IDZOR HPRT-HT100 User Manual

PR-600 Series HPRT-HT100 User Manual
Label Printer
PR-600 Series
HPRT-HT100
User Manual
PR-600 Series HPRT-HT100 User Manual
Contents
Manual Information ............................................................................................................................. 1
Important Safety Instructions .............................................................................................................. 2
Chapter 1 Introduction ......................................................................................................................... 5
1.1 Packing List ...................................................................................................................................... 5
1.2 Appearance and Components ......................................................................................................... 6
1.3 Dimension ....................................................................................................................................... 7
Chapter 2 Specifications ....................................................................................................................... 8
Chapter 3 Installation & Usage ........................................................................................................... 10
3.1 Media Loading ............................................................................................................................... 10
3.2 Power Connection ......................................................................................................................... 15
3.3 Peripherals Connection ................................................................................................................ 16
3.4 Detection ....................................................................................................................................... 17
3.5 Operation Panel ............................................................................................................................. 23
3.6 Basic Function................................................................................................................................ 24
Chapter 4 Interface ............................................................................................................................ 26
4.1 USB Interface ................................................................................................................................. 26
4.2 Other Optional Interfaces .............................................................................................................. 26
Chapter 5 Maintenance & Adjustment ................................................................................................ 28
5.1 Cleaning Media Sensor .................................................................................................................. 28
5.2 Cleaning Thermal Print Head ......................................................................................................... 28
5.3 Cleaning Roller and/or Paper Path ................................................................................................ 29
Chapter 6 Printer Utility Tool Instructions .......................................................................................... 30
6.1 Installation Preparation ................................................................................................................. 30
6.2 Usage ............................................................................................................................................. 30
Chapter 7 Seagull Windows Driver Instructions ................................................................................. 36
7.1 Introduction ................................................................................................................................... 36
7.2 Installation Preparation ................................................................................................................. 36
7.3 Installation ..................................................................................................................................... 37
7.4 Usage ............................................................................................................................................. 42
7.5 Removing ....................................................................................................................................... 54
Chapter 8 BarTender Ultralite Instructions ......................................................................................... 60
8.1 Introduction ................................................................................................................................... 60
8.2 Installation Preparation ................................................................................................................. 60
8.3 Installation ..................................................................................................................................... 61
8.4 Usage ............................................................................................................................................. 65
Attachment ........................................................................................................................................ 73
Rev.1.0
PR-600 Series HPRT-HT100 User Manual
 Statement
This manual content may be altered without permission, and our company reserves
the rights to make changes without notice in technology, spare parts, hardware and
software of the products. If more information is needed about the products, please
contact our company. Without any written permission from our company, any section
of this manual is prohibited to be copied or transferred in any form.
 Copyright
This manual is printed in 2017, the copyright belongs to IDZOR TECHNOLOGIES CO.,
LTD.
Printed in China
1.0 Version
 Warnings
This must be complied with in order to avoid any damage to the human body
and the equipment.
This is showing the important information and tips for the printer operation.
Note: Due to continuous update of our product, the description of printer
specification, accessories, design in this manual may be slightly different. Please
keep in kind prevail.
Rev.1.0
PR-600 Series HPRT-HT100 User Manual
Manual Information
This user manual contains basic information for product usage as well as for
emergency measures that may be required.
The installation and usage of printer driver, utility tool and HPRT BarTender® Ultralite
are also included in the manual.
1
PR-600 Series HPRT-HT100 User Manual
Important Safety Instructions
Before using the appliance, please carefully read the following safety regulations in
order to prevent any hazard or material damage.
1.Safety warning
Warnings: The print head will become very hot during printing; avoid contact
with the print head after printing has finished.
Warnings: Do not touch the printer head and connector in case static damage
the printer head.
2.Instructions
Warnings: Violating following instructions can cause serious injury or death.
1) Do not plug several products in one multiperture outlet.
• This can provoke over-heating and a fire.
• If the plug is wet or dirty, dry or wipe it before usage.
• If the plug does not fit perfectly with the outlet, do not plug in.
• Be sure to use only standardized multiperture outlet.
2) You must use the supplied adapter.
• It is dangerous to use other adapters.
3) Do not pull the cable to unplug.
• This can damage the cable, which is the origin of a fire or a breakdown of the
printer.
4) Do not plug in or unplug with your wet hands .
