Avlite AV-OL-ILAB UM-R, AV-OL-FL810 UM-R Obstruction Light Installation & Service Manual
Below you will find brief information for Obstruction Light AV-OL-ILAB UM-R, Obstruction Light AV-OL-FL810 UM-R. The obstruction light is designed to comply with FAA L-810 and ICAO LIOL Type A & B requirements. It is available in universal AC (110-240VAC), uses a single LED for minimal power consumption and has adjustable intensity settings. This document provides information for installation, wiring, setup and operation.
Advertisement
Advertisement
AV-OL-ILAB-UM-R & AV-OL-FL810-UM-R
Universal AC Low Intensity Obstruction Light
Installation & Service Manual
Version 2.7
Version No.
1.0
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
Description
Manual launch
Various
Spec table update
Alarm relay update
Dip Switch Table
Update: Wind speed
Update: Intensity & Operation Mode Setting
Spec table
Spec Table & contact details
Date
Feb 2013
June 2013
August 2013
August 2013
September 2013
November 2013
September 2014
June 2015
February 2016
Approved
A. Groell
A. Groell
A. Groell
A. Groell
A. Groell
S. Turner
W. Evans
W. Evans
J. Dore
Universal AC Low Intensity Obstruction Light
Single Light Fixture
Table of Contents
Introduction ..........................................................................................Page 4
Technology ...........................................................................................Page 4
AV-OL-ILAB-UM-R & AV-OL-FL810-UM-R Models .............................Page 5
Safety Information ...............................................................................Page 9
Unpacking, Installation, Wiring & Setup .........................................Page 10
Unpacking .................................................................................Page 10
Installation & Wiring ..................................................................Page 10
Opening & Closing the Light Head ..........................Page 11
AC Power Connection .............................................Page 11
Operation & Setup ....................................................................Page 13
Intensity & Operation Mode Setting .........................Page 14
Alarm Relay Output .................................................Page 15
Maintenance & Servicing ..................................................................Page 16
Trouble Shooting ...............................................................................Page 17
Appendix ............................................................................................Page 18
Light Head Wiring Diagram.......................................................Page 18
Light Head Parts Diagram ........................................................Page 19
Product Order Codes ................................................................Page 20
Certifications & Compliance......................................................Page 21
Avlite Light Warranty .........................................................................Page 22
Latest products and information available at www.avlite.com
3
Universal AC Low Intensity Obstruction Light
Single Light Fixture
Introduction
Congratulations! By choosing to purchase an Avlite light, you have become the owner of one of the most advanced LED obstruction lights in the world.
Avlite Systems draws on more than 25 years experience in the design and manufacture of navigation aids, and particular care has been taken to ensure your light gives years of trouble free service.
As a commitment to producing the highest quality products for our customers, Avlite has been independently certified as complying with the requirements of ISO 9001:2008 quality management system.
By taking a few moments to browse through this booklet, you will become familiar with the versatility of your light, and be able to maximise its operating function.
Please remember to complete the Avlite warranty registration card accompanying your light.
Technology
Avlite Systems is a world-class solar lighting systems manufacturer with a proven reputation for rapid, innovative, and agile technology solutions designed specifically for defense, government, civil and humanitarian aid operations in the most remote, toughest environments.
Electronics
Avlite employs leading in-house electronic engineers in the design and development of software and related circuitry. All individual electronic components are sourced directly by Avlite procurement staff ensuring that only the highest quality components are used in our products.
LED Technology
All Avlite lights use the latest advancements in LED (Light Emitting Diode) technology as a light source.
The major advantage of LED’s over traditional light sources is well established in that they typically have an operational life in excess of 100,000 hours, resulting in substantial savings to maintenance and servicing costs.
Precision Construction
Commitment to investing in the design and construction of injection-moulded parts including optic lenses, light bases and a range of other components ensures that all Avlite products are of a consistent and superior quality.
Optical Performance
Avlite manufactures a range of aviation LED lenses moulded from multi-cavity dies. The company has superior in-house lens manufacturing capabilities to support outstanding optical performance.
