Orlaco UM0972225 A 01 User Manual

Monitor 7” HLED
User manual
No. UM0972225 A 01
01/2019
English
Article No. 0226010
Monitor 7” HLED
Contents
User Manual
ORLACO Monitor 7” HLED
Manual number UM0972225, Version A 01
Check with Orlaco which language versions are available. This
manual contains user instructions. Used photographs and
illustrations give general information and may differ from the
products you use.
Contact your Orlaco dealer if you have questions, additional
information, or want to make changes that are not described in this
manual.
Art. no. 0226010;
Monitor 7” HLED
The camera and monitor systems from Orlaco comply with the
latest CE, ADR, EMC and mirror-directive regulations. All products
are manufactured in accordance with the ISO 9001 quality management, IATF 16949 quality automotive and ISO 14001 environmental
management.
For installation Orlaco Monitor 7” HLED
see Manual IM0973585.
Used abbreviations
ABC
OSD
HDR
STND
LCD
CAN
= Auto Backlight Control
= On Screen Display
= High Dynamic Range
= Standard
= Liquid Cristal Display
= Controller Area Network
Article number ORLACO Monitor 7” HLED
This manual describes the operating instructions of the following
ORLACO article numbers. The article numbers can be found on the
label on the back of the Monitors.
HLED Art. Nr. 0226010
2
UM0972225 A 01
Contents
1. Quick Reference
2. Getting Started
2.1. Disclaimer
2.2. Description of the Keyboard
2.3. Language setting for the OSD menu
3. Using the service menu
3.1. Camera settings
3.1.1. Mirror
3.1.2. Upside down
3.1.3. Brightness
3.1.4. Contrast
3.1.5. Saturation
3.1.6. HDR
3.2. Camera tags
3.3. System settings
3.3.1. Language
3.3.2. On Screen Display (OSD)
3.3.3. Keyboard
3.3.4. Power settings
3.3.5. CAN bus
3.3.6. Scanning.
3.3.7. Camera switch
3.3.8. LCD Backlight
3.3.9. Front camera
3.3.10. Tacho settings
3.3.11. Default settings
3.4. Info
4. System overview HLED
5. Overview of menus
6. Version details
UM0972225 A 01
Page
4
5
5
5
5
6
6
6
6
6
6
6
6
6
7
7
7
7
7
8
8
9
9
9
10
10
10
11
12
13
3
1. Quick Reference
Keyboard
Below is a brief description of the key functions. See sections 3 and 4 for a more detailed explanation.
Button 5
Button 3
Button 1
Enter /
standby
Minus select/setting
Camera
selection
Button 2
Button 4
Plus +
select/setting
Option/previous menu
Key 1, camera selection
Button 1
Press the camera selection key once; manual camera selection is enabled. Use the
plus and minus keys to select the camera. Press the key again to disable manual
Button
2
Button 3
Button 4
Button 5
camera
selection.
Key 2, option/previous menu
Return to the previous menu.
Button 1
Button 2
Button 2
Button 3
Button 3
Button 4
Button 4
Button 5
Button 5
Key 3, minus
Go to the next menu option or move left.
Button 3
Button 4
Button 5
Key 4, plus
Go to the previous menu option or move right.
Button 4
Button 5
Key 5, enter/standby
Switch to Standby or in the menus, select or activate the chosen option.
Button 5
4
UM0972225 A 01
2. Getting started
2.1. Disclaimer
Keys
When switching on the monitor for the first time, a disclaimer appears in English for 5 seconds (see Figure 1).
Displayed text: Do not operate display functions during safety critical operations. Objects in the monitor are closer than they appear. If
a different language is subsequently set, the disclaimer text appears
in the set language.
1
2
3
4
5
2.2. Description of the keyboard
Button no. 1 = Camera selection
Button no. 2 = Option/previous menu
Button no. 3 = Minus selection/setting key (-)
Button no. 4 = Plus selection/setting key (+)
Button no. 5 = Enter/Standby
Button 1
Button 2
Button 3
Button 4
Button 5
Figure 1
2.3. Language setting for the OSD (On Screen Display)
menu
The OSD menu language is set as English by default. If you would
like to operate the OSD menu in a different language, open the
service menu → system settings. See section 3 on page 6. The
OSD menu is available in English, Dutch, German, French, Czech,
Hungarian, Italian, Polish, Portuguese, Spanish, Turkish, Swedish,
Finnish, Danish and Norwegian.
