAS MAKES NO WARRANTIES, EITHER EXPRESS OR
IMPLIED, ORAL OR WRITTEN, EXCEPT AS PROVIDED
HEREIN, INCLUDING WITHOUT LIMITATION THEREOF,
WARRANTIES AS TO MARKETABILITY, MERCHANTABILITY,
FITNESS FOR ANY PARTICULAR PURPOSE OR USE, OR
AGAINST INFRINGEMENT OF ANY PATENT. IN NO EVENT
SHALL RENESAS BE LIABLE FOR ANY DIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR
LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE
EMULATOR PRODUCT, THE USE OF ANY EMULATOR
PRODUCT, OR ITS DOCUMENTATION, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES. EXCEPT AS
EXPRESSLY STATED OTHERWISE IN THIS WARRANTY,
THIS EMULATOR PRODUCT IS SOLD "AS IS ", AND YOU
MUST ASSUME ALL RISK FOR THE USE AND RESULTS
OBTAINED FROM THE EMULATOR PRODUCT.
II
State Law:
Some states do not allow the exclusion or limitation of implied warranties or liability for
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which may vary from
state to state.
The Warranty is Void in the Following Cases:
Renesas shall have no liability or legal responsibility for any problems caused by misuse, abuse,
misapplication, neglect, improper handling, installation, repair or modifications of the emulator
product without Renesas’ prior written consent or any problems caused by the user system.
All Rights Reserved:
This user's manual and emulator product are copyrighted and all rights are reserved by Renesas.
No part of this user's manual, all or part, may be reproduced or duplicated in any form, in hardcopy or machine-readable form, by any means available without Renesas’ prior written consent.
Other Important Things to Keep in Mind:
1. Circuitry and other examples described herein are meant merely to indicate the characteristics
and performance of Renesas’ semiconductor products. Renesas assumes no responsibility for
any intellectual property claims or other problems that may result from applications based on
the examples described herein.
2. No license is granted by implication or otherwise under any patents or other rights of any third
party or Renesas.
Figures:
Some figures in this user's manual may show items different from your actual system.
Limited Anticipation of Danger:
Renesas cannot anticipate every possible circumstance that might involve a potential hazard.
The warnings in this user's manual and on the emulator product are therefore not all inclusive.
Therefore, you must use the emulator product safely at your own risk.
III
SAFETY PAGE
READ FIRST
• READ this user's manual before using this emulator product.
• KEEP the user's manual handy for future reference.
Do not attempt to use the emulator product until you fully understand its mechanism.
DEFINITION OF SIGNAL WORDS
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
DANGER
WARNING
CAUTION
CAUTION
DANGER indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
CAUTION used without the safety alert symbol indicates a
potentially hazardous situation which, if not avoided, may result
in property damage.
NOTE emphasizes essential information.
IV
WARNING
Observe the precautions listed below. Failure to do so
will result in a FIRE HAZARD and will damage the user
system and the emulator product or will result in
PERSONAL INJURY. The USER PROGRAM will be
LOST.
1. Do not repair or remodel the emulator product by
yourself for electric shock prevention and quality
assurance.
2. Always switch OFF the host computer and user system
before connecting or disconnecting any CABLES or
PARTS.
3. Connect the connectors in the user system and in the
user interface cable by confirming the correct direction.
V
Warnings on Emulator Usage
Be sure to read and understand the warnings below before using this emulator. Note that these are
the main warnings, not the complete list.
WARNING
Always switch OFF the host computer and user system
before connecting or disconnecting any CABLES or PARTS.
Failure to do so will result in a FIRE HAZARD and will
damage the user system and the emulator product or will
result in PERSONAL INJURY. The USER PROGRAM will be
LOST.
CAUTION
Place the host computer and user system so that no
cable is bent or twisted. A bent or twisted cable will impose
stress on the user interface leading to connection or contact
failure.
Make sure that the host computer and the user system
are placed in a secure position so that they do not move
during use nor impose stress on the user interface.
VI
Preface
Thank you for purchasing this user system interface cable (HS36109ECH61H) for the Renesas’
original microcomputer H8/36109 group.
