AVGear AVG-PRO44-150 KIT User Manual

AVG-PRO44-150 KIT
18Gbps 4x4 HDBaseT
Matrix (150m)
All Rights Reserved
Version: AVG-PRO44-150 KIT_2024V1.0
AVG-PRO44-150 KIT
PLEASE READ THIS PRODUCT MANUAL CAREFULLY
BEFORE USING THIS PRODUCT.
This manual is only for operational instruction only, and not to be
used for maintenance. The functions described in this version are
current as at April 2024. Any changes of functions and operational parameters will be updated in future manual versions. Please
refer to your dealer for the latest product details.
Version 1.0 1/4/24
AVG-PRO44-150 KIT
SAFETY OPERATION GUIDE
To guarantee the reliable operation of the equipment and safety of
the user, please abide by the following procedures in installation,
use and maintenance:
1.
The system must be earthed properly. Please do not use two
blade plugs and ensure the alternating power supply ranges
from 100v to 240v and from 50Hz to 60Hz.
2.
Do not install the product in an environment where it will be
exposed to extreme hot or cold temperatures.
3.
This unit will generate heat during operation, please ensure
that you allow adequate ventilation to ensure reliable
operation.
4.
Please disconnect the unit from mains power if it will be left
unused for a long time.
5.
Please DO NOT try to open the casing of the equipment, DO
NOT attempt to repair the unit. Opening the unit will void the
warranty. There are high voltage components in the unit and
attempting to repair the unit could result in serious injury.
6.
Do not allow the unit to come into contact with any liquid as
that could result in personal injury and product failure.
AVG-PRO44-150 KIT
Table of Contents
1. Introduction. .................................................................................................................... 1
2. Features. .......................................................................................................................... 1
3. Package Contents. .......................................................................................................... 2
4. Specifications. ................................................................................................................. 2
5. Operation Controls and Functions. ............................................................................... 4
5.1. Matrix Panel............................................................................................................ 4
5.2. HDBaseT Receiver Panel. ...................................................................................... 6
6. IR Remote ........................................................................................................................ 7
7. IR Control System. .......................................................................................................... 8
8. IR Cable Pin Assignment. ............................................................................................... 10
9. EDID Management........................................................................................................... 10
10. Web GUI User Guide. .................................................................................................... 12
11. RS-232 Control Command. ........................................................................................... 19
12. Application Example. .................................................................................................... 25
AVG-PRO44-150 KIT
1. Introduction
The 18Gbps 4x4 HDBaseT(150M) Matrix can connect four HDMI sources to eight displays.
It features four HDMI outputs and each HDMI output is mirrored to provide a CAT-Cable
output which runs simultaneously. HDBaseT output can extend video transmission distance
up to 492ft / 150m via a single Cat 5e/6/7 cable and the resolution is up to 4K2K@60Hz 4:4:4.
Audio de-embedded to analog and coaxial audio is supported. Each HDMI output supports
4K2K to 1080P downscaler independently.
The product supports IR matrix. The IR signal is one-to-one control at the Matrix end, but the
IR signal follows HDMI video channel at the HDBaseT Receiver end.
The product provides an intuitive set of front panel with OLED screen and supports control via
front panel buttons, IR remote, RS-232, LAN, and Web GUI.
2. Features
☆ HDMI 2.0b, HDCP 2.2 and HDCP 1.x compliant
☆ Video resolution up to 4K2K@60Hz (YUV 4:4:4) on all HDMI & HDBaseT ports
☆ 4 HDMI inputs, 4 HDMI & HDBaseT mirrored outputs
☆ HDMI ports transmit 18Gbps lossless uncompressed video bandwidth
☆ Support 18Gbps lossless compressed HDBaseT signal transmission
☆ Support 4K->1080P Down Scaler for each output port
☆ HDR, HDR10, HDR10+, Dolby Vision, HLG are supported
☆ HDBaseT output can extend video transmission distance up to 492ft / 150m for 1080P
or 394ft / 120m for 4K2K via a single Cat 5e/6/7 cable
☆ HDMI audio pass-through up to 7.1CH HD audio (LPCM, Dolby TrueHD and DTS-HD
Master Audio)
