Product Number 8800/8810
Owner’s and Service Manual
Strength Systems
Part Number 8800-999-4 E
www.cybexinternational.com
Product Number 8800/8810
Owner’s and Service Manual
Strength Systems
Part Number 8800-999-4 E
Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc.
DISCLAIMER: Cybex International, Inc., makes no representations or warranties regarding the contents of this manual. We reserve the right to
revise this document at any time or to make changes to the product described within it without notice or obligation to notify any person of such
revisions or changes.
© Copyright 2010, Cybex International, Inc. All rights reserved.
Printed in the United States of America.
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183
www.cybexinternational.com • techhelp@cybexintl.com • 8800-999-4 E • March 2010
Table of Contents
1 Safety
Safety . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Safety Guidelines and Practices. . . . . . . 1-2
Warning/Caution Decals . . . . . . . . . . 1-3
Regular Maintenance Activities . . . . . 1-5
Using Proper Form . . . . . . . . . . . . . . 1-5
2 Exercises
Intended Use. . . . . . . . . . . . . . . . . . . 2-1
Instructions. . . . . . . . . . . . . . . . . . . 2-2
3 Customer Service
Contacting Service . . . . . . . . . . . . . .
Ordering parts . . . . . . . . . . . . . . . . . .
Return Material Authorization (RMA).
Damaged Parts . . . . . . . . . . . . . . . . .
3-1
3-1
3-2
3-2
4 Assembly . . . . . . . . . . . . . . . . . . . . . 4-1
5 Maintenance
Daily Procedures . . . . . . . . . . . . . . . .
Weekly Procedures . . . . . . . . . . . . . .
Yearly Procedures . . . . . . . . . . . . . . .
Cable Adjustment . . . . . . . . . . . . . .
Environment. . . . . . . . . . . . . . . . . . .
Storage . . . . . . . . . . . . . . . . . . . . . .
5-1
5-4
5-5
5-6
5-7
5-7
6 Service . . . . . . . . . . . . . . . . . . . . . . . 6-1
Page i
Cybex Product Number 8800/8810 Owner’s Manual
1 - Safety
Safety
Read the Owner’s Manual carefully before assembling, servicing or using the equipment.
It is the responsibility of the facility owner and/or owner of the equipment to instruct users on proper
operation of the equipment and review all labels.
WARNING: Serious injury could occur if these safety precautions are not observed:
User Safety Precautions
•
•
Obtain a medical exam prior to beginning an exercise program.
•
•
•
•
•
Keep body and clothing free from and clear of all moving parts.
•
Never pin the weights in an elevated position. DO NOT use the machine if found in this condition.
See assistance from floor staff.
•
•
•
•
Children must not be allowed near these machines. Teenagers must be supervised.
•
•
Read and understand warning labels and user manual prior to exercising. Obtain instruction
prior to use.
Inspect machine prior to use. DO NOT use if it appears damaged or inoperable.
DO NOT attempt to fix a broken or jammed machine. Notify floor staff.
Use the machine only for the intended use. DO NOT modify the machine.
Be sure that the weight pin is completely inserted. Use only the pin provided by the manufacturer.
If unsure seek assistance.
DO NOT use if guards are missing or damaged.
DO NOT lls or other incremental weights, except those provided by the manufacturer.
Inspect all cables and belts and connections prior to use. DO NOT use if any components are worn,
frayed or damaged.
DO NOT remove any labeling from equipment. Replace any damaged labels.
Stop exercising if you feel faint, dizzy or experience pain at any time while exercising and consult
your physician.
Facility Safety Precautions
•
•
Read the Owner’s Manual carefully before assembling, servicing or using the equipment.
Securely anchor each machine to the floor using the anchor holes provided in each machine.
NOTE: Cybex is not responsible for the actual anchoring of equipment. Consult with a
professional contractor.
NOTE: Use fasteners having a minimum of 500 lbs. tensile capacity (3/8” grade 2 bolts or
better).
NOTE: If legs/frame does not contact surface, DO NOT pull down with anchors. Shim any
leg or frame not in contact with surface using flat washers.
Safety
Page 1-1
Cybex Product Number 8800/8810 Owner’s Manual
•
Make sure that each machine is set up and operated on a solid level surface. Do not install
equipment on an uneven surface.
•
•
•
Make sure that all users are properly trained on how to use the equipment.
Make sure there is enough room for safe access and operation of the equipment.
Perform regular maintenance checks on the equipment. Also pay close attention to all areas most
susceptible to wear, including (but not limited to) cables, pulleys, belts and grips.
•
Immediately replace worn or damaged components. If unable to immediately replace worn or
damaged components then remove from service until the repair is made.
•
•
•
Use only Cybex supplied components to maintain/repair the equipment.
Keep a repair log of all maintenance activities.
Inspect all cables and belts and connections prior to use. DO NOT use if any components are worn,
frayed or damaged.
NOTE: It is the sole responsibility of the user/owner or facility operator to ensure that regular
maintenance is performed.
Safety Guidelines And Practices
Cybex recommends that all fitness equipment be used in a supervised area. It is recommended that the
equipment be located in an access controlled area. Control is the responsibility of the owner. The extent
of control is at the discretion of the owner.
It is the responsibility of the purchaser/user of Cybex products to read and understand the owner’s
manual, and warning labels; as well as instruct all individuals, whether end users or supervising
personnel, on proper usage of the equipment.
PROPER USAGE:
Use machine only as described in the manual. Failing to follow proper instructions may result in injury.
Do Not Lean Against or Pull On the framework, weight stack, or any component, whether machine is at
rest or in use. Inappropriate or improper use may result in injury to users or third parties (bystanders).