• You can be electrocuted.
5) Do not bend the cable by force or leave it under any heavy object.
• A damaged cable can cause a fire.
Rev.1.0
2
PR-600 Series HPRT-HT100 User Manual
Note: Violating following instructions may cause slight damage of the appliance.
1) If you observe a strange smoke, odour or noise from the printer, unplug it before
taking following measures.
• Switch off the printer and unplug the set from the mains.
• After the disappearance of the smoke, call your dealer to repair it.
2) Install the printer on the stable surface.
• If the printer falls down, it can be broken and you can hurt yourself.
3) Use the approved accessories only and do not try to disassemble, repair or remodel
it by yourself.
• Call your dealer when you need these services.
• Do not touch the blade of auto cutter.
4) Do not let water or other foreign objects drop into the printer.
• If this happened, switch off and unplug the printer before calling your dealer.
5) Do not use the printer when it is out of order. This can cause a fire or an
electrocution.
• Switch off and unplug the printer before calling your dealer.
6) Other considerations:
• Place the printer on a solid and even base so that it cannot fall.
• Leave enough space around printer for operation and maintenance.
• Keep all liquids away from the printer.
• Do not expose the printer to high temperatures, direct sunlight or dust.
• Ensure the printer is connected to a socket with the correct mains voltage.
• Switch off the printer POWER supply when it’s not in use for a long time.
• To ensure the printing quality and reliability, suggest use the same quality or
recommend paper supplier.
• Pls. switch off the POWER supply when connect/disconnect all the ports or it will
cause damage to the printer control circuit.
• Never carry out maintenance or repair work yourself. Always contact a qualified
service Technician.
• Keep this User Manual in a place which is easily accessible at all times.
Rev.1.0
3
PR-600 Series HPRT-HT100 User Manual
3.Other Precautions
The copyright for this user manual and various other manuals is property of our
company. Any copying or conversion into electronic form and saving of this material
without the express written permission is strictly prohibited. Use of the information
contained in this manual is not subject to any patent liability. This manual has been
prepared with utmost care and attention to detail but may contain certain errors
and/or omissions. Our company is not legally liable for any damages resulting from the
use of the information in this manual. Our company and its affiliates are not legally
liable (United States excluded) for any damages, loss, costs, and/or expenses that
result from the breakdown, malfunction, and/or misuse of the product due to
violation or neglect of the operation and maintenance information and instructions
provided by our company, as well as from the unauthorized alteration, repair, and/or
modification of the product by the user and/or third party. We are not legally liable for
any damages and/or issues resulting from the use of options and/or parts that are not
authentic or authorized products.
4.WEEE (Waste Electrical and Electric Equipment)
This mark shown on the product or its literature indicates that the
corresponding item should not be discarded at the end of its working life
with other household waste. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, please
separate marked items from other types of waste and recycle them responsibly to
promote the sustained reuse of material resources. Household users should contact
either the retailer where they purchased this product, or their local government office
for details of where and how they can conduct environmentally safe recycling of such
items. Commercial users should contact their suppliers and check the terms and
conditions of purchase contracts. This product should not be combined with other
commercial waste for disposal.
Caution: This is a Class A product. In a domestic environment this product
may cause radio interference in which the user may be required to take adequate
measures.
Rev.1.0
4
PR-600 Series HPRT-HT100 User Manual
Chapter 1 Introduction
1.1 Packing List
Note:
1. Unpack the printer and keep the packing material in case you need to ship the
printer in the future.
2. Any damages exist, please contact the local dealer.
Printer
AC Adapter
Power Cord
USB Cable
Label Roll
Ribbon
CD
Quick Start Guide
Note：The packing materials are actually based on the order.
Rev.1.0
5
PR-600 Series HPRT-HT100 User Manual
1.2 Appearance and Components
￭ Front View
￭ Rear View
￭ Inside View
Note：The views above are for your reference. Ports vary by your choice.
Rev.1.0
6
PR-600 Series HPRT-HT100 User Manual
1.3 Dimension
Rev.1.0
7
PR-600 Series HPRT-HT100 User Manual
Chapter 2 Specifications
(2/1)
Items
Printing
Printing Method
Resolution
Printing Speed
Printing Width
Printing Length
PR-600 HPRT-HT100
Thermal Transfer/Direct Thermal Printing
203dpi(8dots/mm)
127mm/s Max.