Award-winning, Patented Technology
Several United States and Australian patent registrations are held on Avlite’s range of innovative designs, with other regional patents pending in Canada, United Kingdom and Europe.
Latest products and information available at www.avlite.com
4
Universal AC Low Intensity Obstruction Light
Single Light Fixture
AV-OL-ILAB-UM-R & AV-OL-FL810-UM-R
Models
This Avlite light fixture is a steady burning, low intensity LED obstruction light designed to comply with FAA L-810 and ICAO LIOL Type A & B requirements. The model can be used for marking obstacles which pose a threat to aircraft, such as telecommunication towers, wind turbines, buildings and other tall structures.
Avlite’s LED obstruction lights offer an ultra bright, energy efficient and cost effective lighting solution.
The light fixture is available in universal AC (110-240VAC). The advanced light optic uses a single LED for minimal power consumption. The corrosion resistant, polycarbonate lens is specifically designed for use with LEDs to maximize light intensity and uniformity.
The light fixture incorporates internal diagnostic checking and an alarm contact for remote monitoring. The alarm relay will be released whenever there is a problem e.g. no power, supply voltage too low, LED failure, etc. The alarm relay will remain energized during the day when operating normally.
The ICAO model has adjustable intensity settings to allow the user to easily toggle between 10cd (ICAO Type A) and 32cd (ICAO Type B) light intensities.
Latest products and information available at www.avlite.com
5
Single LED Optic
Automatic night operation
Universal AC Low Intensity Obstruction Light
Single Light Fixture
Combined visual & infrared for visibility to pilots using night vision
(optional)
Tough UV-stabilised
LEXAN® polycarbonate lens & light base
Easily installs to
¾ pipe thread
inch
121 (4.76”)
119 (4.69”)
Standard Model
Model shown with optional 1 inch pipe thread adaptor
121 (4.76”)
119 (4.69”)
Standard Model Model shown with optional
1 inch pipe thread adapter
Latest products and information available at www.avlite.com
6
Universal AC Low Intensity Obstruction Light
Single Light Fixture
Subject t
Specifications subject t
SPECIFICATIONS•* ICAO Type A & Type B LIOL Single Fixture
12–48 VDC 110–240 VAC
Light Characteristics
Light Source
Available colours
Peak Intensity (cd)†
Horizontal Output (degrees)
Vertical Divergence (degrees)
Reflector Type
Intensity Adjustments
Operation Mode Adjustment
LED Life Expectancy (hours)
Electrical Characteristics
Operating Voltage
As tested;
AV-OL-ILAB-12-R (Type A & Type B)
Red as standard. Other colours available on request, including IR
As tested;
AV-OL-ILAB-UM-R (Type A & Type B)
Red as standard. Other colours available on request, including IR
Complies with ICAO LIOLA & LIOLB:
2013
Complies with ICAO LIOLA & LIOLB:
2013
360 360 as per ICAO Type A/B specification as per ICAO Type A/B specification
Single LED Optic
User-adjustable between 10cd
& 32cd
User-adjustable between dusk-till-dawn & 24 hour operation
>100,000
Single LED Optic
User-adjustable between 10cd
& 32cd
User-adjustable between dusk-till-dawn & 24 hour operation
>100,000
12 – 48 VDC 110 – 240 VAC
Power (W)
Circuit Protection
Temperature Range
Physical Characteristics
Body Material
ICAO LIOL Type A @ 10cd Steady-on with relay energised: Pmax = 0.9
ICAO LIOL Type B @ 32cd Steady-on with relay energised: Pmax = 2.16
Integrated
-40 to 80°C
ICAO LIOL Type A @ 10cd Steady-on with relay energised: Pmax = 1.2
ICAO LIOL Type B @ 32cd Steady-on with relay energised: Pmax = 4
Smax = 10.6VA
Integrated
-40 to 80°C
Lens Material
Lens Diameter (mm/inches)
Lens Design
Mounting
Height (mm/inches)
