IDIS TR2204(US) Operation Manual

Digital
Video
Recorder
Operation Manual
TR-2204
Before reading this manual
This operation manual contains basic instructions on installing and using Digital Video Recorder, an IDIS product.
Users who are using this product for the first time, as well as users with experience using comparable products, must
read this operation manual carefully before use and heed to the warnings and precautions contained herein while
using the product. Safety warnings and precautions contained in this operation manual are intended to promote
proper use of the product and thereby prevent accidents and property damage and must be followed at all times.
Once you have read this operation manual, keep it at an easily accessible location for future reference.
•• The manufacturer will not be held responsible for any product damage resulting from the use of unauthorized parts and
accessories or from the user's failure to comply with the instructions contained in this operation manual.
•• It is recommended that first-time users of Digital Video Recorder and individuals who are not familiar with its use seek
technical assistance from their retailer regarding product installation and use.
•• If you need to disassemble the product for functionality expansion or repair purposes, you must contact your retailer and
seek professional assistance.
•• Both retailers and users should be aware that this product has been certified as being electromagnetically compatible for
commercial use. If you have sold or purchased this product unintentionally, please replace with a consumer version.
Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
2
Before reading this manual
Important Safeguards
1. Read Instructions
All the safety and operating instructions should be read before the appliance
is operated.
2. Retain Instructions
The safety and operating instructions should be retained for future reference.
3. Cleaning
Unplug this equipment from the wall outlet before cleaning it. Do not use
liquid aerosol cleaners. Use a damp soft cloth for cleaning.
4. Attachments
Never add any attachments and/or equipment without the approval of the
manufacturer as such additions may result in the risk of fire, electric shock or
other personal injury.
5. Water and/or Moisture
Do not use this equipment near water or in contact with water.
6. Ventilation
Place this equipment only in an upright position. This equipment has an
open-frame Switching Mode Power Supply (SMPS), which can cause a fire or
electric shock if anything is inserted through the ventilation holes on the side
of the equipment.
7. Accessories
Do not place this equipment on an unstable cart, stand or table. The
equipment may fall, causing serious injury to a child or adult, and serious
damage to the equipment. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit approved by the
manufacturer.
This equipment and cart combination should be moved with care. Quick
stops, excessive force, and uneven surfaces may cause the equipment and cart
combination to overturn.
8. Power Sources
This equipment should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power, please
consult your equipment dealer or local power company.
You may want to install a UPS (Uninterruptible Power Supply) system for
safe operation in order to prevent damage caused by an unexpected power
stoppage. Any questions concerning UPS, consult your UPS retailer.
9. Power Cords
Operator or installer must remove power and TNT connections before
handling the equipment.
10. Lightning
For added protection for this equipment during a lightning storm, or when it
is left unattended and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will prevent damage
to the equipment due to lightning and power-line surges.
11. Overloading
Do not overload wall outlets and extension cords as this can result in the risk
of fire or electric shock.
12. Objects and Liquids
Never push objects of any kind through openings of this equipment as they
may touch dangerous voltage points or short out parts that could result in a
fire or electric shock. Never spill liquid of any kind on the equipment.
13. Servicing
Do not attempt to service this equipment yourself. Refer all servicing to
qualified service personnel.
14. Damage requiring Service
Unplug this equipment from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
A. When the power-supply cord or the plug has been damaged.
B. If liquid is spilled, or objects have fallen into the equipment.
C. If the equipment has been exposed to rain or water.
D. If the equipment does not operate normally by following the operating
instructions, adjust only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the equipment to its normal operation.
E. If the equipment has been dropped, or the cabinet damaged.
F. When the equipment exhibits a distinct change in performance ─ this
indicates a need for service.
15. Replacement Parts
When replacement parts are required, be sure the service technician has
used replacement parts specified by the manufacturer or that have the same
characteristics as the original part. Unauthorized substitutions may result in
fire, electric shock or other hazards.
16. Safety Check
Upon completion of any service or repairs to this equipment, ask the service
technician to perform safety checks to determine that the equipment is in
proper operating condition.
17. Field Installation
This installation should be made by a qualified service person and should
conform to all local codes.
18. Correct Batteries
Warning: Risk of explosion if battery is replaced by an incorrect type. Dispose
of used batteries according to the instructions.
19. Tmra
A manufacturer’s maximum recommended ambient temperature (Tmra)
for the equipment must be specified so that the customer and installer may
determine a suitable maximum operating environment for the equipment.
20. Elevated Operating Ambient Temperature
If installed in a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than room ambient.
Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient
temperature (Tmra).
21. Reduced Air Flow
Installation of the equipment in the rack should be such that the amount of
airflow required for safe operation of the equipment is not compromised.
22. Mechanical Loading
Mounting of the equipment in the rack should be such that a hazardous
condition is not caused by uneven mechanical loading.
23. Circuit Overloading
Consideration should be given to connection of the equipment to supply
circuit and the effect that overloading of circuits might have on over current
protection and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.
24. Reliable Earthing (Grounding)
Reliable grounding of rack mounted equipment should be maintained.
Particular attention should be given to supply connections other than direct
connections to the branch circuit (e.g., use of power strips).
3
Before reading this manual
In-Text
Symbol
Type
Description
Caution
Important information concerning a specific function.
Note
Useful information concerning a specific function.
User’s Caution Statement
Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
FCC Compliance Statement
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART
15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE
WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE
RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE
HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO
CAUSE HARMFUL INTERFERENCE, IN WHICH CASE USERS WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT THEIR OWN EXPENSE.
WARNING: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID
THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
THIS CLASS OF DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE CAUSING EQUIPMENT
REGULATIONS.
WEEE (Waste Electrical & Electronic Equipment)
Correct Disposal of This Product
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household
wastes at the end of its working life. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This
product should not be mixed with other commercial wastes for disposal.
4
Before reading this manual
Copyright
© 2016 IDIS Co., Ltd.
IDIS Co., Ltd. reserves all rights concerning this operation manual.
Use or duplication of this operation manual in part or whole without the prior consent of IDIS Co., Ltd. is strictly
prohibited.
Contents of this operation manual are subject to change without prior notice.
Registered Trademarks
IDIS is a registered trademark of IDIS Co., Ltd.
Other company and product names are registered trademarks of their respective owners.
The information in this manual is believed to be accurate as of the date of publication even though explanations of some
functions may not be included. We are not responsible for any problems resulting from the use thereof. The information
contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate
such changes.
The software included in this product contains some Open Sources. You may obtain the complete corresponding source code
from us. See the Open Source Guide on the software CD (OpenSourceGuide\OpenSourceGuide.pdf ) or as a printed document
included along with the Manual.
5
Table of Contents
1
Part 1 - Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Live Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Live Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Video Display Area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Edit Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
PTZ Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Event Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Covert Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Context Menu Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Video Recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Panic Recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Audio Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Video Recording Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
All Channel Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Triplex Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Remote Control Buttons during Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Context Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2
Part 2 - Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Menu Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Text Input via Virtual Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Batch Assignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Mouse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Date/Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
System Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6
Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Pre-Event. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Event Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Motion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Alarm-In. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Video Loss. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Video Blind . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Text-In. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Camera Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
PTZ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Device Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Alarm-Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Network Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
FEN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
RTSP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
IDIS Web. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
VNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
NetFS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Notification Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Callback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Mail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
SNS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
FTP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Display Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
OSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Main Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
7
3
Part 3 - Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Searching Video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Search Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Context Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Event Log Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Record Table Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Motion Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Text-In Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Bookmarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Clip Copy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Print. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Overlapped Recording Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
4
5
8
Part 4 - IDIS Web. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Web Live Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Web Search Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Part 5 - Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Part 1 - Getting Started
3 To log out, bring up the Live menu and click on
Login
(Log out) using the mouse.
Configuring the DVR’s settings and accessing its
searching and other functions require an authorized
user login.
1 Bring up the Live menu and either press the SETUP
button on the remote control or click on
using the mouse.
(Login)
2 Select a user, enter the password, and then select
OK.
•• If you do not know the password, click the
button for guidance.
•• There is no default password for the admin
account. Select admin and then OK without
entering a password to log in.
•• Leaving the admin account unassigned with
a password poses a security risk. Please assign
a password at your earliest convenience. A
warning message will continue to be displayed
until a password is assigned.
•• Click on the
button next to the password
field using the mouse. This will bring up a
virtual keyboard you can use to assign a
password. For more information on using the
virtual keyboard, refer to the Text Input via
Virtual Keyboard on page 20.
9
Part 1 - Getting Started
Live Mode
Placing the mouse pointer near the right edge of the
screen also displays the Live menu.
• Login/Logout
Log into and out from accounts. If in the logged in
state, the account ID is shown. If in the logged out
state, the login icon is shown.
Live Menu
Press the Setup button while in Live mode to bring up
the Live menu on the right edge of the screen. Press
Setup once more to hide the menu. Use the Arrow
buttons on the front panel of the DVR or the remote
control to select the menu options.
• Display
Used to change the screen layout to single screen,
PIP, and 2x2.
–– Camera OSD, Status OSD: Camera OSD or Status
OSD On and Off.
1
2
3
• Previous/Next Group
4
• Freeze
5
6
7
8
9
0
!
@
Loads the previous/next screen group.
Freezes the screen. Select Freeze again to unfreeze.
• Alarm
Pressing this button while the alarm has been
activated resets all DVR outputs, including the builtin buzzer.
• Panic Recording
Activates/deactivates Panic Recording.
• Sequence
1
Login/Logout
2
Display
3
Previous Group
4
Next Group
5
Freeze
6
Alarm
7
Panic Recording
8
Sequence
9
Camera Menu
0
Search
!
Setup
@
Status
10
Initiates Sequence in the same manner as pressing
the SEQUENCE button while in Live mode. To
exit, select Sequence once more or press the
SEQUENCE button on the remote control. The
icon is displayed at the bottom of the screen while
Sequence is in progress.
Part 1 - Getting Started
• Status
Full Sequence
Allows you to check the status of the DVR’s system,
event and storage.
Displays all channels in sequence while in Live mode
(single and PIP split screen settings).
e.g.) Full Sequence in single screen mode
2
1
3
4
1
•• While in the Sequence mode, the sequence icon
displays in bottom-left corner if Sequence is
selected in the Display setup screen.
•• Pages are skipped under the following
circumstances:
Video Display Area
Left-click on the video display area to toggle between
split screen and single screen modes.
Drag the camera screens around to rearrange them.
–– If all cameras included in the page are
deactivated.
–– If there are no video signals.
–– If the page contains "covert" cameras.
–– If the user does not have permission to view
feeds from the cameras.
• Camera Menu
–– PTZ: Allows you to control the selected camera as
long as it has Pan, Tilt and Zoom capabilities. It is
the same as pressing the PTZ button.
–– Zoom: Zooms the current image of the selected
camera on the screen. It is the same as pressing the
ZOOM button. Selecting Zoom again in the Camera
Menu again exits the Zoom mode.
–– Audio: Enable/disable audio.
–– Color Control: Allows you to control brightness,
contrast, hue and saturation for each camera for
the selected camera if a user who has Color Control
authority logs into the system.
Camera Screen
1
–– Menu Control: Adjusts the camera’s self-settings.
Menu Control is supported only for the cameras that
use Pelco-C Protocol and support UTC (Up The Coax)
function.
–– Edit Group: Enter to the Edit Group mode in the
split screen layout.
• Search
–– All Channels: Exits the live monitoring mode and
enters the search mode.
2
1 Camera Title: Indicates the camera’s title.
–– Triplex: Enters the Triplex mode. Selecting the
camera number plays back video of the selected
camera.
• Setup
Used to access the Setup menu.
