Endura ESYNC1 Manual

ENTRYSYNC Lock Overview
Initial lock setup
Phone Application
Operating Your EntrySync Lock
Regulatory Compliance
1
Initial lock set up: Battery Instillation
Locate battery
door.
Remove screw,
battery door and
empty battery pack.
Carefully install fresh AA batteries in the
correct orientation. (Note: for best experience use quality alkaline batteries.)
2
Download Application
Android Products
Plug in the battery pack, insert
battery pack into lock. Route pull tab
from battery pack out the front of
opening to ease future battery replacement.
Apple Products
Download mobile application using these
QR codes, or search for EntrySync in your
app store.
3
Open the Application and create an account. Ensure application has permission to all requested phone functions to allow full lock functionality.
After creating an account follow the series of screens below to set up
your new lock. Note apple and android steps may be different.
If incorrect handing is selected during initial setup you can change this in settings at anytime.
Refer to page 7 or 8.
4
Replace battery door and screw. Ensure the
pull tab for battery pack is installed such that it
does not interfere with the screw installation.
Test lock function using application.
Your EntrySync unit is now ready for
use.
5
Apple Application Screen
This will navigate you to select
from your multiple EntrySync
locks.
Share Ekeys here.
The lock name designated in the set up of this
lock displayed here. This
can be useful in homes
with more than one
EntrySync unit.
Type of Ekey being used.
Lock status at last
communication
displayed here.
You can tap in this
area to toggle between intuitive lock
& unlock icons. In
this case the door
would be locked.
Note: if lock is not
paired with a Gateway this will only
update when inside
Bluetooth range.
Use this to return to
this screen.
Lock Battery Indicator
Selecting this tab allows
you to view the past uses
of the lock.
Note: if lock is not paired
with a Gateway this will
only update when inside
Bluetooth range.
Selecting this tab allows
you to manage other users access to the lock.
Note: You must be an administrative user or the
locks owner to make
changes in this area.
Control various lock
settings here, such as lock
name or door handing.
6
Android Application Screen
This will navigate you to select
from your multiple EntrySync
locks.
Share Ekeys here.
Control various lock
settings here, such as lock
name or door handing.
The lock name designated in the set up of this
lock is displayed here.
This can be useful in
homes with more than
one EntrySync unit.
Selecting this tab allows
you to view the past uses
of the lock.
Selecting this tab allows
you to manage other users access to the lock.
Note: if lock is not paired
with a Gateway this will
only update when inside
Bluetooth range.
Note: You must be an administrative user or the
locks owner to make
changes in this area.
Lock status at last
communication
displayed here.
You can tap in this
area to toggle between intuitive lock
& unlock icons.
Note: if lock is not
paired with a Gateway this will only
update when inside
Bluetooth range.
Lock Battery Indicator
7
Ekeys
Select the key icon found in the top right of the lock home page.
Select from the 3 options for sharing
Ekeys.
Select the type of access you
would like to grant.
Send the Ekey and follow the links
to complete the process. You have
now shared access to this lock.
8
Operating Your EntrySync Lock
Application
Touch to Lock Feature
Device with EntrySync app within Bluetooth range.
Application running on device. (Note: this can be running
in the background)
Tap in this area while in Bluetooth range and the lock
will change state. Please allow the lock time to complete its cycle before requesting another function.
Approach the door with the device from the exterior side
and touch the door about 10 inches above the dead bolt.
You will hear a tone from lock acknowledging your touch.
Troubleshooting:
Ensure the handing is correct on application.
Ensure the lock is synced with the application.
Ensure you have allowed all requested permissions in the
application for full functionality.
Not compatible with steel edge doors.
9
Regulatory Compliance
FCC ID: 2A2PS-ESYNC1
IC: 27615-ESYNC1
HVIN: EntrySync
UNITED STATES of AMERICA
FCC Interference Statement (Part 15.105 (b))
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Howev-er, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Part 15 Clause 15.21 [ Do not Modify warning ]:
“Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment”
FCC Part 15.19(a) [interference compliance statement], unless the following statement is already provided on the device label:“This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.”
CANADA
ISED RSS-Gen Notice
(English)
“This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.”
(French)
“L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
L’appareil ne doit pas produire de brouillage;
L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.”
ISED Canada ICES-003 Compliance Label:
“CAN ICES-3 (B)/NMB-3(B)”
10
Glossary
Ekey:
Gateway:
Touch to lock:
An Ekey is an electronic key stored on your mobile device that grants access
through the mobile application to authorized users. Ekeys can be shared by owners
and admins to give access on both a permanent and temporary basis.
An additional product that pairs with the EntrySync lock to give access
to any authorized user with internet access. The Gateway will connect
your lock to your home internet connection and enables a user to activate the locks functionality outside of Bluetooth range.
This feature allows authorized users to lock and unlock your EntrySync equipped door with a simple touch. When approaching your
door touch the door panel about 10 inches above the dead bolt. The
lock will sound an audible tone to acknowledge the touch, verify
your authorization, then unlock or lock the door.
11
Fort more info and helpful videos please visit EntrySync.com
or our home page at Enduraproducts.com for more great
products.
12