Briggs & Stratton | 460000 | Owner`s manual | Briggs & Stratton 460000 Owner`s manual

Operating & Maintenance
Instructions
Model Series
Covered in
This Manual
420000
460000
Model
Type
Note: General Model Series number noted above is inclusive of the specific model
number found on your engine. To get replacement parts or technical assistance in
the future, write your engine Model, Type, Code and date of purchase here.
TABLE OF CONTENTS
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Engine Information . . . . . . . . . . . . . . . . . . . . . . . . 6
Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Fuel and Starting Information . . . . . . . . . . . . . . . 8
Starting and Stopping . . . . . . . . . . . . . . . . . . . 9-10
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 11-14
Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15
Parts and Service & Storage . . . . . . . . . . . . . . . 16
Warranty Information . . . . . . . . . . . . . . . . . . . . . 17
PRINTED IN U.S.A.
Document: - page 1 (Black)
Screen angle and frequency: 45.0000, 150.0000
Code
Month Day
Year
WARNING
Briggs & Stratton does not approve or authorize the use of
these engines on 3-wheel All Terrain Vehicles (ATVs), motor
bikes, aircraft products or vehicles intended for use in
competitive events. Use of these engines in such applications
could result in property damage, serious injury (including
paralysis), or even death.
Need assistance? Go to www.briggsandstratton.com
for detailed information regarding
Briggs & Stratton engines.
Or call, 1-800-233-3723, (U.S.A. and Canada)
to hear a menu of pre-recorded messages
offering engine maintenance information.
 Copyright 2003 by Briggs & Stratton Corporation
FORM NO. 274796-5/03
The Power That Works For You.
Look For Relevant Emissions Durability Period and Air Index Information On Your Engine Emissions Label
Engines that are certified to meet the California Air Resources Board (CARB) Tier 2 Emission Standards must
display information regarding the Emissions Durability Period and the Air Index. Briggs & Stratton makes this
information available to the consumer on our emission labels. The engine emission label will indicate certification
information.
The Emissions Durability Period describes the number of hours of actual running time for which the engine is
certified to be emissions compliant, assuming proper maintenance in accordance with the Operating &
Maintenance Instructions. The following categories are used:
Moderate:
Engine is certified to be emission compliant for 125 hours of actual engine running time.
Intermediate:
Engine is certified to be emission compliant for 250 hours of actual engine running time.
Extended:
Engine is certified to be emission compliant for 500 hours of actual engine running time.
For example, a typical walk-behind lawn mower is used 20 to 25 hours per year. Therefore, the Emissions
Durability Period of an engine with an intermediate rating would equate to 10 to 12 years.
The Air Index is a calculated number describing the relative level of emissions for a specific engine family. The
lower the Air Index, the cleaner the engine. This information is displayed in graphical form on the emissions
label.
After July 1, 2000, Look For Emissions Compliance Period On
Engine Emissions Compliance Label
After July 1, 2000 certain Briggs & Stratton engines will be certified to meet the United States Environmental
Protection Agency (USEPA) Phase 2 emission standards. For Phase 2 certified engines, the Emissions
Compliance Period referred to on the Emissions Compliance label indicates the number of operating hours for
which the engine has been shown to meet Federal emission requirements. For engines less than 225 cc
displacement, Category C = 125 hours, B = 250 hours and A = 500 hours. For engines of 225 cc or more,
Category C = 250 hours, B = 500 hours and A = 1000 hours.
The displacement of Model Series 420000 engines is 694 cc. The displacement of Model Series 460000 engines
is 745 cc.
2
Document: - page 2 (Black)
Screen angle and frequency: 45.0000, 150.0000
274796
BEFORE OPERATING ENGINE
• Read entire Operating & Maintenance Instructions AND
the instructions for the equipment this engine powers.*
• Failure to follow instructions could result in serious injury
or death.
THE OPERATING & MAINTENANCE INSTRUCTIONS
CONTAIN SAFETY INFORMATION TO
• Make you aware of hazards associated with engines
• Inform you of the risk of injury associated with those hazards, and
• Tell you how to avoid or reduce the risk of injury.
(
)
HAZARD SYMBOLS AND MEANINGS
The safety alert symbol
is used to identify safety
information about hazards that can result in personal injury.
A signal word (DANGER, WARNING, or CAUTION) is
used with the alert symbol to indicate the likelihood and the
potential severity of injury. In addition, a hazard symbol
may be used to represent the type of hazard.
Fire
Explosion
Moving Parts
DANGER indicates a hazard which, if not
avoided, will result in death or serious injury.
Toxic Fumes
Hot Surface
Shock
WARNING indicates a hazard which, if not
avoided, could result in death or serious injury.
Kickback
CAUTION indicates a hazard which, if not
avoided, might result in minor or moderate
injury.
THE INTERNATIONAL SYMBOLS USED
ON THE ENGINE OR
IN THIS MANUAL INCLUDE:
CAUTION, when used without the alert symbol,
indicates a situation that could result in damage
to the engine.
WARNING
Safety Alert
The engine exhaust from this product contains chemicals known to the
State of California to cause cancer,
birth defects, or other reproductive
harm.
*
Oil
Read Owner’s
Manual
Stop Fuel Shutoff Choke
On Off
Fuel
Briggs & Stratton does not necessarily know what equipment this engine will power. For that reason, you should carefully read
and understand the operating instructions for the equipment on which your engine is placed.
3
Document: - page 3 (Black)
Screen angle and frequency: 45.0000, 150.0000
SAFETY
WARNING
WARNING
Starting engine creates sparking.
Gasoline and its vapors are extremely
flammable and explosive.
Sparking can ignite nearby flammable
gases.
Fire or explosion can cause severe burns
or death.
Explosion and fire could result.
WHEN ADDING FUEL
• If there is natural or LP gas leakage in area, do not
start engine.
• Do not use pressurized starting fluids because
vapors are flammable.
• Turn engine OFF and let engine cool at least 2
minutes before removing gas cap.
• Fill fuel tank outdoors or in well-ventilated area.
• Do not overfill fuel tank. Fill tank to approximately
1-1/2 inches below top of neck to allow for fuel
expansion.
• Keep gasoline away from sparks, open flames,
pilot lights, heat, and other ignition sources.
• Check fuel lines, tank, cap, and fittings frequently
for cracks or leaks. Replace if necessary.
