Capital | LGSCR364B | Installation guide | Capital LGSCR364B Installation guide

USE AND CARE & INSTALLATION GUIDE
GAS SELF CLEAN
TABLE OF CONTENTS
LG features
3
Models
4-5-6-7
Warnings
Safety Practices / Electrical, General
8
9
Safety Practices / Cooking
10-11
Oven Parts Identification
12
Range Parts Identification
13
Using The Range-Top / Power Burners
Using The RangeTop
Using Your Oven
Using Your Oven - Self Clean Mode
Care And Maintenance
Care And Maintenance / locating Rating Plate
Troubleshooting
Installation Instructions
Table Of Contents
Service / Warranty
14
15-16-17
17-18-19-20
21-22
23
LGR SERIES
24
25-26
27
28
41
2
LG GAS RANGES FEATURES:
LGR SERIES
STAY-KOOL™ KNOBS
Our restaurant grade, die cast chrome plated metal knobs
feature bold red graphics for easy readings of settings, and plastic inserts
that stay cooler to the touch when using your range. Available in Black. (Red Available as accessory only)
POWER-FLO"' BURNERS
These versatile burners are the most advanced burners available in the industry. They allow from true simmering
to a powerful 17,000 BTUs. Not only are they powerful, but they are energy efficient also.
TRADITIONAL BBQ-GRILL
The Precision Gas Convection Ranges (Manual Clean), feature our exclusive BBQ-Grill w/ Tru-Sided stainless steel
channeling grates, that help reduce flare-ups by channeling the grease away from the burner.
The stainless radiant trays promote evenness of heat, which means no more cold spots.the burner
generates a powerful 18,000 BTUs. Plenty of performance to cook a vast array of cuisine, from juicy steaks, to vegetables.
THERMO-GRIDDLE
Our solid stainless steel thermostatically controlled griddle plate gives you precise control over the
griddle area. From 18,000 BTUs on 12" griddle sections.
INFRA-BROIL
Our gas infrared broiler beneath glass generates 18,000 BTUS
of power. And the radiant glass makes clean-ups a snap.
FLEX-ROLL OVEN RACKS (SELF CLEAN ONLY)
Our patented Flex Roll oven racks
provide the smoothest, most effortless range of
motion in any oven EVER manufactured!
3
LGR SERIES
30” MODELS
30” LGR MSELF-CLEAN MODELS
LGSCR304
LGSCR304
4
LGR SERIES
36” MODELSS
36” LGR MSELF-CLEAN MODELS
-
LGSCR366
LGSCR364G
LGSCR364B
LGSCR366
5
LGR SERIES
48” MODELS
48” LGR MSELF-CLEAN MODELS
LGSCR486G
LGSCR484BG
LGSCR486B
LGSCR488
LGSCR484BG
6
60” MODELS NOT AVAILABLE
LGR SERIES
7
WARNINGS!
WARNING! If the information in this manual is not
followed exactly, a fire or explosion may result
causing property damage, personal injury or death.






WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance
Do not touch any electrical switch
Do not use any phone in your building
Immediately call your gas supplier from a
neighbors phone. Follow the gas supplier's
instructions.
If you can not reach your gas supplier, call the
fire department
Installation and service must be performed by a
qualified installer, service agency or the gas supplier.
The appliance and its individual shutoff valve must
be disconnected from the gas supply piping
system during any pressure testing of that system
test pressures in excess of 5 psi (35 kpa).
The appliance must be isolated from the gas supply
piping system by closing its individual manual
shutoff valve during any pressure testing of the gas
WARNING! Disconnect Power before installing.
Before turning power ON, be sure that all
controls are in the OFF position.
IMPORTANT! Installation must conform with local
codes or, in the absence of local codes, with the
National fuel Gas Code, ANSI Z223.1/NFPA54.



Smother flames with a close fitting lid, or any
metal tray.
Turn OFF the burner. Be careful to prevent burns. If
the flames do not extinguish, immediately
evacuate and call the fire department
NEVER pick up a flaming pan. By doing so, you
may be seriously injury.





DO NOT use water or a wet dishcloth on
fire. A violent steam explosion will result.
Use a fire extinguisher only if:
You have CLASS ABC extinguisher and you
know how to operate it.
The fire is small and contained in the area
where it started.
The fire department has been called.
You can fight the fire with your back to the
exit.
FOR YOUR SAFETY! If You Smell Gas:
Shut off gas to the appliance. Extinguish any
open flames. If odor persists, immediately call
your gas supplier.
This appliance is designed for easy of
installation and operation. However, we recommend that you read all sections of this manual
before installation and that your range is installed
by an approved gas installation technician capable of reviewing and performing the manufacturers
installation checklist included in your information
packet.
The installation of appliances assigned for
manufactured (mobile) home installation must
conform with the Manufactured Home Construction and
Safety and Safety Standard, Title 24 CFR, Part 3280
or, when such standard is not applicable
Standard for Manufactured Home Installations,
ANSI/NCSBCS A225.1, or with local codes as
The installation of appliances designed for
Recreation Park Trailers must conform with state
or other codes or, in the absence of such codes,
with the standard for Recreational Park Trailers,
ANSI A119.5.
The appliance, when installed, must be electrically grounded in accordance with local codes
or, in the absence of local codes, with the
National
LGR SERIES
Electrical Code, ANSI/NFPA 70
WARNING! If the information in this manual is not
followed exactly, a fire or explosion may result,
causing property damage, personal injury or death.
Please read the installation, operating and maintenance instructions thoroughly before use.
CAUTION! When connecting the unit to propane
gas, make certain the propane tank is equipped
with its own high-pressure regulator in addition to
the pressure regulator supplied with the range.
The pressure of the gas supplied to the appliance
must not exceed 14" (34.57 mB) water column
from the propane gas tank to the pressure reguCAUTION! Do not store or use gasoline or any
other flammable liquids in the vicinity of this or any
other appliance.
PLEASE RETAIN THIS
MANUAL FOR FUTURE
REFERENCE!
PLEASE NOTE:
In the Commonwealth of Massachusetts, gas connection must be performed by a licensed plumber
or licensed gas fitter.
IMPORTANT!: For fire safety and correct operation
a back guard must be installed on all ranges prior to
use! All ranges are shipped with a standard 3" Island
Trim which is compatible with non-combustible back
wall installations ONLY! If desired or if the minimum
distance to a combustible back wall in not met (see
Fig. 2A) one of two additional back guards heights
may be ordered and installed (Low Back – 9", or
High Back – 18"). Refer to the Installation Instructions
accompanying this appliance for assembly instructions
8
LGR SERIES
SAFETY PRACTICES / ELECTRICAL, GENERAL
ELECTRICAL SAFETY:
Electrical Requirements and Grounding Instructions
*It is recommended that a dedicated circuit servicing
this appliance be provided.

NOTE: ALL MODELS.
IN CASE OF AN ELECTRICAL FAILURE
If for any reason a gas control knob is turned ON and
there is no electric power to operate the electronic
igniters on the range burners, turn OFF the gas
control knob and wait 5 minutes for the gas to
dissipate before lighting the range burner manually.

To light the range burners manually, carefully hold
a lighted match to the burner ports and turn the
gas control knob to Hl. During a power failure, you
can manually light the standard range burners
only, but each must be lit with a match.
Note: For LGR Gas Ranges, the gas oven, grill,
Thermo-griddle'"' and infrared oven broiler burners
CANNOT be lit manually during a power failure.
WARNING! Do not under any circumstances cut
or remove the separate ground wire or the third
(ground) prong from the power cord plug.
PLEASE READ CAREFULLY:
All gas range models require an electrical circuit rated
at 120 volts, 60 Hz., and 20 Amps. (VERIFY) For
personal safety, this appliance must be connected to
a properly grounded and polarized electrical power
supply. Always disconnect the electrical plug
from the wall receptacle before servicing this unit.
See Installation Instructions for electrical requirements and grounding instructions.
It is the personal responsibility and obligation of
you, the user, to have this appliance connected to the
electrical power supply in accordance with the National Electrical Code and/or applicable local
codes and ordinances by a qualified electrician.

GENERAL SAFETY:
Your new range has been designed to be a
safe, reliable appliance when properly installed,
used and maintained. If not properly used, it could
be dangerous. Read ALL the instructions in this
Use and Care Guide carefully before using this range.
WARNING! These precautions will reduce the
risk of burns, electric shock, fire, and injury to
persons. Use extreme care when using this
restaurant caliber range as this appliance
provides intense heat and can increase accident potential.



Safety precautions must be followed when
using any kitchen appliance.
Insure proper installation and servicing.
Follow the installation instructions provided
with this product. Have the range installed
and grounded by a qualified technician.
Have the installer show you where the gas
supply shut off valve is located so that you
know how and where to turn off the gas to the
range.
In the event a burner goes out and gas escapes,
open a window or door immediately. DO NOT
attempt to use the range until the gas has had time
to dissipate. Wait at least 5 minutes before using
the range.
DO NOT repair or replace any part of the appliance
unless specifically recommended in this manual.
All other servicing should be referred to a
qualified technician.
Children SHOULD NOT be left alone or unattended
in an area where appliances are in use. They
should never be allowed to sit or stand on any part
of the appliance.
CAUTION! Do not store items of interest to children above the range or behind it. If children
should climb onto the appliance to reach these
items, they could be seriously injured.


If you smell gas, your installer has not done a proper
job of checking for leaks. If the connections
are not perfectly tight, you can have a small
leak and therefore smell of faint gas odor.
Finding a gas leak is not a "do-it-yourself"
procedure. Some leaks can only be found with
the burner control in the "ON" position and a
qualified service technician must do this.


