SAF Fixed RPM Series
Indoor Units
SAF024
SAF045
Outdoor Units
OU7-24Z
OU10-47T
GC 45
REFRIGERANT
COOLING ONLY
R22
HEAT PUMP
R410A
SM SAFRPM 1-A.0 GB
AUGUST 2009
CONTENTS
LIST OF EFFECTIVE PAGES
LIST OF EFFECTIVE PAGES
Note: Changes in the pages are indicated by a “Revision#” in the footer of each effected page
(when none indicates no changes in the relevant page). All pages in the following list represent
effected/ non effected pages divided by chapters.
Dates of issue for original and changed pages are:
Original ....... 0 ........ March 2009
Total number of pages in this publication is 53 consisting of the following:
Page
No.
Revision
No. #
Title ...........................
A................................
i .................................
1-1 - 1-2 ....................
2-1 - 2-3 ....................
3-1.............................
4-1 - 4-2 ....................
5-1 - 5-12 ..................
6-1 - 6-2 ....................
7-1 - 7-5 ....................
8-1.............................
9-1.............................
10-1 ..........................
11-8 ...........................
12-1...........................
13-10.........................
14-1...........................
•
Page
No.
Revision
No. #
Page
No.
Revision
No. #
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Zero in this column indicates an original page.
*Due to constant improvements please note that the data on this service manual can be modified with out notice.
**Photos are not contractual.
A
SM SAFRPM 1-A.0 GB
CONTENTS
TABLE OF CONTENTS
Table of Contents
1.
INTRODUCTION ...................................................................................................1-1
2.
PRODUCT DATA SHEET ......................................................................................2-1
3.
RATING CONDITIONS ..........................................................................................3-1
4.
OUTLINE DIMENSIONS .......................................................................................4-1
5.
PERFORMANCE DATA & PRESSURE CURVES ................................................5-1
6.
SOUND LEVEL CHARACTERISTICS ..................................................................6-1
7.
WIRING DIAGRAMS .............................................................................................7-1
8.
ELECTRICAL DATA ..............................................................................................8-1
9.
REFRIGERATION DIAGRAMS .............................................................................9-1
10. TUBING CONNECTIONS......................................................................................10-1
11.
CONTROL SYSTEM .............................................................................................11-1
12. TROUBLESHOOTING ..........................................................................................12-1
13. EXPLODED VIEWS AND SPARE PARTS LISTS .................................................13-1
14. APPENDIX A .........................................................................................................14-1
SM SAFRPM 1-A.0 GB
i
INTRODUCTION
1.
INTRODUCTION
1.1
General
The floor-standing air conditioner of SAF fixed RPM series has some strongpoint, such as modern
outlook, excellent quality, amazing price. It comprise RC, RH, models, as follows:
• SAF024 R410A
• SAF045 R410A
• SAF045 R22
1.2
Main Features
The SAF Fixed RPM series benefits from the most advanced technological innovations, namely:
• LCD display
• Ionizer as an option
• Auxiliary PTC heater as an option.
• Automatic vertical louver
• Pre-charged system up to 10m for model 24 R410A
• Pre-charged system up to 15m for model 45 R410A
• Up to 50 Meter tubing length (in model 45) R22
• Scroll compressor (in model 45)
• Compact size of outdoor units.
• Easy installation and service.
1.3
Indoor Unit
The indoor unit is floor-standing type indoor unit, and can be easily fitted to many types of residential
and commercials applications as restaurant, shops, reception room etc.
It includes:
• Coil with hydrophilic aluminum fins.
• Motorized air flap.
• Low sound level of the indoor fan
1.4
Control
The microprocessor indoor controller, and an infrared remote control, supplied as standard, provide
complete operating function and programming. For further details please refer to the Owner’s
Manual, Appendix A.
1.5
Outdoor Unit
The outdoor units can be installed as floor or wall mounted units by using a wall supporting bracket.
The metal sheets are protected by anti- corrosion paint work allowing long life resistance. All outdoor
units are pre-charged. For further information please refer to the Product Data Sheet.
It includes :
• Compressor mounted in a soundproofed compartment .
• Axial fan.
• Outdoor coil with hydrophilic louver fins for RC units.
• Outlet air fan grill.
• Service valves” flare” type connection.
• Interconnecting wiring terminal block.
SM SAFRPM 1-A.0 GB
1-1
CONTENTS
INTRODUCTION
1.6
Tubing Connections
Flare type interconnecting tubing to be produced on site.
For further details please refer to the Owner’s Manual.
1.7
Accessories
Remote Control
1.8
Inbox Documentation
Each unit is supplied with its Owner’s Manual.
1.9
Matching Table
Indoor Unit
SAF024 SAF045
Outdoor Unit
OU7-24Z

OU10-47T

GC 45 R22

SM SAFRPM 1-A.0 GB
1-2
CONTENTS
PRODUCT DATA SHEET
2.
PRODUCT DATA SHEET
2.1
SAF024 / OU7-24Z R410A
Model Indoor Unit
Model Outdoor Unit
Installation Method of Pipe
Characteristics
Capacity
Units
Btu/hr
kW
kW
W/W
(4)
Power input (4)
EER (Cooling) or COP(Heating) (4)
Energy efficiency class
Power supply
OUTDOOR
INDOOR
Rated current
Power factor
Prated (IDU)
Prated (IDU+ODU)
Starting current
Circuit breaker rating
Fan type & quantity
Fan speeds
H/M/L
H/M/L
Air flow (1)
External static pressure
Min
H/M/L
Sound power level (2)
H/M/L
Sound pressure level (3)
Moisture removal
Condenstate drain tube I.D
Dimensions
WxHxD
Net Weight
Package dimensions
WxHxD
Packaged weight
Units per pallet
Stacking height
Refrigerant control
Compressor type,model
Fan type & quantity
Fan speeds
H
Air flow
H
Sound power level
H
H
Sound pressure level (3)
Dimensions
WxHxD
Net Weight
Package dimensions
WxHxD
Packaged weight
Units per pallet
Stacking height
Refrigerant type
Standard charge
Additional charge
Liquid line
Suction line
Connections between
Max.tubing length
units
Max.height
difference
Operation control type
Heating elements (Option)
Others
Cooling Only
22690
6.65
2.37
2.81
C
V
Ph
Hz
A
10.8
0.95
W
W
A
A
RPM
m3/hr
Pa
dB(A)
dB(A)
l/hr
mm
mm
kg
mm
kg
units
units
RPM
m3/hr
dB(A)
dB(A)
mm
kg
mm
kg
Units
units
SAF024
OU7-24Z
Flared
Cooling
22690
6.65
2.37
2.81
C
220-240
1
50
10.8
0.95
150
3500
66
20
Centrifugal x 1
470/430/380
1000/915/809
0
58/54/52
48/44/42
2.4
25
480x1730x300
36
572x1848x410
45
4
4 levels
Capillary tube
Rotary
Axial x 1
850
3100
Heating
25080
7.35
2.29
3.21
C
10.5
0.95
67
58
In.(mm)
In.(mm)
m.
900x680x340
78
985x730x435
82
6
2
R410A
2.02kg
4m < Length < 10m: +0g; 10m < Length < 15m: +0g
3/8"(9.53)
5/8"(15.88)
Max.15
m.
Max.7
kW
Remote control
2.1
kg(7.5m)
(1)
Airflow in ducted units;at nominal external static pressure.
Sound power in ducted units is measured at air discharge.
(3)
Sound pressure level measured at 1-meter distance from unit.
(4)
Rating conditions in accordance to ISO 5151 and ISO 13253 (for ducted units).
(5)
The declared value’s tolerance is in accordance with Eurovent.