108mm Max.
15mm - 1200mm
NUC976
RAM
32MB
Flash
16MB
Adjustable reflective sensor, Fixed transmissive sensor
(Central aligned), Head-up sensor, Ribbon end sensor
Roll-fed or Fan-fed, Die-cut or Continuous label, Tag stock,
Continuous receipt paper
0.79’’(20mm) – 4.65’’(118mm)
0.003’’(76.2um) – 0.007’’(177.8um)
5’’(127mm)
0.5’’(12.7mm),1’’(25.4mm),1.5’’(38mm)
Wax, Wax/Resin, Resin
1.33’’(33.8mm) – 4.33’’(110mm)
328’(100m)
0.5’’(12.7mm)
TSPL, ZPL
Processor
Memory
Detection
Sensors
Types
Width
Thickness
Label Roll Diameter
Core Diameter
Types
Width
Ribbon
Length
Core Diameter
Programming Language
Media
Software
Resident Fonts
Label Design
HPRT BarTender Ultralite
Seagull Driver
Windows 2000, Vista,7,8,10
Bitmap Fonts
TTF Fonts
90°, 180°, 270° rotatable, single characters 90°, 180°, 270°
rotatable
Asian Fonts
16x16, 24x24. Traditional Chinese, Simplified Chinese,
Japanese, Korean
Code Pages
1D
2D
Rev.1.0
Fonts 0-8 / Fonts A-H,0,GS,P-V 90°, 180°, 270°
rotatable. 10 times maximum expandable in horizontal and
vertical directions.
Monotype CG Triumvirate™ scalable true type font
Bitmap Fonts
Download Fonts
Barcode
Parameter
DOS437,720,737,755,775,850,852,855,856,857,858,860,86
2,863,864,865,866,
Windows1250,1251,1252,1253,1254,1255,1256,1257,1258
ISO8859-1,-2,-3,-4,-5,-6,-8,-9,-15
DBCS 932 (JIS), 936(GBK), 949 (Koran), 950(BIG5)
Code 39, Code 93, Code 128UCC, Code 128 subset A, B, C,
Codabar, Interleave 2 of 5, EAN-8, EAN-13, EAN-128,
UPC-A, UPC-E, EAN and UPC 2 (5) digits add-on, MSI,
PLESSEY, POSTNET, RSS-Stacked, GS1 DataBar, Code 11
PDF417, Maxicode, DataMatrix, QR Code, Aztec
8
PR-600 Series HPRT-HT100 User Manual
(2/2)
Items
Interfaces
Standard
USB, RS232, Ethernet
Option
Bluetooth, WiFi (distributor install)
Operation Panel
Feed button with tri-color LED
AC/DC switching power adapter
I/P: AC100-240V, 50/60Hz, O/P: DC 24V/2.5A
Power
Environment
Physical
Characteristics
Operation
41℉(5℃)-104℉(40℃)，30%-85%(non-condensing)
Storage
-4℉(-20℃)-122℉(50℃)，10%-90%(non-condensing)
Dimension(L*W*H)
240*198*171mm
Weight
2.26kg (excluding consumables)
External label roll holder for 8’’ (203mm) OD label rolls
Electric cutter module
Label dispenser module
Options & Accessories
Agency Approvals
Parameter
CCC, FCC, CE
※Please refer to the attachment for the detailed information of CE and FCC.
Rev.1.0
9
PR-600 Series HPRT-HT100 User Manual
Chapter 3 Installation & Usage
3.1 Media Loading
3.1.1 Paper Roll Loading
1.Pull and lift the cover.
2.Pull the roll holders open and place the roll between them.
Rev.1.0
10
PR-600 Series HPRT-HT100 User Manual
3.Press down the locking tab.
4.Pass the labels through label guides and adjust label guides to label’s width.
Note: If your printer is under Thermal Line Printing Method, press down the
printer cover until it snaps closed. Otherwise, continue the procedure in chapter
3.1.2.
Rev.1.0
11
PR-600 Series HPRT-HT100 User Manual
3.1.2 Ribbon Loading
1. After putting rewind spindle through printhead module, insert the right side of
supply spindle into the rear pin, and then insert the left side into the rear wheel.
Then do the same procedure for the ribbon rewind spindle.
