5330 IP and 5340 IP Phones User Guide

5330 IP and 5340 IP Phones User Guide

MITEL

SX-200 IP Communications

Platform

53

30 IP and 5340 IP Phones

User Guide

NOTICE

The information contained in this document is believed to be accurate in all respects but is not warranted by Mitel Networks™ Corporation (MITEL

®

). The information is subject to change without notice and should not be construed in any way as a commitment by Mitel or any of its affiliates or subsidiaries. Mitel and its affiliates and subsidiaries assume no responsibility for any errors or omissions in this document. Revisions of this document or new editions of it may be issued to incorporate such changes.

No part of this document can be reproduced or transmitted in any form or by any means - electronic or mechanical - for any purpose without written permission from Mitel Networks

Corporation.

TRADEMARKS

Mitel is a trademark of Mitel Networks Corporation.

Windows and Microsoft are trademarks of Microsoft Corporation.

Other product names mentioned in this document may be trademarks of their respective companies and are hereby acknowledged.

Mitel 5330 IP and 5340 IP Phones - User Guide

April 2008

®,™ Trademark of Mitel Networks Corporation

© Copyright 2008, Mitel Networks Corporation

All rights reserved

Mitel 5330/5340 IP Phones - User Guide

TABLE OF CONTENTS

ABOUT YOUR PHONE ........................................................................................ 1

Ring/Message Indicators...........................................................................................................3

Tips For Your Comfort And Safety................................................................................. 4

Don't cradle the handset! ..........................................................................................................4

Protect your hearing ..................................................................................................................4

Adjust the viewing angle............................................................................................................4

Using Your Default Phone Window And Keys ............................................................... 5

Getting Started with Your Phone...............................................................................................5

USING YOUR PHONE APPLICATIONS .............................................................. 7

Using the Settings Application ....................................................................................... 7

Customizing Your Phone ............................................................................................... 8

Using the Dial Pad to Enter Information....................................................................................8

Using the Onscreen Keyboard to Enter Information .................................................................8

Specify User Information ...........................................................................................................9

Specify Language......................................................................................................................9

Specify Display Brightness and Contrast ..................................................................................9

Specify Audio Feedback Options ............................................................................................10

Specify Text Size.....................................................................................................................10

Adjust Ringer Volume and Pitch .............................................................................................11

Enable a Screen Saver ...........................................................................................................12

Programming Features On Your Keys......................................................................... 13

Program Feature Keys Using the Settings Application ...........................................................15

Edit Key Labels .......................................................................................................................15

Clear Programming from a Key...............................................................................................15

Program Superkey to a Key ....................................................................................................16

To program Speed Call ...........................................................................................................16

Programming Applications on Your Keys .................................................................... 17

Making And Answering Calls ....................................................................................... 18

Using the People Application ..................................................................................................18

Phone Book .............................................................................................................................19

Answer a call ...........................................................................................................................19

End a call.................................................................................................................................19

Redial ......................................................................................................................................19

Handsfree Operation ...............................................................................................................19

Auto Answer ............................................................................................................................20

Call Handling ............................................................................................................... 21

Hold .........................................................................................................................................21

Mute.........................................................................................................................................21

Transfer ...................................................................................................................................21

iii

Mitel 5330/5340 IP Phones – User Guide

Conference..............................................................................................................................22

Swap........................................................................................................................................22

Call Forwarding .......................................................................................................................22

Using Other Features .................................................................................................. 23

Account Codes ........................................................................................................................23

ACD .........................................................................................................................................23

Attendant Call Hold - Remote Retrieve ...................................................................................23

Auto Latch Microphone ...........................................................................................................24

Callback...................................................................................................................................24

Call Forward - Remote (I Am Here) ........................................................................................24

Call Logging (Call History).......................................................................................................25

Call Park ..................................................................................................................................26

Call Pickup ..............................................................................................................................26

Campon ...................................................................................................................................27

Direct Paging...........................................................................................................................27

Do Not Disturb.........................................................................................................................29

Group Listen............................................................................................................................29

Group Paging / Meet Me Answer ............................................................................................30

Headset Operation ..................................................................................................................30

Make Busy...............................................................................................................................31

Messaging - Advisory ..............................................................................................................31

Messaging - Callback ..............................................................................................................31

Messaging - Cancel Callback..................................................................................................32

Music .......................................................................................................................................32

Night Answer ...........................................................................................................................32

Override (Intrude) ....................................................................................................................33

Paging .....................................................................................................................................33

Record a Call...........................................................................................................................33

Reminder .................................................................................................................................34

Speed Call ...............................................................................................................................34

Trunk Flash .............................................................................................................................35

Using Your Phone With The 5310 IP Conference Unit ................................................ 35

Access the Conference Controller ..........................................................................................35

Turn the conference unit on and off ........................................................................................35

Adjust the conference unit volume ..........................................................................................35

Place the conference unit in Presentation mode ....................................................................35

Exit the conference controller..................................................................................................35

Mute the conference unit.........................................................................................................35

USING YOUR PHONE WITH CORDLESS MODULE & ACCESSORIES ......... 36

Handset/Headset Combinations .............................................................................................38

Pairing the Cordless Module and Accessories........................................................................38

Cordless Module LED Indicators.............................................................................................39

Using the Cordless Handset ........................................................................................ 40

iv

Mitel 5330/5340 IP Phones - User Guide

Elements of the Cordless Handset..........................................................................................40

Answer a call ...........................................................................................................................41

Hang up ...................................................................................................................................41

Dialing – Auto Dial Disabled....................................................................................................41

Dialing – Auto Dial Enabled ....................................................................................................41

Alerting Tones and LEDs ........................................................................................................41

Checking Battery Level of Cordless Accessories ...................................................................42

Replacing Batteries in Cordless Accessories..........................................................................42

Viewing Cordless Accessory Information................................................................................42

Using the Cordless Headset ........................................................................................ 43

Answer a call ...........................................................................................................................44

Hang up ...................................................................................................................................44

Dialing – Auto Dial Disabled....................................................................................................44

Dialing – Auto Dial Enabled ....................................................................................................44

Headset Alerting Tones and LEDs..........................................................................................44

Checking Battery Level of Cordless Accessories ...................................................................45

Replacing Batteries in Cordless Accessories..........................................................................45

Viewing Cordless Accessory Information................................................................................45

Using the Cordless Devices Application ...................................................................... 46

Viewing Cordless Module Information.....................................................................................46

Low Battery Level....................................................................................................................46

Auto Dial ..................................................................................................................................46

Using a Cordless Device as a Remote Control............................................................ 47

v

Mitel 5330/5340 IP Phones - User Guide

ABOUT YOUR PHONE

The Mitel

®

5330 and 5340 IP Phones are full-feature, dual port, dual mode enterprise-class telephones that provide voice communication over an IP network. They both feature a large graphics display (160 x 320) and self-labeling keys. The 5330 IP Phone offers 24 programmable multi-function keys, and the 5340 IP Phone offers 48 programmable multi-function keys for onetouch feature access. Both phones provide ten fixed feature keys for convenient access to features such as Conferencing, Redial, and many customizable user settings as well as navigational keys to access various screens and application layers.

The 5330 and 5340 IP Phones support Mitel Call Control (MiNet) protocol and session initiated protocols (SIP). Both phones support the 5310 IP Conference Unit. The 5330/5340 phones are ideal for executives and managers, and can be used as an ACD Agent or Supervisor Phone, as well as a Teleworker Phone.

Line 4

Line 3

Line 2

Line 1

105

2:39 28-SEP-06

The 5330 IP Phone

1

Mitel 5330/5340 IP Phones – User Guide

Redial

2:39 28-SEP-06

Messaging

Line 6

Line 5

Line 4

Line 3

Line 2

Line 1

100

The 5340 IP Phone

Elements of Your Phone

Feature

Display

Ring/Message

Indicator

Volume, Speaker and

Mute Controls

Function

Provides a large, high-resolution viewing area that assists you in selecting and using phone features.

Flashes to signal an incoming call and to indicate a message waiting in your voice mailbox.

Provide the following audio control capability:

(UP) and (DOWN) provide volume control for the ringer, handset, and handsfree speakers.

(SPEAKER) enables and disables Handsfree mode.

(MUTE) enables Mute, which allows you to temporarily turn your phone's handset, headset or handsfree microphone off during a call.

2

Mitel 5330/5340 IP Phones - User Guide

Feature Function

Fixed Function Keys Give you access to the following phone functions:

(SETTINGS) : provides access to menus for your phone's additional features.