11
Part 1 - Getting Started
2 Status Indication: Displays system status icons.
Indicates remote control receptivity.
Indicates connection to the DVR from a
remote program.
Camera Menu
Right-click on the video display area to bring up the
camera menu.
Indicates two-way audio connection.
Indicates connection to the DVR using the
VNC service.
Indicates a zoomed in state.
Indicates Freeze is in use.
Indicates Sequence is in use.
1/2
Indicates the current screen's group.
Indicates an event monitoring.
Indicates HDD use. The icon to the left
is shown if using the overwrite setting.
Otherwise, remaining HDD space is shown as
a percentage value.
• PTZ: Allows you to control the selected camera as long
as it has Pan, Tilt and Zoom capabilities. It is the same
as pressing the PTZ button.
• Zoom: Zooms the current image of the selected
camera on the screen. It is the same as pressing the
ZOOM button. Selecting Zoom again in the Camera
Menu again exits the Zoom mode.
• Color Control: Adjusts the camera’s color settings.
• Menu Control: Adjusts the camera’s self-settings.
Menu Control is supported only for the cameras that
use Pelco-C Protocol and support UTC (Up The Coax)
function.
• Edit Group: Enter to the Edit Group mode in the split
screen layout.
• Triplex: The DVR supports the Triplex function:
monitoring, recording and playing back at the same
time.
12
Part 1 - Getting Started
Edit Group
Edit Group lets you customize split screen pages in both
Live and Search modes.
1 While displaying a split screen page, select the Edit
Group option from the context menu. A yellow
border is drawn around the page. Use the arrow
buttons on the front panel or the mouse to select a
different page.
2 Press a Camera button or select a camera after
pressing the Menu button. Selected camera is then
loaded on to the selected page. Repeat to assign
other channels to the page.
Zoom
Press the ZOOM button on the remote control and select
a channel you wish to zoom in on. A zoom frame will
appear on the selected channel. Use the arrow buttons
to position the frame. Press the Play/Pause button
to cycle through various zoom factors. When Zoom is
icon is on the status bar located on the
activated,
bottom of the system.
•• In Full Screen mode, activating Zoom automatically
selects the current channel.
•• To restore the channel to normal size, press the
Zoom button again.
•• The available enlargement ratio is different from
camera mode.
3 Press the remote control’s $ button to exit Edit
Group. Alternatively, press the Menu button and
then select Exit Group Edit to exit.
Edit Group will terminate automatically after 15
seconds of inactivity.
13
Part 1 - Getting Started
PTZ Control
While in Live mode, right-click and select PTZ from the
context menu or press the PTZ button on the DVR’s
front panel or remote control to display the PTZ camera
selection window.
Select the camera you wish to control. The icon will
begin to flash on the selected camera’s OSD window.
Use the Arrow buttons to pan and tilt the camera up,
down, left, and right.
Use the
and
buttons to zoom in/out.
Use the
and
buttons to shift focus from nearby to
far and vice versa. You can also change the direction by
dragging on the mouse.
Also, it’s possible to use the mouse wheel to zoom in/out.
•• Logging in with an account that has PTZ Control
Authority is necessary in order to control PTZ
cameras.
•• A message will prompt if there is no PTZ camera
displayed on the Live screen.
•• Zoom in/out and shift focus using the PTZ Control
(ZOOM, FOCUS) buttons on the remote control.
•• To exit PTZ mode, press the PTZ button again.
14
Setting Up a PTZ Preset
While in PTZ mode, select the PRESET SET button on the
remote control to display the Set Preset window and
assign the current position as a preset.
While in PTZ mode, select the PRESET SELECT button
on the remote control to display the Move to Preset
window. Select a preset to move the current PTZ camera
to the selected preset’s position.
Part 1 - Getting Started
Advanced Settings
In PTZ mode, select a camera. Clicking Menu button and
selecting Advanced PTZ loads the Advanced PTZ screen
as shown below. You can load the Advanced PTZ screen
also by pressing the MENU button and then Play/Pause
button on the front panel. This menu lists Speed, Auto
Pan, and other advanced PTZ camera control options
available for the camera. Options that are not available
for the selected PTZ camera remain inactive.
While in PTZ mode, place the mouse pointer close to
the bottom edge of the screen to display the PTZ Tools
window.
PTZ Camera Pan and Tilt
Zoom In/Out
Focus Near / Far
IRIS Open / Close
Set / Move to Preset
Device Menu supported
by the camera
•• The exact PTZ protocol supported by the camera
must be specified in order to use the DVR's PTZ
controls.
You can use the mouse to control PTZ cameras. Leftclick on the mouse and drag to move the camera in
the desired direction and use the mouse wheel to
zoom in/out.
•• Drag and drop to reposition the PTZ Tools window.
•• Select the
icon to hide the PTZ Tools window.
15
Part 1 - Getting Started
Event Monitoring
When an event occurs, the DVR automatically displays
icon
the channel linked to the event and shows the
on the system status area on the bottom of the screen.
To use the Event Monitoring feature, navigate to Menu >
Display > Main Monitor and enable Event Monitoring.
Event Monitoring remains in effect throughout the entire
Linked Recording Time. After that, the DVR will return
to the previous screen if a new event does not take place.
Pressing the Layout or a Camera button before the end
of the Linked Recording Time reverts the system to Live
mode.
Status
Refer to the Menu Use on page 20 for basic
information on using the Setup menus.
Event Status
This screen displays an overview of all events.
When an event occurs, the corresponding channel
flashes for 5 seconds.
Covert Camera
Use this feature to assign Covert Camera View
permissions.
Navigate to Menu > Camera and designate cameras as
Covert 1 or Covert 2.
• Covert 1: Hides images from the camera in Live mode
but does indicate the camera’s title and status via
icons.
• Covert 2: The camera is indicated as being inactive.
Images from the camera are not shown. Camera title
and status icons are not shown.
Users that have a cover Covert Camera View are
able to view both images from and status icons
for all Covert 1 and Covert 2 cameras.
Alarm-In
Check Alarm-In
Motion
Video Loss
Video Blind
Text-In
• Panic Record: Displays event status based on current
Panic Record status.
• Check Recording: Displays event status based on
System Monitoring settings. For more information,
refer to the System Event on page 30.
16
Part 1 - Getting Started
• Fan Error: Event is indicated when the cooling fan
cannot reach a certain RPM or fails for longer than 50
seconds.
Not
Formatted
• Disk performing
normally.
• No Storage Found: It will be highlighted when no
recordable storage device has been found.
• Disk Almost Full/Disk Full: If the storage device is
not in Recycle status, event status is displayed when
the amount of disk space specified under System
Monitoring is reached and when the disk becomes
100% full. For more information, refer to the System
Event on page 30.
A disk that has never
been used before.
Good
Disk Bad
• Disk Config Change: It will be highlighted when
the DVR reboots after the hard disk drive has been
replaced.
Error
• If the HDD is partially
damaged, indicates
the bad sector
percentage.
• If the HDD's bad sector
ratio is higher than
as designated by the
user.
• Generates a system
event.
Storage
N/A
Unable to detect the
disk's temperature.
Good
Operating within normal
temperature range.
Indicates each disk’s status.
Temperature
Bad
• Disk temperature
higher than as
designated by the
user.
• Generates a system
event.
Configure Disk Bad and Disk Temperature settings under
Setup > System > System Event.
N/A
A disk that does not
support S.M.A.R.T.
Good
A disk with normal
S.M.A.R.T. status.
Bad
A disk with abnormal
S.M.A.R.T. status.
Possibility of damage
within 24 hours.
S.M.A.R.T.
17
Part 1 - Getting Started
Context Menu Access
You can display the ContextMenu window by pressing
the MENU button and then PLAY/PAUSE button on the
front panel. Alternatively, right-click on the mouse to
access the Context menu.
• PTZ: Access PTZ controls.
Video Recording
Video recording will only take place if all the
connections are made correctly as per information
contained in Part 2 of this operation manual.
For more information on video recording settings, refer
to the Record Setup on page 32.
• Zoom: Zoom in.
• Color Control: Select a channel to display its Color
Control window. Adjust the selected camera’s
brightness, contrast, saturation, and hue settings.
• Edit Group: Enter to the Edit Group mode in the split
screen layout.
• PIP: Adjust the PIP screen’s size and location in the PIP
screen layout.
• Triplex: The DVR supports the Triplex function:
monitoring, recording and playing back at the same
time.
Panic Recording
Select Live or Search menu’s Panic Recording
icon or
press the Panic Recording button on the front panel or
the remote control to commence panic recording on all
registered cameras.
To stop Panic Recording, select the Panic Recording
icon or press the Panic Recording button again. If the
Panic Recording Duration option under Record Setup
> General has been configured, Panic Recording will
automatically terminate after the specified duration
of time has elapsed. For more information, refer to the
Record Setup on page 32.
•• Panic Recording takes place irrespective of any
recording schedule set up by the user.
•• Panic Recording ips, Quality, Resolution from
Record Setup – General applies to all Panic
Recording videos.
Panic Recording will not take place if recording mode
is not set to Recycle and the HDD has reached 100%
of its capacity.
18
Part 1 - Getting Started
Audio Recording
Triplex Playback
If the Record Audio option under Record Setup >
General has been enabled the camera will record audio
along with video. For more information, refer to the
Record Setup on page 32.
Check your local laws and regulations on making
audio recordings.
1 Press the Menu button while in Live mode.
2 Select the Search Mode
icon and then select
Triplex.
3 The DVR supports the Triplex function: monitoring,
recording and playing back at the same time.
Video Recording Playback
For more information on data search, refer to the Part 3 Search on page 58.
You can play back video recordings by using mouse or
remote control.
•• Login with an account that has search permission is
needed to playback video recordings.
•• The initial video playback point in Search mode is
the recording's last playback point or the end of the
recording data.
•• Audio playback of the selected recording is available
in full screen mode only.
•• Covert protection on cameras also applies to video
recording playback.
Remote Control Buttons during
Playback
1 Camera Button: Displays the selected recording in
full screen.
2 Zoom Button: Allows you to zoom in on a specific
area of the recording.
All Channel Playback
1 Press the Menu button while in Live mode.
2 Select the Search Mode
icon and then select All
Channels.
3 The selected search mode will be initiated.
3 Layout Button: Cycle between 2x2 and PIP modes.
Context Menu
While in Search mode, right-click on the mouse to access
the Context Menu.
• Zoom: Zoom in.
• Edit Group: Enter to the Edit Group mode in the split
screen layout.
For more information on data search, refer to the Part 3 Search on page 58.
19
Part 2 - Configuration
2 Use the remote control’s arrow buttons to select
Menu Use
Information contained in this section (Menu Use)
applies to all other instructions found throughout Part
3 - Configuration.
Login with an ID that has permission to access the setup
menu is needed to access and make changes to the
Setup menu.
an option and then press the remote control’s $
button or left-click on the option using the mouse.
3 Change the setting and then select Save to save the
change.
To apply default settings, select the Default button
located on the left bottom corner of the setup window.
1 While in Live mode, press the remote control's
MENU button or select Live menu > Setup using the
mouse.
Text Input via Virtual Keyboard
Use the remote control’s arrow buttons to select a
virtual keyboard key and then press the remote control’s
$ button or click on the key using the mouse.
1
2
3
4
5
6
7
8
1
System Setup
2
Record Setup
3
Event Setup
4
Camera Setup
5
Device Setup
6
Network Setup
7
Notification Setup
8
Display Setup
20
Toggle case.
Deletes the character to the left of the cursor.
Deletes the character to the right of the
cursor.
Converts keyboard.