Do not use machine if it is not located on a solid level surface or is improperly installed.
Provide an adequate safety perimeter between the machine, walls and other equipment to ensure that
the facility has the proper clearance for usage and training.
SECURING EQUIPMENT:
The machine has holes in the feet, which allow for ease in anchoring to the floor. Cybex strongly
recommends that, to eliminate rocking, tipping or falling over due to incorrect usage and misuse,
equipment be secured to a solid, level surface.
1. The solid, level surface should not deviate more than 1/8” over a 10’ distance or as defined and
required by local building and architectural codes.
2. Anchoring of equipment must be completed by a qualified licensed contractor.
Safety
Page 1-2
Cybex Product Number 8800/8810 Owner’s Manual
3. Anchoring holes are provided on the feet of the frame. All anchoring locations must be used when
anchoring the equipment to the floor.
4. Due to the wide variation of flooring on which machines may be anchored or installed, verify
anchoring method and anchoring fasteners with a qualified and licensed contractor.
5. A minimum pull out force of 220 lbs/100 kgs is required for each anchor position..
6. Do not use machine until it is properly anchored.
MAINTENANCE:
Preventative maintenance allows proper equipment operation and reduces the risk of injury. Perform the
maintenance requirements as specified in the manual.
STANDARD COMPLIANCE:
Cybex products meet or exceed applicable ASTM and EN Standards.
Warning/Caution Decals
Warning decals indicate a potentially hazardous situation, which, if not avoided, could result in death or
serious injury.
Caution decals indicate a potentially hazardous situation, which, if not avoided, could result in minor or
moderate injury.
The warning and caution decals are shown on the following page. The diagrams following the decals
show where each decal is located.
Safety
Page 1-3
Cybex Product Number 8800/8810 Owner’s Manual
A
CAUTION
B
Failure to correctly
adjust could result in
personal injury.
Always fully engage
the detent pin before
use to avoid injury.
8500-025-4 A
C
CAUTION
Do not rest body
weight on stabilization
pad or arm.
Doing so may result
in personal injury.
8800-442-4 A
4605-381-4 A
Safety
Page 1-4
Cybex Product Number 8800/8810 Owner’s Manual
8800/8810
B
C
A
B
B
(both sides)
B
(both sides)
Description
Part No.
A. Warning Label....................4605-381-4
B. Caution Decal.....................8500-025-4
C. Caution Decal.....................8800-442-4
Safety
Page 1-5
Cybex Product Number 8800/8810 Owner’s Manual
Regular Maintenance Activities
Preventative maintenance activities must be performed to maintain normal operation of your equipment.
Keeping a log sheet of all maintenance actions will assist you in staying current with all preventative
maintenance activities. The preventative maintenance actions are described in detail in Chapter 5.
Briefly, they include:
Daily
1. Clean upholstery.
Weekly
1. Inspect all nuts and bolts for looseness. Tighten as required.
2. Inspect all cables and belts for damage or wear (see Chapter 5). If a cable or belt is worn
or damaged, immediately discontinue use until cable or belt has been replaced.
3. Check for worn handles, worn snap links, and worn warning labeling. Replace all worn parts
immediately.
4. Inspect for loose or worn grips. Replace all loose or worn grips immediately.
5
Inspect weight stacks for proper alignment and operation. Correct all improper alignment
and operation issues immediately.
6. Lubricate guide rods using automotive engine oil only.
Yearly
1. Replace all cables and belts at least annually.
Using Proper Form
Before working out, read and understand the exercises located on the placard and in Chapter 2.
Safety
Page 1-6
Product Number 8800/8810 Owner’s Manual
2 - Exercise
Intended Use
The intended use of this equipment is to aid or improve general physical fitness and exercise. For
Commercial use.
Instructions
Read and understand all instructions and warnings prior to using this machine. See Chapter 1, Safety, in
the Owner’s Manual or consult with floor staff.
• Select appropriate resistance.
• Adjust handles for proper pulley height.
• Rotate pulleys to desired angle.
• Adjust stabilization arm to desired angle.
• Adjust stabilization pad to desired position.
• Ensure all adjustment knobs are locked into place
NOTE: Position stabilization arm and pad all the way in and all the way down when not in use.
CHEST PRESS
SEATED PRESS
ROW
ARM CURL
Exercise
Page 2-1
Product Number 8800/8810 Owner’s Manual
ARM EXTENSION
SQUAT
HIP ADDUCTION
HIP EXTENSION-KNEE FLEXION
TRUNK EXTENSION
Exercise
Page 2-2
TRUNK ROTATION
HIP ABDUCTION
HIP FLEXION-KNEE EXTENSION
TRUNK FLEXION
Product Number 8800/8810 Owner’s Manual
3 - Customer Service
Contacting Service
Hours of phone service are Monday through Friday from 8:30 to 6:00 p.m. Eastern Standard Time.
For Cybex customers living in the USA, contact Cybex Customer Service at 888-462-9239.
For Cybex customers living outside the USA, contact Cybex Customer Service at 508-533-4300
or fax 508-533-5183.
Find information on the web at www.cybexintl.com or by e-mail at techhelp@cybexintl.com.
Ordering Parts
Fax orders to 508-533-5183. To speak with a customer service representative, call 888-462-9239 (for customers
living within the USA) or 508-533-4300 (for customers outside the USA). You may also
contact us through e-mail at techhelp@cybexintl.com
Having the following information ready when calling will assist our Cybex representatives in serving you.
