download link

T12C
Installation Manual
MAEN082E, 2014-04
English
Foreword
Installation manual for T12C
Foreword
All operator panels are developed to satisfy the demands of human-machine
communication. Built-in functions such as displaying and controlling text,
dynamic indication, time channels, alarm and recipe handling are included.
The operator panel works primarily in an object-oriented way, making it easy to
understand and use. Configuration is carried out on a PC using the iX Developer.
The project can then be transferred and stored in the operator panel itself.
Various types of automation equipment such as PLCs, servos or drives can be
connected to the operator panels. In this manual, the term “the controller” refers
to the connected equipment.
This manual explains how to install the operator panel. Please refer to the
iX Developer reference manual for further information.
Order no: MAEN082E
Copyright © 2014-04 Beijer Electronics AB. All rights reserved.
The information in this document is subject to change without notice and is provided as available at the
time of printing. Beijer Electronics AB, including all its group companies, reserves the right to change any
information without updating this publication. Beijer Electronics AB, including all its group companies,
assumes no responsibility for any errors that may appear in this document. Read the entire installation
manual prior to installing and using this equipment. Only qualified personnel may install, operate or repair
this equipment. Beijer Electronics AB, including all its group companies, are not responsible for modified,
altered or renovated equipment. Because the equipment has a wide range of applications, users must acquire
the appropriate knowledge to use the equipment properly in their specific applications. Persons responsible
for the application and the equipment must themselves ensure that each application is in compliance with
all relevant requirements, standards and legislation in respect to configuration and safety. Only parts and
accessories manufactured according to specifications set by Beijer Electronics AB, including all its group
companies, may be used.
BEIJER ELECTRONICS AB, INCLUDING ALL ITS GROUP
COMPANIES, SHALL NOT BE LIABLE TO ANYONE FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE INSTALLATION, USE OR
REPAIR OF THIS EQUIPMENT, WHETHER ARISING IN TORT,
CONTRACT, OR OTHERWISE. BUYER'S SOLE REMEDY SHALL
BE THE REPAIR, REPLACEMENT, OR REFUND OF PURCHASE
PRICE, AND THE CHOICE OF THE APPLICABLE REMEDY SHALL
BE AT THE SOLE DISCRETION OF BEIJER ELECTRONICS AB,
INCLUDING ALL ITS GROUP COMPANIES.
Beijer Electronics, MAEN082E
Contents
Contents
1 Safety Precautions .......................................................
1.1
General ...........................................................
1.2
During Installation ..............................................
1.3
During Use .......................................................
1.4
Service and Maintenance ........................................
1.5
Dismantling and Scrapping .....................................
1.6
Appearance of Air in Touch Screen .............................
2 Installation ...............................................................
2.1
Space Requirements .............................................
2.2
Installation Process ..............................................
2.2.1
2.2.2
Connections to the Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Other Connections and Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3 Hardware Replacement .................................................
3.1
Replacing the Fan and Filter .....................................
3.2
Replacing the 2.5” SATA Mass Storage .........................
3.3
Replacing a CompactFlash or CFast Memory Card ...........
3.4
Replacing the Battery ............................................
4 Technical Data ...........................................................
5 Chemical Resistance ....................................................
5.1
Metal Casing .....................................................
5.2
Touch Screen and Overlay .......................................
5.2.1
5.2.2
5.2.3
4
4
4
5
5
5
5
6
6
7
10
10
12
14
15
16
18
18
19
Autotex F157/207 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Touch Screen Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Touchscreen Protective Film . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6 Operator Panel Drawings ..............................................
6.1
Connectors .......................................................
6.2
Communication Ports ...........................................
6.3
T12C Outline ....................................................
7 Additional Installation Tips ............................................
7.1
Grounding the Operator Panel .................................
7.2
Ethernet Connection in the Operator Panel ...................
7.3
To Achieve Better EMC Protection .............................
7.4
Ambient Temperature ...........................................
7.5
Safety .............................................................
7.6
Cable and Bus Termination RS485 .............................
7.7
Boot Priority .....................................................
7.8
Entering BIOS ...................................................
7.9
Reset Switch ......................................................