Width (mm/inches)
Depth (mm/inches)
Mass (kg/lbs)
Product Life Expectancy
Environmental Factors
Humidity
Icing
LEXAN® Polycarbonate – UV stabilized
LEXAN® Polycarbonate – UV stabilized
100 / 3 7 /
8
Single LED Optic
Standard Model: ¾ inch pipe thread
Standard Model: 137 / 5½
121 / 4¾
121 / 4¾
0.4 / 7 /
8
12 years plus
0 to 100%, MIL-STD-810F
3.41kg per square cm /
48.5lbs per square inch
Up to 240kph / 150mph
LEXAN® Polycarbonate – UV stabilized
LEXAN® Polycarbonate – UV stabilized
100 / 3 7 /
8
Single LED Optic
Standard Model: ¾ inch pipe thread
Standard Model: 137 / 5½
121 / 4¾
121 / 4¾
0.4 / 7 /
8
12 years plus
Wind Speed
Certifications
CE
0 to 100%, MIL-STD-810F
3.41kg per square cm /
48.5lbs per square inch
Up to 240kph / 150mph
Quality Assurance
ICAO
Waterproof
Intellectual Property
Trademarks
Warranty *
Options Available
EN61000-6-3:2007
EN61000-6-1:2007
ISO9001:2008
Low Intensity Obstruction Light
Type A & B - 2013
IP68
AVLITE® is a registered trademark of Avlite Systems
5 year warranty
• Variety of solar/battery configurations
• GSM Cell-Phone Monitoring
• Dual visual/IR output
• IR LED
• RS422/485 communications port
• Threaded adaptor to fit one (1) inch pipe
EN61000-6-3:2007
EN61000-6-1:2007
ISO9001:2008
Low Intensity Obstruction Light
Type A & B - 2013
IP68
AVLITE® is a registered trademark of Avlite Systems
5 year warranty
• GSM Cell-Phone Monitoring
• Dual visual/IR output
• IR LED
• Threaded adaptor to fit one (1) inch pipe
Universal AC Low Intensity Obstruction Light
Single Light Fixture
Subject t
Specifications subject t
SPECIFICATIONS•* FAA L-810 LIOL Single Fixture
12–48 VDC 110–240 VAC
Light Characteristics
Light Source
Available colors
Peak Intensity (cd)†
Horizontal Output (degrees)
Vertical Divergence (degrees)
Reflector Type
Intensity Adjustments
Operation Mode Adjustment
As tested;
FAA: AV-OL-FL810-12-R LED
Red as standard. Other colors available on request, including IR
Complies with FAA L-810 obstruction lights
360
As per FAA L-810 obstruction light specification
Single LED Optic
32.5cd
User-adjustable between dusk-till-dawn & 24 hour operation
>100,000
As tested;
FAA: AV-OL-FL810-UM-R LED
Red as standard. Other colors available on request, including IR
Complies with FAA L-810 obstruction lights
360
As per FAA L-810 obstruction light specification
Single LED Optic
32.5cd
User-adjustable between dusk-till-dawn & 24 hour operation
>100,000 LED Life Expectancy (hours)
Electrical Characteristics
Operating Voltage
Power (W)
Circuit Protection
Temperature Range
Physical Characteristics
Body Material
12 – 48 VDC
FAA L-810 @ 32.5cd Steady-on with relay energized: Pmax = 1.44
Integrated
-40 to 80°C
110 – 240 VAC
FAA L-810 @ 32.5cd Steady-on with relay energized: Pmax = 2
Smax = 5.3VA
Integrated
-40 to 80°C
Lens Material
Lens Diameter (mm/inches)
Lens Design
Mounting
Height (mm/inches)
Width (mm/inches)
Depth (mm/inches)
Mass (kg/lbs)
Product Life Expectancy
Environmental Factors
Humidity
Icing
LEXAN® Polycarbonate – UV stabilized
LEXAN® Polycarbonate – UV stabilized
100 / 3 7 /
8
Single LED Optic
Standard Model: ¾ inch pipe thread
Standard Model: 137 / 5½
121 / 4¾
121 / 4¾
0.4 / 7 /
8
12 years plus
0 to 100%, MIL-STD-810F
3.41kg per square cm /
48.5lbs per square inch
Up to 240kph / 150mph
LEXAN® Polycarbonate – UV stabilized
LEXAN® Polycarbonate – UV stabilized
100 / 3 7 /
8
Single LED Optic
Standard Model: ¾ inch pipe thread
Standard Model: 137 / 5½
121 / 4¾
121 / 4¾
0.4 / 7 /
8
12 years plus
Wind Speed
Certifications
CE
0 to 100%, MIL-STD-810F
3.41kg per square cm /
48.5lbs per square inch
Up to 240kph / 150mph
Quality Assurance
FAA
EN61000-6-3:2007
EN61000-6-1:2007
ISO9001:2008
L-810 Steady-burning Red
Obstruction Light