•
•
Unit Serial Number
Product Name
The unit serial number and product name can be found on the serial number decal. See Chapter 6 for exact location of serial number decal.
•
•
Part Description
Part Number
Part descriptions and part numbers are located in Chapter 6 of this manual.
•
•
Shipping Address
Contact Name
In addition to your shipping address and contact name, your account number is helpful but not required.
Return Material Authorization (RMA)
The Return Material Authorization (RMA) system outlines the procedures to follow when returning material for
placement, repair or credit. The system assures that returned materials are properly handled and analyzed. Follow
the following procedures carefully.
Contact your authorized Cybex dealer on all warranty-related matters. Your local Cybex dealer will request a RMA
from Cybex, if applicable. Under no circumstances will defective parts or equipment be accepted by Cybex without
proper RMA and an Automated Return Service (ARS) label.
Customer
Service
Page 3-1
Product Number 8800/8810 Owner’s Manual
1. Call the Customer Service Hot Line listed above for the return of any item that is defective.
2. Provide the technician with a detailed description of the problem you are having or the defect in the
item you wish to return.
3. Provide the model and serial number of your Cybex equipment.
4. At Cybex’s discretion, the technician may request that you return the problem part(s) to Cybex for
evaluation and repair or replacement. The technician will assign you a RMA number and will send
you an ARS label. The ARS label and the RMA numbers must be clearly displayed on the outside
of the package that contains the item(s) to be returned. Include the description of the problem, the
serial number of the Cybex equipment and the name and address of the owner in the package
along with the part(s).
5. Forward the package through UPS to Cybex.
Attn: Customer Service Department
Cybex International, Inc.
1975 24th Ave SW
Owatonna, MN 55060
NOTE: Merchandise returned without an RMA number on the outside of the package or shipments sent
COD will not be accepted by the Cybex receiving department.
Damaged Parts
Materials damaged in shipment should not be returned for credit. Shipping damages are the responsibility
of the carrier (UPS, Federal Express, trucking companies, etc.)
Apparent Damage - Upon receipt of your shipment, check all items carefully. Any damage seen with a
visual check must be noted on the freight bill and signed by the carrier’s agent. Failure to do so will result
in the carriers refusal to honor your damage claim. The carrier will provide you with the required forms for
filing such claims.
Concealed Damage - Damage not seen with a visual check upon receipt of a shipment but notices later
must be reported to the carrier as soon as possible. Upon discovery of the damage, a written or phone
request to the carrier asking them to perform an inspection of the materials must be made within ten days
of the delivery date. Keep all shipping containers and packing materials as they will be needed in the inspection process. The carrier will provide you with an inspection report and the necessary forms for filing
a concealed damage claim. Concealed damage claim is the carrier’s responsibility.
Customer
Service
Page 3-2
Product Number 8800/8810 Owner’s Manual
4 - Assembly
Tools Required
•
•
•
•
•
•
7/32” Allen wrench
3/4” Socket
Hammer
3/16” Pin punch
9/16” Wrench
Loctite #242
NOTE: Two people will be required to perform this procedure.
NOTE: It is the responsibility of the facility owner/owner of the equipment to ensure that there is
appropriate clearance around each machine to allow for safe use and passage.
NOTE: Refer to Chapter 6 for reference diagrams.
1. Read and understand all instructions thoroughly before assembling this product.
2. Verify the appropriate configuration was received:
A. Correct color of machine.
B. Proper weight stack and weight stack decals.
C. Appropriate owner’s manual.
D. Warranty sheet.
E. Verify which machine was received 8800 (Chin-Up Bar Installed) or 8810 (With Chin-Up Bar).
3. Move to desired location.
NOTE: If machine is an 8800 and does not fit through doorway proceed to step 10.
NOTE: If machine is an 8810 and does not fit through doorway proceed to step 10J- 10P. Proceed to
step 13 to install Chin-Up Bar.
NOTE: If machine is an 8810 install Chin-Up Bar. Proceed to step 13 to install Chin-Up Bar.
4. Remove shipping pallet.
WARNING: Use extreme caution when removing shipping pallet.
Failure to do so could result in injury.
A. With an assistant, using a 9/16” wrench, carefully remove each lag bolt securing frame to
pallet.
B. Carefully place frame on floor.
Assembly
Page 4-1
Product Number 8800/8810 Owner’s Manual
5. Securely anchor machine to the floor.
A. Securely anchor machine to the floor using the anchor holes provided in each machine.
NOTE: Cybex is not responsible for the actual anchoring of equipment. Consult with a professional contractor.
NOTE: Use fasteners having a minimum of 500 lbs tensil capacity (3/8” grade 2 bolts or better).
NOTE: If legs/frame does not contact surface, DO NOT pull down with anchors. Shim any leg or frame not in
contact with surface using flat washers.
6. Install weight plates.
A. Using a 7/32” Allen wrench, remove the two Button Head Socket Cap Screws (BHSCS)
securing the top cap to the frame. See Figure 1.
BHSCS
Shroud
Top Cap
Figure 1
B. Remove top cap and BHSCS and set aside.
C. Carefully lift shroud up and out of machine.
D. Slide spring loaded guide rod cap down guide rod until cap is clear of frame. NOTE: Guide rod cap is
spring loaded.
E. Slowly release grasp
of guide rod cap.
See Figure 2. NOTE:
Guide rod cap contains a
compression spring
that will fly if grasp is
not released slowly.
F. Remove guide rod
cap and spring and
set aside.