WARNING
Rapid retraction of starter cord (kickback) will
pull hand and arm toward engine faster than
you can let go.
WHEN STARTING ENGINE
• Make sure spark plug, muffler, fuel cap and air
cleaner are in place.
• Do not crank engine with spark plug removed.
• If fuel spills, wait until it evaporates before starting
engine.
• If engine floods, set choke to OPEN/RUN position,
place throttle in FAST and crank until engine starts.
Broken bones, fractures, bruises or sprains
could result.
• When starting engine, pull cord slowly until
resistance is felt, then pull rapidly.
• Remove all external equipment/engine loads
before starting engine.
• Direct coupled equipment components such as,
but not limited to, blades, impellors, pulleys,
sprockets, etc., must be securely attached.
WHEN OPERATING EQUIPMENT
• Do not tip engine or equipment at angle which
causes gasoline to spill.
• Do not choke carburetor to stop engine.
WHEN TRANSPORTING EQUIPMENT
WARNING
• Transport with fuel tank EMPTY or with fuel shut-off
valve OFF.
Rotating parts can contact or entangle
hands, feet, hair, clothing, or accessories.
WHEN STORING GASOLINE OR EQUIPMENT
WITH FUEL IN TANK
Traumatic amputation or severe laceration
can result.
• Store away from furnaces, stoves, water heaters or
other appliances that have pilot light or other
ignition source because they can ignite gasoline
vapors.
• Operate equipment with guards in place.
• Keep hands and feet away from rotating parts.
• Tie up long hair and remove jewelry.
• Do not wear loose-fitting clothing, dangling
drawstrings or items that could become caught.
4
Document: - page 4 (Black)
Screen angle and frequency: 45.0000, 150.0000
SAFETY
WARNING
WARNING
Engines give off carbon monoxide, an
odorless, colorless, poison gas.
Unintentional sparking can result in fire or
electric shock.
Breathing carbon monoxide can cause
nausea, fainting or death.
Unintentional start-up can result in entanglement, traumatic amputation, or laceration.
• Start and run engine outdoors.
• Do not start or run engine in enclosed area, even if
doors or windows are open.
BEFORE PERFORMING ADJUSTMENTS OR
REPAIRS
WARNING
• Disconnect spark plug wire and keep it away from
spark plug.
• Disconnect battery at negative terminal (only
engines with electric start).
Running engines produce heat. Engine
parts, especially muffler, become extremely
hot.
Severe thermal burns can occur on contact.
WHEN TESTING FOR SPARK
Combustible debris, such as leaves, grass,
brush, etc. can catch fire.
• Use approved spark plug tester.
• Do not check for spark with spark plug removed.
• Allow muffler, engine cylinder and fins to cool
before touching.
• Remove accumulated combustibles from muffler
area and cylinder area.
• Install and maintain in working order a spark
arrester before using equipment on forest-covered,
grass-covered, brush-covered unimproved land.
The state of California requires this (Section 4442
of the California Public Resources Code). Other
states may have similar laws. Federal laws apply
on federal land.
ENGINE INFORMATION
TECHNICAL INFORMATION
POWER RATINGS: The power ratings for an individual engine
model are initially developed by starting with SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque
Rating Procedure) (Revision 2002-05). Given both the wide array
of products on which our engines are placed, and the variety of environmental issues applicable to operating the equipment, it may
be that the engine you have purchased will not develop the rated
horsepower when used in a piece of power equipment (actual “onsite” power). This difference is due to a variety of factors including,
but not limited to, the following: differences in altitude, tempera-
ture, barometric pressure, humidity, fuel, engine lubrication, maximum governed engine speed, individual engine to engine variability, design of the particular piece of power equipment, the manner
in which the engine is operated, engine run-in to reduce friction
and clean out of combustion chambers, adjustments to the valves
and carburetor, and other factors. The power ratings may also be
adjusted based on comparisons to other similar engines utilized
in similar applications, and will therefore not necessarily match the
values derived using the foregoing codes.
5
Document: - page 5 (Black)
Screen angle and frequency: 45.0000, 150.0000
ENGINE INFORMATION
4
5
3
11
10
9
8
2
1
7
1.
2.
3.
4.
5.
Spark plug wire
Carburetor
Air cleaner
Rotating screen
Emission label and Engine
Model
Type
Code
label
xxxxxx
xxxx xx
xxxxxxxx
6.
7.
8.
9.
10.
11.
6
Oil drain plug
Crankshaft
12V electric starter
Fuel filter
Oil fill/Dipstick
Blower housing
GENERAL INFORMATION
TUNE-UP SPECIFICATIONS
ENGINE MODEL
Armature air gap . . . 0.010 – 0.014 in. (0.25 – 0.36 mm)
This is a twin cylinder, L-head, air-cooled engine. It is a low
emissions engine.
In the state of California, the 420000 and 460000 series
engines covered in this manual are certified by the
California Air Resources Board to meet emissions standards for 125 hours. Such certification does not grant the
purchaser, owner or operator of this engine any additional
warranties with respect to the performance or operational
life of this engine. This engine is warranted solely according
to the product and emissions warranties stated elsewhere
in this manual.
Spark plug gap . . . . . . . . . . . . . . . . . . 0.030 in. (0.76 mm)
Valve clearance with valve springs installed and piston 1/4 in.
(6 mm) past top dead center (check when engine is cold).
See Repair Manual P/N 271172.
Intake . . . . . . . . . . . . . 0.006 – 0.008 in. (0.15 – 0.20 mm)
Exhaust . . . . . . . . . . . 0.009 – 0.011 in. (0.23 – 0.28 mm)
Note: For practical operation, the horsepower loading
should not exceed 85% of rated horsepower. Engine power
will decrease 3-1/2% for each 1,000 feet (300 meters)
above sea level and 1% for each 10° F (5.6° C) above 77° F
(25° C). It will operate satisfactorily at an angle up to 15°.
