IP Link® De vice Interface
Communication Sheet
barc_1_4893_1.pke
Revision: 3/8/2011
This document provides additional assistance with wiring your Extron IP Link enabled product to your device.
Different components may require a different wiring scheme than those listed below.
For complete operating instructions, refer to the user's manual for the specific Extron IP Link enabled product or
the controlled device manufacturer supplied documentation.
Device Specifications:
Device Type:
Manufacturer:
Firmware Version:
Model(s):
Video Projector
Barco
N/A
RLM-W8
Version History:
Driver
Version
Date
1
2/22/2011
IP Link
Compiler
GC
Version
1.4.0
3.0.4
Notes
Initial version.
Driver Notes:
Pass thru mode is not recommended for this driver.
Page 1 of 5
IP Link® De vice Interface
Communication Sheet
barc_1_4893_1.pke
Revision: 3/8/2011
Control Commands & States:
Aspe ct Ratio
5:4
4:3
16:10
16:9
1.88
2.35:1
Letterbox
Native
Unscaled
Auto Image
Execute
Input
HDMI1
HDMI2
RGB
YUV 1
YUV 2
Composite Video
S- Video
RGBS
HD SDI
Lamp Mode
Eco
Standard
Low
Lamp Sele ct
Single
Dual
Picture In Picture
On
Off
PIP Input
HDMI1
HDMI2
RGB
YUV 1
YUV 2
Composite Video
S- Video
RGBS
HD SDI
Top Left
Top Right
Bottom Left
Bottom Right
Split
Powe r Control
On
Off
Vide o Mute
On
Off
PIP Position
Page 2 of 5
IP Link® De vice Interface
Communication Sheet
barc_1_4893_1.pke
Revision: 3/8/2011
Status Available:
5:4
4:3
16:10
16:9
1.88
2.35:1
Letterbox
Native
Unscaled
Connection Status
Connected
Disconnected
De vice Status
Normal
Inlet T emp Over
T emp Sensor Failure
DMD Error
Lamp Overheat
Lamp Ballast Overheated
Ballast communications
error
Lamp Ignition Failure
Lamp does not ignite
Fan Error
System Error
No Signal Present
Interlock
Software I2C Failure
GPIO Failure
EEPROM Failure
EDID Failure
EEP Version Failure
RST Gennum
Status Unavailable
HDMI1
HDMI2
RGB
YUV 1
YUV 2
Composite Video
S- Video
RGBS
HD SDI
Lamp 1 Status
On
Off
Status Unavailable
Lamp 1 Usage
Hours
Lamp 2 Status
On
Off
Status Unavailable
Lamp 2 Usage
Hours
Lamp Mode
Eco
Standard
Low
Lamp Sele ct
Single
Dual
O peration Hours
Hours
Picture In Picture
On
Off
PIP Input
HDMI1
HDMI2
RGB
YUV 1
YUV 2
Composite Video
S- Video
RGBS
HD SDI
Top Left
Top Right
Bottom Left
Bottom Right
Split
Aspe ct Ratio
Input
PIP Position
Page 3 of 5
IP Link® De vice Interface
Communication Sheet
barc_1_4893_1.pke
Powe r Control
On
Off
Powe r Status
On
Off
Cooling Down
Status Unavailable
On
Off
Vide o Mute
Revision: 3/8/2011
Warming Up
MLC62 Supported Commands:
Aspe ct Ratio
5:4
4:3
16:10
16:9
1.88
2.35:1
Letterbox
Native
Unscaled
Auto Image
Execute
Input
HDMI1
HDMI2
RGB
YUV 1
YUV 2
Composite Video
S- Video
RGBS
HD SDI
Lamp Mode
Eco
Standard
Low
Lamp Sele ct
Single
Dual
Picture In Picture
On
Off
PIP Input
HDMI1
HDMI2
RGB
YUV 1
YUV 2
Composite Video
S- Video
RGBS
HD SDI
Top Left
Top Right
Bottom Left
Bottom Right
Split
Powe r Control
On
Off
Vide o Mute
On
Off
PIP Position
Page 4 of 5
barc_1_4893_1.pke
IP Link® De vice Interface
Communication Sheet
Revision: 3/8/2011
Cable and Adapter Requirements:
M/F RS-232 null modem
Notes for the Device:
Set projector control to RS-232 on OSD as following:
Control Æ Projector Control Æ RS-232
Serial communication:
Port Type : RS-232
Baud Rate: 38400
Data Bits: 8
Parity: None
Stop Bits: 1
Flow Control: None
Pin Assignments Diagram:
Note: Captive screw connector may also be used as a serial connection.
General Notes:
Page 5 of 5