NEVER use any part of the range for storage.
Flammable materials can catch fire and plastic
items may melt or ignite.
If the range is near a window, be certain the
curtains do not blow over or near the range burners, griddle or broiler section; they could catch
fire and cause serious damage and injury.
DO NOT USE WATER ON GREASE FIRES! Turn
appliance off and smother fire with baking soda
or use a dry chemical or foam-type extinguisher.
9
LGR SERIES
SAFETY PRACTICES / COOKING
 NEVER let clothing, potholders, or other flammable
materials come into contact with or too close to any
element, burner, or burner grate until it has cooled.
Fabric may ignite and result in personal injury.
COOKING SAFETY:
 USE ONLY DRY POTHOLDERS. Moist or damp
potholders on hot surfaces may cause burns from
the steam. Do not use a towel or other bulky cloth
in place of potholders. Do not let Potholders
touch hot elements, hot burners, or burner grates.
 FOR PERSONAL SAFETY, wear proper apparel.
Loose fitting garments or hanging sleeves should
never be worn while using this appliance. Some
synthetic fabrics are highly flammable and should
not be worn while cooking.
 DO NOT use aluminum foil as a shield against
food spills or drippings around the burners or
control panel area. This could obstruct the flow of
combustion and ventilated air. This can damage
the finish of the range.
WARNING! This appliance is for cooking!
Based on safety considerations, never use
the range to warm or heat a room. Such use can
damage the range.
 DO NOT TOUCH THE BURNER GRATES OR THE
temperature changes. Use only on low or medium
heat settings according to the utensil manufacturer's
directions.
A buildup of pressure may cause the container to burst
 DURING COOKING, set the burner control so that
OFF and the range is cool before using any type of
aerosol cleaner on or around the range. The chemical that produces the spraying action could, in the
presence of heat, ignite or cause metal parts to
corrode. Only an authorized service technician
should perform Service. Technicians must disconnect the power supply before servicing this unit.
 USE CAUTION to ensure that drafts like those
from forced air vents or fans do not blow flammable
materials toward the flames or push the flames so
that they extend beyond the edges of the pot.
 ALWAYS use utensils that have flat bottoms, large
enough to cover the burner. The use of undersized
utensils could expose a portion of the flame and
may result in ignition of clothing. It is also a waste
of gas.
 TO MINIMIZE BURNS, ignition of flammable
materials and unintentional spills, position handles
of utensil inward so that it does not extend over
adjacent work areas, cooking areas or the edge
of the range.
 CLEAN THE VENTILATOR HOOD and filters
above the range frequently so grease deposits
from cooking vapors do not accumulate on them.
 IN CASE OF FIRE or when intentionally using
"flaming" liquor or other spirits on the range, follow
hood manufacturer's instructions.
 INSTALL A SMOKE DETECTOR in or near the kitchen.
 TURN THE KNOB CONTROL TO OFF if a burner
goes out and gas escapes. Open a window or door.
DO NOT attempt to use the range until the gas has
 HOLD THE HANDLE of the pan to prevent
had time to dissipate.
movement of the utensil when stirring food.
 DO NOT USE the BBQ grill top section for
cooking excessively fatty meats or products that
promote flare-ups.
 NEVER leave the range unattended when using
before attempting to handle it. Avoid letting grease
deposits to collect. Clean after each use.
ceramic, ceramic earthenware or other glazed
utensils are suitable for range use. Other types of
utensils may break with sudden
 BE SURE ALL RANGE CONTROLS ARE TURNED
the flame heats only the bottom of the pan and
does not extend beyond the bottom of the pan.
 GREASE IS FLAMMABLE. Let hot grease cool
 ONLY certain types of glass, heat proof glass-
Avoid steam bums; do not use a wet sponge or cloth to
clean the range while it is hot. Some cleaners produce
noxious fumes if applied to a hot surface. Follow
directions• provided by the cleaner manufacturer.
 DO NOT HEAT UNOPENED FOOD CONTAINERS.
IMMEDIATE SURROUNDING AREAS adjacent to
the burners. When in use these areas may become
hot enough to cause burns.
high flame settings. Boil-overs cause smoking
and greasy spills that may ignite. More importantly,
if the burner flames are smothered, unburned
gas will escape into the room. See inside front
cover regarding gas leaks.
 CLEAN THE RANGE-TOP SECTION WITH CAUTION.
WARNING! To reduce the risk of tipping of the
appliance, it must be secured by a properly installed
anti-tip device. Verify that the anti-tip device
is engaged per installation instructions (note:
anti-tip device is required on all gas ranges.)
SEE PAGE 38
 KEEP BURNER PORTS CLEAN. This is essential for proper lighting and maintenance of the
burners. It is necessary to clean the burner
ports when there is a boil over or when the
burner does not light though the electronic igniters
click.

When using the oven: DO NOT touch the
interior s u r f a c e s o f t h e o v e n o r t h e
e x t e r i o r a r e a immediately surrounding
the door. Interior oven surfaces become
hot enough to cause burns. The heat deflector, which deflects heat away from the
range and the trim on the top and sides
10
SAFETY PRACTICES / COOKING
 Place oven racks in desired position while oven is
cool. If a rack must be removed while the oven is
hot, do not let the potholders contact the hot
infrared burner.
 Us e car e w hen opening t he oven door ; let
hot steam or air escape before removing or
replacing foods.
 DO NOT remove the door gasket.
It is essential for a good seal during baking.
 BE CAREFUL not to damage the glass covering the
infrared broiler in the gas oven. If the glass is damaged,
air can enter the distribution box behind the glass, possibly resulting in an explosion.
 In the event that personal clothing catches fire,
DROP AND ROLL immediately to extinguish flames.
 DO NOT obstruct the path of combustion or ventilation air.
 For safety reasons and to avoid equipment damage,
never sit, stand, or lean on any part of the range.
 S e r v i c e s h o u l d o n l y b e p e r f o r m e d b y a quali-
LGR SERIES
1. Remove all packing materials and labels from your
appliance. If the installer has not set up your appliance,
please do it before using it.
2. Place the oven racks in the proper position before turning on the oven.
For correct rack position, check your recipe. The
most frequently used position is number 2. The
rack positions are numbered from the bottom to the
top as in the floors of a building.
CAUTION! Do not use aluminum foil to cover
the oven racks or to line the oven. Heat can be
trapped beneath the foil, this can cause damage
to the oven and food may not cook correctly.
3. Before BAKING and BROILING
Turn on the oven and broiler burners one at a
time for 20 to 30 minutes each. This burns off the
manufacturing oils used by the factory. Turn the
oven burner on to 450°F and then the broiler
burner on to "Broil". Be sure to turn on the
ventilator above your range while these burners
are on, as there will be an odor.
fied, Factory Authorized Service Technician. Technicians must disconnect the power supply before servicing
this unit.
CALIFORNIA PROPOSITION 65 WARNING:
The burning of gas cooking fuel generates some
by products which are on the list of substances
which are known by the State of California to
cause Cancer or reproductive harm. California law
requires business to warn customers of potential
exposure to these substances. To minimize
exposure to these substances, always operate this
unit according to the instructions contained in this
booklet and provide good ventilation to the room
when cooking with gas.
11
OVEN RANGE PART IDENTIFICATION
LGR SERIES
1.Large Oven
2.Oven Thermostat Sensing Bulb
3.Convection Baffle
4.Convection Fan (center back
wall of oven can behind baffle)
5.Oven Light
6.Broiler Burner (behind glass)
7.Door Lock (only on self clean models)
8.Heat Shield
9.Small Oven
10.Oven Gasket
12
LGR SERIES
RANGE PARTS IDENTIFICATION
1.Burner 17k BTU
10.Knobs
2.Griddle Plate
11.Drip Pan Handle
3.Griddle Flue Cover
12.Oven Door Handle
4.BBQ-Grill
13.Door Panel
5.Island Trim
14 Small Door Panel
6.Cast Iron Grate
15 Kick Plate
7.Bull Nose
16.Ajustable Leg
8.Indicating Lights
17.Ajustable Caster
9.Switch (Light & Fan
13
LGR SERIES
USING THE RANGE-TOP BURNERS
POWER-FLO™ BURNERS
Your new gas range is equipped with the latest in
burner technology. The Power-FIo™ burners are
designed for maximum control and the precise use
of heat where it matters most. The large top-cap
spreads the simmer flame over the bottom of a pot
to avoid too much heat being concentrated in the
center, thus avoiding burning of delicate sauces.
The flame ring at the bottom stabilizes the main
ports so as to achieve higher heat and maintain
proper combustion of the burners, leading to greater
efficiency and no yellow tips. It is always ON when
the burner is in use. The burner should never be
operated if the cap is not in place.
All the range-top burners have electronic spark
ignition to eliminate continuously burning pilots.
When the main burner flame is blown out, it will relight.
SIMMERING
Your new range-top has exceptionally low simmering
capabilities. The large cap serves as a heat difuser to
spread out the heat to avoid having a center hot spot.
keep in mind that because of the high heat capacity
of the outer burner, and the mass of the burner grates
(they retain heat longer than lighter, conventional
grates), some foods may continue to cook by retained
heat after the burner has been turned off.
When using the simmer feature, turn the main
burner knob down to the simmer position.
Should a strong draft or boil over extinguish
the simmer flame it will relight automatically as
the main burner would.
ELECTRONIC IGNITERS
If a burner does not ignite, listen for the clicking
sound. If the burner does not click, TURN
OFF THE BURNER. Check the circuit
breaker for a blown fuse or a tripped circuit
breaker. If the igniter still fails to operate, see
page 25 "Troubleshooting", "Before calling For
Service".
the appliance may cause an orange flame. This
will disappear with use.
FLAME HEIGHT
NOTE. If you are using propane gas, a slight pop
flash may occur at the burner ports a few seconds
after the burner has been turned "off". This
"extinction pop" is normal for propane gas.
BURNER EFFICIENCY AND
FLAME CHARACTERISTICS
It is necessary to keep the burner ports and the
igniters -clean for proper lighting and efficient
performance of the range-top burners.
The burner flame should burn completely around
the burner with no excessive noise or lifting. The
flame should be blue in color and stable with no
yellow tips.
An improper air—gas mixture may cause either a
burner flutter or a yellow tipped flame. A technician .should adjust the flame. During initial use,
foreign particles in the gas line, or dust in the air around
The correct height of the flame mainly depends on
the size of the bottom of the cooking utensil.
Following are some basic rules for selecting
flame height.
For safety reasons the flame must never extend beyond
the bottom of the cooking utensil. Never allow flames to
curl up the s i d e o f t h e p a n . Utensils which conduct heat slowly (such as glass-ceramic) should be
used with medium to low flames. If you are cooking
with a large pot, a larger flame can be used.
Proper Flame Height
CORRECT
WRONG
14
USING THE RANGETOP
BURNER SETTINGS
The rangetop burner valves have infinite settings and there are no fixed positions on the
control knobs between HI and SIMMER. To
turn the rangetop burner on, push in the
control knob and turn it counterclockwise
to the "LITE" position. An audible clicking
sound will be heard. When the gas has
been ignited by the electronic spark igniter,
turn the knob to the desired setting.
finer department stores, specialty cooking shops, or
restaurant supply stores. If using regular cookware
be very careful if pans have plastic handles, as our
Power Flo burners can melt or bubble the handles.
THE CONTROL KNOBS
The control knobs are readily associated with
the burners they control. The RANGETOP control
knobs are labeled in front of the burners. The
oven control is placed slightly higher than the
other control knobs. This is due to the physical size
of the commercial type thermostats used on the product.
CAUTION!
Use extreme care when placing the grill
components into the grill compartment. Avoid
hitting the ceramic igniter that could break,
preventing operation of the grill.
 Do not leave the grill unattended while in use.
 Do not use charcoal briquettes, ceramic plates, or
Note: If the Igniter continues to click after the
burner has been lit, turn the knob to a setting
other than LITE, or HI. If the problem still persists,
please call our Service Hotline at 866-402-4600.
CAUTION! When turning on any RANGETOP
burner, be sure to stop at the "LITE" position
before turning the burner to a flame setting for
cooking. If the burner is not lit and it is turned
beyond the "LITE" position, to HI, MEDIUM, or
LO, there will be a burst of flame when the burner
does light. This could cause burns or damage to
the surrounding counter top.
coals of any kind.
After removing all packaging materials, check to
be certain that the grill components are correctly
assembled in the grill box. The grill grates and
the burner are assembled in the grill box from
the factory.
Note: Your grill racks are constructed from stainless steel
and electro-polished to achieve a brilliant finish. After
the first use, discoloration will occur This is natural and
unavoidable.
LGR SERIES
All the range-top burners have electronic spark ignition
to eliminate continuously burning pilots. When the main
burner flame is blown out, it will relight. Also each
burner has its own ignition module. If one module fails
all others will continue to work and you are not inconvenienced.
If a burner does not ignite, listen for the clicking
sound. If the burner does not click, TURN OFF
BURNER. Check the circuit breaker for a blown
fuse or a tripped circuit breaker. If the igniter still
fails to operate, please call our customer service department at 1-866-402-4600.
Note.
If you are using propane gas, a slight pop or flash may
occur at the burner ports a few seconds after the burner
has been turned "off". This "extinction pop" is normal for
propane gas.
COOKING ON THE GRILL
The burner should light within approximately 45 seconds.
 Preheat the grill for approximately 5 minutes
minimum. The hot grill sears the food, sealing in
the juices.
 The longer the preheat time, the faster the meat
browns and the darker the brand marks.
 Grilling requires high heat for optimum results.
High heat is necessary for searing and proper
browning. Most foods are cooked at medium
heat settings for most of the cooking time.
However, when grilling large pieces of meat or
BURNER GRATES
The burner grates are a cast iron.
PROPER COOKING UTENSILS
For best results we recommend using Professional
Cookware. These types of utensils can be found at your
15
LGR SERIES
USING THE RANGETOP
poultry, it may be necessary to turn the heat to
a lower setting after the initial browning. This
cooks the food through without burning the outside
 Foods cooked for a long period of time or basted
with a sugary marinade may need a lower heat
setting near the end of the cooking time
 After grilling and the food has been removed, turn
the knob to HI and burn off any excess grease that
may have accumulated on the burner
 Use a brass wire brush, dipped in hot water;
be necessary to turn the heat to a lower setting
after the initial browning. This cooks the food
 Foods cooked for a long period of time or basted
with a sugary marinade may need a lower
heat setting near the end of the cooking time
 After grilling and the food has been removed,
turn the knob to HI and burn off any excess grease
thatmay have accumulated on the stainlesssteelradiant
 Use a brass wire brush, dipped in hot water, to
loosen food particles from the grate
toloosen food particles from the grate
 When the grill has cooled, clean the drip
tray,and compartment
 If ash is particularly thick and impedes the airflow
of the burner and prevents safe and efficient lighting
of the burner, when burner is cool, use a handheld
vacuum cleaner and quickly vacuum away the ash.
COOKING ON THE STAINLESS STEEL BBQ
 Preheat the grill for approximately 10 minutes
minimum. The hot grill sears the food, sealing in
the juices. The longer the preheat time, the faster
the meat browns and the darker the brand marks
 Grilling requires high heat for optimum results.
High heat is necessary for searing and proper
browning. Most foods are cooked at higher heat
settings for most of the cooking time. However;
when grilling large pieces of meat or poultry, it may
 When the grill has cooled, clean the drip tray,
radiant, heat deflector and compartment. Wipe
the U-shaped burner with a damp cloth.
CAUTON!
 Use extreme care when placing the grill components
into the grill compartment. Avoid contacting
the ceramic igniter that could break, preventing
operation of the grill.
 The grill must be assembled as shown. The drip
tray heat shields must be in place, and the burner
must be properly positioned relative to the gas
supply. Incorrect assembly of the grill may result in
unsafe or hazardous conditions during operation
Note: Your grill racks are constructed from stainless
steel and electro-polished to achieve a brilliant finish.
After the first use‘ discoloration will occur. This is
GRILLING SUGGESTIONS
 Trim any excess fat from the meat before cooking.
FATTY MEATS increase the likelihood of flare-ups.
Cut slits in the remaining fat around the edges at
2" (51 mm) intervals
 Brush on basting sauces towards the end of cooking
 Add seasoning or salt after grilling. Early salting
dries out meat
 Use a spatula or tongs instead of a fork to turn the
meat. A fork punctures the meat and lets the
juices flow out
 After the juices begin to bubble to the surface,
turn the meat only once. This helps keep the
juices in the meat
 Some pieces of meat and poultry cook faster than
others. Move those pieces to the cooler area of the
grill until the rest have finished
 The doneness of meat is affected by the thickness
of the cut. Chefs say it is impossible to have a rare
doneness with a thin cut.
 Do not leave the grill unattended while in use
 Do not use charcoal briquettes, ceramic plates, or
coals of any kind.
After removing all packaging materials, check to
be certain that the grill components are correctly
assembled in the grill box. The grill grates, stainless
steel radiant and the burner are assembled in the
grill box from the factory. Please see below for
correct parts associated with the grill box.
TRUSIDE ™ GRILL RACKS
 The grill racks are double sided, two position
grates, constructed of pure stainless steel. Use
the concave side (channels up) for meats of
higher fat content (Steaks, hamburgers, sausage
patties, etc.); use the convex side (channels
down) with foods of lesser fat content (fish,
vegetables, fruits, etc.)
WARNNG! Do not leave the BBQ section
unattended while cooking!
16
USING THE RANGETOP/USING YOUR OVEN
HANDLING EXCESSIVE FLARE-UPS





