ADS Omegalink OL-RS-VW1 Product Manual

The ADS Omegalink OL-RS-VW1 is a remote starter solution for Volkswagen vehicles. It offers enhanced features and requires proper firmware programming before installation. The manual guides you through installation, programming, and troubleshooting, ensuring a seamless setup and operation.

PDF

Document

PRODUCT GUIDE
OL-RS-VW1
DOCUMENT NUMBER
REVISION DATE
20180116
NOTICE
The manufacturer will accept no responsability for any electrical damage resulting from
improper installation of this product, be that either damage to the vehicle itself or to the
installed device. This device must be installed by a certified technician. Please review the
Installation Guide carefully before beginning any work.
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. &copy; 2018
www.idatalink.com
PAGE 2 OF 12
• 20180116
GETTING STARTED
WELCOME
Congratulations on the purchase of your VW
solution. You are now a few simple steps away
from enjoying your new remote starter unit with
enhanced features.
Before starting your installation, please ensure that
your VW module is programmed with the correct
firmware for your vehicle and that you carefully
review the install guide.
TABLE OF CONTENTS
Box Contents
3
Tach Programming Procedure
4
Remote Programming Procedure
5
Valet Mode Programming Procedure
6
Compatible Accessories
7
Online Module Settings
9
Module Diagnostics
10
Remote Starter Error Codes
11
Module Reset Procedure
12
NEED HELP?
1 866 427-2999
[email protected]
idatalink.com/support
www.12voltdata.com/forum
www.facebook.com/groups/idatatech
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. &copy; 2018
OL-RS-VW1
www.idatalink.com
PAGE 3 OF 12
• 20180116
BOX CONTENTS - 1 OF 1
BOX CONTENTS
MODULE
AUTOMATIC
TRANSMISSION
CUT LOOP
2 1
4 3
6 5
8 7
10 9
12 11
M2 01 GREEN•BLACK DOT - LOCK (-) OUTPUT
02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT
03 RED/WHITE•BLACK DOT - TRUNK RELEASE (-) OUTPUT
04 EMPTY
05 EMPTY
06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT
07 BROWN•BLACK DOT - SIREN (+) OUTPUT
08 WHITE/PURPLE•BLACK DOT
09 PURPLE/BLACK•BLACK DOT - RAP SHUTDOWN (-) OUTPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
11 BROWN/BLACK•BLACK DOT - GROUND WHEN ARMED (-) OUTPUT
12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT
2
4
6
8
10
M3 01 EMPTY
02 EMPTY
03 EMPTY
04 EMPTY
05 EMPTY
06 WHITE/BLUE•SILVER DOT - X-TRIGGER (-) INPUT
07 GRAY•SILVER DOT - HOOD (-) INPUT
08 EMPTY
09 EMPTY
10 TAN•SILVER DOT - EXT ALARM SENSOR (-) INPUT
M5 - 6 PIN BLUE
M2 - 12 PIN BLACK
M3 - 10 PIN WHITE
M4 - 20 PIN BLACK
TELEMATIC 1 - 4 PIN BLUE
2 PIN BLACK - LED
TELEMATIC 2 - 4 PIN RED
PROGRAMMING BUTTON
LED 2
1
3
5
7
9
LED 1
THERMISTOR - 2 PIN BLUE
NC - 4 PIN RED
RF PORT/WEBLINK PORT - 4 PIN BLACK
USB
M5
1
3
5
2
4
6
FUNCTIONS DEFINED BY FIRMWARE
VS9
JS12
VS1
VS10
VS2
VS5
JS10
JS4
GOLF
JS1
MS1
JS2
STICKERS
VS6
JS3
HOOD SWITCH
JS5
PTS
VS3
JS6
KEY
VS4
2X
JS7
VS7
JS8
JS11
VS8
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. &copy; 2018
OL-RS-VW1
JS9
www.idatalink.com
01
TACH PROGRAMMING PROCEDURE - 1 OF 1
PAGE 4 OF 12
• 20180116
OL-RS-VW1
www.idatalink.com
START vehicle for 15 seconds.
OFF
ACC
ON START
ENGINE
START
STOP
02
Press and hold the brake pedal.
03
Press and release the module’s programming
button. (OR if the remotes are already
programmed to the vehicle, press and hold the
start button of the remote for 2.5 seconds.)
04
Wait, LED 2 will flash GREEN. (See the Module
Diagnostics page)
05
Release the brake pedal.
06
Module Programming Procedure completed.
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. &copy; 2018
AFTERMARKET REMOTE PROGRAMMING - 1 OF 1
PAGE 5 OF 12
• 20180116
OL-RS-VW1
www.idatalink.com
AFTERMARKET REMOTE PROGRAMMING:
NOTES
I All aftermarket remotes must be programmed to the