☆ Support IR matrix
☆ Audio de-embedded is supported via analog and coax ports
☆ Advanced EDID management and CEC control are supported
☆ 24V POC on all HDBaseT ports
☆ 1U rack mounted design with front panel OLED display
☆ Control via front panel buttons, IR remote, RS-232, LAN and Web GUI
- 1 / 25 -
AVG-PRO44-150 KIT
3. Package Contents
①
②
③
④
⑤
⑥
⑦
⑧
⑨
1 × 18Gbps 4x4 HDBaseT(150M) Matrix
4 × HDBaseT Receiver
1 × Matrix IR Remote
1 × 100~240V AC 50/60Hz Power cable
1 × RS-232 serial cable (1.5 meters, male to female head)
4 × 3-pin Phoenix Connector & 4 x 5-pin Phoenix Connector
5 × IR Blaster cable (1.5 meters)
5 × IR Receiver cable (1.5 meters)
10 × Mounting Ear (Matrix and Receiver)
⑩ 1 × User Manual
4. Specifications
Technical
HDMI Compliance
HDMI 2.0b
HDCP Compliance
HDCP 2.2 and HDCP 1.x
Video Bandwidth
18Gbps
Video Resolution
Up to 4K2K@50/60Hz (4:4:4)
Color Space
RGB 4:4:4, YCbCr 4:4:4/4:2:2/4:2:0
Color Depth
8-bit, 10-bit, 12-bit (1080p@60Hz)
8-bit (4K2K@60Hz YUV4:4:4)
8-bit, 10-bit, 12-bit (4K2K@60Hz YCbCr 4:2:2/4:2:0）
HDR
HDR10, HDR10+, Dolby Vision, HLG
HDMI Audio Formats
LPCM 2.0/2.1/5.1/6.1/7.1, Dolby Digital, Dolby TrueHD, Dolby Digital
Plus (DD+), DTS-ES, DTS HD Master, DTS HD-HRA, DTS-X
Coax Audio Formats
PCM 2.0, Dolby Digital / Plus, DTS 2.0/5.1
Analog Balanced
Audio Formats
PCM 2.0CH
Vmax
2Vrms
SNR
＞90dB
THD+N Ratio
＜0.1%（V_max） 0.001%~0.01%（V_best）
Crosstalk
＞80dB
Frequency Response
20Hz~20kHz ±0.5dB
ESD Protection
IEC 61000-4-2: ±8kV (Air-gap discharge), ±4kV (Contact discharge)
- 2 / 25 -
AVG-PRO44-150 KIT
Connection
Matrix
HDBaseT Receiver
Inputs: 4 × HDMI Type A [19-pin female]
Outputs: 4 × HDMI Type A [19-pin female]
4 × HDBaseT port [RJ45]
4 × Coaxial audio [3.5mm Stereo Mini-jack]
4 × balanced analog audio [5-pin Phoenix
connector]
Controls: 5 × IR IN [3.5mm Stereo Mini-jack]
5 × IR OUT [3.5mm Stereo Mini-jack]
1 × TCP/IP [RJ45]
1 × RS-232 [D-Sub 9]
Input:
1 × HDBT IN [RJ45, 8-pin female]
Outputs: 1 × HDMI Type A [19-pin female]
1 × AUDIO OUT [3.5mm Stereo Mini-jack]
Controls: 1 × IR IN [3.5mm Stereo Mini-jack]
1 × IR OUT [3.5mm Stereo Mini-jack]
1 × RS-232 [3-pin Phoenix connector]
1 × SERVICE [Mini-USB, Update port]
Mechanical
Housing
Metal Enclosure
Color
Black
Dimensions
Matrix: 440mm (W) × 200mm (D) × 44.5mm (H)
Receiver: 140mm (W) × 65mm (W) × 18mm (W)
Weight
Matrix: 3.1Kg, Receiver: 155g
Power Supply
AC 100 - 240V 50/60Hz
Power Consumption
60W (Max)
Operating Temperature
0°C ~ 40°C / 32°F ~ 104°F
Storage Temperature
-20°C ~ 60°C / -4°F ~ 140°F
Relative Humidity
20~90% RH (non-condensing)
Resolution / Distance
4K60 - Feet / Meters
CAT5e/6/7
Resolution / Cable length
HDMI IN / OUT
492ft / 150m
4K60 Feet / Meters
4K30 Feet / Meters
1080P60 Feet / Meters
16ft / 5m
32ft / 10m
50ft / 15m
The use of “Premium High Speed HDMI” cable is highly recommended.
- 3 / 25 -
AVG-PRO44-150 KIT
5. Operation Controls and Functions
5.1 Matrix Panel
Front Panel
1
2
3
5
4
1
2
3
4
MENU
UP
POWER
1
2
3
4
ENTER
DOWN
LOCK
OUTPUT
INPUT
6
NO.
Name
7
Function Description
1
OLED screen
Display matrix switching status, input / output port, EDID, Baud rate,
IP Address.
2
Power LED
The LED will illuminate in green when the product is working normally, and
red when the product is on standby.
3
OUTPUT /
INPUT buttons
You need to press an output button (1~4) firstly and then press an input
button (1~4) to select the corresponding input source for the output port.
4
①EDID setting: On the initial OLED display screen, press “MENU” button
to enter “Select EDID” interface, press “UP/DOWN” button to select the
required EDID, and press the “ENTER” button to enter “Copy to Input:”
interface. Then press “UP/DOWN” button to select the input port you
need to set, and press “ENTER” button again to confirm.
②Baud rate setting: On the initial OLED display screen, press “MENU”
button twice to enter “SELECT BAUD” interface, and press “UP/DOWN”
MENU / ENTER button to select the required Baud rate, finally press the “ENTER” button
/ UP /DOWN
to confirm the setting.
③IP Address Check: On the initial OLED display screen, press “MENU”
button three times to enter the IP interface and check the current IP
address, then press “UP/DOWN” button to switch DHCP ON/OFF, finally
press the “ENTER” button to confirm the setting.
Pressing the “MENU” button again will return to the initial OLED display
status.
5
POWER button
Press and hold the POWER button for 3 seconds to enter the standby
mode, then press the button again to wake up the device.
6
IR Window
IR receiver window, it only receives the IR remote signal from this product.
7
LOCK button
Press the LOCK button to lock front panel buttons (Except the power
button); Press the button again to unlock.
- 4 / 25 -
AVG-PRO44-150 KIT
Rear Panel
2
1
3
4
5
AUDIO OUT
IR IN
1
2
OUTPUT 1
HDMI
3
4
ALL
1
2
3
4
ALL IR OUT
COAX 1
OUTPUT 2
HDBT
HDMI
HDBT
COAX 2
R+
1
2
INPUT
3
4
7
Name
HDMI
L+
R+
COAX 3
L+
HDBT
HDMI
COAX 4
R+
OUTPUT 4
OUTPUT 3
6
No.