2. Rotate the rear ribbon wheel until the ribbon is pulled tightly.
Rev.1.0
12
PR-600 Series HPRT-HT100 User Manual
3. Press the lock and close the cover slightly.
4. Press down the cover until it snaps closed.
Rev.1.0
13
PR-600 Series HPRT-HT100 User Manual
3.1.3 External Paper Roll Loading
If the paper roll is extremely
large, users can load the paper
roll outside (See the graph at
right). Pass the paper through
the external feed slot and then
through the paper guides.
Adjust the paper guides
according to the paper width.
Rev.1.0
14
PR-600 Series HPRT-HT100 User Manual
3.2 Power Connection
1.Make sure the printer’s power switch is in the off position.
2.Connect the AC adapter to power receptacle.
3.Connect the power cord to AC adapter.
4.Connect the other end of power cord to the outlet.
Note：

Use the original power adapter only. Avoid the damage caused by
charging improperly.

Please unplug the printer power cord if it is not in use for a long time.
Rev.1.0
15
PR-600 Series HPRT-HT100 User Manual
3.3 Peripherals Connection
3.3.1 Interface Cable Connection
The standard for the printer’s interface cable shows in the following.
- USB B-Type Cable
- RS-232C Cable
- RJ45 Cable
Please follow the instructions to connect the cable.
1. Make sure the printer is turned off.
2. Please plug in the cables.
-Insert the USB B-Type cable into the USB port.
-Insert the RS-232C cable into the serial port.
-Insert the RJ45 cable into the ethernet port.
3.3.2 Bluetooth Connection
PDA with Bluetooth interface, laptop and other information terminals can drive the
mobile thermal printer. Instructions as follows:
1. Power on printer.
2. Primary device search for outer Bluetooth devices.
3. If there are some outer Bluetooth devices, choose HT100/130.
4. Finish pairing.
Detailed pairing methods, please refer to primary devices Bluetooth Names. After
pairing, primary devices with virtual Bluetooth interface (smart phone , pocket PC,
palm, notebook) can drive mobile thermal printer to print through such virtual
Bluetooth interface.
Note: The original code is 1234.
Rev.1.0
16
PR-600 Series HPRT-HT100 User Manual
3.4 Detection
When printing paper, the moveable label sensor is used to detect paper. The label
sensor moves differently when using various kinds of paper. If user moves the sensor
improperly, paper may not be detected, therefore the printer could not print paper.
The following instructions tell users how to use label sensor correctly. Please read it
carefully.
3.4.1 Continuous Paper
When printing continuous paper (Figure 1), the sensor shall be aimed at the left
photoelectric hole (Figure 2), which is the original position.
Figure 1 (Continuous Paper)
Rev.1.0
17
PR-600 Series HPRT-HT100 User Manual
Figure 2 (Left)
Rev.1.0
18
PR-600 Series HPRT-HT100 User Manual
3.4.2 Labels
When printing labels (Figure 3) or double-row labels (Figure 4), the sensor shall be
aimed at the left photoelectric hole (Figure 5), which is the original position.
Figure 3 (Labels)
Figure 4 (Double-row Labels)
Rev.1.0
19
PR-600 Series HPRT-HT100 User Manual
Figure 5 (Left)
Rev.1.0
20
PR-600 Series HPRT-HT100 User Manual
3.4.3 Punched Hole Label
When printing punched hole labels, move the sensor until it’s aimed at the right
photoelectric hole (Figure 6).
Figure 6 (Right)
Rev.1.0
21
PR-600 Series HPRT-HT100 User Manual
3.4.4 Blackmark Paper
When printing blackmark paper (Figure 7), the sensor shall be aimed at the position of
black mark (Figure 8).
Figure 7 (Blackmark Paper)
Figure 8 (aimed at blackmark’s position)
Rev.1.0
22
PR-600 Series HPRT-HT100 User Manual
3.5 Operation Panel
1.FEED button
Turn on the printer. Press the feed button, and printer will automatically feed a label
under “Label Mode”. Press the feed button, and the printer will feed the fixed distance
under “Continuous Mode”.
When the printer is printing, press the feed button so that the printing job pauses. At
that time the LED indicator is white. When press this button again, the printing job
continues.