Assembly
Page 4-2
Guide
Rod Cap
Guide
Rod Cap
Compression
Spring
Figure 2
Guide Rods
Compression
Spring
Product Number 8800/8810 Owner’s Manual
G. Repeat steps 6D - 6F for other guide rod.
H. Using a 3/16” pin punch and hammer, carefully remove roll pin securing cable end to top weight connector. See Figure 3.
Cable End
Top Weight
Connector
Roll Pin
Figure 3
I.
Carefully lean guide rods slightly outward. NOTE: Excessive pressure on guide rods may
damage lower guide rod caps.
J. Slide top weight up and out of machine and carefully set aside.
K. Have an assistant hold guide rods vertical.
L. Carefully align weight plates over guide rods and slowly lower each weight plate.
NOTE: When installing weight plates, position plates so wide edges of bushings face upward and narrow
edges of bushings face downward. See Figures 4a and 4b.
NG
T
EC
ORR
WRO
C
WIDE bushing
edge faces upward
Figure 4a
NARROW bushing edge
NOTE: The narrow bushing
edge must face downward.
Figure 4b
M. Repeat step 6L for each weight plate.
N. Carefully slide top weight (removed in step 6J) over guide rods.
7. Install weight plate decals.
Front
NOTE: You have the option to use pounds, kilograms or both.
Back
A. Slowly and carefully peel off back side of decal. See Figure 5.
NOTE: When peeling off back cover, make sure that the decals
remain attached to the front sticker.
Figure 5
B. Align holes in decal with appropriate holes in weight stack.
NOTE: Do not allow the adhesive to touch weight stack at this
time.
Assembly
Page 4-3
Product Number 8800/8810 Owner’s Manual
C. Insert a guide pin through each hole of the template. NOTE: A guide pin can be anything that fits
through the weight stack hole, such as a weight stack selector pin.
D. Carefully align decal and rub it onto weight plates.
E. Carefully remove front side, leaving decals adhering to weight plates. See Figure 6.
Guide
Rod
9.0
20
18.0
40
60
80
100
Weight
Stack
120
140
160
180
200
220
240
260
280
300
320
340
360
380
400
36.0
45.0
54.0
63.0
72.0
81.0
90.0
99.0
108.0
117.0
126.0
Kilograms
135.0
144.0
153.0
162.0
171.0
180.0
Pounds
Figure 6
8. Cable routing.
A. Verify cable is routed through top of pulley bracket and then route cable end to top weight
connector.
B. Pull cable tight and secure in place with roll pin removed in step 6H.
C. Place weight stack pin in each plate to verify proper installation.
D. Without selecting any resistance, lift top weight up and down (simulating normal operation).
E. Have an assistant verify that the cable is moving smoothly and is routed straight from the pulley
bracket to the top of the weight plate connector.
9. Install back shrouds.
A. Carefully place shrouds into position.
B. Secure top cap in place with the two BHSCS removed in step 6A.
10. Separate Frame for 8800 (If needed to fit thru doorway).
A. Remove shipping pallet (refer to step 4).
B. Locate insert plug. See Figure 7.
Assembly
Page 4-4
Product Number 8800/8810 Owner’s Manual
Chin-Up Bar
Insert
plug
Insert
plug
Figure 7
C. Remove insert plug to gain access to BHSCS securing Chin-Up Bar. See Figure 7. NOTE: 8810
is not shipped with Chin up bar (attached refer to step 13).
D. Repeat step 10C for insert plug on opposite side.
E. Locate BHSCS on top of frame near pulley. See Figure 8.
BHSCS
Locknut
BHSCS
Figure 8
F. Using a 7/32” Allen wrench remove two BHSCS securing Chin-Up
Bar
G. Using a 7/32” Allen wrench and socket remove two BHSCS securing Chin-Up Bar.
BHSCS
H. Repeat step 10E and 10F for opposite side
I.
Carefully remove Chin-Up Bar and set aside.
J. With an assistant remove 4 (of 8) BHSCS securing frame halves
See Figure 9.
K. Move to desired location.
L. Place both halves of frame together and tightly secure the four
BHSCS removed in step 10J.
M. Place a drop of 242 Loctite on BHSCS and threaded hole removed
in step 10J.
Figure 9
Assembly
Page 4-5
Product Number 8800/8810 Owner’s Manual
N. With an assistant secure Chin-Up Bar in place removed in step 10I.
O. Verify all BHSCS are securely tightened.
P. Insert plugs removed in step 10C for 8800 or from hardware pack for the 8810.
11. Install weight plates, decals, cable routing and, shroud assembly for 8800.
A. Refer to step 6A -9B for weight plates, decals, cable routing, and shroud assembly.
12. Separate Frame for 8810 (If needed to fit thru doorway.)
A. Remove shipping pallet refer to step 4.
B. Refer to steps 10J-10N
13. Install Chin Up Bar (8810 units only).
A. Locate Chin Up Bar and hardware.
B. With an assistant, align Chin Up Bar in place.
C. Place a drop of Loctite 242 on BHSCS from hardware bag and threaded holes.
D. Secure Chin Up Bar with hardware from hardware bag.
E. Verify all BHSCS are securely tightened.
F. Carefully slide top weight (removed in step 6J) over guide rods.
G. Insert plugs from hardware bag. NOTE: Refer to step 10B for location of plugs.
14. Install weight plates, decals, cable routing and shroud assembly for 8810.
A. Refer to step 6A -9B for weight plates, decals, cable routing, and shroud assembly.
15. Verify proper operation.
Assembly
Page 4-6
Product Number 8800/8810 Owner’s Manual
5 - Maintenance
All preventive maintenance activities must be performed on a regular basis. Performing routine
preventive maintenance actions can aid in providing safe, trouble-free operation of all Cybex Strength Systems
equipment.
