Cisco WS-C6500-SFM - Switch Installation guide

Cisco Catalyst 6500 Series Application-Oriented
Networking Module Installation Note
Product Number: WS-SVC-AON-1-K9
This publication describes how to install the Cisco Catalyst 6500 Series AON Module Services Module
(AON-SM) for the Catalyst 6500 Series switches. The AON module provides the following:
•
Enhanced security and reliability that enables reliable message delivery and provides message-level
security in addition to existing network-level security.
•
Infrastructure optimization that makes more efficient use of network resources by caching and
compressing at the message level and by integrating application and network quality-of-service
(QoS).
•
Business and infrastructure activity monitoring and management that reads into the message,
allowing the AON module to log, audit, and manage application-level business events, and combines
these events with network, server, and storage infrastructure events in a common, policy-driven
management environment.
•
Content-based routing and transformation that performs message-based routing and transformation
of protocol, content, data, and message format (for example, XML transformation).
Contents
This publication contains these sections:
•
Safety Overview, page 2
•
Front Panel Description, page 7
•
Environmental and System Requirements, page 8
•
Installing the Module, page 10
•
Verifying the Installation, page 19
•
Using the CLI, page 19
•
Related Documentation, page 20
•
Translated Safety Warnings, page 20
Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Copyright © 2004 Cisco Systems, Inc. All rights reserved.
Safety Overview
•
Obtaining Documentation, page 22
•
Documentation Feedback, page 24
•
Cisco Product Security Overview, page 24
•
Obtaining Technical Assistance, page 25
•
Obtaining Additional Publications and Information, page 26
Safety Overview
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device. Statement 1071
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
2
78-16749-01
Safety Overview
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
Avvertenza
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
78-16749-01
3
Safety Overview
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
4
78-16749-01
Safety Overview
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de
segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de
oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
78-16749-01
5
Safety Overview
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
6
78-16749-01
Front Panel Description
Front Panel Description
This section describes the physical attributes of the AON module.
Figure 1 shows the AON module front panel.
Figure 1
Application-Oriented Networking Module Front Panel
120266
WS-SVC-AONS-1
APPLICATION-ORIENTED NETWORKING
STATUS LED
Shutdown button
LEDs
When the AON module powers up, it initializes the various hardware components and communicates
with the supervisor engine. The Status LED indicates the supervisor engine operations and the
initialization results. During the normal initialization sequence, the status LED changes from off to red,
orange, and green.
Note
For more information on the supervisor engine LEDs, refer to the Catalyst 6500 Series Switch Module
Installation Guide.
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
78-16749-01
7
Environmental and System Requirements
Table 1 describes the Status LED operation.
Table 1
AON Module LEDs
LED
Color
Status
Off
Description
•
The module is waiting for the supervisor engine to provide power.
•
The module is not online.
•
The module is not receiving power, which could be caused by the following:
– Power is not available to the AON module.
– The module temperature is over the limit1.
Red
•
The module is released from reset by the supervisor engine and is booting.
•
If the boot code fails to run, the LED stays red after power up.
•
The module is initializing hardware or communicating with the supervisor
engine.
•
A fault occurred during the initialization sequence.
•
The module has failed to download its Field Programmable Gate Arrays (FPGA)
image on power up but continues with the remainder of the initialization
sequence and provides the module online status from the supervisor engine.
•
The module has not received module online status from the supervisor engine.
This problem could be caused by the supervisor engine detecting a failure in an
internal loopback test that it issued to the AON module.
Green
•
The module is operational; the supervisor engine has provided module online
status.
Green
to
orange
•
The module is disabled through the supervisor engine CLI 2 using the set module
disable mod command.
Orange
1. Enter the show environment temperature mod command to display the temperature of each of the four sensors on the AON
module.
2. CLI = command-line interface.
Environmental and System Requirements
This section describes the environmental and system requirements for the AON module:
•
Environmental Requirements, page 9
•
System Requirements, page 9
•
Memory Requirements, page 9
•
Hardware Supported, page 9
•
Power Supply, page 9
•
Software Requirements, page 10
•
Installing the Module, page 10
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
8
78-16749-01
Environmental and System Requirements
Environmental Requirements
Table 2 lists the environmental requirements for the AON module.