UM0972225 A 01
5
3. Service menu
3. Using the service menu
Keys
To open the service menu, simultaneously press the camera selection key (1), the minus key (3) and the plus key (4). The Service
menu (see Figure 2) will appear. The following keys are used to
navigate through the menus:
2 - Option/previous menu: Return to the previous menu
3 - Minus: Go to the next menu option
4 - Plus: Go to the previous menu option
5 - Enter: Select or enable the chosen option
3.1. Camera settings
1
Button 1
Select camera settings. Press enter to open the 'Camera settings' menu.
Press enter again to activate the cursor in the list of items. Use the
minus (3) and plus (4) keys to select the item to adjust and then confirm
this selection by pressing the enter key. If the selection is an on/off
switch, you can choose between on and off. If the selection is a number,
you can change the value using the minus (3) and plus (4) keys. Save
the new settings by pressing the enter key (5).
3.1.1. Mirror
Enable this option to mirror the image (left/right).
3.1.2. Upside down
This option flips the image (upside down).
3.1.3. Brightness
The setting for the brightness of the monitor for the selected
camera.
3.1.4. Contrast
The setting for contrast on the monitor for the selected camera.
3.1.5. Saturation
The setting for color saturation on the monitor for the selected
camera.
3.1.6 Switch delay
Enable this option if the switchwire is controlled by an intermittent
signal (e.g. from an indicator light).
3.1.7. HDR
Enable this option for the High Dynamic Range camera mode. Turn
on or off.
2
Button 2
3
4
Button 3
5
Button 4
Button 5
Figure 2
Figure 3
Figure 4
3.2. Camera tags
See Figure 5. In this menu, names can be given to the camera
inputs.
Figure 5
6
UM0972225 A 01
3. Service menu
3.3. System settings (see Figure 6)
3.3.1. Language
See Figure 7. This option opens the language selection menu. The
selected language will be used for all OSD menus. The OSD menu is
available in English, Dutch, German, French, Czech, Hungarian,
Italian, Polish, Portuguese, Spanish, Turkish, Swedish, Finnish,
Danish and Norwegian.
3.3.2. On Screen Display (OSD)
This option opens the OSD settings menu. See Figure 8.
The following can be set in this menu:
OSD time-out
Sets the time (in seconds) that the OSD (camera number/name,
top left) appears on the monitor. Select 'Off' to disable this and
'On' to have this permanently enabled.
Info transparency
Changes the transparency of the camera tag, etc.
Menu transparency
Changes the transparency of the system menu.
Disclaimer transparency
Changes the transparency of the disclaimer when starting up.
OSD menu help
This function enables or disables the automatic text messages
of the OSD help menus. If enabled, help messages automatically
appear in all menus after 10 seconds of inactivity.
3.3.3. Keyboard
This option opens the keyboard menu. See Figure 9.
Keyboard lock
This option opens the settings menu for the keyboard lock. It
is possible to lock various functions in order to prevent any
unwanted changes. See Figure 10.
3.3.4. Power settings
See Figure 11. This menu has the following option:
Standby mode
There are three available choices — use the minus and plus keys
to select the various functions.
MNU = With this setting you access the operator menu via the
enter key (5). Select the required setting.
IMM = Immediate standby.
2S = Standby after a delay of 2 seconds.
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
UM0972225 A 01
7
3. Service menu
3.3.5. CAN bus
See Figure 12. This option opens the CAN bus menu. This menu
has the following 5 options:
CAN protocol
This option selects the signal, or CAN protocol, that the Monitor
uses. By default this is Orlaco CAN protocol 1. Other protocols
are customer-specific. The CAN speed is automatically adjusted,
but it can also be set manually once the protocol has been
selected.
CAN speed
This option selects the bit rate of the CAN bus. Available options
are: 100, 125, 200, 250, 500 and 1000 kbit.