The intense heat needed for grilling may
also cause flare-ups, due to grease and basting sauces dripping on the hot radiants.
If flare-ups occur, use a long handled spatula
to move the food to another area of the grill.
Should flare-ups become excessive, remove
the food from the grill and turn off the burner
Excessive flames occur when cooking meat
with high fat concentration, i.e. 30% ground
beef, untrimmed steaks, lamb chops, etc.
Be cautious when turning meat over, and
never PLOP the meat on the grates.
COOKING ON THE THERMO-GRIDDLE
Description:
 The built in griddle is made of non rusting
3/8" thick stainless steel. This produces a surface
that is easy to clean and never rusts.
 The griddle has a aluminized steel straight tube
burner that is lit by a hot surface igniter. The griddle should pre heat for five to ten minutes.
 A chopping block is available as an accessory and
purchased separately. It is sized to fit on top of the
griddle surface when griddle is not in use.
 The burner is rated at 18,000 BTU/HR.
CONTROL KNOB
 The griddle is thermostatically controlled with temperatures marked on the knob from 150 degrees F
to 500 degrees F
 There are no fixed settings on the knob.
 Press and turn the knob counterclockwise to the temperature setting.
PREPARING THE GRIDDLE
 The griddle must be level or tilted slightly
forward for optimum performance. The griddle should have been leveled during installation.
 PRIOR TO USE, It Is NECESSARY to wash
the griddle plate with warm soapy water then
rinsed with clear water. The griddle may be
used without butter, margarine, or oil. However, a very small amount may be used to
flavor foods.
COOKING ON THE GRIDDLE
 Check that the grease tray is tucked under the
griddle plate overhang.
 Turn the knob to the cooking temperature to preheat the griddle.