(2)
SM SAFRPM 1-A.0 GB
2-1
CONTENTS
PRODUCT DATA SHEET
2.2
SAF045 / OU10-47T R410A
Model Indoor Unit
Model Outdoor Unit
Installation method
Characteristics
Capacity
(1)
OUTDOOR
INDOOR
Power input (1)
COP (1)
Energy efficiency class
Power supply
Rated current
Starting current
Circuit breaker rating
Fan type & quantity
Fan speeds
H/ M/ L
Air flow (2)
H/ M/ L
External static pressure
Min-Max
H/ M/ L
Sound power level (3)
H/ M/ L
Sound pressure level (4)
Moisture removal
Condensate drain tube I.D
Dimensions
W/ H / D
Weight
Package dimensions
W/ H / D
Packaged weight
Units per pallet
Stacking height
Refrigerant control
Compressor type, model
Fan type & quantity
Fan speeds
H/L
Air flow
H/L
Sound power level
H/L
H/L
Sound pressure level (4)
Dimensions
W/ H / D
Weight
Package dimensions
W/ H / D
Packaged weight
Units per pallet
Stacking height
Refrigerant type
Refrigerant charges distance
Additional charge per 1 meter
Liquid line
Suction line
Connections
between units
Max. tubing length
Max. height difference
Operation control type
Heating elements
Others
(1)
(2)
(3)
(4)
SAF045(FS)
OU10-47T R410A
FLARED
Units
Btu/hr
kW
kW
W/W
Cooling
41970
12.30
4.38
2.81
C
V/ Ph /Hz
A
A
A
RPM
m³/hr
Pa
dB(A)
dB(A)
L/hr
mm
mm
kg
mm
kg
Units
Units
RPM
m³/hr
dB(A)
dB(A)
mm
kg
mm
kg
Units
Units
kg/m
g/m
In.(mm)
In.(mm)
m.
m.
Heating
47090
13.8
4.37
3.16
D
400/3/50
3x8.6
550
1700
64
54
540
632
900
985
3x8.6
49
3x20A
Centrifugal&1
480
380
1500
1188
N/A
62
60
52
50
4.5
25
1776
415
52
1893
535
60
6
2
Capillary
Scroll
Axial & 2
1220
4500
71
64
970
340
91
1020
435
95
6
2
R 410A
2,3/15
25
3/8”(9.53)
3/4”(19.05)
50
25
LCD Remote Control
kW
Crankcase heater (50W),3 Phase Protector
Rating conditions in accordance to ISO 5151 and ISO 13253 (for ducted units).
Airflow in ducted units; at nominal external static pressure.
Sound power in ducted units is measured at air discharge.
Sound pressure level measured at 1-meter distance from unit.
SM SAFRPM 1-A.0 GB
2-2
CONTENTS
PRODUCT DATA SHEET
2.3
SAF045 / GC 45 R22
Model Indoor Unit
Model Outdoor Unit
Installation Method of Pipe
Characteristics
Capacity
Units
Btu/hr
kW
kW
W/W
(4)
Power input (4)
EER (Cooling) or COP(Heating) (4)
Energy efficiency class
V
Ph
Hz
A
Power supply
OUTDOOR
INDOOR
Rated current
Power factor
Prated (IDU)
Prated (IDU+ODU)
Starting current
Circuit breaker rating
Fan type & quantity
Fan speeds
Air flow (1)
External static pressure
Sound power level (2)
Sound pressure level (3)
Moisture removal
Condenstate drain tube I.D
Dimensions
Net Weight
Package dimensions
Packaged weight
Units per pallet
Stacking height
Refrigerant control
Compressor type,model
Fan type & quantity
Fan speeds
Air flow
Sound power level
Sound pressure level (3)
Dimensions
Net Weight
Package dimensions
Packaged weight
Units per pallet
Stacking height
Refrigerant type
Standard charge
W
W
A
A
H/M/L
H/M/L
Min
H/M/L
H/M/L
RPM
m3/hr
Pa
dB(A)
dB(A)
l/hr
mm
mm
kg
mm
kg
units
units
WxHxD
WxHxD
H
H
H
H
WxHxD
RPM
m3/hr
dB(A)
dB(A)
mm
kg
mm
kg
Units
units
WxHxD
kg(7.5m)
Additional charge
Connections between
units
Operation control type
Heating elements (Option)
Others
Liquid line
Suction line
Max.tubing length
Max.height
difference
In.(mm)
In.(mm)
m.
SAF045
GC 45
Flared
Cooling Only
Cooling
Heating
43670
43670
52540
12.80
12.80
15.40
4.56
4.56
5.12
2.81
2.81
3.01
C
C
D
400
3
50
8.1
8.1
9.1
0.85
0.85
0.85
160
6500
65.8
3X20
Centrifugal x 1
550/480/380
1700/1500/1188
0
64/62/60
54/52/50
4.5
25
540x1776x415
52
632x1893x535
60
6
2 levels
Capillary tube
Scroll,Dakin JT160BCBY1L
Propeller(direct)x 2
780
4680
64
56
950x1260x412
120
1100x1300x470
150
1
1
R22
3.1kg
4m < Length < 7.5m: +0g; 7.5m < Length <
25m: +500g; 25m < Length < 38m: +980g;
38m<Length<50m: +1580g;
3/8"(9.53)
3/4"(19.05)
Max.50
m.
Max.20
kW
Remote control
2.1
(1)
Airflow in ducted units;at nominal external static pressure.
Sound power in ducted units is measured at air discharge.
(3)
Sound pressure level measured at 1-meter distance from unit.
(4)
Rating conditions in accordance to ISO 5151 and ISO 13253 (for ducted units).
(5)
The declared value’s tolerance is in accordance with Eurovent.
(2)
SM SAFRPM 1-A.0 GB
2-3
CONTENTS
RATING CONDITIONS
3.
RATING CONDITIONS
Standard conditions in accordance with ISO 5151, ISO 13253 (for ducted units)
and EN 14511.
Cooling:
Indoor:
27oC DB 19oC WB
Outdoor: 35 oC DB
Heating:
Indoor:
20oC DB
Outdoor: 7oC DB 6oC WB
3.1
Operating Limits
R410A
Indoor
Cooling
Heating
Voltage
Outdoor
Upper limit
32oC DB 23oC WB
46oC DB
Lower limit
21oC DB 15oC WB
21oC DB
Upper limit
27oC DB
24oC DB 18oC WB
Lower limit
10oC DB
-9oC DB -10oC WB
1PH
198 – 264 V
R22
Indoor
Cooling
Heating
Voltage
Outdoor
Upper limit
32 C DB 23 C WB
46 C DB
Lower limit
21oC DB 15oC WB
21oC DB
Upper limit
27oC DB
24oC DB 18oC WB
Lower limit
10oC DB
-5oC DB -6oC WB
o
1PH
o
o
198 – 264 V
SM SAFRPM 1-A.0 GB
3-1
CONTENTS
OUTLINE DIMENSIONS
4.
OUTLINE DIMENSIONS
4.1
Indoor Unit: SAF024, SAF045
C
Model
SAF024
SAF045
A
485 mm
545 mm
B
300 mm
420 mm
C
1730 mm
1780 mm
A
B
4.2
Outdoor Unit: OU7-24Z R410A
SM SAFRPM 1-A.0 GB
4-1
CONTENTS
OUTLINE DIMENSIONS
4.3
Outdoor Unit: OU10-47T R410A
4.4
Outdoor Unit: GC 45 R22
950
187.5
81
80.8
378
340
112.5
65.4
572
1270
SM SAFRPM 1-A.0 GB
4-2
CONTENTS
PERFORMANCE DATA & PRESSURE CURVES
5.
PERFORMANCE DATA
5.1
SAF024 / OU7-24 Z R410A
5.1.1
Cooling Mode at 7.5m Tubing Connection.
230V : Indoor Fan at High Speed.