Set CAN-ID
The Orlaco CAN protocol has an ID (default 0) to control multiple
monitors via one CAN bus. The ID is inactive when the text is
blue and becomes active when the protocol is set to 1. The CANID can be set from 0-15 where 0 is the default value.
Terminator
Enable/disable the 120 Ω terminator (CAN or RS485) between Rx
and Tx.
3.3.6. LCD backlight
This option opens the backlight submenu for the Monitor 7” HLED.
See Figure 13. This menu has the following 4 options:
LCD backlight mode
This option enables automatic backlight control (ABC). The Monitor automatically adapts its brightness to the ambient light. If
required, a specific day or night brightness can be manually set.
Alternatively, the user can choose to manually adjust the day or
night brightness setting or select a red or blue night mode.
ABC = Standard Automatic Brightness Control
A_B = ABC blue mode
A_R = ABC red mode
DAY = Day mode (can be adjusted between 50–100%)
NIT = Night mode (can be adjusted between 0–50%)
N_B = Night blue mode (can be adjusted between 0–50%),
N_R = Night red mode (can be adjusted between 0–50%)
ABC minimum level
This setting determines the minimum brightness the ABC can use
when there is low ambient light.
LCD backlight day
This option allows the day brightness setting to be manually
adjusted (50–100%).
LCD backlight night
This option allows the night brightness setting to be manually
adjusted (0–50%).
8
Figure 12
Figure 13
UM0972225 A 01
3. Service menu
3.3.7. Scanning
This option opens the camera scanning submenu. See Figure 14.
This menu has the following options:
Scan sequence
This option selects the cameras from which images are to be
shown in sequence.
Scan interval
This option selects how long a camera image is displayed.
3.3.8. Camera switch
This option configures the type of video switch that is used. See
Figure 15.
‘OFF’-if no camera switch is used → 1 camera system.
‘2C’-when only 2 cameras are connected to the 4 channel switch.
‘3C’-when only 3 cameras are connected to the 4 channel switch.
‘4C’-for the combination with the external switch 0404240 for 4
cameras → 4 camera system.
3.3.9. Front camera
This option opens the front camera submenu for the 7” HLED Monitor.
This enables the front camera functionality (a statutory obligation).
Function AUX wire, see figure 16.
Defines the function of the AUX1 & AUX2 switching wires (grey
and yellow). Select TCH for the tachometer function (Tacho to
AUX1 and hand brake to AUX2) or ZOO for the camera zoom function (only available in combination with an auto focus camera).
Use in this case the AUX1 & AUX2 switching wires to zoom in and
out. Select KEY to block the keyboard fully by activating the wire
AUX1.
Select Q+- to select the next and previous camera with the AUX switch
wires.
3.3.10. Tacho settings see figure 18.
Settings related to switching a camera based on tacho speed:
AUX wire function:
Select the function of the AUX1 and AUX2 wires.
OFF
AUX wires no function.
C12 with the use of the digicoax switcher 0404240;
Aux wires open = Monitor standby.
Aux wire 1 = activate Cam 1.
Aux wire 2 = activate Cam 2.
C23 with the use of the digicoax switcher 0404240,
Aux wires open = activate Cam 1.
Aux wire 1 = activate Cam 2.
Aux wire 2 = activate Cam 3.
C1+
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
UM0972225 A 01
9
3. Service menu
Aux wires open = Monitor standby.
Aux wire 1 = activate selected camera (wire2).
Aux wire 2 = activate Cam toggle 1 to 4.
TCH
for the tachometer.
KEY
for + and - key functions on AUX1/2.
C-+
Aux wires open = activate Cam 1 or Monitor standby.
Aux wire 1 = activate Cam toggle up 1 to 4.
Aux wire 2 = activate Cam toggle down 1 to 4.
Pulses per meter
Set this value to the amount of pulses the tachometers generates
per meter. (0 - 250).
Cam to activate
Select wich camera should be activated when tacho speed is within
selected range. (C1 - C6).
Cam on if speed >= (0 - 130)
Tacho low limit, Camera not activated when tacho < low limit.
.... and speed < (0 - 130)
Tacho high limit, Camera not activated when tacho > high limit.