The HS36109ECH61H is a user system interface cable that connects an H8/36109 group E6000
emulator (HS3664EPI61H or HS3664EPI62H; hereinafter referred to as the emulator) to the IC
socket for an FP-100U package for the H8/36109 group MCU on the user system and to the
H8/36109 group expansion I/O board (HS36109EIO61H).
i
Contents
Preface
.........................................................................................................i
Section 1 Configuration.....................................................................................1
Section 2 Connection Procedures ......................................................................3
2.1
2.2
2.3
2.4
2.5
Connecting User System Interface Cable to Expansion I/O Board .................................. 3
Connecting User System Interface Cable to User System ................................................ 5
2.2.1 Installing IC Socket ............................................................................................. 5
2.2.2 Soldering IC Socket............................................................................................. 5
2.2.3 Inserting Cable Head ........................................................................................... 5
2.2.4 Fastening Cable Head .......................................................................................... 6
2.2.5 Fastening Cable Body.......................................................................................... 8
Recommended Dimensions for User System Mount Pad ................................................. 9
Dimensions for User System Interface Cable Head.......................................................... 10
Resulting Dimensions after Connecting User System Interface Cable ............................. 11
Section 3 Installing the MCU to the User System .............................................13
Section 4 Verifying Operation...........................................................................15
Section 5 Notice ................................................................................................17
ii
Section 1 Configuration
CAUTION
Use an NQPACK100SD-ND socket (manufactured by
Tokyo Eletech Corporation) for the FP-100U package IC
socket on the user system.
Figure 1 shows the configuration of the HS36109ECH61H user system interface cable for the
FP-100U package.
To expansion I/O board
CTS screws (M3 x 6 mm)
for fastening the emulator station
Cable body
Screws (M2 x 10 mm)
(for fastening cable head)
Screws (M2 x 6 mm)
Cable head
Socket cover
IC socket
User system
Figure 1 HS36109ECH61H User System Interface Cable
1
Table 1 lists the HS36109ECH61H components. Please make sure you have all of these
components when unpacking.
Table 1
HS36109ECH61H Components
No. Component
Quantity
Remarks
1
Cable body
1
Cable
2
Cable head
1
3
IC socket
1
For the FP-100U package
4
Socket cover
1
For installing an FP-100U-packaged MCU
5
Screws (M2 x 10 mm)
4
For fastening cable head
6
Screws (M2 x 6 mm)
4
For installing an FP-100U-packaged MCU
7
CTS screws (M3 x 6 mm)
2
For fastening the emulator station
8
Guide pins (φ 1 mm)
3
For determining the IC socket location
9
Screwdriver
1
For tightening screws
10
Documentation
1
User’s manual for HS36109ECH61H (this
manual)
2
Section 2 Connection Procedures
2.1
Connecting User System Interface Cable to Expansion I/O Board
WARNING
Observe the precautions listed below. Failure to do so
will result in a FIRE HAZARD and will damage the user
system, the emulator product, and the expansion I/O board
or will result in PERSONAL INJURY. The USER PROGRAM
will be LOST.
1. Always switch OFF the user system and the emulator
product before the USER SYSTEM INTERFACE CABLE
is connected to or removed from any part. Before
connecting, make sure that pin 1 on both sides are
correctly aligned.
2. The user system interface cable dedicated to the
emulator must be used.
To connect the cable body to the emulator station, follow the instructions below.
1. Make sure the user system and emulator station are turned off.
CAUTION
When connecting or removing the user system interface
cable, apply force only in the direction suitable for
connection or removal, while making sure not to bend or
twist the cable or connectors. Otherwise, the connectors
will be damaged.
3
Expansion I/O board
00
TO
ULA
EM
E
6
0
0
E60
0
2. After making sure the direction of the cable body connector is correct, firmly insert the cable
body connector into the expansion I/O board socket (written as USER INTERFACE CABLE),
and fasten the expansion I/O board with two CTS screws (M3 x 6 mm). (figure 2)
US
ER
INT
ER
ABL
EC
FAC
Cable body connector
CTS screws (M3 x 6 mm)
User system interface cable
Figure 2 Connecting User System Interface Cable to Expansion I/O Board
4
2.2
Connecting User System Interface Cable to User System
WARNING
Always switch OFF the user system and the emulator
product before the USER SYSTEM INTERFACE CABLE
is connected to or removed from any part. Before
connecting, make sure that pin 1 on both sides are correctly
aligned. Failure to do so will result in a FIRE HAZARD and
will damage the user system and the emulator product or
will result in PERSONAL INJURY. The USER PROGRAM will
be LOST.
To connect the cable head to the user system, follow the instructions below.
2.2.1
Installing IC Socket
After checking the location of pin 1 on the IC socket, apply epoxy resin adhesive to the bottom of
the IC socket for an FP-100U package, and fasten it to the user system before soldering.
2.2.2
Soldering IC Socket
After fastening, solder the IC socket for an FP-100U package to the user system. Be sure to
completely solder the leads so that the solder slops gently over the leads and forms solder fillets.
(Use slightly more solder than the MCU.)
2.2.3
Inserting Cable Head
CAUTION
Check the location of pin 1 before inserting.