(CANCEL) : ends a call when pressed during the call, and, when you are programming the phone, eliminates any input and returns to the previous menu level.

(REDIAL) : calls the last number dialed.

(HOLD) : places the current call on hold.

(TRANS/CONF) : initiates a call transfer or establishes a threeparty conference call.

(MESSAGE) : provides access to your voice mailbox and flashes to notify you of messages waiting in your voice mailbox. Note : The

Ring/Message indicator also flashes when messages are waiting.

Keypad Use to dial.

Navigation Page Keys Use to display additional pages of information. The 5330 has two page navigation keys: Back and Next. The 5340 has three page navigation keys: Back, Next, and Home.

Programmable Feature

Keys and Softkeys.

Provides 24 (on the 5330) and 48 (on the 5340) self-labeling keys that can be programmed as speed call keys, fixed function keys, applications, or line appearance keys, according to your communication needs On your home page, the bottom right feature key is always your Prime Line key on a 5340 IP Phone; and the bottom left feature key is always your

Prime Line key on the 5330 IP Phone. The top three keys are softkeys.

Handsfree Speaker Provides sound for Handsfree calls and background music.

Handset Use for handset calls. If you are in headset or handsfree mode, you do not need to use the handset.

Ring/Message Indicators

When indicator is it means that

Flashing rapidly Your phone is ringing

Flashing slowly

On

Off

A message or callback message is waiting at your phone

Your phone is ringing another phone

Your phone is idle, or you are on a call

3

Mitel 5330/5340 IP Phones – User Guide

Tips For Your Comfort And Safety

Don't cradle the handset!

Prolonged use of the handset can lead to neck, shoulder, or back discomfort, especially if you cradle the handset between your ear and shoulder. If you use your phone a lot, you may find it more comfortable to use a headset. See the section on headset usage elsewhere in this guide for more information.

Protect your hearing

Your phone has a control for adjusting the volume of the handset receiver or headset. Because continuous exposure to loud sounds can contribute to hearing loss, keep the volume at a moderate level.

Adjust the viewing angle

The stand built into your phone tilts to give you a better view of the keys.

To tilt your telephone for better viewing:

1. Turn the phone so that the front faces away from you.

2. Hold the base unit firmly and press the release tabs on the sides of the stand to detach the base unit.

3. Hinge the hooks of the base unit into the notches on the back of the phone and snap into place as follows: a) For a high-angle mount, hinge the two lower hooks into the bottom set of notches and snap the two upper hooks into the middle set of notches. b) For a low-angle mount, hinge the two lower hooks into the middle set of notches and snap the two upper hooks into the top set of notches.

4

Mitel 5330/5340 IP Phones - User Guide

Using Your Default Phone Window And Keys

The 5340 and 5330 IP Phone default phone windows and keys are shown and described below.

The Phone window provides access to programmable keys and the main phone interface.

Getting Started with Your Phone

When you receive your phone, you need to program features and applications.

5330 and 5340 IP Phone Windows

5

Mitel 5330/5340 IP Phones – User Guide

5330 and 5340 IP Phone Default Window and Keys

Feature Function

Softkeys Allow you to access specific call control features, which are context sensitive.

These are non-programmable feature keys that are specific to the application or state of the set. The 5330 provides three softkeys and the 5340 provides six softkeys.

Programmable Keys Launch specific call control features. Use the Settings application or a programmed Superkey to program these keys. The 5340 provides 16 programmable keys per page (a maximum of 47 programmable keys plus 1 prime line key). The 5330 provides 8 per page (a maximum of 23 programmable keys plus 1 prime line key). For instructions on programming the keys, see

Programming Features on Your Keys

.

Page Navigation Keys Display additional pages of information The 5330 has two page navigation keys:

Back and Next, while the 5340 has three page navigation keys: Back, Next, and

Home.

Status Line Displays time, date, and icons indicating feature states as follows:

Message Waiting ( ) - Indicates new voice mail.

Information Area

Footer

Headset ( ) - Indicates that the phone is in headset mode.

DND ( ) - Indicates DND (Do not disturb) mode.

Logged in as (

) - Indicates that a hot desk user is logged in.

Conference Unit (

) - Indicates that the Conference Unit is connected and turned on.

Provides prompts in most phone applications. Content changes based on the application.

Shows context and summary information based on information in the

Programmable Keys area, such as Page Indicators and numbers of items.

6

Mitel 5330/5340 IP Phones - User Guide

USING YOUR PHONE APPLICATIONS

Your 5330 and 5340 IP Phones provide applications and settings that simplify the use of your phone. The Applications window provides access to all the phone’s applications.

To open an application, press the key beside the application name:

Applications List: Provides an onscreen access list of the applications available on your

phone. For information about programming Applications, see Programming Applications on

Your Keys on page 17.

People (5340 IP Phone only): Use the People application to add, edit, or delete contact names and numbers. You can also dial anyone on your contact list from the People applications. Contacts are displayed alphabetically by last name. For more information about

using the People application, refer to Using the People Application on page 18.

Conference Unit: Use the Conference Unit application to control the 5310 IP Conference

Unit. Use this application to turn the conference unit off or on, to adjust the volume, or to put the conference unit into Presentation mode. You can only run one Conference Controller session at a time. The Conference Unit application is available only when your phone is connected to a 5310 Conference Unit. See

Using Your Phone with the 5310 Conference Unit on page 35 for more information.

Settings: Use the Settings application to display and quickly change your phone’s current

communications settings. See Using the Settings Application on this page for more

information.

Cordless Devices: Use the Cordless Module application to configure and view status of

cordless accessories. See Using the Cordless Module

for more information.

Help: Provides access to Quick Help and defines all keyboard icons.

You can access phone Applications by programming an Applications feature key. For information about programming keys, see

Programming Feature Keys Using the Settings Key

on page 13.

Using the Settings Application

The Settings application provides a location to access most phone settings. You can also launch the Settings application and open the Settings window by pressing the Settings fixed function key . Select any option in the window to access another window where you can view and configure the phone settings for that option. Press the page navigation keys to see the next page of options.

The Settings window provides the following options:

User Information: For Release 4.0 of the SX-200 ICP, number information must be programmed by your System Administrator. (For information about editing names, see

Specify User Information on page 9.)

Programmable Keys: Use this option to assign features to the programmable keys on

your phone. For a list of available features, see page 13.

Languages: Allows you to select the language in which phone prompts and applications appear. Supported languages are English, French, and Spanish.

Text Size: Allows you to specify the font size (large or small) for the 5340 IP Phone.

Brightness and Contrast: Allows you to adjust the display brightness and contrast of your phone.

7

Mitel 5330/5340 IP Phones – User Guide

Screen Saver: Allows you to specify a specific time of inactivity on your phone that triggers the screen saver to display.

Audio Feedback: This setting allows you to adjust the volume of the audio feedback and the error beeps as well as enable or disable the setting.

About 5330/5340 IP Phone: This screen displays firmware release information.

Customizing Your Phone

Using the Dial Pad to Enter Information

You can use the standard dial pad keys 0-9, and * and # to enter a name and or number for applications and features. Using the dial pad is the default option. You can also use the onscreen

keyboard by selecting Keyboard while entering text (see Using the Onscreen Keyboard .).

The following table shows the characters you can enter by pressing a key consecutively. For example, to enter the letter “e”, press the ‘3’ key twice.

Key Characters

1 1

2 a b c A B C 2

3 d e f D E F 3

4 g h i G H I 4

5 j k l J K L 5

6 m n o M N O 6

7 p q r s P Q R S 7

9 w x y z W X Y Z 9

0 0

‘ ‘

Characters are automatically inserted after a one-second delay. If you make an error, use

Backspace (or Clear on the 5340) to make corrections.

Press or at the bottom of the set to move the cursor forwards or backwards without deleting characters.

Note: When a text entry window is open, you cannot use the dial pad for dialing.

Using the Onscreen Keyboard to Enter Information

The onscreen keyboard can be used to enter name and number information into applications and features:

1. When prompted to enter name/number information, press Keyboard to display the onscreen keyboard. your input.

3. Repeatedly press the key next to the character you want to enter until that character is highlighted. The character is automatically inserted after a one-second delay. If you make

8

Mitel 5330/5340 IP Phones - User Guide an error, press or at the bottom of the set to move the cursor backwards or forwards. This does not delete any characters. You can press Backspace

(or Clear on the 5340) to delete characters.

