Epson | EB-G6050W Guide | User`s guide | Epson EB-G6050W Guide User`s guide

User's Guide
Organization of the Guide and Notations in the Guide
Using Each Guide
The guides for this projector are organized as shown below.
Safety Instructions/Support and Service Guide
Contains information on using the projector safely, as well as a support and service guide,
troubleshooting check lists, and so on. Make sure you read this guide before using the pro‐
jector.
User's Guide (this guide)
Contains information on setting up and basic operations before using the projector, using
the Configuration menu, and handling problems and performing routine maintenance.
Quick Start Guide
Contains information on the procedures for setting up the projector. Read this first.
3D Glasses User's Guide
Contains information on handling the 3D Glasses and warnings and so on.
WirelessHD Transmitter User's Guide (EH-TW6600W only)
Contains information on handling the WirelessHD Transmitter and warnings and so on.
1
Organization of the Guide and Notations in the Guide
Notations Used in This Guide
Safety Indications
The documentation and the projector use graphical symbols to show how to use the projector safely.
The following shows the symbols and their meanings. Please understand and respect these caution symbols
in order to avoid injury to persons or property.
Warning
This symbol indicates information that, if ignored, could possibly result in personal injury or even death
due to incorrect handling.
Caution
This symbol indicates information that, if ignored, could possibly result in personal injury or physical
damage due to incorrect handling.
General Information Indications
Attention
Indicates procedures which may result in damage or malfunctions to occur.
c
s
Menu Name
Indicates additional information and points which may be useful to know regarding a topic.
Indicates a page where detailed information regarding a topic can be found.
Indicates Configuration menu items.
Example: Image - Color Mode
Button Name
Indicates the buttons on the remote control or the control panel.
Example:
button
About the Use of "This Product" or "This Projector"
As well as the main projector unit, supplied items or optional extras may be referred to using the phrase "this
product" or "this projector".
2
Contents
Removing the Terminal Cover . . . . . . . . . . . . . . 22
Organization of the Guide and
Notations in the Guide
Preparing the Remote Control . . . . . . . . 23
Installing the Remote Control Batteries . . . . . . . 23
Using Each Guide . . . . . . . . . . . . . . . . . . . . . 1
Remote Control Operating Range . . . . . . . . . . . 23
Notations Used in This Guide . . . . . . . . . . . 2
Operating range (left to right) . . . . . . . . . . . . 23
Safety Indications . . . . . . . . . . . . . . . . . . . . . . . 2
Operating range (top to bottom) . . . . . . . . . . 23
General Information Indications . . . . . . . . . . . . . 2
About the Use of "This Product" or "This Projector"
..................................... 2
Basic Operations
Starting and Ending Projection . . . . . . . 24
Introduction
Turning on the Projector and Projecting . . . . . . 24
Part Names and Functions . . . . . . . . . . . . . 6
If the Target Image is not Projected . . . . . . . . . . 25
Front/Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Turning Off . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Adjusting the Projected Screen . . . . . . . 27
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . 8
Displaying the Test Pattern . . . . . . . . . . . . . . . . 27
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Adjusting the Focus . . . . . . . . . . . . . . . . . . . . . 27
Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Adjusting the Projection Size (Zoom
Adjustment) . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Appearance . . . . . . . . . . . . . . . . . . . . . . . . . 12
Adjusting the Projector's Tilt . . . . . . . . . . . . . . . 28
Adjusting the Position of the Projected Image
(Lens Shift) . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Preparing
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Making adjustments using the lens shift dial
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Projected Image and Position of Projector . . . . . 13
Correcting Keystone Distortion (H/V-Keystone)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Installing in parallel with the screen . . . . . . . . 13
Installing the projector horizontally by
adjusting the height of either side . . . . . . . . . 13
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . 31
Hiding the Image and Muting the Audio
Temporarily . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Various Setting Methods . . . . . . . . . . . . . . . . . 14
Placing on a table and projecting . . . . . . . . . 14
Suspending from the ceiling and projecting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Adjusting the Image
Adjusting the Image . . . . . . . . . . . . . . . . . 32
Projection Distance and Lens Shift Maximum
Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Selecting the Projection Quality (Color Mode)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Connecting a Device . . . . . . . . . . . . . . . . . 18
Switching the Screen Between Full and Zoom
(Aspect) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Connecting Video Equipment . . . . . . . . . . . . . . 18
Connecting a Computer . . . . . . . . . . . . . . . . . . 19
Absolute Color Adjustments . . . . . . . . . . 35
Connecting External Devices . . . . . . . . . . . . . . . 19
Adjusting Hue, Saturation, and Brightness . . . . . 35
Connecting to the Trigger Out port . . . . . . . . 19
Adjusting the Gamma . . . . . . . . . . . . . . . . . . . 35
Connecting to the Audio Out port . . . . . . . . . 19
Select and adjust the correction value . . . . . . 36
Connecting smartphones or tablets . . . . . . . . 20
Connecting USB devices . . . . . . . . . . . . . . . . 20
Adjust using the gamma adjustment graph
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Connecting WirelessHD devices (EHTW6600W only) . . . . . . . . . . . . . . . . . . . . . . 21
Adjusting the RGB (Offset/Gain) . . . . . . . . . . . . 36
Color Temp. . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Attaching the Wireless LAN unit . . . . . . . . . . . . 22
3
Contents
Skin Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Operating the Remote Control . . . . . . . . . . . . . 62
Detailed Image Adjustments . . . . . . . . . . 38
Remote Control Operating Range . . . . . . . . . . . 63
Adjusting the Sharpness . . . . . . . . . . . . . . . . . . 38
Switching the Input and Output . . . . . . . . . . . . 63
Setting Auto Iris . . . . . . . . . . . . . . . . . . . . . . . . 39
Switching the target image . . . . . . . . . . . . . . 63
Super-resolution and Detail Enhancement
Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Switching the image source . . . . . . . . . . . . . 65
Displaying as a Sub-Screen . . . . . . . . . . . . . . . . 67
Panel Alignment . . . . . . . . . . . . . . . . . . . . . . . 40
Using the HDMI Link Function . . . . . . . . 68
Image Processing . . . . . . . . . . . . . . . . . . . . . . . 41
HDMI Link Function . . . . . . . . . . . . . . . . . . . . . 68
Viewing the Image at the Saved Image
Quality (Memory Function) . . . . . . . . . . . 43
HDMI Link Settings . . . . . . . . . . . . . . . . . . . . . . 68
Device Connections . . . . . . . . . . . . . . . . . . . . . 69
Saving Function . . . . . . . . . . . . . . . . . . . . . . . . 43
Playing Back Image Data (Slideshow)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Saving a Memory . . . . . . . . . . . . . . . . . . . . . . . 43
Loading a Memory . . . . . . . . . . . . . . . . . . . . . . 44
Compatible Data . . . . . . . . . . . . . . . . . . . . . . . 70
Deleting a Saved Memory . . . . . . . . . . . . . . . . . 44
Playing a Slideshow . . . . . . . . . . . . . . . . . . . . . 70
Renaming a Memory . . . . . . . . . . . . . . . . . . . . 44
Display Settings for Image Files and Slideshow
Operation Settings . . . . . . . . . . . . . . . . . . . . . . 71
Useful Functions
Projecting Two Different Images Using
Picture in Picture . . . . . . . . . . . . . . . . . . . . 72
Enjoying 3D Images . . . . . . . . . . . . . . . . . . 46
Types of Screen that can be Displayed
Simultaneously . . . . . . . . . . . . . . . . . . . . . . . . 72
Setting 3D Images . . . . . . . . . . . . . . . . . . . . . . 46
When the projector detects a 3D format . . . . 46
Projecting on a Picture in Picture . . . . . . . . . . . . 72
When the projector cannot detect a 3D
format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Starting and exiting Picture in Picture . . . . . . 72
Changing the Picture in Picture settings . . . . 73
If the 3D image cannot be viewed . . . . . . . . . 46
Using 3D Glasses . . . . . . . . . . . . . . . . . . . . . . . 47
Charging the 3D Glasses . . . . . . . . . . . . . . . . 47
Configuration Menu
Pairing 3D Glasses . . . . . . . . . . . . . . . . . . . . 47
Configuration Menu Functions . . . . . . . . 74
Wearing the 3D Glasses . . . . . . . . . . . . . . . . 48
Configuration Menu Operations . . . . . . . . . . . . 74
Reading the indicator on the 3D Glasses . . . . 49
Configuration Menu Table . . . . . . . . . . . . . . . . 75
Range for Viewing 3D Images . . . . . . . . . . . . . . 49
Image menu . . . . . . . . . . . . . . . . . . . . . . . . 75
Warnings Regarding Viewing 3D Images . . . . . . 50
Signal menu . . . . . . . . . . . . . . . . . . . . . . . . 77
Converting 2D Images to 3D and Viewing . . . . . 52
Settings menu . . . . . . . . . . . . . . . . . . . . . . . 79
Connecting with WirelessHD (EHTW6600W Only) . . . . . . . . . . . . . . . . . . . . . 54
Memory menu . . . . . . . . . . . . . . . . . . . . . . . 84
Installing the WirelessHD Transmitter . . . . . . . . 54
Info menu . . . . . . . . . . . . . . . . . . . . . . . . . . 87
WirelessHD Transmitter part names . . . . . . . . 54
Reset menu . . . . . . . . . . . . . . . . . . . . . . . . . 87
WirelessHD Transmitter connection
example and signal flow . . . . . . . . . . . . . . . . 56
Picture in Picture menu . . . . . . . . . . . . . . . . 88
Network menu . . . . . . . . . . . . . . . . . . . . . . . 84
Troubleshooting
Setting the WirelessHD Transmitter . . . . . . . . 58
Projecting Images . . . . . . . . . . . . . . . . . . . . . . 59
Problem Solving . . . . . . . . . . . . . . . . . . . . . 89
WirelessHD Settings Menu . . . . . . . . . . . . . . . . 60
Reading the Indicators . . . . . . . . . . . . . . . . . . . 89
WirelessHD Transmission Range . . . . . . . . . . . . 61
Indicator status during an error/warning . . . . 89
4
Contents
Indicator status during normal operation . . . . 91
MHL Input Signal . . . . . . . . . . . . . . . . . . . . . . 111
When the Indicators Provide No Help . . . . . . . . 92
3D Input Signal HDMI . . . . . . . . . . . . . . . . . . . 111
Check the problem . . . . . . . . . . . . . . . . . . . . 92
WirelessHD Input Signal . . . . . . . . . . . . . . . . . 111
Problems relating to images . . . . . . . . . . . . . 93
3D Input Signal MHL (via a WirelessHD
Transmitter*) . . . . . . . . . . . . . . . . . . . . . . . . . 112
Problems when projection starts . . . . . . . . . . 96
Problems with the remote control . . . . . . . . . 96
Specifications . . . . . . . . . . . . . . . . . . . . . . 113
Problems with the control panel . . . . . . . . . . 97
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Problems with 3D . . . . . . . . . . . . . . . . . . . . 97
General Notes . . . . . . . . . . . . . . . . . . . . . . 119
Problems with HDMI . . . . . . . . . . . . . . . . . . 98
General Notice . . . . . . . . . . . . . . . . . . . . . . . . 119
Problems with WirelessHD (EH-TW6600W
only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Problems with USB storage devices . . . . . . . 100
Other problems . . . . . . . . . . . . . . . . . . . . . 100
Event ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Maintenance
Maintenance . . . . . . . . . . . . . . . . . . . . . . . 102
Cleaning the Parts . . . . . . . . . . . . . . . . . . . . . 102
Cleaning the air filter . . . . . . . . . . . . . . . . . 102
Cleaning the main unit . . . . . . . . . . . . . . . . 103
Cleaning the lens . . . . . . . . . . . . . . . . . . . . 104
Cleaning the 3D Glasses . . . . . . . . . . . . . . . 104
Replacement Periods for Consumables . . . . . . 104
Air filter replacement period . . . . . . . . . . . . 104
Lamp replacement period . . . . . . . . . . . . . . 104
Replacing Consumables . . . . . . . . . . . . . . . . . 105
Replacing the air filter . . . . . . . . . . . . . . . . . 105
Replacing the lamp . . . . . . . . . . . . . . . . . . 106
Resetting lamp hours . . . . . . . . . . . . . . . . . 108
Appendix
Optional Accessories and
Consumables . . . . . . . . . . . . . . . . . . . . . . . 109
Optional Items . . . . . . . . . . . . . . . . . . . . . . . . 109
Consumables . . . . . . . . . . . . . . . . . . . . . . . . . 109
Supported Resolutions . . . . . . . . . . . . . . 110
Component Video . . . . . . . . . . . . . . . . . . . . . 110
Composite Video . . . . . . . . . . . . . . . . . . . . . . 110
Computer Signals (Analog RGB) . . . . . . . . . . . 110
HDMI1/HDMI2 Input Signal . . . . . . . . . . . . . . . 110
5
Introduction
Part Names and Functions
Front/Top
Name
a Lamp cover
b Air exhaust vent
Function
Open when replacing the projector's lamp. s p.106
Exhaust vent for air used to cool the projector internally.
Caution
While projecting, do not put your face or hands near the air exhaust vent,
and do not place objects that may become warped or damaged by heat near
the vent. Hot air from the air exhaust vent could cause burns, warping, or
accidents to occur.
c Focus ring
d Lens cap
Adjusts the image focus. s p.27
e Projector's lens
f Zoom ring
Images are projected from here.
g Remote receiver
h Front adjustable
foot
Receives signals from the remote control. s p.23
i Air filter cover
When cleaning or replacing the air filter, open this cover and remove the air filter.
s p.102, p.105
Air intake vent
Install when not using the projector to protect the lens from being scratched or
soiled. s p.24
Adjusts the image size. s p.27
When setup on a surface such as a table, extend the foot to adjust the horizontal
tilt. s p.28
Intake vent for air used to cool the projector internally.
j Vertical lens shift dial Turn the dial to move the position of the projected image up or down. s p.28
k Horizontal lens shift Turn the dial to move the position of the projected image left or right. s p.28
dial
6
Introduction
Name
l Control panel
Function
Control panel on the projector. s p.7
Control Panel
Buttons/Indicators
Function
a
Flashes orange when it is time to replace the lamp. Shows the projector's errors
through a combination of other indicators lit and flashing. s p.89
b
Flashes to indicate warm-up in progress or cool-down in progress. Shows the
projector's status through a combination of other indicators lit and flashing.
s p.89
Operation indicator
c
Turns the projector power on or off. s p.24
Lit when the projector is on. s p.91
d
Changes to the image from each input port. s p.25
e
Selects the adjustment value for the volume and for menu items. s p.31
Performs horizontal keystone correction when the Keystone screen is dis‐
played. s p.30
f
Selects adjustment values for menu items. s p.30
Performs vertical keystone correction when the Keystone screen is displayed.
s p.30
g
Detects the brightness of the room. When Color Mode is set to "Auto", the
optimum image quality is set according to the brightness detected by the sen‐
sor. s p.32
Brightness sensor
h
Returns to the previous menu level when a menu is displayed. s p.74
i
Selects functions and settings when a menu is displayed. s p.74
j
Displays and closes the Configuration menu.
On the Configuration menu, you can make adjustments and settings for Signal,
Image, and so on. s p.74
k
Flashes orange if the internal temperature is too high. Shows the projector's
errors through a combination of other indicators lit and flashing. s p.89
7
Introduction
Remote Control
Button
Function
a
Turns the projector on. s p.24
b
Allows you to simultaneously project two im‐
age sources, one in the main screen and the
other in the sub screen. (Picture in Picture)
s p.72
Press and hold the button to swap the main
or sub screen image sources.
c
Changes to the image from each input port.
s p.25
button is only available for EHTW6600W.
d
This button displays the settings menu for
HDMI Link.
With the other buttons, you can then start or
stop playback, and so on for connected devi‐
ces that meets the HDMI CEC standards or the
MHL standards. s p.68
e
Changes the 3D format.
This projector supports the following 3D for‐
mats.
• Frame Packing
• Side by Side
• Top and Bottom
s p.46
f
Selects menu items and adjustment values.
s p.74
g
The adjustment value returns to its default
value when pressed while the menu's adjust‐
ment screen is displayed. s p.74
h
Displays and closes the Configuration menu.
On the Configuration menu, you can make
adjustments and settings for Signal, Image,
and so on. s p.74
i
Smoothly projects images with a quick frame
rate, such as games. s p.41
8
Introduction
Button
Function
j
Performs the function assigned to the user
button. s p.79
k
Saves, loads, or erases a memory. s p.43
l
(Only available for EH-TW6600W)
WiHD Transmitter control
Turns on the WirelessHD Transmitter, or
switches the input and output.
Make sure you point the remote control at the
WirelessHD Transmitter when performing
operations. s p.62
m
Displays and closes the test pattern. s p.27
n
Temporarily hides or shows the image and
audio. s p.31
o
Changes between 2D and 3D. s p.46
p
Selects the aspect mode according to the in‐
put signal. s p.33
q
Adjusts the hue, saturation, and brightness
for each RGBCMY color. s p.35
r
Returns to the previous menu level when a
menu is displayed. s p.74
s
When a menu is displayed, it accepts and en‐
ters the current selection and moves to the
next level. s p.74
t
Sets Super-resolution that makes fuzzy out‐
lines clear, or Detail Enhancement that em‐
phasizes the texture and material feel of im‐
ages. s p.39
A
Changes the Color Mode. s p.32
B
Adjusts the volume. s p.31
C
Temporarily hides or shows the image and
audio. s p.31
D
The remote control buttons light up for ap‐
proximately 10 seconds. This is useful when
operating the remote control in the dark.
E
Turns the projector off. s p.25
9
Introduction
Rear
Name
Function
a Speaker
The projector's built-in speaker. Outputs audio. Set Inverse Audio to On to
use the built-in speaker when the projector is suspended from a ceiling.
s Settings - Audio - Inverse Audio p.79
b Power inlet
c Trigger Out port
Connect the power cord. s p.24
d RS-232C port
When controlling the projector, connect the projector to a computer with an
RS-232C cable. This port is for control use and should not normally be used.
s p.113
e Audio (L-R) port
Inputs audio from equipment connected to the Video port, the Component
ports, or the PC port. s p.18
f Component port
Connects to the component (YCbCr or YPbPr) output port on video equip‐
ment. s p.18
g Security slot (
The security slot compatible with the MicroSaver security system manufac‐
tured by Kensington. For more details, visit the homepage of Kensington at
http://www.kensington.com/.
)
Connects with external devices such as motorized screens. s p.19
h Audio Out port
i Cable holder
Outputs audio during playback to external speakers. s p.19
j Remote receiver
k USB port (TypeA)
Receives signals from the remote control. s p.23
l Service port
m Video port
Service port. This is not normally used.
n HDMI2 port
o PC port
Connects HDMI compatible video equipment and computers. s p.18
p HDMI1 port
Connects HDMI compatible video equipment and computers. s p.18
In addition, connects MHL compatible smart devices or tablets. s p.19
When a cable is connected to a port, the weight of the cable may result in
imperfect insertion of its connector. In order to prevent this, put a commer‐
cially available clamping band (cable tie) through this holder to bind and fix
the cable.