Beijer Electronics, MAEN082E
21
21
21
23
25
25
26
28
29
30
31
32
32
33
Safety Precautions
1
Safety Precautions
Both the installer and the owner and/or operator of the operator panel must read
and understand this installation manual.
1.1
•
•
•
•
•
•
•
•
•
•
•
•
General
Read the safety precautions carefully.
Check the delivery for transportation damage. If damage is found, notify the
supplier as soon as possible.
The supplier is not responsible for modified, altered or reconstructed
equipment.
Use only parts and accessories manufactured according to specifications of
the supplier.
Read the installation and operating instructions carefully before installing,
using or repairing the operator panel.
Never allow fluids, metal filings or wiring debris to enter any openings in the
operator panel. This may cause fire or electrical shock.
Only qualified personnel may operate the operator panel.
Storing the operator panel where the temperature is lower/higher than
recommended in this manual can cause the LCD display liquid to
congeal/become isotopic.
The LCD display liquid contains a powerful irritant. In case of skin contact,
wash immediately with plenty of water. In case of eye contact, hold the eye
open, flush with plenty of water and get medical attention.
The figures in this manual serves an illustrative purpose. Because of the many
variables associated with any particular installation, the supplier cannot
assume responsibility for actual use based on the figures.
The supplier neither guarantees that the operator panel is suitable for your
particular application, nor assumes responsibility for your product design,
installation or operation.
It is recommended to turn on and shut down the operator panel at least once
before installing any components/cards or before connecting the operator
panel to external devices, like for example serial devices.
1.2
During Installation
•
The operator panel is designed for stationary installation on a plane surface,
where the following conditions are fulfilled:
–
no high explosive risks
–
no strong magnetic fields
–
no direct sunlight
–
no large, sudden temperature changes
•
Install the operator panel according to the accompanying installation
instructions.
Ground the operator panel according to the accompanying installation
instructions.
Only qualified personnel may install the operator panel.
Separate the high voltage, signal and supply cables.
•
•
•
Beijer Electronics, MAEN082E
4
Safety Precautions
•
•
Make sure that the voltage and polarity of the power source is correct before
connecting the operator panel to the power outlet.
Peripheral equipment must be appropriate for the application and location.
1.3
•
•
•
Keep the operator panel clean.
Emergency stop and other safety functions may not be controlled from the
operator panel.
Do not use excessive force or sharp objects when operating the touchscreen.
1.4
•
•
•
•
•
•
•
Service and Maintenance
Only qualified personnel should carry out repairs.
The agreed warranty applies.
Before carrying out any cleaning or maintenance operations, disconnect the
equipment from the electrical supply.
Clean the display and surrounding front cover with a soft cloth and mild
detergent.
Replacing the battery incorrectly may result in explosion. Only use batteries
recommended by the supplier. During the warranty period, the battery needs
to be replaced by an authorized Beijer Electronics service center.
The unit can be reset by using the reset switch located behind the fan.
1.5
•
During Use
Dismantling and Scrapping
The operator panel or parts thereof shall be recycled according to local
regulations.
The following components contain substances that might be hazardous
to health and the environment: lithium battery, electrolytic capacitor and
display.
1.6
Appearance of Air in Touch Screen
The layer structure of the touch screen contains air and in rare cases appearance of
bubbles can arise. This is purely cosmetic and does not affect any functionality
of the operator panel. The appearance can occur under certain environmental
conditions such as temperature, humidity, and atmospheric pressure.
Beijer Electronics, MAEN082E
5
Installation
2
Installation
2.1
Space Requirements
•
•
Maximum installation plate thickness: 8 mm
Space requirements in millimeters when installing the operator panel:
242,2 mm
100 mm
50 mm
50 mm
100 mm
100 mm
340 mm
Note:
The dimensions on the drawing are not proportional.
Caution:
The openings on the enclosure are for air convection. Do not cover these openings.
Beijer Electronics, MAEN082E
6
Installation
2.2
Installation Process
The following is needed:
•
A Torx TX7 screwdriver
1. Unpack and check the delivery. If damage is found, notify the supplier.
Note:
Place the operator panel on a stable surface during installation.
Dropping the operator panel or letting it fall may cause damage.
2. To cut a correct opening for the operator panel, use the cut out dimensions
in the outline drawing. A separate cut out drawing is available for download
from the Beijer Electronics web site. For more information, see sections
Operator Panel Drawings and Technical Data.
