sunsei CC20000D Manual

sunsei CC20000D Manual

The Sunsei CC20000D is a reliable charge controller ideal for Sunsei solar panels. It efficiently charges batteries, providing overcharge protection and maximizing battery life. Features like digital voltage and current readouts, status lights, and adjustable set-points make monitoring and customization easy. It can handle up to 20 amps of continuous charging current, making it suitable for various home, RV, and marine solar systems.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Sunsei CC20000D Manual - Charge Controller for Home, RV, & Marine | Manualzz
The Ideal Charge Controller for Home, RV & Marine Solar Systems
The SunseiTM CC20000D is a highly reliable charge controller that is ideal for
the SunseiTM SolarCharger SE-4000, SE-6000 and SE-8000 solar panels. It will
efficiently charge your batteries and provide years of protection from
overcharging. This protective care will prolong your battery life and reduce
maintenance requirements.
FEATURES
IDEAL SOLAR CHARGING
• Compatible – Works with almost all
types of batteries and solar panels
• Efficient – Over 95% efficiency when
charging
• Full Charging – Ensures that the
batteries are always topped off
• Battery Safe – Charging method
maximizes battery life
• Reduced Maintenance – From
healthy charging and reliable
operation
OVER-CHARGE PROTECTION
• High Voltage “Shut-off” – Shuts off
only when battery is full
• Robust Circuitry – Control function
100% solid state
HIGH RELIABILITY
• Simple, rugged electronics – Low
component count and streamlined
design ensure long-term reliability
• No Minimum Voltage Required –
Can charge a dead battery
FEATURES
• Digital Voltage and Current – Accurate
readout for battery and solar panels
• Status Lights – Colored BATTERY
condition bar-graph with “CHARGING”
and “CHARGED” lights
• Adjustable Set-point – Easily adjusts
to higher or lower voltages
• Reverse leakage protection –
Prevents power loss at night.
• Over-current & Incorrect Wiring
Protection – ARRAY and BATTERY
fuse
• Terminal Block – For sound and easy
wire connections
• Mounting Options – Can mount flush
or onto a wall (with accessory)
• Environmental Protection – Front
plate and circuitry have moisture
protection
SYSTEM COMPATIBILITY
RFNoise
Noise– –Low-switching
Low-switching
• Minimum RF
frequency minimizes electronic noise
External RF
RF Noise
Noise ––
• Protection from External
Can operate with noisy inverters
2
Specifications
PARAMETERS
UNITS
SunseiTM
CC20000D
Nominal Voltage
Array Voltage, Max (Voc)
Volts
Volts
12
26
Charging Current, Continuous (Isc)
Charging Current, Max (60 seconds)
Amps
Amps
20
25
Volts
Volts
Volts
0
7.8
10.5
Milliamps
Milliamps
Milliamps per LED
Volts
Volts
Volts
8.8
12.8
5
14.4 + .2
13.6 – 15.3
13.0 + .2
Volts per Amp
Volts per Amp
0.05
0.08
°C (°F)
°C (°F)
0.5 %
1%
-30 to 50 (-22 to 122)
-40 to 70 (-40 to 158)
Operating Voltage at Battery, Min
Charge Control
LCD Metering
LED Bar-graph
Current Consumption
Quiescent (Tare)
Charging (with LED Bar-graph off)
LED Bar-graph
Charge Termination, Factory Set (1)
Charge Termination, Adjustable Range (2)
Charge Resumption, Factory Set (2)
Voltage Drop, Array to Battery
Controller
Controller and 2 fuses
LCD Meter Accuracy
DC Voltage
DC Current
Operating Temperature Range
Storage Temperature Range
4x7 BOX (ACCESSORY)
In Inches (cm)
Notes:
(1) This is not a constant voltage controller.
The batteries will drop below this
voltage when completely charged.
5.0 (12.7)
Dia:
.275 (.7)
1.75
(4.4)
(2) The Charge Termination / Resumption
span is fixed. The Resumption set-point
changes as the Termination set-point is
adjusted.
3.75
(9.5)
7.0 (17.8)
CERTIFICATIONS
Not all units are certified. Refer to logos on product (back) for certifications.
Recognized by Underwriters Laboratories (UL)
Meets all requirements for UL 1741.
3
RELATED SYSTEM EQUIPMENT
The SunseiTM CC20000D is an integral part of a solar electric power system that includes a
solar panel, a battery and a load.
SOLAR PANELS - (“photovoltaic (PV) array”, “solar modules”):
The SunseiTM CC20000D is compatible with all makes and models of photovoltaic solar
panels.
The entire solar array’s open circuit voltage (Voc) cannot exceed 26 volts (the sum of the Voc
of all solar panels in series). Also, the solar array’s short circuit current (Isc) cannot exceed 20
amps. (This is the sum of the short circuit currents (Isc) of all the solar panels in parallel).
Install all panels with the correct series-parallel configuration to insure proper system voltage
(12 volts) and current.
The SunseiTM CC20000D includes a blocking diode to eliminate leakage of the battery power
into the solar panels at night. No additional protection is needed.
OTHER CHARGING SOURCES: Systems with an additional source of charging (alternator,
battery charger, etc.) can operate with a solar array and a SunseiTM CC20000D. All charging
sources need to connect directly to the battery on independent lines and have their own form
of over-charge protection.
SunseiTM CC20000D FOR NON-SOLAR APPLICATIONS: These units will only operate with
solar electric panels. Do not use to regulate other power sources, such as a hydro or wind
generators/alternators or AC battery chargers. These charging sources can damage the
controller and/or the generating equipment because the SunseiTM CC20000D stops charging
by short-circuiting the input.
BATTERIES: The SunseiTM CC20000D provides the proper charging of standard lead-acid
batteries that are normally used in recreational vehicles, boats and remote stand alone
systems. These include wet cell batteries (with filler caps), sealed, maintenance-free and gelcell batteries. Automobile batteries can also be charged, but these batteries are rarely used as
the primary battery in a solar system. Install all batteries with the correct series-parallel
configuration to insure proper system voltage and current.
SYSTEMS WITH TWO BATTERY BANKS: When solar charging two separate battery banks,
a switch can be installed to allow manual selection of one battery or the other.
BATTERY ISOLATORS: In installations that use a diode battery isolator with two batteries,
the SunseiTM CC20000D needs to connect directly to one of the batteries or an output from
the isolator. The SunseiTM CC20000D will not operate if it is connected to the input of the
isolator.