MODEL SERIES 420000
Bore . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7/16 in. (87.31 mm)
Stroke . . . . . . . . . . . . . . . . . . . . . . . . 2-9/32 in. (57.94 mm)
Displacement . . . . . . . . . . . . . . . . 42.33 cu. in. (694.0 cc)
MODEL SERIES 460000
Bore . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9/16 in. (90.49 mm)
Stroke . . . . . . . . . . . . . . . . . . . . . . . . 2-9/32 in. (57.94 mm)
Displacement . . . . . . . . . . . . . . . . 45.48 cu. in. (745.2 cc)
6
Document: - page 6 (Black)
Screen angle and frequency: 45.0000, 150.0000
274796
OIL
SAE Viscosity Grades
CAUTION: This engine is shipped from Briggs &
Stratton without oil. Check oil level before starting
engine. If you start the engine without oil, the engine
will be damaged beyond repair and will not be
covered under warranty.
**
*
OIL CAPACITY
Engine without oil filter holds approximately 1-1/2 quarts
(48 ounces; 1.4 liter).
°F -20
°C -30
0
-20
20
-10
32
40
0
60
10
80
20
100
30
Engine equipped with oil filter holds approximately
1-3/4 quarts (56 ounces; 1.7 liters).
*
CAUTION: Use 5W-30 oil or synthetic oil if anticipated
temperatures are below 40° F (4° C) to prevent
internal engine damage at startup due to inadequate
lubrication. Air cooled engines run hotter than
automotive engines. The use of non-synthetic
multi-viscosity oils, e.g. 5W-30, in temperatures
above 40° F (4° C) will result in higher than normal oil
consumption. When using a multi-viscosity oil, check
oil level more frequently.
** CAUTION: SAE 30 oil, if used below 40° F (4° C), will
result in hard starting and possible engine bore
damage due to inadequate lubrication.
TYPE OF OIL TO USE
• Use a high quality detergent oil classified “For Service
SF, SG, SH, SJ” or higher, such as Briggs & Stratton
30W, Part Number 100005 (20 oz) or 100028 (48 oz).
• Do not use special additives.
• Choose a viscosity according to the table opposite.
Note: Synthetic oil meeting ILSAC GF-2, API
certification mark and API service symbol
(shown at left) with “SJ/CF ENERGY CONSERVING” or higher, is an acceptable oil at all
temperatures. Use of synthetic oil does not
alter required oil change intervals.
CHECKING AND ADDING OIL
• Check oil level before starting the engine.
• Check level daily, or after every eight (8) hours.
• Keep oil level at FULL.
• Do not overfill.
Dipstick
Oil Fill
[1]
Place engine level. Clean
around oil fill and dipstick.
[4]
Remove dipstick. Pour oil
slowly.
ÏÏ
[2]
Remove dipstick and wipe clean with cloth.
[3]
Then push dipstick back in and remove to check oil level.
[5]
FULL
Fill to FULL line on dipstick
– recheck.
7
Document: - page 7 (Black)
Screen angle and frequency: 45.0000, 150.0000
FULL
ÏÏ
ÏÏ
ÏÏ
ÏÏ
40
STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
[6]
Replace dipstick firmly.
FUEL
• This engine is certified to operate on gasoline. Exhaust
Emission Control System: EM (Engine Modifications).
TYPE OF FUEL TO USE
• Use clean, fresh, regular unleaded gasoline with a
minimum of 77 octane. Fresh fuel prevents gum from
forming in the fuel system or on essential carburetor parts.
Purchase fuel in quantity that can be used within 30 days.
• Do not use gasoline which contains Methanol.
• Do not mix oil with gasoline.
• For engine protection use Briggs & Stratton Gasoline
Additive available from your Authorized Briggs &
Stratton Dealer (P/N 5041 or single use pouch).
CAUTION: Some fuels, called oxygenated or reformulated gasoline, are gasoline blended with alcohols or
ethers. Excessive amounts of these blends can damage
the fuel system or cause performance problems. If any
undesirable operating symptoms occur, use gasoline
with a lower percentage of alcohol or ether.
ADDING FUEL
WARNING
• Turn engine OFF and let engine cool at least 2
minutes before removing gas cap.
• Fill fuel tank outdoors or in well-ventilated area.
• Keep gasoline away from sparks, open flames,
pilot lights, heat, and other ignition sources.
• If fuel spills, wait until it evaporates before
starting engine.
[1]
Remove cap. Fill tank to approximately 1-1/2
inches below top of neck to allow for fuel
expansion. Be careful not to overfill.
Briggs & Stratton Smart-fill) fuel can fills to the
correct level and automatically shuts off, reducing spills and emissions.
[2]
Replace cap before starting.
STARTING
OIL PRESSURE SWITCH
WARNING
If engine is equipped with an oil pressure switch, the switch
will either activate a warning device or stop the engine
when the engine runs low on oil. (Read the operating
instructions supplied by the equipment manufacturer to
determine which way your engine is equipped because the
equipment manufacturer supplies the oil pressure gauge.)
See oil pressure on page 12 for oil filling instructions.
• Do not use pressurized starting fluids.
• Vapors are flammable.
STARTING AND OPERATING TIPS
♦ Store and fuel equipment in level position.
♦ Use fresh fuel. (See Fuel.)
♦ Use correct type of oil for expected starting
temperature. (See Oil.)
♦ Remove external equipment/engine loads. (See
equipment operating instructions.)
♦ Start lawn mower on hard surface or over previously
cut grass.
♦ Periodically remove grass buildup under mower
deck. (See Maintenance.)
♦ After engine has started, let it warm up several
seconds to several minutes, depending on outside
temperature.
♦ For maximum performance and life, operate engine
with choke in RUN and throttle in FAST.
8
Document: - page 8 (Black)
Screen angle and frequency: 45.0000, 150.0000
STARTING AND STOPPING
REWIND (MANUAL) STARTER
TO START ENGINE
ÏÏ
ÏÏ
Ï
FULL
[1]
[2]
[3]
Check oil level (see p. 7).
WARNING
[5]
Choke
Open fuel shut-off valve
(if equipped).
Move choke control to CHOKE or
START.
Grasp rope handle. Pull slowly
until resistance is felt, then pull
rapidly to start engine and avoid
kickback.
Rewind starter
[4]
Move throttle to FAST
(if equipped). Operate engine with throttle in FAST.
[6]
Let engine warm up.
Choke Equipped: Move
choke
control
lever
toward RUN a short distance at a time over several seconds in warm
weather or minutes in cold
weather. Let engine run
smoothly before each
change. Operate with
choke in RUN.
Rope starter
TO STOP ENGINE
CAUTION:
Do not stop engine
by moving choke
control to CHOKE.