3. Secure the operator panel in position by screwing the M4 Torx screw, allowing
the built-in bracket to tighten against the panel:
M4 x 20.7
0.4 Nm
Beijer Electronics, MAEN082E
7
Installation
4. Connect the cables in the specified order, according to the drawing and steps
below.
Caution:
•
The operator panel must be brought to ambient temperature before it is started
up. If condensation forms, ensure that the operator panel is dry before connecting
it to the power outlet.
•
Ensure that the operator panel and the controller system have the same electrical
grounding (reference voltage level), otherwise errors in communication may
occur.
•
Ensure that the voltage and polarity of the power source is correct.
•
Separate high voltage cables from signal and supply cables.
•
Shielded communication cables are recommended.
B
Power
Controller
RS232/
RS422/
RS485
24V DC
24V DC
C
D
A
Ethernet
Connect cable A.
Connect cable B, using an M5 screw and a grounding conductor (as short
as possible), that is sized correctly according to local electrical codes.
–
Connect cable C.
–
Connect cable D. The recommended cross-section of the cable is
2.5 mm2.
5. Carefully remove the laminated film over the operator panel display, to avoid
static electricity that could damage the panel.
–
–
Beijer Electronics, MAEN082E
8
Installation
2.2.1
Connections to the Controller
For information about the cables to be used when connecting the operator panel to
the controller, please refer to the help file for the driver in question.
2.2.2
Other Connections and Peripherals
Cables, peripheral equipment and accessories must be suitable for the application
and its environment. For further details or recommendations, please refer to the
supplier.
Beijer Electronics, MAEN082E
9
Hardware Replacement
3
Hardware Replacement
This section contains instructions on how to replace operator panel hardware.
Only components included in the latest bill of material and spare parts list are
allowed.
3.1
Replacing the Fan and Filter
The following is needed:
•
A new fan
•
A Torx TX10 and a TX20 screwdriver
Note:
Make sure to use adequate ESD protection.
Follow the steps below to replace the fan and fan filter:
1. Power off the operator panel.
2. Remove the fan lid by removing the two M3x6 Torx screws.
3. Remove the fan filter.
Beijer Electronics, MAEN082E
10
Hardware Replacement
4. Remove the fan by removing the two M4x35 Torx screws.
5. Reassemble with new fan and filter in reverse order. Use a maximum torque of
0.4 Nm when fastening the fan screws.
Beijer Electronics, MAEN082E
11
Hardware Replacement
3.2
Replacing the 2.5” SATA Mass
Storage
The following is needed:
•
A new 2.5” SATA mass storage
•
A TX10 Torx screwdriver
Note:
Make sure to use adequate ESD protection.
Follow the steps below to replace the 2.5” SATA mass storage:
1. Power off the operator panel.
2. Remove the front frame assembly by removing the eight M3x8 Torx screws
on the back cover assembly.
Caution:
During disassembly, it is important to take care of the cable between the front and the
rear part. If you disconnect a cable, be sure that the right cable will be in the right
position when assembling.
Note:
The exchange of electronic components is only for experienced professionals.
Incorrect handling of electronic components or cables plugged in wrong, can lead to
the destruction of the device.
3. Remove the four M3x4 Torx screws on the two hard drive brackets. Remove
the two hard drive brackets.
4. Remove the two M3x6 Torx screws that are securing the brackets to the CPU
board.
Beijer Electronics, MAEN082E
12
Hardware Replacement
5. Remove the hard disk drive from the hard drive connection on the CPU
board.
6. Reassemble with the new hard disk drive in reverse order.
1. 2.5” SATA mass storage
2. CompactFlash slot
3. CFast slot
Beijer Electronics, MAEN082E
13
Hardware Replacement
3.3
Replacing a CompactFlash or CFast
Memory Card
The following is needed:
•
A new CompactFlash or CFast memory card.
•
A TX10 Torx screwdriver
Note:
Make sure to use adequate ESD protection.
Follow the steps below to replace a memory card:
1. Power off the operator panel.
2. Follow the instructions in chapter Replacing the 2.5” SATA Mass Storage to
remove the front frame assembly.