4. After you have entered all the characters, press Save.

5. Continue with text entry as required by the application, or press Close.

Specify User Information

To specify the number displayed on the phone, see your Administrator.

To edit the name displayed on the phone:

1. Press .

the or the onscreen keyboard to spell your name.

Note: Changing the name displayed on your phone changes the following items throughout the system:

• call display that is displayed to your callers

• mailbox keys

• key line appearance keys

Specify Language

To specify the language in which prompts and applications display:

1. Press .

3. Select a language and then press Save.

Note: Languages supported on the 5330/5340 may differ from those supported on the ICP. If the phone is configured for an unsupported language, the prompts may appear in your selected language but the language of the Application page defaults to English. The Language window displays "<name of the selected language> Unsupported".

Specify Display Brightness and Contrast

You can adjust the brightness and display contrast either via the phone volume controls (when the phone is idle) or via the Settings application. (On a 5330 IP Phone, you can only adjust the contrast, not the brightness.)

To adjust the display contrast using the volume controls:

• Repeatedly

(DOWN).

Note: You can use this method only when the phone is idle. If the phone is ringing, this action adjusts the ring volume. If the phone is in use, this action adjusts the handset, headset and speakerphone volume.

9

Mitel 5330/5340 IP Phones – User Guide

To adjust the display brightness and contrast using the Settings application:

1. Press .

2. Press Brightness and Contrast.

3. Press the Brightness and Contrast '+' or '-' keys to adjust the brightness and contrast of your screen.

Note: Press Cancel at any time to exit this application without making any changes.

Note: If you replace an existing 5330/40 IP phone with a Rev C or higher version using the same

Directory Number, the initial display will not have optimum settings. Follow the instructions above to set the brightness to the desired level.

Specify Audio Feedback Options

The error beep volume in the phone is related to the volume of the speaker. You can set the beep volume using this procedure; however, adjusting the speaker volume also affects the beep volume.

To adjust the volume of the audio feedback:

1. Press .

3. Set the options using the appropriate actions described below:

Option

Turn audio feedback off for errors

Adjust audio for error beeps

Test audio feedback volume level

Action

Press Turn Off.

Press Volume + or Volume –

Press Play Error Tone

Note: Press Cancel at any time to exit this application without making any changes.

Specify Text Size

To specify the text size that displays on the phone:

1. Press .

Note: The default text size is "Small". In some instances, using Large Text size may result in truncated key labels. To restore proper key labeling, switch to the Small Text setting.

10

Mitel 5330/5340 IP Phones - User Guide

Adjust Ringer Volume and Pitch

To adjust Ringer Volume while the phone is idle:

5330 Phone:

1. Press the key that you have programmed as Superkey.

5340 Phone:

1. Press the key that you have programmed as Superkey. appears.

2. Press More until the Ring Adjust option appears.

3. Press Ringer Vol.

5. Press “Ringer Vol”.

6. Press (UP) or (DOWN) .

4. Press (UP) or (DOWN) .

5. Press Superkey

To adjust Ringer Pitch while the phone is idle:

5330 Phone:

1. Press the key that you have programmed as Superkey. appears

5340 Phone:

1. Press the key that you have programmed as Superkey.

2. Press More until the Rng Adjust option appears

3. Press Ringer Pitch.

5. Press (UP) or (DOWN).

4. Press (UP) or (DOWN) .

5. Press Superkey

To adjust Ringer Volume while the phone is ringing:

• Press (UP) or

(DOWN).

Note:

• If the phone is in talk state, pressing UP or DOWN adjusts the volume of the handset, headset or speaker.

• If the phone is idle, pressing UP or DOWN adjusts the contrast.

11

Mitel 5330/5340 IP Phones – User Guide

Enable a Screen Saver

You can program your screen saver to turn on when a specific time period of inactivity has occurred on your phone. The screen saver displays set type, software load, hardware revision, and ICP software load.

To enable a screen saver:

1. Press .

3. Select the inactivity time that will activate the backlight switch to dim.

4. Press the checkbox beside Display image if you want the screen saver image to display. If you prefer to have backlight dimming only (no image), then do not select this box.

5. You can use the Brightness options to adjust the brightness of the screen saver if necessary.

12

Mitel 5330/5340 IP Phones - User Guide

Programming Features On Your Keys

You can assign Features (like "Speed Call") or Applications (like "People") to the programmable keys on your phone.

Most features can be programmed using the Settings key but the following features/settings require you to use a Superkey (which you have programmed to a key):

• Display Key Programming (5340 only)

• Speed Call when "Private" setting is required

• Split Call Forwarding

• Display Name changes

• Night Answer

Note: Features available on the Superkey are dependent upon system programming. See your

System Administrator if you require a feature that is not listed on your phone.

Features available for programming on programmable keys:

Features listed with an asterisk are listed under the Settings key but are not functional in this release. Use the Superkey to program these features.

Account Code Verified Acct Verified

Alarm Alarm

Auto Answer Auto Ans

Call Block

Call Park

Call Block

Call Park

Call Pickup Call Pickup

Call History* Call Hist

Campon Campon

Day/Night Day/Night

Direct Page Page

Do Not Disturb

Double Flash

DND

Dbl Flash

Forward all*

Forward Always*

Fwd all

Fwd Always

Forward Busy*

Forward Busy/No Answer*

Forward Call*

Forward No Answer*

Fwd Busy

Fwd B/NA

Fwd call

Fwd No Ans

13

Mitel 5330/5340 IP Phones – User Guide

Group Listen Grp Listen

Guest Room

Handset Mute

Guest Room

Hndset Mut

Headset Headset

Music Music

Night Answer

Open Door

Night Ans

Open Door

Orbit Orbit

Override Override

Paging* Paging

Park PA Prk PA

Park Page

Park Page Group

Prk Page

Prk Pg Grp

Park Page Set Prk Pg Set

Phonebook Phonebook

Privacy Release

Record Call

Privacy Rls

Rec Call

Release Release

Respond Respond

Single Flash

Speed Call

Flash

Speed Call

Superkey Superkey

Swap Swap

System Park

Voice Mail

System Prk

Voice Mail

Voice Mail Prompts

Wake Up Alarm

VM Prompts

WkUp Alarm

Note: Some feature availability is dependent upon system programming.

For more information about programming Features and Fixed Functions to a key see Program

Feature Keys Using the Setting Application on page 15.

For more information about programming Applications to a key, see

Programming Applications on Your Keys on page 17.

Note: Only the System Administrator can program "line select" and "line appearance" keys. By default, the user’s Prime line is Key 1.

14

Mitel 5330/5340 IP Phones - User Guide

Program Feature Keys Using the Settings Application

To program a phone feature:

1. Press .

3. Press the key you want to program.

4. If Applications are displayed, press the View Features softkey. (Conversely, if you want to program an application to this key, and features are displayed, press the View

Applications softkey.)

5. Use the Page Navigation keys to move through the features list. (Features are listed in the order they are most frequently used.)

6. Select the desired feature or fixed function key from the list. A default label is automatically assigned to the key. If you want to personalize the label, refer to Edit Key

Labels on page 15.

7. Enter the required information in the fields provided, if necessary.

Edit Key Labels

To change the labeling of a programmed feature key:

1. Press .

2. Press Programmable Keys.

3. Select the key you want to edit.

the or the onscreen keyboard to enter the new label.

7. When label entry is complete, press Save.

Clear Programming from a Key

You may wish to clear the programming from a key if you are no longer using it.

To clear the feature or application programming from a key:

1. Press .

3. Press the key you wish to clear.

4. Press Clear Key.

15

Mitel 5330/5340 IP Phones – User Guide

Program Superkey to a Key

To program a feature key to be the Superkey:

1. Press .

3. Press the key you wish to program.

4. If Applications are displayed, press View Features.

5. Use the Page Navigation keys to move through the features list.

Note: You cannot program a Superkey on keys 31 to 48 of the 5340 phone.

Program Feature Keys Using the Superkey

To program a phone feature key:

5330 Phone:

1. Press the key that you have programmed as Superkey.

5340 Phone:

1. Press the key that you have programmed as Superkey then press Yes.

3. Press the key you want to program. option appears, if necessary

3. Press Feature Key.

4. Press the key you want to program. program appears, and then press Yes.

6. Select the key type to program. (Press

More to scroll, if necessary.)

To program Speed Call

You can use the Settings key or the Superkey to program Speed Calls keys.