ENTERING AIR
DB OD Coil(oC)
15
20
(1)
(1)
25
30
35
40
46
ENTERING AIR WB/DB ID Coil(oC)
15/21
17/24
19/27
21/29
23/32
Data
TC
SC
PI
TC
SC
PI
TC
SC
PI
TC
SC
PI
TC
SC
PI
TC
SC
PI
TC
SC
PI
7.01
4.88
7.26
5.09
7.43
5.28
7.61
5.42
7.72
5.52
1.68
1.68
1.69
1.69
1.70
6.78
4.78
7.15
5.04
7.37
5.25
7.55
5.40
7.71
5.50
1.82
1.83
1.84
1.85
1.85
6.42
4.66
6.93
4.94
7.28
5.21
7.50
5.36
7.69
5.46
1.97
1.99
2.00
2.01
2.03
6.00
4.51
6.53
4.79
7.06
5.10
7.31
5.25
7.53
5.35
2.13
2.16
2.18
2.19
2.21
5.56
6.03
6.65
6.98
7.31
4.29
4.60
4.98
5.12
5.22
2.29
2.33
2.37
2.39
2.40
5.05
4.04
5.50
4.35
6.00
4.71
6.56
4.86
6.90
4.96
2.47
2.51
2.56
2.59
2.61
4.38
3.72
2.70
4.79
3.99
2.74
5.27
4.30
2.81
5.82
4.45
2.85
6.27
4.54
2.88
LEGEND
TC
SC
PI
WB
DB
ID
OD
–
–
–
–
–
–
–
Total Cooling Capacity, kW
Sensible Capacity, kW
Power Input, kW
Wet Bulb Temp., (oC)
Dry Bulb Temp., (oC)
Indoor
Outdoor
(1) Marked area is below standard operating limits. For operating in low ambient
conditions, Optional Accessories are needed.
SM SAFRPM 1-A.0 GB
5-1
CONTENTS
PERFORMANCE DATA & PRESSURE CURVES
5.1.2
Heating Mode at 7.5m Tubing Connection.
230V : Indoor Fan at High Speed.
ENTERING AIR DB ID COIL(Oc)
15
20
25
ENTERING
WB OD COIL(oC)
TH
Pl
TH
Pl
TH
Pl
-10
3.86
1.83
3.71
1.95
3.56
2.05
-7
4.15
1.88
4.01
1.98
3.86
2.09
-2
4.41
1.90
4.26
2.02
4.12
2.13
2
5.37
1.99
5.15
2.12
4.92
2.24
6
7.57
2.14
7.35
2.29
7.09
2.43
10
8.23
2.26
8.01
2.42
7.79
2.58
15
8.89
2.36
8.67
2.54
8.45
2.70
20
9.37
2.43
9.15
2.63
8.89
2.84
LEGEND
TH
PI
WB
DB
ID
OD
5.1.3
–
–
–
–
–
–
Total Heating Capacity, kW
Power Input, kW
Wet Bulb Temp., (oC)
Dry Bulb Temp., (oC)
Indoor
Outdoor
Capacity Correction Factor Due to Tubing Length
Cooling
TOTAL TUBING LENGTH
3m
7.5m
10m
15m
20m
25m
30m
40m
50m
1.02
1
0.981
0.966
---
---
---
---
---
* Minimum recommended tubing length between indoor and outdoor units is 3m.
Heating
TOTAL TUBING LENGTH
3m
7.5m
10m
15m
20m
25m
30m
40m
50m
1.05
1
0.99
0.983
---
---
---
---
---
* Minimum recommended tubing length between indoor and outdoor units is 3m.
SM SAFRPM 1-A.0 GB
5-2
CONTENTS
PERFORMANCE DATA & PRESSURE CURVES
5.2
SAF045 / OU10-47T R410A
5.2.1
Cooling Mode at 7.5m Tubing Connection.
230V : Indoor Fan at High Speed.
ENTERING AIR
DB OD Coil(oC)
15
20
(1)
(1)
25
30
35
40
46
ENTERING AIR WB/DB ID Coil(oC)
15/21
17/24
19/27
21/29
23/32
Data
TC
SC
PI
TC
SC
PI
TC
SC
PI
TC
SC
PI
TC
SC
PI
TC
SC
PI
TC
SC
PI
12.96
9.22
13.43
9.61
13.74
9.98
14.07
10.23
14.28
10.42
3.11
3.11
3.12
3.12
3.14
12.54
9.03
13.22
9.52
13.64
9.92
13.96
10.21
14.26
10.39
3.37
3.38
3.39
3.41
3.42
11.87
8.80
12.81
9.34
13.47
9.85
13.88
10.13
14.22
10.32
3.64
3.67
3.69
3.72
3.74
11.10
8.52
12.08
9.06
13.05
9.63
13.52
9.91
13.92
10.10
3.93
3.99
4.02
4.05
4.09
10.28
11.15
12.30
12.92
13.53
8.10
8.69
9.41
9.68
9.87
4.24
4.31
4.38
4.41
4.44
9.34
7.64
10.17
8.22
11.10
8.90
12.14
9.18
12.76
9.37
4.57
4.64
4.72
4.78
4.83
8.11
7.04
5.00
8.86
7.54
5.07
9.75
8.12
5.19
10.77
8.40
5.26
11.60
8.59
5.32
LEGEND
TC
SC
PI
WB
DB
ID
OD
–
–
–
–
–
–
–
Total Cooling Capacity, kW
Sensible Capacity, kW
Power Input, kW
Wet Bulb Temp., (oC)
Dry Bulb Temp., (oC)
Indoor
Outdoor
(1) Marked area is below standard operating limits. For operating in low ambient
conditions, Optional Accessories are needed.
SM SAFRPM 1-A.0 GB
5-3
CONTENTS
PERFORMANCE DATA & PRESSURE CURVES
5.2.2
Heating Mode at 7.5m Tubing Connection.
230V : Indoor Fan at High Speed.
ENTERING AIR DB ID COIL(Oc)
15
20
25
ENTERING
WB OD COIL(oC)
TH
Pl
TH
Pl
TH
Pl
-10
7.25
3.50
6.97
3.72
6.69
3.91
-7
7.80
3.58
7.52
3.78
7.25
3.99
-2
8.28
3.63
8.00
3.85
7.73
4.06
2
10.07
3.80
9.66
4.04
9.25
4.28
6
14.21
4.09
13.80
4.37
13.32
4.64
10
15.46
4.31
15.04
4.61
14.63
4.93
15
16.70
4.50
16.28
4.85
15.87
5.16
20
17.60
4.63
17.18
5.03
16.70
5.42
* the above chat includes the weighted deicing infleuence.
LEGEND
TH
PI
WB
DB
ID
OD
5.2.3
–
–
–
–
–
–
Total Heating Capacity, kW
Power Input, kW
Wet Bulb Temp., (oC)
Dry Bulb Temp., (oC)
Indoor
Outdoor
Capacity Correction Factor Due to Tubing Length
Cooling
TOTAL TUBING LENGTH
3m
7.5m
10m
15m
20m
25m
30m
40m
50m
1.02
1
0.98
0.97
0.96
0.95
0.93
0.92
0.91
* Minimum recommended tubing length between indoor and outdoor units is 3m.
Heating
TOTAL TUBING LENGTH
3m
7.5m
10m
15m
20m
25m
30m
40m
50m
1.03
1
0.99
0.97
0.95
0.94
0.93
0.92
0.92
* Minimum recommended tubing length between indoor and outdoor units is 3m.
SM SAFRPM 1-A.0 GB
5-4
CONTENTS
PERFORMANCE DATA & PRESSURE CURVES
5.3
SAF045 / GC 45 R22
5.3.1
Cooling Mode at 7.5m Tubing Connection.
230V : Indoor Fan at High Speed.