LOADS: System loads such as lights, radios and DC/AC inverters must be 12 volts DC (unless
an inverter is being used).
4
INSTALLATION
WARNINGS
WARNING: Electricity, even low voltage electricity, can be dangerous. Installation should be
performed by a licensed electrical contractor or other qualified personnel only. The
requirements of National Electrical Codes should be followed.
WARNING: Follow all safety precautions of the battery manufacturer. Proper ventilation must
be provided for the batteries. Most batteries produce hydrogen gas when charging, which is
extremely explosive. Provide adequate battery ventilation. DO NOT expose the battery to
open flame, matches, cigarettes or sparks.
CAUTIONS (The following can cause a fuse to blow and may damage the unit)
CAUTION: DO NOT EXCEED THE UNIT’S VOLTAGE AND CURRENT RATINGS
• Do not exceed the maximum open circuit voltage (voc) rating of 26 volts. This is the sum
of the Voc of all solar panels in series.
•
Do not exceed the maximum current rating 20 amps. This is the sum of the short circuit
currents (Isc) of all the solar panels in parallel.
CAUTION: DO NOT DEVIATE FROM THE RECOMMENDED WIRING INSTRUCTIONS:
• Do not reverse BATTERY (+) and BATTERY (-) connections to the SunseiTM CC20000D.
Any reverse polarity to the battery may damage the unit.
•
Do not reverse the BATTERY and Solar ARRAY connections to the SunseiTM
CC20000D. A battery connected to the array terminals may damage the unit.
•
Do not connect the array directly to the battery when the array is connected to the
SunseiTM CC20000D at the same time. This will cause the fuse to blow when the battery
reaches full charge voltage.
•
Do not wire the SunseiTM CC20000D in such a way that it can be connected to an
alternator (or other charging source) while the battery is disconnected. Other charging
sources should have independent connections to the battery.
•
Do not wire the SunseiTM CC20000D in such a way that it can be connected to a load
without a battery connected. (Example: Do not connect the loads directly to the
SunseiTM CC20000D BATT terminals. This may damage the controller if the battery is
disconnected.)
5
INSTALLATION INSTRUCTIONS
1. MOUNTING CONSIDERATIONS
The SunseiTM CC20000D is designed to be mounted flush against a wall. It can be mounted
onto a wall by adding the optional knockout box (4x7 BOX). Flush mounting or wall
mounting require different installation and mounting considerations.
FLUSH MOUNT: The flush mounted unit requires a rectangular cutout in the mounting
surface with sufficient space (2-3 inches) immediately behind to accommodate the
controller.
WALL MOUNT: The wall-mounted unit (SunseiTM CC20000D with the 4x7 BOX) is
installed onto a wall surface using four mounting screws. Electrical connections are
made through knockouts in the box to the back of the controller. Wiring can be run down
the wall or through a hole in the wall directly below the controller.
2. ACQUIRE TOOLS AND MATERIALS
TOOLS AND MATERIALS NEEDED:
•
•
•
•
•
Slotted screwdriver
Wire cutter/strippers
Keyhole saw or saber saw
Pencil, scratch awl or other marker
Wire of proper gauge to run from the panels, to the SunseiTM CC20000D, to the
battery (See INSTALLATION INSTRUCTIONS 6: WIRE TYPE / SIZE)
• Mounting fasteners of appropriate type for wall material
• Included are four 3/4 - #6 screws and a spare fuse, 25 amp AGC for the SunseiTM
CC20000D
Also for Flush Mounting:
• Drill with 3/32" and 3/8" bits
Also for wall mounting: (SunseiTM CC20000D with 4X7 BOX):
• 1/2 inch Romex strain relief clamps
3. LOCATION
The SunseiTM CC20000D should be mounted where it can be easily seen and reached as
needed. Carefully consider how the wires are to be run from the solar panel to the controller
and from the controller to the battery. The SunseiTM CC20000D should be mounted as close
to the battery as possible, and should be mounted on a vertical surface to aid in cooling.
4. PROTECTION REQUIREMENTS
The unit should be mounted indoors, out of the weather, unless a weatherproof enclosure is
used. Avoid mounting in direct sunlight or in a hot environment or where exposed to
excessive moisture. Locations near refrigerators may pose a moisture problem.
6
INSTALLATION INSTRUCTIONS (continued)
5. PREPARE THE LOCATION PRIOR TO WIRING
FLUSH MOUNT: Use the template provided to position and mark the cutout and the four
mounting holes. Make the cutout using a keyhole or saber saw. Start by drilling holes in the
corners, and then saw between the holes.
WALL MOUNT: Mount the knockout box to the wall using suitable fasteners.
6. SELECT WIRE
WIRE TYPE: When possible, use stranded wire instead of solid wire. Stranded wire does not
fatigue and cause loose connections over time as easily as solid wire. Use red wire for (+)
and black for (-).
WIRE SIZE: Refer to the “WIRE SIZE” chart below to determine the minimum size wire
needed for each connection. Note that the bigger the wire, the lower the AWG. When using
large stranded wire, you may need to divide the ends into two groups and straddle the screw
on the terminal block.
SunseiTM CC20000D: Accepts one wire at 6 AWG (stranded) or two wires at 8 AWG.
Large Wires: To connect large wires to the SunseiTM CC20000D, use crimp connectors or
connect the larger wire to a short, thinner wire using a wire nut (solder these connections).
Wire Size: Minimum wire gauge (AWG) - (based on maximum current)
Battery Connection
Solar Array Connection
Distance round trip (feet/meters)
Model
TM
Sunsei
CC20000D
10’/3m
10
20’/6m
8
30’/9m
6
40’/12m
4*
Distance round trip (feet/meters)
10’/3m
12
20’/6m
10
30’/9m
8
40’/12m
6
* Wire gauge larger than unit can accept directly. See WIRE SIZE / Large Wires above.
7. COMPLETE THE INSTALLATION OF PANELS, BATTERY AND LOAD
Follow the manufacturer's instructions for mounting and wiring the solar panel, batteries and
the load. Install with the correct series-parallel configuration to insure proper system voltage
and current.
8. REMOVE POWER FROM BATTERY / PANELS (if needed)
Before running the wires to the SunseiTM CC20000D be sure that power is disconnected from
the batteries and panels.
9. RUN SYSTEM WIRING
After disconnecting the power sources, run the wires from the battery and solar panel to the
location selected for the controller.
WALL MOUNT: Run the array and battery wires into the box through the knockouts,
using a 1/2 inch Romex cable clamp for strain relief.
