Wisenet PRN-3205B2, PRN-3205B4, PRN-6405B4, XRN-3210B4 User Manual

Document
NETWORK VIDEO RECORDER
User Manual
Wisenet NVR
Network Video Recorder
User Manual
Copyright
&copy;2022 Hanwha Techwin Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered
trademark of their respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially
or wholly, without formal authorization.
Disclaimer
Hanwha Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee
shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Hanwha
Techwin reserves the right to change the contents of this document without prior notice.
❖ Design and specifications are subject to change without prior notice.
You can download the latest version from the Hanwha Techwin web site. (www.hanwha-security.com)
❖ The initial administrator ID is “admin” and the password should be set when logging in for the first time.
Please change your password every three months to safely protect personal information and to prevent the damage of the
information theft.
Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.
Hanwha Techwin Co., Ltd. is a surveillance camera manufacturer that provides video information equipment with various functions.
Users must comply with local laws when using our devices.
Users are solely responsible for any illegal use of our products.
overview
Important Safety Instructions
Standards Approvals
Read these operating instructions carefully before using the unit.
Follow all the safety instructions listed below.
Keep these operating instructions handy for future reference.
Read these instructions.
2)
Keep these instructions.
3)
Heed all warnings.
4)
Follow all instructions.
5)
Do not use this apparatus near water.
6)
Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.
(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents
as they may deform or cause damage to the product.)
7)
Do not block any ventilation openings, Install in accordance with the manufacturer's instructions.
8)
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9)
Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. if the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
￭ Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
￭ This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
￭ This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
￭ Reorient or relocate the receiving antenna.
￭ Increase the separation between the equipment and receiver.
￭ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
￭ Consult the dealer or an experienced radio/TV technician for help.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
Product User Manual Description
11) Only use attachments/accessories specified by the manufacturer.
This document is a user manual for Recorder product. Before using this product, please read this document carefully in
order to use it properly.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury
from tip-over.
●
This user manual explains how to use the product based on the defaults and default screens of this product.
●
The content of this manual is subject to change depending on the product software updates and the company
policies. It is subject to partial changes without prior notification to users.
Target Audience
This user manual contains contents for Recorder users.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
How to Use the Product
Users of this product can perform the following:
●
Monitor cameras registered to Recorder in real time
●
Search for or play videos saved in Recorder
●
Monitor text data being transmitted to the POS device connected to Recorder in real time
●
Search for text data from the POS device connected to Recorder
●
Monitor real time events that occur in Recorder, sensors, and cameras or search through logs
Before using this product, check if the latest version of this software is installed. Go to Hanwha Techwin's website (http://
www.hanwha-security.com) to check the software version and download necessary files.
English _3
• overview
1)
overview
CAUTION
●
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS.
●
Do not ingest battery, Chemical Burn Hazard.
●
This product contains a coin / button cell battery. If the coin / button cell battery is swallowed, it can cause
severe internal burns in just 2 hours and can lead to death.
●
Keep new and used batteries away from children. If the battery compartment does not close securely, stop
using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part or the body, seek immediate
medical attention.
ATTENTION
●
IL Y A RISQUE D'EXPLOSION SI LA BATTERIE EST REMPLAC&Eacute;E PAR UNE BATTERIE DE TYPE INCORRECT.
METTRE AU REBUT LES BATTERIES USAG&Eacute;ES CONFORM&Eacute;MENT AUX INSTRUCTIONS.
●
Ne pas ing&eacute;rer la pile, risque de br&ucirc;lure chimique.
●
Ce produit contient une pile de type bouton/pi&egrave;ce de monnaie. Si la pile de type bouton/pi&egrave;ce de monnaie est
aval&eacute;e, elle peut causer de graves br&ucirc;lures internes en seulement 2 heures et peut entra&icirc;ner la mort.
●
Gardez les piles neuves et usag&eacute;es hors de port&eacute;e des enfants. Si le compartiment de la pile ne se ferme pas
correctement, cessez d’utiliser le produit et gardez-le d’atteinte des enfants.
Si vous suspectez que des piles ont &eacute;t&eacute; aval&eacute;es ou ins&eacute;r&eacute;es dans une partie du corps, consultez un m&eacute;decin
sans tarder.
4_ overview
Functions Supported by Model
PRN-6405DB4
Fan
O
O
O
O
O
O
O
O
O
P2P
O
O
O
O
O
O
O
O
O
Joystick
O
O
O
O
O
O
O
O
O
Extended monitor
O
O
O
O
O
O
O
O
O
Failover
O
O
O
O
O
O
O
O
O
Alarm
O
O
O
O
O
O
O
O
O
RAID
O
O
O
O
O
O
X
X
X
Distributed recording
O
O
O
O
O
O
O
X
X
iSCSI
O
O
O
O
O
O
O
X
X
AI search
O
O
O
O
O
O
O
O
O
Object detection
O
O
O
O
X
X
X
X
X
LPR search
O
X
O
X
X
X
X
X
X
Power supply redundancy
O
O
X
X
O
X
X
X
X
PoE
X
X
X
X
X
X
X
X
O
Dewarping
O
O
O
O
O
O
O
X
X
Function
AI compatible function
AI recognition function
PRN-6405B4
PRN-3205B4
PRN-3205B2
PRN-1605B2
XRN-6410DB4
XRN-6410B4
XRN-3210B4
XRN-6410RB2
XRN-3210RB2
XRN-6410B2
XRN-3210B2
XRN-1620B2
XRN-1620SB1
XRN-820S
English _5
• overview
PRN-6400DB4
PRN-6400B4
PRN-3200B4
PRN-3200B2
PRN-1600B2
Model name
overview
Contents
overview
3
getting started
10
3
Important Safety Instructions
3
Product User Manual Description
27
Check Event List
3
Target Audience
28
Event Search
3
How to Use the Product
28
Event Instant Viewer
5
Functions Supported by Model
28
Stop Alarm Output
6
Contents
16
Camera Video Control
29
Manual trigger
Capture
10
Starting the system
10
installation Wizard
29
Instant Viewer
13
Camera Setup
30
Temperature Detection Mode
15
Shutting down the System
30
PTZ Mode
15
Restarting the System
31
Zoom In
Login
31
Audio
31
Display Text
32
Change Channel Aspect Ratio
32
Dewarping
16
24
6_ overview
29
Real-Time Event Monitoring
29
15
live
27
Screen Layout of the Live
17
Checking the System Status
18
Check Camera List
19
Live Screen Menu
19
Icons on the Live Screen
20
OSD Information Display
21
Channel Information Display
21
Check the Camera Status
23
Channel Setting
23
Changing Overall Channel Aspect Ratio
24
Full Screen Mode
Setting Up the Live Layout
24
Check Layout List
25
Add Layout and Set Name
25
Delete Layout
25
Change of Layout Channel and Name
25
Dynamic Layout
27
Play Layout Sequence
33
search
36
PTZ Control
33
Getting Started with PTZ Operations
33
PTZ Control Menu
34
Using Digital PTZ (D-PTZ) Function
34
Preset
34
Running Preset
34
Running Swing (auto pan), Group (scan), Tour, or
Trace (pattern)
35
Exporting the Recorded Video
36
Screen Layout of the Search
36
Time Search
37
Event Search
37
Text Search
38
Export Search
38
ARB Search
39
Bookmark Search
39
Smart Search
AI search
play
43
Screen Layout of the AI Search
40
Person Search
70
IP &amp; Port
41
Face Search
71
DDNS &amp; P2P
41
Vehicle Search
73
IP Filtering
42
LP Search
73
HTTPS
42
LPR Search
74
802.1x
74
FTP
E-mail
46
Setting the Network
43
Screen Layout of the Play
75
44
Play Search Results
76
SNMP
45
setup
70
44
Time Line Adjustment
76
DHCP Server
44
Open Time Line Channel
77
Failover
44
Play Button Name and Function
Search Results Export
46
Screen Layout of the Setup
46
Setting the Camera
55
56
62
78
46
Setting the Channel
50
Setting the Camera Functions
51
Setting the Profiles
54
Setting Camera Password
Setting the Recording
55
Record Schedule
55
Record Setup
56
Record Options
starting web viewer
85
85
• overview
40
40
Setting the System
78
Date/Time/Language
79
User
82
System Management
83
Log
What is Web Viewer?
85
Product Features
85
System Requirements
85
Connecting Web Viewer
86
Set the Recorder Password
86
Installation Wizard
87
Camera Setup
88
Screen Layout of the Live Viewer
89
Checking the System Status
89
Checking User ID
89
Checking Camera List
90
Checking the All Camera Status
Setting the Event
live viewer
56
AI Engine
57
Event Setup
59
Event Rule Setup
61
Alarm Input
61
ONVIF Setup
62
Schedule
90
Live Status
Setting the Device
90
Record Status
88
62
Storage Device
90
Network Status
67
Monitor
90
PoE Status
68
Text
English _7
overview
91
Changing the Pattern of Split Screen
91
Changing Overall Channel Aspect Ratio
92
Full Screen Mode
92
Setting up the Live Layout
93
8_ overview
100 Time Search
101 Event Search
101 Text Search
Check Layout List
102 Bookmark Search
92
Add Layout and Set Name
102 Search Results Export
93
Change of Layout Channel and Name
93
Delete Layout
Real-Time Event Monitoring
93
Check Event List
94
Event Search
94
Event Instant Viewer
94
Stop Alarm Output
Live Screen Menu
95
Camera Video Control
99
100
100 Screen Layout of the Search Viewer
92
95
98
search viewer
95
Manual Trigger
95
Capture
95
PC Recording
96
Instant Viewer
96
Microphone Output
96
PTZ Mode
97
Zoom In
97
Audio
97
Image Rotation
97
Channel Aspect Ratio
PTZ Control
98
PTZ Control Menu
98
Using Digital PTZ (D-PTZ) function
98
Preset
99
Running Preset
99
Running Swing (auto pan), Group (scan), Tour, or
Trace (pattern)
Exporting Video
AI search viewer
103
103 Screen Layout of the AI Search Viewer
103 Person Search
104 Face Search
104 Vehicle Search
105 LP Search
105 LPR Search
106 Search Results Export
play
107
107 Play Search Results
107 To Adjust the Time Line
107 Export Video by Section Setup
108 Play Button Name and Function
setup viewer
109 Setting the Camera
109 Channel setup
109 Camera setup
export viewer
124
124 SEC Backup Viewer
124 Recommended System Requirements
124 Screen Layout of the Backup Viewer
• overview
109
109 Screen Layout of the Setup Viewer
110 Profile Setup
111 Camera Password
111 Setting the Recording
111 Record Schedule
111 Record Setup
appendix
126
126 Use Joystick
126 Using Virtual Keyboard
127 Troubleshooting
112 Record Options
112 Setting the Event
112 AI engine
112 Event Setup
114 Event Rule Setup
114 Alarm Input
115 ONVIF Setup
115 Schedule
115 Setting the Device
115 Storage Device
116 Monitor
117 Text
117 Setting the Network
117 IP &amp; Port
118 DDNS &amp; P2P
118 IP Filtering
118 HTTPS
118 802.1x
119 FTP
119 E-mail
120 SNMP
120 DHCP Server
121 Setting the System
121 Date/Time/Language
121 User
122 System Management
122 Log
English _9
getting started
Starting the system
installation Wizard
1. Connect the power cable of the recorder to the wall outlet.
As shown below, proceed through each step of the &lt;Installation wizard&gt;.
Install Wizard can only be accessed at factory reset. If you do not want to proceed, click &lt;Exit&gt;.
2. You will see the initialization screen.
￭ It will automatically change to the optimal monitor resolution and run the install wizard.
￭ If the install wizard does not run, remove the monitor connection from the back of the recorder, reboot the recorder and reconnect the monitor.
The initialization process will last about 2 minute. If a new HDD is installed, the initialization process may take longer.
1. In the &lt;Language&gt; screen, select the language and press the &lt;Next&gt; button.
3. The live screen appears with a beep.
The following symptoms might be observed when starting the system.
￭ If the HDD number is displayed at the bottom of the screen along with &lt;
&gt; while the product is booting up, it indicates that the HDD is in recovery,
and for this reason booting up may take longer.
2. Set the video recording method on the &lt;Storage&gt; screen, and then click &lt;Next&gt;.
HDD 1, 2
￭ If the progress stalls while in &lt;
&gt; state, it indicates that the HDD has problems. Visit your nearest customer service center to check the HDD.
●
Distributed mode : This function is only available for products that support distributed recording.
&lt;Distributed mode&gt; can be selected when there are two or more hard disks. This mode distributes the data and
saves it after the hard disk is formatted.
●
RAID mode : This function is only available for products that support RAID.
&lt;RAID mode&gt; saves data by configuring the hard disk in the RAID format.
●
Single group mode : Saves data on one hard disk. If the hard disk is recognized as an unusable hard disk in the
recorder, the data can be saved after formatting the hard disk.
HDD 2
10_ getting started
3. Set the network connection type and the connection environment on the &lt;Network&gt; screen, and then click the
&lt;Next&gt;.
Setting the camera registration method
This function is only available for products that support PoE. For products that support PoE, refer to the
&quot;Functions Supported by Model&quot; page.
●
Enable PnP mode: Cameras connected to the PoE port of the product will automatically be registered for each
channel in order of port number.
– If the camera's ID and password have already been set, the information that matches the ID and password
set during the &lt;Camera ID/PW&gt; step will be registered (up to 3 sets).
If your camera uses a manual IP, its bandwidth should match with that of Network 1 IP for registration.
– If manual mode is used, it automatically detects and registers cameras connected to the recorder’s PoE port
and cameras connected to a separate switch.
Online Upgrade
You can receive a new firmware notification when the recorder is connected to a network.
Setting up the DHCP server
If you set up the DHCP server to &lt;Run&gt;, the IP address is automatically assigned to your camera.
4. Set the administrator password on the &lt;Recorder ID/PW&gt; screen and click the &lt;Next&gt;.
Click &lt;
&gt; to view the basic guide for setting a password. Refer to the password setup rules.
For more details, refer to the &quot;Setup &gt; Setting the Network &gt; DHCP Server&quot; page in the Table of Contents.
￭ Depending on the camera's state, no IP may be automatically assigned to the camera. After exiting the installation wizard, go to the menu to
assign an IP to DHCP, or set the IP manually.
Setting up the network
Each product supports a different number of network ports. If it supports two or more network ports, you can set
the network for each function as follows. Click &lt;Setup&gt; of the network connected to the recorder.
●
Network 1 (Camera) : Can be used as a port for connecting a camera. If you connect a camera, then the camera
video will be transmitted.
●
Network 2 (Viewer) : Can be used as a port transmitting video to the web viewer. If you access the network
information on your browser, then you can remotely monitor video in your web viewer.
●
Network 3 (iSCSI) : Can be used as a port for an iSCSI connection.
●
￭ Only provided for products that support Network 3.
Network (All) : Can be used as a common port for connecting camera, web viewer, and iSCSI.
– IP type : Allows you to select the type of network access.
– IP Address, Subnet Mask, Gateway, DNS
￭ Manual : IP address, subnet mask, gateway, and DNS can be directly entered.
￭ DHCP : IP address, subnet mask, gateway, and DNS can be automatically set.
￭ If the LAN cable is not connected to the port, &lt;Setup&gt; button will not be activated for use. Check the LAN cable connection.
(In case of a PoE product, Network 1 is activated.)
￭ The built-in DHCP Server in Recorder will turn on automatically at stage 1. At this stage, using the existing DHCP server in the same network
may cause a problem, as two DHCP servers would be simultaneously operating.
￭ A product with multiple network ports cannot use a single bandwidth for all of them.
Example)
–– Port 1 : 192.168.100.199 / Port 2 : 192.168.100.198 (X)
–– Port 1 : 192.168.100.199 / Port 2 : 192.168.101.198 (O)
English _11
• getting started
– When the camera resets to factory default, it defaults to the ID and password set during the &lt;Camera ID/
PW&gt; step. If the camera ID and password are not set, the recorder ID and password will be set automatically.
getting started
5. Set the camera password in factory reset on the &lt;Camera ID/PW&gt; screen.
If ID/PW is already set in the camera, register the ID/PW and click &lt;Next&gt;.
7. On the &lt;Camera register&gt; screen, select a camera to register from the searched camera list and click &lt;Register&gt;.
Select a camera to register from the list and click &lt;Change IP&gt;.
After completing camera register click &lt;Next&gt;.
￭ When the password is in factory reset, it can be changed and managed in a batch.
￭ Up to 3 sets of camera ID with password and password can be registered.
￭ You may change the passwords of registered cameras all at once in the &quot;Setup &gt; Camera &gt; Camera password&quot; menu.
￭ You cannot change the password for cameras registered with ONVIF and RTSP.
6. Set the date, time, and daylight saving time on the &lt;Date &amp; Time&gt; screen, and then click the &lt;Next&gt;.
￭ The time zone setup might differ depending on the region that the product is released.
12_ getting started
￭ After entering the ID and password set in the camera, the connection test must be completed to successfully register.
8. On the &lt;Channel setup&gt; screen, you can view the camera videos registered to each channel in thumbnails along
with thumbnail information. To change the camera video position, select a video and drag and drop it to the desired
location.
After completing channel setup, click &lt;Next&gt;.
9. On the &lt;Easy connect&gt; screen, a remote user can network a recorder in a dynamic IP system.
Click &lt;Enable&gt; to test the connection to see if the current recorder can be connected remotely. When the
connection is successful, a QR code is created.
To connect a recorder via a viewer, select the viewer you want to use. You can check the connection method of the
selected viewer in the popup window.
Camera Setup
When the installation wizard closes, the camera setup screen will automatically appear.
Based on the registered camera's record profile information, you can check the total bandwidth, expected space, and
expected days.
You can change camera setup and the record schedule, and apply the same settings to other channels.
￭ It connects to Wisenet DDNS first. If it does not connect to DDNS, it automatically connects to P2P.
10. Click &lt;Finish&gt; to complete the Installation wizard.
●
Bandwidth/Expected space/Expected days : Displays the total bandwidth, expected space, and the expected days of
the registered camera.
(This may differ from the actual recording content.)
●
Dual recording : You can select whether to use dual recording or not.
●
Apply to other channels : You can apply the settings of the selected channel to other channels in the same way. Select
the desired channel in the “Apply to other channels” confirmation window and click &lt;Ok&gt;.
￭ Applicable only for channels registered with the same camera model.
English _13
• getting started
￭ The camera setup screen is also displayed when registering a camera for the first time in the &quot;Setup &gt; Camera &gt; Channel setup&quot; menu.
getting started
Configuring the Video Environment
Select the thumbnail of the channel whose settings you want to change and click &lt;
that was classified according to the scene will appear.
Configuring the Illumination
&gt;. The setting window
You can click &lt;Setting&gt; to change to the setting you want.
You can select items that are relevant to your channel. A video with more motion may have a higher bitrate,
resulting in a larger expected space and fewer expected days.
Set up the desired type and time.
You can click &lt;
&gt; to change to the setting you want.
●
The bitrate is higher in the following order : Nighttime &gt; Illuminated &gt; Daytime.
●
Revert settings : Reverts to the settings that were set before the user modifies them.
Setting the Recording
You can click &lt;Setting&gt; to change to the setting you want.
●
Expected space/1Day : Displays the expected space based on one day.
●
Revert settings : Reverts to the settings that were set before the user modifies them.
Set up the desired type and time.
14_ getting started
●
Not recording : Do not record for the set time.
●
Continuous, Continuous/Event : Recording is executed for the set time.
●
Event : When an event occurs at the set time, a recording will be executed.
You can set the occupancy (10 to 90) indicating the frequency of movement.
●
Revert settings : Reverts to the settings that were set before the user modifies them.
Shutting down the System
Login
1. Select &lt;Shutdown&gt; at the top right of the screen.
To use the Recorder menu, you are required to login as a user that is authorized to access the applicable menu.
2. The &lt;Shutdown&gt; window will appear.
1. Select &lt;Login&gt; at the top right of the screen.
3. Click on &lt;OK&gt;.
2. The &lt;Login&gt; window will appear.
Restarting the System
1. Select &lt;Restart&gt; at the top right of the screen.
2. The &lt;Restart&gt; window will appear.
3. Enter the user ID and password, then click &lt;Login&gt;.
• getting started
The system will shut down.
￭ The initial administrator ID is &quot;admin&quot; and you will need to configure the password in the installation wizard.
￭ Please change your password every three months to safely protect personal information and to prevent the damage of the information theft. Please,
take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.
￭ For more information about limited-access permission, refer to the &quot;Setup &gt; Setting the System &gt; User&quot; page in the Table of Contents.
3. Click on &lt;OK&gt;.
The system will restart.
￭ Only the user with the &quot;Shutdown/Restart&quot; permission can shut down or restart the system.
￭ To manage Permission Setup, refer to the &quot;Setup &gt; Setting the system &gt; User&quot; page in the Table of Contents.
English _15
live
Shows the video of the camera connected to the recorder. Also, you can adjust the camera and check the network
transfer status.
Item
Description
Saves the recorded video of the selected channel in the designated path.
Screen Layout of the Live
Clears the alarm in the event list and stops the alarm/beep sound for the system status when it is emitted.
The live screen is built as follows.
Activates the manual recording function of the recorder.
Displays information of the OSD screen on the video window.
Shows channel information.
Shows the status of all cameras connected to the recorder.
Removes all screens from the video window.
/
Shows the video in its original aspect ratio or full screen.
It changes to full screen from the current split mode.
Shows the video of the camera connected to the recorder.
●
You can change to single screen by double-clicking the desired video in Split mode. To move to the previous or
next video, click the or button that appears when you mouse over the center of the left or right side of the
video.
●
If you double-click the video in single screen, it will change to split screen.
Video window
Item
Menu
List/Event
Description
●
●
Layout list
PTZ control
●
List : Select to check the camera list.
Event : Select to check the event list
: Mutual authentication connection using WISENET device certificates
: Mutual authentication connection without WISENET device certificate
●
– : Connection without mutual authentication
●
No viewer connected: Displayed when there is no viewer connected to the recorder.
The list of cameras registered in the recorder is displayed.
The ID of the connected user is displayed.
You can also register the camera manually or automatically.
The &lt;Logout/Restart/Shutdown&gt; menu will appear if you click.
●
●
Event List
●
Click each menu to go to the corresponding menu screen.
●
Camera list
Displays the IP address and mutual authentication status of the viewer receiving the video from the recorder.
: Registers the camera manually.
Displays a QR code to download the user manual.
: Searches and registers the camera connected to the recorder automatically.
: The &lt;
&gt; icon is displayed when you mouse over the camera list. Click the icon to go to the camera
web page.
To go to the camera webpage, you must have the right to set channels, profiles, and events, and set &lt;Video&gt; to
&lt;On&gt; in the &quot;Setup &gt; Camera &gt; Channel setup&quot; menu.
Changes the color theme of the screen.
Stops the alarm/beep sound for the system status when it is emitted.
A list of events that have occurred on the camera is displayed.
Displays the default layout and a list of created layouts.
You can also set and play a sequence of layout lists.
System status display
Displays the status of the system, hard disk, and network.
2020-09-27 10:31:20
Displays the current time and date.
Controls the connected PTZ camera.
￭ If the camera's frame rate is set to 60 fps, the frame rate could be reduced on the live screen depending on the monitor resolution output.
16_ live
Checking the System Status
Item
The icon at the top of the screen indicates the status of the system.
Description
Displayed if the server has firmware to update.
It is displayed when the system is overloaded.
￭ Limit the number of users remotely monitored by Web Viewer or VMS, or control the number of events displayed in the event list
• live
of the recorder.
Displayed when manually recording a video while the access restriction for stop recording is enabled.
Only a user with the permission to stop recording is allowed to stop recording.
Displayed when exporting a recorded video in live mode.
Displayed when there is software to update on the camera.
Displayed when playing the layout sequence.
Item
Description
Displayed when running automatic switching of the split screen.
It is displayed when there is a problem with the fan.
￭ Only provided for products that support fans. (Refer to the &quot;Functions Supported by Model&quot; page.)
Displayed when an error occurs in the internal memory.
It is displayed when there is a problem with the power supply.
￭ Only provided for products that support power supply redundancy. (Refer to the &quot;Functions Supported by Model&quot; page.)
Display when recording data is not properly saved.
Error Information
●
If the built-in HDD is not connected, the &quot;NO HDD&quot; icon (
) will be displayed. You must contact the service
center since the Recording, Play, Export, and Upgrade functions do not work while doing this.
●
If you do not format a purchased HDD in a format supporting Recorder, a &quot;NO HDD&quot; icon (
) will be
displayed. If the &quot;No HDD&quot; icon is displayed, check the hard disk connection status in &quot;Setup &gt; Device &gt;
Storage device&quot; and format the hard disk.
●
If a product with a fan does not work or has a problem with the fan, &lt;Fan Information Window&gt; appears and
the fan malfunction icon (
) is displayed. In this case, check the fan inside the product. If the fan is defective,
it can shorten the product life cycle, so please make sure to contract service center nearby.
Displayed if the HDD is full and the Recorder has an insufficient space to record.
Displayed when there is no HDD or HDD is not detected.
Displayed if the HDD needs a technical examination.
It is displayed when RAID contains a malfunctioning HDD or cannot be used due to HDD malfunction.
￭ Only provided for products that support RAID.
It is displayed when recovering a RAID Error.
￭ Only provided for products that support RAID.
￭ If an abnormal fan (
) icon or NO HDD (
) icon, HDD FAIL (
) icon is displayed, contact our customer service.
Appears when input data rate per channel exceeds the specified data rate limit.
It is displayed when an ISCSI device is disconnected.
￭ Only provided for products that support iSCSI.
It is displayed when the network is overloaded.
￭ It occurs when the max receiving allowance is exceeded, causing an overload to the CPU. It disappears when you modify the
Delete Camera or Set Camera to reduce the data rate.
English _17
live
Check Camera List
Check Multichannel Cameras List
Displays the camera type, status, and name registered in the recorder.
For multichannel cameras registered with the Wisenet protocol, the channel information will be displayed under
the model name of the multichannel camera.
Registered channel
(recording channel)
Itrem
Channel information
Unregistered channel
(virtual channel)
Description
Displays channel information (channel number, video window assignment, and color indication).
Displays a normal camera.
Camera type
Displays a PTZ camera.
Recording an event video.
Camera status
Subchannels in which recording is not required do not need to be registered on the recorder, as they can be
monitored real time. However, recording, event reception, or camera settings are not available.
Recording a general video.
Displays the camera error status.
Camera name
In case of multichannel cameras, only one main channel can be registered for recording.
Registered channel
(recording channel)
Unregistered channel
(virtual channel)
Unregistered channel
(virtual channel)
Unregistered channel
(virtual channel)
Displays the name set for the camera.
￭ If a camera connection error occurs, it is disabled in the list.
￭ The camera status display information changes according to the network connection status and settings.
18_ live
Unregistered channel
(virtual channel)
Live Screen Menu
Icons on the Live Screen
After selecting the desired channel on the split mode, roll the mouse cursor over the screen to see the live screen
menu.
You can check the status or operation with the icons on the live screen.
The live screen menu appears differently depending on the recorder operation status or the type of the
registered camera.
￭ The icons displayed on the screen may differ depending on the type of camera and the user's authority.
• live
￭ Each function may be restricted depending on the type of camera and the user's authority.
￭ For more detailed information about each function, refer to the table of contents &quot;Live &gt; Camera Video Control&quot;.
Item
Item
Description
Manual trigger
Capture
Instant Viewer
If the event action for &lt;Manual trigger&gt; is set for the selected channel, the event rule name is
displayed when you hover the mouse over &lt;
&gt;. Click &lt;
&gt; to activate the set event.
: Displays the event recording.
●
: Displays the normal recording.
You can rewind 30 seconds while monitoring the video.
Displayed when the resolution of the live video exceeds the supported range while the
camera is on.
PTZ control
If the network camera connected to the selected channel supports the PTZ function, it changes to
the PTZ control mode.
Zoom in
You can zoom in or zoom out the video.
Audio
Turns the audio on or off when the audio is connected.
Dewarping
●
Displayed when there is no input while the camera is on.
For images that support the thermal imaging camera function, you can click the desired point to
check the temperature information.
Channel aspect ratio
Displays camera's recording status and name.
Recording status and camera name
You can take a screenshot of the selected channel.
Temperature Detection
Display Text
Description
Video input status
Displayed if no permission to live view is granted.
Displayed when the camera is not registered.
If you set the channel setup to &lt;Covert2&gt;, nothing will be displayed on the live screen.
￭ If you set the channel setup to &lt;Covert1&gt;, the video will not displayed on
the live screen, but only the OSD will be displayed.
Turns the text output on or off.
Shows the video in actual proportions.
Enters the setup mode for dewarping the fisheye camera.
￭ It works only when the video resolution is 1:1. Some models do not support this function.
English _19
live
Item
Event Display
Description
Events from the recorder and camera are displayed in icons.
You can show or hide the recording status, camera status, event display, etc. in the video window.
For details, refer to the &quot;Setup &gt; Setting the Event &gt; Event rule setup&quot; page in the
Table of Contents.
To show or hide the OSD information, click &lt;
It is displayed on the channels that can enable the PTZ mode.
Displays AUDIO ON/OFF.