Backfire, fire or engine
damage
could occur.
9
Document: - page 9 (Black)
Screen angle and frequency: 45.0000, 150.0000
[1]
Move throttle
(if
equipped)
to
SLOW, then to STOP.
[2]
Close fuel shut-off
valve
(if equipped).
STARTING AND STOPPING
ELECTRIC (KEY) STARTER (if equipped)
TO START ENGINE
FULL
[1]
[5]
ÏÏ
ÏÏ
Ï
Ï
Check oil level.
Insert key and turn to
START.
[2]
[3]
Choke
Open fuel shut-off valve
(if equipped).
Move choke control to CHOKE or
START.
CAUTION:
To prolong starter life,
use short starting cycles
(5 seconds maximum,
then wait one minute).
Follow
equipment
manufacturer’s recommendations for charging
battery.
[4]
[6]
TO STOP ENGINE
[2]
[3]
[1]
Move throttle
(if equipped) to SLOW.
10
Document: - page 10 (Black)
Screen angle and frequency: 45.0000, 150.0000
Turn key to OFF.
Remove key and
store out of reach of
children.
Close fuel shut-off
valve (if equipped).
Move throttle to FAST (if
equipped). Operate engine with throttle in FAST.
Let engine warm up. Choke
Equipped: Move choke
control lever toward RUN a
short distance at a time over
several seconds in warm
weather or minutes in cold
weather. Let engine run
smoothly
before
each
change. Operate with choke
in RUN.
MAINTENANCE
Perform task at hourly
or calendar interval,
whichever comes first.
Check oil Level
100-300 Hours
Task
100 Hours or
Every Season
Maintenance, replacement or repair of the emission
control devices and systems may be performed by any
nonroad engine repair establishment or individual.
However, to obtain no charge repairs under the terms and
provisions of the Briggs & Stratton warranty statement, any
service or emission control part repair or replacement must
be performed by a factory authorized dealer.
50 Hours or
Every Season
Regular maintenance will improve the performance and
extend the life of the engine. See any Authorized Briggs &
Stratton Dealer for service. Use only genuine Briggs &
Stratton parts. Other parts may not perform as well,
may damage the engine, and may result in injury. In
addition, use of other parts may void your warranty.
25 Hours or
Every Season
EMISSION CONTROL
Every 8 Hours
or Daily
MAINTENANCE
CHANGING OIL
PIPE
4
4*
Change oil
Change oil filter
(if equipped)
4
Service air cleaner
pre-cleaner (if equipped)
4**
Service air cleaner cartridge (if not equipped
with pre-cleaner)
4**
OIL DRAIN PLUG
[1]
WARNING
Service air cleaner cartridge (if equipped with
pre-cleaner)
Inspect spark arrester
(if equipped)
4**
4
[3]
Clean or replace
spark plugs
4
Replace in-line fuel filter
(if equipped)
4
Clean cooling system
Clean combustion
chamber
Typical
drain
plug
[4]
Place engine level.
[2]
Disconnect spark plug
wires and keep away
from spark plugs. Disconnect battery (if equipped with electric starter)
at negative terminal.
With engine OFF but still warm remove oil drain
plug and drain oil into appropriate receptacle.
Reinstall drain plug. Remove dipstick.
[5]
Fill to FULL mark on dipstick with new oil.
Do not overfill.
Note: Engine without oil filter holds approximately 1-1/2
quarts (48 ounces; 1.4 liters). Engine equipped with filter
holds approximately 1-3/4 quarts (56 ounces; 1.7 liters).
4**
4
[6]
Change oil after first 5 to 8 hours of use, then every
50 hours or every season. Change oil every 25 hours
when operating the engine under heavy load or in high
temperatures.
** Clean more often under dusty conditions or when
airborne debris is present. Replace air cleaner parts, if
very dirty.
Replace dipstick.
*
FULL
ÏÏ
CAUTION: Used oil is a hazardous waste product.
Dispose of used oil properly. Do not discard with
household waste. Check with your local authorities,
service center, or dealer for safe disposal/recycling
facilities.
11
Document: - page 11 (Black)
Screen angle and frequency: 45.0000, 150.0000
Ï
Ï
MAINTENANCE
AIR CLEANER
CHANGING OIL FILTER (IF EQUIPPED)
All engines have an oval air cleaner cartridge. In addition,
some engines have a pre-cleaner.
Change oil filter after every 100 hours.
Pre-cleaner
To clean pre-cleaner (if equipped), separate it from
cartridge and wash in liquid detergent and water. Squeeze
dry in a clean cloth. Saturate in engine oil. Squeeze in
clean, absorbent cloth to remove all EXCESS oil.
OIL FILTER P/N
SEE PAGE 16
CAUTION: Do not use pressurized air or solvents to
clean cartridge. Pressurized air can damage
cartridge; solvents will dissolve cartridge.
1/2-3/4
TURN
MORE
REMOVING/INSTALLING AIR CLEANER w/o TANK
[1]
Drain engine oil and remove oil filter.
KNOBS
[2]
Before installing new filter, lightly oil filter gasket
with fresh, clean oil.
COVER
[3]
Screw filter on by hand until gasket contacts oil
filter adapter. Tighten 1/2 to 3/4 turn more.
[4]
Add fresh oil. Fill to FULL line on dipstick.
[5]
Start and run engine at idle to check for leaks.
[6]
Stop engine. Re-check oil level. Add oil if required.
WING UNTS
PRE-CLEANER
and
CARTRIDGE
PART NO. 5052
CARBURETOR
PLATE
CARTRIDGE
PART NO. 394019
PRE-CLEANER
PART NO. 272490
OIL PRESSURE
CARBURETOR
SHIELD
Normal warm operating oil pressure for a pressure lube
engine (engine with oil filter) is 10 to 50 psi at normal
operating temperature. If pressure drops below normal
range, stop engine and check oil level with dipstick. If oil
level is between ADD and FULL mark on dipstick, Do not
restart engine. Contact an Authorized Briggs & Stratton
Service Dealer. Do not operate engine until oil pressure is
corrected.
BODY
Dual element air cleaner
If oil level is below ADD mark on dipstick, add oil to bring
level to FULL mark. Restart engine and check oil pressure.
If pressure is normal, continue to operate engine.