3. Install the new memory card in its intended slot illustrated in figure below.
1. 2.5” SATA mass storage
2. CompactFlash slot
3. CFast slot
4. Reassemble in reverse order.
Beijer Electronics, MAEN082E
14
Hardware Replacement
3.4
Replacing the Battery
The following is needed:
•
A new BR 2032 (or CR 2032) battery.
•
A Torx screwdriver
Note:
Make sure to use adequate ESD protection.
Follow the steps below to replace the battery:
1. Power off the operator panel.
2. Follow the instructions in chapter Replacing the Fan and Filter to remove the
fan and access the battery.
3. Replace the battery.
4. Reassemble in reverse order.
Beijer Electronics, MAEN082E
15
Technical Data
4
Technical Data
Parameter
T12C
Front panel, W × H × D
340 × 242 × 79 mm
Cut out dimensions,
W×H
324 × 226 mm
Mounting depth
72 mm (172 mm including clearance)
Standalone mounting
VESA 100 × 100
Note: Maximum screw length for VESA mounting is 5.5 mm.
Usage of longer screws may lead to damage.
Front panel seal
IP 65
Rear panel seal
IP 20
Touch screen
material
Polyester on glass, resistive.
Overlay: Autotex F157 or F207(1).
Touch screen
operations
1 million finger touch operations
Reverse side
material
Powder-coated aluminum
Frame material
Powder-coated aluminum
Weight
4.2 kg
Serial port for
COM1 RS232 and
COM2 RS422/RS485
9-pin D-sub contact with RS232 RTS/CTS, chassis-mounted
female with standard locking screws 4-40 UNC
Note: RS422 Interface is not available yet.
Serial port for
COM3 RS232 and
COM4 RS422/RS485
9-pin D-sub contact with RS232 RTS/CTS, chassis-mounted
female with standard locking screws 4-40 UNC
Note: RS422 Interface is not available yet.
Ethernet
2 × 10/100/1000 Base-T (shielded RJ45)
USB
4 × USB Host 2.0, max output current 500 mA
Processor
Intel® Celeron® B810E (2 × 1.6 GHz), 2 MB L2 Cache,
Intel® QM67 Chipset
Optional: Intel® Core™ i3 2310E (2 × 2.1 GHz) (Hyperthreading), 3 MB L2 Cache, QM67 Chipset
Optional: Intel® Core™ i7 2715QE (4 × 2.1 GHz) (Turbo
2.0, Hyperthreading), 6 MB L2 Cache, QM67 Chipset
*for exact configuration please see price list
External storage
media
via USB
Memory RAM
2 GB* / 4 GB* DDR-3 SO-DIMM 1333 MHz
*depending on Processor Module
LED
1 × multi-color
Real time clock
Yes (on chip)
Battery
Lithium battery type BR 2032 (or CR 2032), exchangeable
Power consumption
at rated voltage
107 W
Fuse
10 A
Beijer Electronics, MAEN082E
16
Technical Data
Parameter
T12C
Power supply
DC input range: 18 to 32 V DC (140 W) ATX standard
CE: The power supply must conform with the requirements
according to IEC 60950 and IEC 61558-2-4.
UL and cUL: The power supply must conform with the
requirements for class II power supplies.
Display
TFT-LCD with LED backlight. 1280 × 800 pixels,
16.7 million colors
VGA
1 × VGA: resolution max. 2048 × [email protected]
DVI
1 × DVI-D single Link: Resolution max. 1600 × 1200 or
1920 × 1200 (with reduced blanking)
Active area of
display, W × H
261.12 × 163.2 mm
Operating
temperature
0 °C to +50 °C
Storage temperature
-20 °C to +70 °C
Relative humidity
<85% non-condensed
Approvals and
certifications
Information is available on the web site
www.beijerelectronics.com
(1) See section Chemical Resistance for more information.