Entering Air DB
OD Coil (oC)
15
(1)
(1)
20
25
30
35
40
46
Data
Entering Air WB/DB ID Coil (oC)
15/21
17/24
19/27
21/29
23/32
TC
13.49
13.97
14.30
14.64
14.86
SC
9.55
9.96
10.34
10.60
10.80
PI
3.23
3.24
3.25
3.25
3.27
TC
13.05
13.76
14.19
14.53
14.84
SC
9.36
9.87
10.28
10.57
10.77
PI
3.51
3.52
3.53
3.55
3.56
TC
12.35
13.33
14.02
14.44
14.80
SC
9.12
9.67
10.20
10.50
10.69
PI
3.79
3.82
3.85
3.87
3.90
TC
11.55
12.58
13.59
14.07
14.49
SC
8.83
9.39
9.98
10.27
10.47
PI
4.09
4.15
4.19
4.22
4.26
TC
10.69
11.60
12.80
13.44
14.08
SC
8.40
9.00
9.75
10.03
10.23
PI
4.41
4.49
4.56
4.59
4.62
TC
9.72
10.59
11.55
12.63
13.28
SC
7.92
8.52
9.22
9.52
9.71
PI
4.76
4.83
4.92
4.98
5.03
TC
8.44
9.22
10.14
11.21
12.08
SC
7.29
7.81
8.41
8.70
8.90
PI
5.20
5.28
5.40
5.48
5.54
LEGEND
TC
SC
PI
WB
DB
ID
OD
–
–
–
–
–
–
–
Total Cooling Capacity, kW
Sensible Capacity, kW
Power Input, kW
Wet Bulb Temp., (oC)
Dry Bulb Temp., (oC)
Indoor
Outdoor
(1) Marked area is below standard operating limits. For operating in low ambient
conditions, Optional Accessories are needed.
SM SAFRPM 1-A.0 GB
5-5
CONTENTS
PERFORMANCE DATA & PRESSURE CURVES
5.3.2
Heating Mode at 7.5m Tubing Connection.
230V : Indoor Fan at High Speed.
ENTERING AIR DB ID COIL)O C)
15
20
25
ENTERING WB OD
COIL)o C)
TH
Pl
TH
Pl
TH
Pl
-10
8.09
4.10
7.78
4.36
7.47
4.58
-7
8.70
4.20
8.39
4.43
8.09
4.67
-2
9.24
4.25
8.93
4.51
8.62
4.76
2
11.24
4.45
10.78
4.74
10.32
5.02
6
15.86
4.79
15.40
5.12
14.86
5.44
10
17.25
5.05
16.79
5.40
16.32
5.78
15
18.63
5.27
18.17
5.68
17.71
6.04
20
19.64
5.43
19.17
5.89
18.63
6.35
* the above chat includes the weighted deicing infleuence.
LEGEND
TH
PI
WB
DB
ID
OD
5.3.3
–
–
–
–
–
–
Total Heating Capacity, kW
Power Input, kW
Wet Bulb Temp., (oC)
Dry Bulb Temp., (oC)
Indoor
Outdoor
Capacity Correction Factor Due to Tubing Length
Cooling
TOTAL TUBING LENGTH
3m
7.5m
10m
15m
20m
25m
30m
40m
50m
1.01
1
0.97
0.96
0.94
0.93
0.9
0.85
0.81
* Minimum recommended tubing length between indoor and outdoor units is 3m.
Heating
TOTAL TUBING LENGTH
3m
7.5m
10m
15m
20m
25m
30m
40m
50m
1.02
1
0.99
0.98
0.97
0.97
0.95
0.93
0.92
* Minimum recommended tubing length between indoor and outdoor units is 3m.
SM SAFRPM 1-A.0 GB
5-6
CONTENTS
PERFORMANCE DATA & PRESSURE CURVES
5.4
Pressure Curves: SAF024 / OU7-24 Z R410A
5.4.1
Cooling.
Discharge Pressure (Bar[g])
Discharge Pressure VS.Outdoor Temp
40
38
36
34
32
30
28
26
24
22
20
18
16
:%'%|&
:%'%|&
:%'%|&
:%'%|&
:%'%|&
15
20
25
30
35
Outdoor Temp.(DB oC )
40
46
40
46
Suction Pressure VS.Outdoor Temp
Suction Pressure (Bar[g])
12.0
:%'%|&
:%'%|&
:%'%|&
:%'%|&
:%'%|&
11.0
10.0
9.0
8.0
7.0
6.0
15
20
25
30
35
Outdoor Temp.(DB oC )
SM SAFRPM 1-A.0 GB
5-7
CONTENTS
PERFORMANCE DATA & PRESSURE CURVES
5.4.2
Heating.
Discharge Pressure(Bar[g])
Discharge Pressure VS.Outdoor Temp
40
38
36
34
32
30
28
26
24
22
20
18
16
'%|&
'%|&
'%|&
-10
-5
0
5
10
Outdoor Temp.( WB oC )
15
20
Suction Pressure VS.Outdoor Temp
Suction Pressure(Bar[g])
11.0
10.0
9.0
8.0
7.0
'%|&
'%|&
'%|&
6.0
5.0
4.0
3.0
-10
-5
0
5
10
Outdoor Temp.( WB oC )
15
20
SM SAFRPM 1-A.0 GB
5-8
CONTENTS
PERFORMANCE DATA & PRESSURE CURVES
5.5
Pressure Curves: SAF045 / OU10-47T R410A
5.5.1
Cooling.
Discharge Pressure (Bar[g])
Discharge Pressure VS.Outdoor Temp
40
38
36
34
32
30
28
26
24
22
20
18
16
:%'%|&
:%'%|&
:%'%|&
:%'%|&
:%'%|&
15
20
25
30
35
Outdoor Temp.(DB oC )
40
46
40
46
Suction Pressure VS.Outdoor Temp
Suction Pressure (Bar[g])
12.0
:%'%|&
:%'%|&
:%'%|&
:%'%|&
:%'%|&
11.0
10.0
9.0
8.0
7.0
6.0
15
20
25
30
35
Outdoor Temp.(DB oC )
SM SAFRPM 1-A.0 GB
5-9
CONTENTS
PERFORMANCE DATA & PRESSURE CURVES
5.5.2
Heating.
Discharge Pressure(Bar[g])
Discharge Pressure VS.Outdoor Temp
40
38
36
34
32
30
28
26
24
22
20
18
16
'%|&
'%|&
'%|&
-10
-5
0
5
10
Outdoor Temp.( WB oC )
15
20
Suction Pressure VS.Outdoor Temp
Suction Pressure(Bar[g])
11.0
10.0
9.0
8.0
7.0
'%|&
'%|&
'%|&
6.0
5.0
4.0
3.0
-10
-5
0
5
10
Outdoor Temp.( WB oC )
15
20
SM SAFRPM 1-A.0 GB
5-10
CONTENTS
PERFORMANCE DATA & PRESSURE CURVES
5.6
Pressure Curves: SAF045 / GC 45 R22
5.6.1
Cooling.
Discharge Pressure VS.Outdoor Temp
Discharge Pressure (Bar[g])
30
:%'%|&
:%'%|&
:%'%|&
:%'%|&
:%'%|&
28
26
24
22
20
18
16
14
12
10
8 15
20
25
30
35
40
46
40
46
Outdoor Temp.(DB oC )
Suction Pressure (Bar[g])
Suction Pressure VS.Outdoor Temp
:%'%|&
:%'%|&
:%'%|&
:%'%|&
:%'%|&
4.5
15
20
25
30
35
3.5
2.5
Outdoor Temp.(DB oC )
SM SAFRPM 1-A.0 GB
5-11
CONTENTS
PERFORMANCE DATA & PRESSURE CURVES
5.6.2
Heating.
Discharge Pressure VS.Outdoor Temp
Discharge Pressure(Bar[g])
24
22
20
18
'%|&
'%|&
'%|&
16
14
-10
-5
12
0
5
10
15
20
Outdoor Temp.( WB oC )
Suction Pressure VS.Outdoor Temp
Suction Pressure(Bar[g])
6.0
5.0
4.0
3.0
-10
-5
0
5
10
15
'%|&
'%|&
'%|&
20
2.0
Outdoor Temp.( WB oC )
SM SAFRPM 1-A.0 GB
5-12
CONTENTS
SOUND LEVEL CHARACTERISTICS
6.