NOTE: Cybex is not responsible for performing regular inspection and maintenance actions for your machines.
Instruct all personnel in equipment inspection and maintenance actions and also in accident
reporting/recording. Cybex phone representatives are available to answer any questions or concerns that
you may have.
NOTE: All inspections and
repairs must be performed by
trained service personnel only.
Cybex will void warranty if
non-Cybex replacement
parts are used.
Daily Procedures
1. Upholstery - Wipe down all upholstery as per the recommendations listed below for light soiling and more difficult
stains.
Light Soiling
•
•
A solution of 10% household liquid soap with warm water applied with a soft damp cloth.
If necessary, a solution of liquid cleanser and water applied with a soft bristle brush. Wipe away the residue
with a water dampened cloth.
Maintenance
Page 5-1
Product Number 8800/8810 Owner’s Manual
More Difficult Stains
•
Dampen a soft white cloth with a solution of 10% household bleach (sodium hypochlorite),
90% water. Rub gently. Rinse with a water dampened cloth to remove bleach concentration.
•
•
The same procedure can be used with full strength household bleach, if necessary.
Allow bleach to puddle on the affected area or apply with a soaked cloth for approximately
30 minutes. Rinse with a water dampened cloth to remove any remaining bleach concentration.
Alternative Method for Difficult Stains
•
Dampen a soft white cloth with rubbing alcohol and rub gently. Rinse with a water dampened cloth to
remove any remaining rubbing alcohol concentration.
NOTE: To restore luster, a light coat of spray furniture wax can be used. Apply for 30 seconds and follow with a
light buffing using a clean white cloth.
Please Review Carefully
When using strong cleaning agents such as rubbing alcohol or bleach, it is advisable to first test in an
inconspicuous area. Other cleaning agents may contain harsh or unknown solvents and are subject to formula
changes by the product manufacturer without notice. Should you desire to use other cleaning agents, carefully try
them in an inconspicuous area to determine potential damage to the material. Never use harsh solvents or
cleaners which are intended for industrial applications. To clean stained or soiled areas, a soft white cloth is
recommended. Avoid use of paper towels.
Cleaning products may be harmful/irritating to your skin, eyes, etc. Use protective gloves and eye protection. Do
not inhale or swallow any cleaning product. Protect surrounding area/clothing from exposure. Use in well
ventilated area. Follow all product manufacturer’s warnings. CYBEX and its vendors cannot be held responsible
for damage or injuries resulting from the use or misuse of cleaning products.
2. Frames - Wipe down all frames using a mild solution of warm water and car wash soap. Be sure to dry
thoroughly. AVOID acid or chlorine based cleaners and also cleaners containing abrasives as these could
scratch or damage the equipment.
3. Chrome - Clean chrome tubes, first using chrome polish and then using a car wax seal. Neutral cleaners with
a pH between 5.5 and 8.5 are recommended. Be sure to dry thoroughly. AVOID acid or chlorine based cleaners
and also cleaners containing abrasives as these could scratch or damage the equipment.
4. Guidelines for cleaning front panel:
•
•
•
•
•
•
•
Maintenance
Page 5-2
Use clean soft cloths or sponges for application of cleaners and again for washing and rinsing.
Follow up the application with warm water rinse.
Don’t use abrasives or high alkaline cleaners.
Don’t leave cleaners on for long periods, wash immediately.
Don’t apply cleaners in direct sunlight or at elevated temperatures.
Don’t use scrapers, squeegees or razors.
Don’t clean with gasoline.
Product Number 8800/8810 Owner’s Manual
Compatible Cleaners and Detergents:
•
•
•
•
•
Formula 409
Top Job
Joy
Palmolive
Windex with Ammonia D
To Minimize Fine or Hairline Scratches:
Mild automotive polish applied and removed with a soft, clean cloth will help fill scratches.
Suggested Polishes:
•
•
•
Johnson Past Wax
Mirror Glaze #10 Plastic Polish (by Mirror Bright Polish Co.)
Novus Plastics Polish #1, #2 (By Novus Inc.)
Maintenance
Page 5-3
Product Number 8800/8810 Owner’s Manual
Weekly Procedures
1. Check all nuts and bolts for looseness. Tighten as required.
2. Inspect all cables for wear or damage and proper tension. When inspecting cables, run fingers on the cable,
paying particular attention to bends in cable and attachment points.
WARNING: Replace all worn cables immediately. The following conditions may indicate a worn cable:
•
A tear or crack in the cable sheath that exposes the cable. See Figure 1.
Figure 1.
•
A kink in the cable. See Figure 2.
Figure 2.
•
A curled sheath. See Figure 3.
Figure 3.
•
“Necking”, a stretched cable sheath. See Figure 4.
Figure 4.
Maintenance
Page 5-4
Product Number 8800/8810 Owner’s Manual
3. Inspect bars and handles for wear, paying particular attention to tab area connection points.
Replace all worn handles immediately.
CAUTION: Replace all worn handles immediately. Do not use if less than 1/8” of material remains to the
edge. See Figure 5.
Attachment Hole
NOTE: Replace bar if less
than 1/8” of material
remains to the edge.
Figure 5
4. Inspect snap links for proper latching (indicates wear)
Replace all worn snap links immediately.
5. Inspect for loose or worn grips.
Replace all loose or worn grips immediately.
6. Inspect all labeling for readability. This includes instructional placards, warning and caution decals.
Replace all worn labeling immediately.
7. Inspect all weight stacks for proper alignment and operation.
Correct all improper alignment and operation issues immediately.