It will not be displayed when &lt;Off&gt; is selected for the audio in the channel setup.
If the alarm in is set, it is displayed on the connected channel when an external signal is
entered.
If the event detection is set for each channel, it is displayed when a camera event occurs.
It is displayed when it fails to decode all the frames due to limited decoding performance
and in this case only the I-Frame is decoded.
Status Display
This is displayed when a POS (text) event occurs.
Displayed when there is an error with the SD card.
Displayed when the SD card capacity is full.
Displayed when a defocus event occurs.
Displayed when a fog detection event occurs.
Displayed if the Wisenet camera's certificate is valid.
￭ The 'Live4NVR' profile is added automatically with network camera auto registration, and settings can be changed according to user
environment.
￭ Depending on camera specification, you may not be able to add a profile or if you have the PLUGINFREE profile, you will not be able to add the Live4NVR
profile.
￭ When system overloaded and the performance is down, network camera may play only main frame(I-frame).
￭ To set profiles, refer to &quot;Setup &gt; Setting the Camera &gt; Setting the Profiles&quot; page in the Table of Contents.
20_ live
OSD Information Display
&gt; at the bottom of the screen.
Channel Information Display
Check the Camera Status
You can check the information of the video being recorded with each camera.
You can check the status of all cameras connected to the recorder.
To check the channel information, click &lt;
To check the camera status, click &lt;
&gt; at the bottom of the screen.
&gt; at the bottom of the screen.
• live
The information of the current video is displayed on the live video which is being monitored.
Live Status
800x448 (H.264)
Select &lt;Live&gt; in the &lt;Status&gt; menu to check the transmitted data from a network camera connected to each
channel.
S/I/D 25/24/24
XNV-6081Z(S)
●
800x448 : Displays the resolution of the video.
●
H.264 : Displays the video codec.
●
S/I/D 25/24/24 : Displays the frame rate (FPS) of the video. (S : Settings, I : Video input, D : Video display)
●
XNV-6081Z : Displays the camera model name.
●
CH1 : For multi-channel cameras, the channel number is be displayed. The channel number may not be
displayed depending on the camera.
●
S : Displays the protocol used when registering the camera.
– S and V represent Wisenet protocol while O represents ONVIF.
– When connected by RTSP protocol, only RTSP is displayed without the product name.
￭ ARB is only visible when an ARB situation occurs.
●
Model : Displays the model name of camera connected to each channel.
●
Status : Shows the connection status of camera set to each channel.
●
IP address : Displays the IP address of a camera set to each channel.
●
Codec : Displays the live profile codec information for a camera set to each channel.
●
Resolution : Displays the live profile resolution of a camera set to each channel.
●
Frame rate : Displays the live profile transmission rate for a camera set to each channel.
English _21
live
Record Status
Network Status
If you select &lt;Record&gt; in the &lt;Status&gt; menu, you can check the profile, record type, frame rate (Input/Record),
and bit rate (Limit/Input/Record) for each channel.
Select &lt;Network&gt; in the &lt;Status&gt; menu to check the status of network bandwidth currently being received/
transmitted.
●
Total bitrate (record/max) : Record shows the amount of data currently being recorded, and Max shows the
amount of recorded data allowed for the recorder.
●
Current : Shows the recording status information of currently transferred data.
●
Max : Shows recording information of the most biggest recording data out of configured standard and event
recordings.
: Reloads the recording information.
●
●
Profile : Shows the video profile configured to each channel.
●
Record : View the record type according to normal or event recording.
●
Frame rate (fps) : Shows the receive/record frames per second for each channel.
●
Bitrate (bps)
￭ Each product supports a different number of network ports.
PoE Status
This function is only available for products that support PoE. For products that support PoE, refer to the
&quot;Functions Supported by Model&quot; page.
Select &lt;PoE&gt; in the &lt;Status&gt; menu to check the current PoE status of each port.
– Limit / Receive / Record : Shows the amount of limit/receive/record data for each channel.
– Receive/Limit : Shows the data ratio of actual data transferred from the camera and allowed maximum
defined by user.
●
Record setup : You can set detailed recording settings.
For more details, refer to the &quot;Setup &gt; Setting the Recording &gt; Record Setup&quot; page in the Table of Contents.
￭ If an error occurs during recording, the channel's profile column turns yellow.
This profile error indicates that when a recording profile cannot be used to receive video from camera, an alternative profile is used to record the
video. When the recording profile resumes, the camera video can record by using the set recording profile.
￭ If Recorder exceeds the recording limit, only the key frame will be recorded. In that case, a restricted recording popup and an icon will appear.
The restricted recording popup appears only once. If you change the camera setup and record setup, the restricted recording popup may appear
once more to confirm the status.
If you don't want to see it again, then check Do not show this again in the popup.
For the maximum allowed number of recoding, refer to the &quot;Setup &gt; Setting the Recording &gt; Record Setup&quot; page in the Table of Contents.
￭ For dual recording, the bitrate is shown as the sum of recording and remote profiles.
However, the &lt;Enable dual recording&gt; box in the &quot;Record &gt; Record options&quot; menu must be checked.
The recording profile and remote profile can be set in the &quot;Camera &gt; Profile setup&quot; menu.
22_ live
●
Consumption (W) : Displays the power consumption in PoE.
– 0 : No device is connected to the port or device is using its own power supply.
– – : Port failure (Failure information is displayed in Detailed information.)
CH1
●
CH2
CH2
CH1
CH2
CH4
CH5
CH7
CH2
CH8
CH2
CH3
CH3
CH10
CH6
CH13
CH11
CH12
CH1
CH14
CH15
CH9
CH16
CH3
CH4
CH4
CH5
CH2
CH3
CH5
CH4
Changing Overall Channel Aspect Ratio
CH3
CH6 supply toCH7
CH7
CH3
Enable: Turns on/off
the CH6
power
the camera.
CH1
– Checked
(
CH1
CH4
CH8
CH1
CH8
CH1
CH19
): Power
supply
available
CH4
CH5
CH6
CH7
CH6
CH7
CH8
CH11
CH12
– Not
checked
(
CH5
CH10
CH10
CH11
CH12
CH10
CH11
CH12
CH13
):CH8Power
supply
limited
CH19
CH13
CH1
CH1
CH2
CH2
CH1
Video screen ratio for all channels can be changed in live split screen mode.
CH1
CH5
CH6
CH9
CH10
CH13
CH14
CH7
CH8
CH11
CH12
CH15
CH16
Detailed
information:
If there is a problem with power supply, it is described here. Power supply problem
CH13
CH14
CH15
includes overload power (Class 1 to 4) and voltage fault.
●
CH16
●
Total power consumption (W): Displays the sum of power consumption of all ports.
CH1
CH1
CH2
CH1
CH2 CH2
CH3
CH3
CH3
CH8
CH1
CH5
CH6
CH7
CH9
CH10
CH11
CH12
CH13
CH14
CH12
CH15
CH16
CH7
CH2
CH3
CH4
CH5
CH6
CH1
CH8
CH9
CH10
CH11
CH12
CH13
CH14
CH15
CH16
CH2
CH13
CH2
CH14
ToCH1switch
channel,
holdCH8a channel
andCH4drop
CH1 the position of a CH7
CH3
CH4it to the desired location.
CH7 CH8
CH9 and
CH3 drag
CH9
CH8
CH11
CH1
CH2
Click &lt;
&gt; to return to the previous aspect ratio.
CH4
CH1
CH5
CH6
CH9 CH5
CH10 CH6
CH4
CH4in a
CH6
You
can display
the channel
desiredCH5area
of a split screen.
CH7
&gt; at the bottom of the screen. It changes to the actual proportion of the video.
• live
Channel Setting
Click &lt;
CH15
CH3
CH16
CH1
Example) If switching CH 1 to CH 7
CH1
CH10
CH2
CH3
CH4
CH10 CH11
CH11 CH12
CH5
CH6
CH7
CH8
CH13
CH9
CH13 CH14
CH14 CH15
CH10
CH11
CH12
CH16
CH13
CH16
CH14
CH15
CH16
CH7
CH2
CH3
CH4
CH5
CH6
CH1
CH8
CH10
CH11
CH12
CH15
CH3
Switching
to Single
ModeCH9
CH5
CH6
CH5
CH6
CH9
CH10
CH10
CH1
CH2
CH1
CH13
CH13
CH14
CH14
When in split mode, select and double-click a desired channel to switch to its Single mode.
CH9
CH7
CH13
CH7
CH14
CH1
CH5
CH12
CH8
CH15
CH8
CH16
CH1
CH2
CH2
CH3
CH3
CH4
CH4
CH5
CH6
CH6
CH7
CH7
CH8
CH8
CH9
CH9
CH10
CH10
CH11
CH11
CH12
CH12
CH13
CH13
CH14
CH14
CH15
CH15
CH16
CH16
CH7
CH7
CH2
CH2
CH3
CH3
CH4
CH4
CH5
CH5
CH6
CH6
CH1
CH1
CH8
CH8
CH9
CH9
CH10
CH10
CH11
CH11
CH12
CH12
CH13
CH13
CH14
CH14
CH15
CH15
CH16
CH16
CH11
Example) If double-clicking CH 3
CH11
CH12
CH12
CH15
CH15
CH16
CH16
CH1
CH1
CH2
CH2
￭ You can change the aspect ratio of each channel. For more information, refer to the &quot;Live &gt; Camera Video Control &gt; Change Channel Aspect
Ratio&quot; page in the Table of Contents.
CH3
CH3
CH1
CH1
English _23
live
Full Screen Mode
Setting Up the Live Layout
You can change to full screen mode, which has no top/bottom/left/right areas of the live screen.
This section outlines how to select a series of channels based on their purpose/accessibility and monitor them in a
single layout.
Click &lt;
&gt; at the bottom of the screen.
Example) Layout &quot;Lobby&quot; - Lobby camera 1, Lobby camera 2, Front entrance camera 2
Layout &quot;VIP&quot; - Directors' meeting room 1, Directors' meeting room 2, Directors' lounge 1, Corridor camera on
the 7th floor
￭ After the software upgrade, the previously set layout may be changed. Reset the layout and sequence.
Check Layout List
Click &lt;
List &gt; at the top left of the live screen, and then click &lt;
Changes to full screen mode.
￭ To exit full screen, place your mouse cursor over the bottom of the full screen mode and click &lt;
General mode
&gt;.
Full screen mode
●
24_ live
: Create a new layout.
●
: Save the changed layout.
●
: Saves the selected layout with a different name.
●
: Delete the added layout.
●
/
●
: Change the name of the layout.
: Open or close the layout list.
&gt; to display the layout list.
Add Layout and Set Name
Dynamic Layout
1. Click &lt;
&gt; to add a layout.
You can set the size and position of the video assigned to the layout as desired.
2. Click &lt;
&gt; to set the name for the added layout.
￭ You can simultaneously assign multiple consecutive channels from the camera list to the video window. Drag the desired channels from the camera
list and drop them on the video window. Depending on the drop location and the number of channels, empty area or the current layout will be
expanded to assign the video.
4. Click &lt;
&gt; to save the set layout.
￭ Each layout is saved separately by the user.
￭ The layout set on the live screen can also be used for time search and can be searched according to the channel order and channel combination
• live
3. Double-click or drag and drop a channel from the camera list to display it on the layout screen. The selected
channel will be displayed in the video window.
￭ The dynamic layout function can only be set on the primary monitor.
Assigning One Channel
Double-click or drag and drop a channel from the camera list to display it on the layout screen.
The video is assigned to the empty area or depending on the drop location, the current layout will be expanded
to assign the video.
Example) When assigning 9 channels to a new layout, the channels are arranged in the order below.
set by the user. For more information, refer to the &quot;Search &gt; Time Search&quot; page in the Table of Contents.
Delete Layout
Click &lt;
&gt; after selecting the layout to delete.
Double-click
￭ You cannot delete the default layout.
Change of Layout Channel and Name
1. Click &lt;
&gt; after selecting a layout.
2. Add or delete channels or rename layouts.
3. Click &lt;
&gt; to save the changed settings.
Assigning Multiple Channels at once
Drag multiple consecutive channels from the camera list and drop them into the video window.
Depending on the drop location and the number of channels, the videos will be assigned to empty areas or the
current layout will be expanded to assign the videos.
Example) When assigning 9 consecutive channels to a new layout, the channels are arranged in the order
below.
Drag and drop
English _25
live
Zooming In and Out of Videos
Moving Videos
You can enlarge or reduce the video by dragging a corner or vertex of the video in the desired direction.
If you double-click the corner or vertex of the enlarged video area, the video will be reduced step by step.
To move the video, click the video and then drag and drop it in the desired location.
Dragging it outside of the layout area will expand the layout area.
The video can be enlarged if there is an expandable blank area around the video.
Horizontal zoom
The enlarged video can be moved only when there is an empty area that is the size of the video.
Vertical zoom
Diagonal zoom
26_ live
Play Layout Sequence
Real-Time Event Monitoring
You can automatically switch the layout list to a set time interval to view.
Real-time events that occurred on the camera can be checked in the live video window and event list.
Sequence Setting
Click &lt;
&gt; at the bottom of the layout list to set the sequence.
￭ AI events are only available for products that support AI.
￭ AI events are displayed only after setting event rules. AI event search may have different settings and operation specifications depending on the recorder
or camera.
• live
Check Event List
Click &lt;
Event&gt; on the left side of the live screen to display the real-time event list.
￭ When new events occur, the list of events will be updated accordingly.
￭ The specified channels and events are displayed in the list according to the event rule setup.
For details, refer to the &quot;Setup &gt; Setting the Event &gt; Event rule setup&quot; page in the Table of Contents.
●
Sequence switching time : Set the switching time of the layout list.
●
Sequence list : Set the layout sequence playback order. You can add the same layout repeatedly.
Play Layout Sequence
Click &lt;
Play sequence&gt; at the bottom of the layout list to automatically switch the layout according to the
sequence settings.
●
: Browses for the event by the desired condition.
●
: Plays the video at the time of the event.
￭ When an alarm output occurs, if event recording is set and pre-event time and post-event time are set, event recording is performed before or
after the event according to the set recording method. For more information about event recording settings, refer to the &quot;Setup &gt; Setting the
Recording &gt; Record setup&quot; page in the Table of Contents.
￭ The video may be delayed depending on the network condition.
￭ The event output can be delayed as the transfer of the alarm event from the network camera takes time.
￭ &lt;Play sequence&gt; is active only when a sequence is set.
English _27
live
Event Search
Event Instant Viewer
You can browse events by camera and event type.
To search for a specific event, click &lt;
&gt; to select the event type and camera to browse.
Event filter
Displays only selected events in the event list.
Select an event to check from the event list, and click &lt;
occurred.
&gt; to play the recorded video at the time the event
￭ Instant viewer can play an event video for 1 minute.
￭ For AI events, the best shot and details of the event that occurred are displayed.
￭ AI event recognition may have different settings and operation specifications depending on the recorder model or camera.
￭ To see AI events, set any of the following options as necessary : See the relevant page for detailed setup method.
–– Setup &gt; Event &gt; AI engine
–– Setup &gt; Event &gt; Event setup &gt; Object
–– Setup &gt; Event &gt; Event setup &gt; AI recognition
–– Setup &gt; Event &gt; Event setup &gt; Mask
–– Setup &gt; Event &gt; Event setup &gt; IVA
–– Setup &gt; Event &gt; Event rule setup
AI event
●
Common event : Searches for event types that have occurred in general cameras such as motion detection and
IVA.
●
AI event : Searches for AI event types such as face, person, and vehicle.
Common event
￭ AI events are only activated when an AI camera is connected.
￭ AI events are displayed only after setting event rules. For details, refer to the &quot;Setup &gt; Setting the Event &gt; Event rule setup&quot; page in the Table of
Contents.
Camera filter
Displays events for the selected camera only.
●
/
●
: Moves to the playback screen.
: The video is played/paused.
●
: Instant Viewer playback ends.
Stop Alarm Output
When an event occurs, an alarm can occur. Click &lt;
necessary.
&gt; at the bottom of the screen to stop the alarm output if
For details, refer to the &quot;Setup &gt; Setting the Event &gt; Event rule setup&quot; page in the Table of Contents.
28_ live
Camera Video Control
Capture
By using the function icon of the video window, you can easily use the functions of capture, video zoom, PTZ camera
and thermal imaging camera. When you place your mouse over the video window, the live screen menu will appear.
You can take a screenshot of the current video of a specific channel selected on the live screen.
1. Select a channel to capture video and click &lt;
&gt;.
2. Select the output information to be displayed on the captured screen.
• live
Manual trigger
3. Set the device where the screenshot file will be saved and the file name.
If the event action for &lt;Manual trigger&gt; is set for the selected channel in the &quot;Setup &gt; Event &gt; Event rule
setup&quot; menu, the event rule name will be displayed when you hover the mouse over &lt;
&gt;. Click &lt;
&gt; to
activate the set event.
4. Complete the settings and click &lt;OK&gt; then the image captured from the screen is saved to the selected
device.
￭ If you click &lt;Format&gt;, the format confirmation window will appear. Click &lt;Yes&gt; to format the selected storage device.
￭ Camera screen larger than 2 megapixels is captured in Full HD size.
Instant Viewer
You can move the video back 30 seconds and play it while live monitoring. Instant viewer plays video from 30
seconds to 1 minute from the current time.
Select the desired channel and click &lt;
The Instant Viewer screen appears.
&gt;.
Manual trigger 1
●
/
●
: The video is played/paused.
: Moves to the playback screen.
●
: Instant Viewer playback ends.
English _29
live
Temperature Detection Mode
PTZ Mode
For images that support the thermal imaging camera function, you can click the desired point to check the
temperature information.
You can run PTZ control of the selected channel.
Select the desired channel and click &lt; &gt;.
When you place your mouse over the video, the mouse pointer changes to a thermometer shape, and when you
click a specific location on the video, the temperature at that location is displayed next to the mouse pointer.
Enters the PTZ control mode.
Select the desired channel and click &lt;
&gt;.
￭ Depending on the camera, the PTZ control function and speed may be different.
36.5&deg;
●
●
: Exits temperature sensing mode.
: The color of the video changes according to the temperature color selection.
●
: The PTZ mode is closed.
●
: Captures video of the current state.
●
: After clicking the digital zoom icon, you can use &lt;
●
: Returns to the 1x zoom screen.
/
&gt; to zoom in or zoom out the video.
Adjusting the Camera Direction
When you rolls over the mouse to &lt;
&gt;, the 8-way key appears, and when the mouse leaves the area of the
direction key, the direction key disappears. You can fine-tune the camera direction by clicking the 8-direction key
once. Keep clicking the arrow keys to move in the desired direction and release the mouse to stop.
To quickly adjust the direction of the camera, click &lt;
&gt; and drag. The screen moves quickly in the desired
direction. You can adjust the screen movement speed according to the drag distance.
Moving to the Center of the Screen
Click a specific location on the screen to move the video at that location to the center of the screen.
Zooming the Selected Area
Drag a specific area of the screen, to move and the selected area to the center of the screen and zoom in.
Zooming In and Out of Images
You can zoom in or out using the mouse wheel. Click &lt;
30_ live
&gt; to go back to the original size.
Zoom In
Display Text
You can zoom in or out the video via digital zoom.
Select the desired channel and click &lt;
You can monitor texts regarding the sales record received from POS in real time.
￭ This is executable when a text device is connected.
￭ The Recorder can display text on a live screen when a text device is set. For details, refer to the &quot;Setup &gt; Setting the Device &gt; Text&quot; page in
&gt;.
Enters the digital zoom mode.
&gt; to run the digital zoom.
Select the desired channel and click &lt;
• live
￭ In PTZ mode, click &lt;
the Table of Contents.
&gt;.
When text information occurs, the text information is displayed in the corresponding video window.
Also, when a set text event occurs, the corresponding part of the text is displayed in a separate color.
Onions
3.59
CHIP
2.37
Apple
2.69
Goat
0.79
Peppers red, loose 0.59
2 x 0.79
Pasta
2 x 0.59
1.18
0.59
1.18
========================
●
: Exits the digital zoom mode.
●
/
●
TOTAL
3.63
: Zooms in or out the video.
Minimap : When the video is enlarged 10%, a minimap is displayed. You can quickly check the desired location
in the enlarged video through the mini-map.
&lt;
&gt; appears when text information crosses the screen. Click &lt;
can check the entire content.
&gt; to display a popup window where you
Audio
You can turn the sound on/off corresponding to the channel in Live mode.
Select the desired channel and click &lt;
&gt;.
Audio output can only be turned on in one channel. The audio output of other channels will be automatically
turned off.
￭ If you have configured the audio output settings properly but the audio or voice is not output, check if the connected network camera supports
the sound signal and if you have configured the sound settings as appropriate.
The sound icon can be displayed if the sound signal fails to output from noise.
￭ Only the channel where &lt;Audio&gt; is set to &lt;On&gt; in &quot;Setup &gt; Camera &gt; Channel Setup&quot; displays the audio icon (
you can use to turn the sound on/off.
) in Live mode that
English _31
live
Change Channel Aspect Ratio
Dewarping
You can change the aspect ratio of each channel.
You can correct distorted images from the fisheye camera by running dewarping.
Select the desired channel and click &lt;
Select the channel you want and click &lt;
&gt;.
It changes to the actual proportion of the video.
&gt;.
It will enter the setup mode for dewarping.
￭ This function is not supported in some models.
￭ This works only when the video resolution is 1:1.
￭ The set dewarping mode is cleared when the layout is changed, so set it again.
￭ Dewarping will be applied only to the selected channel.
￭ In dewarping mode, the frame rate of the video is limited depending on the resolution (3-30 fps).
●
●
: Dewarping mode is closed.
: You can select from &lt;Single&gt;, &lt;Quad view&gt;, &lt;Single panorama&gt;, and &lt;Double panorama&gt; for the
view mode.
– Single, Quad view : You can use the PTZ function by dragging the mouse up/down/left/right or by using the
mouse wheel.
– Single panorama : You can select when the mounting mode is &lt;Wall&gt;
– Double panorama : You can select when the mounting mode is &lt;Ground&gt; or &lt;Ceiling&gt;. You can use the
PAN function by dragging the mouse left or right.
●
32_ live
: You can select the mounting mode from &lt;Ground&gt;, &lt;Wall&gt;, and &lt;Ceiling&gt;.
PTZ Control
Item
With this Recorder, you can configure the settings of a PTZ camera as well as commercial cameras in the market to your
preference.
Description
Zoom out/Zoom in
This is active only if a channel that a PTZ camera is connected to is selected.
Near/Far
You can adjust the focus manually.
Auto focus
You can adjust the focus automatically.
Preset
Set the preset position to move the camera, and then select the desired preset to move to the
set position.
Swing
Swing is a monitoring function that moves between two preset points and enables you to
trace the motion.
Group
The group function enables you to group various presets before calling them in sequence.
Tour
Monitor all the groups created by a user in turn.
Trace
Tracking remembers the trace of movements that you instructed and reproduces it for your
reference.
The PTZ camera will be activated only if the channel of the PTZ camera is selected. After selecting the desired
channel, click &lt;
&gt; on the live screen menu.
￭ This is available only if a PTZ camera is connected and the &lt; &gt; icon is displayed on the screen.
￭ Even if the connected network camera does not support the PTZ operations, you can configure the PTZ control settings (if possible) by installing
the PTZ driver (physical device).
￭ It only supports a network camera with Hanwha Techwin's PTZ function and a camera registered in the ONVIF.
PTZ Control Menu
You can use a single PTZ camera to perform the Pan, Tilt and Zoom operations to monitor multiple places, and
configure the custom settings of the presets in a desired mode.
Click &lt;PTZ control
below.
&gt; on the bottom left of the live screen to display the PTZ camera control menu as shown
The preset you set is saved and displayed in the list.
Deletes the selected preset list.
Preset List
Shows a list of saved presets.
￭ The PTZ working (active) mark can be active even if the PTZ operation is not available in normal mode. So ensure that you have completed the
PTZ settings before proceeding.
￭ Some cameras may differ in the menu title and operation with regard to Swing, Group, Tour and Trace.
￭ Even if your network camera supports the function, you can use it only if the button is activated in the PTZ control launcher.
English _33
• live
Getting Started with PTZ Operations
Activate the Zoom operation of the PTZ camera.
live
Using Digital PTZ (D-PTZ) Function
To delete a registered preset
1. Register a camera that supports the D-PTZ profile.
1. Click &lt;
&gt;.
2. Click &lt;
&gt;. &lt;Delete preset&gt; window will appear.
￭ In cameras that support the D-PTZ profile, you can use the D-PTZ function.
2. Both cameras that support general PTZ and cameras that support D-PTZ can control the live image using
some of the &lt;PTZ control&gt; function menus.
￭ For more information about the supported functions, please refer to the camera manual.
Preset
3. Click &lt;
Preset is a set of saved data specifying the locations of a PTZ camera. A single PTZ camera can save up to 300
locations.
￭ The max. number of presets may vary depending on the number of presets supported by the camera.
4. Click &lt;Delete&gt;. The selected preset will be deleted.
Running Preset
1. Click &lt;
To add a preset
1. Select the desired channel and click &lt;
￭ The PTZ control screen appears.
&gt;.
2. Use the arrow keys to adjust the camera to the point.
3. Click &lt;
5. Click &lt;
&gt;, the &lt;Preset setup&gt; window will appear.
&gt; to select the Preset Order to set.
6. Enter the Preset name.
7. Click &lt;Save&gt;.
The preset setting will be saved.
￭ If you replace a camera that saves your preset settings with a different one, you must configure the preset settings again.
34_ live
&gt;.
2. Click the preset you want to run from the list.
The camera lens moves to the set position.
Running Swing (auto pan), Group (scan), Tour, or Trace (pattern)
The running method of each function is the same as the preset operation method. For details on how to use it,
refer to the camera's user manual.
&gt;.
4. If you click &lt;
&gt; to select the preset to delete.
￭ Depending on the camera's capabilities, only some features may be available.
Exporting the Recorded Video
You can search the storage device to be exported and export the recorded video of the desired time by layout or
channel.
1. Click &lt;
&gt; at the bottom of the screen.
2. The export setup screen will appear.
3. After completing the export setup, select &lt;Start&gt;.
￭ If there is no device to export, the &lt;Start&gt; button will be deactivated.
￭ If you click &lt;Stop&gt; during the export progress, which is the export will be canceled.
4. Click &lt;OK&gt; on the export completion confirmation window to finish.
Format the memory stick or delete some of the data on the memory stick to secure adequate storage space.
￭ The operation speed of the product may slow down if the export is in which is a progress.
￭ You can switch to the menu screen during export progress, but data playback will not be possible.
￭ If the export fails, check the current capacity and status to see if the hard disk is connected properly in the &quot;Device &gt; Storage device&quot; menu.
￭ If &lt;Hide&gt; is selected while the export is in progress, the screen changes to the upper menu, but the export continues.
●
●
●
Select a layout : Select a desired layout from the layout list.
Channel : Select a channel to export.
￭ You can select multiple channels. If you select &lt;All channels&gt;, all channels will be selected.
Export section : Set the &lt;Start&gt; and &lt;End&gt; time to run the export select to.
– Start : You can set the start time for the export to the desired time.
Click &lt;Start&gt; to set the export start time to the first time the video was recorded.
– End : You can set the end time for the export to the desired time.
Click &lt;End&gt; to set the export end time to the last time the video was recorded.
●
Overlap : Shows a list of overlapping data on a same time according to the number of data.
This is displayed when there are duplicate data in the same channel due to changes in the time or time zone.
●
Device : Select a device to export the among the searched devices.
●
Format : If you click &lt;Format&gt;, the format confirmation window will appear. Click &lt;Yes&gt; to format the selected
storage device.
●
File type : Select the export format.
￭ For more details, refer to the &quot;Setup &gt; Setting the System &gt; Date/Time/Language&quot; page in the Table of Contents.
– SEC : You can export in your own file format that can be played directly on your PC. You can play with the viewer
included in the export folder.
￭ If you select SEC format, you can choose whether to include &quot;PW Setup&quot; and &quot;Include text data&quot;.
– Recorder : You can export to a file that can be played only on the recorder.
– AVI : You can export to an AVI format-compatible with popular media players.
●
Path : Displays the folder location where the export file will be saved. You cannot change the storage folder, only
the file name to be saved.
●
Check capacity : You can check the selected export capacity and the current and remaining capacity of the export
device.
English _35
• live
￭ Exporting will not be able to start when a USB with insufficient free space is inserted.
search
You can search recorded video by various conditions such as time, event, and export.
Time Search
Screen Layout of the Search
You can search the recorded data by the desired date and time conditions.
￭ The time displayed will be based on the time zone and daylight saving time (DST) applied time zone, so it may be displayed differently depending on
whether the data time zone recorded at the same time and daylight saving time (DST) is applied.
1. Select &lt;Time search&gt; in the &lt;Search&gt; menu.
2. Select a channel to search.
3. Choose a layout.
Item
Description
Menu
Click each menu to go to the corresponding menu screen.
Search menu tab
Click the menu tab to display the detailed search menu. Click Search menu to go to the corresponding Search screen.
Search conditions
You can set various search conditions, such as date/time/event.
Search results
Displays search results.
4. Click , in the date selection window to select the year and month to search.
Dates with data will be shown in orange and current dates will be shown in orange circles.