SOUND LEVEL CHARACTERISTICS
6.1
Sound Pressure Level
Figure 1
6.2
Sound Pressure Level Spectrum (Measured as Figure 1)
SAF045
-70NC
-60NC
-50NC
-40NC
-30NC
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
-20NC
MICRO BAR0.002 dB re , OCTAVE BAND SOUND PRESSURE LEVEL
MICRO BAR0.002 dB re , OCTAVE BAND SOUND PRESSURE LEVEL
SAF024
Hz, BAND CENTER FREQUENCIES
FAN SPEED
-70NC
-60NC
-50NC
-40NC
-30NC
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
-20NC
Hz, BAND CENTER FREQUENCIES
LINE
HI
ME
LO
SM SAFRPM 1-A.0 GB
6-1
CONTENTS
SOUND LEVEL CHARACTERISTICS
6.3
Outdoor units
Unit
1m
Mic.
Ground
Figure 2
6.4
Sound Pressure Level Spectrum (Measured as Figure 2)
OU7-24 Z Heating
-70NC
-60NC
-50NC
-40NC
-30NC
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
-20NC
MICRO BAR0.002 dB re , OCTAVE BAND SOUND PRESSURE LEVEL
MICRO BAR0.002 dB re , OCTAVE BAND SOUND PRESSURE LEVEL
OU7-24 Z Cooling
-70NC
-60NC
-50NC
-40NC
-30NC
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
-20NC
Hz, BAND CENTER FREQUENCIES
Hz, BAND CENTER FREQUENCIES
OU10-47T Cooling
OU10-47T Heating
SM SAFRPM 1-A.0 GB
6-2
CONTENTS
WIRING DIAGRAMS
7.
WIRING DIAGRAMS
7.1
Indoor Units: SAF024, SAF045
SM SAFRPM 1-A.0 GB
7-1
CONTENTS
WIRING DIAGRAMS
7.2
Indoor Unit: OU7-24 Z R410A
SM SAFRPM 1-A.0 GB
7-2
CONTENTS
WIRING DIAGRAMS
7.3
Indoor Unit: OU10-47T R410A
SM SAFRPM 1-A.0 GB
7-3
CONTENTS
WIRING DIAGRAMS
7.4
Outdoor Unit: GC 45 R22
SM SAFRPM 1-A.0 GB
7-4
CONTENTS
WIRING DIAGRAMS
7.5
Connections between indoor unit and outdoor unit
SAF 24
SAF 45
Note: 1. ─ ─ ─ ─ Connection only for heat pump model
2.
*
Option, Power supply from outdoor or indoor unit
SM SAFRPM 1-A.0 GB
7-5
CONTENTS
ELECTRICAL DATA
8.
ELECTRICAL DATA
8.1
SAF024, SAF045
Note: Power wiring cord should comply with local laws and electrical regulations requirementsl.
SM SAFRPM 1-A.0 GB
8-1
CONTENTS
REFRIGERATION DIAGRAMS
9.
REFRIGERATION DIAGRAMS
9.1
SAF024 / OU7-24Z R410A
OUTDOOR UNIT
INDOOR UNIT
Service
port
Reverse
valve
Capillary
tube
Outdoor coil
Sensor
Compressor
Sensor
Strainer
Valves
Flared
connection
Capillary
tube
Indoor coil
Check
valve
Strainer
COOLING MODE
OUTDOOR UNIT
INDOOR UNIT
Service
port
Sensor
Compressor
Sensor
Reverse
valve
Valves
Flared
connection
Capillary
tube
Capillary
tube
Outdoor coil
Strainer
Indoor coil
Check
valve
Strainer
HEATING MODE
SM SAFRPM 1-A.0 GB
9-1
CONTENTS
REGRIGERATION DIAGRAMS
9.2
SAF045 / OU10-47T R410A
SM SAFRPM 1-A.0 GB
9-2
CONTENTS
REFRIGERATION DIAGRAMS
9.3
SAF045 / GC 45 R22
SM SAFRPM 1-A.0 GB
9-3
CONTENTS
TUBING CONNECTIONS
10.
TUBING CONNECTIONS
TUBE (Inch)
¼”
⅜”
½”
⅝”
¾”
11-13
13-20
11-13
40-45
13-20
11-13
60-65
18-25
11-13
70-75
18-25
11-13
80-85
40-50
11-13
TORQUE (Nm)
Flare Nuts
Valve Cap
Service Port Cap
1.
2.
3.
4.
5.
6.
7.
8.
Valve Protection Cap-end
Refrigerant Valve Port (use Allen wrench to open/close)
Valve Protection Cap
Refrigerant Valve
Service Port Cap
Flare Nut
Unit Back Side
Copper Tube
When the outdoor unit is installed above the indoor unit an oil trap is required every 5m along
the suction line at the lowest point of the riser. Incase the indoor unit is installed above the
outdoor, no trap is required.
SM SAFRPM 1-A.0 GB
10-1
CONTENTS
CONTROL SYSTEM
11.
CONTROL SYSTEM
11.1
SAFETY CONTROL
11.1.1
Time delay safety control
a. 3 minutes delay for compressor—the compressor is ceased for 3 minutes to balance the
pressure in the refrigenration cycle in order to protect the compressor.
b. 2 minutes delay for 4-way valve—The 4-way valve is ceased for 2 minutes to prevent the
refrigenrant-gas abnormal noise when the HEATING operation is OFF or switch to the other operation
mode.
11.1.2
Indoor pipe temperature sensor frost prevention control
When the indoor pipe temperature sensor reads 0OCor below for 5 minutes, the indoor pipe temperature
sensor frost prevention control starts. The compressor and outdoor fan stop and the indoor fan operates
at high speed for 3 minutes. After that, if the indoor pipe temperature sensor reads less than 5OC this
control prolonged until the indoor pipe temperature sensor reads 5OC or more.
11.1.3
High temperature protection control
During HEATING operation, the outdoor fan motor and compressor are controlled by the indoor pipe
temperature to prevent the high temperature of compressor.
Outdoor fan OFF: when the indoor pipe temperature is ≥53OC Outdoor fan ON: when the indoor pipe
temperature is ≤48OC Compressor OFF: when the indoor pipe temperature is ≥62OC Compressor ON:
when the indoor pipe temperature is ≤48OC
11.2
“I Feel” Model Operation
11.2.1
When the “I Feel” mode is selected,
the operation mode and initial set temperature are determined by the initial room temperature at startup of the operation except to turn off the air conditioner and operates it again.
11.2.2
If the mode is change to “I Feel” mode form other mode,
the “I Feel” mode doesn’t operate until compressor stop for more than 3 minutes
In the “I Feel” mode, when the controller receives the up or down single of temperature, the set
temperature can adjust by 1OC upper or lower. The biggest you can adjust by 2OC upper or lower.
11.3
“COOLING” Mode Operation
11.3.1
When the COOLING mode is selected without setting temperature,
the system will set the set temperature at 26OC automatically with the AUTO FAN speed.
11.3.2 When selecting the COOLING mode operation,
the system will operate according to the setting by the remote controller and the operation is as
following:
SM SAFRPM 1-A.0 GB
11-1
CONTENTS
CONTROL SYSTEM
11.4
“DRY” Mode Operation
1.4.1
The system for DRY operation used the same refrigerant circle as the cooling
circle.
12.4.2
When the system operates in DRY mode,
at first it operates in cooling mode at 16OC or 18OC for 3 minutes. And then, the system operates in
cooling mode with low speed that regards the temperature of the room temperature sensor reads
decrease 2OC as the set temperature. During the course of this, the fan speed set operation is failing
but the vane motor can be controlled.
11.5 “HEATING” Mode Operation (Only available for Heat Pump)
11.5.1
When the HEATING mode is selected without setting temperature,
the system will set the temperature at 23OCautomatically with the AUTO FAN speed.
11.5.2
When selecting the HEATING mode operation,
the system will operate according to the setting by the remote controller and the operation is as
following:
11.5.3
In HEATING mode,
the indoor fan motor speed is controlled by Cold Air Prevention Control.
11.5.4
Cold Air Prevention Control
a. The function is intend to prevent cold air from being discharged when the heating operation
starts or when defrosting.
b. The indoor fan speed will be controlled as following.
c. The vane angle is at the angle C(100ο) .
d. During the heating operation, if the compressor stops that it will adjust the indoor
fan speed, after 30 seconds to stop the fan.