2.Description of indicator status
Rev.1.0
Color
Action
Indicator Status
Blue
Lit on
Ready
Blue
Slow flash
Dump mode
Purple
Lit on
Overheat of printhead
Purple
Slow flash
Ribbon out
Red
Lit on
Head up
Red
Slow flash
Paper out or paper jam or label’s
separation
Red
Quick flash
Abnormal label calibration
Orange
Lit on
Out of ready
Orange
Quick flash
Data is written on flash
Green
Lit on
Printing
Green
Slow flash
Pause of printing
Green
Quick flash
Receiving data
23
PR-600 Series HPRT-HT100 User Manual
3.6 Basic Function
3.6.1 Power On/ Power Off
Press “O” to power off the printer. Press “l”to power on the printer.
3.6.2 FEED Button
1.Turn on the printer. Press the feed button, and printer will automatically feed a label
under “Label Mode”. Press the feed button, and the printer will feed the fixed distance
under “Continuous Mode”.
2.When the printer is printing, press the feed button so that the printing job pauses.
At that time the LED indicator is white. When press this button again, the printing job
continues.
3.6.3 Quick Calibration
Note: Users must carry out the calibration under the conditions below:
➢
➢
➢
➢
➢
➢
The first time to use the printer since installation;
The first time to use the printer since sensor cleaning;
Reuse the printer when it has not been used for a long time;
Change a new type of media;
Printer cannot recognize the mark;
Huge change of the operating environment;
Calibration method:
1.Carry out the calibration manually.
When printer is ready, press the FEED button for 3 seconds until the status
indicator(Blue) flashes twice. Then release the button, and printer will start to do the
calibration. When printer does the calibration under Continuous Media Mode, the
calibration is invalid.
2.Carry out calibration by printer utility tool. Please refer to detailed information in
“Chapter 6 Label Printer Utility Instructions”.
Note: After the quick calibration, users could open the printer cover to pull
back the learned paper in avoid of paper wasting.
Rev.1.0
24
PR-600 Series HPRT-HT100 User Manual
3.6.4 Print Self-test Page
The self-test checks the printer’s current settings, status and whether the printer has
any problems or not.
1.Printing Manually
1) Make sure the roll is loaded properly.
2) Make sure the top cover of the printer is closed properly. Then turn on the printer.
3) When the printer is ready, press the feed button continuously. As soon as the
indicator flashes (green) once, loosen the button. Then the printer starts to print
the self-test page.
2.Printing by Windows Driver Program
1) Install the Windows Driver program.
2) Set the “Interface” as the type you use.
3) Use the Windows Driver Program to print out the “Self-test page”.
4) Please refer to “Chapter 7 Seagull Windows Driver Instructions” for more detailed
information.
3.Printing by HPRT BarTender Ultralite Program
1) Install the HPRT BarTender Ultralite program.
2) Edit a new label and print it.
3) Please refer to “Chapter 8 BarTender Ultralite Instructions” for more detailed
information.
Rev.1.0
25
PR-600 Series HPRT-HT100 User Manual
Chapter 4 Interface
4.1 USB Interface
PIN
1
2
3
4
SIGNAL NAME
VBUS
DD+
GND
4.2 Other Optional Interfaces
 Serial Port
Rev.1.0
PIN
SIGNAL NAME
1
2
3
4
5
6
7
8
9
+5VDC
TXD
RXD
GND
RTS
CTS
RTS
26
PR-600 Series HPRT-HT100 User Manual
 Ethernet Port
Rev.1.0
PIN
SIGNAL NAME
1
2
3
4
5
6
7
8
TX+
TXRX+
RX-
27
PR-600 Series HPRT-HT100 User Manual
Chapter 5 Maintenance & Adjustment
Adhesives and coatings of the media can transfer to the printer parts over time along
the media path including the thermal print head and media sensor. This build-up can
accumulate dust and debris. Failure to clean the print head, media path, and media
sensor could result in inadvertent loss of labels, label jams and possible damage to the
printer.




Note:
Make sure to turn off the printer prior to cleaning.
As the print head gets hot during printing, if intending to clean the print head,
turn the printer off and wait approximately 2~3 minute before commencement.
When cleaning the print head, take care not to touch the heated portion of the
print head. Print Head is susceptible to damage from static electricity, etc. So it is
strongly recommended to wear hand gloves during cleaning progress.
Take care not to allow the print head become scratched and/or damaged in any
way.
