Automation Direct CDS-USER-M Owner's Manual

Manual Number: P2CDS-USER-M
~ WARNING ~
Thank you for purchasing automation equipment from Automationdirect.com®, doing business as,
AutomationDirect. We want your new automation equipment to operate safely. Anyone who installs or
uses this equipment should read this publication (and any other relevant publications) before installing
or operating the equipment.
To minimize the risk of potential safety problems, you should follow all applicable local and national
codes that regulate the installation and operation of your equipment. These codes vary from area
to area and usually change with time. It is your responsibility to determine which codes should be
followed, and to verify that the equipment, installation, and operation is in compliance with the latest
revision of these codes.
At a minimum, you should follow all applicable sections of the National Fire Code, National Electrical
Code, and the codes of the National Electrical Manufacturer’s Association (NEMA). There may be local
regulatory or government offices that can also help determine which codes and standards are necessary
for safe installation and operation.
Equipment damage or serious injury to personnel can result from the failure to follow all applicable
codes and standards. We do not guarantee the products described in this publication are suitable for
your particular application, nor do we assume any responsibility for your product design, installation, or
operation.
Our products are not fault-tolerant and are not designed, manufactured or intended for use or resale
as on-line control equipment in hazardous environments requiring fail-safe performance, such as in the
operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, direct life
support machines, or weapons systems, in which the failure of the product could lead directly to death,
personal injury, or severe physical or environmental damage (“High Risk Activities”). AutomationDirect
specifically disclaims any expressed or implied warranty of fitness for High Risk Activities.
For additional warranty and safety information, see the Terms and Conditions section of our catalog.
If you have any questions concerning the installation or operation of this equipment, or if you need
additional information, please call us at 770-844-4200.
This publication is based on information that was available at the time it was printed. At
AutomationDirect we constantly strive to improve our products and services, so we reserve the right
to make changes to the products and/or publications at any time without notice and without any
obligation. This publication may also discuss features that may not be available in certain revisions of
the product.
Trademarks
This publication may contain references to products produced and/or offered by other companies. The product and company names
may be trademarked and are the sole property of their respective owners. AutomationDirect disclaims any proprietary interest in the
marks and names of others.
Copyright© 2024, Automationdirect.com® Incorporated
All Rights Reserved
No part of this manual shall be copied, reproduced, or transmitted in any way without the prior, written consent of Automationdirect.
com® Incorporated. AutomationDirect retains the exclusive rights to all information included in this document.
~ ADVERTENCIA ~
Gracias por comprar equipo de automatización de Automationdirect.com®. Deseamos que su nuevo
equipo de automatización opere de manera segura. Cualquier persona que instale o use este equipo
debe leer esta publicación (y cualquier otra publicación pertinente) antes de instalar u operar el
equipo.
Para reducir al mínimo el riesgo debido a problemas de seguridad, debe seguir todos los códigos
de seguridad locales o nacionales aplicables que regulan la instalación y operación de su equipo.
Estos códigos varian de área en área y usualmente cambian con el tiempo. Es su responsabilidad
determinar cuales códigos deben ser seguidos y verificar que el equipo, instalación y operación estén
en cumplimiento con la revisión mas reciente de estos códigos.
Como mínimo, debe seguir las secciones aplicables del Código Nacional de Incendio, Código Nacional
Eléctrico, y los códigos de (NEMA) la Asociación Nacional de Fabricantes Eléctricos de USA. Puede
haber oficinas de normas locales o del gobierno que pueden ayudar a determinar cuales códigos y
normas son necesarios para una instalación y operación segura.
Si no se siguen todos los códigos y normas aplicables, puede resultar en daños al equipo o lesiones
serias a personas. No garantizamos los productos descritos en esta publicación para ser adecuados
para su aplicación en particular, ni asumimos ninguna responsabilidad por el diseño de su producto,
la instalación u operación.
Nuestros productos no son tolerantes a fallas y no han sido diseñados, fabricados o intencionados
para uso o reventa como equipo de control en línea en ambientes peligrosos que requieren una
ejecución sin fallas, tales como operación en instalaciones nucleares, sistemas de navegación aérea, o
de comunicación, control de tráfico aéreo, máquinas de soporte de vida o sistemas de armamentos
en las cuales la falla del producto puede resultar directamente en muerte, heridas personales, o daños
físicos o ambientales severos (“Actividades de Alto Riesgo”). Automationdirect.com específicamente
rechaza cualquier garantía ya sea expresada o implicada para actividades de alto riesgo.
Para información adicional acerca de garantía e información de seguridad, vea la sección de Términos
y Condiciones de nuestro catálogo. Si tiene alguna pregunta sobre instalación u operación de este
equipo, o si necesita información adicional, por favor llámenos al número 770-844-4200 en Estados
Unidos.