(Qualified by Intertek)
IP68
EN61000-6-3:2007
EN61000-6-1:2007
ISO9001:2008
L-810 Steady-burning Red
Obstruction Light
(Qualified by Intertek)
IP68 Waterproof
Intellectual Property
Trademarks
Warranty *
Options Available
AVLITE® is a registered trademark of Avlite Systems
5 year warranty
• Variety of solar/battery configurations
• GSM Cell-Phone Monitoring
• Dual visual/IR output
• IR LED
• RS422/485 communications port
• Threaded adaptor to fit one (1) inch pipe
AVLITE® is a registered trademark of Avlite Systems
5 year warranty
• GSM Cell-Phone Monitoring
• Dual visual/IR output
• IR LED
• Threaded adaptor to fit one (1) inch pipe
Universal AC Low Intensity Obstruction Light
Single Light Fixture
Safety Information
• Install the light in compliance with the effective local electrical code(s).
• Mains power should always be disconnected when work is being done in close proximity to electrical fittings, and electrical work should only be done by a licensed electrician.
• Operate the light only within the indicated electrical ratings and product usage instructions.
• To ensure that the light and peripheral equipment function safely and correctly, use cable in compliance with the effective local electrical code.
• Do not stare at the LED or shine the LED into your eyes or those of another person.
• Do dispose of the product according to the local laws and regulations for your region, for example, at a recycling center that accepts electronic devices.
Latest products and information available at www.avlite.com
9
Universal AC Low Intensity Obstruction Light
Single Light Fixture
Unpacking, Installation, Wiring & Setup
Unpacking
Unpack all hardware and inspect for damage. If there is any damage, please contact your Avlite Office.
Retain original packing material for possible future use in shipping.
Installation & Wiring
Before proceeding with installation or service, make sure the following conditions are met:
• Ensure the tower or mast is grounded (NO RF HAZARD)
• Check the mast lighting circuit is not faulty
• Ensure power lines are not ‘live’ (NO ELECTRICAL HAZARD)
• Avoid touching live circuits!
• Avoid touching any component or any part of the circuitry while the unit is operating. Do not change components or make adjustments inside the unit with power on.
Open the Obstruction Light as described. Guide the cable through the cable gland and mount the bottom half of the Obstruction Light on a mounting pole using the inner thread.
NOTE:
• Make sure the mounting pole is vertically aligned to guarantee the required beam pattern of the obstruction light
• Make sure the light’s beam pattern is not disturbed by any nearby obstacles
Shorten the cable and close/seal the cable gland.
With the unit open, observe the rear of the PCB mounted in the top half of the Obstruction Light for terminal blocks and switch settings.
NOTE: Use cable in compliance with the effective local electrical code. The cable outer diameter should be between 5mm and 10mm.
NOTE: There is no requirement to terminate the relay and/or the serial communication if not used.
Latest products and information available at www.avlite.com
10
Universal AC Low Intensity Obstruction Light
Single Light Fixture
OPENING & CLOSING THE LIGHT HEAD
• Remove the locking screw
• In order to open the unit, the top half of the unit should be turned anti-clockwise with respect to the bottom half. The top half will turn approximately 20mm over a positive “click” before separating from the bottom half. Attention should be paid to the restriction caused by the internal cabling which is secured by a cable gland.
• The unit is closed by reversing the above procedure, ensuring the black rubber O-ring remains in place.