7
INSTALLATION INSTRUCTIONS (continued)
10. NOTE WIRE POLARITY
Make sure to correctly mark the polarity of the wires using colored wires or tags. Incorrect
polarity may blow a controller fuse or damage the SunseiTM CC20000D.
CAUTION: Some vehicles or solar kits use black and white wires for connection to the
battery. These kits will label the black wire as battery negative and the white wire as
battery positive (please verify with your manual). Black and red wiring systems will label
the black wire as negative and the red wire as positive. When these systems
interconnect, the black wire does not connect to the black wire.
CAREFULLY NOTE BATTERY POLARITY AND WIRE COLORS!
11. PREPARE WIRES
Using a wire stripper, carefully remove approximately ½ inch of insulation from the
controller end of each wire, being careful not to nick or break any wire strands.
12. SunseiTM CC20000D CONNECTION
Wire the SunseiTM CC20000D according to Figure 1. The wires should be connected
directly to the SunseiTM CC20000D screw terminals (no spade or ring lugs). Tighten
securely.
Any wiring variation can affect the performance and operation of the system.
CAUTION: The two negative connections (ARRAY (-) & BATTERY (-)) must be
separated. Do not install a jumper across the terminal block.
CAUTION: The battery negative connection should not come from a frame or chassis.
This wire needs to originate directly from the battery.
CAUTION: Do not connect any loads to the SunseiTM CC20000D terminals.
13. INSTALL FUSING AS NEEDED
Add circuit protection where needed. A 25 amp fuse and disconnect switch should be
installed on the BATTERY (+) run of the SunseiTM CC20000D.
WARNING: A good system design calls for circuit protection to be added to all wire
runs from the battery. This will provide protection from fire and damage due to overcurrent from the battery. Also, disconnect switches in-line between the components
allow you to isolate power during installation and maintenance. Recommended:
Install properly DC rated, high interrupt, current limiting, over-current protection and
disconnect equipment between the SunseiTM CC20000D and the battery. Refer to the
National Electrical Code or your local alternative energy vendor for
recommendations.
14. SunseiTM CC20000D MOUNTING
Mount the SunseiTM CC20000D to the wall or box front using the four screws provided, or
other suitable fasteners. Do not remove the four rubber spacers, they provide a gap for
added cooling.
8
INSTALLATION INSTRUCTIONS (continued)
15. RECONNECT BATTERY AND ARRAY POWER
16. OPERATION
Operation of the charge controller is now fully automatic. If the battery voltage is below the
Full Charge Termination set-point (14.4 volts) and power is available from the array, the
SunseiTM CC20000D should start up “CHARGING”.
17. CHECK FOR VOLTAGE DROP (OPTIONAL)
Once the system is installed and operational, a check on the connections is recommended.
A poor connection will result in a voltage loss that will distort the battery voltage reading
and cause the charging to stop too soon. To check the onnections, an accurate voltmeter is
required, The SunseiTM CC20000D must be charging with maximum expected charge
current (very sunny conditions).
Battery Connection: First, note the voltage at the battery. Then, immediately note the
voltage at the SunseiTM CC20000D battery terminals. Ideally, the difference in voltage
should be no more than ¼ volt.
Array Connection: Note the voltage at the panel. Then, immediately note the voltage at
the SunseiTM CC20000D Array terminals. Ideally, the difference should be no more than
½ volt.
If the voltage drop is more, suspect crimp connections that have not been soldered, in-line
fuses or fuse holders, or loose terminals. If no location of voltage drop is found, consider
using larger wires (or double up the wires) for your run.
Example: You record these readings:
Battery terminals:
SunseiTM CC20000D battery connection:
13.65 volts
13.95 volts → “.30 volt difference too
large. Decrease voltage drop”
SunseiTM CC20000D panel connection:
Panel(s):
14.10 volts
14.30 volts → “Connection OK”
9
FIGURE 1 Sunsei CC20000D CHARGE CONTROLLER
TM
SOLAR PANEL ARRAY
←
+
+
Batt (-)
Array (-)
LOAD
Array (+)
Batt (+)
A
FUSE RATINGS
A = Fuse / Disconnect switch
SunseiTM CC20000D = 25 amp
B = Rated for load
B
+
BATTERY
FIGURE 2 SunseiTM CC20000D - BACK VIEW
Fuses
TM
Sunsei CC20000D:
Access from rear
Bar-graph selector
For “Bar” readings, place jumper across both
pins.
For “Dot” readings, place jumper across only
one of the pins (“storage position”).
Charge Set-Point Adjust
Adjust the pot here to modify the charge setpoint. Refer to the front display (CHARGE
SET-POINT) to view setting. Turn counterclockwise to increase voltage and clockwise to
decrease voltage.
10
OPERATION
The operation of the SunseiTM CC20000D is completely automatic. This controller will regulate the
charging of batteries during conditions of heavy usage, or when left unattended for long periods of time.
During operation, it is normal for the front plate to feel warm.
CHARGING METHOD – Low Frequency Pulse Width Modulation: The SunseiTM CC20000D
provides pulses of charging current at varying durations to maintain the batteries at a full state of
charge and insure the long-term health on the batteries. The “on” and “off” cycle time is wide
enough to eliminate electronic noise and short enough to insure the batteries are always topped off.
This method allows the batteries to reach a higher voltage with the “on” cycle and protect the
batteries from gassing in the “off” cycle. This will provide the benefits of the higher voltage (reduced
sulfation and stirred up electrolyte) and prevent excessive gassing and excessive water loss.
A TYPICAL DAY: A typical daily cycle will be as follows. As the charging starts for the day and battery
state of charge is low, charging will be continuous and the “CHARGING” light will be on all the time.
As the battery charges up, current will pass into the battery for a while and eventually stop. Later,
charging will resume and the system will continue this cycle throughout the day. During the course
of the day, the duration of the charging period of each cycle will get shorter (cycling on for shorter
periods and staying off longer). When the battery is close to full charge, it will pulse current into the
battery to achieve and maintain full charge. The “CHARGING” light occasionally turning on and off
indicates this pulse charging.
ARRAY AND BATTERY FUSES
ARRAY FUSE: An array fuse is included on the SunseiTM CC20000D. It will protect the controller from
over-current from the solar panels, battery short circuit and incorrect wiring problems with the
system. If the fuse continued to blow after all external problems have been corrected, then this may
indicate a defective unit.