Connects USB devices such as a USB memory device or a digital camera, and
projects images as a slideshow. s p.70
In addition, connects an optional wireless LAN unit. s p.22
Connects to the composite video output port on video equipment. s p.18
Connects to the RGB output port on a computer. s p.19
10
Introduction
Base
Name
Function
a Front adjustable foot When setup on a surface such as a table, extend the foot to adjust the horizontal
tilt. s p.28
b Ceiling mount fixing Attaches the optional ceiling mount here when suspending the projector from a
points (four points) ceiling. s p.109
c Air intake vent
When suspending from a ceiling, make sure it is setup so that dust does not collect
in this section.
11
Introduction
Appearance
Units: mm
a
b
Center of lens
Distance from center of lens to suspension bracket fixing point
12
Preparing
Installing
Projected Image and Position of Projector
Install the projector as follows.
Installing in parallel with the screen
If the projector is installed at an angle to the screen, keystone distortion occurs in the projected image.
Adjust the projector’s position so that it is installed in parallel with the screen.
c
• If the projector cannot be installed in front of the screen, you can adjust the position of the image by
using lens shift. s p.28
• Use keystone correction when you cannot make adjustments using lens shift. s p.30
Installing the projector horizontally by adjusting the height of either side
If the projector is tilted, the projected image is also tilted.
Install the projector horizontally so that both sides are at the same height.
If the projector cannot be installed horizontally, you can adjust the projector's tilt with the front foot. s p.28
13
Preparing
Various Setting Methods
Warning
• A special method of installation is required when suspending the projector from a ceiling (ceiling mount). If
it is not installed correctly, it could fall causing an accident and injury.
• If you use adhesives, lubricants, or oil on the ceiling mount fixing points to prevent screws from loosening,
or if you use things such as lubricants or oils on the projector, the projector case may crack causing it to fall
from its ceiling mount. This could cause serious injury to anyone under the projector and also damage the
projector.
• Do not install it on an unstable shelf or in a place out of load range. Otherwise, it could fall or topple causing
an accident and injury.
• When installing it in a high position such as on a shelf, take measures against falling by using wires to ensure
the safety in an emergency, such as an earthquake, and prevent accidents. If it is not installed correctly, it
could fall causing an accident and injury.
• Do not block the air intake vent and air exhaust vent of the projector. Blocking its air intake vent and air
exhaust vent may trap heat inside causing fire.
Attention
• Try not to setup the projector in locations subject to high humidity and dust, or in locations subject to smoke
from fires or tobacco smoke.
• Do not use the projector installed vertically. Doing so could cause a malfunction.
• Clean the air filter once every three months. Clean it more often if the environment is particularly dusty.
s p.102
c
• If the projector cannot be installed in front of the screen, you can adjust the position of the image by
using lens shift. s p.28
• Use keystone correction when you cannot make adjustments using lens shift. s p.30
Placing on a table and projecting
You can install the projector on a table in your living room or on a low shelf to project images.
14
Preparing
Suspending from the ceiling and projecting
You can suspend the projector from the ceiling with the optional ceiling mount to project images.
c
• When projecting from a ceiling, change Projection to a ceiling setting. s Settings - Projection p.79
• Set Inverse Audio to On to use the built-in speaker when the projector is suspended from a ceiling.
s Settings - Audio - Inverse Audio p.79
Projection Distance and Lens Shift Maximum Values
The size of the projection increases as the projector is moved away from the screen. Use the table below to
setup the projector at the optimum position from the screen. The values given here are for your reference only.
The maximum lens shift adjustment values are shown in the following table.
When adjusting the projection position vertically in lens shift
A :
B
:
E
F
:
:
Distance from the center of the lens to the bottom edge of the projected image (when lens shift is raised
to its highest level)
Distance from the center of the lens to the bottom edge of the projected image (when lens shift is lowered
to its lowest level)
Projection distance from the projector to the screen
Size of the projected image
15
Preparing
When adjusting the projection position horizontally in lens shift
C
D
E
F
:
:
:
:
Lens center movement distance when the projector is moved (when lens shift is set to maximum left)
Lens center movement distance when the projector is moved (when lens shift is set to maximum right)
Projection distance from the projector to the screen
Size of the projected image
Unit: cm
16:9 Screen Size
F
WxH
Lens Shift Maximum Values*
Projection Distance (E)
Minimum
(Wide)
Maximum
(Tele)
Distance
(A)
Distance
(B)
Distance
(C, D)
40"
89 x 50
116
190
5
55
21
60"
130 x 75
176
286
7
82
32
80"
180 x 100
235
382
10
110
43
100"
220 x 120
295
478
12
137
53
120"
270 x 150
354
575
15
164
64
150"
330 x 190
443
719
19
205
80
180"
440 x 250
532
863
22
247
96
16
Preparing
Unit: cm
4:3 Screen Size
F
WxH
Lens Shift Maximum Values*
Projection Distance (E)
Minimum
(Wide)
Maximum
(Tele)
Distance
(A)
Distance
(B)
Distance
(C, D)
40"
81 x 61
143
233
6
67
26
60"
120 x 90
216
351
9
101
39
80"
160 x 120
288
468
12
134
52
100"
200 x 150
361
586
15
168
65
120"
240 x 180
434
704
18
201
78
150"
300 x 230
443
719
23
251
98
200"
410 x 300
591
1175
30
335
* Vertical and horizontal lens shift cannot both be set to their maximum values. s p.28
Installation example (with 16:9 screen size and 100")
Side view
Overhead view
17
130
Preparing
Connecting a Device
Attention
• Make cable connections before connecting to a power outlet.
• When disconnecting, turn off the projector first, then remove the power cord, and then disconnect other
cables.
• Check the shape of the cable's connector and the shape of the port, and then connect. If you force a connector
of a different shape into the port, it could cause damage and a malfunction to occur.
EH-TW6600W comes with an terminal cover allowing you to clearly see the connector section on the rear.
Remove the terminal cover before connecting any cables. s p.22
Connecting Video Equipment
To project images from DVD players or VHS video and so on, connect to the projector using one of the
following methods.
When using an HDMI cable
When using a video cable
When using a component video cable
c
• The cable differs depending on the output signal from the connected video equipment.
• Some types of video equipment are capable of outputting different types of signals. Check the user's
guide supplied with the video equipment to confirm which signals can be output.
• You can also connect your AV system to enjoy the audio from connected equipment.
18
Preparing
Connecting a Computer
To project images from a computer, connect the computer using one of the following methods.
When using a computer cable
When using an HDMI cable
Connecting External Devices
Connecting to the Trigger Out port
To connect external devices such as motorized screens, connect a mini-jack stereo cable (3.5 mm) to the
Trigger Out port.
When set to on, a signal (12 V DC) is output from this port to communicate the projector's status (on or off)
to connected devices such as electric screens.
c
When using the Trigger Out port, set the Trigger Out function. s Settings - Operation - Trigger
Out p.79
Connecting to the Audio Out port
To connect external devices such as external speakers, connect a commercially available audio cable.
c
• Do not connect headphones.
• When the projector is in standby status, no audio can be output.
19
Preparing
Connecting smartphones or tablets
You can connect MHL compatible smartphones or tablets.
Use an MHL compatible cable to connect the micro USB port of smartphones and tablets to the HDMI1 port
on the projector.
You can also view video and listen to music while charging a smartphone or tablet.
Attention
• Make sure the connection cable supports the MHL standards. During charging, the smartphone or tablet
could generate heat, cause a liquid leak, explode or generate other conditions that could result in a fire.
• When a connection is made using an MHL-HDMI conversion adapter, it may not be possible to charge or
control the device from the remote control.
c
• Some devices use more power during video playback than what is supplied and will therefore not
enable charging during video playback or other operations.
• When the projector is in standby status or when a smartphone or tablet has no remaining battery level,
it cannot be charged.
Connecting USB devices
You can connect USB devices such as USB memories, and USB compatible digital cameras.
Using the USB cable supplied with the USB device, connect the USB device to the USB port (TypeA) on the
projector.
When the USB device is connected, you can project image files on the USB memory or digital camera as a
slideshow. s p.70
When you have finished projecting, remove USB devices from the projector. For devices with a power switch,
make sure you turn them off before disconnecting the USB device.
Attention
• If you use a USB hub, the connection may not operate correctly. Devices such as digital cameras and USB
devices should be connected to the projector directly.
• Connect a digital camera using a USB cable specified for use with the device. Since the USB cable supplied
with the 3D Glasses is exclusively for the 3D Glasses, it cannot be used for connecting a digital camera or a
USB device.
• Use a USB cable less than 3 m in length. If the cable exceeds 3 m, slideshow may not function correctly.
20
Preparing
Connecting WirelessHD devices (EH-TW6600W only)
The projector receives transmissions from the WirelessHD Transmitter, and projects the images. s p.54
Change the projected image by pressing the
control panel.
c
button on the remote control or the
button on the
• When receiving WirelessHD images, make sure WirelessHD is set to On. s Settings -
WirelessHD p.79
• You can change which device is displayed by selecting a device from Device Connections in HDMI
Link. s HDMI Link-Device Connections p.69
Connecting smartphones or tablets (EH-TW6600W only)
You can connect MHL compatible smartphones or tablets to the WirelessHD Transmitter.
Use an MHL compatible cable to connect the micro USB port of smartphones and tablets to the HDMI5 port
on the WirelessHD Transmitter.
You can operate smartphones or tablets from the projector re‐
mote control.
You can also view video and listen to music while charging a
smartphone or tablet.
Attention
• Make sure the connection cable supports the MHL standards. During charging, the smartphone or tablet
could generate heat, cause a liquid leak, explode or generate other conditions that could result in a fire.
• When a connection is made using an MHL-HDMI conversion adapter, it may not be possible to charge or
control the device from the remote control.
c
Some devices use more power during video playback than what is supplied and will therefore not
enable charging during video playback or other operations.
21
Preparing
Attaching the Wireless LAN unit
To use the wireless LAN function, attach an optional Wireless LAN unit (ELPAP07).
Insert the Wireless LAN unit to the USB port (TypeA).
To project images via a wireless LAN, you need to download the following applications. For more details, see
the download page.
• Projecting computer screens by wireless
Use EasyMP Network Projection to project computer screens via a network.
EasyMP Network Projection can be downloaded from the following Web site.
http://www.epson.com
• Projecting images from a mobile terminal via a network
When installing "Epson iProjection" in a smartphone or tablet, you can project data in the terminal by wireless. You
can enjoy the images from a smartphone or tablet easily.
"Epson iProjection" can be downloaded free of charge from App Store or Google Play. A communication fee for the
connection to App Store or Google Play will be charged to customers.
c
• When not using the wireless LAN function with the Wireless LAN unit kept inserted, set Wireless LAN
Power to Off. This can prevent unauthorized access from outsiders. s p.85
• When using Epson iProjection or EasyMP Network Projection in Quick, we recommend making security
settings. s p.86
Removing the Terminal Cover
The terminal cover is attached to the connector section on the rear of EH-TW6600W. Remove this cover when
using a cable to connect a device.
There are gaps at the bottom of the terminal cover that allows you to pull the cover forward and lift it from
the grooves at the top.
When reattaching, first insert the protruding sections into the grooves at the top.
22
Preparing
Preparing the Remote Control
Installing the Remote Control Batteries
Attention
• Check the positions of the (+) and (-) marks inside the battery holder to ensure the batteries are inserted the
correct way.
• You cannot use other batteries except for the AA size manganese or alkaline.
a
Remove the battery cover.
b
Replace the old batteries with new
batteries.
c
While pushing the battery compartment
cover catch, lift the cover up.
Reattach the battery cover.
Press the cover until it clicks into place.
c
Check the polarity of the batteries (+) and
(-) before installing.
If delays in the responsiveness of the
remote control occur or if it does not
operate, it probably means that the
batteries are becoming flat. When this
happens, replace them with new
batteries. Have two AA size manganese
or alkaline batteries ready.
Remote Control Operating Range
The operation range for the WirelessHD Transmitter differs. s p.63
Operating range (left to right)
Operating range (top to bottom)
23
Basic Operations
Starting and Ending Projection
Turning on the Projector and Projecting
a
Connect the equipment to the
projector.
b
Connect the power cord.
c
Remove the lens cap.
d
Turn on the connected equipment.
e
Turn on the projector.
Remote control
Control panel
Connect using the power cord supplied.
c
When Direct Power On is set to
On, you can start projecting by
simply connecting the power cord
to the projector without having to
press any buttons. s Settings Operation - Direct Power
On p.79
Warning
Do not look into the lens during projection.
Caution
Do not disconnect the power cord from the main
projector unit or the electrical outlet during
projection.
c
• This projector provides a Child Lock function to prevent children from accidentally turning the power
on and a Control Panel Lock function to prevent accidental operations and so on. s Settings - Lock
Setting - Child Lock/Control Panel Lock p.79
• When using at an altitude of 1500 m or more, set High Altitude Mode to On. s Settings - Operation -
High Altitude Mode p.79
• This projector provides an Auto Setup function to automatically select the optimum settings when the
input signal for the connected computer image changes. s Signal - Auto Setup p.77
• This projector comes with a Trigger Out port to communicate the current status of the projector's
power (on/off) to external devices. When using this function, set Trigger Out. s Settings - Operation -
Trigger Out p.79
• Do not attach the lens cap during projection.
• If the projector is suspended from a ceiling, after removing the lens cap, make sure you keep it in a safe
place as you will need to attach it when transporting the projector.
24
Basic Operations
If the Target Image is not Projected
If the image is not projected, you can change the source using one of the following methods.
Remote control
Press the button for the target port.
c
Control panel
Press the
Press the
button and select the target port.
button to confirm the selection.
For video equipment, start playback first and then change the source.
Turning Off
a
b
c
Turn off the connected equipment.
c
When Power Off Link is set to
On in the HDMI Link menu,
turning off HDMI CEC compatible
equipment may also turn off the
projector. s Settings - HDMI
Link - Power Off Link p.79
c
Press the
button on the remote
control or the projector's control
panel.
Remote control
Press the
button again.
When Standby Confirmation is
set to Off, you can turn off the
projector by pressing the
button on the remote control
once. s Settings - Display Standby Confirmation p.79
Control panel
A confirmation message is displayed.
25
d
Wait until cool-down is complete.
e
Disconnect the power cord.
The operation indicator on the projector's
control panel stops flashing.
c
• If the power cord is connected,
some electricity is consumed
even if no operations are made.
• When connecting the power cord
again, wait a sufficient time
interval.
Basic Operations
f
Attach the lens cap.
26
Basic Operations
Adjusting the Projected Screen
Displaying the Test Pattern
When adjusting the zoom/focus or the projection position just after setting up the projector, you can display
a test pattern instead of connecting video equipment.
Press the
button on the remote control to display the test pattern.
You can adjust the display position and so on by using this test pattern.
Press the
button to end this test pattern display.
Adjusting the Focus
Turn the focus ring to adjust the focus.
Adjusting the Projection Size (Zoom Adjustment)
Grip the knob and turn the zoom ring to adjust the size of the projected screen.
27
Basic Operations
Adjusting the Projector's Tilt
If the projection screen is tilted (the left and right sides of the projector are at different heights) when the
projector is setup on a table, adjust the front foot so that both sides are level with each other.
Adjusting the Position of the Projected Image (Lens Shift)
If the projector cannot be installed directly in front of the screen, you can adjust the position of the image by
using lens shift.
Making adjustments using the lens shift dial
Turn the vertical and horizontal lens shift dials on the projector to adjust the position of the projected image.
To locate the center of the lens shift range, turn the lens shift dial until you hear it clicks.
28
Basic Operations
Attention
• When using vertical lens shift for adjusting the position of the image, adjust the image by moving it upward
and then finish the adjustment. If you move the image downward and finish the adjustment, its position may
lower slightly.
• Do not keep turning the lens shift dials without effect. Once the projection image is positioned all the way
to one edge, turning the dial further may impair image quality.
c
• Since images are unstable immediately after the projector is turned on, before you make focus, zoom,
or lens shift settings, we recommend waiting 30 minutes or more after starting to project the images.
• The sharpest images will be achieved when both of the vertical and horizontal lens shift dials are
centered.
You can move the image using lens shift within the following range.
a Center of the lens
b Projected image with lens shift centered
Caution
Before transporting the projector, make sure to adjust the lens position to the center using the lens shift
dials. If you transport the projector when the lens is shifted up, down, left, or right, the lens shift mechanism
could be damaged. Also, attach the protective pad that was attached when you purchased it.
c
When adjusting the projection position using lens shift, you are recommended to install the projector
in parallel with the screen.
29
Basic Operations
Correcting Keystone Distortion (H/V-Keystone)
You can use the
c
buttons on the control panel to correct keystone distortion.
• You can maintain the quality of the projected image by adjusting the projection position using lens
shift. Use keystone correction when you cannot make adjustments using lens shift.
• To use keystone correction, rotate the lens shift dials to adjust the lens as shown below.
- Horizontal position of lens: Center
- Vertical position of lens: Top edge
If the lens is not positioned correctly, the projected image may be distorted.
Press the
buttons to display the V-Keystone/H-Keystone gauges.
When the gauges are displayed, press the
buttons to perform vertical correction, and press the
buttons to perform horizontal correction.
You can adjust the volume by pressing the
c are
not displayed.
p.31
buttons when the V-Keystone/H-Keystone gauges
s
When the top or bottom is too wide
When the left or right is too wide
c
• When you correct keystone distortion, the projected image may be reduced. Increase the projection
distance to fit the projected screen to the screen size.
• You can also set H/V-Keystone from the Configuration menu. s Settings - H/V-Keystone - V-
Keystone/H-Keystone p.79
• You can make effective corrections within a projection angle range of 30° in any direction.
30
Basic Operations
Adjusting the Volume
You can adjust the volume by using the
the projector's control panel.
buttons on the remote control or the
Remote control
c
buttons on
Control panel
• You can also adjust the volume from the Configuration menu. s Settings - Audio p.79
• Under normal conditions, you can adjust the volume of the projector's built-in speaker. However, by
connecting an AV system to the projector and setting HDMI Link to On and Audio Out Device to AV
System, you can adjust the AV system's volume when projecting from HDMI1, HDMI2, and
WirelessHD sources. s p.68
Caution
Do not start at high volume.
A sudden excessive volume may cause loss of hearing. Always lower the volume before powering off, so
that you can power on and then gradually increase the volume.
Hiding the Image and Muting the Audio Temporarily
You can use this to temporarily hide the image on the screen and mute the audio.
Press the
c
button to show or hide the image. The audio is also muted or played.
• For movies, because the movie continues to play even when it is hidden, you cannot return to the point
button.
at which you hid the image and muted the audio using the
• To mute or play only the audio, press the
button.
• Under normal conditions, the audio of the projector's built-in speaker will be muted or played. However,
by connecting an AV system to the projector and setting HDMI Link to On and Audio Out Device to
AV System, you can adjust the AV system's volume when projecting from HDMI1 and HDMI2.
s p.68
31
Adjusting the Image
Adjusting the Image
Selecting the Projection Quality (Color Mode)
You can obtain the optimum image quality to suit your surroundings when projecting. The brightness of the
image varies depending on the mode selected.
a
Press the
c
b
button.
You can make settings from the Configuration menu. s Image - Color Mode p.75
Select Color Mode.
Press the
buttons from the displayed menu to select Color Mode, and then press the
button to confirm the selection.
When projecting 2D images
You can select Auto, Dynamic, Living Room, Natural, and Cinema.
3D Dynamic and 3D Cinema are grayed out and cannot be selected.
When projecting 3D images
You can select 3D Dynamic and 3D Cinema.
Auto, Dynamic, Living Room, Natural, and Cinema are grayed out and cannot be selected.