Note: The Settings key does not offer the "Private" option. If you want the Speed Call number to be private, use the Superkey to program it.

To program Speed Call Using the Settings Key:

3. Select the key to program.

4. Use page navigation keys to find Speed Call

5. Press

dial pad

or the

onscreen keyboard

.

• Maximum length is 26 characters (valid characters are 0-9, # and *.)

16

Mitel 5330/5340 IP Phones - User Guide

To Program Speed Call Using Superkey:

5330 Phone:

1. Press the key that you have programmed as Superkey.

2. Press No until Personal Keys? appears and then press Yes.

3. Press the key you want to program.

4. Press Change.

5340 Phone:

1. Press the key that you have programmed as

Superkey.

2. Press the More key until Feature Key appears.

3. Press Feature Key.

4. Press the key you want to program.

6. Enter the speed call number using the dial pad.

7. If you want the number to be private, press Priv.

8. Press Save. Key programming is saved with the default "Speed Call" label.

9. Press Superkey to exit. To edit the label or number, refer to Editing Key

Labels on page 15.

6. Press Speed Call.

7. Enter the speed call number using the dial pad.

8. If you want the number to be private, press

Priv.

9. Press Save. Key programming is saved with the default "Speed Call" label.

10. Press Superkey to exit. To edit the label or number, refer to Editing Key Labels on

page 15.

Programming Applications on Your Keys

The following applications are available for programming on programmable keys:

• People

• Settings

• Help

To program a Phone Application:

1. Press .

3. Press the key you want to program.

4. If Features are displayed, press View Applications.

5. Select the desired application.

Note: The Applications List feature key may display an incorrect count of available applications.

17

Mitel 5330/5340 IP Phones – User Guide

Making And Answering Calls

You can make a call using one of the following methods:

• Press the programmed Speed Call key associated with the party you want to call. For

more information about programming keys, see Programming Features On Your Keys

on

page 13.

• Dial the number using the dial pad.

Using the People Application

You can use the People Application to maintain a list of contacts with one-touch dialing.

To add a name to your contact list using the People application:

3. Enter the number using the dial pad or the onscreen keyboard

. (Valid characters are 0-9,

#, and *.)

5. Enter the name of your contact using the dial pad or the onscreen keyboard

.

To edit information in your People list

2. Press the name you want to edit. (If you want to delete the name from your contact list, press Delete.)

the

or the

onscreen keyboard

, update the appropriate information.

the

or the

onscreen keyboard

, update the appropriate information. (Valid characters are 0-9, #, and *.)

To dial a contact from your People list:

1. Open the People application.

2. Use the navigation keys to page through the contact list and select the name.

3. Dial the contact name using one of the following methods:

• Select a contact name and press Dial.

• Press the key to the right of the contact’s dial icon in the main list. (The contact name does not need to be selected.)

4. Continue the call using the speakerphone or lift the handset.

18

Mitel 5330/5340 IP Phones - User Guide

Phone Book

To use Phone Book:

2. Enter the name of the desired party, as follows:

• For each letter in the name, press the appropriate key on the keypad until the letter is shown in the display. For example, if the letter C is required, press the '2' keypad digit three times.

• Use the <— softkey to correct errors.

• If required, press —> softkey to add a space between the first and last name.

4. If no match exists, edit the original entry.

5. If more than one match is found, press the Next softkey.

6. Do one of the following:

• To make the call, press the Call softkey.

• To edit the entry, press the Backup softkey.

• To exit, press Close or Superkey.

Answer a call

Do one of the following:

• Select the programmable line key for the ringing line that is flashing.

• Lift the handset or press (SPEAKER).

End a call

Do one of the following:

• Press Hang Up or Cancel (

).

• Replace the handset.

• Press the key that you have programmed as Cancel.

• If you are in Handsfree mode, press (SPEAKER).

Redial

To redial the last number that you manually dialed:

1. Lift the handset (optional).

2. Press (REDIAL) or the key you programmed as Redial.

Handsfree Operation

To use Handsfree to make a call:

1. If you want to use a Non–Prime Line, press a Line Appearance key.

Note: Your administrator must program Line Appearances to your phone.

19

Mitel 5330/5340 IP Phones – User Guide

2. Dial the number.

3. Begin speaking when the called party answers. Your phone's Handsfree microphone and

Handsfree speaker transmit and receive audio.

To use Handsfree operation to answer calls:

• Press the flashing line key.

• Begin speaking. Your phone's Handsfree microphone and Handsfree speaker transmit and receive audio.

To hang up while using Handsfree operation:

• Press (SPEAKER).

To turn Mute on during Handsfree operation:

• Press (MUTE). The Mute key light turns ON.

To turn Mute off and return to conversation:

• Press (MUTE). The Mute key light turns OFF.

To disable Handsfree operation:

• Lift the handset.

To return to Handsfree operation:

1. Press (SPEAKER).

2. Hang up the handset.

Auto Answer

When the Auto Answer feature is active, incoming calls ring briefly, and then the phone answers the call in Handsfree mode. You can continue the call handsfree or use the handset.

To enable or disable Auto-Answer:

• Press the key you have programmed as Auto Answer. The key is illuminated and all incoming calls are answered in Handsfree mode.

To switch from Handsfree mode to handset mode:

• Lift the handset.

To end a call, do one of the following:

• Press (Cancel)

• Wait for the caller to hang up.

20

Mitel 5330/5340 IP Phones - User Guide

Call Handling

Hold

To place a call on Hold, do one of the following:

• Press

(HOLD).

• Press the key that you have programmed as Hold. The indicator flashes on the line that has the held call.

Note: You can only retrieve a call from hold when the phone is idle.

To retrieve a call from Hold, do one of the following:

• Lift the handset and press the flashing line.

• Press the flashing indicator.

To retrieve a call from Hold at another phone, do one of the following:

• Press the flashing line key.

• Dial the appropriate feature access code and the number of the station that placed the call on Hold.

Mute

Mute lets you temporarily turn your phone's handset, headset or handsfree microphone off during a call.

To turn Mute on during a call:

• Press (MUTE). The (MUTE) light turns ON.

To turn Mute off and return to the conversation:

• Press (MUTE). The (MUTE) light turns OFF.

Note: If you are on a Handsfree MUTED call and you lift the handset, the handset microphone is automatically enabled and the MUTE light turns OFF.

Transfer

To transfer an active call:

1. Press (TRANS/CONF).

2. Dial the number of the third party.

3. Do one of the following:

• To complete the Transfer, hang up.

• To announce the Transfer, wait for an answer, consult, and hang up.

• To cancel the Transfer, press (CANCEL).

To transfer an active call during headset operation:

1. Press (TRANS/CONF).

2. Dial the number of the third party.

3. To complete the Transfer, press the Release feature key.

21

Mitel 5330/5340 IP Phones – User Guide

Conference

To form a Conference when a two–party call is already in place, or to add another party to an existing Conference:

1. Press (TRANS/CONF).

2. Dial the number of the next party.

3. Wait for an answer.

4. Press (TRANS/CONF).

To leave a Conference:

• Hang up or press

(CANCEL).

Swap

To call another party when you are in an established two–party call:

1. Press (TRANS/CONF).

2. Dial the number.

To alternate between the two parties:

• Press the key you have programmed as Swap.

Call Forwarding

Call Forwarding lets you redirect incoming calls to an alternate number when your phone is busy, when you're not answering, or all the time.

You can use the Settings key to set a global forwarding option for all calls, or to program a feature key with a desired forwarding method. If you need one forwarding setup for Internal calls and a different setup for External calls, use the Superkey to program Call Forwarding.

Programming Call Forward

To set a global Call Forward option for all calls:

5330 Phone:

1. Press the key that you have programmed as Superkey.

5340 Phone:

1. Press the key that you have programmed as Superkey. if necessary. option appears. calls.

Call Forward categories (Always?, If Busy?,

No Ans?, etc.) and then press Pgm to select.

5. Enter the number to which you want your calls forwarded and then press Save.

4. Press the key for your desired forwarding option (Busy, Always, To me, No Ans)

22

Mitel 5330/5340 IP Phones - User Guide

To program a feature key with a specific call forward option:

5330 Phone: 5340 Phone:

1. Press the key that you have programmed as Superkey.

1. Press the key that you have programmed as Superkey. and then press Yes.

3. Select the key on your phone that you want to program. option (FWD ALWAYS, BUSY, NO ANS, etc.) appears and then press Yes. option appears.