5. Select a date to search from the calendar.
The first video of the searched data of the day will be displayed in the video window and the data will be displayed
in the time line.
●
Click &lt;Today&gt; to search for today's date. Today’s date will be selected.
●
If you click &lt;Overlapped&gt;, you can check the time line by setting the overlapping section by time change.
●
Export
/
Exports search results to a file.
Displays the search results as a list or thumbnail.
￭ Click &lt;Reset&gt; to initialize the search conditions and results.
￭ Double click on the desired item in the search results list to go to the play screen.
When you click Playback ( ), the video will be played in an instant viewer.
￭ You can specify a bookmark by clicking the bookmark ( ) in the search results list. You can check the specified video in the bookmark search menu.
￭ If the search results are in multiple pages , you can click to go to the previous/next page. Or, you can click the current page number and enter the
desired page to move.
36_ search
The displayed color differs depending on the type of recording data.
– Light green : Normal recording video
– Red : Event recording video
6. Double click the time of the desired channel to play the recorded video of that time.
Text Search
You can search for various events by channel.
You can search the data input to the POS device connected to the recorder.
1. Select &lt;Event search&gt; in the &lt;Search&gt; menu.
1. Select &lt;Text search&gt; in the &lt;Search&gt; menu.
2. Select a channel to search.
2. Select a date and time to search.
• search
Event Search
￭ If you select a channel to search, you can change the channel display mode by clicking &lt;
&gt;. You can select a desired channel by clicking or dragging it
from the channel table, and clicking the channel in the channel list.
3. Select a date and time to search.
￭ The search runs only for a maximum of 1 minute, so if the event search section is long, events may not be searched. In this case, reset the section and search
again.
4. Please select an event type. When you click the item, the event type selection window will appear.
￭ Event type options : Motion detection, IVA, Face detection, Auto tracking, Tampering detection, Defocusing detection, Fog detection, Audio detection,
Sound classification, Alarm input(camera), Continuous recording, Manual recording, ObjectDetection.Person, ObjectDetection.Face, ObjectDetection.Vehicle,
ObjectDetection.LicensePlate, Mask detection, ShockDetection
￭ Event type options may vary depending on the camera model.
5. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
6. Click the &lt;Search&gt; button.
The search results list will be displayed.
￭ To stop the search, click &lt;Stop&gt; in the search pop-up window. You can check the search results up until now.
●
CH : Displays the channel where the event occurred.
●
Camera name : Displays the camera name.
●
Event : Displays the event type of the recorded video.
●
Time : Displays the start time and end time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
3. Set the keyword item. When you click an item, the keyword setting window appears.
￭ You can search with a narrower range by entering specific characters.
●
Text search keyword : Enter the text to search.
●
Match case sensitivity : When checked, the entered characters will be searched with case-sensitivity.
●
Match whole words : When checked, only data that exactly matches the entered character will be searched.
●
Event keywords : You can search for text with preset event keywords. For more information about event keyword
settings, refer to the &quot;Setup &gt; Setting the Device &gt; Text &gt; Text Event Settings&quot; page in the Table of Contents.
4. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
5. Click the &lt;Search&gt; button.
The search results list will be displayed.
￭ To stop the search, click &lt;Stop&gt; in the search pop-up window. You can check the search results up until now.
●
Device : Displays the name of the POS device connected to the recorder.
●
CH : Displays the channel where the event occurred.
●
Keyword : Displays the searched text.
●
Time : Displays the start time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
6. If you double-click an item to play in the search list, the recorded video will be played.
7. If you double-click an item to play in the search list, the recorded video will be played.
English _37
search
Export Search
ARB Search
You can search the exported data on the connected storage device. Only data saved in recorder file format when
exported will be retrieved.
You can search auto-recovery backup data stored on ARB storage devices.
1. Select &lt;ARB search&gt; in the &lt;Search&gt; menu.
1. Select &lt;Export search&gt; in the &lt;Search&gt; menu.
2. When you click &lt;Select storage device&gt;, the device search window is displayed. Click &lt;
device.
3. Click &lt;Search&gt;.
Exported file information will be displayed.
&gt; to search for storage
￭ For more information about ARB search, refer to the &quot;Setup &gt; Setting the Device &gt; Storage device&quot; page in the Table of Contents.
2. When you click &lt;Select storage device&gt;, the device search window is displayed. Click &lt;
device.
The model name of the ARB storage device will be displayed.
3. Click &lt;Search&gt;.
The ARB file information stored on the device will be displayed.
●
Folder : Displays the folder where files are stored.
●
Name : Displays the saved file name.
●
Folder : Displays the folder where ARB data is stored.
●
CH : Displays the channel of the recorded video.
●
Name : Displays the file name stored on the ARB device.
●
Time : Displays the start time and end time of the exported video.
●
CH : Displays the recorded channel.
●
Playback : Plays the exported video with an instant viewer.
●
Time : Displays the start time and end time of the backed up video recording.
●
Playback : Plays the recorded video with an instant viewer.
4. If you double-click an item to play in the search list, the recorded video will be played.
4. If you double-click an item to play in the search list, the recorded video will be played.
38_ search
&gt; to search for storage
Bookmark Search
Smart Search
You can search for bookmarked data.
You can search for events by selecting a region of interest, an exclusive region, or a virtual line from a recorded video at
a specific time.
￭ To use smart search, you need to set the area of the camera's “Motion Detection&quot; or “IVA” to the entire area. However, if you want to search for cameras
1. Click &lt;
&gt; on the video window menu.
2. Set the smart search area in the video window.
1. Select &lt;Bookmark search&gt; in the &lt;Search&gt; menu.
￭ To search for bookmarks, you need to specify them by clicking the bookmark ( ) in the instant viewer or search results. If no bookmark is specified, search
results will not be displayed.
2. Select a channel to search.
￭ If you select a channel to search, you can change the channel display mode by clicking &lt;
&gt;. You can select a desired channel by clicking or dragging it
from the channel table, and clicking the channel in the channel list.
3. Select a date and time to search.
●
4. Click &lt;Search&gt;.
The search results list will be displayed.
●
Bookmark name : Displays the bookmark name you set.
●
Event : Displays the event type of the recorded video.
●
CH : Displays the recorded channel.
●
Time : Displays the start time and end time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Displays whether bookmarks are specified.
– The virtual line can be set in one direction or both directions. If you select the option of the direction of the
virtual line on both sides, it will detect all objects passing in both directions on one virtual line.
●
Region of interest (
) : Uses the entire screen as a non-detection area and specifies a specific area as a motion
detection area. Drag the mouse over the image or take a vertex to set the detection area at the desired location.
– When you set a zone, an event/object option icon will be displayed at the bottom of the zone. Click the icon to
exclude the event/object from the search.
– Intrusion (
5. If you double-click an item to play in the search list, the recorded video will be played.
￭ Bookmarked images will be stored without being overwritten during repeated recording. However, when the automatic deletion is set, it will be deleted
according to the set period.
￭ When the bookmark is released, the video will not be saved. If necessary, before releasing the bookmark, export the video.
￭ Up to 100 bookmarks can be specified.
Virtual line (
) : Detects the passing of an object based on the virtual line and direction set on the image. Click
and drag the start and end points of the virtual line to the desired location with the mouse.
) : Detects and searches for moving objects within the area set by the user.
– Enter (
) : Searches by detecting movement from the outside to the inside of the area set by the user.
– Exiting (
) : Searches by detecting the movement from the inside to the outside of the area set by the user.
– Person (
) : Searches for events that include people within the area set by the user.
– Vehicle (
) : Searches for events that include vehicles within the area set by the user.
– All Objects (
●
) : Searches for events that include all objects within the area set by the user.
Exclusive region (
) : Uses the entire screen as a detection area and specifies a non-detection area to exclude
detection of a specific area.
Drag the mouse over the image or take a vertex to specify the non-detection area at the desired location.
3. Set the date and time range to perform the virtual area search and click &lt;
&gt;.
4. When you click an item to play on the time line, the corresponding recorded video will be played.
￭ You can set up to 3 areas of interest, exclusion and virtual line.
￭ Click Delete ( ) to delete all the set areas.
English _39
• search
after Wisenet X series, you must select “Enable&quot; in &quot;Event setup &gt; IVA” of the camera. For details, refer to the &quot;Setup &gt; Setting the Event &gt; Event
setup&quot; page in the Table of Contents.
AI search
If there is AI data recorded by the camera, you can search for images in various conditions such as people, faces, and
vehicles.
￭ This function is not supported in some models.
￭ For products that support the AI search function, refer to the &quot;Functions Supported by Model&quot; page.
Person Search
In the recorded data, you can search for a person by any condition you want, such as gender, top/bottom color.
Screen Layout of the AI Search
1. Select &lt;Person search&gt; in the &lt;AI search&gt; menu.
2. Select a channel to search.
￭ If you select a channel to search, you can change the channel display mode by clicking &lt;
&gt;. You can select a desired channel by clicking or dragging it
from the channel table, and clicking the channel in the channel list.
3. Select a date and time to search.
4. Select a detailed search option.
●
Item
Description
Menu
Click each menu to go to the corresponding menu screen.
Search menu tab
Click the menu tab to display the detailed search menu. Click Search menu to go to the corresponding Search screen.
Search conditions
You can set various search conditions, such as date/time/gender.
Search results
Displays search results.
Export
/
Exports search results to a file.
Displays the search results as a list or thumbnail.
￭ The search options you set will be saved, and click &lt;Reset&gt; to reset the search conditions.
￭ Double click on the desired item in the search results list to go to the play screen.
When you click Playback ( ), the video will be played in an instant viewer.
￭ You can specify a bookmark by clicking the bookmark ( ) in the search results list. You can check the specified video in the bookmark search menu.
40_ AI search
Person search options : Gender, Clothing-Top color, Clothing-Bottoms color, Bag
￭ Click the option to display the option selection window. Select the desired search option.
￭ If no details are set, all conditions will be selected and searched.
5. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
6. Click the &lt;Search&gt; button.
The search results list will be displayed.
￭ To stop the search, click &lt;Stop&gt; in the search pop-up window. You can check the search results up until now.
●
CH : Displays the recorded channel.
●
Camera name : Displays the camera name.
●
Attribute : Displays the recognized search result attributes.
●
Time : Displays the start time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
7. If you double-click an item to play in the search list, the recorded video will be played.
Vehicle Search
From the recorded data, you can search faces according to your desired conditions such as gender and age.
You can search the vehicle by setting the vehicle type and color conditions from the recorded data.
1. Select &lt;Face search&gt; in the &lt;AI search&gt; menu.
1. Select &lt;Vehicle search&gt; in the &lt;AI search&gt; menu.
2. Select a channel to search.
2. Select a channel to search.
• AI search
Face Search
￭ If you select a channel to search, you can change the channel display mode by clicking &lt;
&gt;. You can select a desired channel by clicking or dragging it
from the channel table, and clicking the channel in the channel list.
￭ If you select a channel to search, you can change the channel display mode by clicking &lt;
3. Select a date and time to search.
3. Select a date and time to search.
4. Select a detailed search option.
4. Select a detailed search option.
●
Face search options : Gender, Age, Glasses, Mask
￭ Click the option to display the option selection window. Select the desired search option.
￭ If no details are set, all conditions will be selected and searched.
&gt;. You can select a desired channel by clicking or dragging it
from the channel table, and clicking the channel in the channel list.
●
Vehicle search options : Type, Vehicle color
￭ Click the option to display the option selection window. Select the desired search option.
￭ If no details are set, all conditions will be selected and searched.
5. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
5. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
6. Click the &lt;Search&gt; button.
The search results list will be displayed.
6. Click the &lt;Search&gt; button.
The search results list will be displayed.
￭ To stop the search, click &lt;Stop&gt; in the search pop-up window. You can check the search results up until now.
●
CH : Displays the recorded channel.
●
●
￭ To stop the search, click &lt;Stop&gt; in the search pop-up window. You can check the search results up until now.
●
CH : Displays the recorded channel.
Camera name : Displays the camera name.
●
Camera name : Displays the camera name.
Attribute : Displays the recognized search result attributes.
●
Attribute : Displays the recognized search result attributes.
●
Time : Displays the start time of the recorded video.
●
Time : Displays the start time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
●
Bookmark : Specifies a bookmark to the recorded video.
7. If you double-click an item to play in the search list, the recorded video will be played.
7. If you double-click an item to play in the search list, the recorded video will be played.
English _41
AI search
LP Search
LPR Search
You can search for vehicle license plates from the recorded data.
You can search for the license plate number recognized in the recorded data.
￭ LPR search is only available on recorder models that support AI recognition.
1. Select &lt;LP search&gt; in the &lt;AI search&gt; menu.
2. Select a channel to search.
￭ If you select a channel to search, you can change the channel display mode by clicking &lt;
&gt;. You can select a desired channel by clicking or dragging it
from the channel table, and clicking the channel in the channel list.
3. Select a date and time to search.
4. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
5. Click the &lt;Search&gt; button.
The search results list will be displayed.
￭ To stop the search, click &lt;Stop&gt; in the search pop-up window. You can check the search results up until now.
●
CH : Displays the recorded channel.
●
Camera name : Displays the camera name.
●
Time : Displays the start time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
6. If you double-click an item to play in the search list, the recorded video will be played.
1. Select &lt;LPR search&gt; in the &lt;AI search&gt; menu.
2. Select a channel to search.
￭ If you select a channel to search, you can change the channel display mode by clicking &lt;
&gt;. You can select a desired channel by clicking or dragging it
from the channel table, and clicking the channel in the channel list.
3. Select a date and time to search.
4. Enter the license plate number to search.
￭ Click &lt; &gt; to see the search guide for license plate number.
￭ The option of license plate number entry field is only available on recorder models that support LPR search.
5. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
6. Click the &lt;Search&gt; button.
The search results list will be displayed.
￭ To stop the search, click &lt;Stop&gt; in the search pop-up window. You can check the search results up until now.
●
CH : Displays the recorded channel.
●
Camera name : Displays the camera name.
●
LPR : Shows the identified license plate number.
●
Time : Displays the start time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
7. If you double-click an item to play in the search list, the recorded video will be played.
42_ AI search
play
You can play the recorded data and export the video you want during playback.
Screen Layout of the Play
Item
Playback control
Time line
Move the playback position and display event data.
You can use the video control function.
Video control
Overlap
Export section
￭
￭
￭
￭
￭
￭
￭
: Runs a smart search by specifying an area in the video window.
: Saves the video screen as an image.
: Zooms in the selected area on the screen. It only runs on a single split screen.
: Displays the image rotated 90 degrees. (This function is not supported in some models.)
: Turns the sound on or off.
: Changes the video display ratio.
: Enters the setup mode for dewarping the fisheye camera.
It works only when the video resolution is 1:1. Some models do not support this function.
• play
Set the date/time.
Status
Description
You can control video playback.
Date/Time
Show/Hide Channel
Item
Description
You can change the number of channels displayed in the time line.
￭ Up to 4 channels of time line can be displayed.
You can check the live, recording, and network status.
Remove all tiles
Removes all screens from the video window.
Full aspect ratio
Change the video display ratio.
Full screen
Display the image enlarged to full screen.
Previous/
Next Channel
You can check the time line of the previous/next channel.
The list will be displayed according to the number of overlapped data in the same time zone.
It will appear when a video is overlapped in one channel due to time or time zone change at the selected time.
Turns the export section setting on or off. You can select a start time and end time for exporting.
Export
You can export the video of the channel you are playing.
Filter
You can filter the event items to see the time line.
Channel
The channel and camera name will be displayed.
English _43
play
Play Search Results
Time Line Adjustment
Play Button Name and Function
Paused state
You can move the playback position and zoom the time line in and out.
●
●
●
Click the desired play position in the time line.
The playback start position will be moved.
￭ Click the start point on the left side of the time line to move the playback position to the start point of the first video.
￭ Place your mouse over the time line to see the corresponding thumbnail of the recorded video.
Click the time line and use the mouse wheel to zoom in or out on the time scale.
It will change in the order of 24 hours-12 hours-6 hours-3 hours-1 hour-30 minutes-15 minutes-5 minutes-1
minutes.
￭ The time line magnification of the time line will be displayed at the top right of the time line.
To see the time line previous or next zooming in, zoom in and drag the time line left or right.
Open Time Line Channel
You can display the time line of multiple channels.
●
Playback state
You can click &lt;
&gt;, &lt;
channels as selected.
Item
Description
Previous event
Go to the previous event video.
Previous frame
Moves backward to the key frame (I-frame).
Playback
Play the video.
Next frame
Moves forward one frame or more.
Next event
Go to the next event video.
&gt; to display 1 to 4 channels in the time line. The time line will be displayed as many
●
Click &lt;
●
Place your mouse over the time line to see the corresponding thumbnail of the recorded video.
&gt; to move to the previous or next channel.
Speed
Select the video playback speed.
Speed : x1/8, x1/4, x1/2, x1, x2, x4, x8, x16, x32, x64, x128, x256
It is used for reverse playback.
Fast backward
Pause
Speed : -x1/8, -x1/4, -x1/2, -x1, -x2, -x4, -x8, -x16, -x32, -x64, -x128, -x256
￭ Depending on the split screen, the maximum speed may be limited.
Pause the video.
It is used for forward playback.
Fast forward
44_ play
Speed : x1/8, x1/4, x1/2, x1, x2, x4, x8, x16, x32, x64, x128, x256
￭ Depending on the split screen, the maximum speed may be limited.
Search Results Export
You can export the search results to a file.
1. Click the &lt;
&gt; button.
2. Select a layout and channel to export.
• play
3. Select a start date/time and an end date/time.
￭ If you changed the time zone of the recorder, select whether to apply DST.
4. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
5. Click &lt;
&gt; to select a storage device.
￭ If you click &lt;Format&gt;, the format confirmation window will appear. Click &lt;Yes&gt; to format the selected storage device.
6. Please select a storage file type.
– SEC : You can export in your own file format that can be played directly on your PC. You can play with the viewer
included in the export folder.
￭ Click &lt;Setup&gt; to set a password for the exported video.
￭ If you check &lt;Include text data&gt;, you can save text data in the exported video.
– Recorder : You can export to a file that can be played only on the recorder.
– AVI : You can export to an AVI format-compatible with popular media players.
7. Check the path to save the file to be exported. Only the file name to be saved can be changed.
8. Click &lt;Check capacity&gt; to check the storage capacity.
9. Click &lt;Start&gt;.
When the export is complete, a confirmation window will be displayed.
10. Click &lt;OK&gt; to exit.
￭ If you click &lt;Stop&gt; while exporting, the export action is canceled.
English _45
setup
Sets the camera, recording, event, device, network, and system environment.
Setting the Camera
Screen Layout of the Setup
You can access to the channel setup, camera settings, and profiles and camera password-related settings.
Setting the Channel
You can register a network camera for each channel and make connection between.
Setup &gt; Camera &gt; Channel setup
￭ When you register a camera for the first time in the &quot;Setup &gt; Camera &gt; Channel setup&quot; menu, the camera setup screen will be
displayed. For details, refer to the &quot;Getting Started &gt; Camera Setup&quot; page of the table of contents.
Item
Menu
Top menu list
Description
Click each menu to go to the menu screen.
Configure the settings or select a parent item to change the existing settings.
Sub-menu list
Among the sub-menus of selected parent menu, select a desired item to set.
Detailed Menu
Click desired item's input field to change and enter a desired value.
●
●
Apply the modified settings.
Revert
Revert to the settings used before the change.
￭ Camera searched with ONVIF does not provide previews.
Camera name : Provide a camera Name. You can enter up to 15 letters including spaces.
●
IP address : Display the IP address of a network camera.
●
Model : Show the camera model name.
●
Protocol : Show the protocol information of a registered network camera.
●
Apply
: Displays the camera of the corresponding channel as a list or a thumbnail.
Video
– On/Off : You can turn ON/OFF the selected channel's camera. If the camera video is turned off, a blank screen
is displayed.
– Covert1 : Shows information other than the video of the selected channel.
For privacy protection, it does not display the video while the recording continues.
– Covert2 : Shows nothing but an empty screen while the recording continues.
￭ If the channel is set to &lt;Covert1&gt; or &lt;Covert2&gt; mode, the channel's sound is not hearable.
However, the channel's sound is recorded if its Audio setting is set to &lt;On&gt;, even the sound is not heard in Live mode.
46_ setup
●
Audio
Automatic Registration of Network Cameras
– If set to &lt;On&gt;, you can turn the audio of the channel ON/OFF on the Live screen.
– If set to &lt;Off&gt;, the channel's audio is off on the Live screen and not recorded.
Status : Display the connection status.
●
Edit : You can change the connection information of the camera.
●
Upgrade : You can check the camera’s version, upgrade version, and status and upgrade it.
●
PoE output status : For products that support PoE, this shows the current status of the connected PoE.
For products that support PoE, refer to the &quot;Functions Supported by Model&quot; page.
• setup
●
￭ If you cannot register a camera after initializing the system, check the network setting. As the system is initialized and the network setting
is reset, the camera's network bandwidth will be different from the product's network bandwidth, so it will be impossible to register a
camera.
1. In the &lt;Channel setup&gt; field, click on the &lt;Auto detect&gt; button.
2. &lt;Auto detect&gt; window appears.
￭ Click &lt;
&gt; in the camera list on the live screen to automatically search and register the camera.
3. Select a camera to register in the &lt;Searched camera&gt; list and press the &lt;Register&gt; button.
You can check the selected camera in the &lt;Camera to register&gt; list.
￭ An already registered camera will be marked in blue in the list.
￭ If you search for the camera again or if the IP is an old IP that was not assigned by the DHCP server (such as 192.168.1.100), then press the
&lt;Refresh&gt; button to check if a new IP has been assigned.
￭ &lt;Status&gt; shows the camera authentication status. In the &lt;Auth failed&gt; state, click &lt;
￭ Click a header at the top of the list to sort the list according to that header.
&gt; to enter the camera ID and password.
4. To change the IP address of the camera, select the desired camera from the &lt;Camera to register&gt; list and
press the &lt;Change IP&gt; button.
5. Click &lt;Next&gt; at the bottom of the screen to set the registered camera channel.
6. Press the &lt;Register&gt; button on the lower right of the screen to register the selected camera.
￭ If you register a camera using a user account—not admin account—the camera features may be limited.
￭ When you change the camera ID/password in the camera web viewer, if the camera is already registered in Recorder, you also have to
change the camera ID/password information registered in Recorder.
￭ When the camera is factory reset, it defaults to the ID and password set in &quot;Setup &gt; Camera &gt; Camera password&quot;.
￭ If the camera's ID and password have already been set, the registered information matches the ID and password set in the &quot;Setup &gt;
Camera &gt; Camera password&quot;. (up to 3 sets)
￭ Wisenet camera is registered via Wisenet protocol while a third party camera is registered via ONVIF protocol.
￭ A device running a DHCP server should never be connected to a PoE port or a camera setup port. (e.g. router)
￭ If your camera uses its own power supply unit, you need to manually register or auto-register the camera.
￭ For products that support PoE, refer to the &quot;Functions Supported by Model&quot; page.
English _47
setup
Registering a Network Camera Manually
●
Address type : Select an address type of the camera.
￭ The supported address type may differ depending on the type of the connected product.
– IPv4/IPv6 : Used to provide the IP address of the camera manually.
– Wisenet DDNS : This is available only if the camera is registered with the Wisenet DDNS(ddns.
hanwhasecurity.com) server. Provide the registered domain for DDNS ID.
Example) http ://ddns.hanwha-security.com/snb5000 ; provide &quot;snb5000&quot; for Wisenet DDNS
– URL : Used for URL address input.
￭ The DDNS specs supported by each camera can be checked in the user manual of the corresponding camera.
●
IP address : Provide the IP address of the camera.
●
Port : Provide the device port of the camera.
●
1. In the &lt;Channel setup&gt; field, click on the &lt;Manual&gt; button.
2. &lt;Manual registration&gt; window appears.
￭ You can register the camera manually by clicking &lt;+&gt; from the camera list on the live screen.
3. Select a channel and protocol used to connect to a camera.
The input items may differ depending on the selected protocol.
●
Wisenet : Wisenet camera's protocol can be used.
●
ONVIF : Means the camera supports ONVIF protocols. When connecting a camera that its name cannot be
found from the list, select &lt;ONVIF&gt;.
TLS : You can set whether to use TLS.
●
ID : Provide the ID of the camera that you want to register.
●
Password : Enter the password of the camera to be registered.
●
Details : You can set the streaming mode.
5. Select &lt;ONVIF&gt; or &lt;RTSP&gt; for the protocol and enter your input for each field appears.
●
– IP address : Enter the camera's IP address.
– ONVIF port : Enter the port number when the address type is IPv4 or IPv6.
– TLS : You can set whether to use TLS.
– Channel : Enter the channel to register the camera.
RTSP : Comply with RFC 2326, one of &quot;Real Time Streaming Protocol (RTSP)&quot; for real-time streaming.
– ID : Enter the camera ID.
4. If you select the &lt;Wisenet&gt; protocol, check options as necessary.
– Password : Enter the camera password.
Model : Select a camera model.
– Unknown : Select when the camera model cannot be identified.
– Wisenet Camera : You can register Hanwha Techwin's cameras and encoders.
– Wisenet Multi-Channel : You can register Hanwha Techwin's multi directional cameras and multi-imager
cameras. A multi-channel camera is a camera that has multiple camera modules in one body. Autoregistering your camera to Recorder lets you register multiple channels at once. However, if you want to
manually register it, you need to register one channel at a time.
–
ONVIF : After selecting an IP type, set IP address, ONVIF port, ID, password, and details.
– IP type : Select the IP type of the camera.
won’t be able to register it. In this case, synchronize the camera and recorder time.
●
HTTP : Provide the HTTP port of the camera.
●
￭ When a camera is registered with ONVIF, if the difference in system time between the camera and recorder is 2 minutes or more, you
●
￭ Depending on the camera type, some device ports will not be supported.
– Details : You can configure the authentication mode and streaming mode.
●
RTSP : Set URL, ID, password, and details.
– URL : Enter your RTSP access address. For more information, see your camera user manual.
– ID : Enter the camera ID.
– Password : Enter the camera password.
– Details : You can set the streaming mode.
￭ If ONVIF or RTSP protocol is selected, you can set the streaming mode in the Details section.
–– TCP : The connection to network camera operates in the RTP over TCP mode.
–– UDP : The connection to network camera operates in the RTP over UDP mode.
–– HTTP : The connection to network camera operates in the RTP over TCP (HTTP) mode.
–– HTTPS : The connection to network camera operates in the RTP over TCP (HTTPS) mode.
48_ setup
If you want to check the error details of camera registration
Network Camera Firmware Upgrade
If you failed to register a camera, the reason for the failure will be displayed.
Connection failed due to unknown error. : This message appears if the camera has failed to be registered
due to unknown connection status.
●
Due to the camera account locking, access has failed. : When you enter a wrong ID/password 5 times to
login to the camera account, this message is displayed.
Try to log in again after 30 seconds. If the same message appears, you may need to check whether someone
has tried to access your camera account from the outside.
●
Connected successfully. : This message appears if the camera is connected successfully.
●
Incorrect model information. Provide the correct model information. : This message appears if the model
information provided for registering the camera is incorrect.
●
Authentication has failed. : This message appears if the ID or password provided for registering the camera is
incorrect.
●
Connection has failed due to excessive concurrent users. : This message appears if the concurrent user
count exceeds the upper limit.
●
Connection has failed due to incorrect HTTP port information. : This message appears if the HTTP port
number of the camera is invalid.
●
●
Connection has failed. Unknown connection status. : This message appears if the camera has failed to be
connected due to a unknown error.
User Model Modification : When registering a new camera, it is named according to the device's default if
user set the model to &lt;Wisenet Camera&gt;. In case if automatic registration fails, user can change the model
name of camera to be registered.
To edit camera profile
To change profile, refer to the “Setup &gt; Setting the Camera &gt; Setting the Profiles&quot; page in the Table of
Contents.
￭ In case of Recorder, if you set 3 different profiles for live, recording and network profile, one camera will produce video streams accordingly,
having different stream formats. Especially, note that the live profile may vary depending on the used screen split mode.
￭ For cameras, if applied with one profile only, the produced frame rate is fixed as the profile specifies; if applied with multiple profiles,
produced video stream's frame rate is not guaranteed. For example, if applied with 2 profiles of 30fps, the camera may transmit streams at
20fps.
• setup
●
●
Channel : Displays channel information.
●
Model : Displays the camera model information.
●
Current version : Displays the current camera firmware version.
●
Upgrade version : Displays the firmware version to upgrade.
– Press the &lt;
– &lt;
●
&gt; button to select the firmware manually within the USB.
&gt; indicates an upgrade via a remote server.
Status : Displays the status of the ongoing upgrade (upgrading, successful, failed).
1. Press the &lt;Upgrade&gt; button in the &lt;Channel setup&gt; field.
2. Displays the upgradeable channel list among the connected cameras.
￭ If newer firmware exists on the remote server, the upgrade version is displayed, and the check box is automatically selected.
&gt; button to get the upgrade version information from the server.
￭ If you do not see the upgrade version, you can press the &lt;
￭ Connect a USB camera with camera firmware to the recorder and press the &lt; &gt; button to check and select the firmware file in the USB.