L+
L+
TCP/IP
HDBT
R+
RS-232
CONTROL
100-240V AC 50/60HZ
8
6
Function Description
1
IR IN (1/2/3/4/
ALL) ports
Connect to IR receiver cable, the IR receive signal will emit to the “IR
OUT” port of the HDBaseT Receiver.
2
IR OUT (1/2/3/4/
ALL) ports
Connect to IR blaster cable, the IR emit signal is from the “IR IN” port of
the HDBaseT Receiver.
3
AUDIO OUT
(1-4) ports
4 groups of coaxial and balanced analog audio mirrored output ports.
AUDIO OUT (1-4) follows the video output of OUTPUT (1-4) ports.
4
GND
Connect the housing to the ground.
5
POWER input
Power port: Connect to 100~240V AC 50/60Hz power cable.
Power switch: Press the switch to turn on/off the power.
6
OUTPUT (1-4)
ports
HDMI output ports, connect to HDMI display device such as TV or
monitor with an HDMI cable.
HDBT mirrored output ports, connect to HDBaseT Receiver via CAT
cable.
7
INPUT (1-4)
ports
HDMI input ports, connect to HDMI source device such as DVD or PS4
with an HDMI cable.
CONTROL ports
TCP/IP: The link port for TCP/IP control. Connect to an active Ethernet
link with an RJ45 cable.
RS-232: Command control port. Connect to a PC or control system
with a D-Sub 9-pin cable to control the Matrix.
8
↑
↑
Connection Signal
Indicator Lamp
Data Signal
Indicator Lamp
▪ Illuminating: HDMI signal with HDCP.
▪ Flashing: HDMI signal without HDCP.
▪ Dark: No HDMI signal.
Video (OUT)
- 5 / 25 -
▪ Illuminating: Matrix and HDBaseT
Receiver are in good connection status.
▪ Flashing: Matrix and HDBaseT
Receiver are in poor connection status.
▪ Dark: Matrix and HDBaseT
Receiver are not connected.
AVG-PRO44-150 KIT
5.2 HDBaseT Receiver Panel
SERVICE
2
DC 24V
HDBT IN
1
3
5 4 6
HDMI OUT
AUDIO OUT
IR IN
IR OUT
7
8
9
10
No.
Name
1
Power LED
2
SERVICE port Firmware update port.
11
Function Description
Red LED will be on when the receiver is powered on.
3
DC 24V
DC 24V/1A power supply input port.
Note: The Matrix supports POC function, it means that either
transmitter or receiver is powered on by 24V/1A power adapter,
the other one doesn’t need power supply.
4
HDBT IN
RJ45 connector for connecting the HDBT OUTPUT port of
Matrix with a CAT cable.
5
▪ Illuminating: Matrix and Receiver are in good connection status.
Connection
Signal
▪ Flashing: Matrix and Receiver are in poor connection status.
Indicator lamp ▪ Dark: Matrix and Receiver are not connected.
6
Data Signal
Indicator
▪ Illuminating: HDMI signal with HDCP.
▪ Flashing: HDMI signal without HDCP.
▪ Dark: No HDMI signal.
7
HDMI OUT
HDMI output port, connect to HDMI display device such as TV or
monitor with HDMI cable.
8
AUDIO OUT
9
IR IN
Analog audio output port. The audio is extracted from HDMI signal.
Connect to IR receiver cable, the IR receive signal will emit to the
“IR OUT” port of the Matrix.
10 IR OUT
Connect to IR blaster cable, the IR emit signal is from the “IR IN”
port of the Matrix.
11 RS-232
Connect to a PC or control system with a 3-pin phoenix connector
cable to transmit command between the Matrix and HDBaseT
Receiver.
- 6 / 25 -
AVG-PRO44-150 KIT
6. IR Remote
1
① Power on or Standby: Power on the Matrix or set
it to standby mode.
2
3
4
5
② Output 1: Press 1\2\3\4 button to select input source to
HDMI OUTPUT 1.
③ Output 2: Press 1\2\3\4 button to select input source to
HDMI OUTPUT 2.
④ Output 3: Press 1\2\3\4 button to select input source to
HDMI OUTPUT 3.
⑤ Output 4: Press 1\2\3\4 button to select input source to
HDMI OUTPUT 4.
: Select the last or next input source button.
- 7 / 25 -
AVG-PRO44-150 KIT
7. IR Control System
The product is not only a matrix switch but also an extender. It supports bi-directional IR
control. When Matrix is connected to HDBaseT Receiver through Cat 5e/6/7 cable, you can
control remote display device (HDBaseT) or input source device (Matrix) through IR signal
transmission. But you must note that the IR signal transmission method is different from the
method from Matrix (local) to HDBaseT Receiver (remote) and from HDBaseT Receiver
(remote) to Matrix (local).
TV 1 remote
TV 3 remote
At the Matrix end (Local end): the IR signal is one-to-one transmission. For example, the
IR IN 1 port signal of the Matrix will emit to IR OUT port of the HDBaseT Receiver 1, and the
IR IN 3 port signal of the Matrix will emit to IR OUT port of the HDBaseT Receiver 3. It doesn’t
follow the video switch to change. IR IN ALL port signal of the Matrix will emit to all IR OUT ports
of HDBaseT receivers simultaneously. Please see the following connection diagram.