Note: Oil pressure gauge, if engine is equipped, is supplied
by manufacturer of equipment.
12
Document: - page 12 (Black)
Screen angle and frequency: 45.0000, 150.0000
[1]
Remove knobs and cover.
[2]
Slide pre-cleaner off cartridge.
[3]
Remove wing nuts, and cartridge plate. Carefully
remove cartridge to prevent debris from entering
carburetor.
[4]
Reinstall cartridge and cartridge plate. Tighten wing
nuts securely.
[5]
Reassemble pre-cleaner on cartridge.
[6]
Replace cover and tighten knobs securely.
MAINTENANCE
ENGINE AND ENGINE PARTS
We recommend that you see an authorized Briggs & Stratton Service Dealer for all maintenance and service of the engine
and engine parts. Use only genuine Briggs & Stratton parts.
If you perform any maintenance on the engine, first disconnect the spark plug wire
from the spark plug, and disconnect the battery at the negative terminal (electric
starter engines only) to prevent unintentional sparking. Unintentional sparking can
result in fire or electric shock. Unintentional start-up can result in entanglement,
traumatic amputation or laceration. Use only correct tools.
WARNING
• Do not strike the flywheel with a hammer or hard object because the flywheel may
later shatter during operation.
• Do not tamper with governor spring, links or other parts to increase engine speed.
WARNING
MUFFLER
Replacement parts for the
muffler must be the same and
installed in the same position
as the original parts, otherwise fire can occur.
If muffler is equipped with spark
arrestor
screen,
remove
screen for inspection. Replace screen if damaged or plugged.
SPARK PLUG
WARNING
Use only Briggs & Stratton Spark Tester (part number
19368) to check for spark.
.030” (0.76 mm)
Note: In some areas, local
WIRE GAGE
law requires using resistor
spark plug to suppress ignition signals. If this engine
was originally equipped with
resistor spark plug, use
same type for replacement.
RESISTOR P/N 802592
FUEL SYSTEM
WARNING
Replacement parts for fuel
system (cap, hoses, tanks,
filters, etc.) must be the same
as original parts, otherwise
fire can occur.
AIR COOLING SYSTEM
Debris may clog
the engine’s air
cooling system.
Remove blower
housing
and
clean area shown
to prevent overheating and engine damage.
FUEL FILTER (if equipped)
FILTER
PART NO. 394358
(WITH FUEL PUMP)
WARNING
PART NO. 298090 or 5018
(WITHOUT FUEL PUMP)
[1]
Disconnect spark plug
wires and keep away
from spark plugs.
[2]
Drain fuel tank or close
fuel shut-off valve before
replacing
fuel
filter.
Otherwise, fuel can leak
out, creating a fire/explosion hazard.
CLEAN AREAS OF
ALL DIRT AND DEBRIS
13
Document: - page 13 (Black)
Screen angle and frequency: 45.0000, 150.0000
MAINTENANCE
CLEANING DEBRIS
CAUTION: Do not use water to clean engine parts.
Water could contaminate fuel system. Use a brush
or dry cloth.
Daily or before every use, clean accumulated debris from
engine. Keep linkage, springs and controls clean. Keep
area around and behind muffler free of any combustible
debris.
WARNING
CLEAN
Engine parts should be kept
clean to reduce the risk of
overheating and ignition of accumulated debris. This is especially important if cutting tall grass.
DEBRIS
GUARD
Linkage, Springs and Controls
SPARK
ARRESTER
(IF EQUIPPED)
ROTATING
SCREEN
CLEAN
Muffler and Spark Arrester
Debris Guard or Rotating Screen
ADJUSTMENTS
CONTROL ADJUSTMENTS
TO ADJUST REMOTE CHOKE CONTROL
CHOKE
CLOSED
WARNING
CASING
CLAMP
SCREW
Prevent unintentional starting.
CHOKE
LEVER
Before performing adjustments:
• Remove spark plug wire from spark plug.
• Disconnect battery at negative terminal (only
engines with electric start).
14
Document: - page 14 (Black)
Screen angle and frequency: 45.0000, 150.0000
[1]
Remove air cleaner.
[2]
Move choke control to CHOKE or START position.
(Carburetor choke should be completely closed.)
[3]
If not, loosen casing clamp screw.
[4]
Then move casing, wire and engine choke lever
until choke is completely closed.
[5]
Tighten casing clamp screw. Replace air cleaner.
ADJUSTMENTS
TO ADJUST REMOTE THROTTLE CONTROL
TO ADJUST CARBURETOR
IDLE
SPEED
SCREW
If the engine does not start or if it runs roughly, the remote
throttle control may need adjustment. See your authorized
Briggs & Stratton dealer or follow the instructions below.
CARBURETOR
THROTTLE
LEVER
NON-ADJUSTABLE
IDLE MIXTURE JET
Tighten casing clamp screw. Replace air cleaner.
CARBURETOR ADJUSTMENT
WARNING
The manufacturer of the equipment on which this
engine is installed specifies top speed at which the
engine will be operated. DO NOT EXCEED this speed.
Differences in fuel, temperature, altitude or load may
require minor carburetor adjustment. Air cleaner and air
cleaner cover must be assembled to carburetor before
starting engine.
The carburetor on this engine is low emission. It is
equipped with an idle speed adjustment screw and a
non-adjustable idle mixture valve.
Note: Engines operated at approximately 3000 to 5000 feet
(900 to 1500 meters) above sea level may require a high altitude carburetor main jet. If erratic performance is observed,
contact a Briggs & Stratton Authorized Service Dealer for cost
to install/purchase a high altitude carburetor main jet.
15
Document: - page 15 (Black)
Screen angle and frequency: 45.0000, 150.0000
Add sales tax if you live in any of the following states:
**AL 5%, CT 6%, FL 6.5%, GA 4%, KY 6%, MI 6%, MN 6%,
MO 4.225%, NY 8.5%, OH 5%, TN 6%, TX 6.25%, WA 6.5%, WI 5%
[4]
$2.00
$1.50
If not, loosen casing clamp screw. Move casing
and wire in direction shown by arrow until swivel is
against side of quarter circle.
Parts List
Shipping & Handling
**Add State Sales Tax
Total
[3]
EXPIRATION DATE
Move throttle control to FAST. (Swivel should be
against side of quarter circle.)