Preheat 5-10 Minutes.
 Add butter, margarine, shortening or oil for more
flavor: Add food and cook!
LGR SERIES
with bake and broil burners typical of those
used in restaurants. The oven broiler burner is
18,000 Btu/hr and the oven baking burner is
30,000 Btu/hr.
ELECTRIC GLOW IGNITER
The oven bake and broil burners are equipped with
an electric glow igniter and safety system which
lights the gas. There will be a delay after the control
knob has been turned on to when you actually hear
gas arrive at the burner. The burner will ignite after
the gas reaches the burner, sometimes this can take
as long as 45 seconds.
USING CONVECTION BAKE AND REGULAR BAKE
TO SET THE OVEN FOR CONVECTION BAKE
AND REGULAR BAKE
Decide if you are going to use CONVECTION BAKE or
REGULAR BAKE. These cooking modes are for baking
or warming: using one, two, three or four racks. If you
are going to use Regular Bake turn the oven control
knob to the temperature used in the recipe.
To use Convection Bake, simply press the
CONVECTION Button located on the front
panel to start the Convection Fan.
OVEN USE
GENERAL (Only on large self clean oven).
Your large new oven can be used in 6 cooking models convection bake, regular bake, convection broil, regular broil, convection broil, rotisserie, regular-broil rotisserie. To help you
decide which way to cook your food read this information
first. Remember this is a new oven and the thermostat has
been checked for accuracy. Your old oven had a thermostat that
over the years got a little cold. Check your recipes for the correct time and temperature and don't use the old time or temperature you were using to compensate for your old oven
being off temperature.
SMALL OVEN REGULAR BAKE ONLY
BURNERS
Your new Culinarian Series— range is equipped
CONDENSATION
During any cooking process there is a certain
amount of moisture that evaporates from the
food. The amount of moisture that condenses
on the oven depends on the moisture content of
the food. The moisture will condense on any
surface that is cooler than the inside of the
oven, such as the control panel or the top of the
CONVECTION BAKE
Convection Bake is baking with a fan at the back
of the oven circulating the hot air in a continuous
pattern around the food. This circulating hot air
heats and browns the surface of the food more
effectively than in a standard oven. This allows
most foods to be cooked at lower oven temperature or in less time,
17
USING YOUR OVEN
if baked at the regular temperature. The air is recirculated and reheated. Uncovered, longer cooking
foods such as large pieces of meat or other foods
that can be cooked in low sided baking utensils or air
leavened foods, are where you will see the most savings in cooking time. Using multiple rack at the same
time will achieve a good time saving, as you can cook
more food at the same time. The number of recipes
requiring preheating of the oven is reduced considerably
because the heat reaches the food faster as the hot air
circulates around the food.
FOODS SUITABLE FOR CONVECTION BAKE
Air Leavened Foods (angel food cake, soufflés,
cream puffs, meringue shells)
Appetizers
Breads
Main Dishes
Oven Meals (1 to 4 racks)
Cookies
Pies
Poultry
Roasts
CONVERTING RECIPES TO CONVECTION BAKE
Low sided baking utensils will provide the best results, as
the hot air can reach all sides of the utensil easier. The
oven temperature can be left the same as the recipe
and the food cooked a shorter period of time. The
temperature can be lowered 25°F to 50°F and the
food will probably take the same length of time to
cook as the recipe states. If you find that food is adequately browned on the outside, but not done in the
center, lower the temperature another 25°F and add
to baking time. When reducing the temperature always check the food for doneness, a minute or two
before the minimum time stated in the recipe, as
time can always be added. Some recipes will cook
faster than others. There is no way to predict exactly
how long each recipe will take when you convert it to
convection.
Convection will be easier to use after you have used
it a few times as you will begin to understand the way
it bakes.
SELECTING UTENSILS FOR CONVECTION BAKE
Cooking by convection does not require any specially
designed baking utensils. You probably have many
utensils in your kitchen that are suitable to use. When
choosing a baking utensil, consider the material, the
size and shape as they all affect the baking time, the
appearance of the finished product.
Metal bake ware (aluminum, steel and cast iron) all
result in the fastest cooking time and the best end
product. Aluminum pans work best for all types of
baked goods. For the best browning, use a pan with a
dark or dull finish that absorbs heat, when baking
pies and breads. A shiny finish works best for cakes
and cookies, since it reflects some of the heat and
provides a tenderer surface. Cookie sheets with only
one lip will give the best results, as the heated air can
circulate all around the sides of the food.
For roasting, use bottom of the broil pan and elevate the
meat on a metal roasting rack. Glass-ceramic or glass
utensils do not conduct heat as well as metal, but they
can be used. Use them for foods that do not require a
dark brown crust or crisping, such as soufflés.
Baked items cook more quickly and evenly if they are
individually smaller in size, i.e. two or three small foods do
better than one large piece. When single food items are
baked, always center the rack. If several foods are being
baked, space them evenly on the racks.
RACK POSITIONS
One to four racks can be used simultaneously
during convection baking. Place the rack(s) in the
desired position before turning the oven on. Store the
unused racks out of the oven.
Rack position 2 (second from bottom) will probably
be used the most for single rack convection baking.
When baking on more than one rack you do not
LGR SERIES
need to stagger the pans. Allow at least 1" of space
between the oven walls and the pans so the heated
air can circulate. Pans should be placed in the
center of the oven, stacked above each rack.
REGULAR BAKE
Bake is baking with hot convected air; there is no
fan. The air movement comes from natural convection
as the air heats, it moves to the top of the oven.
This oven mode is the same as you have been using
for baking on one or two racks.
FOODS SUITABLE FOR BAKE
Appetizers
Pies, Cakes
B r e a d s
Desserts
Main Dishes
Oven Meals (1 to 2 racks)
Poultry
Roasts
CAUTION: Aluminum foil should never be used to
cover the oven racks or to line the oven bottom.
The trapped heat can damage the porcelain and
the heated air cannot adequately reach the food
being baked.
RACK POSITIONS
One or two racks can be used simultaneously during
bake. Place the rack(s) in the desired position before
turning the oven on. Store any unused racks out of
the oven.
Rack position 2 (second from bottom) will probably
be used the most for single rack baking.
If you are using two racks simultaneously, be sure to
check the food on the bottom rack sooner than the
minimum time. The food on the lower rack position
may cook slightly faster than the food on the upper
rack, particularly if you are using large baking utensils so
that one is not directly above the other and the heated
18
LGR SERIES
USING YOUR OVEN
at least one inch of space between the oven walls and
the pans.
If using large or commercial size baking utensils, the
food may take a few extra minutes as the air cannot
circulate as freely as it does with a smaller pan. When
using commercial size baking utensils, use only one
GETTING THE BEST RESULTS
BAKING:
 Follow the recipe amount and ingredients,
including the size and shape of the baking utensil
recommended in the recipe.
 Do not open the oven door "just to peek," use the
interior oven light and look through the window.
 Do not use the oven for storage, especially when
baking in the oven. Extra utensils, not being used
for baking, can affect the food product, baking
time, browning, and end result.
 If you are using glass utensils, lower the temperature 25°F.
 Use a minute timer and set it for the minimum
time suggested in the recipe.


Do not refreeze.
Be sure to read the basic information on convection
before using the oven for the first time, page 14-16.
Keep in mind that convection baking results vary,
depending on type of product.
FOOD SAFETY
Notes:
HIGH ALTITUDE BAKING
Recipes and baking times vary if you are baking at high
altitude. For accurate information, write to the. Agriculture
Extension Service. Colorado State University, Fort
Collins, Colorado 80521. Specify the type of information
and the baking mode (convention bake or bake) you need,
i.e. cakes, breads, etc. There may be a cost for the bulletins.
TO USE THE OVEN ON LOW TEMPERATURE
The oven can be used to keep hot food hot, to dehydrate
food, to warm plates, for slow cooking (as in a crock pot),
and to defrost foods.
You can keep hot, cooked food at serving temperature. Set
the oven to the temperature suggested in the chart. Rare
meat must be eaten when it is removed from the oven, as
continues cooking from its own heat.
CONVECTION BAKING
To keep food moist, it must be covered with aluminum foil or a lid.
 Follow the first three recommendations above.
To dehydrate food, follow suggestions in a recipe.
 Metal utensils give better results, in convection, than
do glass baking utensils. If you use glass, it usually is
not necessary to lower the temperature an additional
25°F.
 Use a minute timer and set it for less than minimum
time suggested in the recipe. The first time you use a
recipe in the convection mode, be sure to note the
new baking time on your recipe for future reference.
To thaw frozen cooked food, set the oven knob to
170°F. Loosen the freezer wrapping. Do not use plastic wrap or wax paper in the oven.
To warm plates, check with the dishware manufacturer for
the recommended temperatures.
To use the oven as a low cooker set the oven control knob
to 255°F. Place the food in the oven in a pan with a tight fitting
lid. Follow recipes for this type of cooking.
To thaw uncooked frozen food, set the oven control knob
to "warm". Be sure the food is tightly wrapped in foil. Thaw
the food just enough. Cook immediately.
According to the United States Department of Agriculture you should not hold foods at temperatures
between 40°F to 140°F for longer than 2 hours.
USING CONVECTION
BROIL.
BROIL
AND
REGULAR
TO SET THE OVEN FOR CONVECTION
BROIL AND REGULAR BROIL
CAUTION: Pay special attention when setting the
Oven Control Knob on "BROIL". If you set the knob
past the "BROIL" setting, the burner will not ignite.
Decide if you are going to use REGULAR BROIL or
CONVECTION BROIL. If you are going to use regular
broil turn the Oven Control knob To "BROIL". To use
Convection Broil turn the Oven Control Knob to
"BROIL" and press the CONVECTION button to operate
the fan. The burner will ignite after the gas reaches
the burner. The "oven on" indicator light will come
on to let you know that the broiler is currently on.
During the broiling process, the infra-red burner
produces such an intense heat that the burner will
cycle on and off to maintain an efficient yet safe
interior cooking environment.
The HEATING indicator light on the valve panel cycles
on and off with burner to let the user know when the
burner is lit. This cycling process is used to evenly
distribute and safety control the intense heat that the
broil burner produces. The cycling feature prevents
the burner from producing range-damaging heat.
RACK POSITION
The rack position depends on the type and
thickness of the food. Thick pieces of meat or
poultry (1" or more) would typically be broiled
or convection broiled on rack position 4. Steaks,
19
LGR SERIES
USING YOUR OVEN
chops and hamburgers would typically be broiled
on rack position 4. If top browning casseroles or
bread, the thickness of the food will indicate the position. Casseroles and bread would typically be
browned on rack position 2 (see instructions below
for more information).
CONVECTION BROIL
Convection broil is cooking by intense infrared radiant
heat supplied by the broil burner while fan at the back
of the oven circulates hot air in a continuous pattern
around the food. Convection broil cooks the food with
better results for thicker cuts of meat. The meat sears
on the outside and retains more juices and natural
flavor inside with less shrinkage.
FOODS SUITABLE FOR CONVECTION BROILING:
Thicker Cuts of Meat (1" or more)
Rack position #3 (same position for broiling)
Thicker, Irregular-sized Pieces of Poultry (1" or more),
Rack position #2 or #3 (same position for broiling)
Thicker, Pieces of Fish (1" or more)
Rack position #3 (same position for broiling)
Top Browning: Casseroles and Breads
Rack position #2 or #3 (same position for broiling)
REGULAR BROIL
Broil is cooking by intense infrared radiant heat supplied by
the broil burner located at the top of the oven.
FOODS SUITABLE FOR BROILING:
Appetizers
Rack position #3 or #4
Meats, Poultry, Fish (under 1")
Rack position #4
Top Browning: Casseroles and breads
Rack position #2 or #3
NOTE: The broiler pan for both broiling and convection
broiling should be placed all the way to the back of the
oven and centered on the rack for best results.
USING A MEAT THERMOMETER TO BROIL AND
CONVECTION BROIL
To accurately determine the doneness of a thick steak or
chop (1-1/2) inches thick or more), use a meat thermometer. Insert the point of the thermometer into the
side of the meat to the center. Cook the first to 90°F for
rare meat. Cook the first side 100°F for medium to
well done. Cook the second side to the desired degree for the doneness you want, 140°F to 145°F for
rare, and 150°F to 155°F for medium and 160°F to
165°F for well done. If you are cooking pork, cook to
160°F.
A large two-piece broil pan comes with your new
range. When you are broiling, always use both
pieces. Do not cover the grid with aluminum foil.
This slotted grid allows the grease drippings to flow
into the bottom of the pan keeping it away from the
intense heat of the infra-red broiler burner. This help to
minimize the smoking and spattering of the grease.
TO GET THE BEST RESULTS
OPEN DOOR BROILING
NOTE: Open Door Broiling is also possible with the
Precision Series oven. However, the oven door hinge
DOES NOT have a dedicated Broil-Stop position. To
achieve the best results for Open-Door Broiling, open
oven door approximately 6-8 Inches.
WARNING! NEVER leave pets and/or small children
unattended while oven is in the Open Door Broiling
position. Front panel and knobs may get hot to
the touch as the heat is directly escaping to the
front section of the oven. Wear oven mitts and
always use Caution!
 Defrost the food before starting to cook.
 Put food on broiler pan, center and push broiler pan
to the very back of the oven rack.
 Set a minute timer for the minimum time to check the
food.
 Steaks should be at least one inch thick, if rare doneness
is desired. It is difficult to get rare with meat that is thinner.
 After half the total cooking time, turn the food over only
once. It is not necessary to turn over thin foods (fillet
of fish, Ham slices, etc.). Liver slices must be turned
over.
 Use a two-piece broil pan. Two-piece broil pans are
designed to minimize smoke and spatter. DO NOT
cover the slotted grid with aluminum foil. This will
catch the grease and could cause a fire.
When top browning use metal or glass-ceramic bake
ware. DO NOT use heat-proof Glass or pottery as this
type of glassware cannot withstand the intense heat
of the broiler burner.Place the vertical positioning
rod into the hole located on the bottom left side of
the oven can.
 NOTE: You cannot use the broiler burner and
the bake burner at the same time. When one is
on, the other cannot be turned on!
NOTE: It is not recommended to use the convection
fan if Open Door Broiling.
20
LGR SERIES
USING YOUR OVEN-SELF CLEAN MODE
INTERNAL COOKING TEMPERATURES:
FOOD
OVEN TEMPERATURE
Egg and Egg Dishes
Eggs
Cook until yolk and
white are firm
Egg Casseroles
160 degree F
Egg Sauces, Custards
160 degree F
Ground Meat and Meat Mixtures
Turkey, Chicken
165 degree F
Beef, Veal, Lamb, Pork
160 degree F
Fresh Beef, Veal, Lamb
Medium Rare
145 degree F
Medium
160 degree F
Well Done
170 Degree F
Fresh Pork
Medium
160 degree F
Well Done
170 degree F
Roast Beef
Cooked Commercially
140 degree F
Vacuum Sealed
140 degree F
Ready to eat
140 degree F
Poultry
Chicken, Turkey-Whole
180 degree F
Chicken, Turkey-dark meat 180 degree
F
Poultry-breast
170 degree F
Duck and Goose
180 degree F
Stuffing
Cooked alone or in bird
165 degree F
Sauces, Soups, Gravies, Marinades
Used with raw meat, poultry, or fish Bring to boil
Seafood
Fin Fish
Cook until opaque and
flakes easily with a fork
OVEN SELF-CLEANING
The self-cleaning oven of your new range features
pyrolytic self-cleaning. When set in the SELF-CLEAN
mode, the oven reaches a high temperature that
burns off the food soil.
When the oven is on for SELF-CLEAN, only the
RANGETOP burners can be used.
NOTE: Before turning oven to self-clean mode,
wipe up the excessive Food Soil. This will minimize
any excessive smoke or flames that may occur.
OVEN DOOR LOCK DURING SELF-CLEAN
When the clean cycle starts, the lock light turns on,
and the automatic door lock cycle begins. Do not
attempt to open the door when the lock light is on.
You can stop the cycle by turning to OFF position.
The lock light will turn off only after the oven has
cooled below 550°F, and the automatic door lock has
completed its cycle to the open position.
BEFORE SELF-CLEANING THE OVEN: Remove all
utensils and racks.
 Clean the oven front frame and outer door edges.
Wipe up large spill ovens and grease.
It is common to see smoke and/or flames
during the SELF-CLEAN cycle, depending on
the content and amount of soil remaining in the oven.
If a flame persists, turn off the oven and allow it to
cool before opening the door to wipe up the excessive food soil.
 Be sure the light bulbs and glass covers are in place.
 Turn on the ventilation hood above the range and
leave it on until after the oven has completed the self
-clean cycle.
 Wipe out puddles of grease and any loose soil that
can be easily removed.
 Remove any soil that is outside the door seal area.
This appliance is designed to clean the oven interior
and that portion of the door that is inside the oven.
The outer edges of the door are not in the cleaning
zone.
WIPE THIS AREA CLEAN BEFORE SETTING
THE OVEN TO SELF-CLEAN.
At the end of the SELF-CLEAN cycle, some gray ash or
burned residue may remain inside the oven. This is a
mineral deposit that does not burn or melt. The amount
of ash depends on how heavily soiled the oven was
before the oven was cleaned. It is easily removed,
once the oven has cooled, using a damp paper towel,
sponge, or cloth.
SETTING THE OVEN FOR SELF-CLEAN
Wipe off any smoke residue that remains on the
front frame with Formula 409® or Fantastik®. If
stain remains, use a mild liquid cleanser. The amount
of smoke stain is directly related to the amount of food
soil left in the time of self-cleaning. Clean the oven
often.
1. Set Oven Control Knob to "CLEAN".
 Blower turns on.
 SELF-CLEAN Light turns on.
 DOOR LOCK Light turns on immediately and the