Choices when projecting 2D images
Mode
Application
Auto
Sets the color mode automatically according to the surroundings. The optimum image
quality is set according to the brightness of the room detected by the sensor (auto
color adjustment function).
Dynamic
Ideal for use in a bright room.
Living Room
Ideal for use in a bright room. Images are clear and sharp.
Natural
Ideal for use in a dark room. We recommend performing color adjustment in this mode.
Cinema
Ideal for watching movies and concerts in a dark room.
32
Adjusting the Image
c
Only when Projection is Front, Auto can be set. s p.79
Choices when projecting 3D images
Mode
Application
3D Dynamic
For use when projecting 3D images. Images are bright and sharper than 3D Cinema.
3D Cinema
For use when projecting 3D images. Produces crisper colors than 3D Dynamic.
Switching the Screen Between Full and Zoom (Aspect)
You can change the input signal's type, aspect ratio, and resolution to match the Aspect of the projection
screen.
The available Aspect varies depending on the image signal currently being projected.
a
Press the
c
b
button.
Use the
buttons to
select the setting name, and then
press the
button to confirm the
selection.
You can make settings from the
Configuration menu. s Signal Aspect p.77
c
Aspect may not be available
depending on the type of signal.
By normally selecting Auto, the optimum aspect is used to display the input signal. Change the setting if you
want to use a different aspect.
The table below shows the image projected on a 16:9 screen.
Input Image
Setting Name (Aspect)
Normal
Full
Zoom
4:3 Images
16:9 Images
When projecting 16:9 images, Full and Zoom cannot be
selected.
Images Recorded Using
Squeeze
33
Adjusting the Image
Input Image
Setting Name (Aspect)
Normal
Full
Zoom
Letterbox Images*
Retains the aspect ratio of
the input signal, and
matches the horizontal
size of the projection pan‐
el. The top and bottom of
the image may be trunca‐
ted.
* The letterbox image used in this explanation is a 4:3 aspect ratio image displayed in 16:9 with black margins at
the top and bottom for subtitle placement. The margins at the top and bottom of the screen image are used for
subtitles.
Notes
c
Matches the vertical size of Uses the entire projection
the projection panel. The panel.
aspect ratio differs de‐
pending on the input im‐
age.
Note that using the aspect ratio function of the projector to reduce, enlarge, or split the projected
image for commercial purposes or for public viewing may infringe upon the rights of the copyright
holder of that image based on copyright law.
34
Adjusting the Image
Absolute Color Adjustments
Adjusting Hue, Saturation, and Brightness
You can adjust the hue, saturation, and brightness for each of the R (red), G (green), B (blue), C (cyan), M
(magenta), and Y (yellow) colors.
Hue
Adjusts the overall color of the image to be blue, green, or red.
Saturation
Adjusts the overall vividness of the image.
Brightness
Adjusts the overall color brightness of the image.
a
Press the
c
b
button.
c
Use the
buttons to
select Hue, Saturation, or
Brightness.
d
Use the
buttons to make
adjustments.
You can make settings from the
Configuration menu. s Image Advanced - RGBCMY p.75
Use the
buttons to
select the color you want to adjust,
button to
and then press the
confirm the selection.
Press the
color.
button to adjust another
button to return the
Press the
adjustments to their default values.
e
Press the
menu.
button to exit the
Adjusting the Gamma
You can adjust slight coloration differences that may occur due to the device being used when the image is
displayed.
You can use one of the following two methods selected from the Configuration menu.
Setting Method
Menu Settings
Select and adjust the correction Image - Advanced - Gamma
value
Adjust using the gamma adjust‐ Image - Advanced - Gamma - Customized - Color Tone Adjustment
ment graph
35
Adjusting the Image
Select and adjust the correction value
Select the adjustment value, and then press the
to confirm the selection.
button
The larger the value, the lighter the dark portions of the im‐
age become, but bright areas may appear discolored. The
upper part of the gamma adjustment graph becomes roun‐
ded.
The smaller the value, the darker the bright portions of the
image become. The lower part of the gamma adjustment
graph becomes rounded.
c
• The horizontal axis of the gamma adjustment graph shows the input signal level, and the vertical axis
shows the output signal level.
button to return the adjustments to their default values.
• Press the
Adjust using the gamma adjustment graph
Make the color tone adjustments while viewing the projected image.
a
b
Use the
buttons to select the
part you want to adjust from the
graph.
Use the
buttons to
adjust the brightness, and then press
the
button to confirm the
selection.
Adjusting the RGB (Offset/Gain)
For the image's brightness, you can adjust the dark areas (Offset) and the bright areas (Gain) for R (red), G
(green), and B (blue). The image becomes brighter when moved to the right (positive) and darker when moved
to the left (negative).
Offset
When the image is made brighter, shading for the darker sections is more vividly expressed.
When the image is made darker, the image appears more full-bodied but shading for the
darker sections is harder to distinguish.
Gain
When the image is made brighter, the bright sections become whiter and shading is lost.
When the image is made darker, shading for the bright sections is more vividly expressed.
The menu is displayed in the following order.
Image - Advanced - RGB
Use the
use the
buttons to select the item, and then
buttons to make the adjustments.
36
Adjusting the Image
c
Press the
button to return the adjustments to their default values.
Color Temp.
You can adjust the overall tint of the image. Make adjustments if the image is a little too blue or too red and
so on.
The menu is displayed in the following order.
Image - Color Temp.
buttons to make adjustments.
Use the
Blue tints grow stronger as the value is increased, and red
tints grow stronger as the value is reduced.
c
• The Color Temp. setting varies with the Color Mode setting.
• Press the
button to return the adjustments to their default values.
Skin Tone
You can adjust the skin tone. Make adjustments if the skin tone is too red or too green and so on.
The menu is displayed in the following order.
Image - Skin Tone
buttons to make adjustments.
Use the
The image becomes greener when set to the right (positive)
and redder when set to the left (negative).
c
Press the
button to return the adjustments to their default values.
37
Adjusting the Image
Detailed Image Adjustments
Adjusting the Sharpness
You can make the image clearer. There are two types available, Standard and Advanced which allows you
to make more detailed adjustments.
Advanced cannot be adjusted in the following situations.
• When a computer signal is being input
• When Image Processing is set to Fast in the Signal menu
• When projecting 3D images
The following shows the setting items and procedures for Advanced.
Thin Line Enhancement
Details such as hair and patterns on clothing are enhanced.
Thick Line Enhancement
Rough parts such as outlines for entire subjects or the background are enhanced,
making the overall image clearer.
Vert. Line Enhancement
Enhances the image horizontally or vertically.
Horiz. Line Enhancement
a
Press the
d
button.
Use the
buttons to
select the item, and then use the
buttons to make the adjustments.
The image is enhanced when moved to the
right (positive) and softer when moved to
the left (negative).
The Configuration menu is displayed.
b
c
Select Image - Sharpness.
The Sharpness adjustment screen is
displayed.
The upper + and - buttons adjust high and
low areas simultaneously.
Select Advanced at the top right of
the screen, and then press the
button to confirm the selection.
Press the
button to return the
adjustments to their default values.
The Advanced adjustment screen is
displayed.
e
38
Press the
menu.
button to exit the
Adjusting the Image
Setting Auto Iris
By automatically setting the luminance according to the brightness of the displayed image, it lets you enjoy
deep and rich images.
You can select the luminance adjustment tracking for changes in brightness in the displayed image from
Normal to High Speed.
(Depending on the image, you may hear the auto iris operating, but this is not a malfunction.)
a
Press the
c
button.
Use the
buttons to
select the item, and then press the
button to confirm the selection.
The Configuration menu is displayed.
b
Select Image - Auto Iris.
The Auto Iris adjustment screen is
displayed.
Super-resolution and Detail Enhancement Functions
These functions improve a resolution by making fuzzy outlines clear and emphasizing the texture and material
feel.
Super-resolution
This setting sharpens blurred images, enhancing the apparent detail of the image by
increasing the resolution of the image signal.
Depending on the image, distortion at the edge of the image may be enhanced. If you
notice any distortion, set it to "0".
Detail Enhancement
This setting enhances the contrast in an image to create the image with more emphatic
texture and material feel.
Depending on the image, a highlight may be noticeable at the border between colors.
If it worries you, set a smaller value.
c changed.
When the setting of Super-resolution is changed, the value of Detail Enhancement will also be
39
Adjusting the Image
a
Press the
c
b
button.
Use the
buttons to
select Super-resolution or Detail
Enhancement, and then use the
buttons to make the adjustments.
For Super-resolution, the higher the value,
the stronger the effect.
For Detail Enhancement, the higher the
value, the more emphatic the texture.
• You can make settings from the
Configuration menu. s Signal -
Super-resolution p.77
• This cannot be set when a
computer image signal is being
input.
• This cannot be set when
converting 2D to 3D images.
s Signal - 3D Setup - 2D-to-3D
Conversion p.77
• When projecting 3D images, this
setting is enabled only for 1080p/
24 Hz/frame packing signals.
c
Press the
button or the
button to exit the menu.
c
Set Panel Alignment to On.
Panel Alignment
Adjusts the pixel color shift of the LCD display.
a
Press the
button.
The Configuration menu is displayed.
b
Select Settings - Panel Alignment,
and then press the
button to
confirm the selection.
is enabled. When set to Off,
c value
the corrected value returns to the
When set to On, the adjusted
The Panel Alignment adjustment screen is
displayed.
default value.
40
d
In Select Color, select the color you
want to adjust.
e
In Pattern Color, select the pattern
(color combination) used for
adjustments.
Adjusting the Image
f
i
Select Start Adjustments, and then
press the
button to confirm the
selection.
First, adjust the whole LCD display. When a
message appears prompting you to start
adjustments, press the
button to start
them.
g
Adjustments are performed in four corners
starting from the top-left corner.
Use the
buttons for
adjustments, and then press the
button.
j
c
h
Use the
buttons to
adjust, and then press the
button
to move to the next adjustment point.
To restore the values before the
start of whole adjustment, press
button.
the
select Select
c adjustments,
intersection and adjust, and
To make more detailed adjustments,
select Adjust the four corners, and
then press the
button to confirm.
c
After adjusting four corners, select
button to
Exit, and then press the
confirm.
If the four corners still need
then continue adjustments.
• To finish the adjustments, select
Exit.
k
• To return to the Start
Adjustments screen, press the
button.
Press the
menu.
button to exit the
Image Processing
Improves the response speed for images projected at high-speed, such as games.
This is only available when receiving a progressive signal input from the Component, Video, HDMI1, or
HDMI2 ports, or from WirelessHD.
The
button toggles the mode between Fine and Fast.
41
Adjusting the Image
c
• You can make settings from the Configuration menu. s Signal - Advanced - Image Processing p.77
• This does not support 3D images.
• If Image Processing is set to Fast, the following settings cannot be changed:
-Noise Reduction and 2D-to-3D Conversion are fixed at Off.
-Sharpness is fixed at Standard.
-Picture in Picture cannot be used.
42
Adjusting the Image
Viewing the Image at the Saved Image Quality
(Memory Function)
Saving Function
You can save the adjustment values for some images and image quality settings in the Configuration menu
for later use (Save Memory).
Because these saved adjustment values can be loaded from the remote control, you can easily switch to your
preferred image quality (Load Memory).
The following Configuration menu functions can be saved.
Image
s p.75
Color Mode, Brightness, Contrast, Color Saturation, Tint, Skin Tone, Sharpness, Color Temp..,
Power Consumption, Auto Iris
Advanced
Signal
s p.77
Gamma, Offset, Gain, Hue, Saturation, Brightness, EPSON Super White
Deinterlacing, Motion Detection, Super-resolution
Advanced
Noise Reduction, Setup Level, Overscan, HDMI Video Range
Saving a Memory
You can register a memory when Color Mode is set to anything except Auto.
a
Make settings that you want to save to
the Configuration menu.
b
Press the
c
Use the
buttons to
select Save Memory, and then press
the
button to confirm the
selection.
d
button.
Use the
buttons to
select the memory name to be saved,
button to
and then press the
confirm the selection.
The current projector settings are saved to
the memory.
If the mark on the left of the memory name
is turned aqua, it means the memory has
already been registered. When you select a
registered memory, a message is displayed
asking you to confirm that you want to
overwrite the memory. If you select Yes, the
previous content is erased and the current
settings are saved.
The Save Memory screen is displayed.
43
Adjusting the Image
Loading a Memory
a
Press the
b
Select the target memory name.
button, and then select Load Memory.
The Load Memory screen is displayed.
c
• The color mode saved to the memory is displayed on the right.
• Depending on the input signal, part of the loaded memory item may not be applied to the
projected image.
• Memories saved for 2D images can only be loaded when projecting 2D images. Memories saved
for 3D images can only be loaded when projecting 3D images.
Deleting a Saved Memory
a
Press the
b
Select the target memory name.
button, and then select Erase Memory.
The Erase Memory screen is displayed.
A confirmation message is displayed. If you select Yes, the content of the saved memory is erased.
c
If you want to erase all of the saved memories, go to Reset - Reset Memory on the
Configuration menu. s p.87
Renaming a Memory
You can rename each memory name using up to 12 characters. Giving the memory a name that is easy to
remember is useful when loading the memory.
a
Press the
b
Select the target memory name.
c
Select a displayed name or Customized.
button, and then select Rename Memory.
The Rename Memory screen is displayed.
The name list screen is displayed.
To enter a name of your own, select Customized, and then go to step 4. If you select Customized, a
keyboard is displayed.
If you select from the name list, check that the memory name has been changed.
44
Adjusting the Image
d
Enter a name.
Use the
buttons to select a
button to con‐
character, and then press the
firm the selection. Enter up to 12 characters.
When you have finished entering the name, se‐
lect Finish.
The memory name is changed.
45
Useful Functions
Enjoying 3D Images
Setting 3D Images
Set the source to HDMI1, HDMI2, or WirelessHD (EH-TW6600W only) to view 3D images.
The projector supports following 3D formats.
• Frame Packing
• Side by Side
• Top and Bottom
When the projector detects a 3D format
The projector automatically projects a 3D image when detecting a 3D format.
When the projector cannot detect a 3D format
Some 3D TV broadcasts may not contain 3D format signals. If this
happens, set the 3D format manually. Press the
button to
set the 3D format on the AV device.
c
• When viewing 3D images with an AV amplifier connected, use a 3D compatible AV amplifier.
• For details on 3D format settings on the AV device, see the documentation supplied with the AV device.
• When the 3D format has not been correctly set up, an image will not be correctly projected as shown
below.
If the 3D image cannot be viewed
Check the following if the 3D effect is not displayed correctly, even after setting the 3D formats.
• The synchronization timing for the 3D Glasses may have been inversed. Inverse the synchronization using Inverse
3D Glasses, and then try again. s Signal - 3D Setup - Inverse 3D Glasses p.77
• The image is not displayed in 3D if 3D Display is set to Off. Press the
button on the remote control. s Signal 3D Setup - 3D Display p.77
c
• How a 3D image is perceived varies depending on the individual.
• When a 3D image is displayed, a warning about viewing 3D images is displayed. You can turn off this
warning by setting 3D Viewing Notice to Off. s Signal - 3D Setup - 3D Viewing Notice p.77
• You can also convert 2D images to 3D images. s p.52
• During 3D projection, the following Configuration menu functions cannot be changed.
Aspect (set to Normal), Noise Reduction (set to Off), Overscan (set to Off), Super-resolution, Image
Processing, Advanced - Sharpness, Picture in Picture
• How the 3D image is viewed may change depending on the temperature of the surroundings and how
long the lamp has been used. Refrain from using the projector if the image is not projected normally.
46
Useful Functions
Using 3D Glasses
Use the supplied or optional 3D Glasses (ELPGS03) to view 3D images.
Depending on the model, 3D Glasses may not be supplied.
c
The 3D Glasses come with protective stickers. Remove the protective stickers before use.
Charging the 3D Glasses
The following charging methods are available, depending on the model of 3D Glasses being used.
If you have a WirelessHD Transmitter, you can use it to charge the glasses.
If you do not have a WirelessHD Transmitter, you can charge by using an optional USB Charging Adapter.
You can also charge by connecting the 3D Glasses to the USB port (TypeA) on the rear of the projector with
the USB cable (only when the projector is turned on).
connect the USB Charging Adapter to an electrical
outlet.
Charging using the WirelessHD Transmitter
Use the USB cable to connect the 3D Glasses to
the WirelessHD Transmitter.
c
When a cable is connected to the HDMI5 port, the
WirelessHD Transmitter cannot charge 3D
glasses.
The approximate charging and usage
times are as follows:
Charging
time
Charging using the USB Charging Adapter
Use the USB cable to connect the 3D Glasses to
the optional USB Charging Adapter, and then
Usage time
3 minutes
Approx. 3 hours
50 minutes
Approx. 40 hours
Attention
• Only connect to an electrical outlet that uses the voltage displayed on the 3D Glasses.
• Note the following points when handling the supplied microUSB cable.
- You should not bend, twist, or pull the cable with too much force.
- You should not modify the cable.
- You should not perform wiring near an electric heater.
- You should not use the cable if it is damaged.
Pairing 3D Glasses
To create 3D images, the 3D Glasses need to be paired with the projector.
47
Useful Functions
Press the [Pairing] button for a while on the 3D Glasses to start pairing.
a
b
Turn on the 3D Glasses by sliding the
[Power] switch to On.
The indicator turns on for several seconds,
and then turns off.
c
Press and hold the button for three
seconds.
The indictor flashes green and red in turn.
If pairing has been performed correctly, the
indicator turns on for ten seconds and then
turns off.
• For 3D Glasses that have not been used, pairing is performed when the 3D Glasses are turned on. You
do not need to perform pairing if 3D images can already be viewed correctly.
• Once pairing has been performed, you can view 3D images the next time the devices are turned on.
• You can perform pairing within a range of three meters from the projector. While pairing is being
performed, make sure you stay within a range of three meters from the projector. Otherwise, pairing
will fail.
• If synchronization cannot be performed within 30 seconds, pairing is automatically canceled. When
pairing is cancelled, 3D images cannot be viewed because pairing fails.
Wearing the 3D Glasses
a
b
Turn on the 3D Glasses by sliding the
[Power] switch to On.
The indicator turns on for several seconds,
and then turns off.
Put on the 3D Glasses and enjoy the
show.
c
48
• When you have finished using the
3D Glasses, turn them off by
sliding the [Power] switch to Off.
• If the 3D Glasses are not used for
at least 30 seconds, they turn off
automatically. To turn the 3D
Glasses back on, slide the
[Power] switch to Off, and then
slide it back to On.
• You need more pairs of optional
3D Glasses if more than one
person will be viewing the 3D
image. s p.109
Useful Functions
Reading the indicator on the 3D Glasses
You can check the status of the 3D Glasses by whether its indicator is lit or flashing.
Indicators
Status
Flashes red two times ×5
Weak battery
Lit red
Charging
Lit green
Charging completed
Flashes green and red in turn
Pairing
Lit green for ten seconds and then turns Power on or pairing succeeded
off
Range for Viewing 3D Images
This projector allows you to view 3D images within the range shown in the figure below.
You can view 3D images within a range of 10 meters from the projector.
c
• 3D images may not be displayed correctly if there is any interference from other Bluetooth
communication devices. Do not use these devices at the same time.
• The communication method for 3D Glasses uses the same frequency (2.4 GHz) as wireless LAN
(IEEE802.11b/g) or microwave ovens. Therefore, if these devices are used at the same time, radio wave
interference may occur, the image may be interrupted, or communication may not be possible. If you
do need to use these devices at the same time, make sure there is enough distance between them and
the projector.
