Honda 08V31-TE0-100A Installation Instructions Manual

www.collegehillshonda.com
INSTALLATION
INSTRUCTIONS
Accessory
Application
FOG LIGHTS
P/N 08V31-TE0-100A
2012 ACCORD
2-DOOR
EX, EX-L
Publications No.
AII 46516
Issue Date
AUG 2011
PARTS LIST
Left fog light
Lighting switch
2
Self-tapping screws
2
Clips
Right fog light
2
Fog light cords
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Diagonal cutters
Ratchet
2
Fog light harnesses
10 mm Socket
10 mm Open end wrench
Tape
Trim Tool Set (T/N SOJATP2014)
Blanket
Illustration of the Fog Lights Installed on the Vehicle
4
Wire ties
2
Wire ties with clips
LIGHTING
SWITCH
Ground bolt
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
RIGHT
FOG LIGHT
AII 46516 (1108)
021501AX
FOG LIGHT LEFT
FOG LIGHT
HARNESS
FOG
LIGHT
HARNESS
08V31-TE0-1A00-90
1 of 10
www.collegehillshonda.com
INSTALLATION
4.
Customer Information: The information in this
installation instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
1.
Make sure you have the anti-theft code for the audio
and navigation system (if equipped).
2.
Disconnect the negative cable from the battery.
Attach tape to the front bumper as shown.
8 RETAINING
TABS
FLAT-TIP
SCREWDRIVER
2 SELF-TAPPING
SCREWS
3 RETAINING
TABS
TAPE
Removing Parts (Vehicle Exterior)
3.
Remove the front bulkhead cover (seven clips).
7 CLIPS
FRONT
BULKHEAD
COVER
3 RETAINING
TABS
10 CLIPS
FRONT BUMPER
TAPE
021503AX
5.
Remove two self-tapping screws and ten clips.
6.
Remove the front bumper (fourteen retaining tabs).
NOTE: Have an assistant help you when removing
the front bumper. Place the front bumper on a
blanket after removal.
AII 46516 (1108)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
FRONT BUMPER
021502AX
2 of 10
www.collegehillshonda.com
Routing the Fog Light Harness
7.
8.
On the passenger’s side of the vehicle, locate the
1-pin connecter blue taped to the vehicle harness.
Remove the tape to release the connector.
Plug the fog light harness 1-pin connector into the
vehicle harness 1-pin connector.
VEHICLE HARNESS
1-PIN CONNECTOR
1-PIN
CONNECTOR
VEHICLE
HARNESS
VEHICLE HARNESS
1-PIN CONNECTOR
FOG LIGHT
HARNESS
BLUE TAPE
Remove.
RIGHT HEADLIGHT
732008DY
730105BE
9.
Secure one wire tie with clip to the fog light harness
at the green tape. Secure the wire tie with clip to the
hole in the vehicle frame.
RIGHT
HEADLIGHT
GREEN
TAPE
WIRE TIE WITH CLIP
FOG LIGHT
HARNESS
FOG LIGHT
HARNESS
VEHICLE FRAME
771015AB
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 46516 (1108)
3 of 10
www.collegehillshonda.com
10. Secure the 1-pin connector to the vehicle harness
with a wire tie. Secure the fog light harness to the
vehicle harness with a wire tie at the green tape.
VEHICLE
HARNESS
2 WIRE
TIES
GREEN
TAPE
12. On the driver’s side of the vehicle, locate the vehicle
harness 1-pin connector. Plug the fog light harness
1-pin connector to the vehicle harness 1-pin
connector.
FOG LIGHT
HARNESS
FOG LIGHT HARNESS
1-PIN CONNECTOR
LEFT
HEADLIGHT
VEHICLE HARNESS
1-PIN CONNECTOR
VEHICLE
HARNESS
RIGHT
HEADLIGHT
FOG LIGHT
HARNESS
732004CY
13. Secure one wire tie with clip to the fog light harness
at the green tape. Secure the wire tie with clip to the
hole in the vehicle frame.