￭ Select a channel and press the &lt;Apply to other channels&gt; button to apply the firmware to other channels connected to the same model at once.
3. Check the box of the channel you want to upgrade.
Delete Network Camera
1. Click &lt;Delete&gt; in the &lt;Channel setup&gt; field.
2. When the delete window appears, select the camera channel to delete.
￭ Click &lt;All channels&gt; to select cameras for all channels.
3. Click &lt;OK&gt; to delete the camera of the selected channel.
4. Click the &lt;Upgrade&gt; button. The camera firmware upgrade starts.
￭ You can move to another menu while upgrading.
￭ You can stop the upgrade by clicking the &lt;Stop&gt; button during the upgrade.
￭ When the upgrade is completed, you can see the result in the popup window.
￭ Firmware upgrade is available only for channels connected with the Wisenet protocol and the camera’s administrator account.
￭ If the upgrade version is not displayed even though the camera’s firmware is out of date, check the network settings.
￭ If there are more than 50 firmware files in the top USB folder, the file may not be scanned.
￭ The system may reboot if USB is disconnected from the recorder during an upgrade via USB.
￭ Video data of the channel connected to the camera to upgrade may not be recorded.
￭ Do not format the HDD until the upgrade is complete. The upgrade may fail.
English _49
setup
Setting the Camera Functions
You can set the camera while viewing the live video of the selected camera.
Setup &gt; Camera &gt; Camera setup
●
SSNR : Adjusts the brightness by reducing noise and minimizing afterimages even in dark places.
●
Sens-up : Automatically adjusts the shutter speed according to the brightness of the current light.
●
IRIS/Lens : Adjusts the brightness by automatically or manually adjusting the camera IRIS and lens.
●
AGC : Adjust the brightness by amplifying the camera's electrical signal when images are shot in the dark.
Day/Night
You can change the mode to adjust the color and contrast.
You can set Mode, Dwell time, Negative color, Duration, Alarm input, Switching brightness, Simple focus after
Day/Night, and Activation time (color).
●
You can select the day/night video display mode in &lt;Mode&gt;.
– Color : Images are always displayed in color.
– B/W : Images are always displayed in B/W
– Auto : The video will be displayed in color in normal environments and in B/W at night.
– External : Displays a color or B/W video by linking an external infrared camera to the alarm in terminal. Set
the alarm in item when selecting the &lt;External&gt;.
￭ You can use this feature in the following cases :
1. A camera connected to Wisenet protocols.
2. A camera connected with admin privileges.
￭ For more details on camera settings, refer to the camera user manual.
Settings and operational spec vary depending on each camera.
￭ This function is not supported in some models.
SSDR
– Schedule : Controls the video output mode by directly inputting the color video activation time. Click
&lt;Setup&gt; and enter the activation time.
Special
You can set DIS (Digital Image Stabilization), Defog, and Defog level.
Focus
You can adjust the focus of you camera's video.
You can set Focus, Zoom, Simple focus, and Initialize focus.
If there is a significant difference between the dark and the bright areas, increase the brightness of the dark areas
to maintain the level of brightness of the entire area.
You can set Mode, Level, and D-Range.
Video rotation
Backlight
You can set an area to be hidden in the camera image range to protect privacy. You can select whether or not to
use the privacy setting and set up to 32 new privacy areas.
You can view both bright and dark areas.
You can set Mode, WDR level, WDR black level, and WDR white level.
Exposure
You can adjust the exposure of your camera.
You can set brightness, shutter, SSNR, Sens-up, iris/lens, and AGC.
●
Brightness : Adjusts the brightness by setting the exposure value.
●
Shutter : Adjusts the brightness by controlling the camera shutter speed. If you select shutter, you can set
among the items below.
– Auto : Adjusts the brightness automatically, controlling the shutter speed of the camera.
– ESC (Electronic Shutter Control) : Adjusts the brightness automatically, controlling the shutter speed
according to the surrounding brightness.
– Manual : Adjust the brightness by manually selecting the maximum/minimum shutter speed of the camera.
– Anti-flicker : Reduces flickering in video when screen blur occurs due to different lighting and frequency of
attention. The shutter speed cannot be set when the anti-flicker frequency is selected.
50_ setup
You can set flip/mirror modes and hallway view.
Privacy area
￭ With a PTZ camera, it is not possible to configure settings, and when it is permitted, the setting area may be incorrect.
Setting the Profiles
Setting the Live Profile
You can change the live transfer settings of the network camera.
Setting the Recording Profile
Setup &gt; Camera &gt; Profile setup &gt; Live
You can configure the video profile settings for instructing the network camera (connected to each channel) to
make recording.
• setup
Setup &gt; Camera &gt; Profile setup &gt; Record
●
￭ You can configure the settings only for the profiles that are supported by the camera.
￭ If the profiles used for recording and network are different, camera's video feed may not comply with the frame rate as specified in the
●
Camera name : Display the camera name.
●
IP address : Display the IP address of a camera.
●
Live replacement : You can select the live profile setup mode.
If you select &lt;Manual&gt; the profile setup items are enabled, and you can change settings manually.
– Auto : For the profile for live monitoring, a profile optimized for each split mode is displayed, along with the
‘Live4NVR' profile automatically generated at the time of the camera registration.
camera.
￭ It is recommended to set the identical codec for the Record/Live/Remote profile when setting the camera profile.
●
: Displays the camera of the corresponding channel as a list or a thumbnail.
– Manual : Live monitoring is performed with the profile selected by the user from the registered camera
profiles.
: Displays the camera of the corresponding channel as a list or a thumbnail.
●
Camera name : Display the camera name.
●
IP address : Display the IP address of a camera.
●
Profile : You can set the camera profile.
●
Profile : You can select the recording profile for selected channel.
●
Codec : Show the codec of the selected profile.
●
Codec : You can check the codec for selected channel.
●
Resolution : Show the resolution of the selected profile.
●
Resolution : You can select the resolution for selected channel.
●
Frame rate : Show the frame rate of the selected profile.
●
Frame rate : You can set the frame rate for selected recording profile.
●
Edit : You can add, change, and delete the camera profiles.
●
Edit : You can add, change, and delete the camera profiles.
– Record : Live monitoring is performed with the profile set for recording.
English _51
setup
Setting the Remote Profile
Editing the Profiles
You can set the video profile transmitted to the network.
You can change the video settings of a registered network camera for each channel.
Setup &gt; Camera &gt; Profile setup &gt; Remote
Setup &gt; Camera &gt; Profile setup
: Displays the camera of the corresponding channel as a list or a thumbnail.
●
●
Camera name : Display the camera name.
●
IP address : Display the IP address of a camera.
●
Profile : Select a network profile for the connected camera.
●
Codec : Show the codec information for the selected network profile.
●
Resolution : Display the resolution for the selected network profile.
●
Frame rate : Shows the selected network profile's frame rates.
●
Edit : You can add, change, and delete the camera profiles.
￭ If the profiles used for network and recording are different, camera's video feed may not comply with the frame rate as specified in the
camera.
●
Channel selection : You can select camera channels to change their video transmission settings.
●
Add : You can add camera profile. Click on the &lt;Add&gt; button to launch the addition window.
Enter the information and click on the &lt;OK&gt; button to add it to the list.
●
Delete : You can delete the selected profile from the list.
●
Apply to other channels : If you select &lt;Apply to other channels&gt;, “Apply to other channels” confirmation
window will appear.
After selecting channels that the settings will be applied to, click on &lt;OK&gt; to apply them to the selected
channels.
●
Profile : You can check the video profile of the camera connected in the camera setup.
●
Codec : You can check the codec for the selected channel.
●
Resolution : You can change the resolution of the selected channel.
●
Frame rate : You can change the frame rate of the selected channel.
●
Bitrate control : You can change the bitrate of the selected channel.
●
Type : Displays the currently applied profile.
￭ If you change specific profile settings for each product, the frame rate's setup range may be changed.
Example) If you set the frame rate for the first profile to 30 fps, then the setting range for the second profile may be changed to 15 fps.
￭ Any settings other than codec, resolution, and frame rates can be changed in the setup menu of the camera web viewer. For camera web
viewer, refer to the &quot;Setup Viewer &gt; Setting the Camera &gt; Camera Setup&quot; page in the Table of Contents. Click &lt;Camera webviewer&gt;
button for connection.
￭ If you change the current profile settings, you may encounter an interrupted playback on the recording or live screen for a certain time.
￭ Changes made in your camera’s setup page will be applied immediately. But any changes made through the camera's online website, it
may take up to 3 minutes to apply the changes.
￭ Bitrate settings are not supported for ONVIF cameras.
52_ setup
Dewarping Setup
How to set WiseStream
Press the &lt;Dewarping&gt; button at the bottom of the &lt;Detailed profile configuration&gt; window to go to the
distortion correction setup popup window for each channel.
Function to analyze the complexity of the video and effectively reduce the data size while maintaining the
quality. For details, refer to the camera's help or the product's user guide.
Press the &lt;WiseStream&gt; button at the bottom of the &lt;Detailed profile configuration&gt; screen to go to the
WiseStream setup popup window for the channel.
• setup
●
●
Profile : Displays the profile type.
Video output / Dewarp view: You can set &lt;Video output&gt; and &lt;Dewarp view&gt; for each profile type.
– Fisheye view : If you select &lt;Fisheye view&gt; from &lt;Video output&gt;, the &lt;Fisheye view&gt; is automatically
selected for &lt;Dewarp view&gt;.
– Dewarp view : If you select &lt;Dewarp view&gt; from &lt;Video output&gt;, you can set &lt;Quad view&gt;,
&lt;Panorama&gt;, or &lt;Quad view 1 - 4&gt; for &lt;Dewarp view&gt;.
￭ You can select view modes supported by your camera.
●
Resolution : You can set the resolution of the profile.
●
Mounting mode : You can change the fisheye installation type. You can select a view mode from among
ceiling/ground/wall depending on the installation location.
●
Mode : You can choose the degree of video compression. You can choose &lt;Off&gt;, &lt;Low&gt;, &lt;Medium&gt;, or
&lt;High&gt;.
￭ WiseStream setup cannot be executed if there is no camera registered in Recorder that supports WiseStream.
￭ If there is no camera registered in the Recorder that supports fisheye view, Dewarping Setup will not be available.
English _53
setup
Dynamic GOV/FPS setup
Setting Camera Password
Dynamic GOV can be used to automatically change the length of GOV depending on the video condition. For
details, refer to the camera's help or the product's user guide.
You can change the passwords of all registered cameras at once.
At the bottom of the &lt;Detailed profile configuration&gt; screen, press the &lt;Dynamic GOV &amp; FPS&gt; button to
open the dynamic GOV/FPS setup popup for the channel.
●
Profile : Shows the video profile of the connected camera setting.
●
Dynamic FPS : Automatically adjusts the frame rate (frames per second) based on the video conditions.
●
You can register the camera’s ID and password.
Setup &gt; Camera &gt; Camera password
●
Password : Enter the new password for the factory default camera according to the password setting rules.
The initial password for the camera must be entered.
Dynamic GOV
●
Confirm password : Input the new password again.
– Mode : Set the GOV length to change automatically.
●
ID : Enter the ID of the camera whose ID and password are set.
– Length : Enter the maximum GOV length value to be applied when there is no motion in the video.
Minimum GOV value can be set on the camera web page.
●
Password : Enter the password of the camera whose ID and password are set.
– Range : The range of the input value of &lt;Length&gt; is displayed.
￭ Any profile not supported with the dynamic GOV/FPS setting is marked with '-'.
￭ When the password is in factory reset, it can be changed and managed in a batch.
￭ If you click &lt; &gt;, a basic guide for password setup is displayed.
￭ If you select &lt;Show password&gt;, the current password is displayed as the actual input characters.
￭ If you check the &lt;Change the password of all registered cameras&gt;, the passwords of all cameras are changed with the entered
password.
￭ Up to 3 sets of camera ID with password and password can be registered.
You can use the registered camera ID/PW to automatically discover and register the camera from the &quot;Channel setup &gt; Auto detect&quot;
screen.
￭ A camera password registered with ONVIF and RTSP cannot be changed.
54_ setup
Setting the Recording
Record Setup
You can setup scheduled recording, event recording and other recording related settings.
You can set the resolution and number of recordings for each channel when an event occurs or during a normal
recording.
You can check frame rates and data transfer amount of Full Frame and Key Frame recordings for each channel,
and set the transfer limit for recordings.
Record Schedule
If you set a recording schedule for a specific date and time, the recording will start at that specific time.
• setup
Setup &gt; Record &gt; Record setup
Setup &gt; Record &gt; Record schedule
●
●
Channel : Select the channel you want to set.
●
All : The entire time range (Monday through Sunday including holidays, AM 0~ PM 23) will be reserved with the
same recording schedule.
●
Apply to other channels : If you select &lt;Apply to other channels&gt;, “Apply to other channels” confirmation
window will appear.
After selecting channels that the settings will be applied to, click on &lt;OK&gt; to apply them to the selected
channels.
￭ Event recording and scheduled recording starts about 3 seconds prior to the event/schedule for guaranteed recording.
●
Camera name : Display the camera name.
●
IP address : Display the IP address of a camera.
●
Continuous recording / Event recording : Set the recording method for Continuous recording or Event
recording.
– Full frame : Records all frames fed by the camera.
– I-frame : Records only key frames fed by the camera. It depends on the camera's settings.
Function
Description
)
No recording
No schedule / event recording
Green (
)
Continuous
Scheduled recording only
Event
Event recording only
Continuous/Event
Both scheduled / event recordings
Orange (
●
– Off : No recording is made.
White (
Red (
)
)
: Displays the camera of the corresponding channel as a list or a thumbnail.
●
Record setting by the color
Color
Apply to other channels : If you select &lt;Apply to other channels&gt;, “Apply to other channels” confirmation
window will appear.
After selecting channels that the settings will be applied to, click on &lt; OK&gt; to apply them to the selected
channels.
Each press of a selected cell will cycle through &lt;No recording&gt;-&lt;Continuous&gt;-&lt;Event&gt;-&lt;Continuous/
Event&gt;.
●
Frame
– Full frame : Shows the amount of data for all the scene recordings.
– I-frame : Shows the amount of data for the main scene recordings.
●
Limit : Set the amount of data allowed for input for each channel.
●
Event : When an event occurs, you can set which point you will start or stop recording.
– Pre : When an event occurs, recording will be started regardless of the time set.
If you set it to five seconds, recording will start at five seconds before an event occurs.
– Post : When an event occurs, recording will continue after the time set.
If you set it to five seconds, recording will continue for a further five seconds after an event is finished.
●
Audio : Specify whether to record the sound received from the camera or not.
English _55
setup
￭ If a channel's data transfer exceeds defined allowed limit, then it may affect to other channels, and may force switching to &lt;I-frame&gt;
recording even when the channel is configured to &lt;Full frame&gt; recording mode. For Key Frame recording channels, the icon for limited
recording appears on the live screen's top side.
But if the sum of the limits is below the max limit, you can still receive the entire frames despite exceeding the permitted bitrates for each
channel.
￭ A channel displayed in yellow indicates that the recorded data is not being transferred from the camera and that the recording is being
performed temporarily using another profile on the camera.
Check the channel information to see the applied profile to the channel listed in yellow.
A channel displayed in orange indicates that the amount of inputted data is greater than the permitted data amount. In this case, it is
impossible to record all of the incoming frames. Instead, only part of the frames (1 or 2 frames per second) can be recorded.
To resolve this issue, you must set the permitted data amount to be greater than the amount of inputted data.
Refer to the &quot;Live &gt; Live screen mode &gt; Check the camera status&quot; page in the Table of Contents.
Setting the Event
You can set the event-related settings such as whether or not an event is detected for each channel and whether an
alarm occurs.
AI function setup guide
To use AI function, set any of the following options as necessary : See the relevant page for detailed setup method.
–– Setup &gt; Event &gt; AI engine
–– Setup &gt; Event &gt; Event setup &gt; Object
–– Setup &gt; Event &gt; Event setup &gt; AI recognition
–– Setup &gt; Event &gt; Event setup &gt; Mask
–– Setup &gt; Event &gt; Event setup &gt; IVA
Record Options
–– Setup &gt; Event &gt; Event rule setup
You can set recording options, such as enabling dual recording or overwrite of hard disk for repeated recording.
Setup &gt; Record &gt; Record options
￭ AI recognition function may have different settings and operation specifications depending on the recorder model and camera.
AI Engine
You can set whether to use AI events (object detection, AI recognition) from the camera, and check the usage of
AI engine.
Setup &gt; Event &gt; AI engine
●
●
Enable dual recording : Select this if you want to record both the recording profile and remote profile at the
same time. Enabling dual recording is applied with a profile suitable for split mode during playback.
Overwrite : Select the recording method when the hard disk storage capacity is full.
– Checked (
) : If the HDD is full, this will overwrite the existing data and keep recording.
– Not checked (
●
●
●
) : If the HDD is full, this will stop recording automatically.
Beeps when recording is stopped: If &lt;Overwrite&gt; has not been set, this button is enabled. Specifies whether
to use beep or not when HDD recording ends.
If you check it, the beep will sound on the disk full and the recording stops.
Retention period : If you check this option, the period list box is active, and you can set the automatic deletion
period. Specify the deletion period to delete any earlier data than the specified date. However, you can search
for data from the current time to the selected date.
￭ If &lt;Overwrite&gt; has been set, this button is enabled.
￭ You can select a channel and set a different recording duration for each channel.
Apply to other channels : If you select &lt;Apply to other channels&gt;, “Apply to other channels” confirmation
window will appear. After selecting channels that the settings will be applied to, click on &lt;OK&gt; to apply them
to the selected channels.
￭ If you press &lt;Retention period&gt; when you have completed your settings, all the existing data earlier than the specified period will be
deleted automatically. If you need to keep your old data, export it first.
56_ setup
●
AI engine status : Shows the AI engine usage status.
●
Camera name : Display the camera name.
●
IP address : Display the IP address of a camera.
●
Type : Displays the camera type.
●
Object detection : Sets whether or not to enable object detection for the camera.
●
AI recognition : Sets whether or not to enable AI recognition function for the camera.
●
Usage : Shows the AI engine usage of the camera.
￭ If the AI engine capacity is full, no additional settings can be made. To set additional AI functions, disable the object detection and AI recognition
function from the previously set channel.
￭ AI recognition works only when the object detection option is set to &lt;Enable&gt;.
￭ The AI engine function is only available on products that support AI. For products that support the AI search function, refer to the
&quot;Functions Supported by Model&quot; page.
Event Setup
AI recognition
You can configure whether or not to detect events sent by the camera for each channel and configure detailed
settings.
Setup &gt; Event &gt; Event setup &gt; AI recognition
￭ AI recognition function is only available for recorder models that support AI engine function.
Setup &gt; Event &gt; Event setup
Object : You can set detailed settings for object detection of the connected camera.
●
AI recognition : Sets detailed settings for AI detection of the connected camera.
●
Mask : Sets detailed settings for mask detection of the connected camera.
●
Motion : You can set detailed motion detection for the connected camera.
●
IVA : You can set up intelligent video analytics of the connected camera.
●
Tampering : You can make detailed settings for tampering detection, such as when the screen of a connected
camera is obscured or the camera location is changed.
●
Video loss : You can configure the detailed settings for video loss detection on the connected camera.
• setup
●
￭ The settings for Object detection may vary depending on the recorder model or the connection of Wisenet AI camera.
Object
●
LPR : Sets whether or not to enable license plate number recognition.
￭ AI recognition function may have different settings and operation specifications depending on the recorder model and camera.
￭ Clicking &lt; &gt; at the top right of the screen shows the AI camera setup guide.
Setup &gt; Event &gt; Event setup &gt; Object
Mask
Setup &gt; Event &gt; Event setup &gt; Mask
￭ The settings for Mask detection may vary depending on the recorder model or the connection of Wisenet AI camera.
●
Object detection : You can set whether to enable object detection.
●
Object type : You can select the object type to detect.
●
●
●
●
￭ Object items may vary depending on the camera model.
BestShot : You can set the object to display the bestshot items.
￭ Set the same as the item selected in &lt;Object type&gt; to display the best shot when an event is detected.
Detection excluded area : You can set the exclusion area for AI object detection. Click &lt;Add&gt; to set the
detection exclusion area on the preview screen.
Sensitivity : Sets the object detection sensitivity.
￭ Setting the sensitivity level high increases the object detection rate but also raises the detection error rate.
Object size : You can set the size of the object to recognize the motion.
●
Mask detection : Sets whether or not to use mask detection.
●
Type : You can select the mask detection type.
●
Minimum duration : Sets the minimum observation duration upon mask detection.
– Click &lt;Setup&gt; to select the minimum/maximum size and set the object size on the preview screen.
￭ If detection errors occur frequently, set the detection excluded area or lower the object detection sensitivity.
English _57
setup
Motion
IVA
Setup &gt; Event &gt; Event setup &gt; Motion
Setup &gt; Event &gt; Event setup &gt; IVA
●
Motion detection : You can set whether to enable motion detection.
●
IVA : You can set whether to enable intelligent video analytics.
●
MD type : You can set a detection area and a detection excluded area.
●
Type : You can set a virtual line, virtual area, and detection excluded area.
– Detection area : Set the area to detect motion.
– Virtual line : Set the virtual line to enable intelligent video analytics.
– Detection excluded area : Set the area to not detect motion.
– Virtual area : Set the area to enable intelligent video analytics. You can set the details of virtual areas to fit
your purposes.
– Add : After selecting the desired area item, set the area on the preview screen.
￭ Intrusion : Creates an event when the motion of an object in the designated area is detected.
￭ Enter : Creates an event when a moving object enters into the target area from the outside.
￭ Exiting : Creates an event when a moving object goes out of the target area.
￭ Appear/Disappear : When an object which does not exist inside the area designated by the user appears inside the area without passing the
– Area initialization : You can clear all the set areas.
●
Object size : You can set the size of the object to recognize the motion.
●
Detection level : You can set the basic level required for motion detection. Level values can be set for each
detection area set in &lt;MD type&gt;. If a motion value is bigger than the set level, then a motion detection event
is triggered.
●
Detection result display : You can overlay the detection area over video.
●
Sensitivity : You can set the sensitivity of motion detection for each area. Set a lower sensitivity for an
environment where the background and an object are clearly distinguishable and a higher sensitivity for an
environment where the background and an object are not clearly distinguishable.
– Detection excluded area : Set the area to not enable video analytics in the virtual line and the virtual area.
●
Activation time : You can set the activation time for motion detection.
– Area initialization : You can clear all the set areas.
– Click &lt;Setup&gt; to select the minimum/maximum size and set the object size on the preview screen.
area line and remains for a certain period of time, or if an object which exists inside the area disappears, an event is created. You can enter the
duration to be recognized as an event.
￭ Loitering : Creates an event when the motion of a loitering object in the virtual area is detected. You can enter the duration to be recognized as
an event.
– Add : After selecting the desired area item, set the area on the preview screen.
– Always : Detects motion regardless of time.
●
Sensitivity : You can set the motion detection sensitivity for the virtual line and the virtual area.
– Schedule : Detect motion only during the set period. Click &lt;Setup&gt; to set the detection schedule.
●
Detection result display : You can overlay the detection area over video.
●
Activation time : You can set the activation time to recognize motion analysis.
￭ Each camera product support different features. For more information, see the camera manual or help.
– Always : Detects motion analysis regardless of time.
– Schedule : Detects motion analysis only during the set period. Click &lt;Setup&gt; to set the detection schedule.
●
Object size : You can set the size of the object to recognize the motion.
– Click &lt;Setup&gt; to select the minimum/maximum size and set the object size on the preview screen.
●
Object : You can set the object to enable video analytics.
￭ Objects are visible only when an AI camera is connected.
￭ Object details may vary depending on the recorder model.
￭ Each camera product support different features. For more information, see the camera manual or help.
58_ setup
Tampering
Setup &gt; Event &gt; Event setup &gt; Tampering
Event Rule Setup
You can set the event trigger and action rule to output an alarm when an event occurs.
Setup &gt; Event &gt; Event rule setup
• setup
●
Tampering detection : You can set whether to enable tampering detection.
●
Sensitivity : Sets the tampering detection sensitivity.
￭ Since tampering detection is designed for optimal performance based on the sensitivity level by the user, there may be no noticeable
change in the tampering detection performance depending on the sensitivity level under normal monitoring conditions.
Video loss
Setup &gt; Event &gt; Event setup &gt; Video loss
●
Add : Adds a new event rule by selecting from rule creation or rule copy.
●
Delete : Deletes the selected event rule.
●
Enable : Specify whether to enable the corresponding event rule.
●
Rule name : Displays the name of the event rule. You can change the name of the event rule by clicking &lt;
●
Schedule : Displays the schedule set in the event rule.
●
Event trigger : Displays the event trigger set in the event rule.
&gt;.
￭ The event trigger will be displayed in the live video window when an event is received, and will be saved as an event log record.
Item
Description
Motion detection
IVA
Face detection
Auto tracking
Tampering detection
●
Sensitivity : You can set the video loss detection sensitivity. Depending on the sensitivity level (5 second
intervals), you can delay the occurrence of an event from 15 seconds (level 1) up to 60 seconds (level 10) later.
Defocusing detection
Fog detection
Audio detection
Sound classification
Alarm input (camera), Alarm input (NVR)
English _59
setup
Item
Description
Register a new event rule
Video loss detection
SD Card
Dynamic event
Example) DigitalAutoTracking, Queue, ShockDetection, MaskDetection
ObjectDetection
Manual trigger
Video loss recovered
System event
(Change password, Upgrage, HDD state, Fan failure, Power On/Off, Start manual recording, End manual
recording, Recording error, Account locked)
●
2. Click &lt;Create rule&gt;.
Event action : Displays the event action set in the event rule.
Item
1. Click &lt;Add&gt; in the &lt;Event rule setup&gt; field.
●
Description
Record/Go to preset
Alarm output
3. Set the details when the event rule setting window is displayed.
●
Rule name : Enter the name of the event rule.
●
Event trigger : Click &lt;+ Add trigger&gt; to set the event trigger and channel.
E-mail
FTP
Transfer images to FTP server
￭ Event triggers will be displayed on the live screen when an event occurs and are used for event log recording.
￭ To select a channel to detect an event trigger, click or drag the desired channel in the channel table. It will be displayed in orange when a
Monitor event
User coding
●
Edit : Changes the registered event rule.
￭ Up to three event triggers can be added.
￭ The event trigger option may vary depending on the recorder model.
￭ Duration is the waiting time to recognize the occurrence of a selected event. You have to select two or more event triggers to set this option.
The event action will run only when all the selected event triggers occur within the duration time.
Mobile push notification
Shutdown
Copy rule : When you select one of the event rules already created, it is added to the events list.
You can click &lt;
&gt; to modify the rule name.
channel is selected.
●
Schedule : Select the schedule to run the event action.
●
Event action : Click &lt;+ Add action&gt; to set the event action.
– Record/Go to preset : Set the PTZ preset to be displayed when an event occurs. Click &lt;
presets for each channel.
&gt; to set camera
– Alarm output : Set the alarm out to be generated when an event occurs. Select the output terminal
according to the number of alarm terminals on the recorder to set the alarm duration.
– E-mail : Set up users to receive e-mail when an event occurs. Click &lt;
e-mail.
￭ Set the interval for sending events in the “Setup &gt; Network &gt; E-mail &gt; Events&quot; menu.
&gt; to select users to receive the
– FTP: When an event occurs, the images are transferred to the designated FTP server. The overlapping
events that occurred during the set delivery interval will be sent as text in an html format file.
￭ Set the FTP connection and delivery interval in the “Setup &gt; Network &gt; FTP&quot; menu.
60_ setup
– Mobile push notification : When an event occurs, the event push notification will be displayed on the
connected smart phone.
ONVIF Setup
– Monitor event : When an event occurs, the screen of the corresponding channel will be displayed by
switching to the live screen. When selecting event monitoring, set the alarm duration in consideration of
network conditions.
You can set the details related to camera events registered with the ONVIF protocol.
Setup &gt; Event &gt; ONVIF setup
• setup
– Shutdown: When an event occurs, a pop-up window will appear. You can select &lt;Shutdown&gt; or
&lt;Cancel&gt;.
– User coding: It can be selected when &lt;Manual trigger&gt; is set. You can set the WISENET camera to
execute the SUNAPI command entered in &lt;User coding&gt; when an event occurs. Click &lt;Test&gt; to test the
execution of the entered SUNAPI command.
￭ Event action will run only when all set event triggers occur. If only one of the multiple events set has occurred, the event action will not run.
￭ Set the event action only when necessary.
4. Click &lt;OK&gt; at the bottom of the setting window to register the event rule.
Alarm Input
You can set the operation of the alarm sensor.
￭ This function is not supported in some models.
Setup &gt; Event &gt; Alarm input
●
●
No. : Select the channel to which the ONVIF camera is registered.
●
Camera event : It shows the list of all the events supported by a camera by using the ONVIF protocol.
●
NVR event : You can map the list of events supported by a camera to events that the Recorder can detect. There
is no default value. It only shows the value sent by a camera.
Type : Set the mode in which the alarm sensor will operate.
– Off : Alarm sensor is disabled. Alarm is not used.
– N.O. (Normal Open) : Sensor is opened. If the sensor is closed, it generates alarm.