Esta publicación está basada en la información disponible al momento de impresión. En
Automationdirect.com nos esforzamos constantemente para mejorar nuestros productos y servicios,
así que nos reservamos el derecho de hacer cambios al producto y/o a las publicaciones en cualquier
momento sin notificación y sin ninguna obligación. Esta publicación también puede discutir
características que no estén disponibles en ciertas revisiones del producto.
Marcas Registradas
Esta publicación puede contener referencias a productos producidos y/u ofrecidos por otras compañías. Los nombres de las
compañías y productos pueden tener marcas registradas y son propiedad única de sus respectivos dueños. Automationdirect.com,
renuncia cualquier interés propietario en las marcas y nombres de otros.
Propiedad Literaria© 2024, Automationdirect.com® Incorporated
Todos los derechos reservados
No se permite copiar, reproducir, o transmitir de ninguna forma ninguna parte de este manual sin previo consentimiento por escrito
de Automationdirect.com® Incorprated. Automationdirect.com retiene los derechos exclusivos a toda la información incluida en este
documento. Los usuarios de este equipo pueden copiar este documento solamente para instalar, configurar y mantener el equipo
correspondiente. También las instituciones de enseñanza pueden usar este manual para propósitos educativos.
~ AVERTISSEMENT ~
Nous vous remercions d’avoir acheté l’équipement d’automatisation de Automationdirect.com®,
en faisant des affaires comme, AutomationDirect. Nous tenons à ce que votre nouvel équipement
d’automatisation fonctionne en toute sécurité. Toute personne qui installe ou utilise cet équipement
doit lire la présente publication (et toutes les autres publications pertinentes) avant de l’installer ou de
l’utiliser.
Afin de réduire au minimum le risque d’éventuels problèmes de sécurité, vous devez respecter
tous les codes locaux et nationaux applicables régissant l’installation et le fonctionnement de votre
équipement. Ces codes diffèrent d’une région à l’autre et, habituellement, évoluent au fil du temps. Il
vous incombe de déterminer les codes à respecter et de vous assurer que l’équipement, l’installation
et le fonctionnement sont conformes aux exigences de la version la plus récente de ces codes.
Vous devez, à tout le moins, respecter toutes les sections applicables du Code national de prévention
des incendies, du Code national de l’électricité et des codes de la National Electrical Manufacturer’s
Association (NEMA). Des organismes de réglementation ou des services gouvernementaux locaux
peuvent également vous aider à déterminer les codes ainsi que les normes à respecter pour assurer
une installation et un fonctionnement sûrs.
L’omission de respecter la totalité des codes et des normes applicables peut entraîner des dommages
à l’équipement ou causer de graves blessures au personnel. Nous ne garantissons pas que les produits
décrits dans cette publication conviennent à votre application particulière et nous n’assumons aucune
responsabilité à l’égard de la conception, de l’installation ou du fonctionnement de votre produit.
Nos produits ne sont pas insensibles aux défaillances et ne sont ni conçus ni fabriqués pour
l’utilisation ou la revente en tant qu’équipement de commande en ligne dans des environnements
dangereux nécessitant une sécurité absolue, par exemple, l’exploitation d’installations nucléaires,
les systèmes de navigation aérienne ou de communication, le contrôle de la circulation aérienne,
les équipements de survie ou les systèmes d’armes, pour lesquels la défaillance du produit peut
provoquer la mort, des blessures corporelles ou de graves dommages matériels ou environnementaux
(«activités à risque élevé»). La société AutomationDirect nie toute garantie expresse ou implicite
d’aptitude à l’emploi en ce qui a trait aux activités à risque élevé.
Pour des renseignements additionnels touchant la garantie et la sécurité, veuillez consulter la section
Modalités et conditions de notre documentation. Si vous avez des questions au sujet de l’installation
ou du fonctionnement de cet équipement, ou encore si vous avez besoin de renseignements
supplémentaires, n’hésitez pas à nous téléphoner au 770-844-4200.
Cette publication s’appuie sur l’information qui était disponible au moment de l’impression. À la
société AutomationDirect, nous nous efforçons constamment d’améliorer nos produits et services.
C’est pourquoi nous nous réservons le droit d’apporter des modifications aux produits ou aux
publications en tout temps, sans préavis ni quelque obligation que ce soit. La présente publication
peut aussi porter sur des caractéristiques susceptibles de ne pas être offertes dans certaines versions
révisées du produit.
Marques de commerce
La présente publication peut contenir des références à des produits fabriqués ou offerts par d’autres entreprises. Les désignations des
produits et des entreprises peuvent être des marques de commerce et appartiennent exclusivement à leurs propriétaires respectifs.
AutomationDirect nie tout intérêt dans les autres marques et désignations.
Copyright© 2024, Automationdirect.com® Incorporated
Tous droits réservés
Nulle partie de ce manuel ne doit être copiée, reproduite ou transmise de quelque façon que ce soit sans le consentement préalable
écrit de la société Automationdirect.com® Incorporated. AutomationDirect conserve les droits exclusifs à l’égard de tous les
renseignements contenus dans le présent document.