5.1 Cleaning Media Sensor
Debris or dirt on the paper sensor can cause a miss-read or unstable detection of the
label gap. Clean with a cotton bud dampened with alcohol.
5.2 Cleaning Thermal Print Head
Thermal Paper stock on the print head, which degrades print quality. Clean the print
head with methanol or isopropyl alcohol and a cotton bud. Do not touch the heating
elements with your fingers.
1) Open the Printer Cover and then use the cleaning pen to clean the head in the
direction from the center of the head to two sides.
2) After cleaning the head, do not use the printer until the alcohol used for cleaning
evaporates completely (1~2 min) and the printer has completely dried.
3) Perform the cleaning process each time the paper roll is replaced to prevent print
quality deterioration.
28
PR-600 Series HPRT-HT100 User Manual
5.3 Cleaning Roller and/or Paper Path
1) Open the printer cover and then remove the paper.
2) Remove any dust or foreign substance using dry cloth or cotton swab.
3) Soak the cloth or cotton swab in alcohol for medical use and use it to remove
adhesive foreign substances or other pollution materials.
4) After cleaning the parts, do not use the printer until the alcohol evaporates
completely (1~2 min) and the printer has completely dried
Note: Clean the parts when print’s quality or label detection degrades.
Rev.1.0
29
PR-600 Series HPRT-HT100 User Manual
Chapter 6 Printer Utility Tool Instructions
6.1 Installation Preparation
Download application program in CD. eg: HPRTUtilityForLabel_Channel V2.0.0.3.
6.2 Usage
Note: The screen may vary slightly by different operating systems and models.
Take printer HT100 as example. Please refer to printer HT100 when using printer
HT130.
(1) Download “HPRTUtilityForLabel_Channel V2.0.0.3” in CD.
(2) Then open the “HPRTUtilityForLabel_Channel.exe”.
Rev.1.0
30
PR-600 Series HPRT-HT100 User Manual
(2) Add/Modify/Delete Printer, Connect Test.
●Click “Add Printer”. Choose the printer and port (eg: USB), then click “OK”, showed in
“Printer List”.
Rev.1.0
31
PR-600 Series HPRT-HT100 User Manual
●Click “Modify Printer”. Choose the printer and port(eg: COM1), then click “OK”,
showed in “Printer List”.
Rev.1.0
32
PR-600 Series HPRT-HT100 User Manual
●Click “Delete Printer”. Click “OK” to delete the printer, and click “Cancel” to cancel
the command.
●Click “Connect Test” to test whether the connection is successful or not.
If connection succeeds, it shows as follows.
If connection fails, it shows as follows.
Note:
1.Connect printer to power first, then choose one port (depended on the printer you
bought) to connect to the PC. Much more information of connecting method is
contained in “3.3 Peripherals Connection”.
2.When connection fails, please check the connection and whether it matches or
not.(When USB port is used, it is better to connect one printer only.)
Rev.1.0
33
PR-600 Series HPRT-HT100 User Manual
(3)Function.
●Click “Printer Information”, showing printer information.(varies by different printers)
●Click “Print Test Text”. Type the text and set up the printing range. Click “Print”, then
printer starts to print the test text.
●Click “Print Self Information”, then printer starts to print self-test page.
●Click “Label Auto Learn”, then printer will carry out the calibration.
Rev.1.0
34
PR-600 Series HPRT-HT100 User Manual
●Click “Parameter Setting”. User can set up the BT config, print type, paper mode and
so on.
Click “Set”, and back to the main menu.
●Click “Model Print Test”, then printer starts to print models.
●Click “Restore Factory Settings”. Click “OK” to restore factory settings, and click
“Cancel” to cancel the command.
(4)Click “Quit”, then finish the settings.
Rev.1.0
35
PR-600 Series HPRT-HT100 User Manual
Chapter 7 Seagull Windows Driver Instructions
7.1 Introduction
The following operating systems are supported:
Microsoft Windows 10 (32 bit/64 bit)
Microsoft Windows 8 (32 bit/64 bit)
Microsoft Windows 7 SPI (32 bit/64 bit)
Microsoft Windows Vista SP2 (32 bit/64 bit)
Microsoft Windows Server 2012(64 bit)
Microsoft Windows Server 2008 R2
Microsoft Windows Server 2008 SP2(32 bit/64 bit)
Microsoft Windows Server 2003 R2 SP2(32 bit/64 bit)
7.2 Installation Preparation
Download Seagull Windows Driver application program in CD.
