Motorline professional VARANDA Installation Manual

Installation manual
VARANDA AWNING
V2.0 REV20220825
PRE-INSTALLATION INFORMATION
2 people
Necessary tools
Important
!
tuning key
included
1
Before Installation, check the levelness of the place
where you are going to apply the awning. Dimensions
must be parallel and level. If the balcony is not level,
it is necessary to apply
shims that allow the awning fixing plates to be
correctly installed.
Nº10
Varanda
Inside the package
Ce
Bc
CI
Variable number
and format
Sp
Eb
Rt
Si
St
Po2
Po1
Eq
Note: Screws included, with the exception of screws that will connect St to a structure of the customer's choice.
Preparation of the cassete and front profile
2
Bc
A Disassemble
B Assemble
C Slide front profile on fabric
D Assemble again
Po1
Place in center
Preparation of fixing supports
3
A Insert
CI
Example for 6 sets of parts (Sp,
Si, St x 6), 3 sets for each
support:
Top
Bottom
Sp
max. 100cm
B
Screw SI to Sp that is inserted into CI
respecting the measurements shown on
the side.
max. 100cm
max. 20cm
Sp
Si
Make the same assembly for the other CI profile.
Assemble
Eq
4
Placement of fixing plates
Varanda without support tubes
B
A
Si
St
St's distances will be equal to SI's distances in CI.
D
C
E
min. 30cm
CI
Make a mark where you will drill.
Drill in the marked areas.
Screw St to the perforated base.
Screw St to SI. Repeat, as many
times as necessary, all processes
for the installation to complete.
F
Attention, it is necessary to respect the position shown
above to assemble the cassette together.
Varanda with support tubes
A
B
C
D
E
min. 30cm
CI
F
Support tube example
Attention, it is necessary to respect the position shown
above to assemble the cassette together.
Adapt the fixing of the awning to the type of balcony you have.
G
5
Other supports
Varanda without support tubes
Simple guide
Dual Guide
Varanda with support tubes
Simple guide
Dual Guide
Cassette installation
6
A
C
B
Placement of the maneuver rope
7
A
Disassemble
50cm
Attention, for the awning to function correctly, pay
close attention to the following instructions.
Operation to be carried out on the 2 reinforcements.
B
Face
50cm
D
Eb
Cover
C
Front profile
B Face
Cover
Winding direction
P1
C
to
All respecting the winding direction, make 3 courses
of the wire around the winding tube pulley and fix.
Pass the thread under the pulley P1 by sliding it
through the guide and finding the bottom cover at C.
from
Attention, from B to
C, make sure that
the rope does not
wrap itself, as it may
break after a lot of
use.
to
B
D
Eb
OK
Then, slide the rope through the profile, pass
the rope through the pulley and slide it again
along the profile to the load bar.
Attention: the cover will be placed when the
rope is tensioned.
Direction of travel
the rope takes when
it is assembled
(overview)
C
from B
to D
NOT
P1
Eb
P2
cm
20
D Front profile
1
3
2 part pre-assembly
Ac
Rt
Po2
Ac
Pin up
Po2
to Po1
2
from
8
D
Po2
Po1
Note:
1) Pulley Po1 must be placed in
the middle of the front profile.
2) Po1 → Ac = 20cm
3) The rope passes first under and
then over Po1.
P2
Fabric tension
Pull the end of the rope by hand and lock in the grip. The tension must be identical on both sides, to verify that the pulley is well positioned
in the center of the front profile. Make sure the rope is properly guided on all the pulleys in the system. Open the awning all the way down.
Place the awning with 50 cm of opening, to make more tension of the rope. Perform an opening and closing maneuver. The fabric must be
taut.
9
Limit switch regulation
Course stoppers are factory preset. To manually adjust see next page.
10 Finalization
After the adjustments have been made, replace the cassette cover and the front profile cover by tightening the two screws.
End of assembly
Consumer information
1
Electronic operation
Use the remote control to open and/or close the awning electronically.
Open
B
Close
A
A
2
B
Manual operation
In the event of a breakdown or power failure, use the awning in manual mode with the help of the emergency crank.
B
A
B
Insert the emergency crank as indicated in the figure above.
3
A
To open, turn the emergency crank to the right. To close, turn the emergency crank to the left.
Limit switch regulation
A
Course stoppers are factory preset. To adjust, open
the awning. Then open the cassette and on the right
side you will see the mechanism as shown in the
figure to the side.
A To adjust the closing:
- Close the awning and then open it up to 30cm;
- On the mechanism, use the tuning key on the
lower protrusion;
- When turning to the right, the awning closes more;
- When turning to the left the awning opens more.
To adjust the opening:
- Awning open to the end;
- On the mechanism, use the tuning key on the
upper protrusion;
- When turning to the right, the awning opens more;
- When turning to the left, the awning closes more.
B
Note: When regulating several times, the motor may need
to rest.
opens more
closes more
Limit switch - closing
B
closes more
opens more
Limit switch - opening
Awning maintenance tips
An awning is subject to some adverse situations: humidity, sea air, counterweight, wind, among others. We recommend:
- check the tightness of screws and limit switches after installation and regularly at the beginning and end of each season;
- never roll up a wet awning. Dry it if possible;
- clean the fabric and frame at the beginning and end of each season. Attention, never use detergents.
Problems
Causes
Solutions
Varanda awning disintegrated
from the structure.
The fixing supports are not adapted to the
structure's composition.
The front profile does not work
normally.
The rope came off from a pulley. The tension
of one rope is higher than the other (pulley
Po1 off-center).
Check the entire rope circuit for possible rope
displacement (paragraph 6).
Check that the tension is identical on both sides
(pulley Po1 centered - paragraph 6).
The fabric is not stretched.
Incorrect tension in the base.
Fabric deformation (Natural effect).
Tighten the rope (paragraph 7).
The awning does not open or close.
Rupture of the rope.
Faulty electrical maneuver.
Do the complete circuit of the rope again (par. 6).
Test the electrical part to find the problem.
The electric awning maneuvers do
not work.
The motor goes into thermal protection after
two successive descents and one ascent.
Wait for the end of protection (20 minutes).
The electric awning maneuvers do
not work.
Connection problem.
Check the correct placement of the supports (as
indicated in the manual).
In case of fixing with a chemical anchor bolt, report
to the manufacturer.
Check the motor connection.
Check the operation of the motor by connecting
directly to the electrical input (blue black or blue brown).
Do not install the awning in the event of:
Wind
Rain
Snow
Nothing suspended
EXPLODED VIEW
9
7
10
11
8
6
12
5
4
3
13
15
14
16
2
1
17
18
TVAR08
TVAR07
TVAR10
Number
Reference
Designation
1
TVAR19
Cassette Guide
2
TVAR04/05
Cassette lateral covers
3
MTTCU14A
Tube Support Ø 78mm
4
MTC678P
Tube Bushing Ø 78mm
5
TVAR17
Cassette pulley
6
MTL001
Tube Ø 78mm
7
TVAR14/15
Cassette Superior Profiles
8
TVAR13
Cassette Bottom Profile
9
TUB90M8MT
Tubular motor
10
TVAR24
Motor support
11
TVAR01
Guide
12
TVAR16
Guide cover
13
TVAR06
Strut cover
14
TVAR03
Strut profile
15
TVAR02
Strut Profile Cover
16
TVAR23
Fabric Tension Pulley
17
TVAR22
Fabric Tension Spring Pulley
18
TVAR09
Fabric Tension Spring
N.R*
TVAR18
Rope
N.R*
TVAR20/21
Rope Brakes
* the part is not represented