Publication History
ProductivityCodesys User Manual
Please include the Manual Number and the Manual Issue, both shown below,
when communicating with Technical Support regarding this publication.
Manual Number:
P2CDS-USER-M
Issue Date: 1/24/2024
Issue: Issue
Date
1st Edition
1/2024
1st Edition
Publication History
Description of Changes
Original
Table of Contents
In This Manual
Introduction...................................................................................................................................... 1–2
Purpose of this Manual .........................................................................................................................1–2
Intended Use of This Product ..............................................................................................................1–2
Benefits of P2CDS-622 with CODESYS Software..................................................................... 1–3
Conventions Used............................................................................................................................ 1–4
Key Topics for Each Chapter...................................................................................................................1–4
Important Online Resources......................................................................................................... 1–5
P2CDS-622 System.......................................................................................................................... 1–6
Preparation....................................................................................................................................................1–6
1. CODESYS IDE Install............................................................................................................................1–6
2. P2CDS-622 Firmware Install.............................................................................................................1–6
3. System Requirements and Installation........................................................................................1–6
4. Installation...............................................................................................................................................1–7
5. PLC On the Network...........................................................................................................................1–7
IEC 61131-3 Supported Editor Types:................................................................................................1–8
Install Hardware............................................................................................................................... 1–9
Apply Power to CPU.......................................................................................................................1–12
Develop HMI Screens directly in the CODESYS Development Environment..................1–13
Chapter 2 - Specifications..................................................................................... 2–1
P2CDS-622 CPU...............................................................................................................................2–2
P2CDS-622 CPU Features..............................................................................................................2–4
P2CDS-622 CPU Programmable RS232/485 Ports..................................................................2–5
Table of Contents
P2CDS-622 CPU Ethernet Ports...................................................................................................2–7
P2CDS-622 CPU Micro USB Type C Programming Port........................................................2–8
P2CDS-622 CPU microSD Slot......................................................................................................2–9
microSD Slot.................................................................................................................................................2–9
P2CDS-622 CPU Battery Installation........................................................................................ 2–10
Battery (Optional) ....................................................................................................................................2–10
I/O Modules Overview..................................................................................................................2–11
Intentionally Blank Page........................................................................................................................2–15
ii
CDSYS
Hardware User Manual, 1st Edition
Getting Started
Chapter
1
In This Chapter...
Introduction...................................................................................................................................... 1–2
Purpose of this Manual .........................................................................................................................1–2
Intended Use of This Product ..............................................................................................................1–2
Benefits of P2CDS-622 with CODESYS Software..................................................................... 1–3
Conventions Used............................................................................................................................ 1–4
Key Topics for Each Chapter...................................................................................................................1–4
Important Online Resources......................................................................................................... 1–5
P2CDS-622 System.......................................................................................................................... 1–6
Preparation....................................................................................................................................................1–6
1. CODESYS IDE Install............................................................................................................................1–6
2. P2CDS-622 Firmware Install.............................................................................................................1–6
3. System Requirements and Installation........................................................................................1–6
4. Installation...............................................................................................................................................1–7
5. PLC On the Network...........................................................................................................................1–7
IEC 61131-3 Supported Editor Types:................................................................................................1–8
Install Hardware............................................................................................................................... 1–9
Apply Power to CPU.......................................................................................................................1–12
Develop HMI Screens directly in the CODESYS Development Environment..................1–13
Chapter 1: Getting Started
Introduction
Purpose of this Manual
Thank you for purchasing the AutomationDirect ProductivityCODESYS CPU. The user
manual provides information that will help you install, set up, troubleshoot, and maintain
your ProductivityCODESYS project.
The manual includes information that is critical to the safety of the personnel, who will
install and use the controller, and to the machinery, processes, and equipment controlled
by the P2CDS-622 CPU.
The manual also includes important information about power and signal wiring, mounting
the CPU and I/O modules, and configuring the system.
Intended Use of This Product
The P2CDS-622 is a Productivity®2000 format CPU allowing implementation of the
IEC-61131-3 programming languages through the use of CODESYS software. The
CODESYS system is the basis of a comprehensive suite that covers the entire software
side of automation including Industrial Internet of Things (IIoT), communication, Soft PLC,
drives, and visualization. It offers users practice-oriented, integrated solutions for the
convenient configuration of automation applications and provides practical support for
accomplishing daily tasks.
Users can develop a human machine interface (HMI) and a PLC application in one
IEC 61131-3 development system. The CODESYS Visualization tool has proven itself in
thousands of industrial machine and plant applications around the world.
Any use other than described in this manual is not permitted, as it may expose the user to
possible harm and/or damage to the device or connected equipment.