Beijer Electronics, MAEN082E
17
Chemical Resistance
5
Chemical Resistance
5.1
Metal Casing
The frame and casing material is powder-coated aluminum. This powder paint
withstands exposure to the following chemicals without visible change:
Acetic acid 10%
Phosphoric acid 4%
Citric acid 10%
Phosphoric acid 10%
Diesel
Sea water
Distilled water
Sodium chloride 2%
Edible oil
Sodium chloride 20%
Fuel oil
Sulphuric acid 20%
Hydrogen peroxide 3%
Tap water
The powder paint shows limited resistance to the following chemicals at room
temperature:
Butanol
Nitric acid 3%
Hydrochloric acid 5%
Nitric acid 10%
Isopropyl alcohol
Phosphoric acid 43%
Na-hypochlorite 10%
Turpentine
Sodium hypochlorite
Note:
If exposure to any of the above chemicals is demanded, it is recommended to first test
the chemical in a hidden spot of the metal casing.
The powder paint shows little or no resistance to the following chemicals at room
temperature:
Acetic acid, conc.
Methyl-ethyl ketone
Toluene
Acetone
Nitric acid 30%
Trichlorethylene
Ammonia 5%
Phenol
Xylene
Ammonia, conc.
Sodium hydroxide 5%
97 octane unleaded petrol
Ethyl acetate
Sodium hydroxide 30%
98 octane leaded petrol
Beijer Electronics, MAEN082E
18
Chemical Resistance
5.2
Touch Screen and Overlay
5.2.1
Autotex F157/207
Autotex F157 or F207 covers the overlay surrounding the screen.
Solvent Resistance
Autotex F157/F207 withstands exposure of more than 24 hours duration under
DIN 42 115 Part 2 to the following chemicals without visible change:
Ajax / Vim in solution
Downy / Lenor(1)
Phosphoric acid (<30%)
Alkalicarbonate
solution(1)
Ethanol
Potassium ferricyanide
Ammonia (<40%)(1)
Glycerine
Potassium hydroxide (<30%)
Acetic acid (<50%)
Glycol
Pure Turpentine
Ariel powder in
solution(1)
Gumption(1)
SBP 60/95(1)
Bleach(1)
Hydrochloric acid (<36%)
Sulfuric acid (<10%)
Castor oil
Linseed oil
Tomato ketchup
Caustic soda (<40%)(1)
Methanol
Trichloroacetic acid (<50%)
Cutting oil
Nitric acid (<10%)
White Spirit
Cyclohexanol
Paraffin oil
Windex(1)
Diacetone alcohol
Persil powder in solution(1) Wisk
Diesel
Petroleum spirit(1)
Acetonitrile
(1) Extremely faint glossing of the texture was noted.
Autotex withstands DIN 42 115 Part 2 exposure of up to 1 hour duration to glacial
acetic acid without visible change.
Autotex is not resistant to high pressure steam at over 100 °C or the following
chemicals:
Concentrated mineral acids
Benzyl alcohol
Concentrated caustic solution
Methylene chloride
Beijer Electronics, MAEN082E
19
Chemical Resistance
5.2.2
Touch Screen Surface
The touch screen surface on the operator panel withstands exposure to the
following solvents without visible change:
Solvents
Time
Acetone
10 minutes
Isopropanol
10 minutes
Toluene
5 hours
5.2.3
Touchscreen Protective Film
Autotex
It is recommended to use the Autoflex EBA 180Ltouch display protection film,
that can be ordered from Beijer Electronics.
Outdoor Use
In common with all polyester based films, Autoflex EBA 180L is not suitable for
use in conditions of long-term exposure to direct sunlight.
Note:
The layer structure of the touch screen contains air and in rare cases appearance of
bubbles can arise. This is purely cosmetic and does not affect any functionality of the
panel. The appearance can occur under certain environmental conditions such as
temperature, humidity, and atmospheric pressure.
Beijer Electronics, MAEN082E
20
Operator Panel Drawings
6
Operator Panel Drawings
6.1
Connectors
1
Pos.