Part 2 - Configuration
Batch Assignment
Certain table-format menus such as the shown in the
Camera Setup on page 41 allow you to change
the title value. In this case, changing the title value
simultaneously changes all other entry values on the
same row.
Mouse
System Setup
Refer to the Menu Use on page 20 for basic
information on using the Setup menus.
General
This Setup menu contains general system options.
Using a mouse makes it easier to configure the settings.
A mouse lets you make selections faster and use its
wheel to scroll through long menus. You can also use
the mouse wheel to increase/decrease numerical values.
• Site: Used to enter a description about the system’s
installation site (no description by default). You can
edit the information using the virtual keyboard.
• System ID: Used to identify the DVR apart from other
DVRs. System ID is also used to control the DVR with
the remote control and identify the unit when it is
connected with other DVRs through the RS485 port.
The default System ID is 0 and can be changed to a
value between 0 and 99. The System ID can also be
entered using the virtual keyboard.
• Language: Choose a language.
• Version: Indicates the software version.
21
Part 2 - Configuration
• Upgrade: Upgrade the system. If NetFS feature is
in use, click Upgrade. You can select the USB Port or
NetFS. If NetFS feature is not in use, you can select
the USB port only. Selecting the USB port displays the
USB search window. You will then be able to select an
upgrade package and upgrade the system. Selecting
the NetFS displays the registered FTP site lists.
Once the upgrade is complete, the DVR will reboot
automatically.
• Show System Log: Displays a searchable list of 5,000
most recent system log entries. For more information
on types of system log entries, refer to the System
icon
Log Types in the installation manual. The
appears next to log entries originating from a remote
source. To export the system log, select the Export
at the bottom of the screen and then designate a file
name.
•• The “.rui” indicates that the file is for software
upgrades.
•• If an upgrade attempt fails, an upgrade failure
message will be displayed. Refer to Error Code
Types in the installation manual for more details.
• Setup: Exports current DVR settings or imports
existing settings. If NetFS feature is in use, you can
export or import DVR settings in the registered FTP
site.
–– Import: Decide whether to import network settings
as well. If you do not wish to change the current
network settings, do not select Include Network
Setup.
Selecting Setup Import does not change the
settings below.
• To export the system log information, connect the USB
device to the DVR. If you enabled the NetFS function
(Network menu > NetFS tab), you can upload the log
information on the registered NetFS site. Click Export.
Select USB Storage or NetFS. If you select NetFS,
select a NetFS site from the registered NetFS site list.
A virtual keyboard allows you to enter the file name.
Selecting Export will save the log information in .txt
file format on the USB device or the NetFS site.
•• Time-related settings (Date/Time, Time Zone, and
Use Daylight Saving Time)
–– Export: Exports the current system settings to
a storage device connected to the system’s USB
port or the registered FTP site in NetFS. You can
designate a File Name for the export file.
For USB flash memory devices, the DVR supports
the FAT16 and FAT32 files format.
22
In order to display the system_log.txt file, you must
use the correct character encoding settings and use
a fixed-width font.
Part 2 - Configuration
• Clear All Data: Erases all recording data. Selecting
Clear All Data displays a confirmation window. Select
Clear to proceed.
•• Before you perform Clear All Data, make sure you
are not accidentally deleting important data. Erased
data cannot be recovered.
Quick Wizard
1 Select Quick Wizard.
•• Clear All Data does not affect the system log.
Instead, the Clear All Data event will be added to
the log.
• Wizard: Lets you configure basic settings required for
operating the system.
1 Select the desired Setup Wizard option and click
Next.
2 Specify the current date and time and then click
Next.
Select Cancel from any of the Wizard screen to cancel
the setup process and return to the main setup menu.
•• The new date and time settings will only be
applied after clicking Next.
•• For more information on date and time
settings, refer to the Date/Time section under
System Setup on page 21.
23
Part 2 - Configuration
3 Choose the desired Recording Method and click
Next.
–– Recording ips, quality, resolutions used under each
recording method and record video quality setting are as
follows:
High Video
Quality Priority
Profile
Standard
Longer Recording
Recording Profile Time Priority
Profile
Very high, Very
high, 30 ips
High, Very High,
15 ips
Standard, High,
5 ips
Continuous Very high, Very
& Motion
high, 30 ips
Event
(Time/Event)
Record
Time: High, Very
High, 15 ips
Event: Very High,
Very High, 30 ips
Time: Standard,
High, 5 ips
Event: High, Very
High, 15 ips
Very high, Very
high, 30 ips
High, Very High,
15 ips
Standard, High,
5 ips
Motion
Event
Record
Continuous
4 Choose the desired Recording Quality and click
Next.
Higher recording quality uses up more disk space.
24
5 Click Finish to exit Quick Wizard.
Part 2 - Configuration
Network Wizard
After exiting from Quick Wizard, you can click Go to
Network Setup and set up the network with Network
Wizard.
3 Select Network Configuration and then click
Next. Select either Auto Configuration or Manual
Configuration and then click Test to test the system’s
current network configuration.
1 Select Network Wizard.
•• This test must be performed before proceeding
to the next step.
2 Specify whether the system is connected to the
Internet and click Next.
•• If the DVR is on a network connected to a
network that has a DHCP server, selecting Auto
Configuration retrieves LAN settings such as
IP and DNS addresses automatically. Selecting
Manual Configuration, on the other hand, lets
you specify the settings manually.
•• UPnP support device not found. If this error
message is displayed, check to see if the IP
router (or NAT) supports UPnP and if UPnP has
been enabled. For more information about the
router's UPnP function, refer to the router's
operation manual.
If you have chosen No, wait for the test to finish
and then click Finish to exit Network Wizard.
25
Part 2 - Configuration
4 Enter in the FEN Name field the DVR name to be
registered on the FEN server and then click Check to
check its availability.
5 Click Finish to exit Network Wizard.
• System Shutdown: Shuts down the system. When
prompted, select System Shutdown.
•• The FEN name you register on the FEN server
will be a unique name used to identify the
DVR. Once registered, the name can be used
to access the DVR directly from clients such as
the IDIS Center. Check the name's availability
to complete the registration process. The Finish
button will then become activated.
•• You will be prompted with an error message if
you do not enter a name for the DVR or enter a
name already registered on the FEN server.
•• Depending on the network environment,
FEN services may not be active and therefore
prevent the DVR from connecting to the
network. In this case, you will need to manually
configure the ports. For more information on
port configuration, refer to Network Setup on
page 45.
26
Part 2 - Configuration
Date/Time
3 Specify the server synchronization Interval.
4 Select OK to apply and exit.
•• If you have configured the DNS Server setting under
Network - IP Address, you can enter the time
server's domain name instead of its IP address.
•• Selecting Run as Server sets the current DVR as a
time server for other DVRs within the system.
• Holiday: Designate holidays. On specified holidays,
recording takes place according to the holiday
recording schedule specified under Record Schedule.
1 Select the + button at the bottom of the window.
• Date: Used to change the system’s date setting.
• Time: Used to change the system’s time setting.
• Date Format/Time Format: Used to change the
system’s date and time formats.
• Time Zone: Used to designate the system’s time zone.
2 Select a date.
3 Select OK to apply and exit.
Refer to the map displayed on the screen and change
the time zone using the mouse or the arrow buttons.
• Use Daylight Saving Time: Enables DST correction.
• Time Sync.: Select a time server for the system to
synchronize with.
1 Select Automatic Sync.
Select the
icon to delete the existing holiday date.
2 Enter the Time Server’s IP address or domain name
or select and then choose a server from the list of
registered time servers.
27
Part 2 - Configuration
User
3 Select + User and then enter a user name.
Use this option to register users and assign permissions.
4 Select a group for the user and then enter a
password. The password can be 8~16 characters in
length and may include numbers.
5 Select OK.
6 Configure Auto Login and Auto Logout settings.
1 Select + Group and enter a group name. A group
name can be up to 15 characters in length.
2 Specify the group’s permission settings. For more
information on permission settings, refer to the
Group Permissions on page 29.
7 Select Save to exit.
•• Group names, user names, and passwords can
be entered using the virtual keyboard. For more
information on using the virtual keyboard, refer to
the Text Input via Virtual Keyboard on page 20
•• To delete a registered user or group, select the
icon on the right of the corresponding user/group.
Group Administrator and User admin cannot be
deleted.
•• Select the
icon next to Group & User on the
top of the screen to delete all groups and users
except Group Administrator and User admin
simultaneously.
•• A password entry is required to edit existing groups
and users.
•• Group Administrator's permissions cannot be
changed.
•• With the User admin account, only the password can
be changed.
•• When the system starts up, it will automatically log
into the account designated under Auto Login.
•• The system will automatically log out of the account
if the duration of inactivity specified under Auto
Logout.
28
Part 2 - Configuration
Group Permissions
System
Shutdown
May shutdown the system from
the system menu.
Upgrade
May upgrade the system from
the system menu (System Setup).
Color Control
May adjust each camera's
brightness, contrast, saturation,
and hue settings.
System Check
May view System Check results.
PTZ Control
May control PTZ cameras.
Alarm-Out
Control
May reset in the event of an
alarm-out.
Alarm-outs can be reset by
pressing the Alarm button
on the device or selecting the
Alarm-Out Control button on
the remote program.
Covert Camera
View
May access covert cameras in
Live and Search modes.
Clip
Copy
The user who has permission
for Clip Copy can perform
Clip Copy. If the user does not
have permission, Clip Copy is
not allowed but only search is
allowed.
Search
System May change the system's date
Time
and time settings.
Change
Setup
Data
Clear
May clear data stored in the
system.
PTZ
Setup
May configure PTZ settings.
AlarmOut
Setup
May configure alarm-out
settings.
Covert May configure convert camera
Camera settings.
Setup
Record
Setup
May configure recording settings.
Setup
Import
May import previously saved
DVR settings.
Setup
Export
May export current DVR settings.
VNC
Setup
May access the DVR and control
it remotely via network.
29
Part 2 - Configuration
Storage
System Event
Use this option to configure storage settings.
Use this option to configure Monitoring settings.
• Type: Indicates the type of the installed disk.
• Settings: Configure when and what the system
should monitor for.
• Capacity: Indicates the disk’s capacity.
• Format: If the disk has been formatted, indicates
either Record or Not Using. If you have connected an
unformatted storage device, the Use As value will be
indicated as Not Formatted.
• Information: Indicates if the disk is being used for
recording purposes. Disks that were used in different
systems will show up as Other. Select Information
to check the saved data’s time information or select
Delete to erase the data.
•• Select Format to prepare the disk as a storage for
data recording.
•• Disks formatted with Use As set to Not Using will
not be used for data recording.
•• This DVR supports SATA2 HDDs.
30
• Actions: Configure alarm-out (DVR alarm-out channel,
DVR beep) and notification (email, LAN1 through 5,
SNS, push, alert window) settings.
Part 2 - Configuration
Monitoring Options
System
Define monitoring times. If selfdiagnosis is not performed on
a regular basis, the system will
assume an error.
Bootup, Restart,
Shutdown
Define bootup, restart and
shutdown actions.
Panic Record
Define panic recording actions.
The system will assume an error
if the system has been scheduled
to record normally but recording
does not take place during
scheduled intervals.
Check Recording
Select Schedule On and then
configure the days of the week,
times, and monitoring interval.
Select the button on the
bottom left of the screen to
add a schedule. Select
icon
to delete the schedule.
Disk Full
Generates an event when all
disks reach their maximum
capacity.
Disk Bad
Generates an event when the
specified percentage of the
disk becomes damaged. Set to
between 10% and 90% in 10%
intervals.
Disk
Temperature
Specify the threshold
temperature. Once any disk
reaches this threshold, the
system will issue an alert.
