iDataLink maestro Rr Install Manual

SELECT VEHICLE
PRINT PAGES NEEDED
HOW TO USE THIS INSTALL GUIDE
1
Open the Bookmarks menu and find your vehicle OR scroll
down until you find the install guide for your vehicle.
2
Print only the pages for your vehicle using the advanced
options in the Print menu.
3
Install your Maestro RR according to the guide for your vehicle.
WARNING
Pressing the printer icon or “quick printing” this document will print
all of the guides in this compilation.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in
are the properties of their respective owners.
INSTALL GUIDE
2020
Toyota 4 Runner
With JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota 4 Runner With JBL 2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota 4 Runner With JBL 2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
1
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota 4 Runner With JBL 2020
WIRING DIAGRAM with JBL
STEP 3
STEP 1
RCA CABLES
WHITE
WHITE/BLACK
GRAY
GRAY/BLACK
LF RCA INPUT
RF RCA INPUT
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
CONNECTIONS
NOT
REQUIRED
WITH AMP
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
CONNECT
IF
THERE IS
A MATCH
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota 4 Runner With JBL 2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2020
Toyota 4 Runner
Without JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota 4 Runner Without JBL 2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota 4 Runner Without JBL 2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota 4 Runner Without JBL 2020
WIRING DIAGRAM without JBL
STEP 3
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
CONNECT
IF
THERE IS
A MATCH
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota 4 Runner Without JBL 2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2019-2020
Toyota Avalon
With JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota Avalon With JBL 2019-2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota Avalon With JBL 2019-2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
1
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota Avalon With JBL 2019-2020
WIRING DIAGRAM with JBL
STEP 3
STEP 1
RCA CABLES
WHITE
WHITE/BLACK
GRAY
GRAY/BLACK
LF RCA INPUT
RF RCA INPUT
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
CONNECTIONS
NOT
REQUIRED
WITH AMP
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
CONNECT
IF
THERE IS
A MATCH
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota Avalon With JBL 2019-2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2019-2020
Toyota Avalon
Without JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota Avalon Without JBL 2019-2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota Avalon Without JBL 2019-2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota Avalon Without JBL 2019-2020
WIRING DIAGRAM without JBL
STEP 3
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
CONNECT
IF
THERE IS
A MATCH
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota Avalon Without JBL 2019-2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2018
Toyota C-HR
With CarPlay With JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota C-HR With CarPlay With JBL 2018
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota C-HR With CarPlay With JBL 2018
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
1
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota C-HR With CarPlay With JBL 2018
WIRING DIAGRAM with JBL
STEP 3
STEP 1
RCA CABLES
WHITE
WHITE/BLACK
GRAY
GRAY/BLACK
LF RCA INPUT
RF RCA INPUT
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
CONNECTIONS
NOT
REQUIRED
WITH AMP
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
CONNECT
IF
THERE IS
A MATCH
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota C-HR With CarPlay With JBL 2018
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2018
Toyota C-HR
With CarPlay Without JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota C-HR With CarPlay Without JBL 2018
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota C-HR With CarPlay Without JBL 2018
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota C-HR With CarPlay Without JBL 2018
WIRING DIAGRAM without JBL
STEP 3
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
CONNECT
IF
THERE IS
A MATCH
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota C-HR With CarPlay Without JBL 2018
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2019-2020
Toyota C-HR
With JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota C-HR With JBL 2019-2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota C-HR With JBL 2019-2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
1
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota C-HR With JBL 2019-2020
WIRING DIAGRAM with JBL
STEP 3
STEP 1
RCA CABLES
WHITE
WHITE/BLACK
GRAY
GRAY/BLACK
LF RCA INPUT
RF RCA INPUT
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
CONNECTIONS
NOT
REQUIRED
WITH AMP
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
CONNECT
IF
THERE IS
A MATCH
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota C-HR With JBL 2019-2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2019-2020
Toyota C-HR
Without JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota C-HR Without JBL 2019-2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota C-HR Without JBL 2019-2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota C-HR Without JBL 2019-2020
WIRING DIAGRAM without JBL
STEP 3
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
CONNECT
IF
THERE IS
A MATCH
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota C-HR Without JBL 2019-2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2018-2020
Toyota Camry
With JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota Camry With JBL 2018-2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota Camry With JBL 2018-2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
1
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota Camry With JBL 2018-2020
WIRING DIAGRAM with JBL
STEP 3
STEP 1
RCA CABLES
WHITE
WHITE/BLACK
GRAY
GRAY/BLACK
LF RCA INPUT
RF RCA INPUT
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
CONNECTIONS