Align pin 1 on the IC socket for an FP-100U package on the user system with pin 1 on the user
system interface cable head, and insert the user system interface cable head into the IC socket on
the user system, as shown in figure 3.
5
2.2.4
Fastening Cable Head
CAUTION
1. Use a Philips-type screwdriver whose head matches
the screw head.
2. The tightening torque must be 0.054 N•m or less.
If the applied torque cannot be accurately measured,
stop tightening when the force required to turn the screw
becomes significantly greater than that needed when first
tightening. If a screw is tightened too much, the screw
head may break or an IC socket contact error may be
caused by a crack in the IC socket solder.
3. If the emulator does not operate correctly, cracks might
have occurred in the solder. Check conduction with
a tester and re-solder the IC socket if necessary.
6
Fasten the user system interface cable head to the IC socket for an FP-100U package on the user
system with the four screws (M2 x 10 mm) provided. Each screw should be tightened a little at a
time, alternating between screws on opposing corners. Take special care, such as manually
securing the IC socket soldered area, to prevent the soldered IC socket from being damaged by
overtightening the screws or twisting the components.
Screws (M2 x 10 mm)
Cable head
Pin 1
User system
IC socket
(NQPACK100SD-ND
manufactured by
Tokyo Eletech Corporation)
Figure 3 Connecting User System Interface Cable to User System
7
2.2.5
Fastening Cable Body
Connect the cable body to the cable head.
Removing
Cable body
Push two remove jigs.
Remove jig
Cable head
User system
Figure 4 Fastening Cable Body
8
2.3
Recommended Dimensions for User System Mount Pad
Figure 5 shows the recommended dimensions for the mount pad (footprint) for the user system
with an IC socket for an FP-100U package (NQPACK100SD-ND: manufactured by Tokyo
Eletech Corporation). Note that the dimensions in figure 5 are somewhat different from those of
the actual chip's mount pad.
17.00 (min.)
13.00 (max.)
17.00 (min.)
13.00 (max.)
0.50 × 24 = 12.00 ± 0.1
0.50 × 24 = 12.00 ± 0.1
0.50 ± 0.05
0.25 ± 0.05
Unit: mm
Figure 5 Recommended Dimensions for Mount Pad
9
2.4
Dimensions for User System Interface Cable Head
76.2
23.0
The dimensions for the user system interface cable head are shown in figure 6.
26.6
23.0
21.5
66.0
Unit: mm
Tolerance: ±0.5 mm
Figure 6 Dimensions for User System Interface Cable Head
10
2.5
Resulting Dimensions after Connecting User System Interface Cable
29.2
The resulting dimensions, after connecting the user system interface cable head to the user system,
are shown in figure 7.
13.3
Cable head
User system
IC socket
(NQPACK100SD-ND
manufactured by
Tokyo Eletech Corporation)
Unit: mm
Tolerance: ±0.5 mm
Figure 7 Resulting Dimensions after Connecting User System Interface Cable
11
12
Section 3 Installing the MCU to the User System
CAUTION
1. Check the location of pin 1 before inserting.
2. Use the screwdriver provided for tightening screws.
3. The tightening torque must be 0.054 N•m or less.
If the applied torque cannot be accurately measured,
stop tightening when the force required to turn the screw
becomes significantly greater than that needed when first
tightening. If a screw is tightened too much, the screw
head may break or an IC socket contact error may be
caused by a crack in the IC socket solder.
4. If the MCU does not operate correctly, cracks might have
occurred in the solder. Check conduction with a tester
and re-solder the IC socket if necessary.
Check the location of pin 1 before inserting the MCU into the IC socket on the user system, as shown
in figure 8. After inserting the MCU, fasten the socket cover with the provided four screws (M2 x 6
mm). Take special care, such as manually securing the IC socket soldered area, to prevent the IC
socket from being damaged by overtightening the screws or twisting the components.
13
Screws (M2 x 6 mm)
Socket cover
MCU
Pin 1
User system
IC socket
(NQPACK100SD-ND
manufactured by
Tokyo Eleteck Corporation)
Figure 8 Installing MCU to User System
14
Section 4 Verifying Operation
1. Turn on the emulator according to the procedures described in the H8/3664 E6000 Emulator
User’s Manual (HS3664EPI61HE-U2 or HS3664EPI62HE-U2).
2. Verify the user system interface cable connections by accessing ports and checking the bus
states of the pins. If an error is detected, recheck the soldered IC socket and the location of pin
1.