Table 2
AON Module Environmental Requirements
Item
Specification
Temperature, ambient operating
0o to 40oC (32o to 104oF)
Temperature, ambient nonoperating
–40o to 70oC (–40o to 158oF)
Humidity (RH), ambient (noncondensing)
operating
10% to 90%
Nonoperating relative humidity (noncondensing) 5% to 95%
System Requirements
Before you install the AON module in the Catalyst 6500 series switch, make sure that the switch meets
these hardware and software requirements:
•
Catalyst 6500 switch with 1300-AC power supply
•
Supervisor Engine 720 or Supervisor Engine 2 with a PFC2 or an MSFC2 with the Cisco IOS and
the Catalyst operating system
For more information, refer to the Catalyst 6500 Series Switch Installation Guide at
http://www.Cisco.com/univercd/home/home.htm.
For the AON software installation and configuration instructions, refer to the AON Installation and
Administration Guide.
Memory Requirements
The AON module memory is not configurable.
Hardware Supported
Before you can use the AON module, you must have a a Policy Feature Card (PFC), Supervisor Engine
720 with an MSFC3 or Supervisor Engine 2 with an MSFC2, and any module that has ports to connect
to the server and client networks.
Power Supply
You can place the AON module in any slot in the Catalyst 6500 series chassis except for slot one. The
AON module operates on power that is supplied by the chassis.
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
78-16749-01
9
Installing the Module
Software Requirements
The AON module is supported on Cisco IOS Release 12.2(17d)SXB7. The module is also supported on
Cisco IOS Release 12.(18)SXE1 with the Catalyst operating system software release 8.4(2a).
See the AON release note for software requirements.
Installing the Module
These sections describe how to install the AON module:
•
Preparing to Install the Module, page 10
•
Required Tools, page 10
•
Installing and Removing the Module, page 10
Preparing to Install the Module
Before installing the AON module, make sure that the following items are available:
•
Catalyst 6500 series switch chassis
•
Management station that is available through a Telnet or a console connection to perform the
configuration tasks
Required Tools
These tools are required to install the AON module in the Catalyst 6500 series switches:
•
Phillips-head screwdriver
•
Wrist strap or other grounding device
•
Antistatic mat or antistatic foam
Whenever you handle the AON module, always use a wrist strap or other grounding device to prevent
electrostatic discharge (ESD).
Installing and Removing the Module
Caution
During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly
touch the backplane with your hand or any metal tool, or you could shock yourself.
All Catalyst 6500 series switches support hot swapping, which allows you to install, remove, replace,
and rearrange the modules without turning off the system power. For more information on removing the
AON module from a switch, see the “Removing the Module” section on page 11.
When the switch detects that a module has been installed or removed, the system automatically runs
diagnostic and discovery routines, acknowledges the presence or absence of the module, and resumes
system operation.
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
10
78-16749-01
Installing the Module
These sections describe how to install and verify the operation of the AON module in the Catalyst 6500
series switches:
•
Slot Assignments, page 11
•
Removing the Module, page 11
•
Installing a Module, page 12
Slot Assignments
The Catalyst 6513 switch chassis has 13 slots.
•
Slot 1 is reserved for the supervisor engine.
•
Slot 2 can be used for a redundant supervisor engine if the supervisor engine in slot 1 fails.
•
If a redundant supervisor engine is not required, slots 2 through 6 on the 6-slot chassis, slots 2
through 9 on the 9-slot chassis, and slots 2 through 13 on the 13-slot chassis are available for
switching modules, such as the AON module.
•
The empty slots require filler panels, which are blank switching-module carriers that maintain
consistent airflow through the switch chassis.
Removing the Module
This section describes how to remove an existing module from a Catalyst 6500 series switch chassis.
Caution
During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly
touch the backplane with your hand or any metal tool, or you could shock yourself.
Warning
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into
beams or view directly with optical instruments.
To remove a module from the chassis, perform these steps:
Note
Step 1
Before removal, power down the module using the no power enable module slot_number command for
the Cisco IOS system software or use the set module power down slot_number command for the
Catalyst Operating System software.
Verify that the captive installation screws on all of the modules in the chassis are tight.
This step assures that the space that is created by the removed module is maintained.
Note
If the captive installation screws are loose, the electromagnetic interference (EMI) gaskets on
the installed modules will push the modules toward the open slot, reducing the opening size and
making it difficult to install the replacement module.
Step 2
Loosen the two captive installation screws on the module.
Step 3
Depending on the orientation of the slots in the chassis (horizontal or vertical), perform one of the
following sets of substeps:
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
78-16749-01
11
Installing the Module
Horizontal slots
a.
Place your thumbs on the left and right ejector levers, and simultaneously rotate the levers outward
to unseat the module from the backplane connector.
b.
Grasp the front edge of the module, and slide the module part of the way out of the slot. Place your
other hand under the module to support the weight of the module. Do not touch the module circuitry.
Vertical slots
a.