SM SAFRPM 1-A.0 GB
11-2
CONTENTS
CONTROL SYSTEM
11.5.5
Defrost
Defrosting of the outdoor heat exchange is controlled by the microprocessor with detection by the
indoor pipe temperature sensor.
Defrost control type is according to the JC on the PCB whether is connected.
1. When the JC is connect on the PCB
When one of the conditions of A, Band C is satisfy, the defrosting operation stars.
In the condition A, it must satisfy the condition a),b) and c) then into defrosting operation.
a) IPT1 satisfy IPT1=IPTMAX- ΔIPT (8OC)
b) t5≥50 minutes (the compressor cumulative operation time ≥50minutes, t5 is permitted move
and lower than t1 too).
c) IPT <40OC, and keep 2 minutes.
According to the condition A enter the defrosting operation, the first defrosting operation time is
8minutes; After defrosting operation one cycle, and then judge and regulate the defrosting operation
time.
SM SAFRPM 1-A.0 GB
11-3
CONTENTS
CONTROL SYSTEM
B. After the compressor cumulative operation time exceeds 120 minutes and the temperature of
the IPT is less then 35OC for 2 minutes. When the defrosting operation time on this condition
exceeds 8minutes, it will terminate.
C. After the compressor operation continuously for 20 minutes and the IPT is less than 23OC or
from the last time of defrosting operation is 50 minutes or more intervals. When the defrosting
operation time on this condition exceeds 10 minutes, it will terminal.
2. When the JC isn’t connected on the PCB
When the conditions of a) or b) is satisfy, the defrosting operation starts.
a) Have the outdoor sensor on the outdoor unit: Under the heating operation, the compressor
cumulative operation time exceeds 50minutes and the temperature of the outdoor pipe temperature
sensor reads lower than -4OC
b) No the outdoor on the outdoor unit: Under the heating operation, the compressor cumulative
operation time exceeds 50 minutes, if the indoor pipe temperature sensor reads lower than 40OC
continuously for 2minutes.
3. Defrost terminating conditions
When the condition c) or d) is satisfy, the defrosting operation will terminal.
c) The outdoor defrost sensor reads 15OC or more.
d) The defrosting time exceeds 10 minutes.
11.6
“FAN” mode operation
The indoor fan motor always turns on at the set speed and the vane motor turns on at
the set fettle.
11.7
4-way valve control
SM SAFRPM 1-A.0 GB
11-4
CONTENTS
CONTROL SYSTEM
11.8
“SLEEP” mode
When the SLEEP button is pressed, the SLEEP mode is selected as following:
1. The indoor fan speed is set at the low speed, the power lamp and the sleep lamp is on, the
temperature off after 5 minutes.
2. When selecting COOLING/DRY operation with SLEEP mode, the set temperature will be raised by
1OC 1 hour later and 2OC 2 hour later.
3. When selecting HEATING operation with SLEEP mode, the set temperature will be dropped by 1OC
1 hour later and 2OC 2 hour later.
4. After the system operates in SLEEP mode for 8 hours, it will stop automatically.
11.9
Fan motor control
(1) Rotational frequency feedback control
The indoor fan motor is equipped with a rotational frequency sensor, and outputs signal to the
microprocessor to feedback the rotational frequency. Comparing the current rotational frequency with
the target rotational frequency, the microprocessor adjusts fan motor electric to make the current
rotational frequency close to the target rotational frequency. With this control, when the fan speed is
switched, the rotational frequency changes smoothly.
(2) When the rotational frequency feedback signal has not output for 5 seconds (or when the
microprocessor can’t detect the signal for 5 seconds), the fan motor is regarded locked-up. Then the
electric current to the fan motor is shut off. 10 second later, the electric current is applied to the fan
motor again. During the fan motor lock-up, the POWER indicator lamp flashes on and off 6 times/cycle
or E6 to show the fan motor abnormality.
11.10 Auto fan speed control
11.10.1
When the auto fan speed is selected,
the indoor fan motor speed is automatically controlled by the room temperature and the set
temperature.
11.10.2
In COOLING mode,
the indoor fan motor operates as following:
Fan Speed
11.10.3
In HEATING mode, the indoor fan motor operates as following:
Fan Speed
11.11
Auto vane operation control
11.11.1
Vane motor drive
The unit is equipped with a stepping motor for the vane. The rotating direction, speed, and angle of the
motor are controlled by pulse signal transmitted from indoor microprocessor.
SM SAFRPM 1-A.0 GB
11-5
CONTENTS
CONTROL SYSTEM
11.11.2
Positioning
The vane is once pressed to the cane stopper below to confirm the standard position and then set to
the desired angle. The positioning is decided as follows:
a. When the ON/OFF button is pressed.
b. When the vane control is change from AUTO to MANUAL.
c. When the SWING is finished.
d. When the test run starts.
e. When the power supply turns ON.
11.11.3
The auto vane changes as follows by pressing the VANE CONTROL button.
11.11.4
VANE AUTO mode
In vane auto mode, the microprocessor automatically determines the vane angle and operation
to make the optimum room-temperature distribution.
11.11.5
SWING mode
When presses the SWING button, the vane swings.
11.12
TIMER Operation
11.12.1
To activate the air conditioner at the desire time,
follow the procedure specified below(the remote control and air conditioner are switched off):
a. Press the TIMER button
b. Select the desired mode by pressing the mode button.
c. Select the desired temperature by pressing the UP/DOWN button (only possible when the ‘cool’
or ‘heat’ mode is selected).
d. Select the ventilator speed (low, medium or high) or automatic mode (only possible
when the feel, COOL or HEAT mode is selected) by pressing the Fan button. The ventilator always
operates in the auto mode when the dry mode is selected.
e. Select swing or no swing by pressing the SWING button
f. Press the TIMER button (‘h’ flashes ).
g. Use the UP/DOWN button to select the time at which the air conditioner must activate
(between 0 and 10 hours can be set at every half hour-between 10 and 24 hours can be set at every
hour).
h. Press the TIME button (‘h’ stops flashing) and the preset time appears in the display.
i. Press the TIME button again to delete the selected data from the memory.
Note: if no buttons are pressed during the programming of the timer function, thee remote control will
switch off automatically after 10 seconds.
11.12.2
To switch the air conditioner off at the desired time,
follow the procedure specified below (the remote control and air conditioner are switched off):
a. Press the timer button.
b. Use the UP/DOWN button to select the time at witch.
11.13
Emergency Operation
When the EMERGENCY operation switch is pressed once, COOLING mode is selected and if in
3 seconds the emergency operation switch is pressed again, mode is selected. Then pressed once
again, the unit is switch off.
When the remote controller is missing, has failed or the batteries run down, press the EMERGENCY
operation switch on the front of the indoor unit. The unit will start. The first 30 minutes of operation
will be the test run operation. The operation is for servicing. The indoor fan runs at high speed and
the system is in continuous operation.
SM SAFRPM 1-A.0 GB
11-6
CONTENTS
CONTROL SYSTEM
The thermostat is ON and timer is reset to normal.
After 30 minutes of test run operation the system shifts to AUTO COOLING/Heating mode, and the
indoor fan runs in automatic speed. The operation continues unit the EMERGENCY operation switch
is pressed or a button on the remote controller is pressed, the normal operation will start.
Note: Do not press the EMERGEMCY operation switch during normal operation.
11.14
AUTO RESTART Function (Option)
11.14.1
When the indoor unit is controlled with the remote controller,
the operation mode, set temperature, and the fan speed are memorized by the indoor electric control
PCB. The AUTO RESTART function sets to work the moment power has restored after power failure.
Then, the unit will restart automatically.
11.14.2
How to set the AUTO RESTART function.
a. Press the emergency switch and power supply to the PCB following, keep 10seconds and the
buzzer will beep three times. The AUTO-RESTART is set.
b. Do the operation again, the buzzer will beep four times and the AUTO-RESTART function is
cancelled.
11.15
Electron lock function
Press the fan button for 5 seconds, the buzzer beep one sound. The all button is invalidation for operate
the air conditioner except the remote controller.