Disk S.M.A.R.T.
Monitors disks that support
S.M.A.R.T. and notifies the user if
a disk error is detected.
Disk Config
Change
It will be highlighted when the
DVR reboots after the hard disk
drive has been replaced.
Fan Error
Notifies the user when the fan
inside the system malfunctions.
No Storage
Found
It will be highlighted when
no hard disk drive has been
connected.
•• For system events, only an e-mail notification of
actions can be selected.
•• In order to use the Notify(Callback) feature, the DVR
must be registered to the remote program on the
receiving PC's end.
Check Alarm-In
The system will assume an error
if the alarm-in status does not
change during the specified
monitoring interval while alarmin is active.
Disk Almost Full
Generates an event if the disk
reaches the specified capacity
(80% to 99%).
31
Part 2 - Configuration
Record Setup
Refer to the Menu Use on page 20 for basic
information on using the Setup menus.
General
Configure general recording settings.
• Auto Deletion: Configure this option to delete
recording data automatically after the specified
number of days has elapsed. Select between 1 day
and 999 days.
To disable Auto Deletion, select Never. If enabled,
recording data will be stored on the DVR for
the specified number of days and then deleted
automatically. Expired recording data are deleted
automatically at midnight and will be deleted even if
the system reboots or the Auto Deletion setting has
been changed.
• Limit Time-Lapse Recording: You can store event
recording data for longer. If you do not wish to use
Limit Time-Lapse Recording, select Never. This
function is activated when data has been stored for
longer than as configured because the recording
disk has sufficient capacity and saves new data by
overwriting Time Lapse Recording data that are
older than as specified under Recycle mode.
• Recycle: When the recording disks become full,
the system overwrites existing data with new data,
starting with the oldest first. If Recycle is disabled,
recording will simply stop when the recording disks
reach their maximum capacity.
• Event Record Dwell: If linked recording is designated
as an event-triggered action, recording takes place for
the duration specified under this setting.
• Record Audio: The camera will record audio along
with video.
32
•• If the recording stored on the disk is shorter than
the duration specified under Limit Time-Lapse
Recording, the older of Event Recording or Time
Recording data is deleted first.
•• The system's recording time may change depending
on recording quality, resolution, motion, and other
configurations made by the user. The duration
specified under Limit Time-Lapse Recording may
not be guaranteed in certain situations.
Part 2 - Configuration
• Use Panic Recording: Enable/disable Panic
Recording.
Schedule
• Panic Recording Duration: Disable Panic Recording
automatically. Select between 5 mins and 1 hr. If you
do not wish to disable the feature automatically,
select No Limit.
• ips: Allow you to set the images per second for Panic
recording.
• Quality: Allow you to set the recorded image quality
for Panic recording. You can select from: Very High,
High, Standard and Basic.
• Resolution: Allow you to set the recorded image
resolution for Panic recording. You can select from:
Very High, High, and Standard.
<Simple Mode>
<Advanced Mode>
Disabling Schedule On suspends schedule recording
regardless of the schedule and displays the
icon on
the upper left corner of each camera screen. Pressing
icon and
the Panic Record button displays the
commences panic recording.
Set Record Schedule mode as Simple Mode or
Advanced Mode. Advanced Mode allows you to
configure a unique recording schedule for each event.
Select the icon to delete a schedule.
•• Changing the recording schedule mode suspends
all active event-linked actions.
•• Select the + button on the bottom left of the screen
to add a schedule. Select Day to specify the Day
setting or select All. Select Scope to specify the
time frame.
33
Part 2 - Configuration
Simple Mode Options
Advanced Mode Options
• Mode: Select No Record, Time, Event, or Time &
Event.
Select to configure event types.
• Type: Event-specific and time recording icons are as
follows:
No
Record
Time
Unless the Panic Record button is
pressed, no recording will take place
during the scheduled time frames on the
scheduled days.
icon appears on the upper
The
icon
left corner of the screen. The
appears at scheduled times to indicate
recording is in progress.
icon appears on the upper
The
icon
left corner of the screen. The
appears when the specified event occurs
to indicate recording is in progress.
Event
Time &
Event
If Pre-Event is enabled, the
and
icons appear when recording is
not in progress, or the
and
icons appear when an event occurs
and recording is in progress.
icon appears on the upper left
The
corner of the screen and recording
commences as per the ips, Quality,
Resolution selected for time under
Setup. When an event occurs, the icon
icon and recording
changes into
commences as per the ips, Quality,
Resolution selected for events under
Setup.
• Channel: Select which cameras to apply the schedule
to.
• Settings: Select to configure default values for Time
Lapse and Event Recording modes.
34
Time Lapse
(Time)
Video Loss
Alarm-In
Video Blind
Motion
Detection
Text-In
• ips: Allow you to set the images per second for Time
and Event recording.
• Quality: Allow you to set the recorded image quality
for Time and Event recording. You can select from:
Very High, High, Standard and Basic.
• Resolution: Allow you to set the recorded image
resolution for Time and Event recording. You can
select from: Very High, High, and Standard.
• Dwell: Specify how long to record for after a
corresponding event occurs.
Part 2 - Configuration
•• Upper-tier schedule's settings apply to
unconfigured channels.
•• If multiple events take place on a specific channel
and different ips, Quality, Resolution, and Dwell
Time settings apply, highest settings apply to all
event-linked recordings.
Pre-Event
When an event occurs, enabling this option includes
the specified duration prior to the event in the eventtriggered recording.
•• The resolution can be set up at a time for each
event or separately for each channel of an event.
When setting up at a time for each event, the
following options are available: Very High, High
and Standard. Selecting Very High, the highest
resolution will be applied. Selecting Standard,
the lowest resolution, and selecting High, the
other resolution will be applied. When setting up
separately for each channel of an event, you can
select any resolution supported by the camera
mode (720, 960, HD or Full HD).
• No.: Select which cameras to apply Pre-Event to.
Event
720 Mode
• ips, Quality, Resolution: The image quality can be
selectable from Very High, High, Standard and Basic,
and image resolution can be selectable from Very
High, High, and Standard.
• Dwell: Specify the duration of pre-event recording
data.
•• If no event mode schedule exists in the schedule, a
warning message prompting you to add an event
mode schedule will be displayed.
960 Mode
HD Mode
•• The warning message will appear even in Time &
Event mode.
Full HD Mode
35
Part 2 - Configuration
Event Setup
• Sensitivity: Set daytime and nighttime sensitivity
settings between 1 (Low) and 5 (High).
Refer to the Menu Use on page 20 for basic
information on using the Setup menus.
Motion
• No.: Select which cameras to apply Motion Detection
to.
36
• Zone: Define the motion detection block.
Part 2 - Configuration
Use the remote control’s arrow buttons to move the
block selection window up, down, left, and right. The
selection window consists of 4 blocks per row. Select/
deselect individual blocks using the Camera buttons.
You can use the mouse to drag the zone and then select,
clear, or reverse the selection.
From the zone selection screen, press the $ button on
the remote control or right-click on the mouse to open
up the Zone Setup menu.
• Min. Blocks: Motion needs to be detected in more
than the specified number of blocks in order to
trigger a Motion Detection event. You may select a
value between 1 and the number of blocks selected
under Zone for daytime and nighttime, each.
• Motion Ignoring Time: The system does not produce
event log entries or issues remote notifications
regarding motion detected during the specified time
following the initial motion detection. Set a value
between 1 sec and 10 secs or choose Never.
Motion Ignoring Time does not affect motion
detection recording.
–– Select: Confirm the block selection in the selection
window.
–– Clear: Clear the block selection in the selection
window.
–– Reverse: Clear the blocks selected within the
selection window and select all unselected blocks
within the selection window.
–– Select All: Select all blocks.
–– Clear All: Clear all block selections.
–– Reverse All: Clear all selected blocks within the
screen and select all unselected blocks within the
screen.
–– OK: Save the changes and exit the menu.
–– Cancel: Exit the menu without saving the changes.
• Actions: Specify which actions to take when motion
is detected.
–– Record: Specify which cameras to begin linked
recording on when an event occurs. If the schedule
is set to Event or Time & Event mode, the selected
cameras will begin linked recording when an event
occurs.
–– Alarm-Out: Designate event-triggered alarm-out
channels and beeps.
–– Notify: Configure to be notified of events by
Mail, LAN1 through 5, SNS, FTP, Push, and/or Alert
Window.
–– PTZ: Moves the PTZ camera to a specific preset
position when an event occurs.
In order to use the Callback feature, the DVR must be
registered on the remote program.
• Daytime Setup: Specify when daytime starts and
ends. Adjust the time frame in 15-minute increments.
Times outside the specified range will be assumed as
nighttime by the system.
37
Part 2 - Configuration
Alarm-In
• No.: Enable / disable alarm-ins.
• Title: Use the virtual keyboard to enter titles.
• Type: Change the alarm-in type.
• Actions: Specify which actions to take when Alarm-In
is detected.
–– Record: Specify which cameras to begin linked
recording on when an event occurs. If the schedule
is set to Event or Time & Event mode, the selected
cameras will begin linked recording when an event
occurs.
–– Alarm-Out: Designate event-triggered alarm-out
channels and beeps.
–– Notify: Configure to be notified of events by
Mail, LAN1 through 5, SNS, FTP, Push, and/or Alert
Window.
–– PTZ: Moves the PTZ camera to a specific preset
position when an event occurs.
In order to use the Callback feature, the DVR must be
registered on the remote program.
Video Loss
• Video Loss Interval: The system does not produce
event log entries or issues remote notifications
regarding video loss detected during the specified
time following the initial video loss detection. Set a
value between 0.1 sec and 15 secs or choose Never.
• Actions: Specify which actions to take when a Video
Loss event occurs.
–– Record: Specify which cameras to begin linked
recording on when an event occurs. If the schedule
is set to Event or Time & Event mode, the selected
cameras will begin linked recording when an event
occurs.
–– Alarm-Out: Designate event-triggered alarm-out
channels and beeps.
–– Notify: Configure to be notified of events by
Mail, LAN1 through 5, SNS, FTP, Push, and/or Alert
Window.
–– PTZ: Moves the PTZ camera to a specific preset
position when an event occurs.
In order to use the Callback feature, the DVR must be
registered on the remote program.
• Use Ignoring Time: Select Time Setup to specify the
video loss detection ignore time. Video loss detection
will be disabled during the specified time frame.
38
Part 2 - Configuration
Video Blind
• Actions: Specify which actions to take when video
blind events occur.
–– Record: Specify which cameras to begin linked
recording on when an event occurs. If the schedule
is set to Event or Time & Event mode, the selected
cameras will begin linked recording when an event
occurs.
–– Alarm-Out: Designate event-triggered alarm-out
channels and beeps.
–– Notify: Configure to be notified of events by
Mail, LAN1 through 5, SNS, FTP, Push, and/or Alert
Window.
–– PTZ: Moves the PTZ camera to a specific preset
position when an event occurs.
• Sensitivity: Allow you to adjust the DVR’s sensitivity
to video blind for Black and White independently from
0 (Never) and 1 (least sensitive) to 15 (most sensitive).
Video blind might NOT be detected for a camera
with a very noisy image especially when set for low
sensitivity values.
In order to use the Callback feature, the DVR must be
registered on the remote program.
• Use Ignoring Time: Select Time Setup to specify
the video blind detection ignore time. Video blind
detection will be disabled during the specified time
frame.
• Activation Time: Allow you to set the duration before
the DVR will report a Video Blind. The DVR will not
consider any blinded camera to be a Video Blind if the
detected blindness is less than the Activation Time set
on this screen.