AUDIO OUT
IR IN
Matrix
1
2
OUTP UT 1
3
4
ALL
1
1
HDMI
HDBT
2
3
4
ALL I R OUT
COAX 1
OUTP UT 2
HDMI
3
2
HDBT
L+
R+
OUTP UT 3
COAX 2
L+
R+
OUTP UT 4
COAX 3
L+
R+
COAX 4
L+
TCP/IP
R+
RS -232
4
100-240V AC 50/60HZ
I NP UT
HDMI
HDBT
HDMI
HDBT
CONTROL
CAT 5e/6/7 cable
DC 24V
HDBT IN
CAT 5e/6/7 cable
HDMI OUT
AUDIO OUT
IR IN
IR OUT
HDBT IN
DC 24V
Receiver 3
HDMI OUT
AUDIO OUT
IR IN
IR OUT
Receiver 1
IR Blaster
TV 3
IR Blaster
TV 1
Figure 1: IR connection diagram (Matrix end)
- 8 / 25 -
AVG-PRO44-150 KIT
At HDBaseT receiver (Remote end): IR signal follows video switch to change. For example,
the HDMI output signal on the HDBaseT Receiver 1 is from the HDMI INPUT 2 port, so IR
input signal of the HDBaseT Receiver 1 will emit to IR OUT 2 port of the Matrix. The HDMI
output signal on the HDBaseT Receiver 3 is from the HDMI INPUT 4 port. Then, IR input
signal of the HDBaseT Receiver 3 will emit to IR OUT 4 port of the Matrix etc. Any of
HDBaseT Receiver’s IR IN signal can output from IR OUT ALL port of the Matrix and the
IR OUT ALL signal of the Matrix depends on your IR remote of source device. Please see
the following connection diagram.
AUDIO OUT
IR IN
1
2
OUTP UT 1
HDMI
HDBT
3
4
ALL
1
2
4
3
ALL IR OUT
COAX 1
OUTP UT 2
HDMI
L+
R+
COAX 2
OUTP UT 3
1
HDBT
2
3
4
INPUT
HDMI
L+
R+
COAX 3
OUTP UT 4
HDBT
HDMI
L+
R+
COAX 4
TCP/IP
HDBT
L+
R+
Matrix
RS -232
100-240V AC 50/60HZ
CONTROL
CAT 5e/6/7 cable
Blu-ray player
HDBT IN
DC 24V
DVD
HDMI OUT
AUDIO OUT
IR IN
HDBT IN
DC 24V
CAT 5e/6/7 cable
HDMI OUT
AUDIO OUT
IR IN
IR OUT
Receiver 3
IR OUT
Receiver 1
TV 3
TV 1
DVD remote
Figure 2: IR connection diagram (HDBaseT Receiver end)
- 9 / 25 -
Blu-ray player remote
AVG-PRO44-150 KIT
8. IR Cable Pin Assignment
IR BLASTER
IR RECEIVER
9. EDID Management
This Matrix has 21 factory defined EDID settings, 2 user-defined EDID modes and 8 copy EDID
modes. You can select defined EDID mode or copy EDID mode to input port through on-panel
button, RS-232 control or Web GUI.
On-panel button operation: On the initial OLED display screen, press “MENU” button to enter
the EDID setting interface, press “UP/DOWN” button to select the required EDID, and press
the “ENTER” button to enter “Copy to Input:” interface. Then press “UP/DOWN” button to select
the input port you need to set, and press “ENTER” button again to confirm this operation.
RS-232 control operation: Connect the Matrix to PC with a serial cable, then open a Serial
Command tool on PC to send ASCII command “s edid in x from z!” to set EDID. For details,
please refer to “EDID Setting” in the ASCII command list of “11. RS-232 Control Command”.
Web GUI Operation: Please check the EDID management in the “Input page” of “10. Web
GUI User Guide”.
- 8 / 25 -
AVG-PRO44-150 KIT
The defined EDID setting list of the product is shown as below:
EDID Mode
EDID Description
1
1080p, Stereo Audio 2.0
2
1080p, Dolby/DTS 5.1
3
1080p, HD Audio 7.1
4
1080i, Stereo Audio 2.0
5
1080i, Dolby/DTS 5.1
6
1080i, HD Audio 7.1
7
3D, Stereo Audio 2.0
8
3D, Dolby/DTS 5.1
9
3D, HD Audio 7.1
10
4K2K30_444, Stereo Audio 2.0
11
4K2K30_444, Dolby/DTS 5.1
12
4K2K30_444, HD Audio 7.1
13
4K2K60_420, Stereo Audio 2.0
14
4K2K60_420, Dolby/DTS 5.1
15
4K2K60_420, HD Audio 7.1
16
4K2K60_444, Stereo Audio 2.0
17
4K2K60_444, Dolby/DTS 5.1
18
4K2K60_444, HD Audio 7.1
19
4K2K60, Stereo Audio 2.0 HDR
20
4K2K60, Dolby/DTS 5.1 HDR
21
4K2K60, HD Audio 7.1HDR
22
User define1
23
User define2
24~27
Copy from HDMI OUTPUT 1~4
28~31
Copy from HDBT OUTPUT 1~4
- 11 / 25 -
AVG-PRO44-150 KIT
10. Web GUI User Guide
The Matrix can be controlled by Web GUI. The operation method is shown as below:
Step 1: Get the current IP Address.
The default IP address is 192.168.1.100. You can get the current Matrix IP address in two ways:
The first way: You can get the IP address via panel buttons. On the initial OLED display, press
“MENU” button three times to enter the IP interface and check the current IP address.
The second way: You can get the IP address via RS-232 control. Send the ASCII command
“ r ipconfig!” through a Serial Command tool, then you’ll get the feedback information as shown
below:
IP:192.168.61.103 in the above figure is the current Matrix IP address (this IP address is
variable, depending on what the specific machine returns).
For the details of RS-232 control, please refer to “11. RS-232 Control Command”.