• The 3D Glasses for this projector are Bluetooth active shutter 3D glasses.
49
Useful Functions
Warnings Regarding Viewing 3D Images
Note the following important points when viewing 3D images.
Warning
Disassembling or remodeling
• Do not disassemble or remodel the 3D Glasses.
This could cause a fire to occur or the images to appear abnormal when viewing, causing you to feel unwell.
Storage locations
• Do not leave the 3D Glasses or the supplied parts within reach of children.
They could be accidentally swallowed. If anything is accidentally swallowed, contact a doctor immediately.
Wireless (Bluetooth) communication
• Electromagnetic interference may cause medical equipment to malfunction. Before using the device, make
sure there is no medical equipment in the vicinity.
• Electromagnetic interference may cause automatically controlled equipment to malfunction which could
cause an accident. Do not use the device near automatically controlled equipment such as automatic doors
or fire alarms.
Heating
• Do not place the 3D Glasses in a fire, on a heat source, or leave them unattended in a location subject to high
temperatures. Because this device has a built-in rechargeable lithium battery, it could cause burns or a fire if
it ignites or explodes.
Charging
• When charging, connect the supplied cable to the USB port designated by Epson. Charging should be
performed either via WirelessHD, this projector, or the genuine adapter. Do not charge using other devices
as it may cause the battery to leak, overheat, or explode.
• Only use the supplied charging cable to charge the 3D Glasses. Otherwise, it could overheat, ignite, or explode.
Caution
3D Glasses
• Do not drop or press too forcefully on the 3D Glasses.
If the glass sections and so on are broken, an injury could occur. Store the glasses in the soft glasses case.
• Be careful of the edges of the frame when wearing the 3D Glasses.
If it pokes your eye and so on, an injury could occur.
• Do not place your finger in any of the moving sections (such as the hinges) of the 3D Glasses.
Otherwise an injury could occur.
50
Useful Functions
Caution
Wearing 3D Glasses
• Make sure you wear the 3D Glasses correctly.
•
•
•
•
•
Do not wear the 3D Glasses upside down.
If the image is not displayed correctly into the right and left eyes, it could cause you to feel unwell.
Do not wear the glasses unless you are viewing a 3D image.
How a 3D image is perceived varies depending on the individual. Stop using the 3D function if you feel strange
or cannot see in 3D.
Continuing to view the 3D images could cause you to feel unwell.
Stop wearing the 3D Glasses immediately if they seem abnormal or a malfunction occurs.
Continuing to wear the 3D Glasses could cause an injury or cause you to feel unwell.
Stop wearing the 3D Glasses if your ears, nose, or temples become red, painful, or itchy.
Continuing to wear the 3D Glasses could cause you to feel unwell.
Stop wearing the 3D Glasses if your skin feels unusual when wearing the glasses.
In some very rare cases the paint or materials used in the 3D Glasses could cause an allergic reaction.
Caution
Viewing Time
• When viewing 3D images, always take periodic breaks during extended viewing.
Long periods of viewing 3D images may cause eye fatigue.
The amount of time and frequency of such breaks varies from person to person. If your eyes still feel tired or
uncomfortable even after taking a break from viewing, stop viewing immediately.
Caution
Watching 3D Images
• If your eyes feel fatigued or uncomfortable when viewing 3D images, stop viewing immediately.
Continuing to view the 3D images could cause you to feel unwell.
• When viewing 3D images, be sure to always wear 3D Glasses. Do not attempt to view 3D images without 3D
•
•
•
•
•
Glasses.
Doing so could cause you to feel unwell.
Do not place any breakable or fragile objects around you when using 3D Glasses.
3D images may cause you to move your body involuntarily, resulting in damage to nearby items or personal
injury.
Only wear 3D Glasses when viewing 3D images. Do not move around while wearing 3D Glasses.
Your vision may appear darker than normal, causing you to fall or injure yourself.
Try to stay as level with the viewing screen as possible when viewing 3D images.
Viewing 3D images at an angle reduces the 3D effect and may cause you to feel unwell due to unintended
color changes.
If using 3D Glasses in a room with fluorescent or LED lighting, you may see flashing or flickering throughout
the room. If this should occur, reduce the lighting until the flickering goes away or turn off the lights completely
when viewing 3D images. In some very rare cases, this flickering could trigger seizures or fainting for some
individuals. If you begin to feel uncomfortable or unwell at any time when viewing 3D images, stop
immediately.
Stay at least three times the height of the screen away from the screen when viewing 3D images.
The recommended viewing distance for an 80-inch screen is at least 3 meters, and at least 3.6 meters for a
100-inch screen.
Sitting or standing any closer than the recommended viewing distance may result in eye fatigue.
51
Useful Functions
Caution
Health Risks
• You should not use 3D Glasses if you are sensitive to light, have a heart condition, or are unwell.
Doing so could aggravate your pre-existing conditions.
Caution
Recommended Age of Use
• The minimum recommended age to view 3D images is six years old.
• Children under the age of six are still developing and viewing 3D images may cause complications. Consult
your doctor if you have any concerns.
• Children viewing 3D images through 3D Glasses should always be accompanied by an adult. It is often difficult
to tell when a child is feeling tired or uncomfortable, which could result in them feeling suddenly unwell.
Always check with your child to ensure that they are not experiencing any eye fatigue during viewing.
Converting 2D Images to 3D and Viewing
You can convert 2D images from HDMI1, HDMI2, or WirelessHD (EH-TW6600W only).
a
Press the
button.
d
Select the strength of the 3D effect,
and then press the
button to
confirm the selection.
e
Press the
button to turn 3D
Display to On.
The Configuration menu is displayed.
b
Select Signal - 3D Setup, and then
button to confirm the
press the
selection.
The 3D Setup screen is displayed.
c
The
button toggles 3D Display
between On and Off.
Select 2D-to-3D Conversion, and
then press the
button to confirm
the selection.
52
Useful Functions
c
• When using 2D-to-3D Conversion, set 3D Format to Auto or 2D. s Signal - 3D Setup - 3D
Format p.77
• If Image Processing is set to Fast, you cannot adjust 2D-to-3D Conversion. s Signal - Advanced -
Image Processing p.77
53
Useful Functions
Connecting with WirelessHD (EH-TW6600W
Only)
Installing the WirelessHD Transmitter
You can use the supplied WirelessHD Transmitter to wirelessly receive image and sound data.
This is useful when the projector cannot be setup near your AV devices as you can connect the devices to the
projector without using cables.
You can use the WirelessHD Transmitter in the following ways.
• You can connect up to five AV devices at the same time, and switch images using the remote control.
• As well as the projector, you can connect another monitor device, such as a television, to the Output port, and then
switch the output using the remote control.
• This allows other monitor devices connected to the Output port to project images from the connected AV device,
even if the projector is off.
• You can connect smart devices and tablets that support MHL, and then project images from the connected MHL
device. You can also operate MHL devices from the projector's remote control, as well as charge the MHL device.
WirelessHD Transmitter part names
Front
Rear
54
Useful Functions
Name
Function
a t button
Turns the transmitter on or off.
button for WiHD Transmit‐
This performs the same function as the
ter control on the lower section of the remote control.
b Input button
Changes to the image from each input port.
button for WiHD Transmit‐
This performs the same function as the
ter control on the lower section of the remote control.
c Output button
Switches the output image to the Wireless or Output port.
button for WiHD Transmit‐
This performs the same function as the
ter control on the lower section of the remote control.
d Main power switch
e AC adapter port
Turns the main power for the transmitter on or off.
f Optical Audio-Out port
g HDMI Output port
Connects to audio devices equipped with an optical digital audio input port.
h HDMI Input port
Connects to the AV device you want to playback. You can switch the input
image using the Input button.
Connects the AC adapter.
Connects to monitor devices, such as televisions. You can switch the output
using the Outputbutton.
The HDMI5 port of the unit meets the MHL standards. You can play content
from MHL compatible smart devices or tablets connected with an MHL ca‐
ble.
i 3D Glasses charging port
j Setup button
Connects a USB cable to charge the 3D Glasses.
k t indicator
(orange/green)
Lit when the WirelessHD Transmitter is on. Lit orange when standing by,
and green when operating (receiving or transmitting images).
l WiHD indicator
(orange)
Indicates the communication status for the WirelessHD.
m Link indicator
(orange)
Indicates the connection status with the projector.
c
This is the button on the back of the WirelessHD Transmitter. It is used for
setting the WirelessHD Transmitter.
• Lit when wirelessly transmitting images to the projector.
• Off when outputting to the Output port.
• Turns on when connected to the projector.
• Flashes when searching for a projector.
• Flashes slowly when standing by in power saving status.
• The receiver is located within the intake vent of the projector and therefore cannot receive any signals
directly from the rear. Set up so that the front of the projector is facing the WirelessHD Transmitter.
Also, make sure that the air intake vent on the left-hand side of the projector is not covered.
• Place the WirelessHD Transmitter on a level surface facing towards the projector.
• You can view the signal strength from the WirelessHD settings menu. s Settings - WirelessHD Video Reception p.79
55
Useful Functions
WirelessHD Transmitter connection example and signal flow
Connection example 1: Viewing without an AV amplifier
Connect a device to WirelessHD Transmitter without using an AV amplifier, and connect the sound bars and
so on to the Optical Audio-Out port to output audio.
When outputting audio from a connected device, you need an optical digital audio cable.
* When connecting a device, such as a sound bar, to the Optical Audio-Out port on the WirelessHD Transmit‐
ter, check that Audio Out Device is set to WirelessHD Transmitter. s Settings - HDMI Link - Audio Out
Device p.79
56
Useful Functions
Connection example 2: Viewing with a connected AV amplifier
The audio from the device connected to the AV amplifier is output from the amplifier's audio-out port without
passing through the WirelessHD Transmitter.
When outputting audio from a device connected with an MHL cable, you need an optical digital audio cable.
AMP
* When connecting an MHL compatible smart device to the HDMI5 port with an MHL cable, you must connect
the AV amplifier to the Optical Audio-Out port on the WirelessHD Transmitter in order to output the audio.
Also make sure that Audio Out Device is set to AV System. s Settings - HDMI Link - Audio Out Device p.79
The audio output method to an AV amplifier may be restricted by the specifications of the monitor device,
such as a television, connected to the Output port. For more information on audio output settings, see the
documentation supplied with the AV device.
57
Useful Functions
Setting the WirelessHD Transmitter
a
c
b
c
Set up the WirelessHD Transmitter
connected to the projector so that
they are facing each other. s p.61
Using an HDMI cable, connect the AV
device you want to use to the Input
port on the WirelessHD Transmitter.
You can connect up to five multi-media
players.
• The receiver is located at the front
of the projector and therefore
cannot receive any signals
directly from the rear. Set up so
that the front of the projector is
facing the WirelessHD
Transmitter.
Also, make sure that the receiver
is not covered.
• Place the WirelessHD
Transmitter on a level surface
facing towards the projector.
Connect the WirelessHD Transmitter
to an electrical outlet using the
supplied AC adapter.
c
• You can connect another monitor device, such as a television, to the Output port on the WirelessHD
Transmitter. You can switch between output images using the remote control. s p.63
• The HDMI5 port of the WirelessHD Transmitter supports the MHL input signal. You can play content
from MHL compatible smart devices or tablets connected with an MHL cable.
• If the following message is displayed when you connect an MHL device, the device has been connected
to a port other than the HDMI5 port, or the connected device is not compatible with MHL.
"No Signal"
• You can use the HDMI link function even when using the WirelessHD Transmitter. s p.68
58
Useful Functions
Projecting Images
a
Start playback on the AV device, and then turn on the projector and the WirelessHD
Transmitter.
The t indicator on the WirelessHD Transmitter turns on.
b
Check the status of the WiHD indicator on the WirelessHD Transmitter.
If the WiHD indicator is on, go to the next step.
If the indicator is off, press the
button on the remote control or the WirelessHD Transmitter.
Make sure you point the remote control at the WirelessHD Transmitter when using the
on the remote control.
Remote control
c
button
WirelessHD Transmit‐
ter
Check the status of the Link indicator on the WirelessHD Transmitter.
If the WirelessHD Transmitter is connected to the projector, the Link indicator flashes and then remains
on.
c
• If the indicator continues to flash slowly, the WirelessHD Transmitter cannot connect to the
projector and has entered standby status. Make sure the projector has been setup correctly,
such as turning on the power and so on.
• You can view the signal strength while images are being projected from the WirelessHD settings
menu. s Settings - WirelessHD - Video Reception p.79
59
Useful Functions
d
If projection does not start, press the
source.
button on the remote control to change the
Make sure you point the remote control at the projector when using the
control.
button on the remote
Projection starts.
e
When connecting two or more AV devices to the WirelessHD Transmitter, press the
button to switch images. s p.65
c
• When receiving WirelessHD images, make sure WirelessHD is set to On from the Configuration menu.
s Settings - WirelessHD - WirelessHD p.79
• Make sure you turn off the WirelessHD Transmitter if it is not going to be used for an extended period.
WirelessHD Settings Menu
a
Press the
b
Select Settings - WirelessHD, and
then press the
button to confirm
the selection.
c
button.
The Configuration menu is displayed.
Make settings for each of the
displayed functions.
The WirelessHD settings screen is
displayed.
Available functions on the WirelessHD settings menu
Function
Explanation
Device Connections
Displays a list of available WirelessHD devices that can be connected. The device names
and MAC addresses (device numbers) are displayed in the list. The MAC address is
displayed on the label on the base.
WirelessHD
Enables or disables the WirelessHD function.
Video Reception
Displays the reception for the image being projected.
WiHD Mode
Use Full for most situations. Full mode uses the maximum video bandwidth at all times.
Dynamic mode extends wireless ranges while optimally adjusting video bandwidth.
Set to Dynamic if the image is interrupted due to weak signals and other causes.
60
Useful Functions
Function
Reset
Explanation
Resets WirelessHD settings to their default settings.
Reception when no image signal is being input. Check the communication status using the
c Video
Link indicator.
p.54
Even when the WirelessHD Transmitter and the projector are connected, 0% is displayed as the
s
WirelessHD Transmission Range
The following shows the WirelessHD transmission range. Make sure you set up the WirelessHD Transmitter
so that it faces the projector.
Horizontal direction (when WiHD Mode is set to Full)
Horizontal direction (when WiHD Mode is set to Dy‐
namic)
Vertical direction (suspended from a ceiling)
Vertical direction (suspended from a ceiling)
Vertical direction (placed on a table and so on)
Vertical direction (placed on a table and so on)
61
Useful Functions
c
• The wireless transmission range varies depending on the placement and material of the surrounding
furniture and walls. The values given here are for your reference only.
• The projector cannot communicate through walls.
• The antennas are built-into the front of the projector and the WirelessHD Transmitter. Make sure the
antennas face each other (face the front) when setting up the devices.
• Do not place any object over the front side of the projector and WirelessHD Transmitter. Doing so may
interfere with the image or prevent it from being displayed. Install so that the signal from the front of
the transmitter is not interrupted.
• Do not install the transmitter on a metal shelf. The metal may make the signal unstable. Install on a
shelf made from wood etc.
• When checking operations, place the projector and the WirelessHD Transmitter close to each other,
and make sure there are no other projectors operating in the vicinity.
• Depending on the reception strength, the image's color information may be automatically discarded
to avoid any interruptions and maintain a constant connection. To avoid any deterioration in image
quality, adjust the position of the WirelessHD Transmitter so that the Video Reception is as strong as
possible.
Operating the Remote Control
Name
Function
a
Turns the power for the WirelessHD Transmitter on or off.
b
Switches the image source for the AV device connected to the WirelessHD Transmitter.
s p.65
c
Switches the output image between a monitor device, such as a television, connected to
the Output port on the WirelessHD Transmitter and the projector. s p.63
d
Allows you to simultaneously project two image sources, one in the main screen and the
other in the sub screen. (Picture in Picture) s p.67
c
Point the remote control towards the WirelessHD Transmitter.
62
Useful Functions
Remote Control Operating Range
The following shows the operating range between the remote control and the WirelessHD Transmitter.
Operating range (left to right)
Operating range (top to bottom)
Switching the Input and Output
With the WirelessHD Transmitter, you can connect and switch between up to five multi-media players (input
devices to be played back) and one monitor device (a monitor device displaying an image, such as a television).
Point the remote control at the WirelessHD Transmitter and press its
devices and its
button to switch between output devices.
button to switch between input
Switching the target image
You can switch between a monitor device, such as a television, connected to the Output port on the
WirelessHD Transmitter and the projector.
63
Useful Functions
a
Turn on the projector or the monitor device, such as a television.
b
Turn on the WirelessHD Transmitter.
c
Point the remote control at the WirelessHD Transmitter, and then press the
The t indicator on the WirelessHD Transmitter turns on.
Remote control
button.
WirelessHD Transmit‐
ter
Depending on the output target, the WiHD indicator on the WirelessHD Transmitter indicates the
following status. The output target projected last time is projected the next time the projector is turned
on.
On: The image is being output to the projector.
Off: The image is being output to the monitor device.
c
You can switch to the other monitor device even when the projector is off.
64
Useful Functions
Switching the image source
You can switch the image source for the AV device connected to the WirelessHD Transmitter. When switching,
each input source is displayed on one screen as a preview. This allows you to switch easily between image
sources even when two or more devices are connected using HDMI.
The projector uses Insta Prevue Technology from Silicon Image, Inc.
65
Useful Functions
a
Point the remote control at the
WirelessHD Transmitter, and then
press the
button.
Remote control
b
The target screen changes each time
you press the
button.
c
After selecting the target screen,
please wait for a moment.
WirelessHD Trans‐
mitter
Displays the sub-screen (small screen) for
the connected device.
Ex.) When projecting images for the device
connected to the HDMI2 port
The projected image is switched.
c signal is displayed in blue or black.
The screen that is not receiving an image
Ex.) When images for the device
connected to the HDMI2 port are not
displayed
The connected AV device is not turned
on, or the cables are not connected
correctly. Check that the AV device is
turned on, or all the cables required for
projection are securely connected.
66
Useful Functions
Displaying as a Sub-Screen
a
c
Point the remote control at the
WirelessHD Transmitter, and then
press the
button.
To close the sub-screen, press the
button again.
The projected image is switched.
c
Displays the sub-screen (small screen) for
the connected device.
b
When switching between the subscreen and the main screen (large
screen), press and hold down the
button (for 3 seconds) until the
screen changes.
67
• When the sub-screen is displayed, press
button to switch the image
the
for the sub-screen.
• When the sub-screen is displayed, press
button to change the
the
position and size (large or small) of the
sub-screen. Each time the
button is pressed, the display position
moves from bottom right, top right, top
left, and bottom left allowing you to
change the size.
Useful Functions
Using the HDMI Link Function
HDMI Link Function
When an AV device that meets the HDMI CEC standards is connected to the projector's HDMI port, you can
perform linked operations such as linked power on and volume adjustment for the AV system from one
remote control. Also, when projecting images in WirelessHD, you can use the HDMI link function (EHTW6600W only).
c
• As long as the AV device meets the HDMI CEC standards, you can use the HDMI link function even if
the AV system in-between does not meet the HDMI CEC standards.
• Up to 3 multi-media players that meet the HDMI CEC standards can be connected at the same time.
Connection Example
Projector
Amplifier
Multi-media players and so on
HDMI Link Settings
By pressing the
button on the remote control, and
setting HDMI Link to On, you can operate the following
functions.