39
Part 2 - Configuration
Text-In
• Transaction Start: Once Transaction Start has been
designated, the system will recognize the specified
string as the beginning of a transaction. You can
choose the Any Character setting. Under this setting,
any character will trigger the system into recognizing
the start of a new transaction.
• Transaction End: Once Transaction End has been
designated, the system will recognize the specified
string as the end of a transaction. Select 0 more
line(s) next to Transaction End and specify a value
between 1 and 10. The system will recognize the
specified Transaction End string plus the number of
lines as being the end of a transaction.
• Setup: Configure text-in devices.
• Line Delimiter: Designate a string to mark the end of
a line. You can enter control strings by selecting
and then entering ^, followed by a letter. For example,
Carriage Return is ^M and Line Feed (new line) is ^J.
• Ignore String: Specify a string to ignore from
transaction records.
• Case Sensitive: Ignores case in strings designated
under Transaction Start, Transaction End, Line
Delimiter, and Ignore String.
Case Sensitive does not apply to control strings.
•• It's possible to batch configure all text-in devices
with the exception for port settings.
•• An influx of large amounts of text-in data
from multiple channels can hinder system
performance.
• Text-In Product: The setup window is updated so
that the portion below the port setting matches the
corresponding text-in device. Displayed screenshot
illustrates Generic Text settings.
40
• Time Out: Once Time Out has been enabled, the
system will assume the end of a transaction if no new
string is entered within the specified duration of time.
Select between 5 secs and 15 mins.
Part 2 - Configuration
Selecting RS-232, RS-485, USB-Serial 1 through 8, or LAN
1 through 4 as the port activates the Port Setup button.
Select Setup and configure the Baud Rate, Data Bit,
Stop Bit, and Parity settings.
•• If any one of LAN1 through 4 has been selected as
the port, select the Port Setup button and configure
the network port setting.
•• If using a USB-serial port, the Text-In feature may
malfunction if the USB cable is removed while the
system is in operation.
• Title: Designate a name for the text-in device.
Camera Setup
Refer to the Menu Use on page 20 for basic
information on using the Setup menus.
General
Enable/disable the covert view and rename cameras.
• Actions: Specify which actions to take when text-in is
detected.
–– Record: Specify which cameras to begin linked
recording on when an event occurs. If the schedule
is set to Event or Time & Event mode, the selected
cameras will begin linked recording when an event
occurs.
–– Alarm-Out: Designate event-triggered alarm-out
channels and beeps.
–– Notify: Configure to be notified of events by
Mail, LAN1 through 5, SNS, FTP, Push, and/or Alert
Window.
–– PTZ: Moves the PTZ camera to a specific preset
position when an event occurs.
• No.: Turn the camera number On or Off.
• Title: Edit the camera’s name.
In order to use the Callback feature, the DVR must be
registered on the remote program.
41
Part 2 - Configuration
• Use: Set the camera as Normal, Covert 1, or Covert 2.
Live images and video recordings from cameras that
have been set as Covert 1 or Covert 2 will not be
available to users who do not have covert camera
access. Setting a camera as Covert 1 hides its images
but does display OSD information about the camera.
Setting a camera as Covert 2 hides its images as well
as OSD information about the camera as if it has been
deactivated completely.
PTZ
You will only be able to set up PTZ devices if the PTZ
port is set to RS232 or RS485.
• Type: Select the type supported by the camera
among Auto, SD, HD-TVI and HD-A. Selecting Auto
allows the DVR to automatically detect the type
supported by the camera.
• Mode: Select the width resolution supported by
the camera among Auto, 720, 960, HD and Full HD.
Selecting Auto allows the DVR to automatically detect
the width resolution supported by the camera.
•• When selecting Auto, the 720, HD and Full HD
mode are supported. The input resolution is
applied without rebooting the system. If the
camera’s width resolution is 960 and Mode is set
to Auto, 720 mode will be applied.
•• When you change mode, the system restarts
automatically.
• Product: You can select the PTZ camera you wish to
configure.
• ID: You can assign IDs to each camera by highlighting
the box under the ID heading. Change the number
by highlighting it and using the Up and Down arrow
buttons to increase and decrease the number. The
PTZ ID number can be set from 0 to 256.
<RS232/RS485>
<UTC>
• Mode: Select None, UTC, RS232, or RS485. UTC is
only used for HD and Full HD cameras.
42
Part 2 - Configuration
• You will need to connect the camera to the RS232 or
RS485 connector on the back of the DVR following the
camera manufacturer’s instructions.
Device Setup
Refer to the Menu Use on page 20 for basic
information on using the Setup menus.
Audio
Configure the port’s setting based on the PTZ camera
manufacturer’s instructions.
The DVR can record up to four audio inputs. A list of
cameras appears, and you can select which camera you
want associated with that audio input.
43
Part 2 - Configuration
Alarm-Out
Select the + icon at the bottom left corner of the screen
to add a schedule.
You can apply different schedules for different Days of
the week.
Select icon to delete the schedule.
• Dwell Time: Select a value between 5 secs and 15
mins as the alarm-out duration.
• Title: Designate a name for the alarm-out.
• Range: Change the schedule time frame.
• Mode: Select Event, On, or Off.
Event
Generates an alarm-out when an event
occurs.
On
Alarm-out is always on.
Off
Alarm-out is always off.
• Channels: Configure alarm-out port and beep
settings.
44
Remote Control
• Port: Select None, RS232 or RS485 and then click
the Setup button and then select the correct Baud
Rate, Parity, Data Bits and Stop Bits for the device
you are connecting to the DVR. You can select the
device from the Remote Control Product list. If the
RS232 port and RS485 port are in use for PTZ control,
networking or text input, the remote keyboard cannot
be configured. In this case, the warning message
window will appear when other devices use the same
port such as PTZ control, networking or text input.
The message says that you cannot use other device
because the ports are overlapped.
Part 2 - Configuration
Network Setup
Refer to the Menu Use on page 20 for basic
information on using the Setup menus.
• Remote Audio Channel: Transmits the selected
channel’s audio to the remote program. Select Select
From Client to stream audio of the channel selected
on the remote program.
Audio skipping and sync issues can occur under poor
network conditions.
General
• Enable SSL for Transferring Data: Applies SSL
(Secure Sockets Layer) protection on remote viewing
and recording data transmissions.
•• If using the SSL feature, it will not be possible to
connect to the DVR from a remote program or a
network keyboard that does not support SSL.
•• Changing the SSL setting temporarily severs all
remote connections to the DVR in order to apply the
change.
•• This product contains content developed by
OpenSSL Project for use in Open SSL Toolkit (http://
www.openssl.org/).
• Multi Stream: Supports more than one stream.
Configure to use different streams in layout mode or
channels in IDIS Center Client.
During playing, the transfer speed can be low.
• bps/ips: Select the Transfer Speed from 50Kbps to
1Gbps and the unit of measure for the transfer speed
between: bps and ips. The available value differs
depending on the quality and resolution settings.
• Quality: Select the Quality from: Very High, High,
Standard and Basic.
• Resolution: Select the Resolution from: Very High,
High and Standard.
The higher Quality and Resolution settings require
higher Transfer Speed settings. The transfer speed you
set is the maximum speed. Depending on the network
environment, this speed may not be achieved.
• Network Bandwidth Limit: Configure the bandwidth
to limit.
If you configured the Network Bandwidth Limit, the
live video may not be displayed smoothly in a remote
program.
45
Part 2 - Configuration
LAN
Designate the IP address type as Manual or DHCP.
• Status: Indicates the number of the port forwarded
by the IP router (or NAT) to the DVR via UPnP service.
• Test: Select to test the current LAN settings you made.
Manual
1 Enter the address of the DVR to test.
• Set Type to Manual.
Manual lets you configure related settings manually.
Configure IP Address, Gateway, and Subnet Mask
settings manually using the remote control's arrow
buttons or the mouse wheel.
2 Adjust the frequency of the ping test.
3 Select Run to do the test. The test result is displayed.
4 Select Close to exit.
• DNS Server: Enter the DNS server’s IP address. The IP
address can also be entered using the mouse wheel.
•• If using a firewall, select Change Port to change the
port number to one that is permitted by the firewall.
• Port Number Setup: Change the numbers by
highlighting them and using the Up and Down
arrow buttons to increase or decrease the number.
The factory default Port settings are: 8200(Remote
Admin), 8201(Remote Callback), 8016(Remote Watch),
and 10019(Remote Search).
•• Changing the port temporarily severs the DVR's
remote connection.
You will need to get the appropriate Port Numbers
for each IDIS Center and IDIS Web related program
(Admin, Callback, Watch and Search) from your
network administrator.
To use the UPnP (Universal Plug and Play) feature, select
Use UPnP. If using an IP router (or NAT), UPnP service
allows the device to automatically forward the port to
the DVR.
•• This port is used to access a port that has a private
IP address.
•• In order to use the UPnP service, the IP router (or
NAT) must support UPnP port forwarding and have
the relevant options enabled.
•• Port number cannot be changed with Use UPnP
selected.
46
Remote point IP and port settings on the remote
program must also be changed in order for it to
connect to the DVR.
Part 2 - Configuration
DHCP
FEN
If using a dynamic IP address, FEN service makes it easy
to connect to the DVR from a remote program without
having to configure dynamic IP or router settings.
Select DHCP and then Save to retrieve IP address and
other network settings automatically from the DHCP
server. Once the network settings have been retrieved,
the DVR’s current IP address is displayed in the IP
Address field.
•• It may not be possible to retrieve the IP address if
there is no DHCP server. If this is the case, contact
your network administrator.
•• With DHCP, the DVR's IP address might change with
each startup.
There is a limit to the number of users allowed to
connect remotely at the same time. Contact the
service center for more information.
• Use FEN: Check if you wish to use FEN service.
• FEN Server: Enter the FEN server’s IP address or
domain name.
If you have configured the DNS Server setting under
Network - IP Address, you can enter the FEN server's
domain name instead of its IP address in the FEN
Server field.
• Port: Specify the FEN server’s port number.
If using an IP router (or NAT), port configuration and
other network functions will depend on the usage
method of the IP router (or NAT).
47
Part 2 - Configuration
• FEN Name: After entering the DVR name you wish
to register on the FEN server, check and register the
entered name. This is a unique DVR name that will be
registered on the FEN server.
RTSP
RTSP service allows you to monitor real-time using the
Real-Time Streaming Protocol.
•• You will not be able to save FEN settings unless you
click on the Check button next to the DVR Name
field and check the entered name's availability.
•• You will be prompted with an error message if you
do not enter DVR name or enter a name already
registered to the FEN Server.
•• If the FEN name contains the #, \, and/or % symbol,
it might not be able to connect to the DVR from the
IDIS Web program.
• Status: Used to check the status of the device being
registered to the FEN server.
Select Save after making changes to register the DVR’s
name to the FEN server.
If FEN has been configured correctly, the FEN server's
help desk information will be displayed in the Help
Desk field the next time you access the FEN Setup
screen.
• RTSP Port: Set the port number of the RTSP server
obtained from your system administrator.
• RTP Port: Set the start/end port number of the RTP
server obtained from your system administrator.
• Use Mobile: Access a remote DVR using a Blackberry
or other mobile devices.
•• Selecting Use Mobile sets the IDIS Web service to
be enabled automatically regardless of your IDIS
Web settings.
•• When using NAT (Network Address Translation) or
firewall services, opening all UDP ports allows you
to access a DVR using Blackberry and Android
devices.
•• You can access a remote DVR and monitor live
video images using media players, such as
VLC Player, supporting RTSP service. Start the
media player on your local PC and enter “rtsp://
ID:Password@IP address:RTSP port number/
trackID=channel number”, or start Internet
Explorer on your Blackberry or other mobile
devices and enter “http://IP address:IDIS Web port
number/”.