door latch engages within 10 seconds of setting
Oven Knob to Self-Clean Mode.
The door closing process takes approximately 60
seconds to complete, at which time the door becomes locked.
21
SELF-CLEAN MODE/CARE AND MAINTENANCE
AT THE END OF THE CLEAN CYCLE
The Clean cycle takes 5 hours to complete.
The DOOR-LOCK light turns off once the cycle
has finished.
1. The door latch will open automatically after
the oven temperature falls below 550°F and the
automatic Door Lock completes its 60 sec,
cycle to the OPEN position.
CAUTON: The interior of the oven will still be at
baking temperature when the lock light turns off
and the oven door can be opened. Use caution as
the oven may be hot enough to cause burns.
2. Turn the Oven Control Knob to OFF. Wipe off white ash
residue with a damp cloth or sponge before placing
oven racks.
3. Replace the oven racks.
All stainless steel parts of the appliance can be
cleaned with hot soapy water, rinsed, dried and
buffed to a shine with a soft, heavy pile cloth. Make
sure you clean in the DIRECTION OF THE GRAIN
and never in circular motions as this may scratch
NOTE: BRAND NAMES - In this section on
cleaning,the use of name brands is intended
only to indicate atype of cleaner. This is not
constitute an endorsement.The omission of
any name brand cleaner does notimply its
adequacy or inadequacy. Many products are
4. Be sure to rinse all parts thoroughly and to
wipedry to avoid water marks.
burners clean. It is necessary to clean the burnersif they do not light even through the igniter clicks,
ifthere has been a severe boil over, or when the flame
RANGETOP
Turn of all the burners and allow the grates to cool before starting
to clean the range top. Do not clean hot surfaces.
This could burn you. Clean only when the range or Range
top has cooled to room temperature.
BURNER GRATES
When lifting the grates, be careful as they are heavy.
Place them on a protected surface, so they won't
scratch the surface they are laid on.
The burner grates are matte porcelain enamel
over cast iron. When cool they may be placed in
the dishwasher, or wipe while on the range top
using hot soapy water, then rinsed and wiped dry.
The burner grates will not rust as they are matte
porcelain enamel on both sides for durability.
When cleaning this range or range-top:
1. Always use the mildest cleaning procedure
first. Some brands of cleaners of the same type
are harsher than others, read their directions. A
scent or a propellant can make a difference in
the product. Read the ingredients. Try on a small
area first.
2. To avoid marring the surface always rub metal
finishes in the direction of the polish (grain)
lines. The cleaner will be more effective when
used in the direction of the polish lines.
3. Use only clean sponges, soft cloths, pa per towels,
for cleaning or scouring (Use only soap pads
with soap still in them. An empty pad can
scratch), as recommended in this section.
LGR SERIES
The occasional use of mild abrasive cleaners such
as Bon-Ami®, Soft Scrub®. Abrasive cleansers,
used vigorously or too often, can eventually harm
the enamel. Apply with a damp sponge, rinse
thoroughly and dry.
The porcelain may pop of the edge of the grates
due to rapid temperature change when the burners
are turned on, Do not be concerned as this does not
result in the deterioration of the grates. The cast iron
soon darkens to blend with the porcelain enamel. Be
careful when wiping an area where the porcelain has
popped off, as the edges may be sharp.
BURNERS
For proper lighting and performance keep the
the grates and burners are cool, remove the grate.
The Burner Cap and the Retention Ring can easily
beRemove. Wash these parts in hot soapy water,
rinseand dry thoroughly. The Burner Caps are porcelainenamel, follow the directions on the previous
pagethat were given for the burner grates. A bristle
brushcan be used to clean out the toothed burner
ports,if necessary.
After cleaning, it is important to make sure the
Locating Pin at the bottom of the Burner Cap is
properly aligned with the Retention Ring and
Burner Base.
Incorrect alignment will produce a potentially
dangerous flame and poor burner performance
22
CARE AND MAINTENANCE
IGNITERS
Wipe with a water-dampened cotton swab. Be
careful not to damage the igniter. (See illustration).
CONTROL KNOBS - RANGETOP AND OVEN
These are made of die-cast metal with plastic inserts for
easier gripping. They can be cleaned in hot, soapy water.
To remove the Knobs from the control panel, grasp the knob
and pull straight forward. Wash, do not soak. Rinse and
dry thoroughly. It is important to replace these knobs on the
correct gas valve on the control panel.
LOW BACK, OR HIGH SHELF (IF INSTALLED)
Depending on the model, these are constructed of all
stainless steel. Use the mildest cleaning procedure
first— hot soapy water, rinse and dry. If the panel has
food soil remaining, try a general kitchen cleaner,
such as Fantastic, Simple Green®, or Formula 409.
For hard to clean soil use a stainless steel cleaner
such as, Bon-Ami®,, Carneo®,, or Bar Keepers
Friend. Apply cleaner with a damp sponge, rinse thoroughly and dry. Always scrub lightly in the direction of
the grain. Do not use a steel wool pad, it will scratch
the surface. To touch up noticeable scratches in the
stainless steel, sand very lightly with dry 100 grit emery paper, rubbing in the direction of the grain.
After cleaning use a stainless steel polish, such as
Stainless Steel Magic.
If the rear top burners are used extensively on high it is
possible for the vertical stainless steel panel to discolor
from the burner heat. This discoloration can be removed by
using Revere Ware Stainless Steel Cleaner.
OVEN AND DOOR INTERIOR
If in the event the oven door comes off track, or becomes misaligned, realignment can be achieved by
following this simple procedure:
Open the door and hold it all the way open. Close the
hinge latches. Once both hinges are locked, gently
lift the door up and partially out until the door is
evenly aligned. Evenly slide the door back into place
and check to assure the hinges rest in
LGR SERIES
the center of each door hinge roller. With the oven
door fully open, unlock hinge latches and the door is
ready to close again. Call our service technician if
you encounter difficulty.
DOOR GASKET
Use a general kitchen spray cleaner, such as Formula
409 or Fantastik®. Spray it and blot drywith a cloth. Do
not rub. Do not remove or damage the gasket
Be sure the oven and door are cool before you start to
clean them. They are porcelain enamel coated. It is
acid resistant, but not acid proof. Therefore, acid
foods, such as vinegar, rhubarb, alcohol, citric juices or
milk, should be wiped off and not allowed to brake on.
OVEN LIGHT BULB REPLACEMENT
For oven light bulb replacement use only a 40 watt,
120 volt appliance light bulb. These are available in
supermarkets. DO NOT use a standard light bulb in
any oven, the heat will break it.
Try mild cleaners, such as: Bon-Ami®, Ammonia,
Ammonia and water, or Soft Scrub®. Apply the
cleaner on a damp sponge or cloth. Rub lightly. Rinse
thoroughly and dry. If food has burned onto the oven
and is difficult to remove, soak the spots with a cloth
saturated with household ammonia. Allow it to soak
for an hour or two, with the door closed. The food soil
should be easy to remove with a damp soapy cloth or
mild abrasive.
TO REPLACE THE LIGHT BULB:
1. Be sure the oven light bulb switch is in the off
position.
2. Let the cover and the bulb cool completely.
3. Remove the light cover, Turn the cover to the left
(counterclockwise) to unscrew it.
4. Remove the burnt out bulb. Replace itwith a 40
watt appliance light bulb only.
5. Replace cover. Turn circuit breaker back on, if
turned off. (See Caution below).
OVEN RACKS AND ROLLERS
The oven racks and rollers are chrome plated steel.
Chrome cleaners, such as Soft Scrub, Cameo or Bar
Keepers Friend can be applied with a damp sponge
following package directions. Rinse and dry. Powdered
cleaners such as Bon-Ami® or Comet are applied with a
damp sponge or cloth, rubbed lightly, rinsed and
dried. Harsh Cleaners which are commercial oven
cleaners, such as Easy Off® or Dow can be used on
the racks. However, some commercial oven cleaner's
cause darkening and discoloration. Test the cleaner on a
small part of the rack and check for any discoloration
before cleaning the entire rack. Allow to stand for 15 to 20
minutes. Rinse thoroughly and dry.
FRAMES, SIDES, DOOR EXTERIOR, HEAT DEFLECTOR
These parts are made of stainless steel, follow the
directions for the Backguard (see page 28). Take
care when cleaning the door top. Do not let water or
cleaners run down the vents. If water or cleaners spill
into the vents, they may streak the glass inside the door.
CAUTION: Be sure the oven light switch (see
page 8, # 11) is in the OFF position and the
light cover is cool. If the bulb comes loose
from its base, turn off the power to the oven at
the circuit breaker panel, before attempting to
remove the bulb base from the socket.
POWER FAILURE
The broiler and oven burners cannot be turned on
during a power failure. To light the sealed top burners, turn the control knob to "lite" hold a lighted match
to the port ring. After the flame is burning all the
way around the burner, adjust the flame to the
desired height. It is necessary to light each
burner individually. Do not light more than one
burner at a time.
23
CARE AND MAINTENANCE / LOCATING RATING PLATE
LGR SERIES
LOCATING RATING PLATE
SERIAL #, MODEL # AND VERIFYING GAS TYPE
The rating plate contains necessary information
regarding your range. It provides the model #, serial #
and verifies the gas type and BTU input ratings for
each burner of your appliance. When calling for
service, please have this information at hand.
The model #, serial # and gas type information is
located in two places. First, when you open the oven
door, you will find a sticker that shows the model #
followed by either an N (for natural gas) or L (for LP
gas), and the serial # (see picture).
The rating plate, showing the model #, serial #, gas
type and gas BTU input ratings for each burner, as
well as necessary information from ETL test labs,
is located behind the kick-plate. You will need to
remove the kick-plate to access this information
(see picture).
24
LGR SERIES
TROUBLESHOOTING
RANGES AND RANGE-*TOP
PROBLEM
POSSIBLE CAUSE
PROPOSED SOLUTION
Range non-functional
No electricity or gas supply
Turn on gas supply valve
Check circuit breakers
One or more burners will not light
Incorrect flame/ sooty burner flame
BBQ-GRILL doesn't light
Technical
Call for authorized service
No electricity
Check circuit breakers
No gas
Check gas supply at wall
Wrong gas type
Verify gas type
Burners are dirty
Clean burners ports
Burners are mis-aligned
Align and reassemble burners
Water in burner(s)
Dis-assemble and dry burners
Dirty electrode(s)
Clean burner electrode
Technical
Call for authorized service
Too large or small flame
Verify gas type
Mis-aligned burner assembly
Realign and re-assemble burner assembly
No Electricity
Check circuit breaker
No gas
Check gas supply at wall
Burner is dirty
Clean burner
25
LGR SERIES
TROUBLESHOOTING
RANGE OVENS
PROBLEM
POSSIBLE CAUSE
PROPOSED SOLUTION
No oven light
No electricity
Check circuit breakers
Check plug at wall
Ensure bulb is properly screwed in
Replace bulb
Loose bulb
Burned out bulb
No oven heat (bake)
No oven broil
Uneven baking
No gas
No electricity (check oven light)
Improper settings
Check for proper top burner operation
Check circuit breakers
Check plug
Verify proper settings on knob selector
Improper settings (see no bake)
Verify proper settings
Insufficient pre-heat time
Improper settings
Allow oven to preheat at least 15 minutes before
baking
Verify proper settings on knob selector
Improper utensils/placement
Use proper utensils and place them properly in
the proper rack positions
No convection
No convection fan
Check for air movement
Convection noisy
Technical
Call for authorized service
26
INSTALLATION INSTRUCTIONS
LGR SERIES
LG SERIES RANGES
LGR SELF CLEAN CONVECTION MODELS
LGSCR ( 30” 36” 48” )
27
TABLE OF CONTENTS
Important Information
29
All Models
30
30" -
36" - All Models
48" - All Models
31
32
xx" - All Models
33
Unpacking and Ventilation Requirements
34
Cabinet Install Drawing / Front View
Cabinet Install Drawing / Side View
LGR SERIES
35
Installation Instructions
36
37-38
Gas Hook-Up / Testing and Adjustments
39
Post-Install Check
40
Service & Warranty Info
41
28
IMPORTANT INFORMATION
PLEASE READ ENTIRE
INSTRUCTIONS
BEFORE PROCEEDING.
WARNING! If the information in this manual is
not followed exactly, a fire or explosion
may result causing property damage, personal
injury or death.
WHAT TO DO IF YOU SMELL GAS
 Do not try to light any appliance
 Do not touch any electrical switch
 Do not use any phone in your building
 Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier's instructions.
If you can not reach your gas supplier, call
the fire department.
IMPORTANT: Save these instructions for the Local
Gas Inspector's use.
INSTALLER: Please leave these Installation
Instructions with the unit for the owner.
OWNER: Please retain these instructions for future
reference.
The appliance, when installed, must be electrically
grounded in accordance with local codes or, in the
absence of local codes, with the National Electrical
Code, ANSI/NFPA 70
The appliance and its individual shutoff valve must
be disconnected from the gas supply piping system
during any pressure testing of that system at test
pressures in excess of 5 psi (35 kPa).
The appliance must be isolated from the gas supply
piping system by closing its individual manual
shutoff valve during any pressure testing of the gas
supply piping system at test pressures equal to or
less than 5 psi (35 kpa).
WARNING! Disconnect Power before installing.
Before turning power ON, be sure that all controls
are in the OFF position.
IMPORTANT! Installation must conform with local codes.
IMPORTANT INSTALLATION INSTRUCTIONS
INTRODUCTION
Capital's LGR Series Gas Ranges are tested and
approved in accordance with ANSI Z21.1.2005, CAN
1-1.1,M81 1995, Household Cooking Appliances. It is
STRONGLY RECOMMENDED that this appliance be
installed in conjunction with a suitable overhead CAPITAL
VENT HOOD Due to the high heat output of this unit, particular
attention should be paid to the hood and ductwork
installation to assure it meets local building codes.
NOTE: Local building codes vary. Cabinet storage
above the unit should be avoided to prevent the
risk of accidental fire or burns.
In the commonwealth of Massachusetts, gas
c onnect ion mus t be per f or med by a lic ens ed
plumber or gas fitter.
IMPORTANT! Installation, electrical connections,
grounding and gas connections must comply with
all applicable codes. In the absence of local codes,
the unit should be installed in accordance with the
National Fuel Gas Code ANSI Z223.1/NFPA54CURRENT ISSUE and National Electrical Code ANSI/
NFPA70-CURRENT ISSUE.
Be sure the unit being installed is set up for the
type of gas supplied. The Gas range shipped from
the factory is set for Natural Gas or LP (Propane),
depending on the specific model ordered.
ENSURE THAT THE RANGE IS COMPATIBLE WITH
GAS SUPPLY AT THE INSTALLATION SITE BEFORE
PROCEEDING FURTHER. Contact the dealer if it
is not set for the proper gas supply available at the
installation site.
LGR SERIES
IMPORTANT! A back guard must be utilized when
there is less than 12" horizontal clearance between
combustible materials and the back edge of the
range. The Capital CULINARIAN SERIES Low Back or
High Shelf must be ordered separately and installed at
the rear of the range. For island installations and
other installations with more than 12" clearance, our
stainless steel Island Trim is suitable to cover the
back guard mounting flanges.
GAS SUPPLY
NATURAL GAS: 6-inch water column. (14.9mb)
Min., 8 inch (20mb) nominal
PROPANE GAS: 11-inch water column. (27.4m b),
14 inch (37mb) maximum
ELECTRIC POWER SUPPLY
LGMCR30, LGSCR30 models — 120 VAC, 60 HZ, 1
PH., 20 Amp Circuit
LGMCR36, LGSCR36 models — 120 VAC, 60 HZ, 1
PH., 20 Amp Circuit
LGMCR48, LGSCR36 48 models — 120 VAC, 60 HZ,
1 PH., 20 Amp Circuit
COBSCR60 Models 120 VAC, 60 HZ, 1 PH, 20 Amp
STEP 1: UNPACKING, MOVING and PLACING the
RANGE
C AUT ION : Pr o p er eq u ip ment an d ad eq uat e
manpower must be used in moving the range to
avoid damage to the unit or the floor. The unit is
heavy and rests on stainless steel legs.
 It is strongly recommended that after removing the
packing material, remove the door(s), top grates,
oven racks, front kick plate and drip pan(s) to
facilitate lifting and easier handling.
 Remove the outer carton and packing materials
from the shipping base. The all gas ranges are held to
the skid by three (3) bolts. After removing the bolts
the range must be lifted and removed from the skid.
Never lift the range from the oven door handle.
29
30” ALL MODELS
LGR SERIES
LGSCR304 FOUR Burners At 17.000 btu
30
36” ALL MODELS
LGR SERIES
LGSCR364B Four Burners At 17.000 btu + 12” BBQ Grill
LGSCR366 Six Burners At 17.000 btu
LGSCR364G Four Burners At 17.000 btu + 12” Thermo-Griddle
31
LGR SERIES
48” ALL MODELS
LGSCR488 Eight Burners At 17.000 btu
LGSCR484BG Four Burners At 17,000 btu
+ 12”BBQ Grill + 12” thermo-Griddle
LGSCR486B Six Burners At 17.000 btu
+ 12”BBQ Grill
LGSCR486G Six Burners At 17.000 btu
+ 12” thermo-Griddle
32
60 ALL MODELS NOT AVAILABLE
LGR SERIES
33
LGR SERIES
UNPACKING AND VENTILATION REQUIREMENTS
 Lift the range from the skid with a soft wheel dolly.
 Support the range uniformly across the bottom
surface. Where space permits, a hood larger in
width than the cooking surface may be desirable for
improved ventilation performance.
 To remove door, open the door completely, close
the hinge latches and release the door. Remove
door by lifting and pulling from the sides.
VENTILATION UNIT
STANDARD COUNTER
INSTALLATION
RECOMMENDATIONS
HOOD
(24" DEEP X UNIT WIDTH)
 Make sure gas and electric connections are made,
anti-tip device is installed, and the back guard
installed prior to placing the range in position.
 Measure the height of the counter top and adjust
the range height to match countertop height by
adjusting front and rear leveling feet.
 Slide the range in place and ensure that the range
is level.
 Reinstall the kick plate, top grates, oven door(s),
drip pan tray(s), and make sure burner caps are
seated firmly located into position.
WARNING: DO NOT lift the range by the oven
door handles, Do not remove the griddle and
grill sections!
STEP 2: VENTILATION REQUIREMENTS
It is strongly recommended that a suitable CAPITAL
exhaust hood be installed above the range. Downdraft
ventilation should NOT be used. The table below
indicates the PERFORMANCE Series Hoods, by
model number, that are recommended for use with all
ranges.
1. SELECT HOOD AND BLOWER MODELS:
SIZE
30"
36"
48"
60"
SHIPPING WEIGHT
350
450-550
595-695
700-850
For wall installations, the hood width must, at a
minimum, equal the width of the range's cooking
BLOWER CFM's
60" RANGE = 1200 CFM
48" RANGE =1200 CFM
36" RANGE =1200 CFM
30" RANGE = 600 CFM
CAUTION: Ventilation hoods and blowers are
designed for use with single wall ducting.
However, some local building codes or inspectors
may require double wall ducting. Consult local
building codes and/or local agencies, before
starting, to assure that hood and duct installation
will meet local requirements.
CAPITAL Hood blower speeds are variable to reduce
noise and loss of heated or air-conditioned
household air when maximum ventilation is not
required. Normally the maximum blower speed is
only required when using the grill section.
2. HOOD PLACEMENT:
For best smoke elimination, the lower edge of the
hood should be installed a minimum of 30" to a
maximum of 36" above the range cooking surface.
STEP 3: CABINET PREPARATION
1. The range is a freestanding unit. If the unit is
to be placed adjacent to cabinets, the clearances
shown in fig. 1 are required. The same clearances
appl y to i s l and i ns t al l at i ons , except f or t he
overhead cabinets, which must have a space wide
enough to accept a suitable flared island hood, as
indicated in fig. 1. Note: Capital does NOT
offer an island style ventilation hood at this
times.
2. T h e d e p t h o f o v e r h e a d c a b i n e t s installed on
either side of the hood is 13".
3. A 30-inch minimum clearance is required between
the top of the range and the bottom of an
unprotected cabinet.
4. Any openings in the wall behind the range and in the
floor under the range must be sealed.
5. W h e n t h e r e i s l e s s t h a n 1 2 " h o r i z o n t a l
clearance between combustible material D and
the back edge of the range above the cooking
surface, a Capital Low Back or High Shelf
back guard must be installed (see Fig. 2A).
When clearance to combustible material D is
over 12", a Capital Island Trim may be used
(See Fig. 2B). Figures 2A and 2B indicate the
space required for each type of back guard.
6. Always keep appliance area clear and free from
combustible materials, gasoline, and other
flammable vapors and liquids.
7. Models with open broiler, noncombustible
material is to be installed on the underside of
a cabinet located above the broiler section or
unit in accordance with local codes, or in the
absence of local codes, with the National
Fuel Gas code, ANSI Z223.1/NFPA.54
WARNING: DO NOT obstruct the flow of
combustion and ventilation air to the unit.
PLEASE NOTE:
In the Commonwealth of Massachusetts, gas
connection must be performed by a licensed
plumber or licensed gas fitter.
34
CABINET INSTALL DRAWING / FRONT VIEW
LGR SERIES
FIG 1A. Cabinet Clearances:
35
CABINET INSTALL DRAWING / SIDE VIEW
LGR SERIES
36
LGR SERIES
INSTALLATION INSTTRUCTIONS
WALL MOUNT BACKGUARD INSTALLATION
NOTE: ALL LG SERIES RANGES come
with an island trim.
Secure the back guard (18" High Shelf, or 9" Low
Back) directly on the wall behind range and
above the factory installed island trim. DO NOT
REMOVE the island trim. It is necessary for proper
venting of the oven gases/heat.
BACKGUARD MOUNTING:
WALL MOUNT HIGH SHELF
First measure from top of island trim to 16 3/8"
to what will be the center of the mounting
brackets. (see Fig 1)
ELECTRICAL SUPPLY, ALL RANGES
In sta l l a ti o n o f Al l L G r a n g e s m u st b e
planned so that the rough-in of the junction box
for the receptacle or conduit connection allows for maximum clearance to the rear of the unit.
This is especially critical if the junction box in the
wall is directly behind the junction box of the
unit when the unit is installed. To minimize binding
when the unit is connected to the receptacle or
junction box, orient the receptacle or conduit
connector, and slide back into position.
2. Secure both brackets to the wall
using the screws included
3. Attach the shelf to the shelf support panels with
supplied screws.
4. Slide shelf into position and over brackets.
BACKGUARD MOUNTING:
WALL MOUNT LOW BACK
1. First measure from top of island trim to 16
3/8" to what will be the center of the
mounting brackets. (see Fig 1)
POWER REQUIREMENTS: 120VAC, 60 HZ single phase