11.16
Failure Display and handling
11.16.1
Failure Display
When the controller is failure, the buzzer will voice long for three times, and displays the failure from the
failure lamp.
11.16.2
Failure Code
If there is the digital pipe that display the failure code for digital pipe, or display for the fun lamp.
12.16.3
Failure Handling
a. When the room temperature sensor or the indoor pipe temperature sensor is failure,
the system will be shut off, the compressor will be OFF, and the outdoor fan and the indoor fan will
be OFF. The system doesn’t receive the signal of remoter controller except the signal of shut off
it. When the failure disappeared, the controller can operate in normal mode. Before this, presses
the “ON/OFF” to start the system, and it will operate in COOLING or HEATING for 30minutes, and
follows shut off. During this, it displays the failure and the protection is failing. You must be given the
electric again to operate it. In the failure, you can operate the fan mode.
b. When the outdoor protects in the COOLING or DRY, the outdoor unit stops, the
indoor fan operates in set speed; and in the HEATING, the outdoor unit stops, the indoor fan operates
in cold air prevention control. The system doesn’t receive the signal of remoter controller except the
signal of shut off it. When the system check the voltage is 220V and the delay control is finished, it
operates at normal again.
c. When the indoor fan motor is failure, the compressor is stopped, the outdoor fan
and indoor fan is stopped and display the failure. The system doesn’t receive the signal of remoter
controller except the signal of shut off it.
SM SAFRPM 1-A.0 GB
11-7
CONTENTS
CONTROL SYSTEM
11.16.4
Display of the control
In the display board the lamp from left is the POWER lamp (Red), the SLEEP lamp (Yellow), the TIMER
lamp (Yellow), the RUN lamp (Green)
11.16.5
When gives the control electric,
the buzzer voices a long for 0.3 second per cycle.
12.17
Control logic for the heater
The control logic for the heater is as follows:
Condition to Cut in:
If all following conditions are satisfied, the heater can operate:
1. The running time for the compressor exceeds 10 seconds.
2. The normal running time for the IDU Fan exceeds 15 seconds.
3. Not available in deicing mode.
4. Exceed 30 seconds without heater operation.
5. ST-RT≥3OC
6. RT<22OC
7. ICT≤43OC
Condition to Cut off
If any following condition is satisfied, the heater will be off power:
1. The compressor is power off.
2. RT≥24OC
3. ICT≥48OC
4. The IDU Fan is not running
5. Entering into sleep mode.
SM SAFRPM 1-A.0 GB
11-8
CONTENTS
TROUBLESHOOTING
12.
TROUBLESHOOTING
Trouble
Analysis
If the protector trips or fuse is blown.
?
Does not run
If the leakage breaker trips.
If the plug loosened.
Sometimes it stops working to protect the
appliance.
Is the air filter dirty?
Are the intakes and outlets of the air
conditioner blocked?
Not cool or warm
enough
Is the temperature set properly?
?
Ineffective control
Does not operate
immediately
?
Do not
operate
If strong interference (from excessive static
electricity discharge, power supply voltage
abnormality) presents, sometimes operation
will be affected. In this case, switch off the
breaker and switch on it again 2~3 seconds later.
Shifting to other modes during operation, wait 3
minutes to start.
Peculiar odor
Odor may come from sources such as furniture
or cigarette and blown out by the unit.
A sound of
running-water
Caused by the flow of refrigerant inside
the air conditioner, not a failure.
A"pi-pa" sound can be
heard
Caused by the expansion or contraction of
the internal components due to temperature
changes. That is not a failure.
Blow mist from
the outlet
Room air is cooled down by the cold air blown
out from the unit and mist thus form during
"COOLING" or "DRY" mode when humidity is
too high inside.
SM SAFRPM 1-A.0 GB
12-1
CONTENTS
EXPLODED VIEWS & SPARE PARTS LISTS
13.
EXPLODED VIEWS & SPARE PARTS LISTS
13.1
Indoor Unit: SAF024
SM SAFRPM 1-A.0 GB
13-1
CONTENTS
EXPLODED VIEWS & SPARE PARTS LISTS
13.2
No.
Indoor Unit: SAF024
Items
Description
Quantity
1
1070710042
Inside Base
1
2
1210520504
Right Plate
1
3
1210710130
Back Plate
1
4
1200710102
Rubber Water Drainage
1
5
1210520503
Left Plate
1
6
1300710366
Evaporator
1
7
1210520113
Top Plate
1
8
1071200043
Pipe Cover
1
9
1090020038
Heater(Option)
1
10
1150520103
Water Drainage
1
11
1150720004
Out Blow Casing Foam
1
12
1150720005
Heat insulation board
1
13
1070520106
Vertical Vane
1
14
1170010008
Synchronization Motor
1
15
1070520530
Horizontal Vane
1
16
1300710361
Up Panel(ARIWELL)
1
16
1300710373
Up Panel(ELECTRA)
1
17
1080520103
Middle Supporter
1
18
1080710302
Heat insulation board Cover
1
19
1090520136
Display PCB
1
20
1070710422
Display PCB Supporter
1
21
1070710014
Display PCB Cover
1
22
1070710424
Spring
1
23
1070710423
Button
1
24
1020710010
Ornamental Board
1
25
1300710364
Down panel
1
26
1070520149
FastEner
1
27
1070520147
Air Filter
1
28
1170230025
Indoor Sensor
1
29
1074060115
Lead Flow Circle
1
30
1080520106
Inside Elactrical Box Cover
1
31
1070010008
Centrifugal Fan
1
32
1170240002
Transformer
1
33
1170050002
Indoor Motor
1
34
1170100056
Fan Motor Capacitor
1
35
1170200079
Terminal
1
36
1090710148
Main PCB(With heater)
1
36
1090710713
Main PCB(Without heater)
1
37
1070520318
Volute Casing
1
38
1080520105
Inside Electrical Box
1
39
1070210005
Anions Generator(Option)
1
40
1090050450
Remote Controller(AIRWELL)
1
40
1090050452
Remote Controller(ELECTRA)
1
SM SAFRPM 1-A.0 GB
13-2
CONTENTS
EXPLODED VIEWS & SPARE PARTS LISTS
13.3
Indoor Unit: SAF045
SM SAFRPM 1-A.0 GB
13-3
CONTENTS
EXPLODED VIEWS & SPARE PARTS LISTS
13.4
No.
Indoor Unit: SAF045
Items
Description
Quantity
1
1301200262
Inside Base
1
2
1081200126
Right Plate
1
3
1081200103
Back Plate
1
4
1204090101
Rubber Water Drainage
1
5
1081200127
Left Plate
1
6
1110050960
Evaporator
1
7
1301200261
Top Plate
1
8
1071200043
Pipe Cover
1
9
1090020038
Heater(Option)
1
10
1154090101
Water Drainage
1
11
1151200001
Out Blow Casing Foam
1
12
1214090113
Heat insulation board
1
13
1071200014
Vertical Vane
1
14
1170010008
Synchronization Motor
1
15
1071200073
Horizontal Vane
1
16
1301200259
Up Panel(AIRWELL)
1
16
1301200272
Up Panel(ELECTRA)
1
17
1084090101
Middle Supporter
1
18
1090520136
Display PCB
1
19
1070710422
Display PCB Supporter
1
20
1070710416
Display PCB Cover
1
21
1070710424
Spring
1
22
1070710423
Button
1
23
1020710010
Ornamental Board
1
24
1071200069
Down panel
1
25
1070520149
Fastener
1
26
1070300003
Air Filter
1
27
1170230025
Indoor Sensor
1
28
1074090102
Lead Flow Circle
1
29
1084090113
Inside Elactrical Box Cover
1
30
1070010004
Centrifugal Fan
1
31
1170240002
Transformer
1
32
1170030010
Indoor Motor
1
33
1170100057
Fan Motor Capacitor
1
34
1170200079
Terminal
1
35
1090710148
Main PCB (With heater)
1
35
1090710173
Main PCB (Without heater)
1
36
1154090102
Volute Casing
1
37
1084090112
Inside Electrical Box
1
38
1070210005
Anions Generator(Option)
1
39
1090050450
Remote Controller(AIRWELL)
1
39
1090010452
Remote Controller(ELECTRA)
1
SM SAFRPM 1-A.0 GB
13-4
CONTENTS
EXPLODED VIEWS & SPARE PARTS LISTS
13.5
Outdoor Unit: OU7-24 Z
*Optional
20
18
44
17
24
19a
SM SAFRPM 1-A.0 GB
13-5
CONTENTS
EXPLODED VIEWS & SPARE PARTS LISTS
13.6
No.