•• Some media players might not play video
properly depending on network conditions.
•• RTSP service might not be supported, depending
on the type of media player.
48
Part 2 - Configuration
IDIS Web
VNC
IDIS Web service allows you to monitor and search video
remotely without setting specific on-line programs.
VNC service allows you to access the DVR and control it
remotely using a PC or mobile devices via Ethernet.
• Use IDIS Web Service: Enable/disable IDIS Web.
• Use VNC: Enable/disable VNC. You will be able to
change the settings if Use VNC is enabled.
• Port: Set the port number used when accessing IDIS
Web by using the Up and Down arrow buttons to
increase or decrease the numbers.
• Port: Configure the port number of the VNC server.
• Password: Configure the Password to use when
connecting to the DVR from a remote locale.
Up to three users at a time can access a DVR remotely
via VNC service.
49
Part 2 - Configuration
Key
Function
← or h
Pressing the ← or h key moves to
the left in the menu. It is the same as
pressing the Left arrow button on the
front panel.
→ or l
Pressing the → or l key moves to the
right in the menu. It is the same as
pressing the Right arrow buttons on the
front panel.
↑ or k
Pressing the ↑or k key moves up in the
menu. It is the same as pressing the Up
arrow button on the front panel.
↓ or j
Pressing the ↓ or j key moves down in
the menu. It is the same as pressing the
Down arrow button on the front panel.
m or
Windows
Pressing the m or Windows key displays
the Live Monitoring menu or Search
menu on the screen. It is the same as
pressing the MENU button on the front
panel.
Enter or
Return
Pressing the Enter or Return key selects
the highlighted item or completes an
entry that you have made during system
setup. It is the same as pressing the
Play/Pause button on the front panel.
Pressing the d or PageUp or PageDown
d or
key toggles between different display
PaceUP/
formats. It is the same as pressing the
PageDown
LAYOUT button on the front panel.
c or Home
Pressing the c or Home key allows you to
copy video clips.
F5
Pressing the F5 key refreshes the current
VNC screen.
50
NetFS
It allows you to register NetFS sites for the following
functions:
• Upload or download of files for upgrade, import/
export of a setup file, log export, or file print on a FTP
site. Related settings are as follows:
(Setup) in the live monitoring mode - System
:
menu - General tab - Upgrade, Import, Export
:
(Export) in the search mode - Print
• Upload of clip-copy files on a FTP site. Related
settings are as follows:
(Export) in the search mode - A-B Clip-Copy or
:
Clip-Copy.
• FTP notification of an event detection (system event
excluded). Related settings are as follows:
:
(Setup) in the live monitoring mode Notification menu - FTP tab - FTP setting,
:
(Setup) in the live monitoring mode - Event
menu - Actions – Notify (FTP) setting)
It is recommended that you use FileZilla and smallFtp
servers
This feature is supported only in the PASV(passive
mode) of the FTP site.
Part 2 - Configuration
• Site: Enter NetFS site information.
•• When you delete a FTP site in the NetFS setup
screen on the Network menu, the FTP site in the FTP
setup screen on the Eventupload will be deleted,
too.
•• When you change the usage to other than ALL
or Clip-Copy, a FTP notification function will be
disabled.
•• Select the
Select the Use NetFS to use the NETFS feature. Select the
+ icon at the bottom of the list to add a FTP site up to 16.
• Title: Display the NetFS site name. Use the virtual
keyboard to enter the name.
icon to delete the existing NetFS site.
Entering the NetFS site information using the virtual.Click
the test buton to test the current NetFS site settings you
made.
• Use: Select the usage of the NetFS feature.
–– N/A: disables the NetFS feature.
–– ALL: enables the NetFS feature.
–– Upgrade: It allows you to use the upgrade file
uploaded on the NetFS site.
–– Setup: It allows you to import or export a setup file
uploaded on the NetFS site.
• Address: Enter the NetFS address using the virtual
keyboard.
• Port: Configure the port for connecting NetFS site.
–– System Log – It allows you to save system log on the
NetFS site.
• Remoth path: Enter a folder path in the NetFS site
using the virtual keyboard.
–– Clip-Copy – It allows you to manually copy video
clips to the NetFS site or to automatically copy
event-detected video clips to the NetFS site.
• User / Password: Enter the user and password when
accessing the NetFS site using the virtual keyboard.
• Test: Test the current NetFS site settings you made.
–– Print – It allows you to save images as a PDF file on
the NetFS site.
51
Part 2 - Configuration
Notification Setup
Mail
Configure Mail settings.
Callback
Configure Callback settings.
• +Group: Add a recipient group and select the image
file format attached to an email.
• LAN: Enter the IP address of the receiving server and
set Retry to between 1 and 10 in case of connection
failure.
• Push: Send out event-related messages to mobile
phone.
Enable to receive the event occured in DVR on the
mobile phone(Android, iOS). The DVR must be
registered and set in mobile phone.
52
A virtual keyboard appears allowing you to enter the
Group name. You can select among CBF, JPG, and
MP4. When selecting CBF, the DVR will attach an event
detected video clip to an email. When selecting JPG,
the DVR will attach the event detected image file (JPEG
format) to an email. When selecting MP4, the DVR will
attach the event detected video clip (MP4 format) to an
email.
Part 2 - Configuration
• +Mail: Add a mail recipient.
SMTP Setup
Select SMTP Setup at the bottom right corner of the
screen to configure an SMTP server.
1 Enter the SMTP Server’s IP address or domain name
Assign the Recipient to a Group and enter the Recipient’s
Display Name. Enter the recipient’s e-mail address and
mail server provider. Select the icon to select the mail
server provider from a list of registered SMTP mail server
providers.
The recipient's mail address must be in the correct
email format and contain the @ symbol.
Select the Attach Type icon to attach event recordings
to outgoing mails.
Select the icon to remove the account.
and then configure the Port and Sender settings.
Default SMTP server port number is 25. Select Test to
send out a test mail using the current settings. Select
Use SSL/TLS to use an SMTP server that requires SSL
connections.
•• If you have configured the DNS Server setting
under Network - IP Address, you can enter the
STMP server's domain name instead of its IP
address in the SMTP Server field.
•• Select the
icon to select the mail server
provider from a list of registered SMTP mail
server providers.
•• Address entered under Sender must be in the
correct email format and include the @ symbol.
If user authentication is required by the SMTP server,
select Use and then enter the User and Password
information.
2 Select OK to apply and exit.
This product contains content developed by OpenSSL
Project for use in Open SSL Toolkit (http://www.
openssl.org/).
53
Part 2 - Configuration
SNS
FTP
This option enables the DVR to send out SNS messages.
The SNS (Social Network Service) feature sends out
event-related messages to designated Twitter accounts.
Select the + icon at the bottom left corner of the screen
to add an SNS account. Select the icon on the right
side of the list to remove the SNS account.
Enter the User Name and Password information.
The FTP feature uploads event detected image or video
clip on the FTP site when an event occurs. Select the +
icon at the bottom of the list to add a FTP site.
• FTP: Enter the FTP site information using the virtual
keyboard.
• Uploade File: Select the file format to be uploaded on
the FTP site. the time frame to schedule.
The FTP site can be registered up to 5.
Select the + icon at the bottom of the list to add a FTP
site.
Messages may not be transmitted successfully due to
limitations in Twitter's services.
• Site: Display a list of the registered FTP sites. Select an
FTP site from the list. If the Use setting of the NetFS
site is set to other than ALL or Clip-Copy, you cannot
select the FTP site. You can change the Use setting or
register other FTP sites in the NetFS setup screen on
the Network menu.
54
Part 2 - Configuration
• Uploade File: Select among CBF, JPG, and MP4. When
selecting CBF, the DVR will upload an event detected
video clip on the FTP site. When selecting JPG, the DVR
will attach the event detected image file (JPEG format)
on the FTP site. When selecting MP4, the DVR will
attach the event detected video clip (MP4 format) on
the FTP site.
Schedule
Select the + icon at the lower left corner of the screen to
add a notification schedule.
• Site Information: Displays the FTP site information.
•• For the FTP notification to work properly, the related
settings should be configured:
- Network menu - NetFS tab - Use setting
- Event menu - Actions - EventUpload setting
•• When you delete the FTP site in the NetFS setup
screen on the Network menu, the FTP site in the
FTP setup screen on the Notification menu will be
deleted, too.
•• If many event occurs during a short period, images
may not be uploaded on the FTP site.
• Day: Add different schedules for different days of the
week.
•• The FTP notification is not supported for system
events.
• Range: Change the event notification time frame.
•• If upload fails several times, it deletes the images or
video clips.
•• When the DVR boots, it deletes all images and video
clips even if they were not uploaded yet.
• Notify: Select which notifications to generate when an
event occurs. Select Mail, LAN 1 through 5, SNS, FTP,
Push, and/or Alert Window.
•• In order to use the Notification (Callback) feature,
the DVR must be registered on the remote program.
•• Select the
icon to delete the existing schedule.
• Summary Email Interval: Transmit event summary
emails to a remote destination at specified intervals.
55
Part 2 - Configuration
Display Setup
Status
Refer to the Menu Use on page 20 for basic
information on using the Setup menus.
• Remote Control: The icon
displays when the DVR
can be controlled by the infrared remote control.
OSD
Show OSD (On Screen Display) information on the
bottom of the screen.
• Zoom: The icon
displays on the enlarged video.
• Network: The icon
displays when the unit is
connected to a network via Ethernet. The icon
displays on each camera when audio communication
is available between the DVR and a PC running IDIS
Center via Ethernet. The icon
service is running.
• Freeze & Sequence: The icon
the Freeze mode, and the
Sequence mode.
displays when VNC
displays while in
displays while in the
• Screen Group: Displays the number of screen group.
displays when the DVR is in
• Free Space: The icon
the Recycle mode, and the percentage of available
storage space displays when the DVR is not in the
Recycle mode.
• Date and Time: Displays the date and time.
• User Name: Displays the name of the current user
logged in.
• Background Panel: Displays the background panel at
the bottom of the screen in translucent black.
56
Part 2 - Configuration
Main Monitor
Camera
• No.: Displays the camera number on the upper left
corner of the camera screen.
Configure monitor-related settings.
• Title: Displays the camera name on the upper left
corner of the camera screen.
• Record: Displays recording and schedule icons.
• Audio: Displays the
audio.
• PTZ: Displays the
icon on channels generating
icon on PTZ cameras.
• Text-In: Displays strings received from text-in devices.
Select Display Dwell and specify how long to display
the text-in string. Text-in strings are shown on the
single screen only.
• Transparency: Adjusts the transparency of the setup
screens using the left and right arrow buttons.
• OSD Margin: Displays how OSD text will be displayed
on the monitor. You can adjust the horizontal and
vertical margins so that text and icons will not be
hidden beyond the edges of the monitor.
• Interval: Select between 1 secs and 1 mins. For more
information on Sequence, refer to the Sequence on
page 10.
• Event Monitoring On: With Event Monitoring
enabled, video feed from the camera configured to
start recording when an event occurs is shown on the
screen. For more information on Event Monitoring,
refer to the Event Monitoring on page 16.
• Resolution: Select 1920 x 1080, 1440 x 900, 1280 x
1024.
• Set Resolution to Manual Mode: Set the resolution
manually regardless of the resolution supported by the
monitor.
•• Supported resolutions may be restricted depending
on the monitor.
•• We recommend that you use 1920 x 1080
resolution.