Function
Explanation
Power On Link
Powers on the projector when content is played back on the connected device. Or,
powers on the connected device when the projector is turned on.
Power Off Link
Powers off the connected device when the projector is turned off.
• This only works when the connected device's CEC power link function is enabled.
• Note that depending on the status of the connected device (for example, if it is record‐
ing), the device may not power off.
Audio Out Device
Selects which device outputs audio.
Projector: Outputs audio from the projector’s built-in speakers.
AV System: Outputs audio from the HDMI CEC compatible AV amplifier connected to
the HDMI port.
WirelessHD Transmitter*: Outputs audio from speakers, such as a sound bar, con‐
nected to the Optical Audio-Out port on the WirelessHD Transmitter.
Input Change Link
Changes the input source of the projector to HDMI when content is played back on the
connected device.
Connected Devices
You can perform operations such as Play, Stop, Fast Forward, Rewind, Next Chapter,
Operations
Previous Chapter, and Pause from the remote control for the projector.
* Only EH-TW6600W is displayed.
68
Useful Functions
c
• To use the HDMI Link function, you must configure the connected device. See the documentation
supplied with the connected device for more information.
• Even when using the WirelessHD Transmitter with Power On Link set to Device -> PJ or
Bidirectional, if WirelessHD is set to On, this projector also turns on when the AV device connected
to the WirelessHD Transmitter is turned on (EH-TW6600W only). s Settings-HDMI Link-Power On
Link p.79
Device Connections
You can check the connected devices that are available for HDMI Link, and select on the device you want to
project the image from. Devices that can be controlled by HDMI link automatically become the selected
device.
a
b
Press the
button, and then select
Device Connections.
Select the device you want to operate
using the HDMI Link function.
The Device Connections list is displayed.
Devices that have an aqua icon to their left
are linked.
If the device name cannot be determined
this field is left blank.
c
• Only one AV amplifier is recognized. If multiple amplifiers are connected, the amplifier recognized first
is displayed.
• If the cable does not meet the HDMI standards, operations are not possible.
• Some connected devices or functions of those devices may not operate properly even if they meet the
HDMI CEC standards. See the documentation and so on supplied with the connected device for more
information.
69
Useful Functions
Playing Back Image Data (Slideshow)
Compatible Data
The following types of files stored on USB storage devices such as USB memories, digital cameras, and so on
that are connected to the projector's USB port (TypeA) can be displayed as a slideshow.
Slideshow compatible file types
File Type (Extension)
Notes
•
•
•
•
.jpg
Images using CMYK color mode are not compatible.
Progressive format images are not compatible.
Images with a resolution greater than 8192 x 8192 are not compatible.
Due to the characteristics of JPEG files, images may not be projected clearly if the
compression ratio is too high.
Attention
Connect a digital camera using a USB cable specified for use with the device. Do not use the USB cable
supplied with your 3D Glasses.
Playing a Slideshow
a
Connect a USB storage device.
Files are displayed as thumbnails.
To open a folder, select the folder, and then press the
c change the source.
button.
If thumbnails of the files are not displayed, press the
b
button on the remote control to
Select Slideshow.
Use the
press the
buttons to select Slideshow at the bottom right of the screen, and then
button.
Slideshow starts.
70
Useful Functions
c
• To close the Slideshow, disconnect the USB storage device.
• Select an image from the thumbnails and press the
button to enlarge the selected image.
buttons on the remote control when viewing an enlarged image to change between
Press the
images. You can also rotate the image using the
buttons.
Display Settings for Image Files and Slideshow Operation Settings
You can set the file display order and slideshow operations on the option screen.
a
Use the
buttons to position the cursor over the folder where you want
button. Select Option from the submenu
to set display conditions, and then press the
displayed, and then press the
button.
b
When the option screen is displayed, set each of the items.
c
Enable settings by positioning the cursor on the target item and pressing the
The following table shows the details for each item.
button.
Display Order
You can select to display the files in Name Order or Date Order.
Sort Order
You can select to sort the files In Ascending or In Descending order.
Continuous Play
You can set whether to repeat the play.
Screen Switching
Time
When playing a slideshow, you can set the time for a single file to be dis‐
played. You can set a time between Off (0) to 60 seconds. When you set
Off, auto play is disabled.
Effect
You can set the screen effects when changing slides.
When you have finished making settings, use the
button.
the cursor over OK, and then press the
buttons to position
The settings are applied.
If you do not want to apply the settings, position the cursor on Cancel, and then press the
71
button.
Useful Functions
Projecting Two Different Images Using Picture
in Picture
Types of Screen that can be Displayed Simultaneously
Two different image sources can be projected, one in the main
screen (large screen) and the other in the sub screen (small screen).
You can view the sub screen while viewing the main screen.
Combinations of input sources for Picture in Picture projection
HDMI1
HDMI2
WirelessHD*
HDMI1
-
-
-
HDMI2
-
-
-
WirelessHD*
-
-
-
Component
Video
PC
Component
-
-
-
Video
-
-
-
PC
-
-
-
* EH-TW6600W only
Projecting on a Picture in Picture
Starting and exiting Picture in Picture
Press the
button on the remote control while the projector is projecting.
The currently input image is displayed on a Picture in Picture.
Main screen: The current image
Sub screen: The source different from the main screen
Press the
c
•
•
•
•
button again to end the Picture in Picture display.
You cannot use Picture in Picture display to project 3D images.
You can change the displays between the main and the sub screen by holding down the
button.
If the source being input is not supported, nothing is displayed.
The Picture in Picture function cannot be used when Image Processing is set to Fast in the Signal
menu. s Signal-Advanced -Image Processing p.77
72
Useful Functions
Changing the Picture in Picture settings
Use the Picture in Picture menu to change the size or position of the sub screen.
a
Press the
c
b
button.
Make settings for each of the
displayed functions.
The Picture in Picture menu is
displayed directly by pressing the
button during Picture in
Picture projection.
Available functions on the Picture in Picture menu
Function
Explanation
Subscreen Size
Selects the sub screen size using Small and Large.
Subscreen Position
Changes the sub screen position using Top Right, Bottom Right, Top Left, and Bot‐
tom Left.
Subscreen Source
Selects which source is displayed in the sub screen.
Swap Main/Sub
Changes the main and sub screens.
Exit Picture in Picture
Exits the Picture in Picture display.
73
Configuration Menu
Configuration Menu Functions
Configuration Menu Operations
On the Configuration menu, you can make adjustments and settings for Signal, Image, and so on.
a
Press the
c
button.
Remote control
Control panel
Use the
buttons to
select the sub menu on the right, and
then press the
button to confirm
the selection.
The Configuration menu is displayed.
b
Use the
buttons to
select the top menu on the left, and
button to confirm
then press the
the selection.
The adjustment screen for the selected
function is displayed.
When you select the top menu on the left,
the sub menu on the right changes.
d
Use the
adjust the settings.
buttons to
Ex.) Adjustment bar
Ex.) Choices
The line at the bottom is a guide for
operations.
Press the
button on an item displaying
icon to change to the selection
this
screen for that item.
Press the
button to return to the
previous level.
e
74
Press the
menu.
button to exit the
Configuration Menu
c
For items adjusted using an adjustment bar, such as the brightness level, you can press the
button while the adjustment screen is displayed to return the adjustment value to its default value.
Configuration Menu Table
If there is no image signal being input, you cannot adjust items related to the image or signal in the
Configuration menu. Note that the items displayed for the image, the signal, and other information vary
depending on the image signal being projected.
Image menu
Function
Color Mode
Menu/Settings
Explanation
Auto, Dynamic, Living Room, Natural, Cinema,
3D Dynamic, 3D Cinema
Select the image quality based on your
surroundings and the image you are pro‐
jecting. s p.32
Brightness*1
Adjusts the image brightness.
Contrast*1
Adjusts the contrast between light and
shade in the images. By increasing the
contrast, the images become vivid.
Color Satura‐
tion*1*2
Adjusts the color saturation for the im‐
ages.
Tint*1*2
Adjusts the tint for the images.
Skin Tone*1
Adjusts the skin tone. The image becomes
greener when set to a positive value and
redder when set to a negative value.
Sharpness
Standard
Advanced*2
Color Temp.
Adjusts the image sharpness.
Thin Line Enhance‐
ment, Thick Line En‐
hancement, Vert. Line
Enhancement, Horiz.
Line Enhancement
Adjusts the image sharpness.
Use this to adjust specific areas. s p.38
-3 to 6 (10 increments)*3
Adjusts the tint for the images. The image
is tinted blue for high values, and tinted
red for low values.
75
Configuration Menu
Function
Advanced
Menu/Settings
Gamma
Explanation
2, 1, 0, -1, -2
Customized*4 Display Confirmation
Graph/Guide, Color
Tone Adjustment
Performs gamma adjustments. You can
select a raw value or adjust the gamma
while looking at the graph. s p.35
Reset
RGB
Adjusts the offset and gain for each R, G,
and B color. s p.36
Offset R/G/B
Gain R/G/B
RGBCMY
R/G/B/C/M/Y
EPSON Super White
Hue, Satura‐
tion, Bright‐
ness
Adjusts the hue, saturation, and bright‐
ness for each R, G, B, C, M, and Y color.
s p.35
On, Off
(This can only be set when the Color
Mode is set to Natural, Cinema, or 3D
Cinema and when receiving signal input
from the HDMI1 or HDMI2 ports, or from
WirelessHD.)
Set this to On if you are experiencing
bright over exposure of whites in your im‐
age. When set to On, HDMI Video Range
settings are disabled.
Power Con‐
sumption
High, Medium, ECO
You can set the lamp brightness to one of
three settings. Select ECO if the images
being projected are too bright. When
ECO, power consumption during projec‐
tion decreases, and fan noise is reduced.
Auto Iris
Off, Normal, High Speed
You can set the trackability of the function
to adjust the amount of light automatically
in accordance with changes in brightness
in the displayed image. Set to Off for no
luminance adjustment. s p.39
You can reset all adjustment values for
Image to their default settings.
*1 When pressing the up or down button on the adjustment screen, you can move to the previous or the next
adjustment menu.
*2 This is not displayed when a computer image signal is being input.
*3 When Color Mode is set to Natural, the settings change to 5000K - 10000K.
*4 Settings are saved for each type of input source or Color Mode.
Reset
Yes, No
76
Configuration Menu
Signal menu
Function
3D Setup*1
Menu/Settings
Explanation
3D Display
On, Off
Enables or disables the 3D image display func‐
tion. s p.46
2D-to-3D Conver‐
sion
Off, Weak, Medium, Sets the strength of the 3D effect when convert‐
Strong
ing 2D images to 3D images. s p.52
3D Format
Auto, Side by Side, Sets the 3D format for the input signal. When set
Top and Bottom, 2D to Auto, the format is recognized automatically.
3D Depth
-10 to 10
Sets the depth for the 3D image.
Diagonal Screen
Size
60 to 300
Sets the projection size for the 3D image. By
matching this to the actual size, you can achieve
the optimum 3D effect.
3D Brightness
Low, Medium, High Sets the brightness for the 3D image.
Inverse 3D Glasses
Yes, No
Reverses the synchronization timing for the left/
right shutters on the 3D Glasses and the left/right
images. Enable this function if the 3D effect is not
displayed correctly.
3D Viewing Notice
On, Off
Turns the notice that appears when viewing 3D
content on or off.
Aspect*2
Auto, Normal, Full, Zoom
Selects the aspect mode. s p.33
Tracking*2 *3
Varies depending on the input signal.
Adjusts computer images when vertical stripes
appear in the images.
Sync.*2 *3
0 to 31
Adjusts computer images when flickering, fuzzi‐
ness, or interference appear in the images.
• Adjusting the Brightness, Contrast, or Sharp‐
ness may cause flickering or blurriness.
• Adjusting the synchronization after adjusting
tracking allows for more accurate adjustments.
Position*2 *4
Deinterlac‐
ing*2
Adjusts the display position up, down, left, and
right when a part of the image is missing so that
the whole image is projected.
Off, Video, Film/Auto
(This can only be set when receiving signal input
from the Video port or when receiving 480i, 576i,
or 1080i signal input from the Component,
HDMI1, or HDMI2 ports or from WirelessHD.)
Converts the signal from interlaced (i) to pro‐
gressive (p) using a method appropriate for the
image signal.
• Off: This is ideal for dynamic motion images.
• Video: This is ideal for viewing general video
images.
• Film/Auto: Performs the optimal conversion for
film, CG, or animation input signals.
Motion Detec‐
tion*2 *5
1 to 5
Sets the image motion speed from 1 (slow, for
still images) to 5 (fast, for movies). Change this
setting if you are experiencing poor still image
quality or flickering movies.
77
Configuration Menu
Function
Super-resolu‐
tion*5
Menu/Settings
Explanation
0 to 5
Detail Enhance‐
ment
Reduces blurring that occurs at the edge of im‐
ages when the resolution is increased. s p.39
0 to 100
This setting enhances the contrast in an image
to create the image with more emphatic texture
and material feel. The higher the number is, the
stronger the enhancement effect is from the out‐
line area. s p.39
Auto Setup*3
On, Off
Advanced
Noise Reduc‐
tion*2 *5
Off, 1, 2, 3
(This can only be set when Image Processing is
set to Fine.)
Smoothes out rough images. There are three
modes available. Select your favorite setting.
It is recommended that this is set to Off when
viewing image sources in which noise is very low,
such as for DVDs.
Setup Level*2
0%, 7.5%
(This can be set when receiving an NTSC or com‐
ponent video signal from the Video port.)
Change this setting when using devices with a
different black level (Setup Level) such as prod‐
ucts designed for the Korean market. Check the
specifications for your connected device before
changing this setting.
Overscan*2 *5
Auto, Off, 2%, 4%,
6%, 8%
Changes the output image ratio (the range of the
projected image).
(Advanced)
Sets whether or not to automatically adjust the
image whenever the input signal is changed.
When enabled, the Tracking, Position, and
Sync. are automatically configured.
• Off, 2 to 8%: Sets the range of the image. Off
projects all ranges. Depending on the image sig‐
nal you may notice noise at the top and bottom
of the image.
• Auto: This can only be set when receiving signal
input from the HDMI1 or HDMI2 ports, or from
WirelessHD. This may be automatically set to
Off or 8% depending on the input signal.
HDMI Video
Range*2
Auto, Normal, Ex‐
panded
Image Processing*5 Fine, Fast
(This can only be set when EPSON Super
White is set to Off.)
When set to Auto, the video level for the DVD
input signal to the HDMI1 or HDMI2 port on the
projector is automatically detected and set.
If you experience under or overexposure when
set to Auto, set the video level of the projector
to match that of the DVD player's video level.
Your DVD player may be set to Normal or Expand.
The Auto option is not displayed when connec‐
ted to a connected device's DVI port.
Performs processing to improve the image qual‐
ity or response speed. s p.41
78
Configuration Menu
Function
Reset
Menu/Settings
Explanation
Yes, No
Resets all Signal settings except for Diagonal
Screen Size, 3D Viewing Notice, Aspect, and
Image Processing settings to their default set‐
tings.
*1 This is only displayed when an HDMI1, HDMI2, or WirelessHD image signal is being input. (WirelessHD is for EHTW6600W only.)
*2 Settings are saved for each type of input source or signal.
*3 This is only displayed when a PC image signal is being input.
*4 This is only displayed when a Component, PC, or Video image signal is being input.
*5 This is only displayed when a Component, HDMI1, HDMI2, Video, or WirelessHD image signal is being input
(WirelessHD is for EH-TW6600W only).
Settings menu
Function
H/V-Keystone
Audio
HDMI Link
Menu/Settings
Explanation
V-Keystone
-60 to 60
Performs vertical keystone correc‐
tion. s p.30
H-Keystone
-60 to 60
Performs horizontal keystone cor‐
rection. s p.30
Volume
Volume
Inverse Audio
On, Off
Sets whether or not to invert the left
and right audio output channels.
Set to On when the projector is sus‐
pended from a ceiling and is using
the internal speakers.
Device Connections
-
Displays a list of devices connected
from the HDMI1 or HDMI2 ports, or
from WirelessHD*.
HDMI Link
On, Off
Enables or disables the HDMI Link
function.
Audio Out Device
Projector, AV System, Wire‐
lessHD Transmitter*
Sets which device outputs audio
when using the HDMI Link function.
s p.68
Power On Link
Off, Bidirectional, Device -> PJ, Sets the link function when the
PJ -> Device
power is turned on.
Set to power on the projector when
content is played on a connected
device (Bidirectional or Device ->
PJ) or to power on a connected de‐
vice when the projector is turned on
(Bidirectional or PJ -> Device).
Power Off Link
On, Off
0 to 40
Adjusts the volume.
Sets whether or not to power off
connected devices when the pro‐
jector is turned off.
79
Configuration Menu
Function
WirelessHD*
Menu/Settings
Device Connections
-
Displays a list of available Wire‐
lessHD devices that can be connec‐
ted.
WirelessHD
On, Off
Enables or disables the WirelessHD
function.
Video Reception
Lock Setting
Explanation
Video Reception indicates the con‐
nection status with the WirelessHD
Transmitter. When the projector is
connected to the WirelessHD Trans‐
mitter and receives an image signal,
Transmitter detected appears.
WiHD Mode
Full, Dynamic
Sets the connection mode of Wire‐
lessHD devices.
Reset
Yes, No
Resets WirelessHD settings to their
default settings.
Note that even if you reset the pro‐
jector, the WirelessHD Transmitter
settings are not reset. To reset the
WirelessHD Transmitter, press the
Setup button on the base for 5 sec‐
onds or more. s p.54
Child Lock
On, Off
button on the
This locks the
projector's control panel to prevent
children from turning on the pro‐
jector by accident. You can turn on
the power when locked by holding
button for approxi‐
down the
mately three seconds. You can still
turn off the device using the
button, or perform operations with
the remote control as usual.
If changed, this setting is enabled
after you power off the projector
and the cool-down process is com‐
plete.
Note that even if Child Lock is set to
On, the projector still turns on when
the power cord is connected if Di‐
rect Power On is set to On.
Control Panel Lock
On, Off
When set to On, all buttons on the
control panel except for the
button are disabled.
is dis‐
played on the screen if any buttons
are pressed. To unlock, press and
hold the
button on the control
panel for at least 7 seconds.
If changed, this setting is enabled
once you close the Configuration
menu.
80
Configuration Menu
Function
Projection
Menu/Settings
Front, Front/Ceiling, Rear, Rear/Ceiling
Explanation
Change this setting depending on
how the projector is installed.
• Front: Select if you are projecting
in front of the screen.
• Front/Ceiling: Select if you are
projecting in front of the screen
suspended from the ceiling.
• Rear: Select if you are projecting to
a rear screen from the back.
• Rear/Ceiling: Select if you are pro‐
jecting to a rear screen from the
back when the projector is suspen‐
ded from the ceiling.
User Button
2D-to-3D Conversion, Power Consumption, Info
Select a Configuration menu item to
button on the
assign to the
remote control. By pressing the but‐
ton, the assigned menu item selec‐
tion/adjustment screen is dis‐
played, allowing you to make onetouch settings/adjustments.
Picture in Pic‐
ture
-
Starts the Picture in Picture display.
s p.72
81
Configuration Menu
Function
Operation
Menu/Settings
Explanation
Direct Power On
On, Off
You can set up the projector so that
projection starts as soon as the pow‐
er cord is plugged in without any
button operations.