4. Select the key on your phone that you want to program. option appears and then select it.

Using Other Features

Account Codes

An account code is a series of digits that you assign to your calls, usually for accounting purposes. The code identifies the account in the call records that your system generates. A forced account code is usually entered from another extension, enabling you to use features or make calls that the extension otherwise could not. If you want this feature enabled on your phone, ask your System Administrator.

To use Account Codes:

1. Lift the handset.

2. Dial the Account Code digits.

To enter an Account Code during a call:

1. Press the key that you have programmed as Account Code Verified.

2. Dial the Account Code digits.

ACD

If your phone is ACD-enabled, you can log in as an agent.

To log in as an ACD agent:

1. Lift the handset.

2. Dial the ACD Login/Logout feature access code.

3. Enter your Agent ID, using the key pad.

Attendant Call Hold - Remote Retrieve

To retrieve a call placed on Hold by the attendant:

1. Lift the handset.

2. Dial the "Call Hold – Remote Retrieve" feature access code.

3. Dial the digits announced by the attendant.

23

Mitel 5330/5340 IP Phones – User Guide

Auto Latch Microphone

To set the Handsfree microphone to automatically turn on or off when receiving a page or

Intercom call:

1. Press the key you have programmed as Superkey.

3. Press Auto Latch Mic.

Microphone feature is in use.

Callback

The Callback feature allows you to be notified when a busy phone becomes free or when a phone has been used after a no-answer condition was encountered.

To request a Callback when you reach a busy or unanswered station:

When the party is available, your phone rings and the display shows the Callback ringing indicator.

To answer a Callback:

• Lift the handset.

Call Forward - Remote (I Am Here)

You can program "I Am Here" forwarding from a remote station or from your current location.

To forward calls from a remote station to your current location:

5330 Phone:

1. Press the key that you have programmed as Superkey.

5340 Phone:

1. Press the key that you have programmed as Superkey.

Forwarding?" appears. appears. appears.

3. Press To Me.

4. Enter the extension of the remote station. If you make an error while dialing, use the

<— softkey to backspace and correct the number.

6. Enter the extension of the remote station. If you make an error while dialing, use the <— softkey to backspace and correct the number.

7. Press (DOWN) or the Save softkey.

24

Mitel 5330/5340 IP Phones - User Guide

To cancel "Call Forward – Remote" from the station that was forwarded (the remote station):

5330 Phone:

1. Press the key that you have programmed as

Superkey.

5340 Phone:

setting you want to change. and then press Yes. Programmed settings appear with an * beside the name. setting.

To cancel "Call Forward – Remote" from the station that received the forwarded calls (the current location):

1. Lift the handset.

2. Dial the "Call Forwarding – Cancel I'm Here" feature access code.

Call Logging (Call History)

Call Logging keeps track of the names (if available) and telephone numbers of all your incoming calls or only those you missed.

To program your phone to log incoming calls:

5330 Phone:

1. Press the key that you have programmed as

Superkey.

5340 Phone:

1. Press the key that you have programmed as Superkey then press Yes. appears extensions only, External to log outside calls only, or Both to log both internal and external. extensions only, External to log outside calls only, or Both to log both internal and external.

To turn off call logging:

5330 Phone:

1. Press the key that you have programmed as

Superkey.

5340 Phone:

1. Press the key that you have programmed as Superkey then press Yes. appears

25

Mitel 5330/5340 IP Phones – User Guide

To display the call log:

5330 Phone: 5340 Phone:

History feature key. (see page 16 for key

programming instructions.) The Call History feature key illuminates when call history is present. number of old calls and new calls. (Note: this key is only available when call history data is present.) old calls and new calls. Press New Calls to view calls that have arrived since your last review or press Old Calls to view previously-viewed calls arrived since your last review or press

Old Calls to view previously-viewed calls.

Press Delete All to delete all call logs.

Press Call to return the call.

Press Delete All to delete all call logs.

Press Call to return the call.

Call Park

The Call Park feature allows you to place a call in a special hold state. You, or someone else, can then retrieve the call from any extension in the system.

After parking the call, the system can automatically connect you to paging equipment so that you can announce the call to the requested party.

To park an active call:

1. Do one of the following:

• Press the key that you have programmed as Call Park.

• Press

(TRANS/CONF), and then dial the appropriate feature access code.

The display shows [email protected], followed by the park destination and parking spot index (if applicable). Example: [email protected] 1234 @ 02.

2. Dial the directory number on which to park the call (not required if the number is programmed to the Call Park feature key).

3. To inform a user that a parked call is waiting, do one of the following:

• If automatic paging is enabled, announce the call and the park retrieve digits shown on the display.

• If automatic paging is disabled, press the programmed Page key, or dial the appropriate feature access code, followed by the Paging zone number (if required). Then, announce the call and park retrieve digits shown on the display.

Note: Paging over a loudspeaker is not permitted in handsfree mode; you must use the handset or headset.

To retrieve a parked call:

1. Dial the "Call Park Orbit Retrieve" feature access code.

2. Dial the two-digit orbit number.

Call Pickup

To answer a call that is ringing at another extension in your Pickup Group:

26

Mitel 5330/5340 IP Phones - User Guide

1. Lift the handset.

2. Press the key that you have programmed as Call Pickup.

To answer a call that is ringing at another extension not in your Pickup Group:

1. Lift the handset.

2. Dial the Directed Call Pickup feature access code.

3. Dial the number of the ringing station.

Campon

When you get a busy tone, you can use the Campon feature to be notified when the busy party becomes available.

To Campon to a busy station:

To retrieve a call when you hear the Campon tone:

• You can use the Call Swap feature with the programmable line key.

(TRANS/CONF) hardkey or a

Direct Paging

Direct Paging allows you to page a party through the party’s handsfree speaker. If the paged party has Off-Hook Voice Announce enabled, the page will be heard even when the party is on a handset or headset call. If the paged party has Handsfree Answerback enabled and turned on at the phone, your page automatically establishes a handsfree call with the paged party.

To page a party:

1. Lift the handset.

2. Press the Direct Paging feature key you have programmed, or dial the appropriate feature access code.

3. Dial the extension number.

4. Speak to the dialed party after the tone.

How you answer a Direct Page depends on whether Handsfree Answerback is enabled and turned on at your phone. See one of the following procedures:

• Direct Paging - Handsfree Answerback Enabled

• Direct Paging - Handsfree Answerback Disabled

Direct Paging - Handsfree Answerback Enabled

When you receive a Direct Page, Handsfree Answerback automatically establishes a Handsfree call on your phone after a single burst of tone.

Your administrator enables or disables Handsfree Answerback on your phone. After your administrator enables Handsfree Answerback, you can choose to turn it on or off directly from your phone.

To turn Handsfree Answerback on:

• When your phone is idle, press (MUTE) once. The MUTE key light flashes to indicate that Handsfree Answerback is ON.

27

Mitel 5330/5340 IP Phones – User Guide

• When a Direct Page arrives, the MUTE key light turns OFF and a Handsfree call is automatically established.

To turn Handsfree Answerback off:

• Press the flashing (MUTE) key once. The MUTE key light turns OFF.

• To respond to a Direct Page when Handsfree Answerback is OFF, see "Direct Page -

Handsfree Answerback Disabled" elsewhere in this guide.

Note: By default, Handsfree Answerback is turned OFF at your phone. If the (MUTE) key is

OFF when your set is idle, Handsfree Answerback is OFF.

To answer a call using Handsfree Answerback:

Phone state before Page arrives

Phone is idle and MUTE is flashing

You are on a handset or headset call, and MUTE is OFF

You are on a MUTED handset/headset call, OR, you are on a Handsfree call

To answer the Direct Page

1. Check that MUTE is OFF.

2. Listen for the paging party.

3. Begin speaking.

4. Lift the handset if you wish to switch from a

Handsfree call to a handset call.

1. Check that MUTE is flashing.

2. Press MUTE. The light turns ON solid, and you are now speaking to the paging party and have muted your handset/headset call.

3. Speak to the paging party. Press MUTE to alternate between handset/headset and handsfree calls.

The party paging you receives a busy tone. Handsfree

Answerback does not interrupt your call.

To end a Handsfree Answerback call:

• Press

(CANCEL).

When the Handsfree Direct Page call ends, the MUTE key light returns to the state it was in before the call was established.