SIGNATURE (REQUIRED FOR CREDIT CARD ORDERS)
[2]
CREDIT CARD NUMBER
Remove air cleaner.
j VISA
[1]
j Please charge my j MasterCard
CASING
CLAMP
SCREW
(U.S. Dollars, please)
To purchase a complete list of Genuine Briggs & Stratton Parts for your engine, fill in
both sides of this order form carefully. We cannot fill your order without the correct
Engine Model/Type/Code. Allow 3 to 4 weeks for delivery.
QUARTER CIRCLE
j Check or money order enclosed payable to
Briggs & Stratton Corporationin the amount of $_______
SWIVEL
Payment Method:
CASING
CLAMP
SCREW
Start engine and warm up approximately 5 minutes
before adjusting.
[2] With engine running, place throttle control in SLOW
position.
[3] Rotate carburetor throttle lever against the idle
speed screw and hold it.
[4] Turn idle speed screw to obtain 1500 to 1600 rpm.
Note: Governed idle has been set to 1750 rpm at factory.
Fill in both sides of this order form carefully
[1]
SERVICE & STORAGE
PARTIAL LIST OF GENUINE BRIGGS & STRATTON PARTS
BRIGGS & STRATTON
PART NO. (or equivalent)
PART
SERVICE
See an Authorized Briggs & Stratton Service Dealer. Each
one carries a stock of Genuine Briggs & Stratton Parts and
is equipped with special service tools. Trained mechanics
assure expert repair service on all Briggs & Stratton
engines. Only dealers advertising as “Authorized Briggs &
Stratton” are required to meet Briggs & Stratton standards.
When you purchase equipment powered by a
Briggs & Stratton engine, you are assured of
highly skilled, reliable service at more than
30,000
Authorized
Service
Dealers
worldwide, including more than 5,000 Master
Service Technicians. Look for these signs
wherever Briggs & Stratton service is offered.
You may locate your nearest Authorized Briggs & Stratton
Service Dealer in our dealer locator map on our web site
or in the “Yellow Pages”
directory under “Engines, Gasoline” or “Gasoline
 Engines,” or “Lawn Mowers” or similar category.
An illustrated shop manual includes common specifications and detailed information covering adjustment, tune-up and
repair of Briggs & Stratton L-head, twin
cylinder, 4 cycle engines. It is available for
purchase from an Authorized Briggs &
Stratton Service Dealer or you can order it
from the factory. Write: Briggs & Stratton
Corporation, Attn: Service Division
Part No. 271172
P. O. Box 1144, Milwaukee, WI 53201
To purchase a complete list of Genuine Briggs & Stratton Parts for your engine, fill in
both sides of this order form carefully. We cannot fill your order without the correct
Engine Model/Type/Code. Allow 3 to 4 weeks for delivery.
Code
Type
Your Engine
Model
City
Address
Name
Fill in both sides, clip and return to:
Briggs & Stratton Corporation
P.O. Box 1144
Milwaukee, WI 53201–1144 U.S.A.
State
Zip
Country
Air cleaner cartridge
394019
Air cleaner pre-cleaner
272490
Air cleaner pre-cleaner and cartridge
5052
Oil
100005 or 100028
Oil filter (3-1/2 in. long)
491056
Oil filter (2-1/4 in. long)
492932 or 5049
Fuel filter (with fuel pump)
394358
Fuel filter (without fuel pump)
298090 or 5018
Gas additive
5041
Resistor spark plug
802592
Long life platinum spark plug
5062
(used on most L-head engines)
Spark plug wrench
89838 or 5023
Spark tester
19368
Oil pump kit
5056
(uses standard electric drill to remove oil from engine quickly)
STORAGE
Engines stored over 30 days need special attention.
[1] To prevent gum from forming in fuel system or on
essential carburetor parts:
a) if fuel tank contains oxygenated or reformulated
gasoline (gasoline blended with an alcohol or an
ether), run engine until it stops from lack of fuel, or b) if
fuel tank contains gasoline, either run engine until it
stops from lack of fuel, or add a gasoline additive to the
gas in the tank. (See parts list. Single – use pouches of
gas additive are available from your service dealer.) If
you use a gas additive, run the engine for several
minutes to circulate the additive through the carburetor.
Then, engine and fuel can be stored up to 24 months.
[2] While engine is still warm, change oil.
[3] Remove spark plugs and pour about 1 oz. (30 ml) of
engine oil into each cylinder. Replace spark plugs and
crank slowly to distribute oil.
[4] Clean engine of surface debris, chaff or grass.
[5]
16
Document: - page 16 (Black)
Screen angle and frequency: 45.0000, 150.0000
WARNING
Store in a clean, dry area. Do
not store in same area as a
stove, furnace, water heater, or
other appliance that uses a pilot
light or has a device that can
create a spark.
LIMITED WARRANTY
Briggs & Stratton Corporation will repair or replace, free of charge, any part(s) of the engine that is defective in material or workmanship or both.
Transportation charges on parts submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for the
time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map
at www.briggsandstratton.com, or by calling 1-800-233-3723, or as listed in the ‘Yellow Pages’.
THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIED
WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT
EXCLUSION IS PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or
countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state and country to country.
( )(
"
r
(Sleeve Bore)
!"
(Kool Bore)
!# $
%&r
%!
%45
'
2 years
2 years
1 year
1 year
90 days
90 days
)*
Consumer Use
Commercial Use
*
2 years
1 year
Note the following special warranty periods: 2 years for Classic engines in the European Union and Eastern European countries, for all consumer products in
the European Union, and for emission control systems on engines certified by EPA and CARB. 5 years for consumer use, 90 days for commercial use of Touch-NMow starter on Quantum and Intek engines. Engines used in competitive racing or on commercial or rental tracks are not warrantied.
The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the table
above. “Consumer use” means personal residential household use by a retail consumer. “Commercial use” means all other uses, including use for commercial,
income producing or rental purposes. Once an engine has experienced commercial use, it shall thereafter be considered as a commercial use engine for purposes of this warranty.
NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF PURCHASE
RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED, THE
MANUFACTURING DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.
( ( !
" #
$ # !
$ !
% &
' # ( " & #
! "
# $
! ! %
!! ! "
&
! '
% ) *+,-' ./' 0 *+& &1& +' 2,&
,+$3$2- +$33 &+&&,2 *+&
4 ' 5.