Figure 1. Obstruction Light
Locking Screw
AC POWER CONNECTION (BLACK TERMINAL)
The unit is designed to operate from a nominal AC voltage from 110VAC-240VAC.
Wired as follows (according to Australian Standard):
• L1 (brown) = Line/Active
• L2 (blue) = Neutral
For location details of the terminals please refer to Figure 3.
Latest products and information available at www.avlite.com
11
J1
POWER
1 2 3
J2
ALARM
4 5 6
Universal AC Low Intensity Obstruction Light
Single Light Fixture
NO.
1
2
3
4
5
6
CONNECTOR
110-240VAC
110-240VAC
110-240VAC
ALARM
ALARM
ALARM
SIGNAL
L1 - LINE
NC
L2 - NEUT
COMM
NO
NC
Figure 2. Light wiring diagram and pinning
100-240
VAC
L1
LINE
NC
L2
NEUT
ALARM
1 2
SPST
Intensity switch
Figure 3. AC Obstruction Light PCB with terminals and DIP switches
Latest products and information available at www.avlite.com
12
Universal AC Low Intensity Obstruction Light
Single Light Fixture
Operation & Setup
When powered up, the light will constantly check day/night status using its internal ambient light sensor. The ambient light sensor averages its measurement for 30 seconds.
FAA: By default the lights turn ON when the ambient light decreases to not less than 35 footcandles (367.7 lux) and turn OFF when the ambient light decreases to not more than 60 footcandles (645.8 lux). These limits can be factory adjusted, if required.
ICAO: By default the lights turn ON when the ambient light decreases to not less than 35 footcandles (100 lux) and turn OFF when the ambient light decreases to not more than 60 footcandles (150 lux). These limits can be factory adjusted, if required.
If the light detects a LED failure the alarm relay can be used to provide a feedback to the user.
Latest products and information available at www.avlite.com
13
Universal AC Low Intensity Obstruction Light
Single Light Fixture
INTENSITY & OPERATION MODE SETTING
Light intensity & operation mode setting for ICAO compliant light fixture
The fixture will be supplied with the ICAO compliant optic.
The obstruction light will be pre-set to the intensity setting specified by the customer (ICAO Type A or
ICAO Type B) for a red steady burning Low Intensity Obstruction Light in dusk-till-dawn mode. The intensity and operation mode is pre-set in the factory and does not need to be set by the user.
If the customer should need to change the intensity or operation mode settings of the ICAO compliant model they can do this by changing the INTENSITY DIP switch. Please refer to table below for DIP switch settings and Figure 2 for circuit board location.
Position 2
OFF
OFF
ON
ON
Position 1 Light Intensity
OFF ICAO Low Intensity Obstruction Light Type A (10cd), dusk-till-dawn mode
– DEFAULT
ON ICAO Low Intensity Obstruction Light Type A (10cd), 24 hour mode
OFF
ON
ICAO Low Intensity Obstruction Light Type B (32cd), dusk-till-dawn mode
ICAO Low Intensity Obstruction Light Type B (32cd), 24 hour mode
Light intensity & operation mode setting for FAA compliant light fixture
The fixture will be supplied with the FAA compliant optic.
The FAA compliant model comes pre-set to the correct intensity for L-810 steady burning red obstruction light in dusk-till-dawn mode. The intensity and operation mode is pre-set in the factory and does not need to be set by the user.
If the customer should need to change the operation mode settings of the FAA compliant model they can do this by changing the INTENSITY DIP switch. Please refer to table below for DIP switch settings and
Figure 2 for circuit board location.
Position 2
No function
No function
Position 1
OFF
ON
Light Intensity
FAA L-810 Low Intensity Obstruction Light, dusk-till-dawn mode
– DEFAULT
FAA L-810 Low Intensity Obstruction Light, 24 hour mode
NOTE:
The ICAO Model and FAA Model have their own unique optic. The ICAO model cannot be used for
FAA purposes and the FAA model cannot be used for ICAO purposes. The model required needs to be specified at the time of order.