The P2CDS-622 CPU must not be altered or modified. The safety instructions as well as
the maximum permissible ambient conditions and operating parameters are given in
Chapter 2 “Specifications”.
This instruction manual is meant to be read thoroughly while being mindful of safe and
proper operation. It contains important information on mounting, operating and handling
the P2CDS-622.
1–2
CDSYS
Hardware User Manual, 1st Edition
Chapter 1: Getting Started
Benefits of P2CDS-622 with CODESYS Software
Choose your functionality
•
Visualization and communication with other systems
•
Fieldbus and I/O connection
•
Testing, debugging, analysis, version control
Choose between extensive Industry 4.0 possibilities
•
Administration platform for your controllers and projects
•
Data logging and display
•
•
•
•
•
•
•
•
Remote maintenance and remote access
Connection to external systems for Big Data/Machine Learning/AI
Static code analysis for early detection of potential programming errors
Profiling/test automation tools for facilitated acceptance according to EN13849
PLd
Creation of graphical user interfaces
Remote access for maintenance, diagnostics, monitoring, and debugging via
the associated Industry 4.0 platform
Cloud-supported analysis of operating data
Connection to public cloud systems via MQTT for predictive maintenance by
means of AI algorithm
For Building Control Systems (Local and Global)
•
•
•
•
•
•
•
Expandable panel controls, thanks to being manufacturer independent and
widely used open systems
Industry standard protocols such as Modbus
Engineering software for the creation of logical links and sequences
Convenient graphical configuration of aggregates/units for trade-specific
application
Worldwide available visualizations for monitoring and operation
Connection of external APIs and cloud providers through IoT clients for efficient
energy management, e.g. at the energy exchange
Analysis of incoming measurement data in the cloud and presentation of the
results on configurable dashboards
CDSYS
Hardware User Manual, 1st Edition
1–3
Chapter 1: Getting Started
Conventions Used
NOTE: When you see the “note pad” icon in the left-hand margin, the paragraph to its immediate
right will be a special note. Notes represent information that may make your work quicker or
more efficient. The word NOTE in boldface will mark the beginning of the text.
WARNING: When you see the “exclamation point” icon in the left-hand margin, the
paragraph to its immediate right will be a warning. This information could prevent
injury, loss of property, or even death in extreme cases. Any warning in this manual
should be regarded as critical information that should be read in its entirety. The
word WARNING in boldface will mark the beginning of the text.
Key Topics for Each Chapter
The beginning of each chapter will list the key
topics that can be found in that chapter.
1–4
CDSYS
Hardware User Manual, 1st Edition
Chapter 1: Getting Started
Important Online Resources
Download the latest version of the CODESYS Software from the CODESYS website:
https://us.store.codesys.com/codesys.html
NOTE: USB or Ethernet cable is also required for communications between PC and CPU.
Follow steps on site to log-in and download the CODESYS software system.
NOTE: CODESYS supports the software from their website. Once you establish a user account you
will be able to receive support from CODESYS.
Access to ADC Community based help for your ProductivityCODESYS projects is available
from our website: P2CDS-622. Here you will find acces to our RTD site.
A variety of other useful information about the ProductivityCodesys I/O modules, as well as
code for example tasks and more is available.
In addition, all supported Productivity2000 series power supplies and I/O modules include
a convenient installation insert.
CDSYS
Hardware User Manual, 1st Edition
1–5
Chapter 1: Getting Started
P2CDS-622 System
Preparation
The installation steps are as follows:
1. Install the CODESYS IDE on your PC.
2. Install the latest P2CDS-622 Firmware image file.
3. Install the P2CDS-622 Device Package (.package) file.
4. Configure the Ethernet ports
5. Install the IIoT Library file (optional) if needed.
1. CODESYS IDE Install
•
•
The first task is to load and install the CODESYS software. This can be found at
the following CODESYS Store location: https://us.store.codesys.com/
The remaining steps can be found at this RTD site: .
The RTD link https://docs.codesys-p2cds622.com/Getting Started/preparation.
html
There you will find all the information for getting your P2CDS-622 system up and running.
1–6
CDSYS
Hardware User Manual, 1st Edition
Chapter 1: Getting Started
P2CDS-622 System, cont’d
IEC 61131-3 Supported Editor Types:
•
Functional Block Diagram (FBD)
•
Sequential Function Charts (SFC)
•
•
Structured Text (ST)
Ladder Diagram (LD)
CODESYS (and P2CDS-622) also supports Continuous Function Charts (CFC) programming,
in addition to the aforementioned IEC61131-3 programming types.
NOTE: See Appendix A for an explanation of each Editor Type.
For most systems such as EtherNet/IP™, portable CODESYS libraries implement the protocol
stack for the fieldbus. Additionally, CODESYS offers libraries for Modbus communication
(TCP or serial).