2
3
4
5
6
7
8
9
Connector
Description
1
DVI
External monitor
2
VGA
External monitor
3
COM 3/4
Communication Ports
4
COM 1/2
Communication Ports
5
LAN Port B
1 × 10/100/1000 Base-T (shielded RJ45); Intel 82574
6
LAN Port A
1 × 10/100/1000 Base-T (shielded RJ45); Intel 82574
7
USB
2 × USB Host 2.0, max output current 500 mA
8
USB
2 × USB Host 2.0, max output current 500 mA
9
Power supply
DC input range: 18-32 V DC (140 W) ATX standard
6.2
Pin
Communication Ports
Serial port, 9-pin female
COM1
COM2
RS422 Tx+
Serial port, 9-pin female
COM3
RS422 Tx+
1
-
2
RS232 RxD
-
RS232 RxD
-
3
RS232 TxD
-
RS232 TxD
-
4
-
RS422 Rx+
-
RS422 Rx+
5
GND
GND
GND
GND
6
-
7
RS232 RTS
-
-
RS422 RTS+
8
RS232 CTS
-
-
RS422 RTS-
9
-
RS422 Rx-
-
RS422 Rx-
RS485 Tx+/Rx+
RS422 TxRS485 Tx-/Rx-
-
COM4
-
RS485 Tx+/Rx+
RS422 TxRS485 Tx-/Rx-
Note: RS422 Interface is not available yet.
Beijer Electronics, MAEN082E
21
Operator Panel Drawings
Note:
In order to utilize two communication ports on the same physical port, the Y-split cable
CAB109 must be used.
Drawing for external cable CAB109 (drawing # Z7100-029E) is available on the web site:
www.beijerelectronics.com
Beijer Electronics, MAEN082E
22
Operator Panel Drawings
6.3
T12C Outline
242
340
max. 8 mm
7
72
9
224
9
9
322
9
Beijer Electronics, MAEN082E
23
Operator Panel Drawings
Note:
A Step CAD file is available on the web site www.beijerelectronics.com
Beijer Electronics, MAEN082E
24
Additional Installation Tips
7
Additional Installation Tips
When experiencing communication problems in for example noisy environments
or when operating close to temperature limits, the following recommendations
are to be noticed.
7.1
Grounding the Operator Panel
Mounting plate in the cabinet
Door
Operator panel
3
2
Power supply
1
24 V DC
Ferrite core
5
6
4
5350
The operator panel’s mounting clamps do not provide a secure grounding
connection between the panel and the device cabinet, see 1 in drawing above.
1. Connect a wire that is sized correctly according to local electrical codes
between the operator panel’s quick-connect plinth and the panel’s chassis, see
2 in drawing above.
2. Connect a wire or grounding braid that is sized correctly according to local
electrical codes between the operator panel’s chassis and the closest grounding
point on the door, see 3 in drawing above.
3. Connect a strong but short grounding braid between the door and the device
cabinet, see 4 in drawing above.
4. Twist the cables onto the 24 V DC feed, see 5 in drawing above.
2 turns around the ferrite core provide 4 times the suppression of 1 turn.
3 turns around the ferrite core provide 9 times the suppression of 1 turn.
A ferrite core suppresses disturbances to the 24 V feed, see 6 in drawing above.
Beijer Electronics, MAEN082E
25
Additional Installation Tips
Note:
The grounding wires should be short and the conductor should have a large area.
A long, thin grounding wire has a very high impedance (resistance) at high frequencies
and will not guide disturbances to the ground.
Multi-wire conductors are better than single wire conductors with the same area.
A braided conductor wire with the same area is even better. The best is a short, thick
grounding braid.
7.2
Ethernet Connection in the
Operator Panel
Industrial Ethernet
RJ45
RJ45
1
RJ45
RJ45
Operator panel
RJ45
3
2
Operator panel
RJ45
4
Shielded
1-1
2-2
3-3
Short and
unshielded
Operator panel
RJ45
8-8
5
Operator panel
RJ45
0.1 μF
250 V
In some industrial units for Ethernet, the RJ45 contact’s shield is connected to the
chassis via a capacitor, see 1 in drawing above.
The operator panel’s Ethernet shield is directly connected to the chassis, see 2 in
drawing above.
1. Check whether the other Ethernet unit has its shield directly grounded or
grounded via a capacitor.
Note:
In many cases, connecting the shielded Ethernet cabling to the chassis at both ends is
inappropriate. Hum or grounding loops can occur. Unshielded cabling may even result
in fewer communication errors.
Beijer Electronics, MAEN082E
26
Additional Installation Tips
A good solution may be to use a shielded Ethernet cable, but to connect the shield
at one end only.
One option is to break the shield, see 3 in drawing above.
A more elegant method is to expand the shielded Ethernet cabling with a piece of
unshielded Ethernet cable, see 4 in drawing above.