NOT
REQUIRED
WITH AMP
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
CONNECT
IF
THERE IS
A MATCH
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota Camry With JBL 2018-2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2018-2020
Toyota Camry
Without JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota Camry Without JBL 2018-2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota Camry Without JBL 2018-2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota Camry Without JBL 2018-2020
WIRING DIAGRAM without JBL
STEP 3
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
CONNECT
IF
THERE IS
A MATCH
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota Camry Without JBL 2018-2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2020
Toyota Corolla
With JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota Corolla With JBL 2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota Corolla With JBL 2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
1
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota Corolla With JBL 2020
WIRING DIAGRAM with JBL
STEP 3
STEP 1
RCA CABLES
WHITE
WHITE/BLACK
GRAY
GRAY/BLACK
LF RCA INPUT
RF RCA INPUT
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
CONNECTIONS
NOT
REQUIRED
WITH AMP
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
CONNECT
IF
THERE IS
A MATCH
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota Corolla With JBL 2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2020
Toyota Corolla
Without JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota Corolla Without JBL 2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota Corolla Without JBL 2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota Corolla Without JBL 2020
WIRING DIAGRAM without JBL
STEP 3
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
CONNECT
IF
THERE IS
A MATCH
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota Corolla Without JBL 2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2020
Toyota Highlander
With JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota Highlander With JBL 2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota Highlander With JBL 2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
1
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota Highlander With JBL 2020
WIRING DIAGRAM with JBL
STEP 3
STEP 1
RCA CABLES
WHITE
WHITE/BLACK
GRAY
GRAY/BLACK
LF RCA INPUT
RF RCA INPUT
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
CONNECTIONS
NOT
REQUIRED
WITH AMP
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
CONNECT
IF
THERE IS
A MATCH
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota Highlander With JBL 2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2020
Toyota Highlander
Without JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota Highlander Without JBL 2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota Highlander Without JBL 2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota Highlander Without JBL 2020
WIRING DIAGRAM without JBL
STEP 3
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
CONNECT
IF
THERE IS
A MATCH
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota Highlander Without JBL 2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2019-2020
Toyota Rav4
With JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota Rav4 With JBL 2019-2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota Rav4 With JBL 2019-2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
1
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota Rav4 With JBL 2019-2020
WIRING DIAGRAM with JBL
STEP 3
STEP 1
RCA CABLES
WHITE
WHITE/BLACK
GRAY
GRAY/BLACK
LF RCA INPUT
RF RCA INPUT
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
CONNECTIONS
NOT
REQUIRED
WITH AMP
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
CONNECT
IF
THERE IS
A MATCH
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota Rav4 With JBL 2019-2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2019-2020
Toyota Rav4
Without JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota Rav4 Without JBL 2019-2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota Rav4 Without JBL 2019-2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota Rav4 Without JBL 2019-2020
WIRING DIAGRAM without JBL
STEP 3
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
CONNECT
IF
THERE IS
A MATCH
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota Rav4 Without JBL 2019-2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2020
Toyota Sequoia
With JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota Sequoia With JBL 2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota Sequoia With JBL 2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
1
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota Sequoia With JBL 2020
WIRING DIAGRAM with JBL
STEP 3
STEP 1
RCA CABLES
WHITE
WHITE/BLACK
GRAY
GRAY/BLACK
LF RCA INPUT
RF RCA INPUT
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
CONNECTIONS
NOT
REQUIRED
WITH AMP
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
CONNECT
IF
THERE IS
A MATCH
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota Sequoia With JBL 2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2020
Toyota Sequoia
Without JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota Sequoia Without JBL 2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota Sequoia Without JBL 2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota Sequoia Without JBL 2020
WIRING DIAGRAM without JBL
STEP 3
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
CONNECT
IF
THERE IS
A MATCH
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota Sequoia Without JBL 2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2018-2020
Toyota Sienna
With JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota Sienna With JBL 2018-2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota Sienna With JBL 2018-2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
1
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota Sienna With JBL 2018-2020
WIRING DIAGRAM with JBL
STEP 3
STEP 1
RCA CABLES
WHITE
WHITE/BLACK
GRAY
GRAY/BLACK
LF RCA INPUT
RF RCA INPUT
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