8. Wipe Weight Stack Guide Rods clean over entire length. Lubricate with a light coat of medium weight
automotive engine oil.
Yearly Procedures
1. Replace all cables at least annually.
Maintenance
Page 5-5
Product Number 8800/8810 Owner’s Manual
Cable Adjustment
Three types of cable tension adjustment are used on Cybex Strength Systems:
1. Jam Nut Adjustment - This type uses a jam nut
and a tension adjustment nut at the cable cam end
as the primary adjustment. The other end of the cable
usually contains a roll pin adjustment. See Figures 6 and 7.
2. Rod End Adjustment - This type of adjustment contains
a socket head cap screw (SHCS) securing a cable rod end
bearing to the machine. Primary
adjustment is by turning the rod end bearing. The other end
of the cable usually contains a roll pin cable adjustment.
See Figures 7 and 8.
Tension
Adjustment
Nut
Jam Nut
Figure 6
3. Roll Pin Adjustment - This type of adjustment utilizes a roll
pin and series of holes in the weight stack top weight
connector. See Figure 8.
Cable End
Frame
SHCS
Jam Nut
Cable Rod End
Bearing
Nylon
Locknut
Figure 7
Roll Pin
Cable End
Top Weight
Connector
Figure 8
Maintenance
Page 5-6
Product Number 8800/8810 Owner’s Manual
Environment
Humidity and Static Electricity
The unit is designed to function normally in an environment with a relative humidity range of 30% to 75%. The
unit can be shipped and stored in a relative humidity range of 10% to 90%.
Climatic dry air may cause static electricity. During workout, user may experience a shock due to build-up of
static electricity on the body and the discharge path of the unit. If static electricity is experienced, increase
humidity to a comfortable level through the use of a humidifier.
NOTE: Do not install or use the unit in an area of high humidity, such as in the vicinity of a steam room, sauna,
indoor pool or outdoors. Exposure to extensive water vapor, chlorine and/or bromine could adversely
affect parts of the machine.
Temperature - The unit is designed to function normally in an environment with an ambient temperature range
of 50 F (10 C) to 104 F(40 C) degrees.
o
o
o
o
Storage
Humidity - The unit can be shipped and stored in an environment with a relative humidity range of 10% to 90%.
NOTE: Do not store the unit in an area of high humidity, such as in the vicinity of a steam room, sauna, indoor
pool or outdoors. Exposure to extensive water vapor, chlorine and/or bromine could adversely affect the
electronics as well as other parts of the machine.
Temperature - The unit can be shipped and stored in an environment with an ambient temperature range of
32 F (0 C) and 140 F (60 C) degrees.
o
o
o
Maintenance
Page 5-7
Product Number 8800/8810 Owner’s Manual
This page intentionally left blank.
Maintenance
Page 5-8
Product Number 8800/8810 Owner’s Manual
6 - Service
Please refer to the next several pages for parts lists, exploded-view diagrams and cable
routing diagrams.
NOTE: All inspections
and repairs must be
performed by trained
service personnel only.
Cybex will void warranty if
non-Cybex replacement parts
are used.
Service
Page 6-1
Product Number 8800/8810 Owner’s Manual
This page intentionally left blank.
Service
Page 6-2
Product Number 8800/8810 Owner’s Manual
Functional Trainer
PRODUCT NO. 8800, 8810
R
S
S
Chin Up Bar for 8810
A
P
Q
B
E
D
E
J
J
E
(Both Sides)
I
E (Both Sides)
H T O
I
N
L
C
M
NOTE: See exploded-view diagram for location of F (cable Left Side), G (cable Right Side)
and K (serial number decal)
DESCRIPTION
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
DESCRIPTION
PART NO.
Placard Decal .................... 8800-598-x
Placard Decal .................... 8800-599-x
Warning Decal ................... 4605-381-x
Caution Decal..................... 8000-442-x
Caution Decal..................... 8500-025-x
Cable Left Side.................... 8800-002
Cable Right Side.................. 8800-003
Cushion Set/wear cover.......4800-404
Weight Selector Pin..............BH030207
Grip ................................... 4800-700
K.
L.
M.
N.
O.
P.
Q.
R.
S.
T.
PART NO.
Serial Number Decal
Rope Handle....................... 8800-433
Snap Link............................ GQ000206
Handle Assembly............... 8800-007
Handle Assembly............... 8800-008
Straight Handle Assembly.. 02203
Lat Bar Assembly.............. 8800-009
Grip ................................... 4605-514
Grip ................................... 4605-522
Wear Cover.......................... 4800-407
Service
Page 6-3
Product Number 8800/8810 Owner’s Manual
ITEM
QTY
1
2
3
4
1
1
02106
02203
08007
4
5
6
7
8
9
10
11
12
13
14
3
6
1
1
2
4
4
2
1
1
4
08229
11040-440
12040-357
12060-347
12090-322
12210-347
12210-348
13000-353
13000-354
13000-355
13000-364
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
2
2
2
18
8
1
2
2
2
1
1
2
2
1
2
2
2
1
1
1
1
2
1
1
1
1
2
2
2
1
1
2
2
4
4
2
2
1
2
1
2
4
4
2
16080-312
3900-434
3900-438
4400-354
4400-355
4505-331
4605-512
4800-263
4800-700
51122
51198
8800-002
8800-003
8800-009
8800-007
8800-008
8800-100
8800-200
8800-202
8800-203
8800-205
8800-206
8800-207
8800-208
8800-209
8800-212
8800-215
8800-216
8800-218
8800-223
8800-224
8800-333
8800-335
8800-339
8800-343
8800-350
8800-353
8800-388
8800-444
8800-433
BH030207
BR030206
BR030220
BR030223
59
60
61
62
6
4
1
4
BS070201
BS070208
CM000211
FB030255
Service
Page 6-4
PART NO.