30" Range – 7 Amps. Max.
36" Range – 7 Amps. Max.
48" Range – 13 Amps. Max.
60" Range – 13 Amps. Max
CAUTION! Disconnect the electrical supply
cord from the wall outlet before servicing
the range. Follow all governing codes and ordinances when grounding. In the absence of
codes follow the National Electrical Codes
ANSI / NFPA No. 70 (current issue).
GROUNDING METHOD
The range is factory fitted with a power supply and
cord with a three-prong grounding plug. It must be
plugged into a matching grounding type receptacle
connected to a correctly polarized 120 Volt
circuit. If the circuit does not have a grounding type
receptacle, it is the responsibility of the installer to
have the existing receptacle changed to a properly
grounded and polarized receptacle in accordance
with all applicable local codes and ordinances. The
receptacle replacement shall be in accordance with
the national Electrical Code.
WARNING! The third prong SHOULD NOT,
under any circumstances, be cut or removed!
37
LGR SERIES
INSTALLATION INSTTRUCTIONS
STEP 4: INSTALLING ANTI-TIP DEVICE
 Failure to follow these instructions may result
in electrical shock or other personal injury.
For all Ranges, an anti-tip device MUST be installed
as per these instructions.
determine the proper method for drilling holes
through the wall or floor material (such as ceramic
tile, hardwood, marble, etc.)
 ALL RANGES CAN TIP
 INJURY TO PERSONS COULD RESULT
 INSTALL ANTI-TIP DEVICES PACKED WITH