Fuse type: SunseiTM CC20000D: 25 amp AGC
BATTERY FUSE: A battery fuse is included on the SunseiTM CC20000D. This will protect the controller
from over-current from the solar panels, reverse polarity from the batteries and a battery short circuit
and incorrect wiring problem in the system. If the fuse continued to blow after all external problems
have been corrected, then this may indicate a defective unit.
Fuse type: SunseiTM CC20000D: 25 amp AGC.
MAINTENANCE
AVOID DISCONNECTING BATTERY: Do not leave the battery disconnected from the SunseiTM
CC20000D for an extended period of time (weeks or months). If you need to, then disconnect both
battery and array.
RECOMMENDED ANNUAL CARE: Any solar system, when designed correctly, should provide years
of reliable charging with very little user involvement. To assure system reliability, an annual routine
of checking the electrical connections is recommended. Especially on a moving vehicle exposed to
road vibrations. Over time, electrical connections can deteriorate or corrode causing a voltage drop
and possible hot-spots at the problem area.
WHAT TO CHECK: Check to confirm all wire connections are sound and free from corrosion.
Tighten terminal block screws, inspect any fuse connections in-line, the array connections and
battery terminals. Also, consider checking for a voltage drop. See INSTALLATION INSTRUCTIONS
– Step 17: CHECK FOR VOLTAGE DROP ( Page 8).
11
CHARGE SET-POINT ADJUSTMENT
CHARGE SET-POINT ADJUSTMENT SHOULD ONLY BE ATTEMPTED WITH CAUTION.
IMPROPER CALIBRATION CAN RESULT IN BATTERY AND EQUIPMENT DAMAGE.
CAUTION: The standard charging set-points of the SunseiTM CC20000D will be proper for a majority
of the applications; however, the SunseiTM CC20000D allows field adjustment of these set-points.
Caution should be used. It is a common belief that increasing a set-point up will correct an undercharged battery. In fact, this adjustment will not affect the battery level but instead will cause the
battery to overcharge once the sizing problem is corrected. For under-charged batteries, refer to
BATTERY PROBLEMS in the TROUBLESHOOTING section (Page 19).
STANDARD SET-POINT: 14.4 volts for charge termination. Once the charging stops, the voltage will
immediately drop to a lower voltage.
WHEN ADJUSTMENT IS NOT NEEDED:
An adjustment will not make the batteries charge faster.
An adjustment will not increase the output of the panels.
An adjustment will not add more power to a battery that is usually undercharged.
An adjustment is not recommended to correct for a voltage drop in the battery connection.
WHEN ADJUSTMENT IS NEEDED: Adjusting the charge set-points is recommended for certain
situations that might otherwise result in under or overcharging the batteries. These recommendations
are approximate and can be influenced by specific conditions. Contact the battery manufacturer or
supplier to verify proper settings.
SOME BATTERIES REQUIRE DIFFERENT CHARGING VOLTAGES: Sealed, maintenance-free
and gel-cell batteries may require a lower charging voltage. Generally, for these batteries, the
controller should be set for 14.1 to 14.3 volts.
WHEN BATTERY WILL SEE PROLONGED TEMPERATURE EXTREMES: For colder areas
(average temperatures below 50°F (10°C) for many weeks) the set-point should be raised .3 volts
(14.7 volts). For hotter areas (average temperatures above 90° F (32°C) for many weeks) the setpoint should be lowered .3 volts (14.1 volts). Be sure to return to original settings when temperature
moderates.
IN SYSTEMS WITH EITHER EXTREMELY HIGH OR LOW CHARGE RATES: Systems with very
low charge rates (1 amp per 100 amp hour of battery) should have the set-points lowered to about
14.0 to 14.2 volts. Systems with very high charge rates (over 20 amps per 100 amp hours of
battery) should increase the charging set-point to 14.8 to 15.0 volts.
PROCEDURE
1. COMPLETE BATTERY CONNECTION: Connect the battery to the SunseiTM CC20000D according
to the normal installation instructions.
2. SET SWITCH TO “CHARGE SET-POINT”: Slide the front switch to the third position.
3. LOCATE ADJUSTMENT POT: The adjustment pot is located on the backside of the controller on
the circuit board. The adjustment pot appears as a small, square component with a slotted circle in
the middle. (Refer to FIGURE 2 - BACK VIEW) (Page 9).
4. DETERMINE NEW VOLTAGE SET-POINT: Decide on a new voltage termination set-point. Note
that changing the shut-off voltage will also change the "charge resumption" set-point by an equal
amount. If adjusting above 15.0 volts, check to see what the operating limits of other equipment may
be, as some electrical equipment (fluorescent lights, inverter) may be damaged or not operate at
voltages over 15 volts.
12
CHARGE SET-POINT ADJUSTMENT (continued)
5. ADJUST POT: Turning the pot counter-clockwise increases the set-point, clockwise decreases it.
Carefully adjust the pot to change the voltage reading to the desired setting. Do not force the dial
beyond the end stops.
6. MONITOR: After adjustment, monitor the batteries. For unsealed batteries: If you constantly need
to add water, they are set too high. If you do not hear them boil once in a while, they may be too
low.
MONITORING
The system operation can be monitored by the meters and the status lights.
DIGITAL DISPLAY: The Digital display of the SunseiTM CC20000D provides metering of four
parameters, selected by a front panel slide switch.
1st POSITION - "BATTERY VOLTAGE": This displays the battery voltage. The battery voltage is a
general indication of battery condition or capacity. Battery voltage will be higher when the battery is
being charged, with the increase in voltage depending on the amount of charge current. When
charging stops, the voltage will immediately drop down.
For most systems, a fully charged battery that is not being charged or discharged will be at about
12.6-12.8 volts. The normal range of a 12 volt battery is about 11 to 15 volts. A voltage below 11
volts usually indicates a dead battery, and over 15 volts is almost always an over-charged battery. It
is best to keep the batteries above 11.5 volts and below 14.5 volts for maximum battery life and
performance.
2nd POSITION - "ARRAY CURRENT": This displays the amount of current flowing from the solar
panels to the batteries or loads. The solar array current reading can be used to optimize the array tilt
angle by moving the array and noting when current is maximized. Consult the panel supplier or
literature for rated output to see what the output should be for the total number of panels in the
system under ideal conditions. If the charging current seems low, refer to the SOLAR PANEL
PROBLEMS section (Page 18).