Step 2: Connect the TCP/IP port of the Matrix to a PC with an UTP cable (as shown in the
following figure), and set the IP address of the PC to be in the same network segment with
the Matrix.
PC
Step 3: Input the current IP address of Matrix into your browser on the PC to enter Web GUI
page.
- 12/ 25 -
AVG-PRO44-150 KIT
After entering the Web GUI page, there will be a Login page, as shown below:
Select the Username from the list and enter the password. The default passwords are:
Username
Password
User
user
Admin
admin
After entering the password, click the “LOGIN” button and the following Status page will
appear.
■ Status Page
The Status page provides basic information about the product model, installed firmware
version and the network settings of the device.
- 13 / 25 -
AVG-PRO44-150 KIT
■ Video Page
You can do the following operations on the Video page:
① Output: The current device’s OUTPUT port. You can select signal source for it.
② Input: You can click the drop-down menu to select signal source for the corresponding
OUTPUT port .
③ Presets Name: You can name the current scene with maximum length of 12 characters
(Chinese name is unsupported).
④ Presets Set: You can restore the settings of the last saved audio-video matrix switching
relationship.
⑤ Presets Save: You can save audio-video matrix switching relationship.
⑥ Presets Clear: You can clear the saved audio-video matrix switching relationship.
■ Input Page
You can do the following operations on the Input page:
① Inputs: Input channel of the device.
② Active: It indicates whether the channel is connected to a signal source.
③ Name: The input channel’s name. You can modify it by entering the corresponding name
(max length: 12 characters) in the input box (Chinese name is unsupported).
④ EDID: You can set the current channel’s EDID. The specific operation is as follows:
- 14 / 25 -
AVG-PRO44-150 KIT
Set EDID for the User
Click the “Browse” button, then select the bin file. If you select the wrong EDID file, there will
be a prompt, as shown in the following figure:
Make sure to select the correct file, then you can check the name of the selected file. Select
“User 1” or “User 2”, then click “Upload”. After successful setting, it will prompt as follows:
Download the EDID File for the Corresponding Input Channel
Click the drop-down box of “Select EDID File” to select the corresponding input channel. Then
click “Download” to download the corresponding EDID file.
■ Output Page
You can do the following operations on the Output page:
① Outputs: Output channel of the device.
② Name: The current output channel’s name. You can modify it by entering the corresponding
name (max length: 12 characters) in the input box (Chinese name is unsupported).
③ Type: The current output channel’s type (HDMI or HDBT).
④ Cable: It indicates the connection status of output ports. When the output port is connected
to the display, it shows green, otherwise, it shows gray.
⑤ Scaler Mode: Set the current output resolution mode.
⑥ Stream: Turn on/off the output stream.
- 15 / 25 -
AVG-PRO44-150 KIT
■ CEC Page
You can perform CEC management on this page:
① Input Control: You can control the operation of each input source by pressing the icons
on the page. (You can control multiple inputs simultaneously.)
② Output Control: You can control the operation of each display, such as power on/off,
volume +/-, active source switching. (You can control multiple outputs simultaneously.)
■ Network Page
Set the Default Network
Click “Set Network Defaults” button, there will be a prompt, as shown in the following figure:
- 16 / 25 -
AVG-PRO44-150 KIT
Click “OK” to search the IP Address again, as shown in the following figure:
After searching is completed, it will switch to the login page, the default network setting is
completed.
Modify User Password
Click the “User” button, enter the correct Old Password, New Password, and Confirm
Password, then click “Save”. After successful modification, there will be a prompt, as shown
in the following figure:
Note: Input rules for changing passwords:
(1) The password can’t be empty.
(2) New Password can’t be the same as Old Password.
(3) New Password and Confirm Password must be the same.
- 17 / 25 -
AVG-PRO44-150 KIT
Modify Network Setting
Modify the Mode/IP Address/Gateway/Subnet Mask/Telnet Port as required, click “Save”
to save the settings, then it will come into effect.
After modification, if the Mode is “Static”, it will switch to the corresponding IP Address;
if the Mode is “DHCP”, it will automatically search and switch to the IP Address assigned
by the router.
■ System Page
① Panel Lock: Click to lock/unlock panel buttons. “On” indicates that panel buttons are
unavailable; “Off” indicates panel buttons are available.
② Beep: Click to turn on/off the beep.
③ LCD: You can turn on/off the LCD, and set the turn-on time (15s/30s/60s).
④ Serial Baud Rate: Click the value to set the Serial Baud Rate.
⑤ Firmware Update: Click “Browse” to select the update file, then click “Update” to
complete firmware update.
⑥ Factory Reset: You can reset the machine to factory defaults by clicking “Reset”.
⑦ Reboot: You can reboot the machine by clicking “Reboot”.
Note: After reset/reboot, it will switch to the login page.
- 18 / 25 -
AVG-PRO44-150 KIT
11. RS-232 Control Command
The product also supports RS-232 control. You need a serial cable with RS-232 male head and
DB9 transfer USB male head. The RS-232 head of the serial cable is connected to the RS-232
control port with DB 9 at the rear of the Matrix, and the USB head of the serial cable is connected
to a PC. The connection method is as follows:
RS232
Then, open a Serial Command tool on PC to send ASCII command to control the Matrix.
The ASCII command list about the product is shown as below.
ASCII Command
Serial port protocol. Baud rate: 115200,
Data bits: 8bit, Stop bits:1, Check bit: 0
x - Parameter 1; y - Parameter 2; ! - Delimiter
Command Code
Function Description
Example
Feedback
Default Setting
Power
Power on
s power z!
Power on/off the device,z=0~1
(z=0 power off, z=1 power on)
s power 1!
r power!