Place your thumbs on the ejector levers that are located at the top and bottom of the module, and
simultaneously rotate the levers outward to unseat the module from the backplane connector.
b.
Grasp the edges of the module, and slide the module straight out of the slot. Do not touch the module
circuitry.
Step 4
Place the module on an antistatic mat or antistatic foam, or immediately reinstall it in another slot.
Step 5
If the slot from which you removed the module is to remain empty, install a module filler panel to keep
dust out of the chassis and to maintain proper airflow through the chassis.
Warning
Blank faceplates (filler panels) serve three important functions: they prevent exposure to hazardous
voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might
disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate
the system unless all cards and faceplates are in place.
Installing a Module
This section describes how to install a module in the Catalyst 6500 series switch.
Caution
To prevent ESD damage, handle modules by the carrier edges only.
Caution
During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly
touch the backplane with your hand or any metal tool, or you could shock yourself.
Warning
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into
beams or view directly with optical instruments.
To install a module in the chassis, perform these steps:
Step 1
Choose a slot for the module.
Step 2
Verify that there is enough clearance to accommodate any interface equipment that you will connect
directly to the module ports. If possible, place the modules between the empty slots that contain only
the module filler panels.
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
12
78-16749-01
Installing the Module
Step 3
Verify that the captive installation screws are tightened on all modules installed in the chassis.
This action ensures that the EMI gaskets on all modules are fully compressed to maximize the opening
space for the replacement module.
Note
If the captive installation screws are loose, the EMI gaskets on the installed modules will push
adjacent modules toward the open slot, reducing the opening size and making it difficult to
install the replacement module.
Step 4
Remove the module filler panel by removing the two Phillips pan-head screws from the filler panel. (To
remove a module, refer to the “Removing the Module” section on page 11.)
Step 5
Fully open both ejector levers on the new or replacement module. (See Figure 2.)
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
78-16749-01
13
Installing the Module
Figure 2
Positioning the Module in a Horizontal Slot Chassis
Insert module
between slot guides
EMI gasket
3
4
5
6
4
5
6
WS-X6K-SUP2-2GE
1
T
E
US
NS
ST
SY
GM
OL
EM
AT
ST
R
CO
M
Switch
100%
T
SE
PW
Load
CONSOLE
PORT
MODE
RE
PORT 1
PORT 2
CONSOLE
SUPERVISOR2
PCMCIA
EJECT
1%
WS-X6K-SUP2-2GE
2
T
E
US
ST
NS
ST
SY
GM
OL
EM
AT
CO
R
PW
M
Switch
100%
T
SE
Load
CONSOLE
PORT
MODE
RE
PORT 1
PORT 2
CONSOLE
SUPERVISOR2
PCMCIA
EJECT
1%
3
4
FAN
STATUS 5
6
WS-X6224
US
VE
AT
TI
AC
SE
LE
24 PORT 100FX
NE
EMI gasket
CT
XT
58569
ST
o
o
INPUT
OK
FAN
OK
OUTPUT
FAIL
INPUT
OK
FAN
OK
OUTPUT
FAIL
WS-C6500-SFM
US
AT
ST
E
TIV
AC
SWITCH FABRIC MDL
Ejector lever fully
extended
Step 6
Depending on the orientation of the slots in the chassis (horizontal or vertical), perform one of the
following sets of substeps:
Horizontal slots
a.
Position the module in the slot. Make sure that you align the sides of the module carrier with the slot
guides on each side of the slot. (See Figure 2.)
b.
Carefully slide the module into the slot until the EMI gasket along the top edge of the module makes
contact with the module in the slot above it and both ejector levers have closed to approximately
45 degrees with respect to the module faceplate. (See Figure 3.)
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
14
78-16749-01
Installing the Module
Figure 3
Clearing the EMI Gasket in a Horizontal Slot Chassis
WS-X6K-SUP2-2GE
1
US
AT
ST
LE
EM
ST
SY
O
NS
CO
PW
M
R
G
M
T
Switch
100%
T
SE
RE
CONSOLE
Load
CONSOLE
PORT
MODE
SUPERVISOR2
PORT 1
PCMCIA
PORT 2
EJECT
1%
WS-X6K-SUP2-2GE
NK
LI
2
US
AT
ST
M
G
O
NS
CO
NK
LI
T
LE
EM
ST
SY
M
R
PW
Switch
100%
T
SE
RE
CONSOLE
SUPERVISOR2
CONSOLE
PORT
MODE
Load
PORT 1
PCMCIA
PORT 2
EJECT
1%
NK
LI
NK
LI
3
Press down
4
FAN
STATUS 5
Press down
WS-X6224
S
TU
VE
TI
STA
AC
CT
LE
SE
24 PORT 100FX
XT
NE
6
3
4
4
WS-C6500-SFM
5
US
AT
SWITCH FABIR
ST
D MDL
6
c.
