YOODA 15LEU/L 0,3 Nm, 30RPM tubular motor Instruction

NAPĘDY SERII 15LEU/L
www.sukcesgroup.pl
Non-compliance with the specification might cause risk for life or health and can determine proper work of the blinds.
We strongly recommend to comply with the specification.
1. General information
LEU/L type motors wit two way equipped with a radio receiver
are wireless and can be controlled with a remote. They are
designed for automation of blinds. They have electronic limit
switches which are programmed by the remote control. Built-in
battery makes it easy to mount the motor without having
power supply. LEU/L series tubular motors are compatible
with all YOODA brand devices.
Radio receiver memory:
up to 20 transmitters
Power supply:
USB DC 5 V 2 A
Operating temperature:
from -10°C to 55°C
Protection degree:
IP 40
15 LEU/L tubular motor with radio receiver and battery
Load:
2,5 kg
antenna
battery
charging socket
radio receiver,
limit switches system
motor
gear
LED diode
head visible from
the other side
programming button
PROGRAMMING BUTTON FUNCTIONS:
1. Pressing the programming button briefly for approximately 1 second controls the drive step by step.
2. Pressing the programming button for 2 secons enters the motor into the transmitter programming mode.
3. Pressing the programming button for 6 seconds activates the function of blocking the radio signal. To deactivate the
function, briefly press the programming button on the motor head or disconnect motor power.
4. Pressing the programming button for 10 seconds changes work motor direction.
5. Pressing the programming button for 14 seconds deletes the motor memory and restores the factory settings.
1
2. Safety measures
Before installing or using motor please read the following instruction. The installer must comply with the standards and regulations in
force in the country where the appliance will be installed and provide information to users about the conditions and maintenance of the
device. Failure to follow these instructions can present risk to life and health, or invalid functioning of the roller shutter. This also results
in the loss of warranty rights.
Motors torque parameter should be adequate to the
weight of the roller shutter curtain.
Electrical system control should be performed
regularly to detect any signs of use or damage
of the motor.
Do not hit the motor. Reduce the vibration of the
motor to a minimum.
All contact of the motor with any liquids should be
reduced to minimum.
No tools should be used when placing motor
in the tube.
Motor and its control system should be kept out
or reach of children.
During the adapter montage special attention must
be paid not to damage the motor.
3. Placing motor in the tube
Motor should be mounted in places protected from unfavourable weather conditions. Do not pull the motor head when
removing it from the tube.
1. Cut the tube
to the proper length.
2. Deburr the edges
and remove the metal residue.
3. Place the adaptation
on the motor.
4. Measure the distance (L)
between the inner edge of motors head
and the end of the motors adaptor.
5. Insert the motor into the tube
up to the point of connection
between the edge of the tube and
the inner edge of the motors head.
6. Attach the tube to the
coupling part of the adaptation.
2
4. Charging
1. Ensure that the drive is fully charged before initial startup.
2. Charge the battery at least once every 6 months for a minimum of 3 hours.
3. The motor has a built-in 8 V battery, which should be charged with a 5 V charger with a maximum of 2 A.
When the battery voltage is below
7.2V, the red LED diode flashes
during work motor.
When the battery is charging,
the green LED diode flashes.
When the green LED diode lights up,
the battery is charged.
5. Range
Radio receiver range is a variable value and can differ from declared values depending on conditions in which device operates.
Possible sources of changes in range are building construction, interference caused by other radio transmitters etc.
Blinds with remotely controlled motor
20
L1
L2
230 V / 50 Hz
L1
Outdoor
200 m
L2
Indoor
35 m
Operating
frequency
433,92 MHz
6. Programming first transmitter
1. Longer than 10 seconds pause between series of button clicks during programming will cause device to switch off from
programming mode without saving any changes.
2. Programming the first transmitter removes the previously programmed transmitters from memory.
Press and hold for about
2 seconds programming
button on the motor head.
Blind will make
short up/down
movements.
Press
programming button
P2 on the remote control.
Blind will make
short up/down
movements.
Press
programming button
P2 on the remote
Blind will make
short up/down
movements.
Press
UP button.
Blind will make
short up/down
movements. Transmitter
has been programmed.
7. Changing motors direction
Motor’s direction
has been changed.
When pressing
DOWN button blind
moves up.
Press and hold
for about 10 seconds
programming button
on the motor head.
Blind will make
3 short up/down
movements.
3
When pressing DOWN
button, blind
moves down.
8. Programming limit positions
To set the upper and lower limit position press the programming button P2 during the motor movement, it causes the work
displacement. Then you can precisely set the limit positions. Pressing the P2 button again motor will run continuously.
Press
programming
button P2.
Blind
will make short up/down
movements.
Blind will make
short up/down
movements.
Press
UP button.
Press
programming
button P2 again.
Blind will make
short up/down
movements.
Upper
limit position
Press
UP button.
Limit positions
has been
programmed.
When the blind reaches
upper limit position press
STOP button.
Press STOP button
5 times at 0.5 sec
intervals to confirm
the upper
limit position.
Blind will make
short up/down
movements.
Press
DOWN button.
Lower
limit position.