Rev.1.0
36
PR-600 Series HPRT-HT100 User Manual
7.3 Installation
Note:
 Under different operating systems, the screen may be slightly different. Take
Windows 7 as example.
 Take printer HT100 as example. Please refer to printer HT100 when using printer
HT130.
 To avoid the prevention, recommend to close the security software before
installation.
1.Select one interface to connect your printer to computer.
2.Turn on the printer and check if it is connected to computer successfully.
3.Double click Seagull Windows Driver
.
4.Read and agree the license agreement. Then click “Next”.
Rev.1.0
37
PR-600 Series HPRT-HT100 User Manual
5.Choose the installation directory, then click “Next”.
6.Click "Finish".
Rev.1.0
38
PR-600 Series HPRT-HT100 User Manual
7.Choose "Install printer drivers", then click "Next".
Note: If you have connected the printer to computer, it will detect and install
the driver automatically. (eg.: USB port)
8.Choose "Install a driver for a Plug and Play printer, then click "Next".
Rev.1.0
39
PR-600 Series HPRT-HT100 User Manual
9.Enter a name for this printer, then click "Next".
10.Click"Finish".
Rev.1.0
40
PR-600 Series HPRT-HT100 User Manual
11.Click "Close", and the printer driver is installed successfully.
12.After installation, the icon will be found in ”Start”→“Devices and Printers”.
Note:
1.If you have already installed the driver (No matter what kind of ports), it will
generate a USB port automatically when connecting the printer to computer.
2.Any problems exist, please use our utility tool in CD.
Rev.1.0
41
PR-600 Series HPRT-HT100 User Manual
7.4 Usage
7.4.1 Printing Preferences
1.Click “Start”→“Devices and Printers”. Right click the icon and choose “Printing
preferences”.
Rev.1.0
42
PR-600 Series HPRT-HT100 User Manual
2.According to different needs, set up the page.
Rev.1.0
43
PR-600 Series HPRT-HT100 User Manual
●Click “Stock”→”Name”, and choose the paper type.
●Click “New Stock”, and set up a new stock.
Rev.1.0
44
PR-600 Series HPRT-HT100 User Manual
●Click “Edit Stock”, and edit the stock.
●Click “Delete Stock”, and delete the stock.
Rev.1.0
45
PR-600 Series HPRT-HT100 User Manual
●Choose “Orientation” or “Effects”, showed in the “Preview”.
Rev.1.0
46
PR-600 Series HPRT-HT100 User Manual
●Click “Preset”→“Name”, and back to the default settings.
●Click “Manage”, and change the settings.
Rev.1.0
47
PR-600 Series HPRT-HT100 User Manual
3.Click “Graphics”, and edit the pictures.
4.Click “Stock”.
Rev.1.0
48
PR-600 Series HPRT-HT100 User Manual
●Click “Method”, and choose the printing method.
●Click “Type”, and choose the printing type.
Rev.1.0
49
PR-600 Series HPRT-HT100 User Manual
●Click “Post-Print Action”, and choose the method of media handling.
Rev.1.0
50
PR-600 Series HPRT-HT100 User Manual
7.4.2 Printer Properties
1.Click “Start”→“Devices and Printers”. Right click the icon and choose “Printer
properties”.
Rev.1.0
51
PR-600 Series HPRT-HT100 User Manual
2.Click “General”→“Print Test Page”, and printer will print labels with current settings.
Rev.1.0
52
PR-600 Series HPRT-HT100 User Manual
3.Click “Ports”, then choose the port needed.
7.4.3 Label’s Width
USER(4.00 in×4.00 in)
2×4(2.00 in×4.00 in)
4×4(4.00 in×4.00 in)
4×6(4.00 in×6.00 in)
Rev.1.0
53
PR-600 Series HPRT-HT100 User Manual
7.5 Removing
Note: Please turn off the printer or unplug the USB cable before removing the
driver.
1.Double click Seagull Windows Driver
.
2.Read and agree the license agreement. Then click “Next”.
Rev.1.0
54
PR-600 Series HPRT-HT100 User Manual
3.Choose the installation directory, then click “Next”.
4.Click"Finish".
Rev.1.0
55
PR-600 Series HPRT-HT100 User Manual
5.Select “Remove printer drivers”, then click “Next”.