Benefits:
•
Identical usage of the protocol stack for different fieldbus technologies
•
No external software tool required
•
•
•
•
•
Compiling / linking the stack dynamically to the application
For Industrial Ethernet systems: No additional hardware required - a standard
Ethernet port on the device for EtherNet/IP or Modbus TCP is sufficient
Seamless integration of the configurator into the CODESYS Development
System
Comprehensive integrated diagnostic functions
Integrated Commissioning and Diagnosis Functionality
Commissioning of the fieldbus system can be carried out with the Online Config Mode
even without an available application. Numerous functions for communication diagnostics
are available in the user interface and application, such as event loggers or diagnostic
information in the device tree and in the application code.
CDSYS
Hardware User Manual, 1st Edition
1–7
Chapter 1: Getting Started
Install Hardware
The Productivity®2000 CPU system components snap together to form a configured CPU
in minutes. See Chapter 5, Installation and Wiring, for more detailed hardware installation
information. What follows are the basic steps:
1. Install power supply in the base and engage locking tab.
Locked
2. Install CPU in the base and engage locking tab.
1–8
CDSYS
Hardware User Manual, 1st Edition
Chapter 1: Getting Started
3. Install I/O Modules and engage locking tabs.
4. Connect appropriate wiring to the power supply (P2-01AC) and I/O (P2-08TRS
module) in this example.
The power supply and load
are connected through
separate AC current sources.
CDSYS
Hardware User Manual, 1st Edition
1–9
Chapter 1: Getting Started
5. Connect USB cable. Programming connections may be via Ethernet cable or USB.
P2CDS-622 CPUs have a USB type C programming port.
1–10
CDSYS
Hardware User Manual, 1st Edition
Chapter 1: Getting Started
Apply Power to CPU
Ensure proper wiring and the correct voltage is available before connecting wiring to the
power supply. Once this is verified, connect power to the power supply. Once power is
applied, the CPU will perform a self-evaluation and verification.
P2-01DCAC
P2-01DCAC
P2-01AC
P2-01AC
P2-01AC
P2-01AC
100-240 VAC
12–24
VDC
12-24VDC
AC(L)
24VAC
24VAC
AC(L)
+V
ACL
AC(N)
-V
ACN
GND
GND
LOGIC
GND
LOGIC
GND
AC(N)
GNDGND
P2-01DC
LOGIC
LOGIC
GND
GND
P2-02DC
P2-02DC
P2-01DC
P2-01DC
P2-01DC: 24–48 VDC
P2-02DC: 24VDC
+V
-V
GND
+V
24-48VDC
30W
-V
24VDC
50W
+V
-V
LOGIC
GND
P2-01DC
P2-02DC
P2-01DC
P2-02DC
AC(L)
+V
AC(N)
GND
CDSYS
-V 1st Edition
Hardware User Manual,
1–11
Chapter 1: Getting Started
Develop HMI Screens directly in the CODESYS
Development Environment
CODESYS Development System comes with an integrated visualization editor, allowing HMI
development without the need for separate software interface.
Design visualization screens with direct access to all application variables thanks to the full
integration in the IEC 61131-3 Development System, with no tag list comparison required.
Visualization screens can be for machine and plant operation, for testing and
commissioning, and can be accessed simultaneously by any system with an internet
browser (PCs, tablets, smartphones, etc.).
NOTE: The P2CDS-622 is an entry level CODESYS PLC that runs on a single 600MHz core. As such,
adding complex Visualizations may affect performance.
1–12
CDSYS
Hardware User Manual, 1st Edition
Specifications
Chapter
2
In This Chapter...
P2CDS-622 CPU...............................................................................................................................2–2
P2CDS-622 CPU Features..............................................................................................................2–4
P2CDS-622 CPU Programmable RS232/485 Ports..................................................................2–5
P2CDS-622 CPU Ethernet Ports...................................................................................................2–7
P2CDS-622 CPU USB Type C Programming Port....................................................................2–8
P2CDS-622 CPU microSD Slot......................................................................................................2–9
microSD Slot.................................................................................................................................................2–9
P2CDS-622 CPU Battery Installation........................................................................................ 2–10
Battery (Optional) ....................................................................................................................................2–10
I/O Modules Overview..................................................................................................................2–11
P2CDS-622 Wiring, Installation and Safety............................................................................ 2–14
Chapter 2: Specifications
P2CDS-622 CPU
The P2CDS-622 CPU is a Productivity2000-series compatible CPU. It is compatible with all
Productivity2000 modules, with the exception of P2-RS and P1-RX remote slaves, PS-AMC
motion controllers, and the following Modules: P2-HSI, P2-HSO, P2-02HSC, and P2-SCM.