3rd POSITION - "CHARGE SET-POINT": This position displays the charge termination voltage setpoint that the controller is currently set to. This setting can be used to verify
the termination set-point or for set-point adjustment. See the CHARGE SET-POINT ADJUSTMENT
section (Page 11).
4th POSITION - "BATTERY VOLTAGE (bar-graph off)": This position is identical to the 1st position
described above except that the battery bar-graph display is turned off. Use this position if current
consumption is a special concern.
“CHARGING” LIGHT: The "CHARGING" light will be on when the battery is charging. When charging,
virtually all the power available from the solar array will pass through to the battery.
“CHARGED” LIGHT: The "CHARGED" light will be on when the battery is fully charged. After the
battery has reached the charge termination voltage, the charging will stop and the “CHARGED” light will
go on. This light will remain on until the battery voltage drops down to the charge resumption voltage.
13
MONITORING (continued)
“BATTERY” CONDITION BAR-GRAPH: This bar-graph provides a general indication of the battery
condition.
The lights will rise and fall as the battery voltage goes up and down. During the day, the battery
voltage can increase and decrease instantly as charging is turned on and off. When the battery is
completely charged, the current will begin to pulse into the battery. This may cause the bar-graph
lights to rise and fall rapidly.
Bar-graph after modifying set-points – The bar-graph provides a general indication of the battery
condition. These lights do not adjust if the charging set-point is modified. When charging batteries
with modified set-points, the terminology and colors may not be appropriate.
Bar-graph “Dot” / Bar-graph “Bar” – The visual appearance of the bar-graph can be adjusted to
meet your individual preference. The bar-graph can be set to use a single light (“Dot”) to represent
the battery condition or it can be set so all the lights below the value are on (“Bar”). The bar-graph
“Dot” will consume less current but the “Bar” setting will be brighter.
To change the “Dot” or “Bar” setting, locate the “BAR-GRAPH MODE” adjustment pins on the
backside of the unit. For “Dot” readings, place jumper across only one of the pins. For “Bar”
readings, place the jumper across both pins.
Red light glow – Occasionally, the very bottom red light may have a slight glow to it. This is not a
problem.
GOOD
Battery can generally be considered “FULL”.
The lights above usually indicate when the unit
is charging.
OK
Battery is less than full. Capacity has dropped
down but voltage is still adequate to provide
power.
LOW
Battery voltage is moderate to low. Use of loads
should be conservative.
VERY LOW
Voltage is very low. Reduce use of loads or use
an additional source to charge the batteries. If
this continues, see the TROUBLESHOOTING
section (Page 14).
14
TROUBLESHOOTING
These sections can assist in the troubleshooting of a solar system.
• Help Notes: Lists some common problems with a solar system.
• SunseiTM CC20000D Problems: If a problem is suspected based on the observations of the
SunseiTM CC20000D controller, find the condition on the SunseiTM CC20000D Problems chart. It
will direct you to a “SunseiTM CC20000D Note” on the next page.
• Fuse Removal Test: Provides a simple test to confirm operation.
• Battery Problems: If you feel your batteries are not being adequately charged or are consistently
being over-charged, refer to the section Battery Problems.
• Solar Panel Problems: If you feel that the solar panels are not performing adequately, refer to the
section Solar Panel Problems.
Help Notes – Normal Conditions and Problem Conditions
Normal Conditions:
1. “ALWAYS CHARGING” or “NEVER CHARGING” - Depending on your system, it may be normal for the
SunseiTM CC20000D to go for long periods of constant charging or long periods with no charging. The
function of the SunseiTM CC20000D is to prevent over-charging of the battery. Therefore, it will charge
continuously when the battery voltage is low and stop all charging as long as the battery voltage is
high.
2. BATTERY WATER LOSS - It is normal for unsealed batteries to need some water from time to time. Minor
water loss is not a problem; just add to the top level when needed. Excessive water loss (a quart or more
in a period of a month) may indicate a more serious problem.
3. BATTERY GASSING - In vented batteries, some gassing is good. Gassing stirs up the battery acid and
allows the battery to fully charge. A little bubbling in the batteries is not necessarily a problem. Refer to
BATTERY WATER LOSS above.
4. TEMPERATURE - Temperature can affect the performance of batteries. They will tend to over-charge easier
when hot, and will not have as much capacity when cold. Temperature can also affect the performance of
the solar panels. The charging current can be substantially higher in cold conditions. When sizing the
system, consider the current at cold conditions. Most panel specifications include a temperature chart.
15
Help Notes (continued)
Problem Conditions:
5. SYSTEM IS NOT SIZED CORRECTLY - The system batteries will tend to be under-charged if the solar
array is too small, if the battery bank is too small, or if the usage is too high. Some systems contain
small hidden loads that can slowly draw down the battery.
6. PROBLEMS WITH SOLAR PANELS - Solar panel output is dependent upon the amount of sun-energy
reaching the panel. This can be seriously affected by the angle of the panel and sun (as in winter months),
minor shading, high level haze (barely visible) and dust on the panel. At the time of installation, a solar
array can have an incorrect series-parallel configuration for the proper system voltage and current. A panel
can
also
become
less
productive
or
defective
over
time.
TEST: Disconnect the SunseiTM CC20000D from the panel, and measure the voltage at panel(+) and
panel(-). In sunny conditions, this should be 18-24 volts. A lower value may indicate a problem with the
panel. To check the panel’s current output, contact a local solar dealer.
7. PROBLEMS WITH BATTERIES - At the time of installation, a battery bank can have an incorrect seriesparallel configuration for the proper system voltage and current. A battery can also go bad and be unable
to maintain a charge. If the battery is going bad, a little charging or discharging will cause a large change
in the battery voltage. Also, a shorted battery cell will cause the battery to gas heavily and the system will
charge constantly will no notable increase in voltage. If the condition of the battery is suspect, a battery
capacity test is recommended.
8. BAD CONNECTION: PANEL - The solar panel connection to the controller may be weak or completely
out. Problems can be found at the SunseiTM CC20000D connection (ARRAY (+) & ARRAY (–)
terminals), both panel connections (“+” or “–”), the Array Fuse on SunseiTM CC20000D (either blown or
defective), or fuses and unsoldered crimp connectors in these lines. Also, wire that is too small for the
length of the run may cause a problem. Refer to INSTALLATION INSTRUCTIONS – Step 17: CHECK
FOR VOLTAGE DROP (Page 8).