Both menus Cam if speed >= and .. and speed < are connected;
Camera activated when tacho >= low limit and tacho < high limit.
The 2 conditions together must be active to switch the camera.
Figure 19
Figure 20
3.3.11. Default settings
See figure 19. This option opens the menu to restore the factory
default settings. Select the number of the factory settings that you
require (39 = default Orlaco settings).
Contact ORLACO for further information. Select the option ‘Restore
defaults’ to restore the factory settings. See figure 19.
3.4. Info
This user manual describes the functions of the software version
indicated on this Monitor (see Figure 20).
10
UM0972225 A 01
4. System overview HLED
1 camera system
Monitor 7” HLED
Art. No. 0226010
Camera HMOS
with bracket
Power
12...24V/DC
Cable Uni DigiCoax
4 camera system
4x
HMOS Camera
with bracket
Camera 1
Monitor 7” HLED
Art. No. 0226010
Cable DigiCoax
Camera 2
Cable DigiCoax
Camera 3
Cable DigiCoax
Camera 4
Cable DigiCoax
Power
24V/DC
DigiCoax Switcher
Art. No. 0404240
UM0972225 A 01
11
5. Overview of menus
Service menu
Camera- + Minus- and Plus buttons
Service menu
Camera settings
Camera tags
System settings
Info
Mirror, Upside down, Brightness, Contrast, Saturation, switch delay, HDR
1, 2, 3
System settings
Language
On screen display
Keyboard
Power settings
CAN-bus
LCD-Backlight
Scanning
Camera switch
Frontcam
Tacho settings
Default settings
English, Dutch, German, French, Czech, Hungarian,
Italian, Polish, Portuguese, Spanish, Turkish, Swedish, Finnish, Danish and Norwegian.
On screen display
OFF, 4c, 2c, 3c,
ON, OFF, 30sec, 10sec, 3sec
29 positions
29 positions
29 positions
ON/OFF
OSD timeout
Info transparency
Menu transparency
Disclaimer transp.
OSD menu help
Keyboard
Keyboard lock
Keyboard lock
Frontcam
Enable Frontcam
Invert handbrake
Pulses per meter
AUX wire function
OFF 1c, 2c, 3c
ON/OFF
0-100
OFF, TCH, ZOO,
KEY, C+-
Tacho Settings
OFF, C12, C23,
C1+, TCH, KEY, C-+
0 - 250
C1 - C6
0 - 130
0 - 130
AUX wire function
Pulses per meter
Cam to activate
Cam on if speed >=
... and speed <
Default settings
Select defaults
Restore defaults
1-30
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
Standby menu
Operator menu
Camera switch
Camera settings
Standby
Power settings
Standby mode
IMM, MNU, 2sec
CAN-bus
CAN-protocol
CAN-speed
Set CAN-ID
Terminator
OFF, 1-6 positions
1M, 500, 250, 200, 125, 100
0 - 15
ON/OFF
LCD-backlight
ABC, A_B, A_R,
NIT, N_B, N_R, DAY
LCD-backlight mode
ABC Minimum level
LCD-backlight day
LCD-backlight night
0-50
50-100
0-50
Scanning
Scan sequence
Scan interval
12
OFF, 1-2, 1-2-3
2s, 5s, 10s
UM0972225 A 01
6. Version details
Version A 01. First issue, January 2019.
UM0972225 A 01
13
14
UM0972225 A 01
UM0972225 A 01
15
ORLACO
Orlaco is a Manufacturing company that specializes in making cameras and
monitor systems for commercial vehicles, fork-lift trucks, cranes, off shore
and maritime.
Our objective is to design and produce camera systems for the professional
market that improve the drivers’ view and increase operating efficiency.
At our facility in Barneveld we locate our design, manufacturing, warehousing
and service department.
Vision is our mission®. Orlaco therefore deploys the development, manufacture, supply and service of camera and Monitor systems that will improve
safety and efficiency of all vehicles, machinery and vessels. Our systems
give the end user a view on each blind spot and will create comfort and
improved working conditions. Our active approach will support market
demands and innovations and will lead to enthusiastic ambassadors in the
market; our customers.
For more information: www.orlaco.com
www.orlaco.com