C UL US
R
CPU Specifications
User Memory
50MB (Includes program, data and
documentation)
Memory Type
Flash and Battery Backed RAM
Retentive Memory
1MB (Retain 800KB / Retain-Persistent 200KB)
Scan Time
550us (5K Boolean Logic)
Interfaces
USB IN: USB 2.0 (single port), Program, Monitor,
Debug, Firmware Update
ETHERNET: Two independent 10/100Mbps
RJ-45 connectors
PROTOCOLS: Modbus TCP and RTU Client/
Server, EtherNet/IP Scanner/Adapter, MQTT with
TLS, Email, SMTP Client
VISUALIZATION: “WebVisu” (Web Server)
RS232/485: RJ12 connector
RS232/485: 4-position Terminal Block
Data Logging
microSD card slot
Hardware Topologies
Four (4) Base Groups: Four (4), seven (7),
eleven (11), and fifteen (15) slot bases
Supported Modules: All P2 Discrete Input and
Output modules, all P2 Analog Input and Output
modules, P2-04PWM
Unsupported Modules: Remote Slaves (P1-RX,
P2-RS) and P2-HSO, P2-HSI, P2-02HSC, and
P2-SCM modules.
IEC 61131-3
Supported Editor Types
Functional Block Diagram (FBD)
Structured Text (ST)
Sequential Function Charts (SFC)
Ladder Diagram (LD)
Continuous Function Chart (CFC)
Real Time Clock Accuracy
±2s per day typical at 25°C
±10s per day maximum at 60°C
IMPORTANT!
Hot-Swapping Information
Note: This device cannot be Hot
Swapped.
2–2
CDSYS
Hardware User Manual, 1st Edition
Chapter 2: Specifications
P2CDS-622 CPU Specifications, cont’d
General Specifications
P2CDS-622 CPU
Operating Temperature
0° to 60°C (32° to 140°F)
Storage Temperature
-20° to 70°C (-4° to 158°F)
Humidity
5 to 95% (non-condensing)
Altitude
2,000 meters, max.
Pollution Degree
2
Environmental Air
No corrosive gases permitted
Vibration
IEC60068-2-6 (Test Fc)
Shock
IEC60068-2-27 (Test Ea)
Overvoltage Category
II
Heat Dissipation
4800mW
Enclosure Type
Open Equipment
Module Location
Controller slot in the local base in a
Productivity2000 System
Weight
139g (4.9 oz)
Agency Approvals
UL 61010-1 and UL 61010-2-201 File E139594,
Canada & USA
CE (EN 61131-2 EMC, EN 61010-1 and EN
61010-2-201 Safety)
CPU Run/Stop Switch
RUN position
Executes user program, run-time edits possible
STOP position
Does not execute user program, normal program load
position
CPU Status Indicators
PWR
Green LED is illuminated when power is ON
RUN
Green LED is illuminated when CPU is in
RUN mode
CPU
Red LED is illuminated during power ON
reset, power down, or watch-dog time-out
CDSYS
Hardware User Manual, 1st Edition
2–3
Chapter 2: Specifications
P2CDS-622 CPU Features
2–4
CDSYS
Hardware User Manual, 1st Edition
Chapter 2: Specifications
P2CDS-622 CPU Programmable RS232/485 Ports
The P2CDS-622 CPU RJ12 style connector and a 4-position terminal
may each be programmed for RS232 or RS485 connections. These
ports may be used for:
• Modbus RTU Master connections
• Modbus RTU Slave connections
• ASCII full or half duplex communications
• Custom Protocol Incoming and Outgoing communications
RS232 Specifications
TXD
RXD
RTS
GND
Maximum Output Load
(TXD/RTS)
Minimum Output Voltage Swing
Output Short Circuit Protection
RS232 Transmit output
RS232 Receive input
Handshaking output for modem control
(RJ12 Only)
Logic ground
3kΩ, 1000 pf
±5V
±15mA
RJ12 Connector Specifications
Description
Data Rates
+5V Cable Power
Port Status LED
Cable Options
CDSYS
Programmable RS232/485 Port
- Non-isolated RS232 DTE port connects the CPU as a
Modbus/ASCII master or slave to a peripheral device.
Includes ESD and built in surge protection
- Non-isolated RS485 port connects the CPU as a
Modbus/ASCII master or slave to a peripheral device.
Includes ESD/EFT protection and automatic echo
cancellation when transmitter is active
Selectable, 1200, 2400, 4800, 9600, 19200, 33600,
38400, 57600, and 115200
210mA maximum at 5V, ±5%. Reverse polarity and
overload protected.
Green LED illuminated when active for TXD, RXD and
RTS
EA-MG-PGM-CBL
D2-DSCBL
USB-RS232 with D2-DSCBL
FA-CABKIT
Hardware User Manual, 1st Edition
2–5
Chapter 2: Specifications
P2CDS-622 CPU Programmable RS485/232 Ports
RS485 Specifications
TXD+/RXD+
RS485 transceiver high
TXD-/RXDGND
Input Impedance
Electrical Fast Transient Protection
Minimum Differential Output Voltage
Fail Safe Inputs
RS485 transceiver low
Logic Ground
19kΩ
120Ω. To use, add jumper between pin 1
and pin 2. Resistor is internally connected
between pins 1 and 3.