FOG LIGHT
HARNESS
772002AB
WIRE TIE
WITH CLIP
GREEN
TAPE
11. Secure the fog light harness ground terminal to the
vehicle frame with the supplied ground bolt.
FOG LIGHT
HARNESS
RIGHT
HEADLIGHT
LEFT
HEADLIGHT
VEHICLE
HARNESS
VEHICLE
GROUND BOLT
Do not use.
FOG LIGHT
HARNESS
VEHICLE FRAME
FOG LIGHT
HARNESS
732005BY
VEHICLE
FOG LIGHT HARNESS FRAME
GROUND TERMINAL
GROUND
BOLT
4 of 10
771017AB
AII 46516 (1108)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
14. Near the 1-pin connector, secure the fog light
harness to the vehicle harness with one wire tie at
the green tape.
GREEN
TAPE
WIRE TIE
Installing the Fog Lights
17. Secure three clips on the fog light cord to the left fog
light.
3 CLIPS
LEFT
HEADLIGHT
FOG LIGHT
HARNESS
VEHICLE
HARNESS
FOG LIGHT
HARNESS
FOG LIGHT
CORD
LEFT
FOG LIGHT
021505AX
732006BY
15. Locate and remove the vehicle ground bolt. Secure
the fog light harness ground terminal and vehicle
ground terminal to the vehicle frame with the vehicle
ground bolt just removed.
18. Plug the fog light cord 2-pin connector into the left
fog light.
LEFT
FOG LIGHT
FOG LIGHT
CORD
WIRE TIE
VEHICLE
HARNESS
FOG LIGHT
HARNESS
LEFT
HEADLIGHT
LEFT
FOG LIGHT
VEHICLE
GROUND
BOLT
FOG LIGHT
CORD 2-PIN
CONNECTOR
FOG LIGHT
CORD 2-PIN
CONNECTOR
BRACKET
021506AX
19. Secure the fog light cord 2-pin connector to the
bracket.
FOG LIGHT HARNESS
GROUND TERMINAL
732007BY
VEHICLE GROUND
TERMINAL
16. Near the ground terminal, secure the fog light
harness to the vehicle harness with one wire tie.
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 46516 (1108)
5 of 10
www.collegehillshonda.com
20. Remove the left fog light cover (three self-tapping
screws).
24. Plug the fog light harness connectors into the fog
lights.
FRONT
BUMPER
FOG LIGHT HARNESS
CONNECTOR
FOG LIGHT HARNESS
CONNECTOR
RIGHT
FOG LIGHT
LEFT FOG
LIGHT COVER
3 SELF-TAPPING
SCREWS
Reuse.
FRONT
BUMPER
021504AX
021602AX
25. Reinstall the front bumper.
NOTE: Have an assistant help you when installing
the front bumper.
21. Install one clip to the front bumper.
FRONT BUMPER
LEFT
FOG LIGHT
FRONT BUMPER
CLIP
LEFT
FOG LIGHT
3 SELF-TAPPING
SCREWS
Reuse.
SELF-TAPPING
SCREW
021601AX
22. Install the left fog light to the front bumper with one
self-tapping screw and three self-tapping screws
removed in step 20.
23. Repeat steps 17 through 22 to install the right fog
light.
6 of 10
AII 46516 (1108)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
Installing the Lighting Switch
26. Lower the tilt lever and pull the steering wheel out.
28. Remove the lower steering column cover (three
screws). The upper screws are self-tapping screws.
2 RETAINING TABS
Push.
LOWER
STEERING
COLUMN
COVER
UPPER
STEERING
COLUMN
COVER
2 HOOKS
2 SELF-TAPPING
SCREWS
LOWER
STEERING
COLUMN
COVER
SCREW
29. Turn the steering wheel 90° counterclockwise, and
unplug the vehicle connector from the lighting
switch.
TILT LEVER
RETAINING
TAB
COLUMN
GUIDE
FLAT-TIP
SCREWDRIVER
7111090Y
VEHICLE
CONNECTOR
HOLDER
VEHICLE
CONNECTOR
6608050T
27. Remove the upper steering column cover:
•
•
Insert a flat-tip screwdriver along the column
guide inside the lower cover, and gently pry out
on the retaining tab on the upper column cover.