Direct Paging - Handsfree Answerback Disabled

Your administrator enables or disables Handsfree Answerback and you can also turn it on or off on your phone. To turn Handsfree Answerback off, see "Direct Paging - Handsfree Answerback

Enabled" elsewhere in this guide. When Handsfree Answerback is disabled on your phone and you receive a Direct Page, the Direct Page is indicated by a single burst of tone.

28

Mitel 5330/5340 IP Phones - User Guide

To answer Direct Page calls when Handsfree Answerback is disabled:

Phone state before Page arrives: To answer the Direct Page

(indicated by single burst of tone):

Phone is idle and MUTE is OFF. 1. Check that MUTE is ON solid.

2. Lift the handset OR press MUTE key to answer in

Handsfree mode. (The light turns OFF.)

You are on a handset call or headset call, and MUTE is OFF

You are on a MUTED handset/headset call, OR, you are on a Handsfree call

3. Begin speaking.

1. Check that MUTE is flashing.

2. Press MUTE. The light turns ON solid and you are now speaking to the paging party and have MUTED your handset/headset call.

3. Speak to the paging party. Press MUTE to alternate between handset and handsfree calls.

The party paging you receives a busy tone. Handsfree

Answerback does not interrupt your call.

To end a Direct Page call, do one of the following:

• Hang up the handset to end a handset call.

• Press (SPEAKER) to end a Handsfree call.

• Press (CANCEL).

When the Handsfree Direct Page call ends, the (MUTE) key light returns to the state it was in before the call was established.

Do Not Disturb

When you enable Do Not Disturb, callers are immediately transferred to voice mail.

To activate or deactivate Do Not Disturb:

Disturb is activated and is not illuminated when Do Not Disturb is not activated.

Group Listen

With Group Listen, you can carry on a conversation using the handset or headset while allowing others nearby to listen to the person at the far end over the handsfree speaker. The handsfree microphone is disabled in Group Listen mode.

To activate Group Listen while in a handset conversation:

• Press the key you have programmed as Group Listen. Audio from the far-end party is now heard through both the handset/headset and the speaker.

To make the call a normal two-way speaker call:

• Press (SPEAKER).

To exit Group Listen mode (and return to a normal handset/headset call):

29

Mitel 5330/5340 IP Phones – User Guide

To activate or deactivate Group Listen while in headset mode:

Group Paging / Meet Me Answer

Group Paging allows you to page a group of telephones through their built-in speakers. You can belong to as many as three paging groups with one group designated as your "prime" group.

When you need to respond to a Group Page but don't know the identity or extension number of the paging party, use the Meet Me Answer feature. You have up to 15 minutes after receiving the page to use Meet Me Answer.

To make a Group Page:

1. Lift the handset.

2. Press the Direct Page key you programmed, or dial the Direct Paging feature access code.

3. Do one of the following:

• To page your prime page group, press #.

• To page a specific page group, dial the page group directory number.

4. Speak to the dialed party after the tone.

To respond to a Group Page by using Meet Me Answer:

2. Dial the "Meet Me Answer" feature access code.

3. Do one of the following:

• To respond to a page from your prime page group, press #.

• To respond to a page from a specific page group, dial the page group directory number.

Headset Operation

To enable Headset Operation:

• Press the key that you have programmed as Headset Mode.

To answer a call (when Auto Answer is disabled):

• Press the flashing line key.

To answer call (when Call Notification is enabled)

To hang up:

• Press (CANCEL).

To mute your headset microphone:

To turn mute off and return to the conversation:

30

Mitel 5330/5340 IP Phones - User Guide

Make Busy

When the ACD feature is enabled, you can use the Make Busy feature to have your phone appear busy to other callers. If callers dial your phone number when Make Busy is enabled, a message indicating that your line is busy is displayed on their phones.

To enable Make Busy:

• Press the key that you have programmed as Make Busy. The key illuminates when

Make Busy is activated and MAKE BUSY is displayed.

To disable Make Busy:

• Press the key that you have programmed as Make Busy. The key light goes out.

Messaging - Advisory

Advisory Messaging enables you to select a notice that appears on your phone display to inform people calling you of your whereabouts. Select from a variety of advisory messages, including

"On vacation", "In a meeting", or "Out to Lunch".

To turn Messaging - Advisory on:

5330 Phone:

1. Press the key that you have programmed as Superkey.

5340 Phone:

appears and then press Yes.

3. Press the Next softkey until the desired message appears. message appears.

4. Press Turn Msg On.

To turn Messaging - Advisory off:

5330 Phone:

1. Press the key that you have programmed as Superkey.

5340 Phone:

appears and then press Yes. displays the current advisory message.

3. Press Turn Msg Of.

Note: You can also create your own Advisory Messages if your System Administrator has programmed this option. When a custom advisory message is enabled and in use on more than one 5340 phone, hitting the Create Message softkey supplies a “Force Off” softkey. This key allows you to force the message to change on all phones where that message is in use.

Messaging - Callback

To leave a Callback Message when you hear busy or ringback tone:

• Press (MESSAGE) or press the key you have programmed as Callback.

To respond to a message waiting condition on your phone:

• To immediately call the extension that left the message, press

(MESSAGE).

31

Mitel 5330/5340 IP Phones – User Guide

To display information about the message:

5330 Phone:

1. Press the key that you have programmed as Messaging. The calling number and time of call are displayed.

2. Press the Message key for subsequent messages.

OR

• Press the Messaging softkey for Call and

Erase options only.

5340 Phone:

1. Press the key that you have programmed as Superkey. appears. time, and date of the call are displayed. through multiple messages.

Messaging - Cancel Callback

To cancel a Callback:

5330 Phone:

1. Lift the handset

2. Dial the appropriate feature access code.

3. Dial the number of the called station.

5340 Phone:

1. Press the key that you have programmed as Superkey. appears.

3. Press Msgs/Sent

Music

To turn Music on and off when the phone is idle, do one of the following:

• To toggle music on and off, press the key that you have programmed as Music or the

Music softkey.

When the Music feature is activated, the programmed Music key is illuminated.

Night Answer

The Night Answer feature allows you to route calls to an attendant or message at night.

To enable/disable Night Answer:

5330 Phone:

1. Using Superkey, program a Night Answer

feature key (See page 16 for instructions to

program keys using the Superkey.)

2. Press the key that you have programmed as Night Answer. When enabled, the key is illuminated.

5340 Phone:

1. Program a Night Answer feature key using the Settings key or Superkey. (See

page 15 for instructions to program keys

using the Settings key.)

2. Press the key that you have programmed as Night Answer. When enabled, the key is illuminated. disable. disable.

32

Mitel 5330/5340 IP Phones - User Guide

Override (Intrude)

When you dial a number whose owner has enabled Make Busy, your phone displays a message indicating that the line is busy. You have the option to override this setting.

To use Override when you encounter a busy tone:

1. Press the key you programmed as Override.

2. Wait for an answer.

Paging

To use Paging:

3. Dial the Paging zone number (if required).

4. Make the announcement.

Record a Call

This feature uses your voice mail system to record your telephone conversations.

Note: You may be required by law to inform the other party that you are recording the conversation. For specific instructions, consult your system administrator.

To start recording while on a 2-party call:

Note: Your system may be programmed to automatically begin recording external calls when you or the other answers.

To control recording, do one or all of the following:

• To pause recording, press the Pause softkey.

• To resume recording after pausing, press the Resume softkey.

• To stop a recording without saving it, press the Erase softkey or (CANCEL).

• To stop and save a recording, press the Save softkey.

Putting the call on hold saves the recording; taking the call off hold starts a new recording.

Depending on system programming, hanging up or pressing key, may also save the recording.

(TRANS/CONF) or a DSS

To listen to a recording:

1. Lift the handset.

2. Access your voice mailbox.

3. Follow the prompts to retrieve the recording.

33

Mitel 5330/5340 IP Phones – User Guide

Reminder

Note: The Reminder feature will not work if Auto Answer is enabled on your phone.

5330 Phone:

1. Press the key that you have programmed as Superkey.

5340 Phone:

1. Press the key that you have programmed as

Superkey.

2. Press More until Reminder appears.

Reminder" appears and then press Yes.

3. Enter the time and press the AM or PM softkey.

3. Press Reminder

4. Enter the time and press the AM or PM softkey.

To view/change and/or cancel a pending Reminder:

5330 Phone: 5340 Phone:

1. Press the key that you have programmed as

Superkey.

1. Press the key that you have programmed as

Superkey.

2. Press the No softkey until "Timed

Reminder?" appears and then press Yes.