– N.C. (Normal Close) : Sensor is closed. If the sensor is opened, it generates alarm.
●
Channel : You can set the channel to execute an event action when a signal is input to the selected alarm.
This is possible when &lt;Alarm input(NVR)&gt; trigger and event action are set up in the &quot;Event&gt; Event rule
setup&quot; menu.
English _61
setup
Schedule
Setting the Device
When setting the event rule, you can set the operating time of the event action.
You can make the detailed settings for devices such as storage device and monitors.
Setup &gt; Event &gt; Schedule
Storage Device
You can set the storage device usage and check the setting status.
Checking and formatting the device
You can check storage devices and their capacity, usage as well as status.
The connectable storage devices are HDD and USB.
Setup &gt; Device&gt; Storage device &gt; Management
●
Add : Add a schedule by setting the desired day and time.
– Off : Displayed in white and no alarm will be output even if an event occurs.
– On : Displayed in orange and an alarm will be output only when an event occurs.
●
￭ Click &lt;
&gt; to change the schedule name.
Delete : Delete the selected schedule.
￭ You cannot delete the schedule in use.
￭ When the alarm is generated on the scheduled time, you can stop the alarm by canceling the schedule.
●
Device : Displays the storage device type.
●
No. : You can check the designated number for the built-in HDD.
●
Model : Displays the model name of the storage device.
●
Capacity : Displays the amount of storage device use and the full capacity.
●
Type : Displays the usage type of the storage device.
●
Status : Displays the current working condition of a storage device.
●
62_ setup
￭ If you want the find out about the location corresponding to the HDD number, refer to the &lt;HDD Map&gt;.
￭ If the Status is set to &lt;Not Defined&gt;, format the storage device before use.
Temperature : You can check the temperature of the HDD mounted in the Recorder.
●
Time : Displays the use time of an HDD.
●
Format : Select a storage device and click on format after which a format confirmation window appears.
Click on the &lt;OK&gt; button to format the selected storage device.
●
￭ The ARB feature is available only when your video is saved in the SD card after registering your Wisenet camera using the Wisenet protocol.
Storage Status : Displays the working status of a storage device. Click the &lt;View&gt; to display the storage status
window.
– Red : Displays the situation of video loss.
– Green : Displays the normal situation without video recording losses.
– View : Click &lt;View&gt; to see detailed information.
￭ HDD write : Displays the current rate of recording.
￭ Present loss : Displays the current recording loss rate.
￭ Worst loss : Displays the maximum amount of losses up until now.
￭ If loss is continuously generated, check the following.
●
HDD map : You can check the location according to the assigned number for the HDDs installed inside.
￭ Refer to this when servicing or installing an additional HDD.
￭ Do not add or remove an HDD while Recorder is running.
For more information, refer to the &quot;Troubleshooting (FAQ)” in the Appendix.
–– When data is lost due to system failure (reset the rate of data transferred from the camera)
–– When there is a problem in HDD recording performance due to an HDD malfunction (check the HDD error or replace the HDD)
￭ Formatting will delete all the recording data that has been saved. Be careful.
￭ While formatting is ongoing, you cannot record video.
￭ Do not remove a formatting device until it is finished.
￭ After installing an HDD, if the state of use of the HDD is &lt;Not Defined&gt;, format the HDD before use. (If the warning message persists after
formatting, replace the HDD with a new one)
●
ARB : Video that was not recorded due to a camera disconnection can be backed up after the connection with
the camera is re-established. Press the button and an &lt;Auto recovery backup (ARB)&gt; window is opened.
– Select HDD : Select a HDD to be set to ARB.
– Capacity : Shows the capacity of the HDD to be set as ARB.
– Select channel : Select a channel to run the ARB.
￭ You can select multiple channels. If you select &lt;All channels&gt;, all channels will be selected.
– ARB bandwidth : Select a bandwidth for the ARB function.
English _63
• setup
This is only supported in SUNAPI 2.3.2 or later.
￭ Set the profile bitrate used for recording a video in the SD card of camera to 6144 kbps or below.
For more information on how to set the SD card recording profile, see your camera manual.
￭ To use the ARB function correctly, both the camera and Recorder should be time synchronized with the time server.
Refer to the &quot;Setup &gt; Setting the System &gt; Date/Time/Language&quot; page in the Table of Contents.
￭ ARB function is activated when Recorder starts/when the channel camera set is reconnected/when an Recorder recording missing section
recurs at regular intervals after Recorder starts.
￭ Recorder recording missing section that can be restored with the ARB function is for 24 hours backwards from the point when the ARB
function is activated.
￭ You can check which channels have ARB function activated through the message on each channel screen that is displayed when selecting
a channel.
Refer to the &quot;Live &gt; Live screen mode &gt; Channel Information Display&quot; page in the Table of Contents.
￭ For automatically recovered files through ARB, refer to the &quot;Search &gt; ARB Search&quot; page in the Table of Contents.
￭ ARB storage capacity is recommended to be at least one day.
Example) If you saved 64 channels with 1 Mbps each, the ARB capacity should be set to 0.7 TB or higher.
setup
Connecting the iSCSI
Adding an iSCSI device
This function is only available for products that support iSCSI. For products that support iSCSI, refer to the
&quot;Functions Supported by Model&quot; page.
When connecting an iSCSI device to the recorder, you can search for the iSCSI device and connect and disconnect
it.
Setup &gt; Device&gt; Storage device &gt; iSCSI
1. In the iSCSI window, click on the &lt;Add&gt; button.
2. In the &lt;Add iSCSI&gt; window, enter your IP address and port number and click &lt;Search&gt;.
●
Add : Add an iSCSI device.
●
Delete : Delete the registered iSCSI device.
●
Model : Displays the iSCSI model name.
●
iSCSI name : It displays the name of iSCSI in compliance with the iSCSI protocol format.
●
Capacity : It displays the currently used amount/total capacity of iSCSI devices.
●
Status : Displays the status of an installed iSCSI device.
List of products supported
Promise Technology vessRAID 1740i / 1840i / 2600i 1ea JBOD 3ea / SRB-160S
64_ setup
3. In the &lt;iSCSI name&gt; list, click on a device to add.
4. After entering ID/password, click on the &lt;Apply&gt; button.
￭ iSCSI device requires an independent port. Use a general port instead of a camera port.
￭ When using a hub to connect an iSCSI device with recorder, make sure to use the GIGA hub and to use an independent network to save data
normally.
￭ When the Recorder is connected to an iSCSI device, if you change the iSCSI equipment setting, a problem can occur.
￭ A HDD to be mounted in vessRAID should be listed in the RAID compatibility list.
￭ Each volume of an iSCSI device is recommended to be 16 HDDs.
￭ When you register an iSCSI device in the Recorder for the first time, you need to format it first.
￭ The iSCSI lun mapping function is supported.
￭ If you activate the LUN mapping function in the iSCSI device, the LUN can only be connected to a Recorder which is mapped.
￭ More than one mapped lun should be available to connect to the initiator when using lun mapping.
￭ An internal HDD must be mounted in the Recorder before connecting the iSCSI device.
￭ For the stable communication of large data, register only one iSCSI device to Recorder to use it.
RAID mode setting
RAID mode setting
This function is only available for products that support RAID. For products that support RAID, refer to the
&quot;Functions Supported by Model&quot; page.
1. Click on the &lt;Enable&gt; or &lt;Setup&gt; button.
If you enable the RAID (Redundant Array of Independent Disks) mode, you can safely recover your data even if
your system HDD is damaged.
RAID for each product
●
Enable : You can select whether or not to use the RAID mode.
●
Shows the RAID types supported by each product.
• setup
●
2. In the use RAID window, select settings of RAID and click on the &lt; OK&gt; button.
– 8 HDDs model : Supports Array 1
– 16 HDDs model : Supports Arrays 1 and 2
Setup &gt; Device&gt; Storage device &gt; RAID
Product
32-channel model
64-channel model
RAID type
Level 5, level 6
3. It will show the list of HDDs that compose a RAID. In the RAID screen, click on &lt;OK&gt;.
4. The data deletion and system rebooting message window will appear. You can click on the &lt;OK&gt; button to
reboot the system for RAID mode setting.
5. When RAID building is complete, select &quot;Setup &gt; Device &gt; Storage device &gt; RAID” to check the build.
￭ If you disable the RAID mode at RAID level 5 or 6, then every RAID array will be canceled. If you want to cancel only one of RAID arrays in
use, then go to the setup window and disable that specific RAID array.
●
RAID status : Displays the operational status of the RAID.
– Active : Signals the fact that the RAID is operating normally.
– Degraded : It is displayed when the one or more HDDs that make up the RAID are malfunctioning. When the
maximum number of HDDs allowed in the RAID level are malfunctioning, if an additional HDD malfunctions,
you cannot use or restore the RAID. Immediately, replace the HDD and proceed with restoration.
￭ For more information about how to replace the HDD and recover the RAID array, refer to the &quot;Setup &gt; Setting the Device &gt; Storage device&quot;
page in the Table of Contents.
– Rebuilding : Indicates that the RAID array is in the recovery process. At RAID level 5 or 6, if the max number
of HDDs allowed by the RAID level is malfunctioning, and one more HDD caused malfunction during
rebuilding, then you cannot recover or use the RAID array.
– Fail : This means that the RAID cannot be used or restored.
●
Model : Displays the registered RAID model.
●
Status : Displays the current operating condition of the HDDs installed in a RAID.
– Active : Displays that the HDD is operating normally.
– Faulty : It displays that the HDD is malfunctioning. You need to immediately replace the HDD for smooth
recovery of the RAID.
– Check : A problem occurs on the HDD, requiring replacement or inspection.
– Ready : If recovery of 2 HDDs is required in the RAID 6 state, HDDs for which rebuild is pending are displayed.
●
Capacity : It shows the total capacity of the HDDs that composes a RAID.
●
Temperature : You can check the temperature of HDD(s) that compose a RAID.
￭ If the Status of HDD is displayed as Check or Replace under &lt;Management&gt;, you cannot use it when configuring RAID.
￭ When the RAID mode is in use, it is recommended to use HDDs with the same storage space from the same manufacturer.
￭ If you enable or disable the RAID mode, existing data will be deleted. If you need to keep your old data, export it first.
￭ RAID Array capacity calculation
–– When you build the RAID in level 5, the available capacity of a RAID is (the least HDD capacity) x (total number of HDDs -1).
–– When you build the RAID in level 6, the available capacity of a RAID is (the least HDD capacity) x (total number of HDDs -2).
￭ If you use HDDs with different capacity, the HDD with the smallest capacity will be used to build a RAID.
Recovering RAID Array
1. If the HDD number whose &lt;Status&gt; is shown as Faulty or Check is recognized, check the location of HDD to
be replaced on the HDD map.
2. Replace the malfunctioning HDD from the recorder with a new HDD.
3. When the recovery starts, the LED of the replaced hard disk lights up in yellow.
In the &quot;Setup &gt; Device &gt; Storage device &gt; RAID&quot; menu, you can check the recovery progress.
￭ Replace it with the same model of HDD or an HDD of the same capacity from the same manufacturer.
￭ A HDD used to build the RAID should be one of the recommended models.
If it's not possible to use the same model of HDD, then use the HDD with the same capacity from the same manufacturer should be used.
￭ If you remove the power cord while using the RAID, it can damage it, so be careful.
For reliable power, it is recommended you use the UPS.
￭ A new HDD to be replaced should be one that is not RAID configured.
English _65
setup
Distributed Recording
S.M.A.R.T
This function is only available for products that support distributed recording. For products that support
distributed recording, refer to the &quot;Functions Supported by Model&quot; page.
You can check the connection status and details of the hard disk mounted in the recorder.
You can save recordings in a distributed manner by distributing HDD(s) of each group.
Setup &gt; Device &gt; Storage device &gt; Distributed recording
●
Record type : Select a storage type from &lt;Continuous recording&gt; or &lt;Distributed recording&gt;.
●
Initialization : Settings that are provided when &lt;Distributed recording&gt; is selected are configured as the
default settings.
: Update values such as hard disk capacity, input, and storage date to the latest data.
●
●
Group : Select a group to distribute the recording. If you select a group, a list to select a camera to assign opens
below.
●
HDD : The number and kind of currently available HDDs are activated.
●
External : Select an external storage device on which recordings will be stored.
●
Capacity : Displays the currently used capacity and entire capacity of an HDD that is selected in the group.
●
Receive : Displays the recording data volume of a channel selected in the group.
●
￭ If the input value exceeds 200 Mbps, it will be displayed in red.
Days : Displays the number of storable days for the input from the selected channel in the group on the HDD.
￭ Example) 3 days and 12 hours is displayed as 3.5.
●
HDD map : You can check the location according to the assigned number for the HDDs installed inside.
●
Channel list : The button state of the channel list is as follows.
–
: Channel selected in the current group.
–
: Channel selected in other group.
–
: Channel that is not currently selected. Please add this channel to the group.
66_ setup
￭ Recording cannot be performed while saving changes in distributed recording settings.
￭ To add more HDDs for distributed recording, install them in the order of 1, 5, 2, 6, 3, 7, 4 and 8.
Setup &gt; Device&gt; Storage device &gt; S.M.A.R.T
Monitor
Extended monitor setting
You can set the information displayed on the monitor as well as the output system.
This function is only available for products that support the use of an extended monitor.
Setup &gt; Device &gt; Monitor
For products that support extended monitor, refer to the &quot;Functions Supported by Model&quot; page.
• setup
Monitor settings
You can set the monitor output related screen displays, switching time, video display, etc.
1. Select &lt;Extend these displays&gt; for video display and click &lt;Setup&gt;. You can change the layout of the
extended monitor.
2. Select the Screen division you want.
●
OSD : Only checked items among date, time, channel name and information icon will be displayed on the
monitor screen.
– You can adjust the size of the channel name displayed on the live screen. Select from among &lt;Default&gt;,
&lt;Large&gt;, &lt;Very large&gt;.
●
Multiple displays : Set the video display resolution.
For products that support the extended monitor, you can set the resolution after selecting &lt;Duplicate these
displays&gt; or &lt;Extend these displays&gt; mode for video display.
– Duplicate these displays : You can set the video display resolution of the primary monitor and secondary
monitor to be the same.
If you set a resolution exceeding 1920 x 1080 while operating in clone mode, the video will not be displayed
to the secondary monitor.
3. Select as many channels from the channel table as the selected number of Screen division channels to view
the videos on the monitor screen.
￭ When extended mode is selected, the maximum resolution of the image output on the primary monitor (HDMI) is limited to 1920 x 1080.
￭ If the newly selected resolution does not fit with the monitor, the display won’t function properly. In this case, wait until the native
resolution is restored and then switch to another resolution of your choice.
￭ Set up Event Display and Sequence Switching Time in consideration of the network environment time.
￭ The profile used in the live output of the expanded monitor uses a remote profile. If the user changes the remote profile, the video output
of the expanded monitor may be affected.
￭ If the monitor is in clone mode, you can specify up to the split mode supported by the recorder. When the monitor is set to extended mode,
you can split the screen of the Secondary monitor up to 36-split mode depending on the recorder model.
￭ The dynamic layout function can only be set on the primary monitor.
– Extend these displays : You can set the video display resolution of the primary monitor and secondary
monitor respectively.
￭ Primary monitor supports 4K resolution (or 1080p), and Secondary monitor supports 1080p resolution.
￭ If the newly selected resolution does not fit with the monitor, the display won’t function properly. In this case, wait until the native
resolution is restored and then switch to another resolution of your choice.
￭ The video output for Primary monitor and Secondary monitor may differ depending on the recorder model.
–– Primary monitor: HDMI
–– Secondary monitor: HDMI or VGA
English _67
setup
Screen position setup
Text
Some monitors many not display information (camera name, icon) about the Recording, depending on the
condition. Then, you can change the display position of the data.
You can set the POS device setting to send text information and text event information.
Device Settings
You can make detailed settings for the POS device connected to the recorder.
Setup &gt; Device &gt; Text &gt; Device
1. From the monitor setup menu, select &lt;Screen position setup&gt;.
2. Using &lt;
&gt; button to adjust the screen that is cut off.
3. Click &lt;OK&gt;.
￭ This product only supports 30Hz at 4K resolution.
●
Device : Displays the text device name registered by the user.
●
Enable : Specifies whether to enable text device.
●
Channel : Select a channel to add a device from a channel table.
●
Port : Display a port number that is set.
●
Encoding type : Select an encoding type to use from a list.
￭ Epson, Wincor Nixdorf, Axiohom, Radiant System, IBM POS device, and ANPR protocols are supported.
￭ POS device connected to Recorder uses TCP/IP communication protocol.
68_ setup
Registering a Text Device
Text Event Settings
You can set the text to receive an alarm when an event occurs.
Setup &gt; Device &gt; Text &gt; Event
• setup
1. Click the desired item in the text device list.
2. Enter the device information to register in the &lt;Modify the text device&gt; window.
●
Device name : Enter the desired text device name.
●
Text device : Specify whether to enable text device.
●
CH : Select a channel to add a device from a channel table.
●
Pre-event playback time : Enter the start time of the playback from how many seconds before when an event
occurs.
●
Port : Enter the device's port number.
●
Encoding type : Select the encoding type of the device.
●
Device type : Select the device type.
●
●
Total amount : Set the condition of the total amount to be notified when a text event occurs. Check whether
the total amount is used, and then select the base amount and range.
●
Keyword : You can register or delete keywords to be notified when an event occurs.
– If the &lt;Add&gt; button is clicked, a screen to add keywords pops up.
– If you select one of the added keywords to delete and click the &lt;Delete&gt; button, the selected keyword will
be deleted.
￭ When entering the total amount, set it to 15 characters or less, including minus and decimal point.
￭ When entering keywords, set them within 50 characters. Up to 20 keywords can be specified.
Start / End : You can select starting and ending character strings.
– A text string can be entered by using texts, hex codes, and regular expressions.
– Text : Enter a text string to search for.
– Hex Code : Enter a hexadecimal text string to search for.
(Your input should not be in hexadecimal —e.g. 1b40, 1b69)
– Regular expression : Enter a regular expression to search for text strings that follow specific rules.
3. Click &lt;OK&gt;.
English _69
setup
Setting the Network
Connecting and Setting the Network
You can set various network functions, such as monitoring live video by connecting to a network from a remote location
and receiving an event by e-mail.
Networking may differ from the connection method, check your environment before setting the connection
mode.
IP &amp; Port
You can set the network connection route and protocol.
When no router is used
●
Setting a network connection
– Network Settings : Set the &lt;IP type&gt; of the connected recorder to &lt;Manual&gt;.
Sets the protocol and environment of the network.
Setup &gt; Network &gt; IP &amp; Port &gt; IP address
Manual mode
– Internet connection : Static IP, leased line, and LAN environments allows connection between the Recorder
and remote user.
●
￭ Consult your network manager for IP, Gateway and Subnet Mask.
DHCP mode
– Internet connection : Connect the Recorder directly to a cable modem, DHCP ADSL modem or FTTH
network.
– Network Settings : Set the &lt;IP type&gt; of the connected recorder to &lt;DHCP&gt;.
When a router is used
￭ To avoid IP address conflict with the Recorder's static IP, check followings :
●
Setting the Recorder with a static IP
– Internet connection : Connect the recorder to an IP router where cable modem is connected, or connect the
recorder in the local area network (LAN) environment.
●
●
Network : Each product supports a different number of network ports. If it supports two or more network
ports, you can set the network for each function as follows.
●
Network 1(Camera) : It can be used as a port for connecting a camera. If you connect a camera, then the
camera video will be transmitted. Using the network information, you can access the web viewer.
●
Network 2 (Viewer) : It can be used as a common port for camera and web viewer connection.
●
Network 3 (iSCSI) : It can be used as a dedicated port for iSCSI connection.
●
￭ Only provided for products that support Network 3.
Network (All) : It can be used as a common port for connecting camera, web viewer, and iSCSI.
– IP type : Select the type of network access.
– IP address, Subnet Mask, Gateway, DNS
￭ Manual : IP address, subnet mask, gateway, and DNS can be directly entered.
￭ DHCP : IP address, subnet mask, gateway, and DNS can be automatically set.
●
Transfer bandwidth : Enter the max data volume of a rate for transfer.
●
Default gateway : Select the default gateway. If there are multiple network ports, set one of them as the default
gateway.
￭ The DNS value of DHCP can be directly entered only if you have selected &lt;Manual&gt;.
70_ setup
Setting the Recorder Network
1. Set the &lt;IP type&gt; of the connected recorder to &lt;Manual&gt;.
2. Check whether the set IP address is in the static IP range provided by the Broadband Router.
IP Address, Gateway, and Subnet Mask : Consult your network manager.
￭ If a DHCP server is configured with starting address (192.168.0.100) and end address (192.168.0.200), you should set the IP address out of
the configured DHCP range (192.168.0.2 ~ 192.168.0.99 and 192.168.0.201 ~ 192.168.0.254).
3. Check the Gateway address and subnet mask are equal to those set in the Broadband Router.
●
Setting the DHCP IP Address of the Broadband Router
1. To access the Broadband Router's configurations, open a web browser on the local PC that is connected to the
Broadband Router and enter the router's address (ex : http://192.168.1.1).
– Once connected to the Broadband Router, it prompts with password. While entering nothing to the User
Name field, enter “admin” into the password field and press &lt;OK&gt; to access the router configurations.
– Access the router's DHCP configuration menu and set its DHCP server activation, and provide the start and
end address.
￭ Start address : 192.168.0.100
￭ End address : 192.168.0.200
￭ Above steps may differ from the router devices depending on the manufacturer.
Port Setting
Setup &gt; Network &gt; IP &amp; Port &gt; Port
A remote user can network a recorder using a DDNS address in a dynamic IP system. If you cannot connect with a
dynamic IP, you can easily access using a P2P service.
Accessing using DDNS address in the dynamic IP environment
In the dynamic IP environment such as xDSL/Cable modem, the router's WAN IP can be changed, so we provide
DDNS (Dynamic Domain Name Server) service so that you can always access the recorder with only the DDNS
address even in the dynamic IP environment.
Before using Wisenet DDNS &amp; P2P, please set up the network connection and DDNS first.
DDNS Setting
Setting DDNS in the Recorder
Set &lt;Protocol type&gt; to &lt;TCP&gt; in the &quot;Setup &gt; Network &gt; IP &amp; Port &gt; Port&quot; menu of the connected recorder.
DDNS Settings of the Router
Select the corresponding menu for the network transfer protocol of the router.
Setting up UPnP of Router
Refer to the router's documentation to enable the UPnP function of the router.
Setting the Wisenet DDNS &amp; P2P
Setup &gt; Network &gt; DDNS &amp; P2P
●
Protocol type : Select the protocol type among TCP, UDP Unicast and UDP Multicast.
●
RTSP port : It is used to transmit the video over the network. The initial value is &lt;558&gt;.
●
UDP port : Activated when an UDP item is selected in protocol type. The initial value is &lt;8000-8159&gt;,
and the setting value changes in 160 units.
– UDP : It has less stability and faster speed when compared to TCP, and recommended for local area network
(LAN) environments.
●
Multicast IP address : Enter the IP address directly when selecting an UDP Multicast.
●
Multicast TTL : Enter the TTL value when selecting an UDP Multicast. The initial value is set to &lt;5&gt;, and enter a
value between 0 and 255.
●
HTTP port : Enter the port value for the HTTP web viewer. The initial value is set to &lt;80&gt;.
●
HTTPS port : Enter the port value for the HTTPS web viewer. The initial value is set to &lt;443&gt;.
￭ HTTPS is an enhanced version of the HTTP web communication protocol. If security is important when accessing the web viewer, enable the HTTPS
●
Enable : Click &lt;Enable&gt; to test the connection to see if the current recorder can be connected remotely.
When the connection is successful, a QR code is created.
￭ It connects to Wisenet DDNS first. If it does not connect to DDNS, it automatically connects to P2P.
port.
●
Cam proxy port : Sets the camera proxy port. The initial value is set to &lt;10001&gt;.
English _71
• setup
2. At this stage, make the local PC's windows network configurations to the below example :
Example) IP : 192.168.1.2
Subnet Mask : 255.255.255.0
Gateway : 192.168.1.1
DDNS &amp; P2P
setup
￭ In a double NAT environment or if the router's port is not configured, the DDNS status will be displayed as &lt;Successful&gt;, but the DDNS
connection from the viewer to the recorder may fail.
￭ You must be connected to an external network for a DDNS connection. (If there are two or more networks, be sure to connect an external
network to the network set as the &lt;Default gateway&gt;.)
￭ If you are setting up a port that is already in use, then the connection might fail. Check the port setup of your router.
￭ If the viewer is connected through P2P instead of DDNS when connecting to a recorder, performance may be lower than that of the DDNS
connection. You can check the current connection method (DDNS or P2P) in each viewer.
￭ DDNS is a short form of Dynamic Domain Naming System.
DNS (Domain Name System) is a service that routes a domain name consisting of user friendly characters (ex : www.google.com) to an IP
address consisting of numbers (64.233.189.104).
DDNS (Dynamic DNS) is a service that registers a domain name and the floating IP address with the DDNS server so that the domain name
can be routed to the IP address even if the IP is changed in a dynamic IP system.
●
Connecting to the Viewer
To connect to the Wisenet mobile from your smartphone
1. Install and run the &quot;Wisenet mobile&quot; app on your smartphone.
You can scan the QR code of the recorder on the &lt;Add device&gt; screen.
2. When the QR code is scanned, the &lt;Product ID&gt; shown in the recorder is automatically reflected in the
mobile viewer, and you can use the mobile viewer by entering the recorder ID/password.
3. Then, when you run the &quot;Wisenet mobile&quot; app, it will be automatically connected to the recorder and you can
monitor it easily with your smartphone.
Quick connect (UPnP) : To use the function, set to &lt;Enable&gt; after connecting the Recorder to a UPnP router.
The message about the progress appears when connecting to Quick connect (UPnP).
To connect to the Wisenet Viewer from your PC
– Quick Connect Success : Message for a successful connection.
1. Go to https://www.hanwha-security.com on your PC.
Install and run the &quot;Wisenet Viewer&quot; app.
– Invalid Network Configuration : Message appears if the network configuration is not valid. Check the
configuration.
– Please enable UPnP function of the router. : Message appears if the router requires UPnP function
enabled.
– Failed to find the router. : Message appears if the router is not found. Check the router's configurations.
– Please restart the router. : Message appears if the router should be restarted.
– Quick Connect not supported in UDP mode. : Set &lt;Protocol type&gt; to &lt;TCP&gt; in the &quot;Setup &gt; Network &gt;
IP &amp; Port &gt; Port&quot; menu of the connected recorder.
– Connection Failed. : If the connection fails due to an unknown error, the message is displayed.
￭ If there is a port conflict, it will automatically change to another port. You can check the changed port information in the &quot;Setup &gt;
Network &gt; IP &amp; Port &gt; Port&quot; menu of the connected recorder.
￭ If there is a port conflict, check the port forwarding or UPnP settings in the user manual of the connected router.
Setting the Public DDNS
●
DDNS site : Select whether to use DDNS and the site registered when using it.
●
Host name : Enter the host name registered with the DDNS site.
●
User name : Enter the user name registered with the DDNS site.
●
Password : Enter the user password registered with the DDNS site.
72_ setup
2. Select &lt;IP type&gt; to &lt;DDNS/P2P&gt; in the &quot;Setup &gt; Device &gt; Device list &gt; Add &gt; Manual&quot; menu.
3. Enter the recorder ID/password and &lt;Product ID&gt;, and then click &lt;Register&gt;.
The information of the current recorder will be displayed, and you can use the &quot;Wisenet Viewer&quot; app.
To connect to the WebViewer from your PC
If you connect to http://ddns.hanwha-security.com/product ID including &lt;Product ID&gt; in the local PC address
bar, the recorder's web viewer screen will appear.
IP Filtering
HTTPS
You can prepare the list of IP addresses to allow or block access to a specific IP address.
You can choose a secured connection system or install a certificate.
Setup &gt; Network &gt; IP filtering
Setup &gt; Network &gt; HTTPS
• setup
●
Filtering type
●
– Deny registered IP : Access to the registered IP address will be limited.
– Allow registered IP : Only registered IP addresses can be accessed.
●
Enable : Select whether to enable registered IP filtering.
●
IP address : Displays the registered IP address. Double click the IP address to change the settings.
●
Prefix : Displays the prefix to be filtered. Double-click the prefix to change the settings.
●
Filtering range : If you enter an IP address or prefix, then the range of IP addresses blocked or permitted will be
displayed.
– HTTP (Does not use a secure connection) : Transmits data without encryption.
– HTTPS (Secure connection mode using a unique certificate) : Establishes a secure connection using a
unique certificate provided by the recorder.
￭ Mutual authentication : Mutual authentication can be performed to enhance security. If you select &lt;Allow all connections&gt;, you can access
the storage device even if mutual authentication is not performed. If you select &lt;Allow only mutually authenticated connections&gt;, you can
access the storage device only when mutual authentication was successful.
￭ If a camera's IP address is not included in the Permit list or is in the Reject list access to it will be rejected.
￭ For IPv4, camera IP filtering through PoE port is not immediately applied. (Previous connections are maintained, and filtering is applied on
– HTTPS (Secure connection mode using the public certificate) : Establishes a secure connection using a
public certificate. You can select this after installing a public certificate.
next login.)
