MTP 1500RL 15HD A SEQ Setup Guide

MTP 1500RL 15HD A SEQ • Setup Guide
This guide provides basic instructions for an experienced installer to set up and operate the
Extron MTP 1500RL 15HD A SEQ twisted pair receiver.
For full details, see the MTP 1500RL 15HD A SEQ User Guide, available online at www.extron.com.
RED
BLUE
DELAY
INPUT
PEAKING
LEVEL
GREEN
ADJUST
RGB
BUFFERED OUTPUT
MIN/MAX
OUTPUT
POWER
12V
1.0A MAX
MONO
L
MTP
MTP 1500RL Series
H+
V+
CSYNC
SOG
VIDEO
END
SPARE
SELECT
AUDIO
R
ON
MTP
MTP 1500RL 15HD A SEQ
Installation and Setup
Step 1 — Mounting
Turn off or disconnect all equipment power sources. Mount the MTP 1500RL 15HD A SEQ receiver as required.
Step 2 — Connect input
Connect the RJ-45 cable from an MTP transmitter to the Input port on the MTP 1500RL 15HD A SEQ receiver.
Terminate the cable as shown below right, using the same standard (A or B) at both ends.
Transmission distance with one device before the MTP 1500RL 15HD A SEQ
RJ-45 Connector
Pin
T568A Wire
Color
T568B Wire
Color
1
White-green
White-orange
2
Green
Orange
3
White-orange
White-green
Transmission distance with more than one device before the MTP 1500RL 15HD A SEQ
4
Blue
Blue
1500 feet (457 m) maximum
5
White-blue
White-blue
6
Orange
Green
7
White-brown
White-brown
8
Brown
Brown
1500 feet (457 m) maximum
Input
Source
Input
Source
NOTE:
VGA
cable
VGA
cable
TP
cable
MTP Tx
Device
MTP Tx
Device
TP
cable
MTP RL Rx
Device
Pins:
12345678
VGA
cable
MTP 1500RL
15HD A Device
TP
cable
MTP 1500RL
15HD A Device
Display
Insert Twisted
Pair Wires
VGA
cable
Display
The transmitter and receiver are designed for and perform best with Extron Enhanced Skew-Free™ AV cable
terminated in accordance with the TIA/EIA T568A standard. CAT 5 cables are acceptable but less preferable.
Using preterminated and tested cables is also recommended. Cables terminated on site should be tested before
use to ensure that they comply with Category 5 specifications.
Step 3 — Connect outputs
Attach the applicable output cables (video, audio, and buffered output).
a.
High resolution video output — Connect a display device to the 15-pin HD connector (RGB).
b. Audio connector — Connect an audio device to the 5-pole captive screw connector for mono audio output
NO GROUND.
Do not tin the wires!
Sleeve(s)
Mono output 2
NO GROUND.
Unbalanced Output
Mono output 1+
Mono output 1Sleeve(s)
Mono output 2+
Mono output 2-
MONO AUDIO
1
2
MONO AUDIO
1
2
Mono output 1
Balanced Output
CAUTION
For unbalanced audio, connect the sleeve(s) to the ground contact.
DO NOT connect the sleeve(s) to the negative (-) contacts.
c.
Buffered output — Connect up to 5 daisy-chained MTP receivers to this RJ-45 connector.
CONTINUED ON SIDE 2
MTP 1500RL 15HD A SEQ • Setup Guide (Continued)
zz
H+
V+
CSYNC
SOG
VIDEO
END
SPARE
Step 4 — Receiver DIP switches
H sync (H+) and V sync (V+) switches — Set these switches up (On) for positive sync
or down (Off) for negative sync.
zz
Composite Sync, SOG, and Video switches — Set these switches as shown
in the table (see right) to output the indicated format.
zz
End Unit switch — Set this switch up if either of the following is true:
a.
ON
Output
Format C Sync SOG Video
RGBHV
RGBS
RGsB
Component*
S-video*
Composite*
* Input video format must match.
The receiver being configured is the only receiver connected to the transmitter.
b. The receiver being configured is the last receiver in a daisy-chained system.
Step 5 — Power
a.
Smooth
Plug the included 12 VDC power supply into the 2-pole
captive screw connector.
Ridges
A
Captive
Screw
Connector
A
b. Wire the connector as shown at right.
Tie Wrap
3"
16 (5 mm) Max.
SECTION A–A
Power Supply
Output Cord
Step 6 — Peaking and Level
Adjust image sharpness with the Peaking control. Increased peaking compensates for mid- and high-frequency detail loss.
The LED lights red when minimum (zero) and maximum peaking is reached.
LEVEL
Adjust image brightness using the Level control. View the image and adjust either control for the best
image quality.
PEAKING
MIN/MAX
RGB
Step 7 — Skew compensation
Pair skew can be measured with test equipment or by viewing a crosshatch test pattern. The SEQ receivers have built-in
skew compensation capabilities. Adjust the equalization as follows:
a.
Set the skew delay to zero for red, green, and blue by pressing and holding the Select
button in for 3 seconds, using a Tweeker or small screwdriver. When the Red, Green, and
Blue LEDs all go out, release the Select button.
RED
SELECT
GREEN
BLUE
DELAY
ADJUST
b. Use UTP cable test equipment or examine the displayed image to determine which video
signal — red, green, or blue — is shifted furthest to the left.
c.
Adjust the furthest left video signal by using a Tweeker or screwdriver to press and release the Select button
until the LED for the left-shifted color lights.
d. Slowly rotate the Adjust control clockwise until the shifted color is properly aligned.
e.
Repeat steps 7c and 7d to align the third color if needed.
Extron
MTP 1500RL 15HD A SEQ
H+
V+
CSYNC
SOG
VIDEO
END
SPARE
Flat Panel
Display
Audio
RGBHV
ON
UT
TP
OU
NO
MOL
IO
AUD
R
Extron
MTP 1500RL 15HD A SEQ
UT
TP
PC
D
RE
OU
FFE
BU
UT
INP
DA
0RL
P 150 ER
MT
P
MT
SEQ
P
MT
Flat Panel
Display
500' (152 m) UTP Cable
(CAT 5/5e/6)
H+
V+
CSYNC
SOG
VIDEO
END
SPARE
RGBHV
15H
POW
12V MAX
0.5A
Audio
Audio
ON
UT
TP
OU
NO
MOL
IO
AUD
R
UT
TP
D
RE
RGBHV
OU
FFE
BU
UT
INP
DA
0RL
P 150 ER
MT
Extron
MTP T 15HD A
15H
P
MT
SEQ
P
MT
POW
12V MAX
0.5A
1,000' (305 m) UTP Cable
(CAT 5/5e/6)
Figure 1. Example of a typical MTP 1500RL 15HD A SEQ application
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West
Extron USA - East
+1.714.491.1500+1.919.863.1794
+1.714.491.1517 FAX
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
Extron Asia
+800.7339.8766
Inside Asia Only
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+4000.EXTRON
+4000.398766
Inside China Only
Extron
Middle East
+971.4.2991800
+971.4.2991880 FAX
+86.21.3760.1568
+86.21.3760.1566 FAX
© 2012 Extron Electronics All rights reserved. www.extron.com
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
Inside India Only
+91-80-3055.3777
+91 80 3055 3737 FAX
68-1554-50 Rev. B
01 12