DESCRIPTION
HALF WEIGHT PEG
STRAIGHT HANDLE ASSEMBLY
WASHER, NYLON .515 ID x 1.000
OD x .062 THK
PIN,DETENT
KNOB
PIN, DETENT
PIVOT PIN
FOOT PAD
GUIDE ROD CAP
GUIDE ROD CAP
FOOT PAD
FOOT PAD
FOOT PAD
BEARING, FLANGE .62 ID. x
.92 OD. x 1.75 LG
DETENT PIN
DECAL, CYBEX
DECAL, CYBEX
PULLEY
PULLEY
BUMPER, 1.50 DIA
INSERT PLASTIC, 7.94
C TOP WT 17-3X12
GRIP, 4.75 FOAM
ANKLE STRAP
WARRANTY BOOK (NOT SHOWN)
CABLE S/A LEFT SIDE
CABLE S/A RIGHT SIDE
LAT BAR ASSEMBLY
HANDLE ASSEMBLY
HANDLE ASSEMBLY
EDGE TRIM ASSEMBLY
FRAME
ADJUSTING HANDLE RH
WEIGHT FRAME RH
ADJUSTING HANDLE LH
PULLEY MOUNT
DETENT POST LH
CUSHION POST
ARM
WEIGHT FRAME LH
PIVOT
PULLEY SWIVEL
CAM BOLT
RACK
DETENT POST RH
FORMED WEIGHT CHANNEL
COUNTERWEIGHT
U-BUMPER
WT ROD .625 DIA X 69.38
FORMED GUIDE
MOLDED TOP CAP
DETENT PLATE
WEAR BLOCK
HANDLE, ROPE
PIN, WEIGHT SELECTOR
RING, RETAINING
RETAINING RING 1.250 INTERNAL
EXTERNAL RETAINING RING,
25 MM
COM SPRING .56 x .66 1.50 LG
COMPRESSION SPRING
DECAL, PATENT PENDING
BEARING RADIAL 25MM
ITEM
QTY
PART NO.
63
4
FB050226
64
2
FB130212
65
66
67
68
69
70
4
2
4
20
4
N/A
FC030010
GQ000206
HC620431
HC700417
HF700000
HM580410
71
72
73
74
75
76
77
78
79
6
4
6
42
2
4
2
2
4
HN625200
HN704000
HN704400
HN704901
HP286819
HS308300
HS347600
HS347700
HS720004
80
6
HT512517
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
NS
NS
NS
120
2
2
4
6
3
8
24
1
2
4
N/A
4
4
2
2
6
1
1
1
20
1
1
1
1
1
1
1
2
4
2
1
2
1
2
2
1
8
1
1
2
2
1
1
HW-60159
HX-60074
HT552511
JC620415
JC700412
JC700420
JC700424
JC702812
JS347400
PN660200
PP040004
PR060005
PR069400
PU060201
PW-60615
8500-025-X*
8800-442-X*
4800-404
4605-381-X*
HT552511
8800-351-9
8800-352-9
8800-599-X*
8800-598-X*
8800-382-9
8800-380-9
8800-230
4605-522
4605-550
PP130003
8810-101
4605-514
4800-407
JC782817
PP080230
8800-228
HF449063
8800-458
8800-459
4800-557
13000-551
8800-999-X*
11040-790
DESCRIPTION
BEARING,FLANGE 1.000 ID x 1.25 OD
x 1.00 LG
BUSHING, FLANGE .75 ID x .875
OD x .75 LG
TOLERANCE RING 1.457 ID
SNAP LINK
BHSCS .250-20 X 2.00
BHSCS .375-16 X 1.00
PANEL FASTNER, .375-16 , U TYPE
BHSCS .190 10-32 X .375
REMOVED 3/19/2010
LOCKNUT, .250-20 NYLON
HEX NUT .375-16
NUT, HEX JAM .375-16
LOCKNUT, .375-16 NYLON
SPIRAL PIN .188 X 1.12
SPLIT LOCKWASHER .250
WASHER, SAE .375
WASHER, USS .375
WASHER, FELT .641 ID X 1.250
OD X .125T
TAP SC 10-24 X 1.00 TYPE WB
PN HD PHIL BLK
WASHER, SHIM
RING, SNAP, EXTERNAL
SREW,TAP 8-16 X.38
BHSCS .250-20 X .75
BHSCS .375-16 X .50
BHSCS .375-16 X 1.25
BHSCS .375-16 X 1.75
SHCS .375-16 X .50
LOCKWASHER, INT TOOTH .375
INSERT, PLASTIC 1.00 DIA-11 GA
BALL STOP REMOVED 3/19/2010
BUMPER, WEIGHT
BUMPER, RECESS
BUMPER
PULLEY, CABLE, 2.00 OD x 1.0 HUB
DECAL, CAUTION
DECAL, CAUTION
CUSHION SET/W WEAR COVER
DECAL, WARNING
TAP SC 8-16X.38 BLK
FRONT PANEL (RIGHT SIDE)
BACK PANEL (RIGHT SIDE)
PLACARD
PLACARD
BACK PANEL (LEFT SIDE)
FRONT PANEL (LEFT SIDE)
CROSS TUBE
GRIP
PLUG .250-20
INSERT, PLASTIC
BAR, CHIN UP ASSEMBLY
GRIP
WEAR COVER
SHCS .500-13 X 1.00 BRT ZINC
PLASTIC INSERT
CHIN-UP BAR
INSERT, .75 X .250-20
PIVOT DECAL RIGHT HAND
PIVOT DECAL LEFT HAND
DECAL WT-PLATE (10-150)
DECAL WT-PLATE (160-200)
OPERATOR MANUAL