Caution
E
TIV
AC
1 mm Gap between the module
EMI gasket and the
module above it
58570
5
6
Using the thumb and forefinger of each hand, grasp the two ejector levers and press down to create
a small (0.040 inch [1 mm]) gap between the EMI gasket and the module above it. (See Figure 3.)
Pressing down too firmly on the levers will bend and damage them.
d.
While pressing down, simultaneously close the left and right ejector levers to fully seat the module
in the backplane connector. The ejector levers are fully closed when they are flush with the module
faceplate. (See Figure 4.)
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
78-16749-01
15
Installing the Module
Figure 4
Ejector Lever Closure in a Horizontal Slot Chassis
WS-X6K-SUP2-2GE
1
US
AT
ST
LE
EM
ST
SY
O
NS
CO
PW
R
M
G
M
T
Switch
100%
T
SE
RE
CONSOLE
SUPERVISOR2
Load
CONSOLE
PORT
MODE
PORT 1
PCMCIA
PORT 2
EJECT
1%
WS-X6K-SUP2-2GE
NK
LI
2
US
AT
ST
LE
EM
ST
SY
O
NS
CO
PW
R
M
G
M
NK
LI
T
Switch
100%
T
SE
RE
CONSOLE
SUPERVISOR2
Load
CONSOLE
PORT
MODE
PORT 1
PCMCIA
PORT 2
EJECT
1%
NK
LI
NK
LI
3
4
FAN
STATUS 5
WS-C6500-SFM
S
TU
STA
CT
VE
TI
AC
LE
SE
SWITCH FABRIC MDL
XT
NE
58571
6
Ejector levers flush
with module faceplate
Note
e.
Failure to fully seat the module in the backplane connector can result in error messages.
Tighten the two captive installation screws on the module.
Note
Make sure that the ejector levers are fully closed before tightening the captive installation
screws.
Vertical slots
a.
Position the module in the slot. (See Figure 5.) Make sure that you align the sides of the module
carrier with the slot guides on the top and bottom of the slot.
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
16
78-16749-01
Installing the Module
Figure 5
Positioning the Module in a Vertical Slot Chassis
Ejector lever fully
extended
WS-C6500-SFM
SWITCH FABRIC MDL
FAN
STATUS
WS-X6K-SUP2-2GE
MT
OLE MG
TEM NS
TUS
R
SET
RE
PW
SYS
CO
STA
MT
E
M
S
OL
T
MG
TU
R
NS
SE
STE
RE
PW
CO
SY
STA
WS-X6K-SUP2-2GE
SUPERVISOR2
SUPERVISOR2
ST
AT
CONSOLE
CONSOLE
US
AC
PORT
CONSOLE
PORT
MODE
MODE
WS-X6224
24 PORT 100FX
CONSOLE
TIV
E
US
AT
ST
E
TIV
AC
PCMCIA
PCMCIA
EJECT
EJECT
Switch
Switch
1%
100%
1%
100%
Load
Load
EMI
gasket
PORT 1
PORT 1
PORT 2
PORT 2
XT
CT
LE
SE
NE
63585
EMI
gasket
o
o
INPUT
OK
FAN
OK
OUTPUT
FAIL
INPUT
OK
FAN
OK
OUTPUT
FAIL
6
Insert module
between slot guides
3
4
b.
Carefully slide the module into the slot until the EMI gasket along the right edge of the module
makes contact with the module in the slot adjacent to it and both ejector levers have closed to
approximately 45 degrees with respect to the module faceplate. (See Figure 6.)
c.
Using the thumb and forefinger of each hand, grasp the two ejector levers and exert a slight pressure
to the left, deflecting the module approximately 0.040 inches (1 mm) to create a small gap between
the modules EMI gasket and the module adjacent to it. (See Figure 6.)