NOTE:
The unit must be installed by a qualified electrician.
Latest products and information available at www.avlite.com
14
Universal AC Low Intensity Obstruction Light
Single Light Fixture
ALARM RELAY OUTPUT
In normal operation the relay is energised
• Terminal contacts COMM and NC of the relay are electrically closed
• Terminal contacts COMM and NO of the relay are electrically open
Whenever the LED is not lit due to a power failure and/or a LED failure the relay will not be energised.
• Terminal contacts COMM and NO of the relay are electrically closed
• Terminal contacts COMM and NC of the relay are electrically open
For location details of the terminals please refer to Figure 2.
The alarm relay comes configured as follows:
• Relay normal operation (default, as described above)
The following alarm relay configurations are available as a special order. These must be specified at the time of order:
• Relay inverse operation (inverse functionality of the normal operation, used to conserve power)
• Relay disable (in case the relay is not required, used to conserve power)
NOTE: The alarm relay is intended for low voltage (SELV) connection only.
NOT FOR MAINS CONNECTION
Latest products and information available at www.avlite.com
15
Universal AC Low Intensity Obstruction Light
Single Light Fixture
Maintenance & Servicing
Designed to be maintenance free the Obstruction Lights requires minimal attention, though the following maintenance and servicing information is provided to help ensure the life of your Avlite product.
• Occasional cleaning of the dome lens may be required using a cloth and warm soapy water.
Latest products and information available at www.avlite.com
16
Problem
Light will not activate.
Universal AC Low Intensity Obstruction Light
Single Light Fixture
Trouble Shooting
Remedy
• Ensure proper connectivity with power supply
• Ensure that the power supply has the right polarity and voltage range
• Cover the light sensor to force the light ON
Latest products and information available at www.avlite.com
17
Universal AC Low Intensity Obstruction Light
Single Light Fixture
Appendix
Light Head Wiring Diagram
LED driver
Obstruction Light Head (top)
LED uP
AC/DC
J1
POWER
1 2 3
J2
ALARM
4 5 6
Light in normal operation
4
5
6
NO.
1
2
3
CONNECTOR
110-240VAC
110-240VAC
110-240VAC
ALARM
ALARM
ALARM
SIGNAL
L1 - LINE
NC
L2 - NEUT
COMM
NO
NC
Figure 4. Light head wiring diagram
Latest products and information available at www.avlite.com
18
Figure 5. Light head parts diagram
Universal AC Low Intensity Obstruction Light
Single Light Fixture
Light Head Parts Diagram
dome lens
Screw
Security lock optics
PCB with single LED
Top enclosure vent
Figure 5. Light head parts diagram
O-ring
Bottom enclosure
Cable gland
Metal ring
Inside thread for pole mounting
Latest products and information available at www.avlite.com
19
Universal AC Low Intensity Obstruction Light
Single Light Fixture
Product Order Codes
HOW TO ORDER AV-OL Series Obstruction Lights:
ICAO Compliant
AV-OL-ILAB-[Model]-[Color]-[?]-[?]-[?]-[?]-[?]
Product No.:
Model:
12 = 12–48 VDC
UM = 110–240 VAC
Color:
R = Red
IR = Infrared
RIR = Combined Red/IR
Single or Dual Fixture:
[blank] = Single light fixture
[D] = Dual light fixture
Solar/Battery Configuration:
CT1 = Type 1
CT2 = Type 2
[blank] = No solar/battery configuration
Monitoring & Control:
G = GSM
RF = Radio Control
[blank] = No monitoring & control
RS Communications Port (12-48VDC Model only):
RS = RS communications port
[blank] = No RS communications port
Feature:
0 = Both lights activated at the same time
1 = One light activated with automatic changeover ability
[blank] = No feature
FAA Compliant
AV-OL-FL810-[Model]-[Color]-[?]-[?]-[?]-[?]-[?]