DECAL, MADE IN USA
Product Number 8800/8810 Owner’s Manual
RIGHT FRAME ASSEMBLY DETAIL
80
46
50
48
68
47
68
51
74
86
69
102
80
87
87
69
19
9
48
68
9
80
19
60
101
87
87
49
17
18
16
93
18
103
94
87
60
19
74
49
71
90
74
74
18
100
67
78
Qty 10
43
36
31
55
57
57
79
79
34
14
75
14
56
99
22
92
8
12
45
56
74
10
120
SEE
ADJUSTING
HANDLE ASSY
RIGHT SIDE
DETAIL
68
87
93
18
67
74
71
92
90
10
11
Service
Page 6-5
Product Number 8800/8810 Owner’s Manual
LEFT FRAME ASSEMBLY DETAIL
80
50
68
51
46
48
47
68
80
87
86
19
69
68
87
87
9
16
48
19
93
71
60
87
74
104
49
80
17
18
100
18
Qty 10
19
67
74
31
94
90
78
40
43
74
79
18
57
57
79
SEE
ADJUSTING
HANDLE ASSY
LEFT SIDE
DETAIL
14
55
75
74
90
56
8
68
93
74
56
13
18
105
36
14
92
67
37
87
22
92
10
71
11
10
106
Serial Number Detail
Service
Page 6-6
Product Number 8800/8810 Owner’s Manual
HANDLE AND PULLEY ASSEMBLY DETAIL
86
74
21
87
19
87
18
42
34
19
95
82
74
59
74
62
18
4
65
87
96
81
118
65
63
62
87
19
18
18
18
19
87
87
87
87
87
74
74
74
74
74
58
87
15
59
5
63
33
18
96
UPPER PULLEY ASSY
RIGHT SIDE DETAIL
23
74
5
41
45
ADJUSTING HANDLE ASSY
RIGHT SIDE DETAIL
ADJUSTING HANDLE ASSY
LEFT SIDE DETAIL
21
40
87
42
74
86
87
19
95
74
19
18
74
59
4
82
18
81
65
63
62
87
119
63
87
62
65
5
35
19
18
18
87
87
87
74
74
74
96
58
87
15
18
59
18
19
87
87
74
74
UPPER PULLEY ASSY
LEFT SIDE DETAIL
41
23
96
74
5
37
Service
Page 6-7
Product Number 8800/8810 Owner’s Manual
CABLE ASSEMBLY DETAIL
18
19
18
19
19
18
19
95
27
73
18
47
18
73
18
72
18
72
73
33
18
33
36
26
NOTE: LEFT SIDE CABLES
WILL ROUTE THE SAME WAY
AND SECURE TO 8800-205
CABLE ROUTING
(RIGHT SIDE SHOWN)
18
Service
Page 6-8
Product Number 8800/8810 Owner’s Manual
STABILIZATION ARM ASSEMBLY DETAIL
74
86
74
52
74
1
44
84
3
74
86
1
76
32
76
85
84
74
84
76
1
84
84
86
76
28
74
84
34
74
2
40
74
68
71
96
83
6
97
71
85
77
68
7
64
85
59
64
83
96
88
83
4
38
59
39
86
89
85
74
53
89
86
5
52
5
113
77
83
68
74
20 61
68 32
98
Service
Page 6-9
Product Number 8800/8810 Owner’s Manual
CROSS TUBE AND CHIN UP BAR DETAIL
8800 CROSS TUBE DETAIL
34
40
68
68
114
68
Torque to
1075-1125 in .lbs
107
74
74
90
68
90
68
116
37
45
115
115
8810 CHIN UP BAR DETAIL ( CHIN UP BAR ASSEMBLED IS PART NUMBER 8810-101 )
109
68
117
68
112
34
68
40
108
108
117
117
110
109
111
110
68
68
109
74
90
74
90
45
37
Service
Page 6-10
88±.25
18.43
PANEL CL
BACK PANEL LEFT SIDE DETAIL
9.21
39
ARM DECAL DETAIL
105
CENTER
ON PANEL
17
CENTER
ON PANEL
16
9.21
6.38
106
.67±.25
17
CENTER
ON PANEL
8.77±.25
2.27±.25
1.42 ±.25
104
96 CENTER ON TUBE
18.43
FRONT PANEL LEFT SIDE DETAIL
PANEL CL
PANEL CL
22.75 ±.25
97
18.43
BACK PANEL RIGHT SIDE DETAIL
9.21
96
99
2.75 ±.25
.67 ±.25
4.17±.25
39.25 ±.25
6.50 ±.25
102
31.88 ±.25
8.77±.25
2.27±.25
PANEL CL
18.43
FRONT PANEL RIGHT SIDE DETAIL
6.38
9.21
101
103
16
CENTER
ON PANEL
3.00
3.00
1.50 ±.50
.50
41
.50
96 BOTH SIDES OF PULLEY
41
32
63
.32 ±.50
34
62
CENTER ON TUBE
PATENT PENDING DECAL DETAIL
SERIAL DECAL DETAIL
ADJUSTING HANDLE DECAL DETAIL
3.00 ±1.00
.58
Product Number 8800/8810 Owner’s Manual
DECAL PLACEMENT DETAIL
Service
Page 6-11
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183
www.cybexinternational.com • techhelp@cybexintl.com