RANGE
SEE INSTALLATION INSTRUCTION
WARNING: RANGE TIPPING HAZARD!
 All ranges can tip and injury can result. To
prevent accidental tipping of the range, attach
it to the floor, wall or cabinet by installing the
Anti-Tip Device supplied.
 A risk of tip-over may exist if the appliance is
not installed in accordance with these instructions.
 If the range is pulled away from the wall for
cleaning, service or any other reason, ensure
that the Anti-Tip Device is properly re-engaged
when the range is pushed back against the
wall. In the event of abnormal usage (such as
a person standing, sitting, or leaning on an
open door); failure to take this precaution can
result in tipping of the range. Personal injury
might result from spilled hot liquids or from the
range itself.
longer screws, available at your local hardware store.
 In all cases at least one (1) of the bracket mounting
CAUTION: PROPERTY DAMAGE!
 Contact a qualified installer or contractor to
WARNING!
 The thickness of the wall or floor may require use of
 DO NOT slide range across unprotected floor.
 Failure to follow these instructions may result
in damage to wall or floor coverings.
TOOLS NEEDED FOR INSTALLATION
OF ANTI-TIP DEVICE!
screws must be fastened to solid wood or metal
on each side.
 Use appropriate anchors when fastening the mounting bracket to any material other than hardwood or
metal.
MOUNTING ANTI-TIP BRACKET:
The alternative floor mounted bracket shall
be installed as follows:
 Place bracket on floor in position shown in Figure below.
Screwdriver, Phillips
Drill, electric or hand
Measuring tape or ruler
1/8" drill bit (wood or metal wall or floor)
3/16" anchors, drywall, or concrete, 2 each (not
required if mounting bracket is being attached to
solid wood or metal.
6. Hammer
 Secure to floor or wall stud.
IMPORTANT INSTALLATION INFOR-
Verify the type of gas being used at the installation
site matches the gas type of the range. As shipped
from the factory, units are configured for use with
Natural Gas or Propane (LP). Make certain the range
matches the type of gas available at the location.
1.
2.
3.
4.
5.
 The Anti-Tip Bracket may be attached to a solid
wood cabinet having a minimum wall thickness of 3/4".
 Later, when unit is installed, the adjustable leg will slide
under the bracket
STEP 5: GAS CONNECTION AND HOOK-UP
For installation of the appliance at high altitude,
please consult your local gas company for their
recommendation of the correct orifice sizes and any
other necessary adjustments that will provide proper
gas combustion at specified altitudes.
WARNING: ELECTRICAL SHOCK HAZARD!
 Use extreme caution when drilling holes into