Get current power state
r power!
System Initializing...
Initialization Finished!
FW version x.xx.xx
power on/power off
Reboot...
Reboot the device
s reboot!
help!
List all commands
help!
r type!
Get device model
r type!
HDP-MXB44H150
r status!
Get the unit all status:
power, beep, lock, in/out
connection, video/audio
crosspoint, edid, scaler,hdcp,
network status
r fw version!
MCU BOOT: Vx.xx.xx
MCU APP: Vx.xx.xx
SUB1 APP: Vx.xx.xx
SUB2 APP: Vx.xx.xx
CPLD APP: Vx.xx.xx
WEB GUI: Vx.xx
s reboot!
System Initializing...
Initialization Finished!
FW version x.xx.xx
System Setup
r status!
r fw version!
Get device current status
Get Firmware version
- 19 / 25 -
power on
AVG-PRO44-150 KIT
Command Code
Function Description
Example
Feedback
r link in x!
Get the connection status of the
x input port，x=0~4(0=all)
r link in 1!
hdmi input 1: connect
r link out y!
Get the connection status of the
y output port，y=0~4(0=all)
r link out 1!
hdmi output 1: connect
hdbt output 1: connect
s reset!
Reset to factory defaults
s beep z!
Enable/Disable buzzer function,
z=0~1(z=0 beep off, z=1 beep on) s beep 1!
r beep!
Get buzzer state
s lock z!
r lock!
s lcd on time z!
r lcd mode!
s save preset z!
s recall preset z!
s clear preset z!
r preset z!
s logo1
****************!
s baud rate xxx!
r baud rate!
s reset!
r beep!
Reset to factory defaults
System Initializing...
Initialization Finished!
FW version x.xx.xx
beep on
beep off
beep on
beep on / beep off
panel button
lock off
s lock 1!
Get panel button lock state
r lock!
Set LCD screen remain on time,
z=0~4 (0:off, 1:always on, 2:15s, s lcd on time 1!
3:30s, 4:60s)
Get the backlight status of lcd
r lcd mode!
screen
Save switch state between all
output port and the input port to s save preset 1!
preset z, z=1~4
panel button lock on/off
Call saved preset z scenarios,
z=1~4
Clear stored preset z scenarios,
z=1~4
s recall preset 1!
recall from preset 1
s clear preset 1!
clear preset 1
Get preset z information, z=1~4 r preset 1!
Set the logo name displayed on
s logo1 Matrix
the first line of LCD screen, the
Swtich!
max character is 16
Set the serial port baud rate of
s baud rate
RS02 module, z=(115200,57600,
115200!
38400,19200,9600,4800)
Get the serial port baud rate of
r baud rate!
RS02 module
Default Setting
lcd always on
lcd on
30 seconds
lcd always on
save to preset 1
video/audio crosspoint
logo1:Matrix Swtich
Baudrate:115200
115200
Baudrate:115200
Set the control ID of the product,
z=000~999
s id 888!
id 888
0
s in x av out y!
Set input x to output y，
x=1~4，y=0~4(0=all)
s in 1 av out 2!
input 1 -> output 2
ptp
r av out y!
Get output y signal status
y=0~4(0=all)
r av out 0!
input 1 -> output 1
input 2 -> output 2
input 3 -> output 3
input 4 -> output 4
s hdmi y stream z!
Set hdmi output y stream on/off,
y=0~4(0=all)
z=0~1(0:disable,1:enable)
r hdmi y stream!
Get hdmi output y stream status,
r hdmi 1 stream!
y=0~4(0=all)
s id z!
Output Setting
enable hdmi output 1 stream
s hdmi 1 stream 1! disable hdmi output 1 stream
enable hdmi all outputs stream enable
s hdmi 0 stream 1! disable hdmi all outputs stream
- 20 / 25 -
enable hdmi output 1 stream
AVG-PRO44-150 KIT
Command Code
Function Description
Set hdbt output y stream on/off,
s hdbt y stream z! y=0~4(0=all)
z=0~1(0:disable, 1:enable)
r hdbt y stream!
Get hdbt output y stream status,
y=0~4(0=all)
Set hdmi output y port output
s hdmi y scaler z! scaler mode，y=0~4(0=all), z=1~3
(1=bypass, 2=4k->1080p, 3=Auto)
r hdmi y scaler!
Get hdmi output y port output
mode y=0~4(0=all)
Set hdbt output y port output
s hdbt y scaler z! scaler mode，y=0~4(0=all), z=1~3
(1=bypass, 2=4k->1080p, 3=Auto)
r hdbt y scaler !
Get hdbt output y port output
mode y=0~4(0=all)
Example
Feedback
Default Setting
enable hdbt output 1 stream
s hdbt 1 stream 1! disable hdbt output 1 stream
s hdbt 0 stream 1! enable hdbt all outputs stream enable
disable hdbt all outputs stream
r hdbt 1 stream!
enable hdbt output 1 stream
hdmi output 1 set to
s hdmi 1 scaler 1! bypass mode
s hdmi 0 scaler 1! hdmi all outputs set to
bypass mode
r hdmi 1 scaler!
hdmi output 1 set to
bypass mode
hdbt output 1 set to
s hdbt 1 scaler 1! bypass mode
s hdbt 0 scaler 1! hdbt all outputs set to
bypass mode
r hdbt 1 scaler !
hdmi all outputs
set to bypass
mode
hdbt all outputs
set to bypass
mode
hdbt output 1 set to
bypass mode
EDID Setting
Set input x EDID from default
EDID z, x=0~4(0=all), z=1~31
1, 1080p, Stereo Audio 2.0
2, 1080p, Dolby/DTS 5.1
3, 1080p, HD Audio 7.1
4, 1080i, Stereo Audio 2.0
5, 1080i, Dolby/DTS 5.1
6, 1080i, HD Audio 7.1
7, 3D, Stereo Audio 2.0
8, 3D, Dolby/DTS 5.1
9, 3D, HD Audio 7.1
10, 4K2K30_444, Stereo Audio 2.0
s edid in 1 from 1!