9. BAD CONNECTION: BATTERIES - The battery connection to the controller may be weak or completely
out. The SunseiTM CC20000D needs to read an accurate battery voltage to regulate the charging
correctly. Therefore, you need to minimize the voltage drop from the battery. Problems can be found
with the SunseiTM CC20000D connection (BATT (+) and BATT (–) terminals), both battery terminals (“+”
or “–”), the Battery Fuse on SunseiTM CC20000D (either blown or defective), or fuses and unsoldered
crimp connectors in these lines. Also, small wire or incorrect wiring may cause a voltage drop. Refer to
INSTALLATION INSTRUCTIONS – Step 12: SunseiTM CC20000D CONNECTION (Page 7) and Step 17:
CHECK FOR VOLTAGE DROP (Page 8).
10. CONTROLLER MISWIRED - This may include reversing the polarity from the panels or batteries, or
switching the array and battery connections. This may also include a deviation from the wiring
instructions, such as using a jumper across the BATTERY(-) & ARRAY(-) connections or by having your
battery(–) connection run to a frame or chassis and not the actual battery itself. Refer to INSTALLATION
INSTRUCTIONS – Step 12: SunseiTM CC20000D CONNECTION (Page 7).
11. INCORRECT VOLTAGE SET-POINT - The SunseiTM CC20000D may be functional but the charge
termination set-point may not be correct for your batteries. The factory set-point is 14.4 volts and is
designed to work for the majority of batteries. Set the front panel switch position to “CHARGE SETPOINT” and verify set-point. Refer to the CHARGE SET-POINT ADJUSTMENT section (Page 11) and
consider if an adjustment may be necessary.
12. SYSTEM NOISE - The SunseiTM CC20000D can be affected by electrical noise from a converter or
inverter. This will not affect the charging function but will cause erratic meter readings. If the SunseiTM
CC20000D is connected to a bus that is connected to a converter, try connecting the SunseiTM
CC20000D directly to the battery instead.
13. CONTROLLER DEFECTIVE - The SunseiTM CC20000D may no longer be functional. A defective unit
can overcharge the battery or stop all charging. A faulty unit can not drain a battery. It may have been
exposed to high voltage or current, reverse polarity from the batteries or other wiring problem.
16
SunseiTM CC20000D Problems: Refer to this chart and the SOLAR PANEL PROBLEMS
section (Page 18) to help diagnose problems based on the SunseiTM CC20000D readings.
CASE
1→
2→
3→
4→
5→
6→
7→
8→
9→
10 →
BATTERY
VOLTAGE
READING
Display blank
ARRAY
CURRENT
READING
Display blank
Display blank
Display blank
10-13
00.0
OFF
12.0-14.7
00.0
ON
13-14.7
00.0
ON
14.7 - 22.0
YELLOW
GREEN
CHARGING CHARGED
LIGHT
LIGHT
ON
Night only
See Note 2
Day
See Note 3
Day
See Note 4
Day
See Note 5
ON
See Note 6
ON at night
Reading
changing
rapidly
Bad display
readings
Voltage reading
higher than
actual battery
voltage
Day
SunseiTM
CC20000D
NOTE
See Note 1
OTHER
Reading
changing
rapidly
Bad display
readings
May be
flashing
May be
flashing
Night
See Note 7
Day
See Note 8
See Note 9
See Note 10
Day
See Note 11
Day – When fuse is
touched
See Note 12
13 →
Day –SunseiTM
CC20000D buzzing
See Note 13
14 →
15 →
16 →
SunseiTM CC20000D hot
See Note 14
Bar-Graph off
See Note 15
Fuse keeps blowing
See Note 16
11 →
12 →
Current less
than expected
Changes to
ON or OFF
Changes to
ON or OFF
SunseiTM CC20000D PROBLEM NOTES (from SunseiTM CC20000D PROBLEMS chart)
Note 1 - A display blank both day and night may indicate…
• A bad connection exists to the solar panel (See BAD CONNECTION: PANEL (Help Note 8)) and the battery has
either a bad connection (See BAD CONNECTION: BATTERY (Help Note 9)) or the battery is low in voltage (the
meter requires 10 volts to operate).
• The SunseiTM CC20000D is defective. See CONTROLLER DEFECTIVE (Help Note 13).
Note 2: - A display that is only blank at night may indicate…
• A bad connection exists to the battery. See BAD CONNECTION: BATTERY (Help Note 9).
• A blocking diode or diode isolator exists in the battery connection. If there is a blocking diode, remove it.
If there is a diode isolator, modify the system so the SunseiTM CC20000D charges only one battery bank.
Note 3 - A low voltage condition with no daytime charging may indicate…
• The system has no panel input. See BAD CONNECTION: PANEL (Help Note 8)
• The charge set-point has been set very low. See INCORRECT VOLTAGE SET-POINT (Help Note 11)
• The SunseiTM CC20000D is defective. See CONTROLLER DEFECTIVE (Help Note 13).
TEST: Perform the BATTERY FUSE REMOVAL TEST (Page 18)
Note 4 - The “CHARGING” and “CHARGED” lights on is caused by a bad battery connection. See BAD CONNECTION:
BATTERY (Help Note 9).
17
SunseiTM CC20000D PROBLEM NOTES ( continued )
Note 5 - The “CHARGING” light on with 00.0 amps from the array may indicate…
• A condition exists of very low levels of light to the panels
• A system problem. This would be a panel, connection or wiring problem. Often, this happens when the negative
connections from the array and battery are connected. Refer to INSTALLATION INSTRUCTIONS – Step 12:
SunseiTM CC20000D CONNECTION (Page 7).
• The SunseiTM CC20000D is defective. See CONTROLLER DEFECTIVE (Help Note 13).
TEST: Perform the BATTERY FUSE REMOVAL TEST (Page 18)
Note 6 - High voltage with the “CHARGING” light on may indicate…
• A bad connection exists to the battery. See BAD CONNECTION: BATTERY (Help Note 9).
• The charge set-point is set very high. See INCORRECT VOLTAGE SET-POINT (Help Note 11)
• The SunseiTM CC20000D is defective. See CONTROLLER DEFECTIVE (Help Note 13).
TEST: Perform the BATTERY FUSE REMOVAL TEST. (Page 18)
Note 7 - The "CHARGING" light can be on (bright to dim) at night if the panels are under even very low levels of
light (moonlight or street lights). The "CHARGING" light on brightly at night may also indicate…
• The unit is mis-wired. Refer to INSTALLATION INSTRUCTIONS – Step 12: SunseiTM CC20000D CONNECTION
(Page 7).