the wall or floor. There may be concealed
electrical wires located behind the wall or under
the floor.
Identify the electrical circuits that could be affected
by the installation of the Anti-Tip Device, then
turn off power to these circuits.
NOTE: Capital DOES NOT supply ranges to match
varying altitudes. Orifices to adjust for combustion for
differing altitudes may be purchased through Capital Cooking Equipment by calling our Parts Department at 1-866-4024600, or email us at customerservice@capital-cooking.com.
38
GAS HOOK-UP / TESTING AND ADJUSTMENTS
CAUTION! When connecting unit to Propane (LP)
gas. Make certain the propane tank is equipped
with its own high-pressure regulator in addition to the
pressure regulator supplied with the appliance the
pressure & the gas supplied to the appliance regulator
must not, exceed 14" ( 37 mb) water column. A
pressure test point is provided near the regulator
behind the kick plate
NATURAL GAS REQUIREMENTS:
 Inlet Connection: 1/2" N.P.T.
 Min. 5/8" Dia. Flex Line.
 Supply Pressure: 6" to 14" W.C.
LGR SERIES
that has been permanently mounted to the range body.
 Use 5/8" diameter flex line to connect between the
gas supply and the appliance manifold pipe, which
exists at the upper left rear of the appliance. The
appliance manifold pipe connection is 1/2". Use
caution to avoid crimping the 5/8" flex line.
 NOTE: the flex line for the gas supply must be
metal and approved by an approved certifying
agency (AGA, CGA, CSA, UL or CUL). NEVER use
a hose made of rubber or other synthetic material
as the heat may cause the hose to melt and develop leaks, thus causing fires, physical and property damage.
PROPANE (LP) GAS REQUIREMENTS:




Inlet Connection: 1/2" N.P.T.
Min. 5/8" Dia, Flex Line.
Supply Pressure: 11" to 14" W.C.
A Regulator is required at the LP source to provide
a maximum of 14" W.C. pressure to the range
regulator.
WARNING! Gas line cannot be run inside back
cover of range. Run gas line in channel in back
of range.
 Always use pipe dope or Teflon tape on the pipe
threads, and be careful not to apply excessive pressure when tightening the fittings.
 Leak testing of the appliance shall be in accordance with the manufacturer's instructions.
 Turn on gas and check supply line connections for
leaks using a soap solution. Never use a flame of
any sort to test for leaks.
HOOK UP
 A manual shut off valve must be installed external to
the range in an accessible location from the front for
shutting off the gas supply when required.
 The supply line MUST NOT protrude beyond the
CAUTION! The appliance must be isolated from the
gas supply piping system by closing its individual
manual shut-off valve during any pressure testing
of the gas supply piping system at test pressures
equal to or less than 112 psig (3.5kPa.).
back of the range.
 Ensure that the gas supply is turned OFF at the
external shut-off valve before connecting the range.
The Appliance and its individual shut off valve
must be disconnected from the gas supply piping
system during any pressure testing of the system
at test pressures in excess of 1/2 psig (3.5kPa.).
 The gas supply connection must be made by an
experienced technician and in accordance with
local codes or ordinances. In the absence of local
codes or ordinances, please refer to National Fuel
Gas Code ANSI Z223.1 / NFPA54-Current Issue.
 The range is supplied with its own pressure regulator
When checking the manifold gas pressure, the inlet
pressure to the regulator should be at least 6.0".
DO NOT attempt any adjustment of the pressure regulator.
TESTING AND ADJUSTMENTS
Install any loose components, such as burner caps and
grates, oven racks that may have been removed earlier to
facilitate moving the appliance. Be certain that burner
caps seats properly into the alignment slots in the burner
bases. Before testing operation of the appliance, verify that
the unit and the gas supply have been carefully
checked for leaks and that the unit has been connected
to the electrical power supply. Turn the manual gas shutoff valve to the open position. Check the operation of
the sealed gas burners by pushing and turning each
knob counterclockwise to "Hl". The burner igniters will
click until the flame ignites. Burner flames should be
BLUE and stable with no yellow tips, excessive
noise, or lifting of the flame from the burner. If any of
these conditions exist, check that the air shutter (grill
and griddle only) or burner ports are not blocked or
clogged. Remove any blockages that exist. If the flame is
too yellow, indicating insufficient air, adjust the shutter
counterclockwise to increase air inlet (grill and griddle only).
The sealed top burner flames should be approximately
1" to 1-1/4" High.
CAUTION! A qualified technician must make
burner adjustments at the time of installation.
Improper or lack of adjustments may cause harmful
by-products or void your warranty!
39
LGR SERIES
POST-INSTALL CHECK
INSTALLER CHECKLIST
ELECTRICAL
FINAL CHECKLIST

Placement of unit
Specified clearances maintained to cabinet surfaces
Unit Level – front to back – side to side
Burner caps and retention rings positioned properly on sealed
burner bases
All packing materials removed
Island trim or back guard attached (if horizontal
clearance to combustible materials behind cooking
surface is less than 12")
Check door adjustment and hold down brackets


















Connection: 1/2" NPT with a minimum of 5/8"
diameter flex line
The appliance is connected only to the type of gas for which it is
certified for use
Manual gas shut-off valve installed in an accessible location (without
requiring removal of range)
Unit tested and free of gas leaks
Gas supply pressure does not exceed 14" (37 mb) W.C.
Proper ground connection
Proper polarity at receptacle
Kick panel in place and 3 screws secure.
OPERATION
GAS SUPPLY

Receptacle with correct over current protection is provided for service cord connection









All internal packing materials removed. Check
below grates and grill pans and inside the ovens
If used on Propane gas, verify that the propane
gas supply is equipped with its own high-pressure
regulator in addition to the pressure regulator supplied with appliance.
Burner caps and retention rings properly seated
into burner bases.
Grill Components properly seated (not all models).
Bezels centered on burner knobs and knobs turn
freely.
Each burner lights satisfactorily, both individually
and with other burners operating
Air shutter adjustment for proper flame made for
Grill and Griddle sections.
Griddle is level and does not rock.
Oven door hinges seated and hinge locks in proper
position. Door opens and closes properly.
Burner grates correctly positioned, level and do not
rock.
Note to Customer.
Please make sure installer signs each item on this
checklist, explains each item before leaving and explains the range operation to you thoroughly.
40
LGR SERIES
SERVICE & WARRANTY
SERVICE INFORMATION
If none of the above has occurred, contact our
customer service department at 1-866-402-4600.
Before you call for service, please have the following
information available:
 Model #
 Serial #
 Date of Installation
 Copy of Receipt or Invoice
 A brief description of the problem
Your satisfaction is our top priority If the problem
persists, or is not resolved to your satisfaction by
our service consultant, please write to us or fax us
Capital Cooking Equipment, Inc.
Attn: Customer Service Manager
13211 E. Florence Ave
Santa Fe Springs, CA
90670
USA
Fax #: 562-903-1167
Email: customerservice@capital-cook!ng.com
WARRANTY
 ONE (1) year full parts and labor covers entire
product.
WILL NOT PAY FOR:
WILL PAY FOR:
All repair labor and parts found to be defective due
to material or workmanship for one (1) full year" IN
HOME" warranty This does not apply if the unit
was subjected to other than normal household use.
An Authorized Factory Agent must provide service
during normal working hours. No charges will be
made for repair or replacement at the location of
original installation. No charges will be made for
defective factory parts returned pre-paid, through
the dealer, and claimed within the warranty period.
All claims, regardless of warranty or non-warranty
must be documented with photos and detailed
description and/or narrative of the problem and
submitted to Capital's service department.
Replacement of parts will be freight prepaid by
Capital and shipped regular ground. Any requests
for other than standard ground shipments must
be paid by customer. The company will not be
liable for additional transportation costs, labor
cost, taxes or export/import duties. This warranty
shall not apply, nor can we assume responsibility
for damage that might result from failure to follow
manufacturer's instructions or local codes where
the appliance has been tempered with or altered
in any way or which, in our judgment, has been
subjected to misuse, negligence, or accident.
Implied warranty shall not extend beyond the duration of this written warranty. This warranty is in
lieu of all warranties, expressed or implied and all
other obligations or liability in connection with the
sale of this product.
 Installation or start-up.








Shipping damage that is not a direct result of packaging
(for example freight handling).
Service by an unauthorized agency
Use of unauthorized parts.
Service during hours other than normal working hours.
Improper installation.
Service visit to teach you how to operate the appliance, correct
the installation, reset circuit breakers or replace fuses.
Repair other than normal household use.
Damage caused by accident, abuse, alteration, misuse,
incorrect installation or installation not in accordance
with local codes.
Unit(s) installed in non-residential applications.
This warranty applies to appliances used In
residential application only. It does not cover their
use in commercial situations. This warranty is for
products purchased and retained in the 50 States of
the U.S.A, the District of Columbia and Canada. This
warranty applies even If you should move during the
warranty period. Should the original purchaser sell
the appliance during the warranty period, the new
owner continues to be protected until the expiration
date of the original purchaser's warranty period. This
verity gives you the specific legal rights. You may also
have other rights, which vary from State to State.
 FIVE (5) years parts on all burners: oven, broiler,

stainless BBQ burner, griddle burners, open
burners, wok burner, top grates, grill grates,
griddle plate
Porcelain enamel is prone to normal wear over
a period of time.
 Lifetime parts against rust on all stainless steel
panels and components.
41
ALL SPECIFICATIONS ARE FOR PLANNING PURPOSES ONLY. REFER TO INSTALLATION INSTRUCTIONS
AND CONSULT YOUR COUNTERTOP SUPPLIER PRIOR TO MAKING COUNTER OPENING. IF YOU HAVE
ANY QUESTIONS, PLEASE CALL US AT 866-402-4600 PRIOR TO CUTTING ANY OPENINGS. CONSULT
WITH A HEATING AND VENTILATING ENGINEER FOR YOUR SPECIFIC VENTILATION REQUIREMENTS.
FOR THE MOST UP TO DATE USE AND CARE AND INSTALLATION INSTRUCTIONS CONTACT
CAPITAL COOKING EQUIPMENT, INC. INDICATING THE MODEL #.
DUE TO ONGOING PRODUCT IMPROVEMENTS, WE RESERVE THE RIGHT
TO CHANGE THESE SPECIFICATIONS, OR DESIGNS WITHOUT NOTICE.
CERTIFIED FOR USA AND CANADA
13211 E Forence Ave. Santa Fe Springs, CA 90670
Toll Free: 866-402-4600
Main: 562-903-1168
Fax: 562-903-1167
Email: customerservice@capital-cooking.com
Website: www.capital-cooking.com
87099-01 Rev-01
Download PDF