CONNECTIONS
NOT
REQUIRED
WITH AMP
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
CONNECT
IF
THERE IS
A MATCH
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota Sienna With JBL 2018-2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2018-2020
Toyota Sienna
Without JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota Sienna Without JBL 2018-2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota Sienna Without JBL 2018-2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota Sienna Without JBL 2018-2020
WIRING DIAGRAM without JBL
STEP 3
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
CONNECT
IF
THERE IS
A MATCH
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota Sienna Without JBL 2018-2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2020
Toyota Tacoma
With JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota Tacoma With JBL 2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota Tacoma With JBL 2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
1
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota Tacoma With JBL 2020
WIRING DIAGRAM with JBL
STEP 3
STEP 1
RCA CABLES
WHITE
WHITE/BLACK
GRAY
GRAY/BLACK
LF RCA INPUT
RF RCA INPUT
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
CONNECTIONS
NOT
REQUIRED
WITH AMP
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
CONNECT
IF
THERE IS
A MATCH
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota Tacoma With JBL 2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2020
Toyota Tacoma
Without JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota Tacoma Without JBL 2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota Tacoma Without JBL 2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota Tacoma Without JBL 2020
WIRING DIAGRAM without JBL
STEP 3
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
CONNECT
IF
THERE IS
A MATCH
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota Tacoma Without JBL 2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2020
Toyota Tundra
With JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota Tundra With JBL 2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota Tundra With JBL 2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
1
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota Tundra With JBL 2020
WIRING DIAGRAM with JBL
STEP 3
STEP 1
RCA CABLES
WHITE
WHITE/BLACK
GRAY
GRAY/BLACK
LF RCA INPUT
RF RCA INPUT
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
CONNECTIONS
NOT
REQUIRED
WITH AMP
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
CONNECT
IF
THERE IS
A MATCH
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota Tundra With JBL 2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2020
Toyota Tundra
With Non-JBL Amp
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota Tundra With Non-JBL Amp 2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota Tundra With Non-JBL Amp 2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota Tundra With Non-JBL Amp 2020
WIRING DIAGRAM without JBL
STEP 3
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
CONNECT
IF
THERE IS
A MATCH
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota Tundra With Non-JBL Amp 2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5
INSTALL GUIDE
2020
Toyota Tundra
Without JBL
RETAINS STEERING WHEEL CONTROLS, BACKUP CAMERA, AND MORE!
OR
PRODUCTS REQUIRED
OPTIONAL ACCESSORIES
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRN-RR-TO3 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-TOY03-AS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
Toyota Tundra Without JBL 2020
WELCOME
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
TABLE OF CONTENTS
Installation Instructions
3
Wiring Diagram
4
Troubleshooting Table
5
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
NEED HELP?
1 866 427-2999
[email protected]
maestro.idatalink.com/support
www.12voltdata.com/forum
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
2
Toyota Tundra Without JBL 2020
INSTALLATION INSTRUCTIONS
STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from
aftermarket radio main harness to the TO3 T-harness
and match the wire functions (Note: Rear speaker wire
connections are not required).
• Remove the factory radio.
STEP 2
• Connect the factory harness to the TO3 T-harness.
STEP 3
• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the
aftermarket radio (if equipped).
• Connect the auxiliary cables into the aftermarket radio (if
equipped).
• Plug the steering wheel control cable into the aftermarket
radio.
STEP 4
• Connect all the harnesses to the Maestro RR module then
test your installation.
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
3
Toyota Tundra Without JBL 2020
WIRING DIAGRAM without JBL
STEP 3
STEP 1
CUT AND REMOVE
THE SPEAKER WIRE
JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE - RR SPEAKER (+)
PURPLE/BLACK - RR SPEAKER (-)
BLUE/WHITE - AMP. TURN ON (+)
BLACK - GROUND
RED - ACCESSORY (+)
YELLOW - 12V (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
MAIN
HARNESS
CONNECT TO
AFTERMARKET RADIO
CONNECT
IF
THERE IS
A MATCH
AUX
BACKUP CAM
STEP 2
FACTORY RADIO HARNESS
STEERING WHEEL
CONTROL CABLE
WIRES FROM
VEHICLE
N.C.
STEP 4
MAESTRO RR MODULE
TO3 T-HARNESS
NOT REQUIRED
DATA
CABLE
AUDIO
CABLE
2
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
4
Toyota Tundra Without JBL 2020
TROUBLESHOOTING TABLE
PROBLEM
SOLUTION
When a button on the steering wheel is pressed, the light on the Maestro
module blinks but the radio does not respond.
Ensure the blue 4-pin steering wheel control cable is connected between the
maestro and the radio (the radio will use either the 3.5mm jack or the Blue/
Yellow wire, not both).
Refer to radio’s owners manual to verifie if the radio has this function:
Steering Wheel Control (ON/OFF) : choose ON.
or
Steering Wheel Control (Custom/Preset): choose Preset
The light on the Maestro is flashing RED ONCE.
There is no firmware on the module; flash the RR module.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: 1-866-427-2999
Email: [email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.
Automotive Data Solutions Inc. © 2020
ADS-RR(SR)-TOY03-AS-IG-EN
maestro.idatalink.com
5