50 transceivers, 19kΩ each, 60Ω termination
±250mA, thermal shut-down protection
Contact ±4KV, Air ±8KV per IEC61000-4-2
(Cable is installed for testing)
±1KV per IEC61000-4-4
1.5 V with 60Ω load
Logic high input state if inputs are connected
Maximum Common Mode Voltage
-7.5 V to 12.5 V
Termination Resistance
(TB Jumper wire "T" to "+")
Maximum Load
Output Short Circuit Protection
Electrostatic Discharge Protection
Terminal Block Specifications
Description
Programmable RS485/232 Port
- Non-isolated RS232 DTE port connects the CPU as a Modbus/
ASCII master or slave to a peripheral device. Includes ESD and
built in surge protection
- Non-isolated RS485 port connects the CPU as a Modbus/ASCII
master or slave to a peripheral device.
Includes ESD/EFT protection and automatic echo cancellation
when transmitter is active
Data Rates
Selectable, 1200, 2400, 4800, 9600, 19200, 33600, 38400,
57600, and 115200
Port Status LED
Green LED illuminated when active for TXD and RXD
Cable Options
Go to AutomationDirect.com for RS232 and 485 cable selection.
4 Position Terminal Block
2–6
CDSYS
Hardware User Manual, 1st Edition
Chapter 2: Specifications
P2CDS-622 CPU Ethernet Ports
Ethernet Port (RJ45 style connectors on bottom of CPU) used
for:
• Connection to a PC running the programming software
• Modbus TCP Client (64 Servers) connections (Modbus requests
sent from the CPU)
• Modbus TCP Server (16 Clients) connections (Modbus requests
received by the CPU)
• EtherNet/IP Scanner (64 Adapters)
• EtherNet/IP Adapter (4 scanners) with 8 connections per device.
• Outgoing E-mail
• MQTT Client (4 brokers)
• Rear port does not have Default Gateway or DNS capability.
Ethernet Specifications
Port Name
ETHERNET
Description
Standard transformer isolated Ethernet port with built-in surge
protection for programming, online monitoring, firmware, MQTT,
Email (SMTP client), Modbus/TCP client/server connections
(fixed IP or DHCP) and Ethernet/IP Scanner/Adapter
connections.
Transfer
Rate
RJ45 Yellow LED
Off = 10Mbps / On = 100 Mbps
Port Status
LED
RJ45 Green LED
Solid when network LINK is established.
Flashes when port is active (ACT).
P2CDS-622 Bottom View
CDSYS
Hardware User Manual, 1st Edition
2–7
Chapter 2: Specifications
P2CDS-622 CPU USB Type C Programming Port
The P2CDS-622 CPU has a standard USB C Slave input for programming and online
monitoring, with built-in surge protection. Capable of 480Mbps.
USB Type C Specifications
Port Name
Description
USB C
Standard USB C Slave input for programming and online
monitoring, with built-in surge protection.
Transfer Rate
480Mbps
Port Status LED
Green LED is illuminated when LINK is established to
programming software.
USB Type A to USB Type C:
6ft cable part # USB-CBL-AC6
Cables
P2CDS-622
2–8
CDSYS
Hardware User Manual, 1st Edition
Chapter 2: Specifications
P2CDS-622 CPU microSD Slot
microSD Slot
The SD Card can be used for the Data Logging in the project or program transfer.
When an SD Card is inserted, the “μSD” LED will flash green a few times then stay on steady
green.
The “Unmount” button is pressed prior to removing the SD card. When pressed, the μSD
port LED flashes momentarily during the unmounting and then will be off indicating it is
safe to remove the SD Card.
Pin
Pin
1
SDSD
1
2
3
4
5
6
7
8
DAT2
DAT2
CD/
CD/DAT3
DAT3
CMDCMD
VDDVDD
CLK CLK
VSS VSS
DAT0
DAT0
DAT1
DAT1
Hardware User Manual, 1st Edition
2–9
1
8
2
3
4
5
6
7
8
microSD Specifications
Port Name
microSD
Description
Standard microSD socket for data logging or program
transfer
Maximum Card
Capacity
Transfer Rate
(ADATA microSDHC
Class 4 memory card)
Port Status LED
32GB
Mbps
Minimum
Typical
Maximum
Read
14.3
14.4
14.6
Write
4.8
4.9
5.1
Green LED is illuminated when card is inserted and
detected
CDSYS
Chapter 2: Specifications
P2CDS-622 CPU Battery Installation
Battery (Optional)
A battery is included with the CPU module but is not installed. The battery may be
installed in order to retain the Time and Date along with any tagname values that
are set up as retentive. The battery is not needed for program backup.