The shield can be grounded via an external 0.1 μF/250 V plastic capacitor, see 5 in
drawing above. This will connect the HF transients to ground.
Beijer Electronics, MAEN082E
27
Additional Installation Tips
7.3
•
•
•
•
•
•
•
To Achieve Better EMC Protection
Use shielded cables for RS232 communication.
Use twisted pair and shielded cabling for RS422 and RS485.
Use the cabling intended for the bus type; Ethernet, Profibus, CC-Link,
CAN, Device Net etc.
Install and connect according to applicable specifications for the relevant bus
standard.
Use shielded cabling for Ethernet, preferably with foil and a braided shield.
D-sub covers should be shielded, and the shield should be connected to the
cover 360° where the cable enters.
Connect the shield at both ends.
Shielded cable
0.1 μF/250 V
Ground plane 1
Ground plane 2
Not same potential
Ground plate in another building
Ground plate
With longer distances, there is a risk that the ground potential may be different.
In that case, the shield should only be connected at one end. A good alternative
is to connect the other end of the shield to the ground via a 0.1 μF/250 V plastic
capacitor. Both ends are then connected to the ground in terms of HF, but only
connected to the ground at one end in terms of LF, thus avoiding the 50/60 Hz
grounding loops.
Metal cabinet
Metal cabinet
Terminal or connector
Short distance
Terminal or connector
EMC cable gland
Shielded cable
Cable clamp
in steel
Plastic cable gland
Shielded cable
1. Use an EMC cable gland or regular plastic cable gland, remove the outer jacket
and connect the shield to the installation plate with a 360° metal cable clamp.
2. Place the 24 V DC and communications cabling in one cable trunk/cable duct
and 230/380 V AC in another. If the cables need to be crossed, cross them at
90° only. Avoid combining the cabling for stronger 24 V DC outputs with
the communication cabling.
Ferrite cores that are snapped onto the shielded cabling may remove minor
disturbances. Large ferrite pieces that are snapped onto unshielded cabling and
where the wires go 2-4 times around the cores are approximately 5-25 times more
efficient.
Beijer Electronics, MAEN082E
28
Additional Installation Tips
7.4
Ambient Temperature
The maximum ambient temperature for the operator panel is provided in the
specifications. The ambient temperature refers to the temperature in the device
cabinet which cools the operator panel’s electronics.
Top
50 °C inside
Operator
panel
Power
Power
30 °C outside
Middle
45 °C inside
Axial fan
120 x 120 mm
Airflow
Power
Bottom
40 °C inside
In most cases, the ambient temperature for the operator panel is significantly
higher than the device cabinet’s ambient temperature.
If the cabinet is tall and there are a number of heat-generating devices, the
temperature at the top of the cabinet will be considerably higher than the
theoretical temperature increase that would be expected. All electronics are
sensitive to heat. The lifespan of an electrolytic capacitor is cut in half with an
8-10 °C increase in temperature. A 15-20 °C temperature increase results in a
quarter of the lifespan etc.
Rittal has a good program for estimating the anticipated average temperature in
the cabinet as well as a large program for controlling the temperature in the device
cabinet.
An enamel-coated steel cabinet has a radiant heat value of 5.5 W/m2 and degrees
C.
Installing a fan inside the cabinet will even out the temperature, while moving air
provides considerably better cooling than still air.
Install the fan so that it sits in the cooler area and blows cold air against the operator
panel. If the fan is mounted at the top and sucks warm air upwards, the fan’s
ambient temperature will be higher, resulting in a shorter lifespan.
The operator panel’s loss effect = supply voltage x current. Virtually no power goes
to external users and no loss effects due to inputs.
Beijer Electronics, MAEN082E
29
Additional Installation Tips
7.5
Safety
Most of the operator panels are fed with 24 V DC.
Power supply
230 V AC to 24 V DC
Operator panel
+24 V
1
0V
4
Power supply
230 V AC to 24 V DC
Operator panel
+24 V
2
0V
4
Distance?
Power supply
230 V AC to 24 V DC
Operator panel
+24 V
3
0V
4
COM1
Small controller with expansion unit
Ch0
Ch1
230 V AC
COM100
Ch100
Ch101
5355
If a power supply that meets safety standards is used and only feeds the operator
panel, there is no problem. See 1 in drawing above.