Note that when this is set to On,
projection starts if power is restored
after a blackout or other power out‐
age and the power cord is still plug‐
ged into the projector.
Sleep Mode
Off, 5min., 10min., 20min.
If the set time is exceeded and no
signal is input, the projector is auto‐
matically turned off and enters
standby mode. When set to Off,the
projector never enters sleep mode.
When in standby mode, press the
button on the remote control or
the
button on the control panel
to start projection.
Illumination
On, Off
Set this to Off if the light from the
indicators on the control panel
bothers you when watching a mov‐
ie in a dark room.
Trigger Out
On, Off
Set the Trigger Out function to com‐
municate the projector's power on
status and so on to external devices.
When set to Off, no voltage is out‐
put from the Trigger Out port.
When set to On, voltage is output
from the Trigger Out port when the
projector is on.
If you change this setting, the new
setting will take effect the next time
you turn the projector on.
High Altitude Mode
On, Off
Set this to On if you are using the
projector above an altitude of 1500
meters.
82
Configuration Menu
Function
Display
Menu/Settings
Messages
On, Off
Explanation
Sets whether or not to display the
following messages (On or Off).
• Item names for image signals, color
modes, aspect ratios, and loading
memory.
• If the internal temperature is rising
when no image signal is being in‐
put or an unsupported signal is de‐
tected.
Panel Align‐
ment
Display Background
Black, Blue, Logo
Selects the screen status when no
image signal is being input.
Startup Screen
On, Off
Sets whether or not to show a start‐
up screen when projection begins
(On or Off). If changed, this setting
is enabled after you power off the
projector and the cool-down proc‐
ess is complete.
Standby Confirma‐
tion
On, Off
Sets whether or not to display a
standby confirmation message (On
or Off). s p.25
Panel Alignment
On, Off
Enables or disables Panel Align‐
ment.
Select Color
R, B
Select the color to correct.
Pattern Color
R/G/B, R/G, G/B
Select the pattern used for correc‐
tion.
Start Adjustments
-
Starts Panel Alignment. s p.40
Reset
Yes, No
Resets the correction value.
Language
-
Selects the display language.
Reset
Yes, No
All adjustment values for Settings
are returned to their default set‐
tings, except for the following.
•
•
•
•
•
•
•
•
* Only EH-TW6600W is displayed.
83
Inverse Audio
Audio Out Device
Power On Link
Power Off Link
Projection
User Button
High Altitude Mode
Language
Configuration Menu
Memory menu
Function
Explanation
Load Memory
Loads settings saved using the Save Memory function. s p.44
This cannot be selected if you have not saved any settings with the Save Mem‐
ory function.
Save Memory
Saves certain Image and Signal settings to memory. s p.43
Erase Memory
Erases settings saved to memory that you no longer need. s p.44
Rename Memory
Renames a saved memory. s p.44
Network menu
Function
Explanation
Net. Info. - Wireless LAN
Displays the following network setting status information.
•
•
•
•
•
•
•
•
•
•
•
Network Configuration
Connection Mode
Wireless LAN system
Antenna Level
Projector Name
SSID
DHCP
IP Address
Subnet Mask
Gateway Address
MAC Address
Region Code*
Takes you to the network configuration menu. s p.85
* This displays the available region information on your Wireless LAN unit. For more details, contact us at the
following address. s Epson Projector Contact List
Notes on Network menu operations
When you select the Network menu, the menu tabs are changed.
The basic operations are the same as those for the Configuration menu.
However, when exiting the menu, be sure to select the Setup complete and then save the settings.
Yes:
No:
Cancel:
Saves the settings and exits the Network menu.
Does not save the settings and exits the Network menu.
Continues the Network menu.
84
Configuration Menu
Soft keyboard operations
The Network menu displays a soft keyboard when input of alphanumerics is required during setup. Press the
buttons on the remote control or the
buttons on the control panel to
button to input them. Selecting Finish confirms your input, and selecting
select keys, and then press the
Cancel cancels your input.
CAPS key:
SYM1/2 key:
Sets and changes between upper case and lower case letters.
Sets and changes the symbol keys.
Basic menu
Function
Explanation
Displays the unique name used to identify this projector on a network.
When editing, you can enter up to 16 single-byte alphanumeric characters.
Projector Name
Wireless LAN
Function
Menu/Settings
Explanation
Wireless LAN Power
On, Off
Set whether or not (On/Off) to use a wireless LAN.
Selecting Off can prevent unauthorized access from outsid‐
ers.
Connection Mode
Quick, Advanced
Sets a wireless LAN connection mode.
Quick: The projector provides an access point. Connect a
computer or a smartphone directly to the projector.
Advanced: When having already established a wireless LAN
environment, connect the projector to the existing access
point.
Channel
1ch, 6ch, 11ch
(This can only be set when Connection Mode is set to Quick.)
Select the frequency band used for a wireless LAN.
SSID
-
(This can only be set when Connection Mode is set to Ad‐
vanced.)
Enter an SSID. When an SSID is specified in the wireless LAN
system where the projector participates, enter that SSID.
You can enter up to 32 single-byte alphanumeric characters.
Search Access Point
-
(This can only be set when Connection Mode is set to Ad‐
vanced.)
indicates the current access point.
indicates the access
point where security is ensured.
When selecting the access point where security is ensured,
you will be taken to the Security menu. s p.86
85
Configuration Menu
Function
Menu/Settings
Explanation
DHCP
Set whether or not (On/Off) to use DHCP. If specifying the
following address, set it to Off.
IP Address
Enter the projector's IP address.
The following IP addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
Subnet Mask
Enter the projector's subnet mask.
The following subnet masks cannot be used.
0.0.0.0, 255.255.255.255
Gateway Address
Enter the projector's gateway IP address.
The following gateway addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
SSID Display
On, Off
Set whether or not (On/Off) to display the SSID onto the LAN
standby screen.
IP Address Display
On, Off
Set whether or not (On/Off) to display the IP address onto the
LAN standby screen.
IP Settings
(This can only be set
when Connection
Mode is set to Ad‐
vanced.)
Security menu
Function
Menu/Settings
Explanation
Security
Off, WPA2-PSK, WPA/
WPA2-PSK
Set a security system.
In Quick, WPA2-PSK is selectable. In Advanced, WPA2PSK/WPA/WPA2-PSK is selectable.
Passphrase
-
Enter a passphrase.
The passphrase accepts 8 up to 32 single-byte alphanumeric
characters, and is case-sensitive.
In order to ensure security, it is recommended that you
change it periodically.
Reset menu
Function
Reset network settings.
Explanation
Resets all adjustment values for Network to their default settings.
86
Configuration Menu
Info menu
Function
Projector Info
Version
Menu/Settings
Explanation
Lamp Hours
Displays the cumulative lamp operating time.
Source
Displays the source name for the connected equipment cur‐
rently being projected.
Input Signal
Displays the input signal.
Resolution
Displays the resolution.
Scan Mode
Displays the scan mode.
Refresh Rate
Displays the refresh rate.
3D Format
Displays the 3D format of the signal input during 3D projec‐
tion (Frame Packing, Side by Side, or Top and Bottom).
Sync Info
Displays the image signal information.
This information may be needed if service is required.
Deep Color
Displays Deep Color.
Video Signal
Displays the signal type of the video device connected to the
Video port.
Status
This is information about errors that have occurred on the
projector.
This information may be needed if service is required.
Serial Number
Displays the projector's serial number.
Event ID
Displays the application error log. s p.101
Main
Displays the firmware version of the projector.
Video
Video2
Reset menu
Function
Explanation
Reset All
Resets all items in the Configuration menu to their default settings.
The following items are not reset to their defaults: Panel Alignment, Lamp
Hours, Language, Network, Memory.
Reset Memory
Erases all settings saved using the Save Memory function.
Reset Lamp Hours
Resets the cumulative lamp hours use time to 0 H. Reset when you replace the
lamp.
87
Configuration Menu
Picture in Picture menu
Displayed by pressing the
button during Picture in Picture projection.
Function
Picture in Pic‐
ture
Menu/Settings
Explanation
Subscreen Size
Small, Large
Changes the size of the sub screen.
s p.73
Subscreen Position
Top Right/Bottom Right/Top
Left/Bottom Left
Changes the position of the sub
screen.
Subscreen Source
HDMI1, HDMI2, WirelessHD*,
Component, Video, PC
Selects which source is displayed as
the sub screen. s p.73
Swap Main/Sub
Changes the main and sub screens.
s p.73
Exit Picture in Picture
Exits the Picture in Picture display.
s p.73
* Only EH-TW6600W is displayed.
88
Troubleshooting
Problem Solving
Reading the Indicators
You can check the status of the projector from the flashing and lit
on the control panel.
,
(operation indicators), o and m
Refer to the following table to check the projector's status and how to remedy problems shown by the
indicators.
Indicator status during an error/warning
: Lit
Indicators
Status
: Flashing
: Status maintained
: Off
Remedy
Replace Lamp
It is time to replace your lamp. Replace the lamp with a new
lamp as soon as possible. s p.106
The lamp may explode if you continue to use it in this status.
High Temp Warning
You can continue projecting. If the temperature rises too high
again, projection stops automatically.
(blue)/(orange)
• If the projector is installed next to a wall, make sure there is at
(blue)/(orange)
least 20 cm between the wall and the projector's exhaust vent.
• If the air filter is clogged, clean it. s p.102
89
Troubleshooting
Indicators
Status
Internal Error
Remedy
The projector has malfunctioned.
Remove the power plug from the electrical outlet, and contact
your local dealer or the nearest Epson repair center. s Epson
Projector Contact List
(blue)/(orange)
Fan Error
Sensor Error
(blue)/(orange)
Auto Iris Error
(blue)/(orange)
Power Err. (Ballast)
(blue)/(orange)
Lamp Error
There is a problem with the lamp, or it failed to turn on.
Lamp Failure
• Disconnect the power cord, and then check if the lamp is
cracked. s p.106
If it is not cracked, reinstall the lamp and turn on the power.
If reinstalling the lamp does not fix the problem, or if the lamp
is cracked, remove the power plug from the electrical outlet,
and contact your local dealer or the nearest Epson repair center.
s Epson Projector Contact List
• Check that the lamp cover has been properly closed.
(blue)/(orange)
High Temp Error
(Overheating)
(blue)/(orange)
The internal temperature is too high.
• The lamp turns off automatically and projection stops. Wait for
•
•
•
•
about five minutes. When the fan has stopped, disconnect the
power cord.
If the projector is installed next to a wall, make sure there is at
least 20 cm between the wall and the projector's exhaust vent.
If the air filter is clogged, clean it. s p.102
If turning the power back on does not clear the problem, stop
using the projector and remove the power plug from the elec‐
trical outlet. Contact your local dealer or the nearest Epson re‐
pair center. s Epson Projector Contact List
When using at an altitude of 1500 m or more, set High Altitude
Mode to On. s Settings - Operation - High Altitude
Mode p.79
90
Troubleshooting
Indicator status during normal operation
: Lit
Indicators
Status
Standby condition
: Flashing
: Off
Remedy
When you press the
button on the remote control, or the
button on the control panel, projection starts after a short
wait.
Warm-up in progress Warm-up time is about 30 seconds.
The power-off operation is disabled while the projector is warm‐
ing-up.
(blue)
Cool-down in pro‐
gress
All operations are disabled while the projector is cooling-down.
The projector enters standby condition when cool-down is com‐
plete. If for any reason the power cord is disconnected during
cool-down, wait until the lamp has cooled down sufficiently
(about 10 minutes), reconnect the power cord, and then press
button on the remote control, or the
button on the
the
control panel.
Projection in pro‐
gress
The projector is operating normally.
(blue)
c
• Under normal operating conditions, the o and m indicators are off.
• When the Illumination function is set to Off, all indicators are off under normal projection conditions.
s Settings - Operation - Illumination p.79
91
Troubleshooting
When the Indicators Provide No Help
Check the problem
Check the following table to see if your problem is mentioned, and go to the appropriate page for information
on handling the problem.
Problem
Problems relating to im‐
ages
Page
No images appear
p.93
Projection does not start, the projection area is completely black, or
the projection area is completely blue.
Moving images being projected from a computer are not projected
p.93
"Not supported" is displayed
p.93
"No Signal" is displayed
p.94
Images are fuzzy or out of focus
p.94
Interference or distortion appears in the images
p.94
The image is truncated (large) or small, or only a part of the image is
projected
p.95
Image colors are not right
p.95
The whole image appears purplish or greenish, images are black &
white, or colors appear dull.*
Images appear dark
p.95
Projection stops automatically
p.96
Problems when projection The projector does not turn on
starts
p.96
Problems with the remote The remote control does not respond
control
p.96
Problems with the control
panel
Cannot make settings on the control panel
p.97
Problems with 3D
Cannot project correctly in 3D
p.97
The 3D image is enlarged and truncated
p.98
HDMI Link does not function
p.98
The device name is not displayed under device connections
p.98
Problems with HDMI
Problems with WirelessHD Cannot project WirelessHD images
p.98
WirelessHD audio is not output correctly
p.99
Interference, distortion, or interruption appear in WirelessHD
p.99
Problems with USB storage Slideshow does not start
devices
p.100
Other problems
p.100
No audio, or the audio is too low
A network cannot be connected via a wireless LAN
p.100
* Because color reproduction differs between monitors and computer LCD screens, the image projected by the
projector and the color tones displayed on the monitor may not match, however this is not a fault.
92
Troubleshooting
Problems relating to images
No images appear
Check
Remedy
Is the projector turned on?
Press the
button on the remote control or the
on the control panel.
Is the power cord connected?
Connect the power cord.
Are the indicators switched off?
Disconnect and then reconnect the projector's power cord.
Check that pressing the power button after connection supplies
the projector with power.
Is an image signal being input?
Check that the connected device is turned on. When Messag‐
es is set to On from the Configuration menu, image signal mes‐
sages are displayed. s Settings - Display - Messages p.79
Has the power to the AV amplifier been dis‐
connected?
If an AV amplifier is connected, check the AV amplifier's power
supply.
button
Is an image signal being sent from the device? Check that an image signal is being sent from the connected
device.
Are the Configuration menu settings correct? Reset all of the settings. s Reset - Reset All p.87
(Only when projecting computer image sig‐
nals)
If the connection is made while the power is already turned on,
the key (Function key and so on) that changes the computer's
image signal to external output may not work. Turn off the con‐
Was the connection made while the power of
nected computer, and then turn it back on.
the projector or the computer was already
turned on?
Moving images are not displayed
Check
Remedy
(Only when projecting computer image sig‐
nals)
Depending on the computer's specifications, moving images
may not be displayed when the computer is set to external out‐
put and to the LCD monitor output at the same time.
Is the computer's image signal set to external
Change it so that the image signal is set to external output only.
output and to output to the LCD monitor at
For the computer's specifications, see the documentation sup‐
the same time?
plied with the computer.
"Not supported" is displayed.
Check
Remedy
(Only when projecting computer image sig‐
nals)
Check the image signal being input in Resolution from the Con‐
figuration menu, and check that it corresponds to the projector's
resolution. s p.110
Do the image signal's frequency and resolu‐
tion correspond to the mode?
93
Troubleshooting
"No Signal" is displayed.
Check
Remedy
Are the cables connected correctly?
Check that all the cables required for projection are securely
connected. s p.18
Is the correct image input port selected?
Change the image with the source buttons on the remote con‐
button on the control panel. s p.25
trol, or the
Is the connected device turned on?
Turn on the device.
(Only when projecting computer image sig‐
nals)
Change it so that the image signal is set to external output, and
not just the computer's LCD monitor. For some models, when
the image signals are output externally, they no longer appear
on the LCD monitor.
For the computer's specifications, see the documentation sup‐
plied with the computer.
Are the image signals being output to the
projector?
If the connection is made while the power of the projector or the
computer is already turned on, the Fn key (Function key) that
changes the computer's image signal to external output may not
work. Turn off the computer and the projector, and then turn
them back on.
Keystone distortion of projected image
Check
Remedy
Is keystone distortion adjusted within the cor‐ If projecting the image from outside of the correctable range,
rection range?
you may not be able to correct the keystone distortion com‐
pletely. Install the projector horizontally in front of the screen as
far as possible, and then adjust the projection position using lens
shift. s p.13
Images are fuzzy or out of focus
Check
Remedy
Has the focus been adjusted?
Adjust the focus. s p.27
Is the lens cap attached?
Remove the lens cap.
Is the projector at the correct distance?
Check the recommended projection range. s p.15
Has condensation formed on the lens?
If the projector is suddenly taken from a cold environment to a
warm environment, or if sudden ambient temperature changes
occur, condensation may form on the surface of the lens, and this
may cause the images to appear fuzzy. Set the projector up in
the room about one hour before it is used. If the projector is wet
from condensation, turn off the projector, disconnect the power
cord, and leave it for a while.
Interference or distortion appear in images
Check
Are the cables connected correctly?
Remedy
Check that all the cables required for projection are securely
connected. s p.18
94
Troubleshooting
Check
Is an extension cable being used?
Remedy
If an extension cable is used, electrical interference may affect
the signals.
(Only when projecting computer image sig‐
nals)
The projector uses automatic adjustment functions to project at
the optimum status. However, depending on the signal, some
may not be adjusted correctly even after performing self correc‐
Are the Sync. and Tracking settings adjusted
tions. If this happens, adjust the Tracking and Sync. settings
correctly?
from the Configuration menu. s Signal - Tracking/Sync. p.77
(Only when projecting computer image sig‐
nals)
Set the computer so that the signals being output are compatible
with the projector. s p.110
Is the correct resolution selected?
Part of the image is truncated (large) or small
Check
Remedy
Is the correct Aspect selected?
button, and then select the Aspect that match‐
Press the
es the input signal. s Signal - Aspect p.77
Is the image Position adjusted correctly?
Adjust the Position setting from the Configuration menu.
s Signal - Position p.77
(Only when projecting computer image sig‐
nals)
Set the computer so that the signals being output are compatible
with the projector. s p.110
Is the correct resolution selected?
Image colors are not right
Check
Are the cables connected correctly?
Is the contrast adjusted correctly?
Remedy
Check that all the cables required for projection are securely
connected. s p.18
For the Video and Component ports, make sure the connector is
the same color as the cable port. s p.18
Adjust the Contrast setting from the Configuration menu.
s Image - Contrast p.75
Is the color adjusted correctly?
Adjust the Advanced setting from the Configuration menu.
s Image - Advanced p.75
(Only when projecting images from a video
device)
Adjust the Color Saturation and Tint settings from the Config‐
uration menu. s p.75
Are the color saturation and tint adjusted cor‐
rectly?
Images appear dark
Check
Is the image brightness set correctly?
Is the contrast adjusted correctly?
Remedy
Adjust the Brightness setting from the Configuration menu.
s Image - Brightness p.75
Adjust the Contrast setting from the Configuration menu.
s Image - Contrast p.75
95
Troubleshooting
Check
Is it time to replace the lamp?
Remedy
When the lamp is nearly ready for replacement, the images be‐
come darker and the color quality becomes poorer. When this
happens, replace the lamp with a new lamp. s p.106
Projection stops automatically
Check
Is Sleep Mode enabled?
Remedy
If the set time is exceeded and no signal is input, the lamp turns
off automatically, and the projector enters standby status. The
projector returns from standby status when you press the
button on the remote control or the
button on the control
panel. If you do not want to use Sleep Mode, change the setting
to Off. s Settings - Operation - Sleep Mode p.79
Problems when projection starts
The projector does not turn on
Check
Remedy
Is the power turned on?
button on the remote control or the
Press the
on the control panel.