Battery (Optional)
D2-BAT-1
Coin type, 3.0 V Lithium battery, 560mA, battery number
CR2354
Note: Although not needed for program backup, an uninstalled battery is
included with the P2CDS-622. Install this battery if you want the CPU to
retain the Time and Date along with any Tagname values that you have
configured as retentive.
2–10
CDSYS
Hardware User Manual, 1st Edition
Chapter 2: Specifications
I/O Modules Overview
A variety of analog I/O modules from our Productivity2000 line are available for use
with the P2CDS-622 CPU. Please refer to Productivity2000 manual Chapter 2 for detailed
technical specifications.
Productivity®2000
I/O Modules Supported
Part Number
Number
of Points
Description
Discrete Input Modules
Discrete Input Modules
Discrete Output Modules
P2-08SIM
8
Input Simulator Module
P2-08ND3-1
8
Sinking/Sourcing 12–24 VDC
P2-16ND3-1
16
Sinking/Sourcing 12–24 VDC
P2-32ND3-1
32
Sinking/Sourcing 12–24 VDC
P2-08NE3
8
Sinking/Sourcing 24V AC/DC
P2-16NE3
16
Sinking/Sourcing AC/DC
P2-32NE3
32
Sinking/Sourcing 24V AC/DC
P2-08NAS
8
AC Isolated 100–120 VAC
P2-16NA
16
AC Isolated 100–240 VAC
Discrete Output Modules
P2-08TD1S
8
Isolated Sinking
P2-08TD2S
8
Isolated Sourcing
P2-15TD1
15
Sinking
P2-15TD2
15
Sourcing
P2-08TD1P
8
Sinking, Protected
P2-08TD2P
8
Sourcing, Protected
P2-16TD1P
16
Sinking, Protected
P2-16TD2P
16
Sourcing, Protected
P2-32TD1P
32
Sinking, Protected
P2-32TD2P
32
Sourcing, Protected
P2-08TAS
8
Isolated AC
P2-16TA
16
AC Output
P2-08TRS
8
Isolated Relay
P2-16TR
16
Relay Output
CDSYS
Hardware User Manual, 1st Edition
2–11
Chapter 2: Specifications
I/O Modules Overview, continued
Productivity®2000
I/O Modules Supported
Part Number
Description
Analog Input Modules

 




 


Analog Input Modules
P2-04AD
4
Voltage/Current
P2-04AD-1
4
Current
P2-04AD-2
4
Voltage
P2-08AD-1
8
Current
P2-08AD-2
8
Voltage
P2-08ADL-1*
8
Current
P2-08ADL-2*
8
Voltage
P2-16AD-1
16
Current
P2-16AD-2
16
Voltage
P2-16ADL-1*
16
Current
P2-16ADL-2*
16
Voltage
P2-06RTD
6
RTD Input
P2-08THM
8
Thermocouple Input
P2-08NTC
8
Thermistor Input
Analog Output Modules
1 18.23
2 14.23
3
4.00
4
4.23
5 13.56
6 16.32
7
8.00
8
7.54
Analog Output Modules
2–12
Number
of Points
CDSYS
P2-04DA
4
Voltage/Current
P2-04DA-1
4
Current
P2-04DA-2
4
Voltage
P2-04DAL-1*
4
Current
P2-04DAL-2*
4
Voltage
P2-08DA-1
8
Current
P2-08DA-2
8
Voltage
P2-08DAL-1*
8
Current
P2-08DAL-2*
8
Voltage
P2-16DA-1
16
Current
P2-16DA-2
16
Voltage
P2-16DAL-1*
16
Current
P2-16DAL-2*
16
Voltage
Hardware User Manual, 1st Edition
Chapter 2: Specifications
I/O Modules Overview, continued
1I00.00
2I04.00
3I00.00
4I04.00
5I00.00
6I04.00
7I00.00
8I SPARE
Productivity®2000
I/O Modules Supported
Part Number
Number
of Points
Description
Analog Combination Modules
P2-08AD4DA-1
8/4
Analog Input/Output (Current)
P2-8AD4DA-2
8/4
Analog Input/Output (Voltage)
Combination
Analog I/O Module
Specialty Modules
Part Number
Description
P2-04PWM
High-speed pulse-width
modulation
NOTE: Unsupported Modules: Remote Slaves (P2-RS) and Intelligent
modules (P2-HSO, P2-HSI, P2-02HSC, and P2-SCM.
CDSYS
Hardware User Manual, 1st Edition
2–13
Chapter 2: Specifications
P2CDS-622 Wiring, Installation and Safety
P2CDS-622 is supported by Productivity2000 system hardware and has the same
installation and safety guidelines. Please refer to Chapter 5 “Installation and Wiring” in the
P2000 user manual for details concerning installation procedures and wiring suggestions.
2–14
CDSYS
Hardware User Manual, 1st Edition
">