Product No.:
Model:
12 = 12–48 VDC
UM = 110–240 VAC
Color:
R = Red
IR = Infrared
RIR = Combined Red/IR
Single or Dual Fixture:
[blank] = Single light fixture
[D] = Dual light fixture
Solar/Battery Configuration:
CT1 = Type 1
CT2 = Type 2
[blank] = No solar/battery configuration
Monitoring & Control:
G = GSM
RF = Radio Control
[blank] = No monitoring & control
RS Communications Port (12-48VDC Model only):
RS = RS communications port
[blank] = No RS communications port
Feature:
0 = Both lights activated at the same time
1 = One light activated with automatic changeover ability
[blank] = No feature
Latest products and information available at www.avlite.com
20
Universal AC Low Intensity Obstruction Light
Single Light Fixture
Certifications & Compliance
Certified to: FAA AC NO: 150/5345-43G L-810 (L)
FAA Engineering Brief No. 67
Compliant to: Low Intensity Type A & B Obstruction Light, ICAO Annex 14, Volume 1, Sixth Edition, July
2013, ‘Aerodrome Design and Operations
Latest products and information available at www.avlite.com
21
Universal AC Low Intensity Obstruction Light
Single Light Fixture
Avlite Light Warranty V1.3
Activating the Warranty
Upon purchase, the Avlite Systems warranty must be activated for recognition of future claims. To do this you need to register on-line. Please complete the Online Registration Form at:
www.avlite.com
Avlite Systems will repair or replace your lantern in the event of electronic failure for a period of up to three years from the date of purchase.
Avlite Systems will repair or replace any ancillary or accessory products in the event of failure for a period of up to one year from the date of purchase, as per the terms & conditions below.
The unit must be returned to Avlite freight prepaid.
Warranty Terms
1. Avlite Systems warrants that any Avlite aviation products fitted with telemetry equipment including but not limited to AIS, GSM, GPS or RF (“Telemetry Products”) will be free from defective materials and workmanship under normal and intended use, subject to the conditions hereinafter set forth, for a period of twelve (12) months from the date of purchase by the original purchaser.
2. Avlite Systems warrants that any rotationally-moulded products (“Roto-Moulded Products”) and accessory products (“Accessory Products”) will be free from defective materials and workmanship under normal and intended use, subject to the conditions hereinafter set forth, for a period of twelve (12) months from the date of purchase by the original purchaser.
3. Avlite Systems warrants that any Avlite aviation products other than the Telemetry Products, Roto-
Moulded Products and Accessory Products (“Avlite Products”) will be free from defective materials and workmanship under normal and intended use, subject to the conditions hereinafter set forth, for a period of three (3) years from the date of purchase by the original purchaser.
4. Avlite Systems warrants that any Avlite obstruction products other than the Telemetry Products,
Roto-Moulded Products and Accessory Products (“Avlite Products”) will be free from defective materials and workmanship under normal and intended use, subject to the conditions hereinafter set forth, for a period of five (5) years from the date of purchase by the original purchaser.
5. Avlite Systems will repair or replace, at Avlite’s sole discretion, any Telemetry Products, Roto-
Moulded Products, Accessory Products or Avlite Products found to be defective in material and workmanship in the relevant warranty period so long as the Warranty Conditions (set out below) are satisfied.
6. If any Telemetry Products or Avlite Products are fitted with a rechargeable battery, Avlite Systems warrants the battery will be free from defect for a period of one (1) year when used within original manufacturer’s specifications and instructions.
Warranty Conditions
This Warranty is subject to the following conditions and limitations;
1. The warranty is applicable to lanterns manufactured from 1/1/2009.
2. The warranty is void and inapplicable if: a. the product has been used or handled other than in accordance with the instructions in the owner’s manual and any other information or instructions provided to the customer by Avlite; b. the product has been deliberately abused, or misused, damaged by accident or neglect or in being transported; or c. the defect is due to the product being repaired or tampered with by anyone other than Avlite or authorised Avlite repair personnel.
3. The customer must give Avlite Systems notice of any defect with the product within 30 days of the customer becoming aware of the defect.