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
78-16749-01
17
Installing the Module
Figure 6
Clearing the EMI Gasket in a Vertical Slot Chassis
Gap between the module
EMI gasket and the
module above it
1 mm
WS-C6500-SFM
SWITCH FABIRD MDL
S
TU
A
ST
E
TIV
AC
FAN
STATUS
WS-X6K-SUP2-2GE
MT
E
M
S
OL
T
MG
TU
R
NS
SE
STE
RE
PW
CO
SY
STA
US
AT
ST
MT
OLE MG
TEM NS
TUS
R
SET
RE
PW
SYS
CO
STA
WS-X6K-SUP2-2GE
SUPERVISOR2
SUPERVISOR2
WS-X6224
24 PORT 100FX
CONSOLE
CONSOLE
E
TIV
AC
PORT
MODE
PORT
MODE
CONSOLE
CONSOLE
Press left
PCMCIA
PCMCIA
EJECT
EJECT
Switch
Switch
1%
100%
1%
100%
Load
Load
PORT 1
PORT 1
CT
LE
SE
XT
NE
Press left
63586
PORT 2
PORT 2
o
o
INPUT
OK
FAN
OK
OUTPUT
FAIL
INPUT
OK
Caution
FAN
OK
OUTPUT
FAIL
Exerting too much pressure on the ejector levers will bend and damage them.
d.
While pressing on the ejector levers, simultaneously close them to fully seat the module in the
backplane connector. The ejector levers are fully closed when they are flush with the module
faceplate. (See Figure 7.)
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
18
78-16749-01
Verifying the Installation
Figure 7
Ejector Lever Closure in a Vertical Slot Chassis
FAN
STATUS
T
M
LE
G
O
T
M
EM
US
R
NS
SE
ST
AT
RE
PW
SY
CO
ST
CO
EM
ST
SY
O
NS
PW
LE
STA
R
T
CONSOLE
CONSOLE
VE
TI
AC
SE
T
M
RE
G
S
M
TU
CONSOLE
PORT
MODE
CONSOLE
PORT
MODE
PCMCIA
PCMCIA
EJECT
EJECT
1%
Switch
Switch
100%
1%
100%
Load
Load
PORT 1
PORT 1
XT
WS-X6K-SUP2-2GE
SUPERVISOR2
US
AT
ST
WS-X6K-SUP2-2GE
SUPERVISOR2
WS-X6224
24 PORT 100FX
NE
SE
LE
CT
63587
PORT 2
PORT 2
All ejector levers flush
with module faceplate
e.
Tighten the two captive installation screws on the module.
Note
Make sure that the ejector levers are fully closed before tightening the captive installation
screws.
Verifying the Installation
When you install the module into the Catalyst 6500 series switch, the module goes through a startup
sequence that requires no intervention. At the successful conclusion of the startup sequence, the green
Status LED will light and remain on. If the Status LED does not show green, or if it shows a different
color, refer to Table 1 on page 8 to determine the modules status.
For software installation and configuration instructions, refer to the AON Installation and Administration
Guide.
Using the CLI
The software interface for the module is the Cisco IOS and the Catalyst operating system command-line
interface accessed through a Telnet connection to the switch or through the switch console interface.
Refer to the Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide and the Catalyst 6500
Series Switch Software Configuration Guide for details.
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
78-16749-01
19
Related Documentation
To understand the Cisco IOS command-line interface and Cisco IOS command modes, refer to
Chapter 2, “Command-Line Interfaces,” in the Catalyst 6500 Series Switch Cisco IOS Software
Configuration Guide.
To understand the Catalyst operating system command-line interface and Catalyst operating system
command modes, refer to Chapter 2, “Command-Line Interfaces,” in the Catalyst 6500 Series Switch
Configuration Guide.
You configure the module using the session command.
You can session into the module from the switch console and configure the module. The session is a
Telnet interface through the Ethernet out-of-band channel (EOBC) of the switch backplane.
Related Documentation
For more detailed installation and configuration information for the AON module, refer to the following
publications:
•
Release Notes for Cisco Application-Oriented Networking
•
AON Installation and Administration Guide
•
AON Development Studio User
•
Regulatory Compliance and Safety Information for the Catalyst 6500 Series Switches
Translated Safety Warnings
Warning
Waarschuwing
Varoitus
Invisible laser radiation present. Statement 1016
Onzichtbare laserstraling aanwezig.
Näkymättömiä lasersäteitä.
Attention
Rayonnement laser actif mais invisible.
Warnung
Unsichtbare Laserstrahlung.
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Radiazione laser invisibile.
Usynlig laserstråling.
Radiação laser invisível presente.
Existe radiación láser invisible.
Nu pågående osynlig laserstrålning.
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
20
78-16749-01
Translated Safety Warnings
Warning
Blank faceplates and cover panels serve three important functions: they prevent exposure to
hazardous voltages and currents inside the chassis; they contain electromagnetic interference
(EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis.
Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place.
Statement 1029
Waarschuwing
Lege vlakplaten en afdekpanelen vervullen drie belangrijke functies: ze voorkomen blootstelling
aan gevaarlijke voltages en stroom binnenin het frame, ze bevatten elektromagnetische storing
(EMI) hetgeen andere apparaten kan verstoren en ze leiden de stroom van koellucht door het frame.