However, if a 24 V unit that also feeds other units is used, there is reason to be
cautious, see 2 in drawing above. The operator panel does not have insulation
that meets safety requirements in the event of a potential short circuit between
230 V AC and 24 V DC. It is assumed that the 24 V feed is secure, for example,
SELV according to EN 60950 (protection against electric shock) and UL 950.
Example:
Here is an example that explains why a secure 24 V DC feed can be ruined by mixing
24 V relay contacts with 230 V AC relay contacts in a smaller controller. Check that the
clearances and creepage distances between 24 V DC and 230 V AC fulfill EN 60950 or
UL 950. If not, input a separate 24 V unit into the operator panel.
If there is a substantial distance between the relay contacts for 24 V DC and
230 V AC, it is OK to use the same 24 V devices for all feeds. See 3 in drawing
above.
Connect 0 V on the 24 V feed to the ground, see 4 in drawing above. This offers
three advantages:
•
Safety is increased. The 24 V feed will not be live in the event of a faulty
connection or short circuit between 0 V (24 V) and 230 V phase.
•
Transients on the 24 V feed are connected to the ground.
•
No risk that the 24 V feed is at a high level in relationship to the ground. This
is not unusual since there is high static electricity.
Beijer Electronics, MAEN082E
30
Additional Installation Tips
7.6
•
•
•
Cable and Bus Termination RS485
If maximum transfer distance and maximum transfer speed is needed,
shielded and twisted pair cable should be used. The mutual capacitance
may not exceed 52.5 pF/m, and the cable area should be at least 0.25 mm2
(AWG 24).
0 V, the reference voltage for communication should be included in
the cabling. With two-way communication use two pairs; one pair for
communication and one pair for 0 V.
The shield must be grounded at one end. The other end is usually grounded,
but with longer distances or when there is a difference in the ground potential,
the shield should be connected to the ground via 0.1 μF/250 V plastic
capacitor to prevent ground current in the braided shield. A number of
manufacturers recommend that the shield be grounded at each node. Various
manufacturers have different systems for bus termination.
Depending on the recipients’ design, the bus wires may be on the same level or
require pull-up or pull-down to ensure that no faulty signals are detected when the
bus is in resting mode (all transmitters are disconnected).
Beijer Electronics, MAEN082E
31
Additional Installation Tips
7.7
Boot Priority
The boot priority is the order in which the hardware storage devices are read.
Pressing F7 during boot will display a drop down menu with all available bootable
devices.
A change of the boot priority is only temporary. On next startup the boot priority
will be restored back to the factory setting.
7.8
Entering BIOS
Caution:
Unless you are an expert computer user, do not change the BIOS settings for this
program. Certain changes can cause your operator panel to work incorrectly.
Note:
Before using BIOS setup, it is recommended to write down the setup information for
future reference.
Note:
It is recommended to turn on and shut down the operator panel at least once before
installing any components/cards or before connecting the panel to external devices,
like for example serial devices.
1. Connect a USB Keyboard.
2. Connect power supply and turn on the operator panel.
3. While booting, press the F2 key immediately after the keyboard is initialized.
The initialization is indicated by the keyboard LED's.
If F2 is pressed before the keyboard is initialized, this keystroke will be lost.
If you waited too long and the operating system logo appears, continue to
wait until the operating system desktop is appearing. Then, shut down the
operator panel and try again.
Note:
The key used to enter the BIOS setup can differ depending on model and CPU Board.
The commonly used keys are ESC, DEL, F1 and F2. For more information, refer to the
BIOS manual.
The system setup allows to:
•
Change the system configuration (new installed hardware).
•
Setup boot devices and sequences.
•
Setup or change user options, for example passwords.
•
Read the installed memory and environmental parameters, for example CPU
heat.
For more information, refer to the BIOS manual.
Beijer Electronics, MAEN082E
32
Additional Installation Tips
7.9
Reset Switch
A reset switch is located under the fan lid.
Follow the instructions in chapter Replacing the Fan and Filter on how to remove
the fan lid to access the reset switch.
Beijer Electronics, MAEN082E
33
Head office
Beijer Electronics AB
Box 426
201 24 Malmö, Sweden
www.beijerelectronics.com / +46 40 358600

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project