3. The emulator connected to this user system interface cable supports two kinds of clock
sources: an emulator internal clock and an external clock on the user system, for the MCU
clock and subclock. For details, refer to the H8/3664 E6000 Emulator User’s Manual
(HS3664EPI61HE-U2 or HS3664EPI62HE-U2).
⎯ To use the emulator internal clock
Select the clock in the emulator station as the system clock (φ) and the subclock (φw), by
using the CLOCK command (emulator command). Note that the on-chip oscillator
function is not supported.
⎯ To use the external clock on the user system as the system clock
Select target clock t with the CLOCK command (emulator command). Supply the external
clock from the user system to the emulator by inputting the external clock from the OSC1
terminal on the cable head or connecting a crystal oscillator to the OSC1 and OSC2
terminals. When a crystal oscillator is inserted into the OSC1 and OSC2 terminals for the
system clock, the clock is generated by the oscillator circuits shown in figure 9. To input
an external clock from the user system, input clock pulses satisfying the specifications
described in the MCU hardware manual into the OSC1 terminal. The system clock (φ)
frequency is the same as the external clock frequency.
⎯ To use the external clock on the user system as the subclock
Select target clock sub t with the CLOCK command (emulator command). Supply the
external clock from the user system to the emulator by inputting the external clock from
the X1 terminal on the cable head or connecting a crystal oscillator to the X1 and X2
terminals. When a crystal oscillator is inserted into the X1 and X2 terminals for the
subclock, the clock is generated by the oscillator circuits shown in figure 9. To input an
external clock from the user system, input clock pulses satisfying the specifications
described in the MCU hardware manual into the X1 terminal. The subclock (φw)
frequency is the same as the external clock frequency.
15
Figure 9 shows the system clock oscillator on the user system interface cable and the subclock
input specifications.
R1 1 MΩ
R7 10 k Ω
R5 3.3 MΩ
HCU04
HCU04
OSC1
To E6000
emulator
R2 270 Ω
OSC2
System clock oscillator
R8 2.2 k Ω
HCU04
X1
R6 470 kΩ
To E6000
emulator
HCU04 HCU04
HCU04
X2
Subclock oscillator
Figure 9 System Clock Oscillator and Subclock Input Specifications
16
Section 5 Notice
1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable
head before inserting the cable head into the user system IC socket.
2. The dimensions of the recommended mount pad for the user system IC socket are different
from those of the MCU.
3. This user system interface cable is specifically designed for the HS3664EPI61H or
HS3664EPI62H emulator. Do not use this cable with any other emulator station.
4. To prevent breaking of wires in the cable body, do not place heavy or sharp metal objects on
the user system interface cable.
5. While the emulator station is connected to the user system with the user system interface cable,
force must not be applied to the cable head. Place the emulator station, user system interface
cable, and user system as shown in the example in figure 10.
Connecting User System Interface Cable to Expansion I/O Board
Emulator station
Place components so that the expansion I/O board, cable body,
and cable head are parallel to the user system.
Expansion I/O board Cable
Cable head is parallel
to emulator station
Cable head is parallel
to user system
User system
Figure 10 User System Interface Cable Location Example
6. The P1 short connector is used for testing. Do not remove the inserted jumper pin.
1
3
P1
Figure 11 P1 Short Connector
17
H8/36109 Group FP-100U
User System Interface Cable
HS36109ECH61H User's Manual
Publication Date: Rev.1.00, April 6, 2006
Published by:
Sales Strategic Planning Div.
Renesas Technology Corp.
Edited by:
Customer Support Department
Global Strategic Communication Div.
Renesas Solutions Corp.
© 2006. Renesas Technology Corp. All rights reserved. Printed in Japan.
Sales Strategic Planning Div.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
RENESAS SALES OFFICES
http://www.renesas.com
Refer to "http://www.renesas.com/en/network" for the latest and detailed information.
Renesas Technology America, Inc.
450 Holger Way, San Jose, CA 95134-1368, U.S.A
Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501
Renesas Technology Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900
Renesas Technology (Shanghai) Co., Ltd.
Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120
Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7898
Renesas Technology Hong Kong Ltd.
7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong
Tel: <852> 2265-6688, Fax: <852> 2730-6071
Renesas Technology Taiwan Co., Ltd.
10th Floor, No.99, Fushing North Road, Taipei, Taiwan
Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999
Renesas Technology Singapore Pte. Ltd.
1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632
Tel: <65> 6213-0200, Fax: <65> 6278-8001
Renesas Technology Korea Co., Ltd.
Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea
Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145
Renesas Technology Malaysia Sdn. Bhd
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: <603> 7955-9390, Fax: <603> 7955-9510
Colophon 6.0
H8/36109 Group FP-100U
User System Interface Cable
HS36109ECH61H
User’s Manual