2. Press More until Reminder appears.

3. Do one of the following:

• To change the Reminder, enter the new time and press Save.

• To cancel the Reminder, press Cancel.

• To exit without changing the Reminder, press Superkey

3. Do one of the following:

• To change the Reminder, enter the new time and press Save.

• To cancel the Reminder, press Cancel.

• To exit without changing the Reminder, press Superkey

To acknowledge a Reminder when your phone rings once:

Press the Acknowledge softkey.

Speed Call

Speed Call is an application that allows you to dial a specific number with one key press. You must program Speed Call on a programmable key. For information about programming this key,

see Programming Speed Call on page 16.

To make a Speed Call:

• Press the key that you have programmed as Speed Call.

34

Mitel 5330/5340 IP Phones - User Guide

Trunk Flash

The Trunk Flash feature allows you to access Centrex features (if available) while you are talking on an outside call.

To flash a trunk while talking on an outside call:

1. Press the key you have programmed as Flash.

Note: You can program a key to single flash or double flash.

2. Wait for dial tone.

3. Dial the Centrex feature access code.

Using Your Phone With The 5310 IP Conference Unit

Your phone uses the 5310 IP Conference Unit for conferencing. You use the Conference

Controller to turn the conference unit off or on, to adjust the volume or to put the conference unit into Presentation mode. You can only run one Conference Controller session at a time. If the

5310 Conference Unit is not connected to your phone, the Conference Controller application is not available.

Access the Conference Controller

To access the Conference Controller:

2. Press the key you have programmed to the Conference Unit application.

Turn the conference unit on and off

1. Verify that the conference unit is connected to your phone.

2. Access the Conference Controller.

3. Press Turn On/Turn Off. While the Conference Unit is on, the icon shows in the phone status line.

Adjust the conference unit volume

• Press Volume Up or Volume Down.

Place the conference unit in Presentation mode

Presentation Mode is used when only one individual is speaking to a group. If another member in the group wishes to speak, you must disable Presentation Mode. Presentation Mode minimizes extraneous noise.

To place the conference unit in Presentation mode:

Exit the conference controller

To exit the conference controller:

Mute the conference unit

To mute the conference unit so that conversation in the meeting room cannot be heard by individuals being conferenced:

35

Mitel 5330/5340 IP Phones – User Guide

Using your Phone with Cordless Module & Accessories

The cordless handset and cordless headset provide users with the capability to move around within their own office or adjacent offices while using the telephone.

Both cordless devices connect to your IP telephone through the cordless module, which attaches to the back of the phone. The cordless headset rests and recharges in a headset cradle that attaches to the side of the telephone. The cordless handset recharges in the handset cradle.

The Cordless Devices Application (see page 45) provides access to the configuration settings

and information screens that apply to the cordless module and accessories.

Note: Since only one module type can be attached to the phone at any given time, you can not use a Programmable Key Module (PKM) when the Cordless Module is attached.

CAUTION: Attempting to remove the back plate on the telephone to install the Cordless

Module before disconnecting the telephone’s power supply may damage the telephone.

For information about installing the Cordless Module, see the Cordless Module and

Accessories Installation Guide for Mitel 5330/5340 IP Phones available at Mitel OnLine.

Figure 1. Cordless Module and Accessories on 5300 Series Phone

36

Mitel 5330/5340 IP Phones - User Guide

Figure 2. Rear view

Elements of Your Cordless Module and Accessories

Feature (See Figure 1)

1) Cordless Module

Function

Attached to the back of the phone, the module contains a Light Emitting Diode (LED) indicating that a cordless device is in use; also indicates the state of pairing between the module and a cordless device.

2) Cordless Headset

3) Cordless Headset Charging Cradle

Cordless hands free operation for calls. If you are using the cordless headset, you do not need to use the handset.

Provides power to recharge the cordless headset battery.

4) Cordless Handset Charging Cover

5) Cordless Handset

Feature (See Figure 2)

6) Cordless Module pairing button

7) Cordless Headset Cradle cable

Provides power to recharge the cordless handset battery. Replaces the cover supplied with the phone for corded handsets.

Cordless operation for handset calls. (You can transfer from the phone handset to the cordless headset at any time.)

Function

Initiates pairing between the Cordless Module and a cordless accessory.

Connects to the Cordless Module to provide power to the charging cradle.

37

Mitel 5330/5340 IP Phones – User Guide

Handset/Headset Combinations

The following combinations of corded and cordless headset and handset are supported on the

5330/5340 IP Phone:

• Corded handset only

• Corded headset only

• Corded handset and corded headset

• Cordless handset only

• Cordless headset only

• Cordless handset and cordless headset

• Corded handset and cordless headset

• Corded headset and cordless handset

Pairing the Cordless Module and Accessories

The cordless headset and handset are optional accessories, ordered separately. Before use, each must establish communication with the Cordless Module using a procedure called pairing.

Notes:

• An IP telephone can have only one cordless handset and one cordless headset.

• A cordless handset or headset can be paired with only one IP telephone at a time.

• Pairing a new cordless handset or headset with the IP telephone overwrites the configuration of any previous handset or headset.

• Pairing cannot be performed when the cordless device is already in use.

Pairing a Cordless Accessory with the Cordless Module

To pair a cordless accessory:

1. Ensure that the battery of the cordless device to be paired is at least partially charged.

2. Press and hold down the pairing button on the back of the Cordless Module (see Figure 2 on page 37) for 5 seconds to activate telephone pairing mode. The LED on the Cordless

Module blinks. The Cordless Devices application opens on the telephone and prompts you to “Press the pairing button on the cordless device now.

3. Press and hold down the hookswitch on the cordless handset or headset for 5 seconds to activate accessory pairing mode. Note: on the headset, the hookswitch is the grey portion on which the logo is displayed.

4. If the device has not been previously paired:

− The LED on the cordless accessory blinks. After a moment, the Cordless Devices application displays protocol, firmware, hardware, and IPEI information for the device to be paired. flashes. The Cordless Devices application confirms the pairing by displaying the paired device name and its battery level indicator.

5. If the device has been previously paired: process, a blue LED on the device flashes. The Cordless Devices application confirms the pairing by displaying the paired device name and its battery level

38

Mitel 5330/5340 IP Phones - User Guide indicator. At this point, you can press the key for the paired device to display the battery level, protocol, firmware, hardware, and IPEI information for the device.

To unpair a cordless accessory:

2. Press the device name that you want to unpair. The information screen for the selected device appears.

Otherwise, the accessory is unpaired, removed from the display, and can no longer be used to interact with the phone.

For more information about the Cordless Devices Application, see page 46.

Cordless Module LED Indicators

The Cordless Module has a blue light-emitting diode (LED) that indicates the current status of the

module (See Figure 1):

Blue LED

Solid

Function

Audio is active between the module and either the handset or headset.

Blinking

Off

Pairing mode is active or a firmware upgrade is in progress.

No audio is active.

Solid for 2 seconds Pairing is successful.

Blinking: LED is On and Off for equal amount of time

39

Mitel 5330/5340 IP Phones – User Guide

Using the Cordless Handset

The cordless handset provides office mobility, allowing you to make and answer calls while away from your desk. Replacing the standard corded handset, the cordless handset contains a rechargeable battery that charges in the handset cradle when not in use.

To use the Cordless Handset, you must pair the handset with the phone. For more information,

see Pairing the Cordless Module and Accessories on page 38.

Figure 3. Cordless Handset on 5300 Series Phone

Elements of the Cordless Handset

Feature Function

1) Cordless Handset LED

Blue: Light-emitting diode (LED) indicating the status of the handset.

Green: LED indicating the status of the handset battery.

2) Hookswitch Button

For more information see Cordless Handset LEDs on page

42

Lifting the handset from the cradle activates the handset. If the handset is already out of the cradle, pressing the hookswitch takes the handset off-hook. Pressing the hookswitch again returns it to on-hook.

Mute allows you to turn the microphone off during a call. 3) Mute button

4) Volume Up and

5) Volume Down buttons

Up and Down provide volume control for the ringer and handset/headset.

Note: The IP Phone deactivates the cordless handset when a corded handset is plugged in.

40

Mitel 5330/5340 IP Phones - User Guide

Answer a call

Do one of the following:

• Lift the cordless handset.

• If the handset is already out of the cradle, press the hookswitch button on the handset.

Hang up

Do one of the following:

• Replace the cordless handset in the cradle.

• Press the hookswitch button on the handset.