Press STOP button
When
5 times at 0.5 sec intervals
the blind
to confirm the lower limit
reaches lower
position.
limit position
press STOP button
Blind will make
short up/down
movements.
9. Regulation limit positions
In the case of setting the limit positions, it is possible to correct the upper or lower limit position.
Limit position
has been corrected.
Set the motor in the upper
or lower limit position.
Simultaneously press
and hold UP and DOWN
buttons for 5 seconds.
Blind will make
short up/down
movements.
Press the UP or DOWN
buttons to set a new limit position.
Press STOP button
5 times at 0.5 sec intervals
to confirm the new limit
position.
Blind will make
short up/down
movements.
10. Removing limit positions
Limit positions
has been removed.
Press
programming
button P2.
Blind will make
short up/down
movements.
Press
DOWN button.
Blind will make
short up/down
movements.
Press
programming
button P2.
Blind will make
short up/down
movements.
11. Programming the third limit position
1. After setting the upper and lower limit positions, it is possible to set the third position (favorite) between those positions.
2. Hold the STOP button for 3 seconds to set the blind in third limit position.
3. When the drive is in impulse mode, holding down the STOP button for 3 seconds will cause it to move to the lower limit
position and then to the set third position.
4
Upper limit position
has been set.
An example of the third
limit position
Lower limit position
has been set.
Programming
the third limit position.
Blind will make
short up/down
movements.
Press
programming
button P2.
The third limit position
has been set.
Blind will make
short up/down
movements.
Press
STOP button.
Blind will make
short up/down
movements.
Press
STOP button.
12. Removing third limit position
The third limit position
has been removed.
Press
programming
button P2.
Blind will make
short up/down
movements.
Press
STOP button.
Blind will make
short up/down
movements.
Press
STOP button.
Blind will make
short up/down
movements.
13. Programming another transmitter
1. Receiver can be controlled by up to 20 transmitters.
2. Longer than 6 seconds pause between series of button clicks during programming will cause device to switch off from
programming mode without saving any changes.
METHOD 1:
Press p
rogramming button P2
on the A remote control.
Blind will make
short up/down
movements.
Press
programming button P2
on the A remote control.
Blind will make
short up/down
movements.
Press
programming button P2
on the B remote control.
Blind
will make short
up/down
movements.
Remote control
has been programmed.
METHOD 2:
Remote control
has been programmed.
Press and hold
for about 2 seconds
programming button
on the motor head.
Blind will make
short up/down
movements.
Simultaneously press
UP and DOWN
buttons.
5
Blind will make
short up/down
movements.
14. Deleting another transmitter
Press
programming button P2
on the A remote control.
Blind will make
short up/down
movements.
Press
programming button P2
on the A remote control.
Blind will make
short up/down
movements.
Press
programming button P2
on the B remote control.
Blind will make
short up/down
movements.
Remote control
has been removed.
15. Deleting motor memory
1. Deleting memory of motors radio receiver will cause for all programmed transmitters to be lost.
2. Longer than 5 seconds pause between series of button clicks during programming will cause device to switch off from
programming mode without saving any changes.
Press
programming button P2
on the remote control.
Blind will make
short up/down
movements.
Press
STOP button.
Press
programming button P2
on the remote control.
Blind will make
short up/down
movements.
Blind will make
short up/down
movements.
All active transmitters have
been removed from memory.
16. Activating impulse mode
1.Longer than 10 seconds pause between series of button clicks during programming will cause device to switch off from
programming mode without saving any changes.
2. To activate impulse mode follow the procedure below. To deactivate impulse mode repeat this procedure.
Impulse mode
has been activated.
Press
programming button P2
on the remote control.
Blind will make
short up/down
movements.
Press
UP button.
Press
DOWN button.
Blind will make
short up/down
movements.
Blind will make
short up/down
movements.
When you press the direction
button once on the remote
control, the motor will
make a short move.
17. Motor speed regulation
If the motor does not respond when pressed, it means that it is set to the smallest or highest speed motor.
INCREASE SPEED OF THE MOTOR:
2x
3x
MOTOR SPEED REDUCTION:
If the motor performs
2 up / down movements,
the intermediate
speed is set.
If the motor performs
3 up / down movements,
the highest speed is set.
Simultaneously
press and hold
STOP and UP buttons
for 2 seconds.
Simultaneously
press and hold
DOWN and STOP
buttons for 2 seconds.
6
1x
If the motor performs one
up / down movement, the
lowest speed is set.
2x
If the motor performs 2 up /
down movements, the
intermediate speed is set.
18. Programming key-ring remotes
1. When programming key-ring remotes that do not have additional P2 programming button the same function is
substituted with simultaneous push of STOP and UP buttons.
2. Longer than 5 seconds pause between series of button clicks during programming will cause device to switch
off from programming mode without saving any changes.
Press and hold
for about 2 seconds
programming button
on the motor head.
Blind will make
short up/down
movements.
Press simultaneously
STOP
and UP
programming buttons.
Blind will make
short up/down
movements.
7
Press simultaneously
STOP
and UP
programming buttons.
Blind will make
short up/down
movements.
Press
UP button.
Blind will make short
up/down movements.
Key-ring remote has
been programming.
">