RF-Kit.
Refer to the RF-Kit user guide for aftermarket remote
features and programming procedures.
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. &copy; 2018
VALET MODE PROGRAMMING PROCEDURE - 1 OF 1
&gt;&gt;
NOTE: In Valet Mode, the Remote starter is not
functional. Keyless entry, Lock and Unlock will
remain functional. See RF kit user manual for
alternate valet mode programming.
06
Valet Mode Programming Procedure
completed.
01
Time restriction. Complete next step within 7
seconds.
&gt;&gt;
To exit valet mode: repeat steps 1 to 5.
02
PAGE 6 OF 12
• 20180116
Cycle ignition ON twice [2x OFF/ON] rapidly.
OFF
ACC
ON START
ENGINE
START
STOP
03
Press and release the BRAKE pedal three
times [3x].
04
Parking Light will flash once [1x] then will
flash twice [2x].
05
Set ignition to OFF position.
OFF
ACC
ON START
ENGINE
START
STOP
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. &copy; 2018
OL-RS-VW1
www.idatalink.com
PAGE 7 OF 12
• 20180116
COMPATIBLE ACCESSORIES - 1 OF 2
WEBLINK CABLE (required accessory sold separately)
WEBLINK CABLE
MODULE
WEBLINK PORT
COMPUTER
USB PORT
4 PIN BLACK CABLE
WEBLINK MOBILE (accessory sold separately)
OBDII CONNECTOR
4 PIN BLACK CABLE
MODULE
WEBLINK PORT
MOBILE DEVICE
PORT
1
2
3
4
5
6
7
8
OBDII CONNECTOR
9
10
11
12
13
14
15
16
TELEMATIC KIT (accessory sold separately)
(NC)
MODULE
TELEMATIC BLUE PORT
*For SmartStart, use the module’s RED Telematic port.
RF KIT (accessories sold separately)
OMEGA RF KIT
MODULE
RF PORT
(NC)
ANTENNA
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. &copy; 2018
OL-RS-VW1
www.idatalink.com
PAGE 8 OF 12
• 20180116
COMPATIBLE ACCESSORIES - 2 OF 2
RF KIT (accessories sold separately)
ADSHRNRSXL02
DIRECTED XL202 RF KIT
MODULE
RF PORT
XL202 RF DECODER
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. &copy; 2018
XL202 ANTENNA
OL-RS-VW1
www.idatalink.com
ONLINE MODULE SETTINGS - 1 OF 1
WEB PROGRAMMABLE MENUS
DESCRIPTION
MENU 1 – Remote Starter
RS related configuration options
MENU 2 – Doorlock Options
Convenience feature configuration options
MENU 3 – Security Options
Alarm activation and settings
MENU 4 – AUX function assignments
Set transmitter AUX buttons controls
MENU 5 – Programmable outputs (POC)
Set actions for programmable outputs
MENU 6 – Pulse Timer Output Configuration (PTO)
Set duration for pulse timer outputs (if used)
MENU 7 – Input Configurations
Set inputs for Auto by firmware/Data/Analog
MENU 8 – Output Configurations
Programming options are avaible through Weblink and Weblink Mobile only.
Set outputs for Auto by firmware/Data/Analog
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. &copy; 2018
OL-RS-VW1
PAGE 9 OF 12
• 20180116
www.idatalink.com
I
II
III
IV
DURING MODULE PROGRAMMING
DURING TACH PROGRAMMING
DURING REMOTE START
WITH IGNITION OFF
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. &copy; 2018
DIAGNOSTIC
TEST MODULE
LED 1 STATUS
MODULE DIAGNOSTICS - 1 OF 1
Flashing RED
Missing/wrong information from firmware or vehicle.
Solid RED
Module waiting for more vehicle information.
Flashing GREEN
Additional steps required to complete module programming.
Solid GREEN then OFF
Module correctly programmed.
OFF
No activity or module already programmed.
1 GREEN flash
Tach signal programmed in Analog
2 GREEN flashes
Tach signal programmed in Data
3 RED flashes
No tach signal detected
4 RED flashes
System is in valet mode
5 RED flashes
Tach set for ‘VTS’. No tach programming required
6 RED flashes
Tach set for ‘assumed start’. No tach programming required
Flashing RED
Module incorrectly programmed.
Solid RED
Module incorrectly programmed.
Flashing GREEN
Module correctly programmed and operational.
Solid GREEN then OFF
Reset in progress.
OFF
Invalid ground when running status from remote starter.
Flashing RED