Outdoor Unit: OU7-24 Z
Item
Description
Quant
1
437045
LARGE UPPER COVER CUE
1
2
433280
SIDE PANEL OU7-24 R410A
1
3
436357
SMALL ELECTRICAL COVER
1
4
439329
COVERAIR COLLECTOR
1
5
437091
OU SQUARE FAN GUARD
1
6
433722
NEW BASE ASSY OU7-24C EXPORT R410A
1
7
433285
COIL OU7-24 HDR
1
8
4529604 AXIAL FAN D493*143
1
9
434211
REPLACE BY SP000000MOTOR+BRACKET
1
10
433281
SIDE GUADRO OU7-24 R410A
1
11
436358
TRANSPORT HANDLE CUE
1
12
439342
MOTOR SUPPORT OU7
1
14
438795
COMPRESSOR GP270PAA
1
15
433934
CAPILLARY HEATING ASSY OU7-24 R410A
1
16
433660
TUBING ASSY OU7-24Z R410A
1
17
413496
BOARD TPHN 5F (RoHS)
1
18
442007
CAPACITOR 6uF 400V P1/P2
1
19a
434716
THERMISTOR L1050 (for coil)
1
20
442038
CAPACITOR 50mF 400V P1/P2
1
21
437627
COMPRESOR WIRING TPHN-5F
1
24
437229
ELECTRICAL BOX TPHN
1
33
442520
VALVE COIL L700 MOLEX-DUMAN
1
44
192207
CONTACTOR 230V, 40A
1
SM SAFRPM 1-A.0 GB
13-6
CONTENTS
EXPLODED VIEWS & SPARE PARTS LISTS
13.7
Outdoor Unit: OU10-47T
SM SAFRPM 1-A.0 GB
13-7
CONTENTS
EXPLODED VIEWS & SPARE PARTS LISTS
13.8
Outdoor Unit: OU10-47T
SP No. Item
Description
Quantity
1
437045
UPPER COVER EL13 OU LARGE
1
2
417221
Side panel N OU10
1
3
436357
SMALL ELECTRICAL COVER OU
1
4
456714
FRONT PANEL OU10
1
5
439662
GRILLE OU10
2
6
439833
NEW BASE ASSY OU EXPORT
1
7
442712
COIL OU10-47 GR HDR 2R NEW R41
1
8
439650
AXIAL FAN D400*112 (COMMON)
2
9
439651
MOTOR 70W,3S,OU10-50
2
10
417223
Side net panel N OU10
1
11
436358
OU LEADING HANDLE
1
12
439657
MOTOR SUPPORT OU10
1
12b
414226
Motor support flange OU-10
1
12c
414229
Motor support clamp bracket OU
1
13
190443
HEATER CRANKCASE MITSUBISHI CO
1
14
438824
COMPRESSOR ZP54KSE-TFM
1
15
441107
CAPILLARY ASSY OU10-47Z
1
16
438957
Tubing Assembly OU10-47 EXPORT
1
17
438886
BOARD TPHN 3F/3G
1
18
434549
SERVICE VALVE ASSY 3/4F 3 WAY
1
18
442017
CAPACITOR 3mF 450V P1/P2
2
19a
434716
THERMISTOR+CAP WTH CONNECTOR L
1
19b
402741
THERMISTOR WTH CONNECTOR L1250
1
21
445320
COMPRESSOR WIRING WITHOUT PLUG
1
22
402284
SUCTION ACCUMULATOR 5" x 3/4"
1
23
439661
AIR OUTLET RING OU10
2
24
437229
ELECTRICAL BOX TPHN
1
26
436352
RAISING HANDLE OU10
1
28
439656
SIDE COVER OU-8/10
1
31
402165
TYPHOON BOX COVER
1
33
442466
VALVE COIL L700 MOLEX-SANHUA
1
65
416910
CABLE HOLDER
4
SM SAFRPM 1-A.0 GB
13-8
CONTENTS
EXPLODED VIEWS & SPARE PARTS LISTS
13.9
Outdoor Unit: GC 45 R22
SM SAFRPM 1-A.0 GB
13-9
CONTENTS
EXPLODED VIEWS & SPARE PARTS LISTS
13.10
Outdoor Unit: GC 45 R22
No.
Part No.
Description
Quantity
1
4517832
TOP COVER PAINT ASSY
1
2
4517144
FAN COVER PP+UV/GRILL A
2
3
4520871
BASE PLATE PAINT ASSY.
1
4
4522238
LEFT FRONT PANEL PAINTED ASSY.
1
5
4517834
RIGHT FRONT PANEL PAINT ASSY
1
6
4517772
LITTLE HANDLE
1
7
4521345
DIVIDING PLATE
1
8
4526128
SUPPORT FOR CONTROLLER PANEL
1
9
455000102
DOUBLE PATCH CAPACITOR FOR FAN MOTOR 3UF (CBB61S
2
10
4517782
AC CONTACTOR EB25 OR D2501N
1
11
4517006
TERMINAL BLOCK OF CABLE
1
12
4517308
TERMINAL BLOCK OF POWER SUPPLY
1
13
4517048
TERMINAL BLOCK OF NUETRAL
1
14
4517833
VALVE BASE PAINT ASSY
1
15
4517535
HIGH PRESSURE STOP VALAE
1
16
4517536
LOW PRESSURE STOP VALVE
1
17
4518602
COMPRESSOR CABLE
1
18
467470001
MIX AND MISSING PHASE DEVICE
1
19
4517743
COMPRESSOR ASSY JT160BCBY1L
1
20
4521286
ACCUMULATOR
1
21
4520854
DISCHARGE TUBE1 (12.7*0.7)
1
23
4517783
COMPR. JACKET
1
23
4518782
TOP COVER INSULATION FOR COMP
1
22
4520846
SUCTION TUBE 2 (19.05*1)
1
24
4520863
OIL SEPARATOR WELDING ASSY.
1
25
4520884
CONDENSING TUBE 2(WITH ACCESSORIES)
1
26
4525814
RIGHT-BACK PLATE PAINTED ASSY.
1
27
4519751
PRESSURE SWITCH(3.0MPA OFF/2.4MPA ON)
1
28
4520850
4-WAY VALVE WELDING ASSY.
1
29
4516429
OUT SENSOR BLACK
1
30
4521113
SINGLE-WAY AND FILTER WELDING ASSY.
1
31
C66037900
CONDENSER ASSY/LOWER/GC48
1
32
C65063600
MANIFOLD WELDING ASSY
1
33
4517576
CONDENSOR ASSEMBLY (UP)
1
34
4524731
BACK GRILLE PAINT ASSY
1
35
4525909
CONNECT PANEL ASSY
1
36
4517767
COMPR. SUB HEATER
1
38
4519199
MOTOR KICKSTAND
1
39
4517740R
MOTOR YYK60B-6
2
40
4517004
AXIAL FAN D=450MM
2
41
4523141
HEXAGON LOCKED NUT M10
2
42
C66038000
DISTRIBUTING CAPILLARY ASSY
1
SM SAFRPM 1-A.0 GB
13-10
CONTENTS
APPENDIX A
APPENDIX A
INSTALLATION AND OPERATION MANUAL
►
INSTALLATION & OPERATION MANUAL SAF024
►
INSTALLATION & OPERATION MANUAL SAF045
SM SAFRPM 1-A.0 GB
14-1
CONTENTS