LIGHTING
SWITCH
Push the lower cover to release two retaining
tabs, and pull up on the upper cover to release
two hooks.
LIGHTING
SWITCH
STEERING
WHEEL
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 46516 (1108)
6303180B
7 of 10
www.collegehillshonda.com
30. Remove two self-tapping screws from the lighting
switch. While pushing the retaining tab, slide the
lighting switch out of the bracket, and remove it from
the steering column. Do not pull on the lever when
removing the switch. Do not damage the tab hole in
the steering column.
32. Plug the vehicle connector into the new lighting
switch.
VEHICLE
CONNECTOR
HOLDER
VEHICLE
CONNECTOR
STEERING
COLUMN
TAB
HOLE
NEW
LIGHTING
SWITCH
CASE
NEW
LIGHTING
SWITCH
RETAINING
TAB
LEVER
6303210B
2 SELF-TAPPING
SCREWS
LIGHTING
SWITCH
7109010E
31. Install the new lighting switch into the steering
column. Install the two self-tapping screws. Do not
push on the lever when installing the case. Push the
case into the bracket and set the retaining tab into
the tab hole.
33. Check that all wire harnesses are routed properly
and all connectors are plugged in.
34. Reinstall all removed parts.
35. Reconnect the negative cable to the battery.
36. Enter the anti-theft codes for the customer’s audio
and navigation system if equipped, and reset the
radio station presets.
37. Reset the clock.
TAB
HOLE
STEERING
COLUMN
CASE
RETAINING
TAB
LEVER
8 of 10
NEW LIGHTING
SWITCH
2 SELF-TAPPING
SCREWS
7109020E
AII 46516 (1108)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
USE AND CARE
Fog Light Aiming Adjustment
How to Operate the Fog Lights
38. Adjust the fog lights:
• Turn the headlight switch to the “
(headlights on low beam).
” position
• Turn the fog light switch on (indicator is on).
• If the fog lights do not turn on, check the fuse and all the
connectors, including the ground cable.
•
Adjust the aim according to local laws and
regulations.
•
To adjust, turn the aiming adjustment knob in or
out until the correct aim is obtained.
AIMING ADJUSTMENT
KNOB
HEADLIGHT SWITCH
AUTO/
FOG LIGHT
SWITCH
OFF
Low High
OFF
-
-
-
-
ON
-
-
ON
-
To lower.
To raise.
021603AX
922602AG
NOTE: The fog light lenses can cloud when the outside
temperature is cold; this is normal and should go away in
warm weather.
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 46516 (1108)
9 of 10
www.collegehillshonda.com
BULB REPLACEMENT
1.
3.
Turn the steering wheel counterclockwise. Remove
two clips, and pull down the inner fender.
INNER FENDER
Install the new bulb and socket into the fog light.
•
Use only a genuine Honda halogen light bulb of
specified wattage.
Rating: 12V 55W H11 Halogen Light Bulb
P/N33165-S5A-003
•
Do not touch the bulb. Oily or greasy substances
on the bulb can shorten its service life due to the
heat produced when the bulb is turned on. If the
bulb is accidentally touched, wipe it clean with a
soft cloth that has been dampened with a
denatured alcohol or a mild detergent solution.
•
When installing the new bulb, align the cutout on
the fog light with the tab on the new bulb and turn
the new bulb clockwise until it locks. If not
properly aligned, the fog light may affect the
oncoming driver’s view.
Turn.
2-PIN
CONNECTOR
NEW BULB
CLIP
730111AE
2.
Insert your hand inside of the inner fender pulled
down in step 1. Unplug the connector from the fog
light, and remove the bulb by turning it
counterclockwise.
FOG LIGHT
NEW BULB
021605AX
4.
Reinstall the removed parts. Check that the wire
harnesses are not pinched. Be sure to install the
clips securely.
5.
Check the operation of the fog lights; adjust the aim
if necessary.
AII 46516 (1108)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
BULB
FOG LIGHT
2-PIN
CONNECTOR
021604AX
10 of 10