Het systeem niet bedienen tenzij alle kaarten, vlakplaten en afdekkingen aan de voor- en achterkant
zich op hun plaats bevinden.
Varoitus
Tyhjillä tasolaikoilla ja suojapaneeleilla on kolme tärkeää käyttötarkoitusta: Ne suojaavat
asennuspohjan sisäisille vaarallisille jännitteille ja sähkövirralle altistumiselta; ne pitävät
sisällään elektromagneettisen häiriön (EMI), joka voi häiritä muita laitteita; ja ne suuntaavat
tuuletusilman asennuspohjan läpi. Järjestelmää ei saa käyttää, elleivät kaikki tasolaikat, etukannet
ja takakannet ole kunnolla paikoillaan.
Attention
Ne jamais faire fonctionner le système sans que l’intégralité des cartes, des plaques métalliques et
des panneaux avant et arrière ne soient fixés à leur emplacement. Ceux-ci remplissent trois
fonctions essentielles : ils évitent tout risque de contact avec des tensions et des courants
dangereux à l’intérieur du châssis, ils évitent toute diffusion d’interférences électromagnétiques
qui pourraient perturber le fonctionnement des autres équipements, et ils canalisent le flux d’air de
refroidissement dans le châssis.
Warnung
Blanke Faceplates und Abdeckungen haben drei wichtigen Funktionen: (1) Sie schützen vor
gefährlichen Spannungen und Strom innerhalb des Chassis; (2) sie halten elektromagnetische
Interferenzen (EMI) zurück, die andere Geräte stören könnten; (3) sie lenken den kühlenden
Luftstrom durch das Chassis. Das System darf nur betrieben werden, wenn alle Karten, Faceplates,
Voder- und Rückabdeckungen an Ort und Stelle sind.
Avvertenza
Le piattaforme bianche e i panelli di protezione hanno tre funzioni importanti: Evitano l'esposizione
a voltaggi e correnti elettriche pericolose nello chassis, trattengono le interferenze
elettromagnetiche (EMI) che potrebbero scombussolare altri apparati e dirigono il flusso di aria per
il raffreddamento attraverso lo chassis. Non mettete in funzione il sistema se le schede, le
piattaforme, i panelli frontali e posteriori non sono in posizione.
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
78-16749-01
21
Obtaining Documentation
Advarsel
Blanke ytterplater og deksler sørger for tre viktige funksjoner: de forhindrer utsettelse for farlig
spenning og strøm inni kabinettet; de inneholder elektromagnetisk forstyrrelse (EMI) som kan
avbryte annet utstyr, og de dirigerer luftavkjølingsstrømmen gjennom kabinettet. Betjen ikke
systemet med mindre alle kort, ytterplater, frontdeksler og bakdeksler sitter på plass.
Aviso
As faces furadas e os painéis de protecção desempenham três importantes funções: previnem
contra uma exposição perigosa a voltagens e correntes existentes no interior do chassis; previnem
contra interferência electromagnética (EMI) que poderá danificar outro equipamento; e canalizam
o fluxo do ar de refrigeração através do chassis. Não deverá operar o sistema sem que todas as
placas, faces, protecções anteriores e posteriores estejam nos seus lugares.
¡Advertencia!
Las placas frontales y los paneles de relleno cumplen tres funciones importantes: evitan la
exposición a niveles peligrosos de voltaje y corriente dentro del chasis; reducen la interferencia
electromagnética (EMI) que podría perturbar la operación de otros equipos y dirigen el flujo de aire
de enfriamiento a través del chasis. No haga funcionar el sistema a menos que todas las tarjetas,
placas frontales, cubiertas frontales y cubiertas traseras estén en su lugar.
Varning!
Tomma framplattor och skyddspaneler har tre viktiga funktioner: de förhindrar att personer utsätts
för farlig spänning och ström som finns inuti chassit; de innehåller elektromagnetisk interferens
(EMI) som kan störa annan utrustning; och de styr riktningen på kylluftsflödet genom chassit. Använd
inte systemet om inte alla kort, framplattor, fram- och bakskydd är på plats.
Obtaining Documentation
Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several
ways to obtain technical assistance and other technical resources. These sections explain how to obtain
technical information from Cisco Systems.
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
22
78-16749-01
Obtaining Documentation
Cisco.com
You can access the most current Cisco documentation at this URL:
http://www.cisco.com/techsupport
You can access the Cisco website at this URL:
http://www.cisco.com
You can access international Cisco websites at this URL:
http://www.cisco.com/public/countries_languages.shtml
Product Documentation DVD
Cisco documentation and additional literature are available in the Product Documentation DVD package,
which may have shipped with your product. The Product Documentation DVD is updated regularly and
may be more current than printed documentation.