6
7 -# # 5/ 8 ! * 2
9:;)6
; * # 5# <=
+ 6 ,$- 3+ ' + , $
9 + % > 8 8
5 17
Engwnty1-03 - page 1 (Black)
Screen angle and frequency: 45.0000, 150.0000
8
,8!
 8 6 +
, $
? * 8 5. 6 + , $
< ' # "
# 8 @ # # # % " 8 ): +
8 % )) ' !"! !!
! !( )"" * +
,
&
-!( + . !
/0 1"2 !
/
"
3
2 /3
"
2 /4
52 "&
! !'!! +,- . /! !" ! +,
. ( 0!& !"! "1 +(22 ,
&! !! 1& 1 & +#3 )/" 1 . 4!,
EMISSION CONTROL WARRANTY COVERAGE IS APPLICABLE TO CERTIFIED ENGINES PURCHASED IN CALIFORNIA IN 1995 AND THEREAFTER, WHICH ARE USED IN CALIFORNIA, AND TO CERTIFIED MODEL YEAR 1997 AND LATER ENGINES WHICH ARE PURCHASED AND
USED ELSEWHERE IN THE UNITED STATES (AND AFTER JANUARY 1, 2001 IN CANADA).
/! ( &! !! )/" 1 &
The California Air Resources Board (CARB), U.S.
EPA and B&S are pleased to explain the Emission
Control System Warranty on your model year
2002 and later small off-road engine (SORE). In
California, new small off-road engines must be designed, built and equipped to meet the State’s
stringent anti-smog standards.
Elsewhere in the United States, new non-road,
spark-ignition engines certified for model year
1997 and later must meet similar standards set
forth by the U.S. EPA. B&S must warrant the emission control system on your engine for the periods
of time listed below, provided there has been no
abuse, neglect or improper maintenance of your
small off-road engine.
Your emission control system includes parts
such as the carburetor, air cleaner, ignition system, muffler and catalytic converter. Also included may be connectors and other emission
related assemblies.
Where a warrantable condition exists, B&S will
repair your small off-road engine at no cost to
you including diagnosis, parts and labor.
! &! !! )/" 1 !0
Small off-road engines are warranted relative to emission control parts defects for a period of two years, subject to provisions set forth below. If any
covered part on your engine is defective, the part will be repaired or replaced by B&S.
#3 1 '!4
As the small off-road engine owner, you are responsible for the performance of the required
maintenance listed in your Operating and Maintenance Instructions. B&S recommends that
you retain all your receipts covering maintenance on your small off-road engine, but B&S
cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.
As the small off-road engine owner, you should
however be aware that B&S may deny you warranty coverage if your small off-road engine or a
part has failed due to abuse, neglect, improper
maintenance or unapproved modifications.
You are responsible for presenting your small
off-road engine to an Authorized B&S Service
Dealer as soon as a problem exists.
The undisputed warranty repairs should be
completed in a reasonable amount of time, not
to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should contact a B&S Service Representative at
1-414-259-5262.
The emission warranty is a defects warranty.
Defects are judged on normal engine performance. The warranty is not related to an in-use
emission test.
! &! !! )/" 1 !0!
The following are specific provisions relative to your Emission Control Defects Warranty Coverage. It is in addition to the B&S engine warranty for nonregulated engines found in the Operating and Maintenance Instructions.
1. Warranted Parts
2. Length of Coverage
set forth in the B&S Engine Warranty Policy.
B&S is not liable to cover failures of WarB&S warrants to the initial owner and each
Coverage under this warranty extends only
ranted Parts caused by the use of add-on,
subsequent purchaser that the Warranted
to the parts listed below (the emission connon-original, or modified parts.
Parts shall be free from defects in materials
trol systems parts) to the extent these parts
and workmanship which caused the failure 5. Maintenance
were present on the engine purchased.
of the Warranted Parts for a period of two
Any Warranted Part which is not scheduled
a. Fuel Metering System
years from the date the engine is delivered to
for replacement as required maintenance or
•
Cold start enrichment system
a retail purchaser.
which is scheduled only for regular inspec•
Carburetor and internal parts
3. No Charge
tion to the effect of “repair or replace as nec•
Fuel Pump
essary” shall be warranted as to defects for
Repair or replacement of any Warranted
b. Air Induction System
the warranty period. Any Warranted Part
Part will be performed at no charge to the
which is scheduled for replacement as re•
Air cleaner
owner, including diagnostic labor which
quired maintenance shall be warranted as to
leads to the determination that a Warranted
•
Intake manifold
defects only for the period of time up to the
Part
is
defective,
if
the
diagnostic
work
is
c. Ignition System
first scheduled replacement for that part. Any
performed at an Authorized B&S Service
•
Spark plug(s)
replacement part that is equivalent in perforDealer. For emissions warranty service
•
Magneto ignition system
mance and durability may be used in the percontact your nearest Authorized B&S Serformance of any maintenance or repairs.
vice Dealer as listed in the “Yellow Pages”
d. Catalyst System
The owner is responsible for the perforunder “Engines, Gasoline,” “Gasoline En•
Catalytic converter
mance of all required maintenance, as degines,”
“Lawn
Mowers,”
or
similar
category.
•
Exhaust manifold
fined in the B&S Operating and Maintenance
4. Claims and Coverage Exclusions
•
Air injection system, Pulse valve
Instructions.
Warranty claims shall be filed in accordance
e. Miscellaneous Items
with the provisions of the B&S Engine War- 6. Consequential Coverage
•
Vacuum, temperature, position,
ranty Policy. Warranty coverage shall be exCoverage hereunder shall extend to the failtime sensitive valves
cluded for failures of Warranted Parts which
ure of any engine components caused by
and switches
are not original B&S parts or because of
the failure of any Warranted Part still under
•
Connectors and assemblies
abuse, neglect or improper maintenance as
warranty.
' / , , , & !