11, 4K2K30_444, Dolby/DTS 5.1
s edid in x from z! 12, 4K2K30_444, HD Audio 7.1
13, 4K2K60_420, Stereo Audio 2.0
14, 4K2K60_420, Dolby/DTS 5.1
s edid in 0 from 1!
15, 4K2K60_420, HD Audio 7.1
16, 4K2K60_444, Stereo Audio 2.0
17, 4K2K60_444, Dolby/DTS 5.1
18, 4K2K60_444, HD Audio 7.1
19, 4K2K60_444, Stereo Audio 2.0 HDR
20, 4K2K60_444, Dolby/DTS 5.1 HDR
21, 4K2K60_444, HD Audio 7.1 HDR
22, User define1
23, User define2
24~27, copy from hdmi output 1~4
28~31, copy from hdbt output 1~4
r edid in x!
Get EDID status of the input x，
x=0~4(0=all input)
r edid in 0!
- 21 / 25 -
input 1 EDID:1080p,
Stereo Audio 2.0
all inputs EDID:1080p,
Stereo Audio 2.0
input1 EDID: 4K2K60_
444,Stereo Audio 2.0
input2 EDID: 4K2K60_
444,Stereo Audio 2.0
input3 EDID: 4K2K60_
444,Stereo Audio 2.0
input4 EDID: 4K2K60_
444,Stereo Audio 2.0
1080p,
Stereo Audio 2.0
AVG-PRO44-150 KIT
Command Code
Function Description
Example
Get the EDID data of the hdmi
r edid data hdmi y!
output y port，y=1~4
r edid data hdbt y!
Feedback
r edid data hdmi 1! EDID: 00 FF FF FF FF
FF FF 00 ………
Get the EDID data of the hdbt
output y port，y=1~4
r edid data hdbt 1!
EDID: 00 FF FF FF FF
FF FF 00 ………
s cec in 1 on!
input 1 power on
s cec in 1 off!
input 1 power off
s cec in 1 menu!
input 1 open menu
CEC Setting
s cec in x on!
s cec in x off!
s cec in x menu!
s cec in x play!
s cec in x pause!
s cec in x stop!
s cec in x rew!
set input x power on by CEC,
x=0~4(0=all input)
set input x power off by CEC,
x=0~4(0=all input)
set input x open menu by CEC,
x=0~4(0=all input)
set input x play by CEC,
x=0~4(0=all input)
set input x pause by CEC,
x=0~4(0=all input)
set input x stop by CEC,
x=0~4(0=all input)
set input x rewind by CEC,
x=0~4(0=all input)
s cec in 1 play!
input 1 play operation
s cec in 1 pause!
iInput 1 pause
operation
s cec in 1 stop!
input 1 stop operation
s cec in 1 rew!
input 1 rewind
operation
s cec in x mute!
set input x volume mute by CEC,
x=0~4(0=all input)
s cec in 1 mute!
input 1 volume mute
s cec in x vol-!
set input x volume down by CEC,
s cec in 1 vol-!
x=0~4(0=all input)
input 1 volume down
s cec in x vol+!
set input x volume up by CEC,
x=0~4(0=all input)
s cec in 1 vol+!
input 1 volume up
s cec in x ff!
set input x fast forward by CEC,
x=0~4(0=all input)
s cec in 1 ff!
input 1 fast forward
operation
s cec in x previous!
set input x previous by CEC,
x=0~4(0=all input)
s cec in 1 previous!
input 1 previous
operation
s cec in x next!
set input x next by CEC,
x=0~4(0=all input)
s cec in 1 next!
input 1 next operation
s cec hdmi out y
on!
set hdmi output y power on by
CEC, y=0~4(0=all hdmi output)
s cec hdmi out 1
on!
hdmi output 1 power
on
s cec hdbt out y on!
set hdbt output y power on by
CEC, y=0~4(0=all hdbt output)
s cec hdbt out 1 on! hdbt output 1 power on
s cec hdmi out y
off!
set hdmi output y power off by
CEC, y=0~4(0=all hdmi output)
s cec hdmi out 1
off!
s cec hdbt out y off! set hdbt output y power off by
CEC, y=0~4(0=all hdbt output)
hdmi output 1 power
off
s cec hdbt out 1 off! hdbt output 1 power off
s cec hdmi out y
mute!
set hdmi output y volume mute by s cec hdmi out 1
CEC, y=0~4(0=all hdmi output)
mute!
hdmi output 1 volume
mute
s cec hdbt out y
mute!
s cec hdmi out y
vol-!
set hdbt output y volume mute by s cec hdbt out 1
CEC, y=0~4(0=all hdbt output)
mute!
set hdmi output y volume down s cec hdmi out 1
by CEC, y=0~4(0=all hdmi output) vol-!
hdbt output 1 volume
mute
s cec hdbt out y
vol-!
s cec hdmi out y
vol+!
set hdbt output y volume down by s cec hdbt out 1
CEC, y=0~4(0=all hdbt output)
vol-!
hdmi output 1 volume
down
hdbt output 1 volume
down
set hdmi output y volume up by
CEC, y=0~4(0=all hdmi output)
s cec hdmi out 1
vol+!
hdmi output 1 volume
up
s cec hdbt out y
vol+!
set hdbt output y volume up by
CEC, y=0~4(0=all hdbt output)
s cec hdbt out 1
vol+!
hdbt output 1 volume
up
s cec hdmi out y
active!
set hdmi output y active source s cec hdmi out 1
by CEC, y=0~4(0=all hdmi output) active!
hdmi output 1 active
source
s cec hdbt out y
active!
set hdbt output y active source s cec hdbt out 1
by CEC, y=0~4(0=all hdbt output) active!
hdbt output 1 active
source
- 22 / 25 -
Default Setting
AVG-PRO44-150 KIT
Command Code
Function Description
Example
Feedback
Network Setting
r ipconfig!