4. Rechargeable batteries have a limited number of charge cycles and may eventually need to be replaced. Typical battery replacement period is 3-4 years. Long term exposure to high temperatures will shorten the battery life. Batteries used or stored in a manner inconsistent with
Latest products and information available at www.avlite.com
22
Universal AC Low Intensity Obstruction Light
Single Light Fixture
the manufacturer’s specifications and instructions shall not be covered by this warranty.
5. No modifications to the original specifications determined by Avlite shall be made without written approval of Avlite Systems.
6. Avlite lights can be fitted with 3rd party power supplies and accessories but are covered by the 3rd party warranty terms and conditions.
7. The product must be packed and returned to Avlite Systems by the customer at his or her sole expense. Avlite Systems will pay return freight of its choice. A returned product must be accompanied by a written description of the defect and a photocopy of the original purchase receipt. This receipt must clearly list model and serial number, the date of purchase, the name and address of the purchaser and authorised dealer and the price paid by the purchaser. On receipt of the product, Avlite Systems will assess the product and advise the customer as to whether the claimed defect is covered by this warranty.
8. Avlite Systems reserves the right to modify the design of any product without obligation to purchasers of previously manufactured products and to change the prices or specifications of any product without notice or obligation to any person.
9. Input voltage shall not exceed those recommended for the product.
10. Warranty does not cover damage caused by the incorrect replacement of battery in solar lantern models.
11. This warranty does not cover any damage or defect caused to any product as a result of water flooding or any other acts of nature.
12. There are no representations or warranties of any kind by Avlite or any other person who is an agent, employee, or other representative or affiliate of Avlite, express or implied, with respect to condition of performance of any product, their merchantability, or fitness for a particular purpose, or with respect to any other matter relating to any products.
Limitation of Liability
To the extent permitted by acts and regulations applicable in the country of manufacture, the liability of Avlite Systems under this Warranty will be, at the option of Avlite Systems, limited to either the replacement or repair of any defective product covered by this Warranty. Avlite Systems will not be liable to Buyer for consequential damages resulting from any defect or deficiencies in accepted items.
Limited to Original Purchaser
This Warranty is for the sole benefit of the original purchaser of the covered product and shall not extend to any subsequent purchaser of the product.
Miscellaneous
Apart from the specific warranties provided under this warranty, all other express or implied warranties relating to the above product is hereby excluded to the fullest extent allowable under law. The warranty does not extend to any lost profits, loss of good will or any indirect, incidental or consequential costs or damages or losses incurred by the purchaser as a result of any defect with the covered product.
Warrantor
Avlite Systems has authorised distribution in many countries of the world. In each country, the authorised importing distributor has accepted the responsibility for warranty of products sold by distributor. Warranty service should normally be obtained from the importing distributor from whom you purchased your product. In the event of service required beyond the capability of the importer,
Avlite Systems will fulfil the conditions of the warranty. Such product must be returned at the owner’s expense to the Avlite Systems factory, together with a photocopy of the bill of sale for that product, a detailed description of the problem, and any information necessary for return shipment.
Information in this manual is subject to change without notice and does not represent a commitment on the part of the vendor.
Sealite products are subject to certain Australian and worldwide patent applications.
Latest products and information available at www.avlite.com
23
Universal AC Low Intensity Obstruction Light
Single Light Fixture
Other Avlite Products Available
Solar Aviation Lighting Helipad Lighting
Obstruction Lighting
Typical Applications
• Temporary & permanent airfield lighting
• Remote, emergency & defence airfield lighting
• Barricade, hazard & perimeter lighting
• Helipad lighting
• Obstruction lighting
For a complete list of product compliances including ICAO & FAA, please contact Avlite today
Airfield Markers
& Accessories
Portable Airfield Lighting
System
AUSTRALIA t: +61 (0)3 5977 6128
USA t: +1 (603) 737 1310
UNITED KINGDOM t: +44 (0) 1502 588026
A subsidiary of Sealite Pty Ltd www.sealite.com
e: [email protected]
We believe technology improves navigation™

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Compliant with FAA L-810 & ICAO LIOL Type A & B
- Universal AC (110-240VAC)
- Single LED for minimal power consumption
- Adjustable intensity settings
- Internal diagnostics and alarm contact for remote monitoring