57
Part 3 - Search
Searching Video
While in the search mode, pressing the MENU button
displays the following Search menu on the right edge of
the screen. Pressing the MENU button again hides the
menu. You can navigate through menus and items by
pressing the arrow buttons.
2 Go to
• Go to the First: Displays the first recorded image.
• Go to the Last: Displays the last recorded image.
• Go to the Date/Time: Displays the Go to the Date/
Time screen.
3 Bookmarks
Add the current playback point to the bookmark list.
Search Menu
1
2
The maximum number of bookmarks that can be
saved is 64.
4
4 Display
Used to change the screen layout to single screen
and 2x2.
5
• OSD On/Off: Enables/disables the OSD feature.
3
6
7
8
9
0
!
@
#
58
1 Search
Search by changing Event Log Search, Record Table
Search, Motion Search, and Text-In Search.
5 6 Previous/Next Group
Loads the previous/next screen group.
7 Alarm
Pressing this button while the alarm has been
activated resets all DVR alarm outputs, including the
built-in buzzer.
8 Panic Record
Use the Panic Record feature.
Part 3 - Search
9 Camera Menu
• Zoom: Zoom and choosing the camera number
zooms the current playback image of the selected
camera on the screen.
• Audio: Audio toggles audio playback On and
Off. Recorded audio will be played when the DVR
displays a camera with recorded audio in full screen
mode.
• Hide Text-In: Hide the text-in data on the screen if
the video was recorded with text-in data.
• Edit Group: Enter to the Edit Group mode in the
split screen layout.
Context Menu
Right-click on the Camera screen to access the context
menu.
• Zoom: Zoom in.
• Edit Group: Enter to the Edit Group mode in the split
screen layout.
• Exit Search: Exit the search mode and enter the live
monitoring mode.
The Camera Menu also can be displayed by clicking
the right mouse button on the screen while in the
search mode.
0 Export
• A-B Clip Copy: Designate a start point and an end
point and copy the data in between.
• Clip Copy: Open up the Clip Copy Setup window
for designating points A and B.
• Print: Print a selected image.
! Status
• Allow you to check the status of the DVR’s system,
event status and storage.
Selecting Status will only be enabled for a user who
has System Check authority.
@ Data Source
• Record: Search recording data contained in the
main recording device.
• Other: Search data recorded while disks used in
other systems were connected.
# Exit
Exit the search mode and enter the live monitoring
mode.
59
Part 3 - Search
Event Log Search
Select Event Log Search from the Search menu to bring
up the Event Log Search Setup window.
You can also narrow your event search by selecting
the Option… button and setting up the new search
condition.
You can uncheck the First and Last options at the top
of the Event Log Search window and specify the search
time frame manually.
Select an event to display the recording made on the
selected time and date (paused state). Select the Play
button in the middle of the screen to start playing back
the recording. Use the screen form to load recordings
from other cameras.
Select First for From and Last for To to select the entire
recording from start to end.
If designating From or To settings manually, you will be
able to enable/disable the Check Time Overlap option.
If the system's clock has been changed and the
designated From or To point exists at more than one
location, you will have to choose one. Only the events
that took place between the selected From and To
points will be searched. If Check Time Overlap has
not been selected, events from the entire From and To
range will be searched.
60
Part 3 - Search
Camera Filter
• Alarm-In: Select which channels to search alarm-in
events in.
• Motion: Select which channels to search motion
detection events in.
• Video Loss: Select which channels to search video loss
events in.
• Video Blind: Select which channels to search video
blind events in.
Record Table Search
Select Record Table Search from the Search menu to
bring up the Record Table Search Setup window.
1 2345
6
1 Record Table
Display the current channel’s recording information.
• Text-In: Select which channels to search text-in events
in.
• Record Channel: Select which record channels to
search events in.
Selected record channels are searched for events with
at least one linked recording. If no camera is selected,
only the events with no linked recording camera are
searched.
• Use event filters to include/exclude specific system
events such as Panic Record, Check Recording,
Check Alarm-In, Disk Almost Full, Disk Bad, Disk
Temperature, Disk S.M.A.R.T., Disk Config Change,
and Fan Error from the search.
Recording date and time are shown on the top of the
search window. The indicator line on Record Table
indicates the current playback position. Use the arrow
buttons on the remote control to move the current
playback position in units of individual sectors.
Alternatively, use the mouse to jump to the desired
playback position.
•• Farther back the data is on the record table, the
more recent it is.
•• If the system's clock is changed to a previous
date and time, it is possible for multiple
recordings with the identical time stamp to exist.
Overlapped segments are highlighted in yellow.
Selecting or on the left-bottom of the search
window changes the size of search window and
displays Expanded view(the recording information
of each camera channel), Standard view(combined
recording information of all camera channels), and
Compact view(only the toolbar).
Recording Data Bar Colors
Blue
Time Lapse Recording
Purple
Event Recording
Yellow
Pre-Event Recording
Red
Panic Recording
61
Part 3 - Search
2 Zoom
Select
(zoom-in) to compose recording data
(zoom-out)
in 1-minute segments and select
to compose recording data in 3-minute segments.
Selecting zoom-out displays more time in one screen
than zoom-in screen.
If recording from points in time prior or after the time
frame displayed on the screen is available, scrolls
appear on both ends of the date and time information
line. Scroll using the arrow buttons on the remote
control or by dragging with the mouse to check
recording data.
3 Calendar Search
Use the calendar to search for video recordings by
specific dates.
Dates containing video recordings are highlighted
in black. Selecting a date containing video recording
data loads the earliest recording from that date
(paused state). Selected date is highlighted in light
blue.
4 Search Menu
• Go to: Search video recordings based on date and
time. Specify the date and time and then select Go
to jump to the corresponding video recording.
• Clip-Copy: Clip a video segment and saves it.
• Print: Print the current playback image.
• Zoom: Zoom the current playback image.
• Slow Play: Search the playback screen at low
speeds. Select the desired playback speed (x1/2,
x1/3, x1/4, x1/6, x1/8) and then select Play.
62
5 Bookmark
Add the current playback point to the bookmark list.
The maximum number of bookmarks that can be
saved is 64.
6 Playback Controls
Play and scan through video recordings. Playback
controls have the same functions as their remote
control counterparts.
%
Skips to the previous screen (while in paused
state).
"
Plays the video in normal speed and displays
on the screen. Pressing the button during
playback pauses the video and displays on
the screen.
&
Skips to the next screen (while in paused state).
Scans backward through the video at a fast
rate: X16, X32, X64, X128, X256. (Press to cycle
, and
the speed)
through ,
!
Scans forward through the video at a fast
rate: X16, X32, X64, X128, X256. (Press to cycle
, and
the speed)
through ,
Part 3 - Search
Motion Search
Select Motion Search from the Search menu to bring up
the Motion Search Setup window.
• The Zone setting can be configured in the identical
manner as the Zone setting under System Setup Motion Detection. For more information, refer to the
Motion on page 36.
Museum Search may not function properly if the
edge of the object is included in the Zone. For more
accurate search results, set the inside of the object's
edge as the detection zone.
• Sensitivity: Set to between 1 (Low) and 5 (High).
• Min. Blocks: The Min. Blocks option is available with
Motion Search only.
Once all the options have been configured, select
Search. Select search results entry to display the video
recording on the left. To play the recording, exit the setup
window by selecting Close.
Motion Search cannot be performed while using a split
screen layout. Select Single Screen mode.
Select Option... to configure Motion Search options.
• Select First under From and Last under To to search
the recording from start to finish. Alternatively, you
can uncheck the First and Last options and specify the
search time frame manually.
• Type: Motion Search looks for motion in the selected
area by comparing individual frames against their
preceding frames. This means slow and gradual
movements, no matter how long they persist, will not
be recognized. In contrast, Museum Search looks for
changes in the specified area by using the From frame
as a reference. Museum Search, therefore, recognizes
even minute deviations from the original From frame.
63
Part 3 - Search
Text-In Search
Select Option... to configure Text-In Search options.
Select Text-In Search from the Search menu to bring up
the Text-In Search window.
Select a Transaction to display the video recording
that corresponds to the selected time and date (paused
state).
Text-in information is superimposed on the screen at
normal playback speed. The information is not shown
under any other playback speed.
• Select First under From and Last under To to search
the recording from start to finish. Alternatively, you
can uncheck the First and Last options and specify the
search time frame manually.
Selecting
button, the bookmark list displays
and the bookmark point you selected will be the
starting date and time.
• Channels: Select a channel.
• Select Any Text-In Product to select a device type.
• + : Add a search variable.
• Option...: Select whether or not the search will find
only text strings in which the case matches, find only
exact words that match with the word you entered
during text-in setup, or delete transactions duplicated
within text input strings.
• Load: Retrieve stored search option settings.
• Save: Save the current search option settings.
Once all the options have been configured, select Search
to begin the search and return to the Text-In Search
setup window.
64
Part 3 - Search
Bookmarks
Select Bookmarks from the Search menu to bring up the
Bookmarks Setup window.
Clip Copy
Clip Copy
Select Export – Clip Copy from the Search menu or press
the remote control’s BACK UP button for more 3 seconds
while in Live or Playback mode to open up the Clip Copy
setup window. Specify the From and To settings.
A-B Clip Copy
Select the + icon to add a bookmark to the current
playback position. Use the virtual keyboard to enter the
bookmark name and use the arrow buttons to highlight
the bookmark point for which you would like to see
icon can be used to delete a Bookmark.
video. The
Designate a start point and an end point and copy the
data in between. Select Clip-Copy – A-B Clip Copy from
icon will appear
the Search menu to set point A. The
on the status indicator area on the upper right corner of
the screen. Select Clip-Copy – A-B Clip Copy once again
to set point B. The Clip Copy Setup window will appear.
Select A and B points are automatically applied as From
and To values.
The maximum number of bookmarks that can be
saved is 64.
• Channels: Specify which channel to save the recording
to.
65
Part 3 - Search
• Password: Enable password protection for the saved
video clip and assign a password.
• Dest.: Select which storage media to use. If NetFS
feature is in use, you can upload video clip to the
registered FTP site.
•• In case of clip-copy to the NetFS site, the capacity of
NetFS site and Disk cannot be found.
•• The DVR displays the volume as 30GB regardless of
the actual disk volume and the maximum size limit
on Clip Copy files is 30GB.
•• If the video clip is uploaded after being clip-copying,
video clips will be deleted.
•• If there are same files, the video clips cannot be
copied.
• File name: Designate a name for the file. The name
may be up to 63 characters in length.
Special characters such as \, /, :, ;, *, ?, !, “, <, >, and | are
not permitted.
• Include Text-In Data: Enabling this option will save
the video clip along with any available text-in data.
• Use Site Info: Add Site info to the Clip Copy file’s
name.
Special characters contained in the location info (such
as \, /, :, ;, *, ?, !, “, <, >, and |) will be replaced with _
when the information is added to the file name.
Selecting Start displays a calculation on the size of the
data to be copied. Check the calculation and then select
Continue to proceed. While Clip Copy is in progress, you
can select Cancel to cancel the process or select Close
to allow the window to run in the background. Selecting
Close does not cancel Clip Copy. Once the process is
complete, you will be prompted with a confirmation
window.
66
•• Press the remote control’s BACK UP button for more
3 seconds while in Live or Playback mode to open up
the Clip Copy setup window with One-Touch mode.
•• One-Touch Clip Copy configures the storage range
automatically based on the storage drive's capacity.
If there is insufficient space available on the selected
storage device, you will only be able to Clip Copy
an amount of data equaling the remaining space
available on the storage device.
•• Clip Copying a segment that is more than 2GB in size
produces multiple files that are up to 2GB in size,
each.