Get the Current IP Configuration
r ipconfig!
IP Mode: Static
IP: 192.168.1.72
Subnet Mask:
255.255.255.0
Gateway: 192.168.1.1
TCP/IP port=8000
Telnet port=10
Mac address:
00:1C:91:03:80:01
r mac addr!
Get network MAC address
r mac addr!
Mac address:
00:1C:91:03:80:01
s ip mode z!
Set network IP mode to static IP
or DHCP,
z=0~1 (z=0 Static, z=1 DHCP )
s ip mode 0!
Set IP mode:Static
(Please use "s net reboot!"
command or repower device
to apply new config!)
r ip mode!
Get network IP mode
r ip mode!
IP Mode: Static
Set IP address:
192.168.1.100
(Please use "s net reboot!"
command or repower
device to apply new config!)
DHCP on, Device can't
config static address,
set DHCP off first.
s ip addr
xxx.xxx.xxx.xxx!
Set network IP address
s ip addr
192.168.1.100!
r ip addr!
Get network IP address
r ip addr!
IP:192.168.1.100
s subnet
xxx.xxx.xxx.xxx!
Set network subnet mask
s subnet
255.255.255.0!
Set subnet Mask
address:255.255.255.0
(Please use "s net reboot!"
command or repower device
to apply new config!)
DHCP on, Device can't
config subnet mask,
set DHCP off first.
r subnet!
Get network subnet mask
r subnet!
Subnet Mask:
255.255.255.0
s gateway
xxx.xxx.xxx.xxx!
Set network gateway
s gateway
192.168.1.1!
Set gateway:
192.168.1.1
Please use "s net reboot!"
command or repower device
to apply new config!
DHCP on, Device can't
config gateway, set
DHCP off first.
r gateway!
Get network gateway
r gateway!
Gateway:192.168.1.1
s tcp/ip port x!
r tcp/ip port!
Set network TCP/IP port
(x=1~65535)
Get network TCP/IP port
s tcp/ip port 8000! Set TCP/IP port:8000
r tcp/ip port!
TCP/IP port:8000
s telnet port x!
Set network telnet port
(x=1~65535)
s telnet port 23!
Set Telnet port:23
r telnet port!
Get network telnet port
r telnet port!
Telnet port:23
- 23 / 25 -
Default Setting
AVG-PRO44-150 KIT
Command Code
Example
Function Description
Feedback
Network reboot…
IP Mode: Static
IP: 192.168.1.72
Subnet Mask:
255.255.255.0
Gateway: 192.168.1.1
TCP/IP port=8000
Telnet port=10
Mac address:
00:1C:91:03:80:01
s net reboot!
Reboot network modules
s net reboot!
s uart x datalen y!
Set the data length of x hdbt uart,
x=0-8, y=1-2, 1:8bit 2:7bit
hdbt uart1 data len is
s uart 1 datalen 1! 8bit
Set the baudrate of x hdbt uart ,
s uart x baudrate y! x=0-4, y=1-8, 1: 115200(Default)
2: 57600 3: 56000 4:38400
5:19200 6:14400 7:9600 8:4800
s uart x parity y!
Set the Parity of x hdbt uart,
x=0-4, y=1-3,
1:none 2:odd 3:even
s uart x type z
senddata y end!
Send data y from x hdbt uart,
z=0 ascii, z=1 hex ,x=0-4
r uart status x!
Get the Status of x hdbt uart ,
x=0-4
s uart 1
baudrate 1!
hdbt uart1 baudrate is
115200
s uart x parity 1!
hdbt uart1 parity is
none
s uart 1 type 0
hdbt uart1 data:
senddata abcdefg
abcdefg
end!
hdbt uart1 baudrate
r uart status 1!
9600,datalen 8bit,
parity none
- 24 / 25 -
Default Setting
AVG-PRO44-150 KIT
12. Application Example
Amplifier
2.0 Speakers
Power Supply
AUDIO OUT
IR IN
1
2
OUTPUT 1
HDMI
HDBT
3
4
ALL
1
2
3
4
ALL IR OUT
COAX 1
HDMI
HDBT
L+
R+
COAX 2
OUTPUT 3
OUTPUT 2
1
2
3
4
INPUT
HDMI
HDBT
L+
R+
COAX 3
L+
R+
OUTPUT 4
HDMI
COAX 4
TCP/IP
L+
R+
RS-232
100-240V AC 50/60HZ
HDBT
CONTROL
PC
TV
DC 24V
HDBT IN
TV
HDBT IN
DC 24V
DVD or Blu-ray Player
HDMI OUT
AUDIO OUT
2.0 Speakers
IR IN
HDMI OUT
AUDIO OUT
IR IN
IR OUT
IR OUT
TV
TV
The terms HDMI and HDMI High-Definition Multimedia interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI Licensing LLC in the United States and other
countries.
- 25 / 25 -