Is Child Lock set to On?
When Child Lock is set to On from the Configuration menu, hold
button on the control panel for approximately
down the
three seconds, or perform operations from the remote control.
s Settings - Lock Setting - Child Lock p.79
Do the indicators turn on and off when the
power cord is touched?
Turn off the projector, and then disconnect and reconnect the
projector's power cord. If the problem continues, stop using the
projector, remove the power plug from the electrical outlet, and
contact your local dealer or the nearest projector information
center. s Epson Projector Contact List
button
Problems with the remote control
The remote control does not respond
Check
Remedy
Is the remote control light-emitting area
Point the remote control towards the remote receiver. Also,
pointing towards the remote receiver on the check the operating range. s p.23
projector during operation?
Is the remote control too far from the projec‐ Check the operating range. s p.23
tor?
Is direct sunlight or strong light from fluores‐ Set the projector up in a location where strong light does not
cent lamps shining onto the remote receiver? shine onto the remote receiver.
Are the batteries dead or have the batteries
been inserted correctly?
Make sure the batteries are inserted correctly or replace the bat‐
teries with new ones if necessary. s p.23
96
Troubleshooting
Check
Remedy
Make sure you point the remote control at the WirelessHD Trans‐
Is the remote control pointed at the Wire‐
lessHD Transmitter when operating the WiHD mitter when using the WiHD Transmitter control button on the
remote control. s p.62
Transmitter control button?
(EH-TW6600W only)
Problems with the control panel
Cannot make settings on the control panel
Check
Is Control Panel Lock set to On?
Remedy
If Control Panel Lock is set to On from the Configuration menu,
all of the control panel buttons except for
button are disa‐
bled. Perform operations from the remote control. s Settings
- Lock Setting - Control Panel Lock p.79
Problems with 3D
Cannot project correctly in 3D
Check
Remedy
Are the 3D Glasses turned on?
Turn on the 3D Glasses.
Is a 3D image being projected?
If the projector is projecting a 2D image, or if an error occurs on
the projector that prevents the 3D image from being projected,
you cannot view 3D images even if you are wearing the 3D
Glasses.
Is the input image in 3D?
Check that the input image is 3D compatible.
Since most TV broadcasts do not contain a 3D format signal, 3D
reception must be set manually.
Is 3D Display set to Off?
If 3D Display is set to Off from the Configuration menu, the pro‐
jector does not automatically change to 3D even when a 3D im‐
button. s Signal - 3D Setup - 3D
age is input. Press the
Display p.77
Is the correct 3D format set?
The projector automatically selects the appropriate 3D format,
but if the 3D image is not displayed correctly, use 3D Format
from the Configuration menu to select another format. s Sig‐
nal - 3D Setup - 3D Format p.77
Are you viewing within the reception range? Check the range within which the 3D Glasses can communicate
with the projector, and view within that range. s p.49
Has pairing been performed correctly?
See the User's Guide for the 3D Glasses to perform pairing.
Are there any devices that cause radio wave
interference in the vicinity?
When using other devices at the same time with the frequency
band (2.4 GHz) such as Bluetooth communication devices, wire‐
less LAN (IEEE802.11b/g), or microwave ovens, radio wave inter‐
ference may occur, the image may be interrupted, or communi‐
cation may not be possible. Do not use the projector near these
devices.
97
Troubleshooting
The 3D image is enlarged and truncated
Check
Is the correct 3D video format set?
Remedy
Video may be truncated if an incorrect 3D format is set. Set the
correct 3D format. s p.46
Problems with HDMI
HDMI link does not function
Check
Remedy
Are you using a cable that meets the HDMI
standards?
Operations are not possible with cables that do not meet the
HDMI standards.
Does the connected device meet the HDMI
CEC standards?
If the connected device does not meet the HDMI CEC standards,
it cannot be operated even if it is connected to the HDMI port.
See the documentation and so on supplied with the connected
device for more information.
button, and then check if the device is
Also, press the
available under Device Connections. s p.69
Are the cables connected correctly?
Check that all the cables required to use HDMI Link are securely
connected. s p.68
Is the power for the amplifier or DVD recorder Put each device in standby status. See the documentation and
and so on turned on?
so on supplied with the connected device for more information.
If you have connected a speaker and so on, set the connected
device to PCM output.
Was a new device connected, or was the con‐ If the CEC function for a connected device needs to be set again,
nection changed?
for example when a new device is connected or the connection
is changed, you may need to restart the device.
Are too many multi-media players connec‐
ted?
Up to 3 multi-media players that meet the HDMI CEC standards
can be connected at the same time.
The device name is not displayed under Device Connections
Check
Does the connected device meet the HDMI
CEC standards?
Remedy
If the connected device does not meet the HDMI CEC standards,
it is not displayed. See the documentation and so on supplied
with the connected device for more information.
Problems with WirelessHD (EH-TW6600W only)
Cannot project WirelessHD images
Check
Remedy
Does the cable connecting the supplied Wire‐ If the cable does not meet the HDMI standards, operations are
lessHD Transmitter meet the HDMI stand‐
not possible.
ards?
98
Troubleshooting
Check
Remedy
Is WirelessHD set to Off?
When WirelessHD is set to Off from the Configuration menu,
projection is not possible for WirelessHD input signals. Set Wire‐
lessHD to On, and then press the
button. s Settings WirelessHD p.79
Are signals being received within the Wire‐
lessHD transmission range?
Check the range within which the WirelessHD's transceiver can
communicate, and view within that range. s p.61
Is the supplied WirelessHD Transmitter
turned on?
Check the power lamp on the WirelessHD Transmitter. If there is
no power being supplied, make sure the connector for the AC
adapter is securely connected, and then turn on the power
switch.
Is the WirelessHD indicator for the supplied
WirelessHD Transmitter off?
No signal is output from the AV device connected to the Wire‐
lessHD Transmitter. Check that the cables from the AV device and
the WirelessHD Transmitter are securely connected.
When you last viewed the images that had been output to a
monitor device, such as television, via the Output port, the im‐
ages will be projected on the same monitor device as the last one
the next time the projector is turned on. To cancel the setting,
button (switch output) on the remote control
press the
while pointing it at the WirelessHD Transmitter. s p.63
Is the Link indicator for the supplied Wire‐
lessHD Transmitter off?
The WirelessHD cannot communicate with the projector. Check
the range within which the WirelessHD's transceiver can com‐
municate, and setup within that range.
Has dust collected in the WirelessHD Trans‐
mitter's vent?
Has dust collected in the WirelessHD Transmitter's vent? Com‐
munication may not be possible if dust has collected in the vent.
Install the projector so that dust does not collect in the vent.
Are the projector and the WirelessHD Trans‐
mitter facing the correct way?
Setup the projector and the WirelessHD Transmitter so that they
are facing each other.
Is "Source: WirelessHD X"/"No Signal" dis‐
played in the lower-left part of the screen?
Check that the AV device connected with the HDMI port on the
WirelessHD Transmitter is turned on. The input signal number
displayed on the screen is the same as the HDMI port number.
In addition, unless HDMI Link is set to On, the connected device
does not turn on. Set HDMI Link to On. s Settings - HDMI
Link - HDMI Link p.79
WirelessHD audio is not output correctly.
Check
Remedy
Is audio output when the WirelessHD is con‐ When connecting a device, such as a sound bar, to the Optical
nected?
Audio-Out port on the WirelessHD Transmitter to output audio
from there, set Audio Out Device to WirelessHD Transmitter.
The connected sound bar must be set to surround sound. To
output audio from the projector, set it to Projector. s Set‐
tings - HDMI Link - Audio Out Device p.79
Interference, distortion, or interruption appear in WirelessHD
Check
Are signals being received within the Wire‐
lessHD transmission range?
Remedy
Check the range within which the WirelessHD's transceiver can
communicate, and view within that range. s p.61
99
Troubleshooting
Check
Remedy
Are there any obstructions between the Wire‐ Because WirelessHD communicates using a tight beamed elec‐
lessHD Transmitter and the projector?
tromagnetic wave, if there are any people or objects and so on
obstructing the communication path, this could have an adverse
affect on the image. Make sure that there are no obstacles be‐
tween the WirelessHD Transmitter and the projector within the
WirelessHD transmission range. s p.61
Is the reception too low?
If the transmissions are not strong enough, communication may
be unstable.
Check Video Reception as you set up the transmitter as it is
sometimes possible to improve the strength of the transmission
by moving the WirelessHD Transmitter or changing its direction.
s Settings - WirelessHD - Video Reception p.79
Transmission strength may differ depending on the surround‐
ings, or they may be unstable. While checking Video Recep‐
tion, setup the transmitter in a location where the number dis‐
played remains steady. s Settings - WirelessHD - Video Re‐
ception p.79
Problems with USB storage devices
Slideshow does not start
Check
Is the USB storage device using a security
function?
Remedy
You may not be able to use USB storage devices that incorporate
security functions.
Other problems
No audio, or the audio is too low
Check
Remedy
Is the audio cable connected correctly?
Try disconnecting the cable from the Audio (L-R) port, and then
reconnecting.
Is the volume too low?
Adjust the volume so that you can hear the audio. s p.31
Is it connected with an HDMI cable?
If no audio is output when connecting via an HDMI cable, set the
connected equipment to PCM output.
A network cannot be connected via a wireless LAN
Check
Remedy
Is the passphrase correct?
Be aware that the passphrase is case-sensitive. If forgetting your
passphrase, set a new one again.
Have you checked the Event ID?
Check the number of the Event ID, and try the following remedy.
s p.101
The Event ID can be checked from the Info menu. s Info Projector Info - Event ID p.87
100
Troubleshooting
Event ID
Check the number, and try the remedy as follows. If the problem persists, contact your local dealer or the
nearest Epson repair center.
s Epson Projector Contact List
Event ID
Cause
Remedy
0432
0435
The EasyMP Network Projection failed to be
started.
0434
0481
0482
0485
The network communication status is unstable. Check the network communication status, and
reconnect it after a while.
0433
Transferred images cannot be played.
0484
Communication was disconnected from the
computer.
0483
04FE
The EasyMP Network Projection exited unex‐
pectedly.
Check the network communication status, and
restart the projector.
0479
04FF
A system error occurred in the projector.
Restart the projector.
0891
The access point with the same SSID cannot be Set the same SSID as that of the computer and
found.
the access point to the projector.
0892
The authentic methods of WPA/WPA2 are in‐
consistent.
0894
Communication was disconnected because of Check with your network administrator and fol‐
the connection with an unauthorized access
low his/her instructions.
point.
0898
DHCP failed to be acquired.
Check that the DHCP server is operating cor‐
rectly. If not using DHCP, turn off the DHCP set‐
ting.
0899
Other connection-related errors
If the problem persists even after the projector
or the EasyMP Network Projection is restarted,
contact us at the following address. s Epson
Projector Contact List
101
Restart the projector.
Restart the EasyMP Network Projection.
Check that the wireless LAN security settings
are correct.
Maintenance
Maintenance
Cleaning the Parts
You should clean the projector if it becomes dirty or if the quality of projected images starts to deteriorate.
Warning
Do not use sprays that contain flammable gas to remove dirt and dust from the projector's lens, air filter,
and so on. The projector may catch fire due to the high internal temperature of the lamp.
Cleaning the air filter
Clean the air filter if dust has accumulated on the air filter or when the following message is displayed.
"The projector is overheating. Make sure nothing is blocking the air vent, and clean or replace the air
filter."
Attention
• If dust collects on the air filter, it can cause the internal temperature of the projector to rise, and this can lead
to problems with operation and shorten the optical engine's service life. It is recommended that you clean
the air filter at least once every three months. Clean them more often than this if using the projector in a
particularly dusty environment.
• Do not rinse the air filter in water. Do not use detergents or solvents.
• Lightly brush the air filter to clean it. If it is brushed too strongly, dust will be ground into the air filter and
cannot be removed.
a
Press the
button on the remote
control or the control panel to turn off
the power, and then disconnect the
power cord.
b
Remove the air filter cover.
c
Hook your finger into the tab on the air filter
cover, and remove it downward.
102
Remove the air filter.
Grip the knob in the center of the air filter
and pull it out.
Maintenance
d
Hold the air filter with the surface
facing down and tap it 4 or 5 times to
remove the dust.
f
Install the air filter.
g
Install the air filter cover.
Grip the air filter by the knob in the center
and insert it straight.
Turn it over and tap the other side in the
same way.
Attention
Fasten the upper catch and then the lower
one.
If the air filter is hit too hard, it may
become unusable due to deformities
and cracks.
e
Remove any dust remaining on the air
filter by using a vacuum cleaner from
the front side.
Cleaning the main unit
Clean the projector's surface by wiping it gently with a soft cloth.
If it is particularly dirty, moisten the cloth with water containing a small amount of neutral detergent, and
then firmly wring the cloth dry before using it to wipe the surface.
Attention
Do not use volatile substances such as wax, alcohol, or thinner to clean the projector's surface. The quality
of the case may change or the paint may peel off.
103
Maintenance
Cleaning the lens
Use a commercially available cloth for cleaning glasses to gently wipe off dirt from the lens.
Attention
Do not rub the lens with harsh materials or handle the lens too roughly as it can easily become damaged.
Cleaning the 3D Glasses
Use the cloth to gently wipe off dirt from the lenses of the 3D
Glasses.
Attention
• Do not rub the lenses of the glasses with harsh materials or
handle the lenses too roughly as they can easily become
damaged.
• When maintenance is necessary, disconnect the USB Charg‐
ing Adapter from the electrical outlet, and check that all ca‐
bles have been disconnected.
• The 3D glasses contain rechargeable batteries. Observe local
regulations when you dispose of them.
Replacement Periods for Consumables
Air filter replacement period
• If the message is displayed even though the air filter has been cleaned s p.102
Lamp replacement period
• The following message is displayed when projection starts
"It is time to replace your lamp. Please contact your Epson projector reseller or visit www.epson.com to
purchase."
• The projected image gets darker or starts to deteriorate.
c
• The lamp replacement message is set to appear after 3400H in order to maintain the initial brightness
and quality of the projected images. The message display time changes depending on the usage
situation, such as the color mode setting and so on.
If you continue to use the lamp after the replacement period has passed, the possibility that the lamp
may explode increases. When the lamp replacement message appears, replace the lamp with a new
one as soon as possible, even if it is still working.
• Depending on the characteristics of the lamp and the way it has been used, the lamp may become
darker or stop working before the lamp warning message appears. You should always have a spare
lamp unit ready in case it is needed.
104
Maintenance
Replacing Consumables
Replacing the air filter
c
Dispose of used air filters properly in accordance with your local regulations.
Material: Polypropylene
a
Press the
button on the remote
control or the control panel to turn off
the power, and then disconnect the
power cord.
b
Remove the air filter cover.
c
d
Install the new air filter.
e
Install the air filter cover.
Grip the air filter by the knob in the center
and insert it straight.
Hook your finger into the tab on the air filter
cover, and remove it downward.
Remove the old air filter.
Grip the knob in the center of the air filter
and pull it out.
105
Fasten the outside catch and then the
lower one.
Maintenance
Replacing the lamp
Warning
When replacing the lamp because it has stopped illuminating, there is a possibility that the lamp may be
broken. If replacing the lamp of a projector that has been suspended from the ceiling, you should always
assume that the lamp is cracked, and remove the lamp cover with care. When you open the lamp cover,
small shards of glass could fall out. If any shards of glass get into your eyes or mouth, contact a doctor
immediately.
Caution
• Do not touch the lamp cover immediately after turning off the projector as it is still hot. Wait until the lamp
has cooled down sufficiently before removing the lamp cover. Otherwise, you could get burnt.
• We recommend the use of genuine EPSON option lamps. The use of non-genuine lamps may affect projection
quality and safety.
Any damage or malfunction caused by the use of non-genuine lamps may not be covered by Epson's warranty.
a
Press the
button on the remote
control or the control panel to turn off
the power, and then disconnect the
power cord.
b
Loosen the lamp cover fixing screw.
c
Remove the lamp cover.
Slide the lamp cover straight forward and
remove it.
106
d
Loosen the two lamp fixing screws.
e
Remove the old lamp.
Grip the knob firmly and pull it straight out.
Maintenance
f
Install the new lamp.
g
Tighten the two lamp fixing screws.
Make sure the lamp is facing the correct
direction and press it in.
h
Replace the lamp cover.
i
Tighten the lamp cover fixing screw.
Slide the cover back into place.
Warning
Do not disassemble or remodel the lamp. If a modified or disassembled lamp is installed in the projector
and used, it could cause a fire, electric shock, or an accident.
Caution
• Make sure you install the lamp and lamp cover securely. If they are not installed correctly, the power does
not turn on.
• The lamp contains mercury (Hg). Dispose of used lamps in accordance with your local laws and regulations
on disposing of fluorescent tubing.
107
Maintenance
Resetting lamp hours
After replacing the lamp, make sure you reset the lamp hours.
The projector records how long the lamp is turned on and a message and indicator notify you when it is time
to replace the lamp.
a
Turn on the power.
b
Press the
c
Select Reset - Reset Lamp Hours.
d
button.
Use the
buttons to select Yes,
and then press the
button to
execute.
The lamp hours are reset.
The Configuration menu is displayed.
A reset confirmation message is displayed.
108
Appendix
Optional Accessories and Consumables
The following optional accessories and consumables are available for purchase if required. This list of optional
accessories and consumables is current as of: 2014.7. Details of accessories are subject to change without
notice.
Availability may vary depending on the country of purchase.
Optional Items
Name
Ceiling mount*
Model No.
ELPMB20
Explanation
Use when installing the projector on a ceiling.
ELPMB22
ELPMB30
Ceiling pipe 450 (450 mm white)*
ELPFP13
Ceiling pipe 700 (700 mm white)*
ELPFP14
Active shutter 3D Glasses
ELPGS03
These are Bluetooth active shutter 3D glasses.
Use when viewing 3D images with this projector.
USB Charging Adapter
ELPAC01
Use when charging the 3D Glasses.
Wireless LAN unit
ELPAP07
Use when connecting an external device to the
projector via a wireless LAN to project images.
Use when installing the projector on a high ceil‐
ing.
802.11b/g/n (2.4 GHz)
* Special expertise is required to suspend the projector from a ceiling. Contact your local dealer.
Consumables
Name
Model No.