To register the IP addresses to filter
●
2. Click &lt;Add&gt; at the bottom of the screen.
3. When the additional window is displayed, set the details.
IP filtering : Select whether to enable IP filtering.
●
IP address : Enter the address to enable IP filtering.
– Version : You can select the TLS protocol version to use for encrypted communication.
￭ If &lt;Cipher mode&gt; is set as &lt;Secure cipher suites only&gt;, you can select only &lt;TLS 1.2&gt; or &lt;TLS 1.3&gt;.
￭ If the recorder is connected to the external internet or installed in an environment with high priority for security, making a secure
– When entering an IP address, a value in the range 0-255 must be entered to register.
●
connection is recommended.
Prefix : Enter the prefix value.
4. Click &lt;OK&gt; to complete.
￭ To delete a registered item, select the check box of the item to be deleted and click &lt;Delete&gt; at the bottom of the screen.
TLS settings : You can select the Cipher mode or TLS version to use for encrypted communication.
– Cipher mode : Cipher suites are provided by combining different algorithms for use in TLS-encrypted
communications, such as key exchange, authentication, and encryption.
&lt;Secure cipher suites only&gt; uses only high-security cipher suites.
For backward compatibility, select &lt;All compatible cipher suites&gt;. However, security may be poor, as it
includes all cipher suites, whether secure or not.
1. Select the IP type tab you want to register from IPv4 or IPv6.
●
Secure connection system : You can select a type of secure connection system based on the service
environment and the security level.
HTTPS (Hypertext Transfer Protocol Secure) is a more secure version of HTTP that exchanges data through the
encryption and decryption of the user's page request at the TLS (Transport Layer Security).
●
Install a public certificate : You can scan and register a public certificate to be installed. To install a certificate,
you must install a certificate file or key file issued by a certificate authority. Click &lt;Install&gt; to register the
certificate.
￭ In the &lt;HTTPS (Secure connection mode using the public certificate)&gt; mode, you cannot install or delete a public certificate. Change to &lt;HTTP
(Does not use a secure connection)&gt; or &lt;HTTPS (Secure connection mode using a unique certificate)&gt; mode before proceeding.
￭ Install the certificate file extension as .crt and the key file extension as .key.
￭ For certificate and key files, use PEM format generated by RSA (2048 or higher recommended) or ECC.
￭ For certificate and key files, use PKCS#1 or PKCS#8 without a password.
English _73
setup
802.1x
FTP
When connecting to a network, you can select whether to use the 802.1x protocol and install a corresponding
certificate.
When an event occurs, it can be configured to send the event image to the FTP server.
Setup &gt; Network &gt; FTP
802.1x is an authentication system between a server and a client, which prevents hacking, virus infection, and
information leakage of transmitted and received network data.
802.1x can be used to block the unauthorized client access and increase security by allowing only authenticated
users to communicate.
Setup &gt; Network &gt; 802.1x
●
●
●
●
EAPOL version : Select the EAPOL version to be used as protocol.
￭ Some switch hubs will not operate if you set them to version &lt;2&gt;. Select the version &lt;1&gt;, which is the EAPOL default.
ID : Enter the ID provided by the RADIUS server administrator.
￭ If the entered ID does not match the ID of the client's certificate, it won't be processed properly.
●
Server address : Enter the FTP server address to connect to.
●
Port : Enter the connection port. The initial value is set to &lt;21&gt;. Enter a value between 1 and 65535.
●
ID : Enter the user ID to authenticate when connecting to the FTP server.
●
Password : Enter the user password to authenticate when connecting to the FTP server.
●
Upload directory : Enter the path of the FTP server where the transmitted event image will be saved.
●
Passive mode : Check &lt;Enable&gt; if passive mode is required due to firewall or FTP server settings.
●
Enable Transport Layer Security (TLS) : Select between &lt;Disable&gt; and &lt;TLS (if available)&gt;.
●
Delivery interval : Select the delivery interval for your event.
Password : Enter the password provided by the RADIUS server administrator.
￭ If the password you entered does not match that of the client's private key, it won't be processed properly.
Certificates : Search for a device. Click on &lt;
&gt; to search for a device again.
●
CA certificates : Select this only if your public certificate includes the public key.
●
Client certificate : Select if the public certificate includes a client's authentication key.
●
Client private key : Select it if the public certificate contains the client private key.
￭ For successful implementation of the 802.1x operating environment, the administrator must use the RADIUS server.
In addition, the switch hub connected to the server must be a device that supports 802.1x.
￭ If the time setting of the RADIUS server, the switch hub and an recorder do not match, communication between them can fail.
￭ If a password is assigned to the client's private key, the server administrator should confirm the ID and password.
The ID and password allow up to 30 characters each. (But it only supports letters, numbers and special characters (&quot;-&quot;, &quot;_&quot;, &quot;.” 3 types) only.
Accessing non password-protected files is allowed without entering a password.
￭ The 802.1x protocol adopted by the Recorder is EAP-TLS.
￭ You need to install all three certificates to use 802.1x.
74_ setup
￭ If a series of events occurs, it will be sent at the set time, not on each event. The overlapped events that occurred during the set delivery interval are
sent as text in an html format file.
●
FTP test : Conducts the transfer test with the entered FTP server settings.
E-mail
Event Setting
You can send an e-mail to a Recorder-registered user at a specific time interval, or if an event occurs.
You can set the interval and type of the event that will be sent to the user.
Setup &gt; Network &gt; E-mail &gt; Event
SMTP Setting
Sets the SMTP mail server.
• setup
Setup &gt; Network &gt; E-mail &gt; SMTP
●
Delivery interval : Set the event interval.
￭ If a series of events occurs, the e-mail will be sent at the specified interval, not on each event.
Recipient Setting
●
Server address : Enter the SMTP server address to connect to.
●
Port : Enter the connection port.
You can create a group and add users to it or; you can delete users and change a group.
●
Enable authentication : Check this if the SMTP server uses user authentication.
The ID and password fields will be activated when the authentication is enabled.
Setup &gt; Network &gt; E-mail &gt; Recipient
– ID : Enter a ID to use authentication when connecting to the SMTP server.
– Password : Enter the password of the SMTP server user.
●
Enable Transport Layer Security (TLS) : Select one from &lt;Disable&gt; and &lt;TLS (if available)&gt;.
●
Sender : Use the virtual keyboard to enter the sender's e-mail address.
●
Test e-mail : Conducts the test on the server settings.
●
Click on &lt;
&gt; to add a group.
Enter the group name.
●
Select a recipient group to receive emails.
If a group is added, it will appear in the group list.
●
Click on &lt;
&gt; to add a recipient.
Select a group and enter names and email addresses.
If a group is created, you can add a recipient.
English _75
setup
SNMP
DHCP Server
The SNMP protocol allows system or network administrators to remotely monitor and configure the network
devices.
You can set the internal DHCP server and assign an IP address to the network camera.
Setup &gt; Network &gt; SNMP
Network Setting
Setup &gt; Network &gt; DHCP server &gt; Network
●
●
Enable SNMP v1 : SNMP v1 is used.
Enable SNMP v2c : SNMP v2c is used.
– Read community : Enter the name of read-only community to access the SNMP information.
– Write community : Enter the name of write-only community to access the SNMP information.
●
●
Enable SNMP v3 : SNMP v3 is used.
●
Network : You can set the IP range and time to activate as the recorder's DHCP server.
To set the DHCP server
– Password : Set the initial user password for SNMP version 3.
1. Click &lt;Setup&gt; of the network you want to set as a server.
Enable SNMP traps : SNMP trap is used to send important events and conditions to the Admin System.
2. When the network setting window is displayed, select &lt;Run&gt; for &lt;Status&gt;.
– IP address : Enter the IP address to which messages will be sent.
3. Enter the starting IP and end IP in the &lt;IP range&gt; field.
4. Fill in the &lt;IP lease time&gt; field.
5. Click &lt;OK&gt;.
The IP range entered is set as the DHCP server address of the network.
76_ setup
Checking the status
To set troubleshooting
You can check the IP address assigned to the current DHCP server, MAC address, and the connected network port
information.
1. Set one recorder to &lt;Standby&gt; mode and the other recorder to &lt;Active&gt; mode.
Setup &gt; Network &gt; DHCP server &gt; Status
2. In the recorder set to &lt;Active&gt; mode, enter the viewer port IP and administrator password of the &lt;Standby&gt;
recorder you want to connect to and click &lt;Connection&gt; under the status display.
3. Check the IP and status of the connected &lt;Active&gt; recorder in the &lt;Standby&gt; recorder.
• setup
Setup &gt; Network &gt; Failover
Failover
This function is only available for products that support failover. For products that support failover, refer to the
&quot;Functions Supported by Model&quot; page.
●
If the recorder cannot record due to a network failure, other recorders that have been prepared can record
instead.
– Standby : Recorder being prepared without recording. It will record instead of the &lt;Active&gt; recorder if a
problem occurs.
You can connect 32 'Active' recorders to one 'Standby' recorder.
￭ The recorder you want to configure for failover needs to be connected to both the camera and viewer ports to the local network.
￭ Failover configurations can only be set with recorders of the same model.
￭ Troubleshooting network interface supports IPv4 only.
￭ All recorders must have time synchronized. For more information about time synchronization settings, refer to the “Setup &gt; Setting the
System &gt; Date/Time/Language&quot; page in the Table of Contents.
￭ The network IP band in the recorder must be set to a different band.
–– Example of IP in a different bandwidth
Example 1) IP : 192.168.1.200, subnet 255.255.255.0
In the Example 1) above, since 255 of the subnet corresponds to 192.168.1, any IP in a format of 192.168.1.x has the same bandwidth.
An IP in a format of 192.168.2.x has a different bandwidth with an IP in a format of 192.168.1.x.
Example 2) IP : 172.16.1.200, subnet 255.255.0.0
In the Example 2) above, since 255 of the subnet corresponds to 172.16, any IP in a format of 172.16.x.x has the same bandwidth.
An IP in a format of 172.17.x.x has a different bandwidth with an IP in a format of 172.16.x.x.
Mode : Select either &lt;Active&gt; or &lt;Standby&gt; mode.
– Active : Recorder being recorded. Monitored by the &lt;Standby&gt; recorder.
In the case of active mode
●
Standby recorder IP : Enter the viewer port ID of a standby recorder to access.
●
Standby recorder password : Enter the administrator password of the standby recorder.
●
Status : Displays the current connection status.
●
Connection / Disconnection : Click the button to access or disconnect the access.
￭ For more information about network settings, refer to the “Setup &gt; Setting the Network&quot; page in the table of contents.
English _77
setup
Setting the System
In the case of standby mode
●
Device list &amp; status : Shows the status of the normal recorder currently connected to the standby recorder. To
delete the normal recorder connected, click &lt;Delete&gt; on the right side of the recorder.
￭ The standby recorder can only enable some functions in the &lt;System&gt;, &lt;Device&gt;, and &lt;Network&gt; menus. You can't use the
&lt;Record&gt; and &lt;Event&gt; menus.
￭ In the standby recorder, the previous operation will stop when a failover is performed during the playback or section export, and the screen
will move to the live screen.
State name
You can set the date, language, authority, etc. displayed when using the system, and query system information or log
information.
Date/Time/Language
You can check and setup the current Date/Time and time related properties, as well as the language used for the
interface on the screen.
Description
Ready
Setup &gt; System &gt; Date/Time/Language
Ready to be connected
Connected
Normal recorder and standby recorder connected (failover available)
Failover
Troubleshooting is being performed
Connected fail
Connection was attempted but failed
Authentication failure
Auth failed by entering an incorrect standby password when attempting to connect
Connected(Match Time Required)
Connected without time synchronization with the standby recorder
Connected(check camera port IP)
Even if the camera port of a normal recorder is connected to the viewer port of the standby
recorder or connected to the same viewer port, the IP port of the camera port is not matching.
Connected fail(check camera port IP)
The connection from the normal recorder's camera port to the standby recorder's camera port
failed.
Connected fail (It is a different model.)
Failed connection by connecting recorders of different models.
Example of setting up failover
– Subnet 1 ➡ Network 1 (Camera)
– Subnet 2 ➡ Network 2 (Viewer)
●
Date : Sets the date and its format that will appear on the screen.
●
Time : Sets the time and its format that will appear on the screen.
●
Time zone : Sets the time zone of your area based on the Greenwich Mean Time (GMT).
Recording Stream
Failover Monitoring
– Synchronize with NTP server : Specify the use of synchronization with the time server.
Fake Recording Stream
– NTP server address : Enter an IP or URL address of the time server.
– Subnet 3 ➡ Network 3 (iSCSI)
– Last sync : Displays the most recent synchronization time from the selected time server.
Subnet 1
– Enable as NTP server : If you select &lt;Enable&gt;, this recorder will act as a time server for another recorder or
network camera.
Subnet 2
Active
78_ setup
￭ GMT (Greenwich Mean Time) is standard World Time and the basis of world time zone.
Time sync : Specify the use of synchronization with the time server.
Click the &lt;Setup&gt; button to display time synchronization setup screen.
If you enable &lt;Synchronize with NTP server&gt;, the current time of the recorder is synchronized by the server
specified in &lt;NTP server address&gt;, and the time information cannot be manually changed.
●
Active
Standby
●
DST : Set up Daylight Saving Time with its period to make the time earlier than the GMT of its time zone by 1
hour during the set period.
●
Language : Select your language. Sets the language for the interface.
￭ Depending on the location of the product release, the language and standard time setup may vary.
●
Holiday : A user can select specific dates as holidays according to their own preferences. Select a holiday from
the calendar displayed by clicking &lt;Setup&gt;.
– The same applies to &lt;Record schedule&gt; or &lt;Schedule&gt; settings as holidays.
User
You can manage users, such as adding or deleting users and granting different authorities for each user.
Setting the Administrator
Setup &gt; System &gt; User &gt; Administrator
Example) If you select May 1 and check &lt;May 1Day&gt;, May 1 will be set as a yearly holiday, and if you check
&lt;May 1Day&gt; and &lt;First Friday l May&gt; May 1 of every year and all Fridays of the first week of May will be set as
holidays.
To use the calendar
●
ID : Change the admin ID.
●
Current PW : Enter the current PW.
●
New password : Enter new password.
●
Confirm new password : Enter the new password again.
￭ If &lt;Show password&gt; is selected, the password will no longer be hidden on the screen when you type it.
￭ The initial administrator ID is set to “admin” and you will need to configure the password in the installation wizard.
￭ Please change your password every three months to safely protect personal information and to prevent the damage of the information
1. Select year and month.
￭ Click &lt; &gt; on the right side of the year to change the year by one year.
￭ Click the &lt; &gt; to the right side of the month to change the month every 3 months.
theft.
Please, take note that it's a user's responsibility for the security and any other problems caused by mismanaging a password.
￭ If you click &lt; &gt;, a basic guide for password setup is displayed.
2. Select a date and click on the &lt;Apply&gt; button.
English _79
• setup
You can set and change Administrator's ID and password. The administrator can use and set all menu items and
functions.
setup
User setting
If you want to register a user
You can create user groups and set authorities for each group. You can manage user information such as
registering and deleting users in the created user group.
Setup &gt; System &gt; User &gt; User
1. Click on the &lt;
&gt; button to launch the user addition popup window.
To add a user, click on &lt;OK&gt;.
2. Select a group.
When registering a user, the selected group will be automatically registered.
If you want to add a group
1. Click on the &lt;
&gt; button to launch the Group Addition popup window.
If you want to add a group, click on &lt;OK&gt;.
2. If you click the group name item on the right, a virtual keyboard to enter the group name will appear.
Enter the group name to register.
￭ You can add a maximum of 10 groups.
If you want to set group permission
Set the access authority of the group.
Users in the group can only enable the menu to which they have been granted authority.
1. Select the menu to set group permissions.
Set the menu and click &lt;Setup&gt; on the right to display the detailed settings window.
●
Live channel : You can set permissions to access the live screen for each channel.
●
Search channel : You can set permissions to access the search menu for each channel.
●
Export : You can set the authority to access the export menu for each channel.
●
Menu : You can select and set the setting menu that can be accessed. A group user can only access the
menu selected. If you select the menu, the menu permission setting screen will be displayed.
●
Record, Stop recording, PTZ control, Remote alarm output control, Shutdown : You can set the menu to
grant access to users in the group.
￭ Permission-set menus will show up in the Live menu when users of the group log in.
2. Select &lt;Apply&gt;.
Users in the group will be given access to the set items.
80_ setup
￭ You can change the group after entering all the user information.
3. Enter a name, ID and password (confirm password) and enable or disable the viewer option.
If you activate use of &lt;Viewer&gt;, you will have the right to use the web viewer and the network viewer.
￭ If &lt;Show password&gt; is selected, the password will no longer be hidden on the screen when you type it.
4. Click &lt;Apply&gt;.
Registered user information will be saved.
When you want to delete the group and user information
1. Select the group or user to delete and press the &lt;
&gt; button.
2. The deletion confirmation window will appear and click on &lt;OK&gt;.
Restriction Settings
If the user has restricted access
Set user's restricted access or network restriction.
If a general user selects a menu to which they do not have access, an access restriction confirmation window will
be displayed. If all rights are restricted, only the accessible menu of the live screen menu will be displayed, and
only the user's own password can be changed.
Items with restrictions will require logging in for use.
Setup &gt; System &gt; User &gt; Restriction settings
• setup
●
Access restriction : You can set the menu to restrict the access for user.
To change the user password
– Checked (
If you log in with the user account of a group with restricted access, you just can change your own password.
) : Restricted
￭ Only those users who were given Permission for the menu in &lt;User&gt; can access the menu.
– Not checked (
●
) : Accessible
Setup &gt; System &gt; User
￭ Regardless of the Permission settings for the menu in &lt;User&gt; all users can access the menu.
Remote access restriction : You can restrict remote access for users.
– All viewers : Set all users to be unable to access the network and the web viewer.
– Web viewer : Set all users to be unable to access the web viewer.
●
Auto logout : A user will be automatically logged out if there is no operation on Recorder for over set period of
time.
●
ID manual entry : In the login window, select whether to enter ID.
1. Provide the login information.
2. Select &lt;User&gt; in &lt;System&gt;.
3. Please enter your current password.
4. Provide a new password. Enter the password you want to change in the password confirmation box again.
5. Select &lt;Apply&gt;.
The old password will be changed to a new one.
English _81
setup
System Management
To upgrade the current software version
You can check the current system version and update to a new version, export data, setting initialization, and
more.
Setup &gt; System &gt; System management &gt; Product information
Checking the System information
You can check the current software version and MAC address before proceeding with the upgrade.
Setup &gt; System &gt; System management &gt; Product information
1. Connect a device storing the software to be updated.
￭ It may take about 10 seconds to recognize the device.
￭ Upgradeable devices include USB memory, and network device.
￭ If you want to upgrade it on the network, the product should be connected to an external network.
Upgrade via the proxy server may not be enabled due to the restricted access.
●
Product information : Shows the current system's information.
– Model : Shows the model name of the product.
– Software version : The software version of the product currently being used is displayed. You can check the
software version and upgrade to the latest version.
– MAC address : Shows the Mac address of the product.
– RAID version : Shows the RAID version for products that support RAID.
– AI version : Shows the AI version of products that support AI.
– UWA version: Shows the UWA version of the product.
●
S/W Upgrade : Updates the Recorder's software up to date.
– If hard disk is unavailable or not properly connected, the software upgrades do not appear.
– Press the &lt;
&gt; buttons to search for the software in the USB or on the network.
– When the updating is done, it automatically restarts. Make sure to not turn off the power during upgrade.
●
Auto firmware update: When the network is connected to a recorder, you can receive new firmware
notifications. After selecting the setting you want, click &lt;Apply&gt;.
– Enable update notification : You will get a notification when there is new firmware.
– Auto updates : It checks if there is new firmware on the set date, day, or time, and automatically updates if
there is one.
– Disable update notification : It does not check for the presence of new firmware.
●
Auto update schedule: It activates when you select &lt;Auto updates&gt; in the &lt;Auto firmware update&gt;.
Select the date, day, or time to automatically update when new firmware is available.
●
Device name : You can enter a device name for your product. To differentiate multiple recorders in VMS, Device
Manager, etc., it is recommended to enter a different device name for each device.
￭ The system information displayed may differ depending on the recorder model.
82_ setup
2. When the recognized device appears, select &lt;Upgrade&gt;.
￭ If you connect a device in the upgrade menu window, you can press the &lt; &gt; button to search for available software.
￭ If there is an upgraded version on the network, a popup window will appear.
￭ &lt;Upgrade&gt; will be activated only when there is a higher version than the current software version.
3. In the &lt;Software upgrade&gt; window, select &lt;OK&gt;.
￭ While updating, it shows the progress.
4. When the updating is done, it automatically restarts.
Do not turn the power off until it finishes restarting.
￭ If “Upgrade Failed” appears, retry from the step 2. When you experience continued failure, consult the service center for assistance.
Settings
●
You can export the information set in the recorder to a storage device and apply the same information to other
recorders.
Power down : If the power is off, the first alarm is generated. Select the &lt;Use the alarm output no. 1 when the
device power is off&gt; check box and click &lt;Apply&gt; to clear all alarms set for alarm output 1, and then selecting
alarm 1 with another alarm out will not be possible.
￭ This function is provided only for products that support alarm output.
￭ If that function is set, the first alarm-out checkbox and all alarms in the alarm setup screen are deactivated, to Off.
Setup &gt; System &gt; System management &gt; Settings
storage device.
Log
You can check the log information related to system, events, and export.
Checking the system log
System Log shows log and timestamp on every system start up, system shutdown, and changes on system
settings.
●
Storage device : Shows the connected storage device.
– Press the &lt;
Setup &gt; System &gt; Log &gt; System log
&gt; button to view the list of storage devices.
– If you click &lt;Format&gt;, the format confirmation window will appear. Click &lt;Yes&gt; to format the selected
storage device.
●
Recorder ➡ USB : Save the information set in the recorder to a storage device.
– If you select &lt;Export&gt;, a confirmation window will appear. If you select &lt;OK&gt;, the recorder information will
be saved as a file.
●
USB ➡ Recorder : Apply the setting information stored in the storage device to the recorder.
– If you select the exclusion setting, you can import all information but the selected information.
– If you select &lt;Import&gt;, you can recall the setting information stored in the storage device. Select &lt;OK&gt; to
apply the loaded information to the recorder.
●
●
￭ The &lt;Export&gt; and &lt;Import&gt; settings can be used in the same software version only.
Factory default : Resets the product to its factory default settings. However, logs won't be reset. Anything
selected under Exclusion Setting won't be part of the factory reset.
A confirmation pop-up will appear when you press the &lt;Reset&gt; button. Select the &lt;OK&gt; button to reset the
selected items.
Camera registration method : Set the camera registration method. This function is only available for products
that support PoE. For products that support PoE, refer to the &quot;Functions Supported by Model&quot; page.
– Enable PnP mode: Cameras connected to the PoE port of the product will automatically be registered for
each channel in order of port number.
￭ When the camera resets to factory defaults, it defaults to the ID and password set in the &quot;Setup &gt; Camera &gt; Camera password&quot; menu.
If the camera ID and password are not set, the recorder ID and password will be set automatically.
●
Search date : Click the Calendar icon to display the calendar window, or use the direction buttons to specify the
search period of the system log.
●
Search : Specify the date and press this button to display the search result in the log list.
●
CH : Select a channel to search.
●
Log type : When there are too many logs, you can display logs of the desired format by selecting the type.
Select the desired type and click &lt;Apply&gt;.
●
First page/Last page : Move to the first/last page when there are many search results.
●
Export : Save all the logged information recorded in the Recorder into the storage device.
￭ If the camera's ID and password have already been set, the information that matches the ID and password set in the &quot;Setup &gt; Camera &gt; Camera
password&quot; menu will be registered (up to 3 sets).
￭ You may change the passwords of registered cameras all at once in the &quot;Setup &gt; Camera &gt; Camera password&quot; menu.
￭ If manual mode is used, you can register cameras connected to the recorder’s PoE port and cameras connected to a separate switch in the &lt;Channel
setup&gt; menu. For more details on camera registration, see the &quot;Setup &gt; Setting the Camera &gt; Setting the Channel” page in the Table of
Contents.
English _83
• setup
￭ If you export setup information, then the data will be saved as a file in the recorder folder of your storage device.
￭ If you want to import setup information, you have to first make sure that the setup information file is located in the recorder folder of the
setup
Checking the event log
Checking the export log
You can search recorded events including alarms, camera events and video loss.
It also shows the log and its timestamp.
You can search the user who performed the export and the execution time and details (time, channel, device, file
type).
Setup &gt; System &gt; Log &gt; Event log
Setup &gt; System &gt; Log &gt; Export log
●
Search date : Select the date to search the event log by using the calendar window that appears when the
calendar icon is selected or by using the arrow buttons.
●
Search date : Select the date to search the export log by using the calendar window that appears when the
calendar icon is selected or by using the arrow buttons.
●
Search : Specify the date and press this button to display the search result in the log list.
●
Search : Specify the date and press this button to display the search result in the log list.
●
CH : Select a channel to search.
●
First Page/Last Page : Move to the first/last page when there are many search results.
●
Log type : When there are too many logs, you can display logs of the desired format by selecting the type.
Select the desired type and click &lt;Apply&gt;.
●
First page/Last page : Move to the first/last page when there are many search results.
●
Export : Save all the logged information recorded in the Recorder into the storage device.
84_ setup
starting web viewer
What is Web Viewer?
Connecting Web Viewer
Web Viewer is a software program with which the operator can access a remote Recorder for real-time monitoring, PTZ
control (if configured) or search.
1. Open your web browser and type the IP address or URL of Recorder into the URL address box.
2. A user with the admin permissions should provide the admin ID and password.
A registered user should provide the user ID and password.
• starting web viewer
NETWORK
Network Camera
NETWORK
Recorder
Remote PC
Product Features
●
Remote connection using the browser
●
PTZ camera control enabled
●
Split mode supported
– 2-split vertical, 2-split horizontal, 3-split, 4-split, 6-split, 1+5-split, 1+7-split, 9-split
￭ Depending on the number of channels supported by the product, the number of screen split modes may vary.
●
Takes a screenshot and saves images in PNG format
●
Record video in AVI format-compatible with popular media players. (The integrated codec is needed)
3. After you log in, the Live Viewer main screen appears.
￭ All settings are applied according to the Recorder settings.
￭ If you change the web port when connecting to the Webviewer, you may fail to access since the applicable port is blocked. In this case, change the port
to a different port.
￭ Please change your password every three months to safely protect personal information and to prevent the damage of the information theft. Please,
take note that it's a user's responsibility for the security and any other problems caused by mismanaging a password.
￭ It allow s up to 10 simultaneous access including the admin and general users.
￭ Password of the admin and general users can be changed in &lt;User&gt; menu of the Recorder.
￭ Normal users should have set &lt;Web viewer&gt; under &lt;Remote access restriction&gt; to Use before connecting to the Web Viewer.
For details, refer to the &quot;Setup &gt; Setting the System &gt; User” page in the Table of Contents.
￭ All settings are applied according to the Recorder settings.
System Requirements
The following lists the minimum suggested hardware and operating system requirements needed to run the Web
Viewer.
●
Use the browser recommended by the OS.
Ex.) Microsoft recommended browser: Microsoft Edge
●
Supported browsers : Chrome, Edge, and Safari
●
Supported OS : Works on all of the Windows, Linux, and OS X environments given the platform-independent
nature of the web.
●
Tested environments : Tested and certified to run on Windows&reg; 10 with Edge 91, Google Chrome™ 91 and Intel&reg;
Core™ i7-7700 processor 3.60 Ghz with NVIDIA&reg; GeForce&reg; GTX™ 1050 or Intel™ HD Graphics 630.
●
Performance restrictions : The performance of users' CPU/GPU may impact the video playback performance of
the web viewer. The video quality may decrease depending on the settings, such as high resolution or transfer
bandwidth, when playing H.265 video in Chrome.
English _85
starting web viewer
Set the Recorder Password
2. Set the video recording method on the &lt;Storage&gt; screen, and then click &lt;Next&gt;.
After factory reset, the password must be set for the recorder to access the web viewer.
Enter the password of the admin account, and click &lt;Login&gt;.
￭ Click &lt;
●
Distributed mode : This function is only available for products that support distributed recording.
&lt;Distributed mode&gt; can be selected when there are two or more hard disks. This mode distributes the data and
saves it after the hard disk is formatted.
●
RAID mode: This function is only available for products that support RAID.
&lt;RAID mode&gt; saves data by configuring the hard disk in the RAID format.
●
Single group mode : Saves data on one hard disk. If the hard disk is recognized as an unusable hard disk in the
recorder, the data can be saved after formatting the hard disk.
&gt; to view the basic guide for setting a password. Refer to the password setup rules.
Installation Wizard
As shown below, proceed through each step of the &lt;Installation wizard&gt;.
Install Wizard can only be accessed at factory reset. If you do not want to proceed, click &lt;Exit&gt;.
￭ When you complete installation using the install wizard on your recorder, the install wizard will not appear on your web viewer.
3. Set the camera password in factory reset on the &lt;Camera ID/PW&gt; screen.
If ID/PW is already set in the camera, register the ID/PW and click &lt;Next&gt;.