Module incorrectly programmed or connected.
Solid RED
Module not programmed. Waiting for more vehicle information.
Flashing GREEN
False ground when running status from remote starter.
Solid GREEN then OFF
Reset in progress.
OFF
Module at rest and ready for a remote start sequence.
OL-RS-VW1
PAGE 10 OF 12
• 20180116
www.idatalink.com
[X] NUMBER OF
PARKING LIGHT
FLASHES
DIAGNOSTIC
REMOTE STARTER ERROR CODES - 1 OF 1
I WARNING: The following applies only when the parking
lights are connected and supported by the system.
01
Engine running.
02
Key in ignition at ON position.
II After a remote starter failure, the parking lights will flash
three [3x] times, then will flash [X] number times to
indicate an error code. See table.
03
Door is open.
04
Trunk is open.
05
Foot brake is ON.
06
Hood is open.
07
The reservation is OFF. (Manual transmission only)
08
Tach failure.
09
The vehicle is moving (VSS).
10
System is in Valet Mode.
11
CAN communication failure
12
RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence.
13
Bypass problem.
[Y] NUMBER OF
PARKING LIGHT
FLASHES
DIAGNOSTIC
REMOTE STARTER ERROR CODES:
NOTES
I WARNING: The following applies only when the parking
lights are connected and supported by the system.
01
Engine tach signal is lost.
02
Emergency brake is lost.
II If the engine shuts down after a remote starter sequence:
Press and hold the Trunk button and the Start button at the
same time for 2.5 seconds when using a 1-WAY remote.
OR
Press once [1x] on button “4” when using a 2-WAY remote.
03
Foot brake is ON.
04
Hood is open.
05
Engine RPM limiter is ON.
06
Glow plug timeout error.
07
Vehicle is moving (VSS).
08
N/A
09
N/A
10
Door is open.
11
CAN communication failure during RS sequence.
12
RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence.
13
Takeover is not allowed.
14
Shutdown error, board overheat protection.
REMOTE STARTER SHUTDOWN ERROR CODES:
NOTES
The parking lights will flash four [4x] times, then will flash
[Y] number times to indicate an error code. See table.
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. &copy; 2018
OL-RS-VW1
PAGE 11 OF 12
• 20180116
www.idatalink.com
MODULE RESET PROCEDURE - 1 OF 1
&gt;&gt;
The following procedure resets the module
programming to the vehicle. It does not reset
any settings configured online.
06
Module RESET completed.
01
Disconnect all connectors from module except
the M1 BLACK 8-pin connector and the M4
BLACK 20-pin connector.
07
Reconnect all connectors.
02
Disconnect the M1 BLACK 8-pin connector
and the M4 BLACK 20-pin connector.
08
Repeat programming procedure.
03
PRESS AND HOLD the module’s programming
button while connecting the M1 BLACK
8-pin connector and the M4 BLACK 20-pin
connector.
&gt;&gt;
Failure to follow procedure may result with a
DTC or a CHECK ENGINE error message.
04
Wait, LED 1 will flash RED. RELEASE
programming button.
05
LED 1 will turn RED for 2 seconds.
U.S. Patent No. 8,856,780
Automotive Data Solutions Inc. &copy; 2018
OL-RS-VW1
PAGE 12 OF 12
• 20180116
www.idatalink.com
">

Hello! I am an AI chatbot specifically trained to assist you with the ADS Omegalink OL-RS-VW1 Product Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant is out of keyboard. Please, try again later.

Key features

Remote start
Programmable outputs
Weblink compatible
Valet mode
Module diagnostics
Tach programming
Error codes
Remote programming

Frequently asked questions

Refer to the RF-Kit user guide for aftermarket remote features and programming procedures.

Missing/wrong information from firmware or vehicle.

Disconnect all connectors except M1 and M4, then connect M1 and M4 while holding the programming button. Release the button when LED 1 flashes red, and wait for LED 1 to turn red for 2 seconds. Reconnect all connectors and repeat the programming procedure.