Dialing – Auto Dial Disabled

To dial a number with Auto Dial disabled:

1. Lift the handset or press the hookswitch.

2. Make the call using the dial pad, or press a programmed speed dial key on the phone.

Dialing – Auto Dial Enabled

To dial with Auto Dial enabled:

• To dial the predefined Auto Dial number, press the hookswitch on the cordless handset or headset.

To program Auto Dial, refer to “Using the Cordless Devices Application” on page 46.

Alerting Tones and LEDs

The cordless accessories provide the following alerting tones:

Feature Function

Mute key on cordless device ON/OFF 2-pitch tone occurs immediately. Reminder tone occurs 30 seconds after activation and then regularly until deactivated.

Mute key on Phone ON/OFF

No immediate tone. Reminder tone occurs 30 seconds after activation and then regularly until deactivated.

Low battery (within 10 minutes left)

Low battery (within 2 minutes left)

Out of range

3 beeps and 20 second pause repeated 3 times

3 rapid beeps and 1.5 second pause repeated 3 times

Repetitive 3-pitch tone until you are back in range.

The call remains established if you return within range within 10 seconds; otherwise the call is dropped.

Note: Audio indications are heard in the handset only when it is in use.

41

Mitel 5330/5340 IP Phones – User Guide

Cordless Handset LEDs

The handset has two LEDs:

• Blue – indicates the operational status of the handset

• Green – indicates the status of the electrical charge of the battery

LED

Color

Blue

LED State

Solid

Blinking

Winking

Off

Indicates

Handset is muted

Handset is in pairing mode

Active audio path between Handset and Module

• No audio path between Handset and Module OR

• Battery is dead

Green Solid

Blinking

Battery is fully charged

Battery is charging

Off When handset is cradled and the LED does not flash or illuminate, this indicates an absence of battery power.

During the first 30 – 60 minutes that the light is off, the battery may be trickle charging. If that is the case, the

LED will resume normal behavior within that 60 minute period. If the LED remains off for more than 60 minutes, then either the battery is no longer chargeable or there is a problem in the charging circuit.

Blinking: LED is On and Off for equal amount of time

Winking: LED is On for a short period of time and Off for a longer period

Checking Battery Level of Cordless Accessories

To check the battery level, do either of the following: beside the paired accessory. accessory. The battery level is displayed along with protocol, firmware, hardware, and

IPEI information.

Replacing Batteries in Cordless Accessories

Note: The cordless handset battery is not user-replaceable.

Viewing Cordless Accessory Information

To view cordless accessory protocol, firmware, and hardware information: accessory. The battery level is displayed along with protocol, firmware, hardware, and

IPEI information.

42

Mitel 5330/5340 IP Phones - User Guide

Using the Cordless Headset

The cordless headset offers the same capability as the cordless handset to make and answer telephone calls away from your desk while adding the convenience of hands-free operation.

When not in use, the cordless headset sits in the headset charging cradle.

To use the Cordless Headset, you must pair the headset with the phone. For more information,

see “Pairing the Cordless Module and Accessories” on page 38.

Elements of the Cordless Headset

Feature

1) Microphone

2) Boom arm

3) Link indicator (LED)

4) Volume control with mute switch

(button on the top of the headset)

5) Hookswitch button (the grey portion of the headset that displays logo)

6) Speaker

7) Headband

8) Ear hook

43

Mitel 5330/5340 IP Phones – User Guide

Answer a call

Do one of the following:

• Lift the cordless headset from the cradle.

• If the headset is already out of the cradle, press the hookswitch button on the headset.

Hang up

Do one of the following:

• Replace the cordless headset in the cradle.

• If the headset is already out of the cradle, press the hookswitch button on the headset.

Dialing – Auto Dial Disabled

To dial a number with Auto Dial disabled:

1. Lift the headset or press the hookswitch.

2. Make the call using the dial pad, or press a programmed speed dial key on the phone.

Dialing – Auto Dial Enabled

To dial with Auto Dial enabled:

• To dial the predefined Auto Dial number, press the hookswitch on the cordless handset or headset.

To program Auto Dial, refer to “Using the Cordless Devices Application” on page 46.

Headset Alerting Tones and LEDs

The cordless accessories provide the following alerting tones:

Feature Function

Mute ON/OFF

Mute key on Phone ON/OFF

2-pitch tone occurs immediately. Reminder tone occurs

30 seconds after activation and then regularly until deactivated.

No immediate tone. Reminder tone occurs 30 seconds after activation and then regularly until deactivated.

Low battery (within 10 minutes left)

Low battery (within 2 minutes left)

Out of range

3 beeps and 20 second pause

3 rapid beeps and 1.5 second pause

Repetitive 3-pitch tone until you are back in range.

The call remains established if you return within range within 10 seconds; otherwise the call is dropped.

44

Mitel 5330/5340 IP Phones - User Guide

Cordless Headset LEDs

There are two LEDs associated with the cordless headset:

• A blue LED on the headset indicates the headset status

• A green LED in the headset charging cradle indicates battery status

LED Color

Blue

(on headset)

LED State Indicates

Solid Headset mic is muted

Blinking

Winking

Solid for 2 seconds

Off

Headset is in pairing mode

Active audio path between Headset and Module

• Pairing successful OR

• New battery installed

• No audio path between Headset and Module OR

• Battery is dead

Green

(on cradle)

Solid

Blinking

Winking

Off

Battery is fully charged

Battery is charging

Indicates low voltage when headset is uncradled

When headset is cradled, indicates battery is not charging.

Blinking: LED is On and Off for equal amount of time

Winking: LED is On for a short period of time and Off for a longer period

Checking Battery Level of Cordless Accessories

To check the battery level, do either of the following: beside the paired accessory. accessory. The battery level is displayed along with protocol, firmware, hardware, and

IPEI information.

Replacing Batteries in Cordless Accessories

To replace headset battery:

1. Unclip the battery pack from the ear/head/neck piece.

2. Slide the battery pack off the headset.

3. Slide the new battery pack onto the headset. The blue headset LED indicator illuminates for two seconds to confirm successful battery replacement.

4. Re-clip the ear/head/neck piece to the battery pack.

Do not expose batteries to heat or puncture them. Dispose of the product and/or batteries according to local standards and regulations.

Note: The cordless handset battery is not user-replaceable.

Viewing Cordless Accessory Information

To view cordless accessory protocol, firmware, and hardware information: accessory. The battery level is displayed along with protocol, firmware, hardware, and

IPEI information.

45

Mitel 5330/5340 IP Phones – User Guide

Using the Cordless Devices Application

The Cordless Devices Application provides access to module information and pairing for hand- or headsets.

To access the Cordless Devices Application, do one of the following:

• Press a feature key you have programmed as the Cordless Devices Application key.

For information about programming feature keys, refer to

Programming Features On Your Keys on page 13.

Note: When the pairing button on the Cordless Module is pressed, or when the battery level of a cordless accessory is critically low, the phone will automatically open the Cordless Devices

Application.

Viewing Cordless Module Information

You can use the Cordless Module Application to view protocol, firmware, and hardware information about the module.

To view cordless module information

1. Access the Cordless Module Application.

Low Battery Level

When the battery of a cordless device reaches a near-critical level, the phone displays a warning.

Until the battery is recharged (or until it becomes fully discharged), the warning is repeated at each new call made using the Prime Line. To continue with a call while charging the cordless accessory, switch to speakerphone and then cradle the cordless accessory.

Auto Dial

When a Cordless Module is installed and at least one device is paired, the Auto Dial feature is available in the Settings menu. You can program a number that is automatically dialed when a cordless device hookswitch button is pressed.

To program an Auto Dial number:

Press .

the

or the

onscreen keyboard

, enter the auto dial number.

the

or the

onscreen keyboard

, enter the label.

46

Mitel 5330/5340 IP Phones - User Guide

To disable Auto Dial:

1. Press . when the feature is disabled.

• To re-enable, repeat steps 1 and 2 and then press Enable Auto Dial.

• To change Auto Dial information, press Edit Number and/or Edit Label.

Using a Cordless Device as a Remote Control

When not being used to talk, the cordless handset/headset buttons can act as a remote control device to change display contrast, volume, and mute settings on the host IP phone. For example, in a remote handsfree conference setting, the chairman can use the volume and mute buttons on a cordless device to adjust speaker levels and mute the microphone on an IP phone that is not within his reach. HTML applications may also make use of the cordless device buttons but functionality may differ among applications.

47

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Table of contents