• There is a blocking diode located within the solar panels or in the panel connection. This is not a serious problem, but
should be removed if possible.
• The SunseiTM CC20000D is defective. See CONTROLLER DEFECTIVE (Help Note 13).
TEST: Disconnect the panel (ARRAY (+)), if the light goes off, then it may be possible that the panel is receiving
enough light for a slight charge, or a diode exists in the connection.
Note 8 – The display readings and status lights changing rapidly may indicate…
• A normal condition. If the battery is fully charged and the array has a lot of additional charge current, the controller
can pulse on and off rapidly, especially when current is being used by a load. This is OK.
• A bad connection exists to the battery. See BAD CONNECTION: BATTERY (Help Note 9).
• A problem exists with the battery. The battery bank is bad or too small. See PROBLEMS WITH BATTERIES (Help
Note 7)
TEST: Take an accurate voltage reading at the battery. If this voltage reading stays steady while the reading on the
SunseiTM CC20000D goes up and down, then suspect a bad battery connection. If the voltage here also moves up
and down rapidly, this would indicate either a normal condition or a battery problem.
Note 9 - A bad display readings may indicate…(display issues don’t affect the charging functions)
• System noise. Digits is OK, but the readouts are erratic. See SYSTEM NOISE (Help Note 12)
• A Defective unit. Digits is OK, erratic readouts and a correlation to high humidity exists.
• A Defective unit. If the quality of the digits are bad with missing segments or black background areas.
Note 10 - A voltage reading that is a lot higher than the actual battery voltage is caused by a bad battery
connection. Somewhere it could be corroded or loose. If you recheck at night or disconnect the panel, the
difference should go away. See BAD CONNECTION: BATTERY (Help Note 9).
Note 11 - If the charge current seems too low for your panels, refer to the SOLAR PANEL PROBLEMS section
(Page 18). Also, check to see that there is not an alternative path from the solar panel negative to the battery
negative other than through the SunseiTM CC20000D.
Note 12 - The charge control circuit will reset when power is removed. Touching or removing the battery fuse will
momentarily lose power to the control circuit, causing it to reset. It will usually reset “CHARGING”. This is normal and
does not indicate a problem.
Note 13 - The buzzing sound is caused by the controller rapidly switching on and off and is the result of a bad
battery connection. See BAD CONNECTION: BATTERY (Help Note 9).
Note 14 - The SunseiTM CC20000D may get warm during normal operation. When operating near maximum ratings, the
front plate gets very warm. If the unit should get too hot to touch, it may be defective. See CONTROLLER
DEFECTIVE (Help Note 13).
Note 15 – If the bar-graph goes off, confirm that the slide switch is set to the top position. Also, look at the battery
voltage. If it is below 10.5 volts, the bar-graph will not light.
Note 16 – If the fuses continuously blow, refer to the ARRAY & BATTERY FUSE section (Page 10).
18
Fuse Removal Test: (checks operation)
This test temporarily removes the battery connection to the SunseiTM CC20000D. The new voltage display will
indicate if the unit is working properly. Note: when the fuse is removed, it is normal for the front lights to both
go on and to hear a faint buzzing. Remember to replace the fuse immediately after testing.
Procedure: During a sunny period when the battery voltage is over 10 volts, remove the BATTERY fuse. Note the
"BATTERY VOLTAGE" reading. Compare the reading to the options below.
• VOLTAGE READS FROM 10.0 TO 15.0 VOLTS - If the new reading is in this range, perform another step. Note
the exact voltage value. Replace the fuse. Now, again note the value. Did the value change ?
• VOLTAGE: 10 - 15V. AND CHANGES WITH FUSE REMOVAL - This is the correct reaction and the unit is
working properly.
• VOLTAGE: 10 - 15V. AND READING DOES NOT CHANGE WITH FUSE REMOVAL - If the meter stays the
same before and after removing the fuse, this indicates the SunseiTM CC20000D may not be connected to the
battery. See BAD CONNECTION: BATTERY (Help Note 9).
• BATTERY VOLTAGE READING IS BLANK - If the meter is blank, this means that the solar array is bad or
disconnected or that the SunseiTM CC20000D is defective. If possible, perform this step. Disconnect the array(+)
connection at the SunseiTM CC20000D. With a volt meter, measure the voltage of the array by measuring the
array wires where they meet the SunseiTM CC20000D.
• VOLTAGE DISPLAY BLANK AND ARRAY VOLTAGE AT SunseiTM CC20000D IS ZERO - This indicates that
there is a problem with the array or array connection. See PROBLEMS WITH SOLAR PANELS (Help Note
6) and BAD CONNECTION: PANEL (Help Note 8).
• VOLTAGE DISPLAY BLANK AND ARRAY VOLTAGE GREATER THAN 16V. - This indicates that the array is
OK but the SunseiTM CC20000D has a bad ARRAY fuse or the SunseiTM CC20000D is defective. See
CONTROLLER DEFECTIVE (Help Note 13).
• VOLTAGE READING IS GREATER THAN 16.0 VOLTS - This would indicate that the SunseiTM CC20000D is
defective. The meter is displaying the panel voltage, which is usually about 16-22 volts. See CONTROLLER
DEFECTIVE (Help Note 13).
Solar Panel Problems: Refer to this section to help diagnose problems based on panel
performance.
CASE PANELS
1→
2→
Less charge current than expected
Less voltage than expected
SEE NOTE(S)
See Panel Note 1
See Panel Note 2
Panel Note 1 - The panels should generate a charge close to their rated short circuit current as presented in their
specifications. To reach this level assumes that all conditions are ideal. If the panel performance as measured
on the SunseiTM CC20000D controller is much lower, consider the following:
• Solar Panels Problem - Panels are dirty, not aligned or other problem. See if the "ARRAY CURRENT" reading
improves after cleaning the panels and adjusting their orientation. Locate the panel where no shadows will cross
it. See PROBLEMS WITH SOLAR PANELS (Help Note 6).
• Bad Connection to the Solar Panel - See BAD CONNECTION: PANEL (Help Note 8).
• Temperature Issues – Panel performance varies with temperature (better when cold). See TEMPERATURE
(Help Note 4 )
Panel Note 2 - Ideally, a disconnected solar panel should measure 18-24 volts. A lower voltage, under ideal
conditions, may indicate a defective panel. See PROBLEMS WITH SOLAR PANELS (Help Note 6). Once a
solar panel is connected to a battery, the panel voltage will immediately drop down to match the battery voltage.
This is normal.