Explanation
Lamp unit
ELPLP85
Use as a replacement for used lamps. (1 lamp)
Air filter
ELPAF39
Use as a replacement for used air filters. (1 air filter)
109
Appendix
Supported Resolutions
Component Video
Signal
Refresh Rate (Hz)
Resolution (dots)
SDTV (480i)
60
720 x 480
SDTV (576i)
50
720 x 576
SDTV (480p)
60
720 x 480
SDTV (576p)
50
720 x 576
HDTV (720p)
50/60
1280 x 720
HDTV (1080i)
50/60
1920 x 1080
HDTV (1080p)
50/60
1920 x 1080
Composite Video
Signal
Refresh Rate (Hz)
Resolution (dots)
TV (NTSC)
60
720 x 480
TV (SECAM)
50
720 x 576
TV (PAL)
50/60
720 x 576
Computer Signals (Analog RGB)
Signal
Refresh Rate (Hz)
Resolution (dots)
VGA
60
640 x 480
SVGA
60
800 x 600
XGA
60
1024 x 768
SXGA
60
1280 x 960
60
1280 x 1024
60
1280 x 768
60
1366 x 768
60
1280 x 800
60
1600 x 900
WXGA
WXGA++
HDMI1/HDMI2 Input Signal
Signal
Refresh Rate (Hz)
Resolution (dots)
VGA
60
640 x 480
SDTV (480i)
60
720 x 480
SDTV (576i)
50
720 x 576
110
Appendix
Signal
Refresh Rate (Hz)
Resolution (dots)
SDTV (480p)
60
720 x 480
SDTV (576p)
50
720 x 576
HDTV (720p)
50/60
1280 x 720
HDTV (1080i)
50/60
1920 x 1080
HDTV (1080p)
24/30/50/60
1920 x 1080
MHL Input Signal
Signal
Refresh Rate (Hz)
Resolution (dots)
VGA
60
640 x 480
SDTV (480i)
50
720 x 480
SDTV (576i)
60
720 x 576
SDTV (480p)
50
720 x 480
SDTV (576p)
60
720 x 576
HDTV (720p)
50/60
1280 x 720
HDTV (1080i)
50/60
1920 x 1080
HDTV (1080p)
24/30
1920 x 1080
3D Input Signal HDMI
Signal
Refresh Rate Resolution (dots)
(Hz)
3D Format
Frame Pack‐
ing
Side by Side
Top and Bot‐
tom
HDTV (720p)
50/60
1280 x 720
HDTV (1080i)
50/60
1920 x 1080
-
-
HDTV (1080p)
50/60
1920 x 1080
-
-
HDTV (1080p)
24
1920 x 1080
WirelessHD Input Signal
Signal
Refresh Rate (Hz)
Resolution (dots)
VGA
60
640 x 480
SDTV (480i)
60
720 x 480
SDTV (576i)
50
720 x 576
SDTV (480p)
60
720 x 480
SDTV (576p)
50
720 x 576
HDTV (720p)*
50/60
1280 x 720
HDTV (1080i)
50/60
1920 x 1080
HDTV (1080p)*
24/50/60
1920 x 1080
111
Appendix
* When projecting in WirelessHD, the following signals do not support Deep Color.
2D: 1080p 60/50 Hz
3D: 1080P 24 Hz frame packing/720P 50/60 Hz frame packing/1080p 60/50 Hz side by side
3D Input Signal MHL (via a WirelessHD Transmitter*)
Signal
Refresh Rate Resolution (dots)
(Hz)
3D Format
Frame Pack‐
ing
HDTV (720p)
50/60
1280 x 720
-
HDTV (1080i)
50/60
1920 x 1080
-
HDTV (1080p)
50/60
1920 x 1080
-
HDTV (1080p)
24
1920 x 1080
-
* HDMI5 port only
112
Side by Side
Top and Bot‐
tom
-
-
-
Appendix
Specifications
Product name
EH-TW6600W
EH-TW6600
Appearance (not including ad‐ 410 (W) x 157 (H) x 304 (D) mm
justable foot)
Panel Size
0.61" wide
Display method
Polysilicon TFT active matrix
Resolution
1920 (W) x 1080 (H) x 3
Scanning
Frequency
Digital
Pixel clock: 13.5 - 148.5 MHz
Horizontal: 15.63 - 67.5 kHZ
Vertical: 24, 30, 50 - 60 Hz
Analog
Pixel clock: 13.5 - 148.5 MHz
Horizontal: 15.63 - 67.5 kHZ
Vertical: 50 - 60 Hz
Focus adjustment
Manual
Zoom adjustment
Manual (approx. 1 to 1.6)
Lamp (light source)
UHE lamp 250 W, Model No.: ELPLP85
Power supply
100 - 240 V AC ±10%, 50/60 Hz, 3.9-1.8 A
Power con‐ 100 to 120 V area Operating: 385 W
sumption
Standby power consumption: 0.29 W
Standby power consumption: 1.6 W*1
220 to 240 V area Operating: 366 W
Standby power consumption: 0.43 W
Standby power consumption: 1.8 W*1
Operating altitude
Altitude 0 to 3000 m
Operating temperature
+5 to 35°C*2 (No condensation)
Storage temperature
-10 to +60°C (No condensation)
Mass
Approx. 6.8 kg
Connectors
Component port x 1, 3RCA pin jack
Approx. 6.7 kg
PC port x 1, Mini D-Sub15-pin (female) blue
HDMI port x 2, HDMI
For HDCP, For CEC signals, For MHL signals (HDMI1 port only), For linear
PCM, Deep Color
Video port x 1, RCA pin jack
RS-232C port x 1, D-sub 9-pin (male)
Trigger Out port x 1, 3.5 mm mini jack
Audio-L/R port x 1, RCA pin jack
Audio Out port x 1, stereo mini-pin jack
USB 2.0 TypeA port x 1
Speaker
10 W x 2
113
Appendix
*1 When using the WirelessHD Transmitter with EH-TW6600W, and the following conditions are satisfied
Settings - WirelessHD - WirelessHD is set to On
Settings - HDMI Link - Power On Link is set to Bidirectional or Device -> PJ s p.79
*2 For use at an altitude of 2286 m or higher, it is +5 to +30°C.
This product is also designed for IT power distribution system with phase-to-phase voltage 230V.
Обладнання відповідає вимогам Технічного регламенту обмеження використання деяких небезпечних
речовин в електричному та електронному обладнанні.
Angle of tilt
If you use the projector tilted at an angle of more than 10°, it could be
damaged or cause an accident.
ESC/VP21 Commands
Use of ESC/VP21 enables control of the projector from an external device. For more details, see the following
Web site.
http://www.epson.com
RS-232C Cable layouts
• Connector shape: D-sub 9-pin (male)
• Projector input port name: RS-232C
• Signal name:
Signal Name
Function
GND
Signal wire ground
TD
Transmit data
RD
Receive data
<At the projector>
<At the projector>
<At the computer>
(PC serial cable)
114
<At the computer>
Appendix
• Communications protocol
Default baud rate setting: 9600 bps
Data length: 8 bit
Parity: None
Stop-bit: 1 bit
Flow control: None
Indication of the manufacturer and the importer in accordance with requirements of directive 2011/65/
EU (RoHS)
Manufacturer: SEIKO EPSON CORPORATION
Address: 3-5, Owa 3-chome, Suwa-shi, Nagano-ken 392-8502 Japan
Telephone: 81-266-52-3131
Importer: SEIKO EUROPE B.V.
Address: Azië building, Atlas ArenA, Hoogoorddreef 5, 1101 BA Amsterdam Zuidoost The Netherlands
Telephone: 31-20-314-5000
115
Appendix
DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B Personal Computers
We:
Located at:
Tel:
Epson America, Inc.
3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
562-981-3840
Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the
FCC rules as a Class B digital device. Each product marketed, is identical to the representative unit tested and
found to be compliant with the standards. Records maintained continue to reflect the equipment being
produced can be expected to be within the variation accepted, due to quantity production and testing on a
statistical basis as required by 47CFR 2.909. Operation is subject to the following two conditions : (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Trade Name:
EPSON
Type of Product:
LCD Projector
Model:
H651C/H652C/H653C
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures.
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC
Certification or Declaration of this device and may cause interference levels which exceed the limits
established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded
equipment interface cable with this device. If this equipment has more than one interface connector, do not
leave cables connected to unused interfaces. Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
116
Appendix
Glossary
This section briefly explains the difficult terms that are not explained in context in the text of this guide. For
details, refer to other commercially available publications.
HDCP
HDMI
™
HDCP is an abbreviation for High-bandwidth Digital Content Protection. It is used to pre‐
vent illegal copying and protect copyrights by encrypting digital signals sent over DVI and
HDMI ports. Because the HDMI port on this projector supports HDCP, it can project digital
images protected by HDCP technology. However, the projector may not be able to project
images protected with updated or revised versions of HDCP encryption.
An abbreviation for High Definition Multimedia Interface. This is the standard by which
HD images and multichannel audio signals are digitally transmitted.
™
HDMI is a standard aimed at digital consumer electronics and computers. By not com‐
pressing the digital signal, the image can be transferred at the highest quality possible. It
also provides an encryption function for the digital signal.
HDTV
An abbreviation for High-Definition Television. This refers to high-definition systems
which satisfy the following conditions.
• Vertical resolution of 720p or 1080i or greater (p = Progressive, i = Interlace)
• Screen aspect of 16:9 Dolby Digital audio reception and playback (or output)
MHL
An abbreviation for Mobile High-definition Link, which is a standard high-definition in‐
terface that enables high-speed transfer of video signals on mobile devices.
It is a standard targeting smartphones and tablets that transfers uncompressed digital
signals without loss of quality and also enables simultaneous charging of such devices.
NTSC
An abbreviation for the National Television Standards Committee. A terrestrial analog
color broadcasting method. This method is used in Japan, North America, and Latin Amer‐
ica.
PAL
An abbreviation for Phase Alternation by Line. A terrestrial analog color broadcasting
method. This method is used in various Western European countries (with the exception
of France), Asian countries such as China, and Africa.
SDTV
An abbreviation for Standard Definition Television. This refers to standard television sys‐
tems which do not satisfy the conditions for HDTV High-Definition Television.
SECAM
An abbreviation for SEquential Couleur A Memoire. A terrestrial analog color broadcasting
method. This method is used in France, Eastern Europe, the former Soviet Union, the
Middle East, Africa, and so on.
SVGA
A screen size standard with a resolution of 800 (horizontal) x 600 (vertical) dots.
SXGA
A screen size standard with a resolution of 1,280 (horizontal) x 1,024 (vertical) dots.
VGA
A screen size standard with a resolution of 640 (horizontal) x 480 (vertical) dots.
XGA
A screen size standard with a resolution of 1,024 (horizontal) x 768 (vertical) dots.
YCbCr
In component image signals for SDTV, Y is the brightness, while Cb and Cr indicate the
color difference.
YPbPr
In component image signals for HDTV, Y is the brightness, while Pb and Pr indicate the
color difference.
Aspect Ratio
The ratio between an image's length and its height. Screens with a horizontal:vertical ratio
of 16:9, such as HDTV screens, are known as wide screens.
SDTV and general computer displays have an aspect ratio of 4:3.
117
Appendix
Interlace
Transmits information needed to create one screen by sending every other line, starting
from the top of the image and working down to the bottom. Images are more likely to
flicker because one frame is displayed every other line.
Pairing
Register devices in advance when connecting with Bluetooth devices to ensure mutual
communication.
118
Appendix
General Notes
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the
information contained herein. Neither is any liability assumed for damages resulting from the use of the infor‐
mation contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties
for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse,
or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options
or any consumable products other than those designated as Original Epson Products or Epson Approved Prod‐
ucts by Seiko Epson Corporation.
The contents of this guide may be changed or updated without further notice.
Illustrations in this guide and the actual projector may differ.
Restriction of Use
When this product is used for applications requiring high reliability/safety such as transportation devices related
to aviation, rail, marine, automotive etc.; disaster prevention devices; various safety devices etc; or functional/
precision devices etc, you should use this product only after giving consideration to including fail-safes and
redundancies into your design to maintain safety and total system reliability. Because this product was not
intended for use in applications requiring extremely high reliability/safety such as aerospace equipment, main
communication equipment, nuclear power control equipment, or medical equipment related to direct medical
care etc, please make your own judgment on this product’s suitability after a full evaluation.
General Notice
EPSON is a registered trademark, EXCEED YOUR VISION, ELPLP and their logos are registered trademarks or
trademarks of Seiko Epson Corporation.
HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing
LLC.
WirelessHD, WiHD, and the WiHD logo are trademarks or registered trademarks of WirelessHD LLC.
InstaPrevue and the InstaPrevue logo are the trademarks or registered trademarks of Silicon Image, Inc.
®
Bluetooth and the Bluetooth logo are the trademarks of Bluetooth SIG, Inc.
MHL and the MHL logo are a trademark, registered trademark or service mark of MHL, LLC in the United States
and/or other countries.
™ and WPA2™ are registered trademarks of Wi-Fi Allience.
WPA
App Store is a service mark of Apple Inc.
Google Play is a trademark of Google Inc.
All other trademarks are the property of their respective owners and used for identification purpose only.
©SEIKO EPSON CORPORATION 2014. All rights reserved.
119
Index
Connecting smartphones or tablets
......................................................................... 20, 21
Connecting USB devices ............................. 20
Connecting video equipment .................. 18
Connecting WirelessHD devices .............. 21
Connection Mode ......................................... 85
Contrast ............................................................ 75
Control panel ................................................ 6, 7
Control panel lock ......................................... 80
Cool-down ....................................................... 25
2
2D-to-3D Conversion ................................... 77
3
3D brightness .................................................
3D depth ...........................................................
3D display .........................................................
3D Format ........................................................
3D format .........................................................
3D Glasses ........................................................
3D Glasses charging port ...........................
3D images ........................................................
3D settings .......................................................
3D viewing notice .........................................
77
77
77
87
77
46
54
46
77
77
D
Deep color ........................................................ 87
Deinterlacing .................................................. 77
Detail Enhancement .............................. 39, 78
Device Connections .............................. 79, 80
Device connections ...................................... 60
DHCP .................................................................. 86
Diagonal Screen Size .................................... 77
Direct power on ............................................. 82
Display ............................................................... 83
Display Background ..................................... 83
Displaying the test pattern ........................ 27
A
Adjusting focus .............................................. 27
Adjusting RGB ................................................. 36
Adjusting the tilt ............................................ 28
Advanced .................................................. 76, 78
Air filter ........................................................... 102
Air filter cover ..................................... 102, 105
Air filter replacement period .................. 104
Appearance ..................................................... 12
Aspect ......................................................... 33, 77
Audio ................................................................. 79
Auto iris ...................................................... 39, 76
Auto setup ....................................................... 78
E
EPSON Super White ...................................... 76
Erase memory .......................................... 44, 84
Error/Warning indicators ............................ 89
Event ID ................................................... 87, 101
Exit Picture in Picture ................................... 88
B
F
Basic menu ....................................................... 85
Brightness .......................................... 35, 75, 76
Focus .................................................................. 94
Focus adjustment .......................................... 27
Focus ring .................................................... 6, 27
Full ...................................................................... 33
C
CEC standards ................................................. 68
Channel ............................................................. 85
Child lock .......................................................... 80
Cleaning the 3D Glasses ........................... 104
Cleaning the air filter ................................. 102
Cleaning the lens ........................................ 104
Cleaning the main unit ............................. 103
Color mode ............................................... 32, 75
Color Saturation ............................................. 75
Color Temp. ..................................................... 75
Component port ............................................ 18
Configuration menu ..................................... 74
Connecting ...................................................... 18
Connecting a computer .............................. 19
Connecting MHL compatible devices
......................................................................... 20, 21
G
Gain ............................................................. 36, 76
Gamma ....................................................... 35, 76
Gateway Address ........................................... 86
H
H/V-Keystone ........................................... 30, 79
HDMI Link ......................................................... 79
HDMI link .......................................................... 68
HDMI port ......................................................... 68
HDMI video range ......................................... 78
HDMI1 port ................................. 18, 19, 20, 21
HDMI2 port ............................................... 18, 19
High altitude mode ...................................... 82
120
Index
H-Keystone ...................................................... 79
Hue .............................................................. 35, 76
P
Pairing ............................................................... 47
Panel Alignment ............................................ 83
Passphrase ....................................................... 86
Pattern Color ................................................... 83
PC port ............................................................... 19
Picture in Picture .................................... 72, 88
Position ............................................................. 77
Power ................................................................. 25
Power consumption ..................................... 76
Power Off Link ................................................ 79
Power On Link ................................................ 79
Power supply .................................................. 24
Projection ......................................................... 81
Projection size ......................................... 15, 27
Projector Info .................................................. 87
I
Illumination .....................................................
Image .................................................................
Image menu ....................................................
Image processing ..........................................
Images ...............................................................
Indicators ..........................................................
Info menu .........................................................
Input signal ......................................................
Inverse 3D Glasses .........................................
Inverse audio ...................................................
IP Address .........................................................
IP address display ..........................................
IP Settings ........................................................
82
32
75
78
70
89
87
87
77
79
86
86
86
R
K
Refresh rate ...................................................... 87
Remote Control ................................................ 8
Remote control .............................................. 23
Rename memory .................................... 44, 84
Replacement periods for consumables
............................................................................. 104
Replacement time ...................................... 104
Replacing consumables ........................... 105
Replacing the air filter ............................... 105
Replacing the lamp .................................... 106
Reset .............................................. 76, 79, 80, 83
Reset all ............................................................. 87
Reset lamp hours ................................. 87, 108
Reset memory .......................................... 44, 87
Reset menu ............................................... 86, 87
Resolution ........................................................ 87
RGB ..................................................................... 76
RGBCMY ..................................................... 35, 76
Keystone distortion ...................................... 30
L
Lamp cover ............................................... 6, 106
Lamp cover fixing screw ........................... 106
Lamp hours ...................................................... 87
Lamp replacement period ....................... 104
Language ......................................................... 83
Link indicator .................................................. 54
Load memory ........................................... 44, 84
Lock setting ..................................................... 80
M
Memory function ...........................................
Memory menu ................................................
Menu ..................................................................
Messages ..........................................................
Motion detection ...........................................
43
84
74
83
77
S
Saturation .................................................. 35, 76
Save memory ........................................... 43, 84
Scan mode ....................................................... 87
Search Access Point ...................................... 85
Security ............................................................. 86
Security menu ................................................ 86
Select Color ...................................................... 83
Serial number ................................................. 87
Settings menu ................................................ 79
Setup level ....................................................... 78
Sharpness .................................................. 38, 75
Signal menu .................................................... 77
Skin Tone .......................................................... 75
Sleep mode ...................................................... 82
N
Network menu ............................................... 84
Noise .................................................................. 94
Noise reduction .............................................. 78
O
Offset .......................................................... 36, 76
Operating range ............................................ 23
Operating time ............................................ 108
Operation ......................................................... 82
Overscan ........................................................... 78
121
Index
Slideshow ......................................................... 70
Soft keyboard ................................................. 85
Source ......................................................... 25, 87
Specifications ............................................... 113
SSID .................................................................... 85
SSID Display ..................................................... 86
Standby Confirmation ................................. 83
Start Adjustments ......................................... 83
Startup Screen ................................................ 83
Status ................................................................. 87
Sub menu ......................................................... 74
Subnet Mask .................................................... 86
Sub-screen ....................................................... 67
Subscreen Position ....................................... 88
Subscreen Size ................................................ 88
Subscreen Source .......................................... 88
Super-resolution ............................................ 78
Supported resolutions .............................. 110
Swap Main/Sub .............................................. 88
Sync info ........................................................... 87
Sync. ................................................................... 77
Z
Zoom .................................................................. 33
Zoom adjustment ......................................... 27
Zoom ring ........................................................... 6
T
Tint ......................................................................
Top menu .........................................................
Tracking ............................................................
Transmission range ......................................
Trigger Out ......................................................
75
74
77
61
82
U
USB ..................................................................... 70
USB port ............................................................ 20
User button ...................................................... 81
V
Version .............................................................. 87
Video port ........................................................ 18
Video Reception ..................................... 60, 80
Video signal ..................................................... 87
Viewing area .................................................... 49
V-Keystone ....................................................... 79
Volume ....................................................... 31, 79
W
WiHD indicator ............................................... 54
WiHD Mode ..................................................... 80
Wireless LAN menu ....................................... 85
Wireless LAN Power ...................................... 85
WirelessHD ................................................ 54, 80
122
Download PDF