1. In the &lt;Language&gt; screen, select the language and press the &lt;Next&gt; button.
￭ When the password is in factory reset, it can be changed and managed in a batch.
￭ Up to 3 sets of camera ID with password and password can be registered.
￭ You may change the passwords of registered cameras all at once in the &quot;Setup &gt; Camera &gt; Camera password&quot; menu.
￭ You cannot change the password for cameras registered with ONVIF and RTSP.
86_ starting web viewer
4. Set the network connection type and the connection environment on the &lt;Network&gt; screen, and then click the
&lt;Next&gt; button.
7. On the &lt;Easy connect&gt; screen, a remote user can network a recorder in a dynamic IP system.
Click &lt;Enable&gt; to test the connection to see if the current recorder can be connected remotely. When the
connection is successful, a QR code is created.
To connect a recorder via a viewer, select the viewer you want to use. You can check the connection method of the
selected viewer in the popup window.
• starting web viewer
￭ For details on network settings, refer to the &quot;Getting Started &gt; Installation wizard&quot; page in the Table of Contents.
5. Set the daylight saving time on the &lt;Time zone&gt; screen, and then click &lt;Next&gt;.
￭ It connects to Wisenet DDNS first. If it does not connect to DDNS, it automatically connects to P2P.
8. Click the &lt;Next&gt; button to complete the installation wizard.
Camera Setup
When the installation wizard closes, the camera setup screen will automatically appear.
Based on the registered camera's record profile information, you can check the total bandwidth, expected space, and
expected days.
You can change camera setup and the record schedule, and apply the same settings to other channels.
For details, refer to the &quot;Getting Started &gt; Camera Setup&quot; page of the table of contents.
6. To modify the date and time on the &lt;Date &amp; Time&gt; screen, select the &lt;Modify&gt; check box.
Set the date and time, and then click &lt;Next&gt;.
￭ The camera setup screen is also displayed when registering a camera for the first time in the &quot;Setup &gt; Camera &gt; Channel setup&quot; menu.
English _87
live viewer
You can check the video from camera registered in the Recorder connected from a remote PC. Also, you can adjust the
camera and check the network transfer status.
Menu
PTZ Control
Screen Layout of the Live Viewer
Description
Controls the connected PTZ camera.
Saves the video saved in the set time of the selected channel in PC in AVI format.
Clears the alarm in the event list and stops the alarm/beep sound for the system status when it is emitted.
Enables the Manual recording function of the recorder.
Displays the information on the OSD screen in the video window.
Shows the selected Channel Information.
Shows the status of all cameras connected to the recorder.
Sets the split screen of the video window.
Removes all screens from the video window.
Shows the video in actual proportions.
It changes to full screen from the current Split Mode.
To exit full screen, press the ESC key on your keyboard.
Menu
Menu
Click each menu to go to the corresponding menu screen.
●
List/Event
￭ MAC Safari does not support full screen.
Description
●
●
Video window
List : Select to check the camera list.
Displays the IP address and mutual authentication status of the viewer receiving the video from the recorder.
Event : Select to check the event list
●
: The &lt;
&gt; icon is displayed when you mouse over the camera list. Click the icon to go to the camera web page.
To go to the camera webpage, you must have the right to set channels, profiles, and events, and set &lt;Video&gt; to &lt;On&gt;
in the &quot;Setup &gt; Camera &gt; Channel setup&quot; menu.
Camera list
The list of cameras registered in the recorder is displayed.
Event list
Shows a list of events that occurred on the camera.
Layout list
Displays the default layout and a list of created layouts.
Shows the video of the camera connected to the recorder.
●
: Mutual authentication connection using WISENET device certificates
: Mutual authentication connection without WISENET device certificate
●
– : Connection without mutual authentication
●
No viewer connected : Displayed when there is no viewer connected to the recorder.
The ID of the connected user is displayed.
You are directly connected to the Hanwha Techwin homepage (www.hanwha-security.com).
Changes the color theme of Web Viewer.
System status display
88_ live viewer
Displays the status of the system, hard disk, and network.
Checking the System Status
Checking Camera List
The icon at the top of the screen indicates the status of the system.
Displays the camera type, status, and name registered in the recorder.
Name
Description
Live &gt; List
Displayed when a problem occurs with the pan or recording status.
• live viewer
Displayed when an error occurs in the power supply.
Displayed when the amount of input data by channel exceeds the set amount of data limit.
Displayed when the hard disk is full during recording and the recording capacity is insufficient.
Displayed when the hard disk does not exist or needs to be replaced.
Name
Displayed when there is an abnormality in RAID or cannot be used.
Displayed when RAID is being rebuilt.
Channel information
￭ Only provided for products that support RAID.
Camera type
Displays a PTZ camera.
Displayed when the capacity of the built-in battery in the recorder is insufficient. After replacing the battery, set the system time again.
Displayed when network overload occurs.
￭ It occurs in case of excessive CPU load because the reception performance is exceeded. It disappears when you modify the Delete Camera
or Set Camera to reduce the data rate.
￭ Limit the number of users remotely monitored by Web Viewer or VMS, or control the number of channels played by remote or recorder.
Displayed if the server has firmware to update.
Checking User ID
Displays the user ID and authority for the user connected to Web Viewer.
Click &lt;Logout&gt; to log out the logged-in user.
Displays channel information (channel number, video window assignment, and color indication).
Displays a normal camera.
Displayed when an error occurs in the iSCSI device connection.
￭ Only provided for products that support iSCSI.
Description
Camera status
Camera name
Displays the camera error status.
Displays the name set for the camera.
￭ If a camera connection error occurs, it is disabled in the list.
￭ The camera status display information changes according to the network connection status and settings.
￭ For multichannel cameras registered with the Wisenet protocol, the channel information will be displayed under the model name of the multichannel
camera.
￭ In case of multichannel cameras, only one main channel can be registered for recording.
Subchannels in which recording is not required do not need to be registered on the recorder, as they can be monitored real time. However, recording,
event reception, or camera settings are not available.
￭ If you are logged in with an admin account, the authority setting window will not be displayed.
English _89
live viewer
Checking the All Camera Status
Network Status
You can check the status of all cameras connected to the recorder.
Click the &lt;
&gt; button, followed by the &lt;Network&gt; tab.
You can check the status of network bandwidth currently being received/transmitted.
Live Status
Click the &lt;
channel.
&gt; button. You can check the status and transmission information of the camera connected to each
￭ To change the profile setup, click the &lt;Camera setup&gt; button. For details on how to set up the profile, refer to the &quot;Setup &gt; Setting the Camera &gt;
Setting the Profiles” page in the Table of Contents.
￭ Each product supports a different number of network ports.
PoE Status
Click the &lt;
Record Status
Click the &lt;
&gt; button and then click &lt;PoE&gt;.
You can check the current PoE status of each port.
&gt; button, followed by the &lt;Record&gt; tab.
You can check the profile, record type, frame rate (Input/Record), and bit rate (Limit/Input/Record) for each
channel.
Max&gt; to check the current recording status and maximum recording setting value.
￭ Use &lt;Current
￭ To change the profile setup, click the &lt;Record Setup&gt; button.
￭ This function is only available for products that support PoE.
90_ live viewer
Changing the Pattern of Split Screen
Changing Overall Channel Aspect Ratio
Click the &lt;
Video screen ratio for all channels can be changed in live split screen mode.
&gt; button and select the desired split screen.
The selected split screen is applied to the video window.
Click &lt;
&gt; at the bottom of the screen. It changes to the actual proportion of the video.
• live viewer
If you want to go back to the previous screen ratio, click &lt;
&gt; again.
English _91
live viewer
Full Screen Mode
Setting up the Live Layout
You can change to full screen mode, which has no top/bottom/left/right areas of the live screen.
This section outlines how to select a series of channels based on their purpose/accessibility and monitor them in a
single layout.
Click &lt;
&gt; at the bottom of the screen.
Live &gt; List
Check Layout List
To exit the full screen, press the ESC key on the keyboard or click &lt;
General mode
&gt; at the bottom of the full screen mode.
Full screen mode
●
: Create a new layout.
●
: Change the channel or name of the layout.
●
: Save the changed layout.
●
: Delete the added layout.
●
/
: Open or close the layout list.
Add Layout and Set Name
1. Click the &lt;
&gt; button.
2. Set the name of the layout.
3. Double-click a channel to display on the layout screen from the camera list.
4. Click &lt;
&gt; to save the set layout.
￭ The default layout of the live viewer consists of a 4-split screen.
￭ Each layout is saved separately by the user.
92_ live viewer
Change of Layout Channel and Name
Real-Time Event Monitoring
1. Click &lt;
Real-time events that occurred on the camera can be checked in the live video window and event list.
&gt; after selecting a layout.
2. Add or delete channels or rename layouts.
3. Click &lt;
&gt; to save the changed settings.
Click &lt;
&gt; after selecting the layout to delete.
or camera.
￭ Live event monitoring can receive data on only one channel and data can be received only from the camera currently being monitored in live.
Live &gt; Event
Check Event List
Click &lt;
Event&gt; on the left side of the live screen to display the real-time event list.
￭ When new events occur, the list of events will be updated accordingly.
￭ The specified channels and events are displayed in the list according to the event rule setup.
For details, refer to the &quot;Setup &gt; Setting the Event &gt; Event rule setup&quot; page in the Table of Contents.
●
: Browses for the event by the desired condition.
●
/
: Open or close the event list.
￭ When an alarm output occurs, if the event recording is set and the pre-event time and post-event time are set, the event recording is executed
before or after the event according to the set recording method. For more information about event recording settings, refer to the &quot;Setup &gt;
Setting the Recording &gt; Record setup&quot; page in the Table of Contents.
￭ The video may be delayed depending on the network conditions.
￭ The event output can be delayed as the transfer of the alarm event from the network camera takes time.
English _93
• live viewer
Delete Layout
￭ AI events are only available for products that support AI.
￭ AI events are displayed only after setting event rules. AI event search may have different settings and operation specifications depending on the recorder
live viewer
Event Search
Event Instant Viewer
You can browse events by camera and event type.
To search for a specific event, click &lt;
&gt; to select the event type and camera to browse.
Event filter
Displays only selected events in the event list.
Select an event to check from the event list, and click &lt;
occurred.
&gt; to play the recorded video at the time the event
￭ Instant viewer can play an event video for 1 minute.
￭ For AI events, the best shot and details of the event that occurred are displayed.
￭ AI event recognition may have different settings and operation specifications depending on the recorder model or camera.
￭ To see AI events, set any of the following options as necessary : See the relevant page for detailed setup method.
–– Setup &gt; Event &gt; AI engine
–– Setup &gt; Event &gt; Event setup &gt; Object
–– Setup &gt; Event &gt; Event setup &gt; AI recognition
–– Setup &gt; Event &gt; Event setup &gt; Mask
–– Setup &gt; Event &gt; Event setup &gt; IVA
–– Setup &gt; Event &gt; Event rule setup
AI event
●
Common event : Searches for event types that have occurred in general cameras such as motion detection and
IVA.
●
AI event : Searches for AI event types such as face, person, and vehicle.
Common event
￭ AI events are only activated when an AI camera is connected.
￭ AI events are displayed only after setting event rules. For details, refer to the &quot;Setup &gt; Setting the Event &gt; Event rule setup&quot; page in the Table of
Contents.
Camera filter
Displays events for the selected camera only.
●
/
: The video is played/paused.
●
: Go to the search menu screen.
●
: Instant Viewer playback ends.
Stop Alarm Output
When an event occurs, an alarm can occur. Click &lt;
necessary.
&gt; at the bottom of the screen to stop the alarm output if
For details, refer to the &quot;Setup &gt; Setting the Event &gt; Event rule setup&quot; page in the Table of Contents.
94_ live viewer
Live Screen Menu
Camera Video Control
After selecting the desired channel on the split mode, roll the mouse cursor over the screen to see the live screen menu.
By using the function icon in the video window, you can easily enable functions such as screenshot, video rotation, and
PTZ control.
The live screen menu appears differently depending on the recorder operation status or the type of the registered
camera.
￭ Each function may be restricted depending on the type of camera and the user's authority.
RECREC
RECREC
RECREC REC
REC
90 90
90 90
90
90
If the event action for &lt;Manual trigger&gt; is set for the selected channel in the &quot;Setup &gt; Event &gt; Event rule
setup&quot; menu, the event rule name will be displayed when you hover the mouse over &lt;
&gt;. Click &lt;
&gt; to
activate the set event.
90 90 90 90 90
RECREC
RECREC
REC
90 90 90 90 90
RECREC REC
90 90
90 90 90 90 90
90
Manual trigger 1
RECREC
RECREC
RECREC REC
REC
Menu
90 90
90
90 90 90 90 90
Description
RECREC
RECREC
REC 90 90 90 90 90
If the event action for &lt;Manual trigger&gt; is set for the selected channel, the event rule name is
displayed when you hover the mouse over &lt;
&gt;. Click &lt;
&gt; to activate the set event.
Capture
You can take a screenshot of the selected channel.
Manual trigger
RECREC REC
90 90
90 90
90
90
90 90 90 90 90
PC REC
Instant viewer
Capture
RECREC REC
90 90
90
Select a channel to capture
and click the &lt;
RECvideo
RECREC
REC
REC 90 90 90 90 90
&gt; button.
The captured image is saved as .png file in the download folder.
Images can be saved on a PC.
During monitoring, you can rewind 1 minute before playback.
90 90
PC Recording
90
90 90 90 90 90
You can record video on your PC while monitoring.
Microphone
Turns the microphone on or off on your PC.
1. Select the desired channel and click the &lt;
PTZ control
If the network camera connected to the selected channel supports the PTZ function, it changes to the
PTZ control mode.
&gt; button.
2. To end the PC recording, click the &lt;
The recording ends, and the recorded video is saved as .avi file in the download folder.
Audio
Image rotation
Channel aspect ratio
&gt; button to start PC recording.
Turns the audio on or off when the audio is connected.
Rotates the video to display.
Shows the video in actual proportions.
English _95
• live viewer
RECREC
RECREC
REC
RECREC REC
Manual Trigger
live viewer
Instant Viewer
PTZ Mode
During monitoring, you can rewind 1 minute before playback.
You can run PTZ control of the selected channel.
Select the desired channel and click &lt;
The Instant Viewer screen appears.
Select the desired channel and click &lt;
&gt;.
&gt;.
Enters the PTZ control mode.
￭ Depending on the camera, the PTZ control function and speed may be different.
REC
REC
90 90
REC
REC
●
/
: The video is played/paused.
●
: Moves to the playback screen.
●
: Instant Viewer playback ends.
REC
: The PTZ mode is closed.
●
: Captures video of the current state.
: Go to the instant90viewer.
REC
REC
&gt;.
90 90
: Click the Digital zoom icon and use the mouse wheel to zoom in or out on the video.
Digital zoom ends when the video screen is reduced to the original size.
●
90 90
You can turn the microphone of the selected channel on or off in the live screen.
Select the desired channel and click &lt;
90
●
REC●
Microphone Output
90 90
Adjusting the Camera Direction
When you rolls over the mouse to &lt;
&gt;, the 8-way key appears, and when the mouse leaves the area of the
direction key, the direction key disappears. You can fine-tune the camera direction by clicking the 8-direction key
REC
90
once. Keep
clicking the arrow keys to move in the desired direction and release the mouse to stop.
To quickly adjust the direction of the camera, click &lt;
&gt; and drag. The screen moves quickly in the desired
direction. You can adjust the screen movement speed according to the drag distance.
90
96_ live viewer
Zoom In
Channel Aspect Ratio
You can zoom in or out using the mouse wheel.
You can change the aspect ratio of each channel.
If you scroll up using the mouse wheel, the selected video screen is enlarged by 10%, and a thumbnail window is
displayed.
Select the desired channel and click &lt;
REC
It changes to the actual proportion of the video.
• live viewer
￭ Scrolling up/down using the mouse wheel will zoom in/out the video screen by 10%.
￭ Digital zoom ends when the video screen is reduced to the original size.
￭ In PTZ mode, click the &lt; &gt; button to run digital zoom.
&gt;.
90
REC
90
RECREC
90
90
Audio
REC
REC
90
90
You can turn the sound on/off corresponding to the channel in Live mode.
Select the desired channel and click &lt;
&gt;.
Audio output can only be turned on90 in one channel. The audio output of other channels will be automatically
turned off.
90
￭ If you have configured the audio output settings properly but the audio or voice is not output, check if the connected network camera supports
the sound signal and if you have configured the sound settings as appropriate.
The sound icon can be displayed if the sound signal fails to output from noise.
￭ Only the channel where &lt;Audio&gt; is set to &lt;On&gt; in “Setup &gt; Camera &gt; Channel setup” displays the audio icon (
you can use to turn the sound on/off.
) in Live mode that
Image Rotation
You can rotate the live video screen.
Select the desired channel and click &lt;
&gt;.
Each click of the button will rotate the video 90 degrees clockwise.
English _97
live viewer
PTZ Control
Using Digital PTZ (D-PTZ) function
PTZ Control Menu
1. Register a camera that supports the D-PTZ profile.
If the connected network camera is a PTZ camera, the &lt;
camera channel is selected, you can control the PTZ.
&gt; icon is displayed in the camera list. When the
￭ In cameras that support the D-PTZ profile, you can use the D-PTZ function.
2. Both cameras that support general PTZ and cameras that support D-PTZ can control the live image using
some of the &lt;PTZ control&gt; function menus.
￭ For more information about the supported functions, please refer to the camera manual.
Preset
Preset is a set of saved data specifying the locations of a PTZ camera. A single PTZ camera can save up to 300
locations.
To add a preset
1. Select the desired channel and click &lt;
￭ The PTZ control screen appears.
&gt;.
2. Use the arrow keys to adjust the camera to the point.
3. Click &lt;
Name
Description
Zoom out/Zoom in
98_ live viewer
4. If you click &lt;Set&gt;, the &lt;Preset setup&gt; window will appear.
Activate the Zoom operation of the PTZ camera.
Near/Far
You can adjust the focus manually.
Auto focus
You can adjust the focus automatically.
Preset
Set the preset position to move the camera, and then select the desired preset to move to the set
position.
Swing
&gt;.
Swing is a monitoring function that moves between two preset points and enables you to trace the
motion.
Group
The group function enables you to group various presets before calling them in sequence.
Tour
Monitor all the groups created by a user in turn.
Trace
Tracking remembers the trace of movements that you instructed and reproduces it for your
reference.
Set
The preset you set is saved and displayed in the list.
Delete
Deletes the selected preset list.
Preset List
Shows a list of saved presets.
5. Click &lt;
&gt; to select the Preset Order to set.
6. Enter the Preset name.
7. Click &lt;Save&gt;.
The preset setting will be saved.
￭ If you replace a camera that saves your preset settings with a different one, you must configure the preset settings again.
To delete a registered preset
Exporting Video
1. Click &lt;
You can export the recorded video by manually inputting the desired channel, date, and time.
&gt;.
2. Select the preset to delete, and click &lt;Delete&gt;.
1. Click the &lt;
&gt; button.
3. &lt;Delete preset&gt; window will appear, and click &lt;OK&gt;.
The selected preset will be deleted.
• live viewer
Running Preset
1. Click &lt;
&gt;.
2. Double-click the preset you want to run from the list.
The camera lens moves to the set position.
Running Swing (auto pan), Group (scan), Tour, or Trace (pattern)
The running method of each function is the same as the preset operation method. For details on how to use it,
refer to the camera's user manual.
￭ Depending on the camera's capabilities, only some features may be available.
2. Select a layout to export and select the desired channel.
3. Set the start date/time and end date/time.
￭ After setting whether to enable DST or not, select the overlap. It will be displayed when there is overlapped data in one channel by changing the time or time
zone at the selected time.
4. Enter a file name to save, and then click the &lt;OK&gt; button.
5. When the export is complete, a confirmation window appears.
￭ The exported video is saved as .avi file in the download folder.
English _99
search viewer
You can search and play the recorded video stored in the recorder by connecting the recorder remotely.
Time Search
Screen Layout of the Search Viewer
You can search the recorded data by the desired date and time conditions.
￭ The time displayed will be based on the time zone and daylight saving time (DST) applied time zone, so it may be displayed differently depending on
whether the data time zone recorded at the same time and daylight saving time (DST) is applied.
1. Select &lt;Time search&gt; in the &lt;Search&gt; menu.
2. Select a channel to search.
Name
Description
Menu
Search menu tab
3. Select the year and month to search.
Dates with data will be shown in orange and current dates will be shown in orange circles.
4. Select a date to search from the calendar.
The recorded video for that day will be played from the beginning, and the data will be displayed in the timeline.
Click each menu to go to the corresponding menu screen.
Click the menu tab to display the detailed search menu. Click Search menu to go to the corresponding Search screen.
Search conditions
You can set various search conditions, such as date/time/event.
Search results
Displays search results.
●
●
– Red : Event recording video
/
Exports search results to an .avi file.
￭ In the &lt;Text search&gt; results, you can also click &lt;
&gt; to export to a .csv file.
Displays the search results as a list or thumbnail.
￭ Click &lt;Reset&gt; to initialize the search conditions and results.
￭ When you click Playback ( ), the video will be played in an instant viewer.
￭ You can specify a bookmark by clicking the bookmark ( ) in the search results list. You can check the specified video in the bookmark search menu.
￭ If the search results are in multiple pages, you can click / to go to the previous/next page. Or, you can click the current page number and enter the
page you want to move to.
100_ search viewer
The displayed color differs depending on the type of recording data.
– Light green : Normal recording video
●
/
Click &lt;Today&gt; to search for today's date. Today’s date will be selected.
●
: You can filter the event items to view the time line.
Overlapped : You may check the timeline by setting the overlapping section caused by time change.
Text Search
You can search for various events by channel.
You can search the data input to the POS device connected to the recorder.
1. Select &lt;Event search&gt; in the &lt;Search&gt; menu.
1. Select &lt; Text search&gt; in the &lt;Search&gt; menu.
2. Select a channel to search.
2. Select the date and time to search.
3. Select a date and time to search.
3. Set the event keywords and search condition.
• search viewer
Event Search
4. Select an event type.
●
Event type options may vary depending on the camera model.
5. Select the overlap.
●
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the
selected time.
6. Click the &lt;Search&gt; button.
The search results list will be displayed.
￭ To stop the search, click &lt;Stop&gt; in the search pop-up window. You can check the search results up until now.
●
CH : Displays the channel where the event occurred.
●
Camera name : Displays the camera name.
●
Event : Displays the event type of the recorded video.
●
Time : Displays the start time and end time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark for the recorded video.
●
Event keyword : You can search for text with preset event keywords. For details, refer to the &quot;Setup &gt; Setting the
Device &gt; Text&quot; page in the Table of Contents.
●
Text search keyword : Enter the text you want to search.
●
Match with case sensitivity : Searches are case-sensitive when checking.
●
Match whole words : Searches for data that exactly matches the characters entered.
4. Select the overlap.
●
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the
selected time.
5. Click the &lt;Search&gt; button.
The search results list will be displayed.
￭ To stop the search, click &lt;Stop&gt; in the search pop-up window. You can check the search results up until now.
●
Device: Displays the name of the POS device connected to the recorder.
●
Keyword: Displays the searched text.
●
CH : Displays the channel where the event occurred.
●
Time: Displays the start time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark for the recorded video.
English _101
search viewer
Bookmark Search
Search Results Export
You can search for bookmarked data.
Search results of events, texts and bookmarks can be exported to a file.
Example) Bookmark search result export
1. Click &lt;
&gt; in the search results list.
1. Select &lt;Bookmark Search&gt; in the &lt;Search&gt; menu.
2. Select a channel to search.
3. Select the date and time to search.
4. Click the &lt;Search&gt; button.
The search results list will be displayed.
●
Bookmark name: Displays the bookmark name you set.
●
Event: Displays the event type of the recorded video.
●
CH: Displays the recorded channel.
●
Time: Displays the start time and end time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark: Displays whether bookmarks are specified.
￭ Bookmarked images will be stored without being overwritten during repeated recording. However, when the automatic deletion is set, it will be deleted
according to the set period.
￭ When the bookmark is released, the video will not be saved. If necessary, before releasing the bookmark, export the video.
￭ Up to 100 bookmarks can be specified.
102_ search viewer
2. Select the desired list and click &lt;OK&gt;.
￭ The exported video is saved as .avi file in the download folder.
￭ In the &lt;Text search&gt; results, you can also click &lt;
&gt; to export to a .csv file.
AI search viewer
If there is AI data recorded by the camera, you can search for images in various conditions such as people, faces, and
vehicles.
￭ This function is not supported in some models.
￭ For products that support the AI search function, refer to the &quot;Functions Supported by Model&quot; page.
Person Search
In the recorded data, you can search for a person by any condition you want, such as gender, top/bottom color.
• AI search viewer
Screen Layout of the AI Search Viewer
1. Select &lt;Person search&gt; in the &lt;AI search&gt; menu.
2. Select a channel to search.
3. Select the date and time to search.
4. Select a detailed search option.
●
Name
Menu
Description
Click each menu to go to the corresponding menu screen.
Search menu tab
Click the menu tab to display the detailed search menu. Click Search menu to go to the corresponding Search screen.
Search conditions
You can set various search conditions, such as date/time/gender.
Search results
Displays search results
Exports search results to a file.
Displays the search results as a list or thumbnail.
￭ Click &lt;Reset&gt; to initialize the search conditions and results.
￭ You can specify a bookmark by clicking the bookmark ( ) in the search results list. You can check the specified video in the bookmark search menu.
Person search options : Gender, Clothing-Top color, Clothing-Bottoms color, Bag
￭ Click the option to display the option selection window. Select the desired search option.
￭ If no details are set, all conditions will be selected and searched.
5. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
6. Click the &lt;Search&gt; button.
The search results list will be displayed.
￭ To stop the search, click &lt;Stop&gt; in the search pop-up window. You can check the search results up until now.
●
CH : Displays the recorded channel.
●
Camera name : Displays the camera name.
●
Attribute : Displays the recognized search result attributes.
●
Time : Displays the start time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
7. Click &lt;
&gt; in the search list to display the instant viewer.
8. Click &lt;
&gt; to go to the playback screen.
English _103
AI search viewer
Face Search
Vehicle Search
From the recorded data, you can search faces according to your desired conditions such as gender and age.
You can search the vehicle by setting the vehicle type and color conditions from the recorded data.
1. Select &lt;Face search&gt; in the &lt;AI search&gt; menu.
1. Select &lt;Vehicle search&gt; in the &lt;AI search&gt;menu.
2. Select a channel to search.
2. Select a channel to search.
3. Select the date and time to search.
3. Select the date and time to search.
4. Select a detailed search option.
4. Select a detailed search option.
●
Face search options : Gender, Age, Glasses, Mask
￭ Click the option to display the option selection window. Select the desired search option.
￭ If no details are set, all conditions will be selected and searched.
●
Vehicle search options : Type, Vehicle color
￭ Click the option to display the option selection window. Select the desired search option.
￭ If no details are set, all conditions will be selected and searched.
5. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
5. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
6. Click the &lt;Search&gt; button.
The search results list will be displayed.
6. Click the &lt;Search&gt; button.
The search results list will be displayed.
￭ To stop the search, click &lt;Stop&gt; in the search pop-up window. You can check the search results up until now.
●
CH : Displays the recorded channel.
●
￭ To stop the search, click &lt;Stop&gt; in the search pop-up window. You can check the search results up until now.
●
CH : Displays the recorded channel.
Camera name : Displays the camera name.
●
Camera name : Displays the camera name.
●
Attribute : Displays the recognized search result attributes.
●
Attribute : Displays the recognized search result attributes.
●
Time : Displays the start time of the recorded video.
●
Time : Displays the start time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
●
Bookmark : Specifies a bookmark to the recorded video.
7. Click &lt;
&gt; in the search list to display the instant viewer.
7. Click &lt;
&gt; in the search list to display the instant viewer.
8. Click &lt;
&gt; to go to the playback screen.
8. Click &lt;
&gt; to go to the playback screen.
104_ AI search viewer
LP Search
LPR Search
You can search for vehicle license plates from the recorded data.
You can search for the license plate number recognized in the recorded data.
￭ LPR search is only available on recorder models that support AI recognition.
• AI search viewer
1. Select &lt;LP search&gt; in the &lt;AI search&gt; menu.
2. Select a channel to search.
3. Select the date and time to search.
4. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
5. Click the &lt;Search&gt; button.
The search results list will be displayed.
￭ To stop the search, click &lt;Stop&gt; in the search pop-up window. You can check the search results up until now.
●
CH : Displays the recorded channel.
●
Camera name : Displays the camera name.
●
Time : Displays the start time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
6. Click &lt;
&gt; in the search list to display the instant viewer.
7. Click &lt;
&gt; to go to the playback screen.
1. Select &lt;LPR search&gt; in the &lt;AI search&gt; menu.
2. Select a channel to search.
3. Select the date and time to search.
4. Enter the license plate number to search.
￭ Click &lt; &gt; to see the search guide for license plate number.
￭ The option of license plate number entry field is only available on recorder models that support LPR search.
5. Select the overlap.
It will be displayed when there is overlapped data in one channel by changing the time or time zone at the selected
time.