19
Battery Problems: Refer to this section to help diagnose problems based on battery
observations.
CASE BATTERY
1→
2→
Seems to be over-charging
Does not fully charge batteries (or)
Does not hold a charge
SEE NOTE(S)
See Battery Note 1
See Battery Note 2
Battery Note 1 - BATTERY OVER-CHARGING: If there is evidence that the batteries have been over-charging,
consider the following:
• Normal Battery Condition: The batteries may not be over-charging but only be experiencing normal water loss
and normal levels of gassing. Check the “BATTERY VOLTAGE” reading. Normal battery voltage for a wet cell
battery can be up to 14.6 volts. See BATTERY WATER LOSS and GASSING (Help Notes 2 and 3)
• Controller Problem: The SunseiTM CC20000D could be defective. Perform the FUSE REMOVAL TEST (Page
18). Determine if the SunseiTM CC20000D is working properly. Check for INCORRECT VOLTAGE SET-POINT
(Help Note 11)
• Batteries Need Lower Set-point: The batteries may require a lower full-charge voltage. Refer to INCORRECT
VOLTAGE SET-POINT (Help Note 11).
• Other Charging Sources: Another charging source could be the cause. If the SunseiTM CC20000D is not
charging, the overcharging may be from another source. Some 110 volt battery chargers are not well regulated
and could over-charge batteries if left unattended.
• A Hot Battery - Hot temperatures can affect the battery charging. A hot location for batteries will tend to overcharge the batteries. See TEMPERATURE (Help Note 4).
Battery Note 2 - BATTERY UNDER-CHARGED: If the battery voltage is often low or the battery voltage drops fast
after charging, consider the following:
• System not sized correctly - See Help Note 5. For too much usage, try charging the battery with another
charging source (engine alternator, generator or AC battery charger). If the batteries charge okay and hold the
charge, an increase in the number batteries and panels may be needed to support the usage.
• Solar Panels Problem - Panel may be dirty, not aligned or other problem. See PROBLEMS WITH SOLAR
PANELS (Help Note 6)
• Bad Connection – A bad connection can reduce the charge. See BAD CONNECTION: PANEL and
BATTERIES (Help Notes 8 & 9)
• SunseiTM CC20000D Controller Problem - Perform the FUSE REMOVAL TEST (Page 18). Also, refer to the
SunseiTM CC20000D PROBLEM section. Examine the readings from the SunseiTM CC20000D meter to see if
they indicate a problem.
• A Bad Battery - The batteries may be going bad. See PROBLEMS WITH BATTERIES (Help Note 7).
• A Cold Battery - Cold temperatures can affect the battery charging. If the battery is cold much of the time, the
battery’s long-term performance and life may suffer. See TEMPERATURE (Help Note 4).
LIMITED TWO-YEAR WARRANTY
(Warranty terms effective as of October 1, 2005)
1. ICP Solar Technologies warrants all its products for a period of two (2) years from the date of shipment from its factory. This
warranty is valid against defects in materials and workmanship for the two (2) year warranty period. It is not valid against
defects resulting from, but not limited to:
a. Misuse and/or abuse, neglect or accident.
b. Exceeding the unit's design limits.
c. Improper installation, including, but not limited to, improper environmental protection and improper hook-up.
d. Acts of God, including lightning, floods, earthquakes, fire and high winds.
e. Damage in handling, including damage encountered during shipment.
2. This warranty shall be considered void if the warranted product is in anyway opened or altered. The warranty will be void if
any eyelet, rivets, or other fasteners used to seal the unit are removed or altered, or if the unit's serial number is in any way
removed, altered, replaced, defaced or rendered illegible.
3. The two (2) year term of this warranty does not apply to equipment where another manufacturers' warranty is available. An
example of such equipment may be, but is not limited to, an electronic enclosure. The time limit for this warranty may be for
less than the ICP Solar limited warranty. ICP Solar will assist the claimant in attempts to seek warranty claims for such
equipment, where appropriate.
4. ICP Solar cannot assume responsibility for any damages to any system components used in conjunction with ICP Solar
products, nor for claims for personal injury or property damage resulting from the use of ICP Solar products, the improper
operation thereof, or consequential damages arising from the products or use of the products.
5. ICP Solar cannot guarantee compatibility of its products with other components used in conjunction with ICP Solar products
including, but not limited to, solar controllers, batteries and system interconnects, and such loads as inverters, transmitters
and other loads that produce "noise" or electromagnetic interference, in excess of the levels to which ICP Solar products are
compatible.
6. Warranty repair and/or evaluation will be provided only at the Montreal, Canada facility of ICP Solar. Units for such repair
and/or evaluation must be returned freight prepaid to ICP Solar with a written description of any apparent defects. ICP Solar
will not be required at any time to visit the installation site wherein its products are subject to warranty repair and/or
evaluation.
7. Only ICP Solar is authorized to repair any of its products, and reserves the right to repair or replace any unit returned for
warranty repair. The party returning a unit for repair is responsible for proper packaging and for shipping and insurance
charges, as well as any other charges encountered in shipping to and from ICP Solar.
8. This warranty supersedes all other warranties and may only be modified by statement, in writing, signed by ICP Solar.
WARRANTY SERVICE
Register your warranty online at www.icpsolar.com/warranty
and enter to win an ICP Solar product.
If warranty service is required, please contact the dealer or distributor who sold you the controller.
For further assistance, contact ICP Solar customer service at [email protected].
Please note that ICP Solar will not accept returns without prior authorization. The original proof
of purchase is required for warranty validation.
SunseiTM is a trademark of ICP Solar Technologies Inc.

advertisement

Key Features

  • Over 95% charging efficiency
  • High voltage shut-off protection
  • Digital voltage and current readout
  • Adjustable charge set-point
  • Reverse leakage protection
  • Mounting flexibility
  • Compatible with most batteries and solar panels

Frequently Answers and Questions

What types of batteries are compatible with the Sunsei CC20000D?
This charge controller is compatible with most battery types, including wet cell, sealed, maintenance-free, and gel-cell batteries.
Can I adjust the charge set-point of the Sunsei CC20000D?
Yes, the Sunsei CC20000D allows field adjustment of the charge set-point, which can be modified to suit specific battery types or environmental conditions.
How do I know if the Sunsei CC20000D is working properly?
You can monitor the system's operation using the digital display and status lights. The 'CHARGING' light indicates charging, while the 'CHARGED' light indicates full charge.

Related manuals

Download PDF

advertisement