The Product Documentation DVD is a comprehensive library of technical product documentation on
portable media. The DVD enables you to access multiple versions of hardware and software installation,
configuration, and command guides for Cisco products and to view technical documentation in HTML.
With the DVD, you have access to the same documentation that is found on the Cisco website without
being connected to the Internet. Certain products also have .pdf versions of the documentation available.
The Product Documentation DVD is available as a single unit or as a subscription. Registered Cisco.com
users (Cisco direct customers) can order a Product Documentation DVD (product number
DOC-DOCDVD=) from the Ordering tool or Cisco Marketplace.
Cisco Ordering tool:
http://www.cisco.com/en/US/partner/ordering/
Cisco Marketplace:
http://www.cisco.com/go/marketplace/
Ordering Documentation
Beginning June 30, 2005, registered Cisco.com users may order Cisco documentation at the Product
Documentation Store in the Cisco Marketplace at this URL:
http://www.cisco.com/go/marketplace/
Cisco will continue to support documentation orders using the Ordering tool:
•
Registered Cisco.com users (Cisco direct customers) can order documentation from the
Ordering tool:
http://www.cisco.com/en/US/partner/ordering/
•
Instructions for ordering documentation using the Ordering tool are at this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm
•
Nonregistered Cisco.com users can order documentation through a local account representative by
calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in
North America, by calling 1 800 553-NETS (6387).
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
78-16749-01
23
Documentation Feedback
Documentation Feedback
You can rate and provide feedback about Cisco technical documents by completing the online feedback
form that appears with the technical documents on Cisco.com.
You can send comments about Cisco documentation to bug-doc@cisco.com.
You can submit comments by using the response card (if present) behind the front cover of your
document or by writing to the following address:
Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883
We appreciate your comments.
Cisco Product Security Overview
Cisco provides a free online Security Vulnerability Policy portal at this URL:
http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html
From this site, you can perform these tasks:
•
Report security vulnerabilities in Cisco products.
•
Obtain assistance with security incidents that involve Cisco products.
•
Register to receive security information from Cisco.
A current list of security advisories and notices for Cisco products is available at this URL:
http://www.cisco.com/go/psirt
If you prefer to see advisories and notices as they are updated in real time, you can access a Product
Security Incident Response Team Really Simple Syndication (PSIRT RSS) feed from this URL:
http://www.cisco.com/en/US/products/products_psirt_rss_feed.html
Reporting Security Problems in Cisco Products
Cisco is committed to delivering secure products. We test our products internally before we release them,
and we strive to correct all vulnerabilities quickly. If you think that you might have identified a
vulnerability in a Cisco product, contact PSIRT:
•
Emergencies — security-alert@cisco.com
An emergency is either a condition in which a system is under active attack or a condition for which
a severe and urgent security vulnerability should be reported. All other conditions are considered
nonemergencies.
•
Nonemergencies — psirt@cisco.com
In an emergency, you can also reach PSIRT by telephone:
•
1 877 228-7302
•
1 408 525-6532
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
24
78-16749-01
Obtaining Technical Assistance
Tip
We encourage you to use Pretty Good Privacy (PGP) or a compatible product to encrypt any sensitive
information that you send to Cisco. PSIRT can work from encrypted information that is compatible with
PGP versions 2.x through 8.x.
Never use a revoked or an expired encryption key. The correct public key to use in your correspondence
with PSIRT is the one linked in the Contact Summary section of the Security Vulnerability Policy page
at this URL:
http://www.cisco.com/en/US/products/products_security_vulnerability_policy.htm
The link on this page has the current PGP key ID in use.
Obtaining Technical Assistance
Cisco Technical Support provides 24-hour-a-day award-winning technical assistance. The Cisco
Technical Support & Documentation website on Cisco.com features extensive online support resources.
In addition, if you have a valid Cisco service contract, Cisco Technical Assistance Center (TAC)
engineers provide telephone support. If you do not have a valid Cisco service contract, contact your
reseller.