•• Clip Copy files can be played back on Windows
systems. For more information, refer to the IDIS
Center operation manual.
•• For USB flash memory devices, the DVR supports the
FAT32 file format only.
Do not disconnect the USB cable or power off the USB
device while USB Clip Copy is in progress. Doing so
can cause the DVR to malfunction or critically damage
the external USB device's file system. You may be
prompted with an error message when trying to back
up on the device. If so, you will need to restart the DVR.
If the USB hard disk's file system has been damaged,
restarting the DVR will not solve the problem and the
aforementioned error message will continue to be
displayed each time you attempt a backup. If this is the
case, you will need to format the HDD or use a recovery
program to repair the damage to the drive's file system.
Part 3 - Search
Print
Print the current image.
While in Search Mode, select Pause to pause playback.
Select Print from the Export to open up the Print Setup
window.
Overlapped Recording Search
If the system’s clock is changed to a point in the past,
overlapping recordings may be produced. Overlapped
recordings have to be searched in segments.
For example, making a recording from 1 o’clock to 5
o’clock, changing the system’s clock at 5 o’clock to 3
o’clock, and then continuing to record until 6 o’clock
produces two recordings that overlap between 3 o’clock
and 5 o’clock. This results in two segments for the period
between 3 and 5.
1:00
Segment 1
2:00
3:00
4:00
5:00
3:00
4:00
5:00
• Printer Model
–– File Printer: Save the current frame to the USB
storage device or the NetFS site as a .pdf file that can
be printed on the printer connected to a computer.
–– PostScript Printer: Print images on a PostScript™
printer connected to the DVR.
Images saved as PDF files can be printed on any printer
connected to your PC.
Segment 2
6:00
When searching overlapped video recordings, you
can choose a specific point in time or a time frame. If
you use the Go to the Date/Time option and select a
point within the overlapped time period (4 o’clock, for
example), you must specify 4 o’clock in which of the two
existing segments.
• Paper Size: Select the desired paper size.
• File name: Designate a name for the file if it is a file
printer.
If you use the Event Log Search or Motion Detection
option and select a time frame within the overlapped
time period (4 o’clock to 5 o’clock, for example), you
must choose between the two redundant sets of From
and To values. Selectable search ranges are as follows:
• 4 o’clock in segment 1 to 5 o’clock in segment 1
• 4 o’clock in segment 1 to 5 o’clock in segment 2
• 4 o’clock in segment 2 to 5 o’clock in segment 2
67
Part 4 - IDIS Web
IDIS Web is a program that allows you to view and search video from remote locations over the Internet and can be
accessed on a regular web browser such as Internet Explorer.
System requirements for running IDIS Web are as follows:
• OS: Microsoft® Windows® XP (Service Pack 3), Microsoft® Windows® Vista (Service Pack 1), Microsoft® Windows® 7
(Home Premium, Professional, Ultimate) or Microsoft® Windows® 8 (Pro, Enterprise)
• CPU: Intel Pentium IV 2.4GHz or above (Core 2 Duo E4600 recommended)
• RAM: 1GB or more
• VGA: 128MB or more (1280x1024, 24bpp or above)
• Internet Explorer: Ver. 7.0 or above (32-Bit)
•• IDIS Web only works with Microsoft Internet Explorer and will NOT work with other browsers.
•• IDIS Web does not work in Microsoft® Windows® 8 metro UI.
1 Launch Internet Explorer and then enter the following information in the address bar.
–– http://IP Address:Port Number (DVR system’s IP address and IDIS Web port number configured under Network >
General (Default Value: 12088))
–– http://fen.idisglobal.com/FEN Name (FEN Name: DVR name configured on the FEN server)
–– http:/web.idisglobal.com (will be prompted to enter DVR’s IP address or FEN name registered to the FEN server
upon login)
Contact your network administrator for the IP address of the DVR you wish to connect to and the IDIS Web port number.
68
Part 4 - IDIS Web
2 When prompted with the IDIS Web login window, select LIVE-PORT or PLAY-PORT as the desired mode. Enter the
ID and password and click LOGIN to sign in using the selected mode.
If connecting by entering http://web.idisglobal.com, enter the DVR’s IP address in the Device Address field.
Selecting the Use FEN Service option on the login window allows you to enter the DVR name registered to the FEN
server instead of its IP address. You will be prompted to enter the FEN server’s address and port number under
Setup.
•• Do not close the login window while IDIS Web is running. Switching over to Web Live or Web Search mode can cause
a script error, requiring you to restart the IDIS Web program.
•• If running IDIS Web, the bottom section of the screen may get cut off if the address bar or the status bar is shown. In
this case, change Internet Options so that the address bar or the status bar is hidden. (Tools → Internet Options →
Security → Custom level... → Allow websites to open windows without address or status bars (Enable))
•• To use IDIS Web on Microsoft Windows Vista or above, launch Internet Explorer by right-clicking on the icon and
selecting the Run as administrator option. Otherwise, certain IDIS Web functions might not be available.
•• Launching a new version of IDIS Web for the first time can cause Internet Explorer to load information from the
previous version. In this case, navigate to Tools → Internet Options → General, delete temporary Internet files, and
then restart IDIS Web.
•• On Microsoft Windows Vista or above, lowered image transmission rate can prevent the screen from being displayed
or updated. In this case, we recommend that you disable the computer's auto tuning function. Open the command
prompt as an administrator. (Start → Accessories → Command Prompt → Right-Click and then select Run as
administrator) Type in "netsh int tcp set global autotuninglevel=disable" and then press Enter. Restart the
computer to apply the change. To enable auto tuning again, launch the command prompt as an administrator and
then type in "netsh int tcp set global autotuninglevel=normal". Restart the computer to apply the change.
69
Part 4 - IDIS Web
Web Live Mode
A remote web monitoring program that allows you to monitor images from remote locales in real-time.
2
3
4
5
1
6
7
8
9
0
!
@
^
#
$
%
Press
2
Place the mouse pointer on the
3
Displays the current time.
4
Select the desired mode. Changing the mode places the selected camera in the first cell of the layout that
will be changed.
5
Click
to print the current video screen using a printer connected to the computer.
6
Click
to save the current video screen as an image file.
7
Click to configure rendering mode and OSD settings. Select rendering mode to adjust the video output
rate or select which OSD elements to display on the screen from the OSD list.
TYPE 1
YPE 1
70
to terminate WebGuard.
1
logo to check WebGuard’s version.
8
Click
to switch over to setup menu.
9
Click
to switch over to Web Search mode.
0
Shows login information.
Part 4 - IDIS Web
!
Select the camera you wish to monitor. Use the arrow buttons to navigate to the previous/next camera
group.
@
Used to control a PTZ camera at a remote location.
#
Used to adjust live video quality.
$
Controls remote alarm out devices.
%
Event status window at the bottom of the screen displays a list of events detected at remote locales.
Select a camera from the screen and right-click to bring up the pop-up menu.
• Change Camera Title: Used to change the camera's name.
Renaming the camera in Web Live mode does not affect the camera's name on
the remote system. If no name is entered for the camera, the name used at the
remote locale is shown on the screen.
• Enable Audio: Enables audio transmission with remote locales. Select to display
buttons.
Enables transmission of audio to the remote locale via microphone.
Enables playback of audio from the remote locale on speakers.
/
Enables two-way audio communication with the remote locale.
Disables audio transmission.
^
If the remote locale connected to supports audio transmission,
screen.
icon appears on the corresponding camera
• Aspect Ratio: Changes the aspect ratio of the video displayed on the screen.
–– Fit to Screen: Fit the video to the size of the camera screen.
–– Fit to Aspect Ratio: Resizes camera screen to original aspect ratio of the video.
–– Half Size (x0.5) - 4 Times Bigger (x4): Displays the camera videos in the selected size based on the
original size of the video. For example, original size (x1) displays the video in its original size. Half size
(x0.5) through 4 times larger (x4) options are only available if there is enough space on the camera
screen to accommodate the selected size.
• Multi Stream: Select a stream.
• Anti-Aliasing Screen: Removes stair step effect (blocks) that is caused when zooming a video to
improve overall quality of video output.
71
Part 4 - IDIS Web
Web Search Mode
A remote web search program that allows you to search for recordings from remote locales in real-time.
While in Web Search mode, connection to remote locales will terminate automatically after 30 minutes of inactivity.
2
3
4
1
5
6
7
8
9
0
!
@
#
$
b
%
^
&
*
(
)
a
Press
2
Place the mouse pointer on the
3
Displays time information of the video recording from the remote DVR.
4
Select the desired mode.
5
Click
to print the current video screen using a printer connected to the computer.
6
Click
to save the video recording as an executable file.
7
Click
to save the current video screen as an image file.
8
Click to configure rendering mode and OSD settings. Select rendering mode to adjust the video output
rate or select which OSD elements to display on the screen from the OSD list.
TYPE 1
72
to terminate IDIS Web.
1
logo to check IDIS Web’s version.
Part 4 - IDIS Web
to switch over to Web Live mode.
9
Click
0
Shows login information.
!
Select the camera you wish to search. Use the arrow buttons to navigate to the previous/next camera
group.
@
Zoom in or out on the video.
#
Adjust image brightness.
Apply image filters (Sharpen, Blur, Equalizer, Interpolation, and Revert)
to the images.
$
Image calibration is applied only during the paused state.
%
TYPE 1
Use the calendar
to search for video recordings by specific dates.
Dates containing video recordings are highlighted in light blue. Selecting a date containing video
recording data loads the earliest recording from that date(paused state). Selected date is highlighted in
orange.
^
to enable time lapse search mode and search/play back video recordings in chronological
Select
order. In Time Lapse Search mode, search is conducted by selecting days on the calendar. The time table
at the bottom displays recording data information for the selected date. Select a point in time to display
video from that moment. If multiple recordings are available for the selected point in time, you can select
the desired segment.
&
Select
TYPE 1
to enable event search mode and search for events matching user-designated parameters.
Use the playback controls to play back video.
TYPE 1
Go to First
TYPE 1
*
TYPE 1
TYPE 1
TYPE 1
TYPE 1
Play by Frame (forwards)
Rewind
Fast Forward
Play by Frame (backwards)
Go to Last
Play/Pause
(
Click
recording.
to designate recent recordings you wish to search and then jump to a specific point in the
)
Click
to reload recent video recordings from remote locales.
a
Indicates the selected camera’s recording data on a time bar. If the camera’s system clock has been
changed to a point in the past and more than one recording exists at the same point in time as a result,
you will be able to choose which segment to search from the segment menu on the upper right portion
of the time table.
73
Part 4 - IDIS Web
Select a camera from the screen and right-click to bring up the pop-up menu.
• Change Camera Title: Used to change the camera's name.
Renaming the camera in Web Search mode does not affect the camera's name
on the remote system. If no name is entered for the camera, the name used at
the remote locale is shown on the screen.
b
• Enable Audio: If audio was recorded with the video, enabling this option plays audio upon playback
(limited to single-screen playback).
• Aspect Ratio: Changes the aspect ratio of the video displayed on the screen.
• Anti-Aliasing Screen: Removes stair step effect (blocks) that is caused when zooming a video to
improve overall quality of video output.
74
Part 5 - Appendix
Index
R
Recording
A
18
S
Alarm-In
38
Search
58
Alarm-Out
43
Storage
30
Audio Recording
19
T
E
Event Monitoring
16
L
LAN
Text-In
40
Text-In Search
64
V
46
Video-Analytics
36
M
Motion Search
Mouse
60, 61
21
O
OSD
56
P
Panic Recording
18
Pre-Event
35
Print
67
V1.1
75
IDIS Co., Ltd.
For more information, please visit at
www.idisglobal.com
">