*A 84;?)?? 5, * *6
5,819,513
5,606,948
5,497,679
5,235,943
6,325,036
6,077,063
5,813,384
5,606,851
5,320,795
5,197,425
6,284,123
6,064,027
5,548,955
5,271,363
5,197,422
5,765,713
6,260,529
6,014,808
5,645,025
5,546,901
5,269,713
5,191,864
6,230,678
5,894,715
6,202,616
5,852,951
5,642,701
5,503,125
5,265,700
5,188,069
6,116,212
5,823,153
5,619,845
5,501,203
5,243,878
5,186,142
18
Engwnty1-03 - page 2 (Black)
Screen angle and frequency: 45.0000, 150.0000
5,138,996
5,086,890
5,070,829
5,058,544
5,040,644
5,009,208
4,996,956
4,977,879
4,971,219
4,895,119
4,819,593
4,719,682
4,633,556
4,630,498
4,522,080
4,520,288
4,512,499
4,453,507
4,430,984
DES. 308,871
DES. 308,872
DES. 309,457
DES. 356,951
DES. 361,771
DES. 375,963
! "# $%& ! %% ' %
! "
#$%%! %%& !'
(# $# (' )**+ # , - ' .
# ('/ -
0 !'" (# " )**1 # .
, - ' ## $# # 0 %# )
2, 344) "5
6 7 & &/ & 897 7 :8
55 % &; <= = >?8 97<8 8 < : 8? 3444 9 9 '5 6/ := 8 < : @ 7A/ 7 99 7 = 5 = / := 8 < B
C 8 769 8? )**1 / : 7 8 8.
8 : 55 %5 & ; >?8 7D 97<.
8 : 8 9 8 89 77/ 6 6 CE
C/ 97 95
, >?8 7D 97<8 78 ?7 7C/ 6 B
/ >?8 / 7= 7: 7>5 78 77 ?7 9 B 985
> 7 B / &; 9 8 : 8 < 7
7/ ?7 8 F:5
8 < 7 9679 ?7 >?8 7D.
97<8 9 3 / E = 7 9 775 8.
?7 : 8 7: 7 967/ 99 879 &;5
9 8 < / : @ C : B =97
9 : 8 9 5 &; : 78.
8 7: A 7: := : 8 < .
/ 8 &; 6 C7 A 96 : :
97<97 88 5
9 8 < / : :G @ 689 &; 6
< 7 9679 : 8 : 8 B
8 C6/ 97/ 77 867 :95
, :G C9 : 8 < B 9 9 &;
D : C?85 9 : @ 7899 9 C : =79 H4 E5
: :G :8 B : / : C9/ :G
788 :7 9 :7 &; 89 )I)I3+*+3J35
>?8 97<8 7 96795 967.
9 E9 67 8 85 9 B 97<8 6679 B 95
(% "# $%& %% "# ) $%&
'% %
( "# $%& 77 976 :8 B : >?8 7D 97<85 B &; 8 989 7
8 5
)5 # H5 7 (
7: 7 ?7 9 77 9 878 ?7 6679 7
>?8 7D 97<8 8 K 7 ?7 9 9 6 9/ 7 6 8 F: 7 6 98.
8 88 7<5
?7 967/ 7 B 7 7 6679
7<G
9 9 &;5 % : >?8 97<8/ 788.
5 >?8 7C
G
:7 9 9 &; 7< 9 E • >?8 7<8 98 B 6
: 79 C 8 B 7/ 79 85
• C I5 978 =7 7:5
• %8 B 7
978 : @ 7899 77 :7 C5 >?8 7 &;5 7: 9679 ?7 • ( B ?7 &; 7 C/ 97 95
• C 8
&; 7: 9679 ?7 6 CE
75 >?8 E/ 99 869 ?7 ?7 &; 5
• & 8
+5 • >?8 8 9789
?7 879 88 8 .
5 >?8 7>
69 8 7 9? 8 LM9 • : 7>
87 97MN 7 9679 9 5
• 7 97<8
?7 69 878 .
• >?8 E7 B 7 9679 8 9 8 : E
5 ?7 9 >?8 7< 89
8 878 9: 7 ?75 ?7 878 9: • 9/ 89/ 5
687 C9 @ 9 95 9 C =97 96 8 7
• 7 8C5
&; 95
35 (% J5 : 7
&; 9 7< C9 ?7 .
7: 77 9 B 9679 78 8 79 =8 :7 8? 6C7 7 967.
9679 8 ?7 7: 7
9 ?7 9 = B B 8.
99 :9 B 7<5
:5
* % '% $% $+,(+ $ $%- $% 8 769 768 = 8 98 6 7 & & 3/ : 667< 68 77 9 C9 >?8
98 " 5 68 9 9 9 8 & ; 5 9 8 8 77 7675
% '% $% 8C < 8 8 769 768 = 8 98 9: 9 9 8 9 5 79 : 9MO
.%%
8 769 768 )3+ < 85
+%
8 769 768 3+4 < 85
%
8 769 768 +44 < 85
% =8/ 8? 9 : 34 B 3+ < 95 % 79/ % '% $% 8 79 89 7 > 9: B )4 B )3 5
$ 8C 97 : 6 98 79 976 85 % $ C/ 8 975 68 9 68 < 9 985
/ 0 1 2333 * % % $% %-
? ) E 3444/ 7 8 &; 769 768 = 8 :8 98 :8 %7 7> % %< 35 % 8 769 %< 3/ 9 7689 98 89 9 8C < 8 7 8 6995 % 8 67 8 33+ 77/ 79 P )3+ </ & P 3+4 < P +44 <5 % 8 33+ 77 / 79 P 3+4 </ & P +44 < P )444 <5
878 8 8? 9 I34444 J*I 775 878 8 8? 9 IJ4444 1I+ 775
% %- $%
- * %4O
Document: - page 1 (Black)
Screen angle and frequency: 45.0000, 150.0000
INFORMATIONS IMPORTANTES
CORPORATION BRIGGS & STRATTON
FAMILLE YBSXS.3192VA
274812
CE MOTEUR EST CONFORME AUX NORMES
ANTIPOLLUTION 2000 – 2001 DE CALIFORNIE
POUR LES PETITS MOTEURS HORS ROUTE ET
AUX NORMES ENVIRONNEMENTALES
AMÉRICAINES (EPA PHASE 2) POUR LES
PETITS MOTEURS HORS ROUTE. CONSULTEZ
LE MANUEL DU PROPRIÉTAIRE POUR LES
SPÉCIFICATIONS, L’ENTRETIEN ET LES
AJUSTEMENTS. CONFORME À LA PÉRIODE
D’ÉMISSION EPA : CATÉGORIE : C
Download PDF