6. Click the &lt;Search&gt; button.
The search results list will be displayed.
￭ To stop the search, click &lt;Stop&gt; in the search pop-up window. You can check the search results up until now.
●
CH : Displays the recorded channel.
●
Camera name : Displays the camera name.
●
LPR : Shows the identified license plate number.
●
Time : Displays the start time of the recorded video.
●
Playback : Plays the recorded video with an instant viewer.
●
Bookmark : Specifies a bookmark to the recorded video.
7. Click &lt;
&gt; in the search list to display the instant viewer.
8. Click &lt;
&gt; to go to the playback screen.
English _105
AI search viewer
Search Results Export
Search results such as people, faces, and vehicles can be exported to a file.
Example) Person search results export
1. Click &lt;
&gt; in the search results list.
2. Select the desired list and click &lt;OK&gt;.
￭ The exported video is saved as .avi file in the download folder.
106_ AI search viewer
play
Play Search Results
Export Video by Section Setup
You can play the recorded data and export the video you want during playback.
You can select the desired section from the time line or search list during video playing and export it to a file.
To Adjust the Time Line
1. Click the &lt;
&gt; button
2. Select the start and end points of the desired section in the time line with the mouse.
You can move the playback position and zoom the time line in and out.
• play
3. Click the &lt;
●
●
●
&gt; button.
Click the desired play position in the time line.
The playback start position will be moved.
￭ Click the start point on the left side of the time line to move the playback position to the start point of the first video.
￭ Place your mouse over the time line to see the corresponding thumbnail of the recorded video.
Click &lt;
&gt;, &lt;
&gt; to zoom in or out the time display magnification. When the time line is enlarged, a scroll
bar will appear at the bottom.
￭ You can use the mouse wheel over the time line to zoom in or out on the time scale.
￭ The time line magnification of the time line will be displayed at the top right of the time line.
To see the time line before or after zooming in, zoom in and drag the time line left or right.
4. Select a layout to export and select the desired channel.
5. Set the start date/time and end date/time.
6. Enter a file name to save, and then click the &lt;OK&gt; button.
7. When the export is complete, a confirmation window appears.
￭ While exporting, click the &lt;Stop&gt; button to stop the export.
English _107
play
Play Button Name and Function
Paused state
Playback state
Name
Description
Previous event
Go to the previous event video.
Previous frame
Moves backward to the key frame (I-frame).
Playback
Play the video.
Next frame
Moves forward one frame or more.
Next event
Go to the next event video.
Speed
Select the video playback speed.
Speed : x1/8, x1/4, x1/2, x1, x2, x4, x8, x16, x32, x64, x128, x256
It is used for reverse playback.
Fast backward
Pause
Speed : -x1/8, -x1/4, -x1/2, -x1, -x2, -x4, -x8, -x16, -x32, -x64, -x128, -x256
￭ Depending on the split screen, the maximum speed may be limited.
Pause the video.
It is used for forward playback.
Fast forward
108_ play
Speed : x1/8, x1/4, x1/2, x1, x2, x4, x8, x16, x32, x64, x128, x256
￭ Depending on the split screen, the maximum speed may be limited.
setup viewer
You can configure the Recorder settings remotely on the network.
Setting the Camera
Screen Layout of the Setup Viewer
You can check a list of cameras that are connected to the Recorder and configure the necessary settings.
For details, refer to the &quot;Setup &gt; Setting the Camera&quot; page in the Table of Contents.
Channel setup
￭ When you register a camera for the first time in the &quot;Setup &gt; Camera &gt; Channel setup&quot; menu, the camera setup screen will be displayed.
For details, refer to the &quot;Getting Started &gt; Camera Setup&quot; page of the table of contents.
Setup &gt; Camera &gt; Channel setup
Name
Menu
Description
Click each menu to go to the menu screen.
●
When you click the &lt;Upgrade&gt; button, you can check the camera’s version, upgrade version, and status and
upgrade it.
Top menu list
Configure the settings or select a parent item to change the existing settings.
Sub-menu list
Among the sub-menus of selected parent menu, select a desired item to set.
Camera setup
Detailed Menu
Click desired item's input field to change and enter a desired value.
You can change the video settings of network cameras registered for each channel by accessing the web viewer.
Apply
Apply the modified settings.
Revert
Revert to the settings used before the change.
Setup &gt; Camera &gt; Camera setup
English _109
• setup viewer
You can register a network camera for each channel and make a connection between them.
setup viewer
●
When you click the &lt;Camera webviewer&gt; button, a new camera web browser window is opened.
– This is not supported if the camera is connected to the RTSP protocol.
Profile Setup
You can set the profile for a network camera.
– This is not supported if the camera is connected to DDNS or a URL.
– It supports the version specified below or later for each Q/P/X series camera.
(QND-7010R series : 1.04, QND-7080R series : 1.02, QND-6010R series : 1.02,
QND-6070R series : 1.01, P series : 1.01)
Setup &gt; Camera &gt; Profile setup
– When you are connecting to the camera web page on a closed network, a camera that does not support the
universal web will not be able to output an image.
Record
You can set the recording profile for a network camera.
– The cam proxy port's default settings are automatically set in sequence as many as the number of channels
supported by Recorder. If you want to change the proxy port, then select the port setup menu.
– 4 channels (10001-10004), 8 channels (10001-10008), 16 channels (10001-10016),
32 channels (10001-10032), 64 channels (10001-10064)
Example) Defaults of cam proxy ports for each product
●
4-channel model : 10001-10004
●
8-channel model : 10001-10008
●
16-channel model : 10001-10016
●
32-channel model : 10001-10032
●
64-channel model : 10001-10064
– When connecting outside the closed network as shown in the figure, the port forwarding setting of the
camera proxy port is required for the router.
●
Click &lt; &gt; to change the profile settings. You can add or delete profiles, and change the settings of
&lt;Dewarping&gt;, &lt;WiseStream&gt;, and &lt;Dynamic GOV &amp; FPS&gt;.
Internet
Network Camera
Recorder
IP router
Remote PC
– If there are multiple Recorders within the closed network, each cam proxy port should be set using a
different port.
– If DDNS and Quick Connect are enabled, port forwarding will be automatically set.
– Chrome, Edge and Safari (Mac OS) browsers are supported.
110_ setup viewer
Live
You can change the live transfer settings of the network camera.
Remote
Setting the Recording
You can set the video profile transmitted to the network and the expansion monitor.
For details, refer to the &quot;Setup &gt; Setting the Recording&quot; page in the Table of Contents.
Record Schedule
If you set a recording schedule for a specific date and time, the recording will start at that specific time.
• setup viewer
Setup &gt; Record &gt; Record schedule
Camera Password
You can change the passwords of all registered cameras at once.
Setup &gt; Camera &gt; Camera password
Record Setup
Select a type of the normal/event recording frame rate for each channel.
Setup &gt; Record &gt; Record setup
English _111
setup viewer
Record Options
Setting the Event
You can set the hard disk recording option.
For details, refer to the &quot;Setup &gt; Setting the Event&quot; page in the Table of Contents.
￭ You can set the recording duration separately for each channel.
Setup &gt; Record &gt; Record options
AI engine
You can set whether or not to use AI events (object detection, AI recognition) and check the status of AI engine
usage.
￭ AI engine settings are only available on recorder models that support AI recognition.
Setup &gt; Event &gt; AI engine
Event Setup
You can set detailed settings for each channel's event detection mode.
Setup &gt; Event &gt; Event setup
Object detection
You can change the AI object detection event setup.
￭ The object detection function is displayed only when connected Wisenet AI camera.
112_ setup viewer
AI recognition
Motion detection
You can change the AI recognition event setup.
You can change the settings for motion detection events.
￭ Settings and operating specifications may differ depending on the recorder model and camera.
￭ Detailed video analysis can be set by accessing the Camera webviewer.
• setup viewer
Mask detection
IVA
You can change the mask detection event setup.
You can change the settings for Intelligent Video Analytics (IVA) events.
￭ Settings and operating specifications may differ depending on the recorder model and camera.
￭ Detailed video analysis can be set by accessing the Camera webviewer.
English _113
setup viewer
Tampering detection
Event Rule Setup
You can change the tampering detection event setup.
You can set the event trigger and action rule to output an alarm when an event occurs.
Setup &gt; Event &gt; Event rule setup
Video loss detection
You can change the video loss detection event setup.
Alarm Input
You can set the operation of the alarm sensor.
￭ This function is not supported in some models.
Setup &gt; Event &gt; Alarm input
114_ setup viewer
ONVIF Setup
Setting the Device
You can set the camera registered with the Onvif protocol.
You can check a list of devices that are connected to the Recorder and configure the necessary settings.
Setup &gt; Event &gt; ONVIF setup
For details, refer to the &quot;Setup &gt; Setting the Device&quot; page in the Table of Contents.
Storage Device
• setup viewer
You can check and change the settings related to the data storage device.
Setup &gt; Device &gt; Storage device
Management
You can check a storage device, amount of use, type of use and status of storage device.
Schedule
Whether to output an alarm can be scheduled according to the day and time.
The initial setting will be an event sync, and an alarm will be sent only when an event occurs.
Setup &gt; Event &gt; Schedule
●
ARB : Video that was not recorded due to disconnection from the camera can be backed up after the
connection with the camera is re-established.
Press the button and an &lt;Auto recovery backup (ARB)&gt; window is opened.
For details, refer to the &quot;Setup &gt; Setting the Device &gt; Storage Device&quot; page in the Table of Contents.
iSCSI
This function is only available for products that support iSCSI.
When connecting an iSCSI device to the recorder, you can search for the iSCSI device and connect and disconnect
it.
English _115
setup viewer
RAID
S.M.A.R.T
This function is only available for products that support RAID.
You can check the connection status and details of the hard disk mounted in the recorder.
You can set the RAID (Redundant Array of Independent Disks) mode.
Distributed recording
This function is only available for products that support distributed recording.
By allocating a certain portion of HDDs to each group, you can distribute the amount of recording for optimal
saving.
Monitor
You can set the information displayed on the monitor as well as the output system.
Setup &gt; Device &gt; Monitor
￭ If the screen does not work properly, see “Troubleshooting (FAQ)” in the Appendix.
￭ The Monitor Setup settings control the monitor connected to the Recorder.
￭ Video exceeding the resolution of 1080p will not be displayed from the secondary monitor.
116_ setup viewer
Text
Setting the Network
You can set the POS device text display and event text settings.
For details, refer to the &quot;Setup &gt; Setting the Network&quot; page in the Table of Contents.
Setup &gt; Device &gt; Text
IP &amp; Port
A remote user can access the Recorder via the network to check the current mode and the IP address.
Relevant values of a POS device connected to Recorder can be set.
Setup &gt; Network &gt; IP &amp; Port
• setup viewer
Device
IP address
Specify the network connection path.
Event
It is possible to set total amount conditions and keywords to display events of a POS device.
Port
You can configure the protocol related settings.
English _117
setup viewer
DDNS &amp; P2P
HTTPS
A remote user can network a recorder using a DDNS address in a dynamic IP system. If you cannot connect with a
dynamic IP, you can easily access using a P2P service.
You can select a security connection system or install public certificates.
Before using Wisenet DDNS &amp; P2P, please set up the network connection and DDNS first.
Setup &gt; Network &gt; HTTPS
Setup &gt; Network &gt; DDNS &amp; P2P
￭ While using HTTPS, if you want to switch to HTTP, then abnormal operation can take place as the browser contains the setting values. You need
to change the URL to HTTP and reconnect or initialize the cookie setting of the browser.
IP Filtering
You can prepare the list of IP address to allow or block accesses to a specific IP address.
Setup &gt; Network &gt; IP filtering
802.1x
When connecting to a network, you can select whether to use the 802.1x protocol and install a corresponding
certificate.
Setup &gt; Network &gt; 802.1x
118_ setup viewer
FTP
Event
When an event occurs, you can create settings related to the FTP server to which images will be transferred.
You can set the event interval and specify which events the server sends mails for.
Setup &gt; Network &gt; FTP
• setup viewer
Recipient
E-mail
You can set groups and recipients to receive emails.
You can specify the SMTP server that sends a mail if an event occurs and set the recipient group and users.
Setup &gt; Network &gt; E-mail
SMTP
You can set the server that sends mails and specify if you use the authentication process.
English _119
setup viewer
SNMP
Status
Using the SNMP protocol, the system or network administrator can remotely monitoring the network devices and
sets the environment.
You can check the IP and MAC currently used through the DHCP server, and the connected network port.
Setup &gt; Network &gt; SNMP
DHCP Server
You can set the network camera IP address and check the details by setting up a DHCP server.
Setup &gt; Network &gt; DHCP server
Network
You can set the internal DHCP server and assign an IP address to the network camera.
120_ setup viewer
Setting the System
User
You can configure the various settings of the Recorder system.
You can manage users, such as adding or deleting users and granting different authorities for each user.
For details, refer to the &quot;Setup &gt; Setting the System&quot; page in the Table of Contents.
Date/Time/Language
Administrator
• setup viewer
You can check and setup the current Date/Time and time related properties, as well as the language used for the
interface on the screen.
Setup &gt; System &gt; User
You can change the admin ID or the password.
Setup &gt; System &gt; Date/Time/Language
System Time
Set the date and time.
￭ ID allows alphanumeric characters only.
￭ If the admin ID is not used for access, you cannot change the ID.
￭ If the ID being used is changed, you will be automatically logged out.
User
You can add, change or remove a user or users.
Time sync
Set the time synchronization.
DST
During the summer, Daylight Saving Time (DST) advances clocks one hour forwards from the standard local time
zone.
Language
Select a preferred language for the Recorder.
Holiday
A user can select specific dates as holidays according to their own preferences.
English _121
setup viewer
Restriction settings
Settings
You can set the user permission.
Using a storage device, you can apply the current configuration of Recorder to another Recorder.
Press the Initialization button to return the network settings to their factory default state. Items in the
&lt;Exception&gt; category are excluded from the initialization.
System Management
You can check the current system version and update to a new version, export data, setting initialization, and
more.
Setup &gt; System &gt; System management
Log
You can check the log information related to system, events, and export.
Setup &gt; System &gt; Log
Product information
You can see information of the current system.
System log
Check the model name, software version, and MAC address.
You can search for a file from the recorder connected to the PC to perform an upgrade.
System related log information such as system startup, system shutdown, and menu setting change can be
retrieved.
122_ setup viewer
Event log
The event log lists recorded events, such as sensor events, camera events, or image losses.
• setup viewer
Export log
You can search the user who performed the export and the execution time and details (time, channel, device, file
type).
English _123
export viewer
SEC Backup Viewer
Screen Layout of the Backup Viewer
You can play a file that is backed up in the format of SEC.
Backup in SEC format produces backup data file, library file and self-executable viewer file.
If you run the backup file viewer, the backup data file will be played.
XRN-1620B2_CAM 01
Recommended System Requirements
2020-05-14 20 :54 :13
H264(1920x1080), NONE
PCs with a lower specification than the recommended below may not fully support forward/backward and
highspeed playback.
PC Specifications
Name
Minimum requirements
Recommended
CPU
Intel Pentium 2.5GHz or more
Intel i7(3.5GHz) or more
RAM
4GB or more
8GB or more
HDD
200GB or more
500GB or more
VGA memory
512MB or more
1GB or more
Display resolution
1280x1024 or higher
1920x1080 or higher
OS
Windows 7, 8, 10
Name
Description
Selects screen ratio to display.
Split screen
The screen is changed to a split screen.
Fisheye view mode
IIf &lt;
&gt; is pushed, it is possible to change to a fisheye installation type. It is possible to
select wall/ground/ceiling mode according to the installation place.
The fisheye view mode on the current screen can be changed independently on each split.
Digital Zoom
124_ export viewer
Enlarge the image by up to 100 times as big as the current one.
Press the Zoom In ( ) button the enlarge the image; press the Zoom Out ( ) button
to shrink the image. You can also use the slide bar (
) in the pop-up window to
zoom in/out.
Press ( ) on a size-changed video to restore the default zoom factor (100%). If you enlarge
the image by more than 200%, the enlarged area will be marked on the digital zooming
screen. Click on the marked area and move it to a desired position.
The digital zooming is applied to all backup viewer. When the digital zooming is canceled, the
video size will restore the default rate of 100%.
Name
Description
Saves the current video's image as in an image file. Supports JPEG file format.
Screen Printout
/
A toggle button. Each time you press this button, the audio output will toggle between
activated and deactivated.
• export viewer
Audio
Prints out the current screen. You should have installed the appropriate printer driver before
you can print out the screen.
You can adjust the volume level from 0 to 100.
Watermark
/
Press the button to enable file tampering detection, to detect data file forging.
Deinterlace
You can enable the De-interlace function.
Show OSD
Check the OSD checkbox to display the OSD information on the backup playback screen.
Information such as backup date, day of the week, time, model name, and channel number
will be displayed on the screen.
Maintain aspect
ratio/Full screen
Enlarge/Reduce
Timeline
Restore Timeline
Display of storage time range
Playback Control
Maintains the aspect ratio of the playback screen.
Plays the video on a full screen.
Collapses the time range that is displayed on the range bar of the storage time.
You can collapse the range bar until the overall range is shortened to 24 hours.
Enlarges the time range that is displayed on the range bar of the storage time. You can
enlarge the range bar until the overall range is extended to 1 minute.
Restores the timeline to the default.
Displays the time range of a stored video file.
You can move the gridline of the range bar to select a time point to play.
You can adjust the video playback of the timeline.
English _125
appendix
Use Joystick
Using Virtual Keyboard
The function is only available for the product that supports a joystick. For products that support joysticks, refer to the
&quot;Functions Supported by Model&quot; page.
The SPC-2000 joystick is operated as follows :
1. For alphanumeric inputs, the virtual keyboard window appears.
2. Using a mouse, click on the desired character tab.
3. Select &lt;OK&gt;.
Entered word is applied.
￭ If you want to enter a special character or uppercase letters, select &lt;Caps lock&gt; or &lt;Shift&gt;.
￭ Using the virtual keyboard is the same to a normal keyboard use in your region.
￭ Your ID can contain any combination of upper/lowercase alphabet letters and numbers.
￭ If the password length is 8 to 9 digits, you can combine at least three different types of the following characters : upper/lowercase alphabets, numbers, and
special characters.
Name
Description
In PTZ mode, the camera can be panned, tilted, and controlled in 8 directions.
Up/Down/Left/
Right
Rotation
The Web Viewer only supports the PTZ mode.
In Screen mode, the top/bottom/left/right tile can be selected.
￭ When you press the Near/Far button while controlling with the joystick, you can perform control simultaneously.
In PTZ mode, the screen is zoomed in when it is rotated clockwise and zoomed out when it is rotated counterclockwise.
In PTZ mode, presets number 1~8 are run.
Screen mode works as follows.
1~8
1 : Changing live layout / 2 : Search
3 : Export / 4 : Zoom mode
5 : Freeze mode / 6 : Audio
7 : Alarm / 8 : Rec
It allows to exit PTZ mode in PTZ mode.
9
The Web Viewer won't be able to stop the PTZ on its own.
This is used to change to PTZ mode from screen mode.
It allows to exit PTZ mode in PTZ mode.
10
The Web Viewer won't be able to stop the PTZ on its own.
Goes back to the previous screen in the Screen mode.
11,12
126_ appendix
In PTZ mode, Focus Near/Far operation is run.
When using the screen mode, the same operations can be done by moving the mouse.
￭ If the password length is 10 digits or more, you can combine at least two different types of the following characters : upper/lowercase alphabets, numbers,
and special characters.
Troubleshooting
Problem
Live video will be slow or cut off.
●
The video input is okay, but the videos of some channels are
not properly displayed or are abnormally displayed (e.g. black
screen, B/W screen).
The screen displays the logo image repeatedly.
The frame number set for multiple data transmission set in camera or network environment
could differ from the actual rate of transmission.
Click &lt;
&gt; at the bottom of the screen to check the number of incoming frames per
channel and the actual number of frames played.
When you register a camera, the Live4NVR profile will be created by default.
If necessary, go to “Setup &gt; Camera &gt; Profile setup &gt; Edit” and change the number of
frames.
●
If you keep seeing video slow down or cut off, then check the network environment or camera
condition.
●
Check if the power supply system is properly connected.
●
Check the system for the input voltage from the power source.
●
If the problem persists even after you have taken the above actions, check the power supplier
and replace it with a new one if necessary.
●
Check inside if the cables are properly connected. (SMPS, FRONT)
●
Check if the camera is properly supplied with power.
●
Check the state of the cable connected to the camera and reconnect it after replacing or
disconnecting it.
●
Check the video output connecting the camera's Web Viewer.
●
Check if the network port is properly connected and the network setting is set correctly.
●
Change the hub supporting Gigabit, it may solves.
●
This may occur from a problem with the main board, or the related software is corrupt.
Contact the nearest service center for more information.
The Channel button does not work on the Live screen.
●
The Channel button does not work if the current screen is in the event monitoring mode.
The cursor will not move to the Start button when I start the
calendar search.
●
Check if the channel and the date that you want to play are marked with the V symbol.
Both channel and date should be checked before you can start playing with the Start button.
The screen of the connected monitor is displayed abnormally or
not displayed at all.
●
Check if the necessary cables are connected to the monitor properly.
●
Some monitors do not support the Recorder output (HDMI1 or HDMI2/VGA). Check the
monitor resolution.
–– HDMI1 : 3840x2160(30 Hz), 1080P, 720P, 1280x1024
–– HDMI2/VGA : 1920x1080, 1280x720, 1280x1024, 1024x768
&gt; state.
No response controlling PTZ in the live viewer.
●
Disconnect the monitor cable from the recorder, and connect again.
●
The HDD may have problems. Visit your nearest customer service center to check the HDD.
●
Check the registered Camera if it support PTZ function.
Action
●
Check if the network cable is connected properly.
●
Ensure that you have set Network - Connection Mode.
●
Check the IP setting of the PC or camera.
●
Try the Ping Test.
●
Check if there is a different device near the product uses the same IP.
I registered a camera, but the web viewer does not show live
video.
●
After registering a camera, a user need to edit/save the desired layout, before the screen split
mode and live screen fit for the setting appears.
The input camera image is too bright or too dark.
●
Check the registered camera settings in “Setup &gt; Camera &gt; Camera setup”.
The time setup window will pop up.
●
This message is displayed if there occurs a problem with the time setting of the internal clock
or an error in the clock itself.
Contact the retailer or the service center for more information.
The time bar is not displayed in Search mode.
●
The timeline can switch between normal and extension mode.
In extension mode, the time bar may not be displayed in the current timeline. Switch to
normal mode or use the left or right button to navigate through the time bar.
The &quot;NO HDD&quot; icon and an error message are displayed.
●
If you do not format your purchased HDD at all or in a format supported by Recorder, a “NO
HDD” icon (
) will be displayed at the top left. When the “NO HDD” icon is displayed, go
to “Setup &gt; Device &gt; Storage device” and check the HDD connection status and format the
HDD.
●
If the problem persists in a normal condition, contact the nearest service center to have the
HDD checked by the service personnel.
I have installed an additional HDD on the Recorder but it does
not recognize the HDD.
●
See the compatibility list to check if the additional HDD is supported by the Recorder. For the
compatibility list, contact the retailer where you purchased the Recorder.
I have connected an external storage device (USB Memory, USB
HDD) to the Recorder but the Recorder seems not to recognize
it.
●
See the compatibility list of external storage devices to check if the connected device is
supported by the Recorder. For the compatibility list, contact the retailer where you purchased
the Recorder.
If I press the ESC key in full screen mode of the Web Viewer, the
system does not switch to a normal split mode.
●
Press the ALT+TAB keys to select 'ACTIVE MOVIE' and press the ESC key again. The system will
switch to a normal split mode.
It is difficult to configure the network for default search, export,
and router use.
●
For more information, refer to the user manual.
●
If you want to check the basics of the product for a quick start, refer to the Quick Guide
(export, search).
●
If you use the router for network connection, refer to the “Connecting and Setting the
Network” of the Quick Guide.
●
Contact the Recorder administrator for help.
The camera is not connected or the PC fails to connect to the
product.
I forgot the password.
English _127
• appendix
The system does not turn on and the indicator on the front
panel does not work at all.
Logo screen on bootup stalls in the &lt;
Problem
Action
appendix
Problem
Exported data cannot be played on a PC or recorder.
Recording does not work.
Action
Problem
●
When setting the file format for exporting, first decide whether the device to be played is a PC
or a recorder before setting.
●
When playing on a PC, the export file format must be SEC.
●
When playing on a recorder, the export file format must be recorder.
In the live screen, the &lt; &gt; icon is displayed and the
message window saying “Record data size exceeded limitation.
Only key frames are recorded. Please check the record settings.”
pops up.
●
If your player does not display a Live image at all, that indicates recording does not work so
first check if you see an image on the screen.
●
Recording does not work if the recording settings are not properly configured.
Scheduled Record : Specify a desired time in &quot;Setup &gt; Record &gt; Record schedule&quot;.
Recording will start at the specified time.
Action
●
If the sum of input data for each channel exceeds the limit, the alarm icon and the pop up
window will be displayed. In this case, the channel exceeding the input limit does not record
the entire frame, but it records the main frame only (one or two per sec).
●
Set the permitted data limit to higher than the amount of input data entered in the &quot;Setup &gt;
Record &gt; Record setup&quot; menu.
Recording is not performed in accordance with the settings.
●
If the recording status displays 'Exceeds the maximum hard disc performance', set the
recording size according to the recording performance specifications for each HDD condition.
For details, refer to the &quot;Setup &gt; Setting the Recording” page in the Table of Contents.
The recording screen will slow down.
●
Check whether the recording performance specifications for each HDD condition match the
actual recording settings.
For details, refer to the &quot;Setup &gt; Setting the Recording” page in the Table of Contents.
●
If the data volume of a video exceeds the playing performance, only the main frame is played.
●
Reset the camera recording profile to let the entire recording bps size fit the recording
performance for each HDD condition.
For details, refer to the &quot;Setup &gt; Setting the Recording” page in the Table of Contents.
●
Check the HDD status and determine whether inspection or replacement is necessary.
For details, refer to the &quot;Setup &gt; Setting the Device &gt; Storage device&quot; page in the Table
of Contents.
●
If your camera is using a manual IP, the IP bandwidth might not match with the Network 1 IP
bandwidth of the recorder. Please set it to the identical IP bandwidth.
●
If your camera is in DHCP mode, see if the Network 1 port is functioning in the DHCP server of
the recorder.
–– Continuous : Recording will proceed in any conditions at the specified time.
–– Event : When an event occurs, recording will perform only if the event is of alarm,
motion detection and video loss. If there is no event found, recording will not perform.
–– Continuous/Event : If there is no event found, continuous recording will perform.
Whereas, if an event occurs, event recording will perform.
The image quality of the recording data is not good.
●
Increase the resolution and quality level in &quot;Setup &gt; Camera &gt; Profile setup &gt; Record&quot;.
–– Resolution : Select a bigger size when specifying the recording size.
The recording image in the CIF format shows a deteriorated quality as it is enlarged
from a small-sized image.
–– Frame rate : Set the level of frame rate high.
●
If you increase the resolution and the recording quality, the data size increases accordingly.
So the HDD will be filled faster. Overwriting will overwrite the existing data so recording will
proceed at a shorter interval.
Frame rate of the actual recording does not match that of
configured to the camera.
●
If multiple profiles were applied to one camera for video transmission, the actual video stream
can be serviced by the camera at a lower frame rate than specified.
Configure your camera to use one profile for data streaming as possible.
For example, if you set the same profile for recording and network profiles, the actual
recording is made at the specified frame rate.
Still, live video display using split screen mode may apply yet another profile to camera in
accordance with the used screen mode.
Note that allowed limit bitrate for recording / recording settings should be set to be bigger
values than that of camera's feed.
In the recording setting screen, the permitted level for a specific
channel is displayed in orange.
●
If the input data is greater than the permitted level for each channel, it is displayed in orange.
Set the permitted data limit to higher than the amount of input data.
●
If the sum of input data for each channel exceeds the limit, the alarm icon will be displayed. In
this case, the channel exceeding the input limit does not record the entire frame, but it records
the main frame only (one or two per sec).
128_ appendix
If recording loss persists continuously
When registering your camera in PnP mode, if the camera
doesn't get registered but the logo keeps loading attempting
access.
">
Hello! I am an AI chatbot specifically trained to assist you with the Wisenet XRN-3210B4 User Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!
Assistant typing
Assistant terminated
Related

Wisenet XRN-1610A, XRN-1610S, XRN-2010, XRN-2010A Quick Manual

Wisenet XRN-1620SB1 Quick Manual

Wisenet CT-XRN-420S, XRN-420S Quick Manual

Samsung XRN-1610, XRN-1610S User Manual

WISeNeT QRN-1630S Network Video Recorder Quick Guide

WISeNeT PRN-3200B2 Network Video Recorder Instruction manual

SAMSUNG XRN 2010, XRN 2011 User Manual

Wisenet XRN-815S User Manual - Network Video Recorder

Wisenet QRN-430S Product Specifications Manual

Wisenet XRN-6410RB2 User Manual

WISeNeT ARN-410S IP Security Network Video Recorder User Guide

WISeNeT HRX-1635-48TB Digital Video Recorder User Guide