6.Select “Remove printers”, then click “Next”.
Rev.1.0
56
PR-600 Series HPRT-HT100 User Manual
7.Select printer’s name, then click “Next”.
8.Please unplug the USB cable or turn off the printer when appearing the following
prompt.
Rev.1.0
57
PR-600 Series HPRT-HT100 User Manual
9.Click “Finish”.
10.Restart the computer when appearing the following prompt or continue step 11.
Rev.1.0
58
PR-600 Series HPRT-HT100 User Manual
11.Click “Close”. The driver has been removed successfully.
Rev.1.0
59
PR-600 Series HPRT-HT100 User Manual
Chapter 8 BarTender Ultralite Instructions
8.1 Introduction
This chapter provides instructions on BarTender Ultralite program according to PC
operating systems(OS).
The followings are supported.
Microsoft Windows 10 (32 bit/64 bit)
Microsoft Windows 8 (32 bit/64 bit)
Microsoft Windows 7 SPI (32 bit/64 bit)
Microsoft Windows Vista SP2 (32 bit/64 bit)
Microsoft Windows Server 2012(64 bit)
Microsoft Windows Server 2008 R2
Microsoft Windows Server 2008 SP2(32 bit/64 bit)
Microsoft Windows Server 2003 R2 SP2(32 bit/64 bit)
8.2 Installation Preparation
Download BarTender Ultralite application program in CD.
Rev.1.0
60
PR-600 Series HPRT-HT100 User Manual
8.3 Installation
Note：



Under different operating systems, the screen may be slightly different. Take
Windows 7 as example.
Take printer HT100 as example. Please refer to printer HT100 when using printer
HT130.
To avoid the prevention, recommend to close the security software before
installation.
1.Double click the application program
2.Select language, then click "OK".
.
3.Click "Install".
Rev.1.0
61
PR-600 Series HPRT-HT100 User Manual
4.Click “Next”.
5.Read and accept the license agreement, then click "Next".
Rev.1.0
62
PR-600 Series HPRT-HT100 User Manual
6.Select "Features" and installation location, then click "Next".
7.Click "Install".
Rev.1.0
63
PR-600 Series HPRT-HT100 User Manual
8.Click "Finish".
9.Back to desktop, and you will see the icon of BarTender Ultralite. Double click it and
get down to use.
Rev.1.0
64
PR-600 Series HPRT-HT100 User Manual
8.4 Usage
8.4.1 Page Settings
1.Double click the icon, then choose the edition. Click “OK”. (The edition may be
changed according to different needs.)
2.Click “Start a new BarTender document”.
Rev.1.0
65
PR-600 Series HPRT-HT100 User Manual
3.Choose “Blank Template”, then click “Next”.
4.If the predefined stocks don’t meet your need, tick “Specify Custom Settings”. Then
click”Next”.
Rev.1.0
66
PR-600 Series HPRT-HT100 User Manual
5.Tick “Single item per page”, then click “Next”. (If you print multiple labels, tick
“Multiple columns and/or rows of items per page ”.)
6.Edit the side edges, then click “Next”.
Rev.1.0
67
PR-600 Series HPRT-HT100 User Manual
7.Choose the item shape, then click “Next”.
8.Edit the template size, then click “Next”.
Rev.1.0
68
PR-600 Series HPRT-HT100 User Manual
9.Based on your need, edit the template background. Then click ”Next”.
10.Finish the settings, showed in the “Review” and “Preview”. Then click “Finish”.
Rev.1.0
69
PR-600 Series HPRT-HT100 User Manual
8.4.2 label Edit
1.Click the icon of code
.
2.Choose the code, then click “Select”.
3.Click the blank, showing the code.
Rev.1.0
70
PR-600 Series HPRT-HT100 User Manual
4.Double click the code and edit it. User can set up the size, font, border and so on.
Finishing the changes, click “Close”.
5.Click the icon of character
Rev.1.0
, then enter the text.
71
PR-600 Series HPRT-HT100 User Manual
6.Click the icon of picture
, then edit the pictures.
7.Compose the text.
8.Finish all the settings. Click “Print” and a new label will be printed.
Rev.1.0
72
PR-600 Series HPRT-HT100 User Manual
ATTACHMENT
Rev.1.0
73
PR-600 Series HPRT-HT100 User Manual