Cisco Technical Support & Documentation Website
The Cisco Technical Support & Documentation website provides online documents and tools for
troubleshooting and resolving technical issues with Cisco products and technologies. The website is
available 24 hours a day, at this URL:
http://www.cisco.com/techsupport
Access to all tools on the Cisco Technical Support & Documentation website requires a Cisco.com user
ID and password. If you have a valid service contract but do not have a user ID or password, you can
register at this URL:
http://tools.cisco.com/RPF/register/register.do
Note
Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting
a web or phone request for service. You can access the CPI tool from the Cisco Technical Support &
Documentation website by clicking the Tools & Resources link under Documentation & Tools. Choose
Cisco Product Identification Tool from the Alphabetical Index drop-down list, or click the Cisco
Product Identification Tool link under Alerts & RMAs. The CPI tool offers three search options: by
product ID or model name; by tree view; or for certain products, by copying and pasting show command
output. Search results show an illustration of your product with the serial number label location
highlighted. Locate the serial number label on your product and record the information before placing a
service call.
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
78-16749-01
25
Obtaining Additional Publications and Information
Submitting a Service Request
Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3
and S4 service requests are those in which your network is minimally impaired or for which you require
product information.) After you describe your situation, the TAC Service Request Tool provides
recommended solutions. If your issue is not resolved using the recommended resources, your service
request is assigned to a Cisco engineer. The TAC Service Request Tool is located at this URL:
http://www.cisco.com/techsupport/servicerequest
For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone.
(S1 or S2 service requests are those in which your production network is down or severely degraded.)
Cisco engineers are assigned immediately to S1 and S2 service requests to help keep your business
operations running smoothly.
To open a service request by telephone, use one of the following numbers:
Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553-2447
For a complete list of Cisco TAC contacts, go to this URL:
http://www.cisco.com/techsupport/contacts
Definitions of Service Request Severity
To ensure that all service requests are reported in a standard format, Cisco has established severity
definitions.
Severity 1 (S1)—Your network is “down,” or there is a critical impact to your business operations. You
and Cisco will commit all necessary resources around the clock to resolve the situation.
Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your
business operation are negatively affected by inadequate performance of Cisco products. You and Cisco
will commit full-time resources during normal business hours to resolve the situation.
Severity 3 (S3)—Operational performance of your network is impaired, but most business operations
remain functional. You and Cisco will commit resources during normal business hours to restore service
to satisfactory levels.
Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or
configuration. There is little or no effect on your business operations.
Obtaining Additional Publications and Information
Information about Cisco products, technologies, and network solutions is available from various online
and printed sources.
•
Cisco Marketplace provides a variety of Cisco books, reference guides, documentation, and logo
merchandise. Visit Cisco Marketplace, the company store, at this URL:
http://www.cisco.com/go/marketplace/
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
26
78-16749-01
Obtaining Additional Publications and Information
•
Cisco Press publishes a wide range of general networking, training and certification titles. Both new
and experienced users will benefit from these publications. For current Cisco Press titles and other
information, go to Cisco Press at this URL:
http://www.ciscopress.com
•
Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and
networking investments. Each quarter, Packet delivers coverage of the latest industry trends,
technology breakthroughs, and Cisco products and solutions, as well as network deployment and
troubleshooting tips, configuration examples, customer case studies, certification and training
information, and links to scores of in-depth online resources. You can access Packet magazine at
this URL:
http://www.cisco.com/packet
•
iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies
learn how they can use technology to increase revenue, streamline their business, and expand
services. The publication identifies the challenges facing these companies and the technologies to
help solve them, using real-world case studies and business strategies to help readers make sound
technology investment decisions. You can access iQ Magazine at this URL:
http://www.cisco.com/go/iqmagazine
or view the digital edition at this URL:
http://ciscoiq.texterity.com/ciscoiq/sample/
•
Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering
professionals involved in designing, developing, and operating public and private internets and
intranets. You can access the Internet Protocol Journal at this URL:
http://www.cisco.com/ipj
•
Networking products offered by Cisco Systems, as well as customer support services, can be
obtained at this URL:
http://www.cisco.com/en/US/products/index.html
•
Networking Professionals Connection is an interactive website for networking professionals to
share questions, suggestions, and information about networking products and technologies with
Cisco experts and other networking professionals. Join a discussion at this URL:
http://www.cisco.com/discuss/networking
•
World-class networking training is available from Cisco. You can view current offerings at
this URL:
http://www.cisco.com/en/US/learning/index.html
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
78-16749-01
27
Obtaining Additional Publications and Information
This document is to be used in conjunction with the documents listed in the “Related Documentation” section.
CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work,
Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP,
CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital,
the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, FormShare, GigaDrive, GigaStack, HomeLink,
Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo,
Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet,
The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the
United States and certain other countries.
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a
partnership relationship between Cisco and any other company. (0601R)
Copyright © 2005 Cisco Systems, Inc. All rights reserved.
Cisco Catalyst 6500 Series Application-Oriented Networking Module Installation Note
28
78-16749-01